2006 Jeep Grand Cherokee SRT8 Owners Manual

should be between the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for coolant freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill.

318 MAINTAINING YOUR VEHICLE

Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot coolant to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing.

• If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pres- sure tested for leaks. • Maintain coolant concentration at 50% HOAT engine coolant (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also. • Do not change the thermostat for summer or winter install

operation. If replacement is ever necessary,

ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions.

Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, tears, cuts, abrasions, and exces- sive swelling indicate deterioration of the rubber. Pay particular attention to those hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not come in contact with any heat source or moving component which may cause heat damage or mechanical wear. Insure nylon tubing in these areas has not melted or collapsed.

MAINTAINING YOUR VEHICLE 319

Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found on the appro- priate “Maintenance Schedule.” Refer to Section 8 of this manual.

320 MAINTAINING YOUR VEHICLE

WARNING!

Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency.

Brake And Power Steering Hoses When the vehicle is serviced for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasion, and excessive swelling indicate deterioration of the rubber. Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold.

Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to facilitate the assembly of hoses to couplings. Therefore, oil wetness at the hose-coupling area is not necessarily an indication of leakage. Actual dripping of hot fluid when systems are under pressure (during vehicle operation), should be noted before a hose is replaced based on leakage. Inspection of brake hoses should be performed NOTE: whenever the brake system is serviced and at every engine oil change. Inspect hydraulic brake hoses for surface cracking, scuffing, or worn spots. If there is any evidence of cracking, scuffing, or worn spots, the hose

should be replaced immediately! Eventual deterioration of the hose can take place resulting in a possibility of a burst failure.

WARNING!

Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately.

Brake Fluid Level Check The fluid level in the master cylinder should be checked when performing underhood services, or immediately if the brake system warning light indicates system failure.

MAINTAINING YOUR VEHICLE 321

Clean the top of the master cylinder area before removing the cap. Add fluid to bring the level up to the top of the “FULL” mark on the side of the master cylinder reservoir. Overfilling of fluid is not recommended because it may cause leaking in the system. Add enough fluid to bring the level up to the require- ments described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type.

322 MAINTAINING YOUR VEHICLE

WARNING!

• Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that has a lower initial boiling point than the recommended MOPAR DOT 3
product or a brake fluid that is unidentified as to FMVSS specification may result in sudden brake failure during hard prolonged braking. You could have an accident.

Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture.

CAUTION!

Do not allow petroleum base fluid to contaminate the brake fluid, all brake seal components could be damaged causing partial or complete brake failure.

Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses and quick connect fittings which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline. You are urged to use only the manufacturer’s specified hoses with quick connect fittings, or their equivalent in material and specification, in any fuel system servicing. It is mandatory to replace any damaged hoses or quick connect fittings that have been removed during service.

Care should be taken in installing quick connect fittings to insure they are properly installed and fully connected. See your authorized dealer for service. Automatic Transmission

Fluid Level Check Regular automatic transmission fluid level checks are not required. For this reason the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level.

MAINTAINING YOUR VEHICLE 323

CAUTION!

Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to the Fluids, Lubricants and Genuine Parts section for correct fluid type.

324 MAINTAINING YOUR VEHICLE

CAUTION!

The fluid level is preset at the factory and does not require adjustment under normal operating condi- tions. If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe damage to the transmission may occur. Your authorized dealer has the proper tools to accurately adjust the fluid level.

Fluid and Filter Changes Automatic transmission fluid and filter should be changed as follows: Maintenance Schedule “A” — No change necessary. Maintenance Schedule “B” – Every 60,000 miles (100 000
km) change fluid and filter under the following condi- tions:

• Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation.

If the transmission is disassembled for any reason, the fluid and filter should be changed. Front And Rear Wheel Bearings Front and rear wheel bearings are permanently sealed. No regular maintenance is required for these compo- nents. Appearance Care And Protection From Corrosion

Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.

The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants.

MAINTAINING YOUR VEHICLE 325

Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using Mopar威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumu- lated on your vehicle, use Mopar威 Super Kleen Bug and Tar Remover to remove. • Use Mopar威 Cleaner Wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.

326 MAINTAINING YOUR VEHICLE

CAUTION!

Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.

Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and tailgate must be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.

• If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibil- ity of the owner. • Aluminum wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use Mopar威 Wheel Cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only Mopar威 cleaners are recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed.

mud or stone shields behind each wheel.

• If a lot of driving is done on gravel roads, consider • Use Mopar威 Touch Up Paint on scratches or chips as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle.

Interior Care Use Mopar威 Total Clean to clean fabric upholstery and carpeting. Interior Trim should be cleaned starting with a damp cloth, a damp cloth with Mopar威 Total Clean, then Mopar威 Spot & Stain Remover if absolutely necessary. Do not use harsh cleaners or Armorall. Use Mopar威 Total Clean to clean vinyl upholstery. Leather Seat Care & Cleaning Mopar威 Total Clean is specifically recommended for leather upholstery.

MAINTAINING YOUR VEHICLE 327

Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar威 Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition.

WARNING!

Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.

328 MAINTAINING YOUR VEHICLE

Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag.

2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use Mopar威 Total Clean, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly.

FUSE PANEL

Interior Fuses The fuse panel is on the lower instrument panel just to the left of the steering column.

MAINTAINING YOUR VEHICLE 329

Cavity

10
11
12

13
14

15

Fuse Panel Location Description Audio Amp (B+)

Fuse/Color 30 Amp Green 15 Amp Blue Sunroof (B+) 10 Amp Red Htd Mirror (EBL)

Cavity

Door Locks (B+)

Description Rr Pwr Out (B+)

Fuse/Color 20 Amp Yel- low 10 Amp Red Rr HVAC (R/O) 10 Amp Red OCM (B+) 20 Amp Yel- low 15 Amp Blue Steer Col Lock (B+) 20 Amp Yel- low 10 Amp Red Ign Run Only Out (R/O) Spare 10 Amp Red Mem. Sw, Courtesy Lamp

Pwr Outlet (B+)

(B+)

Spare 20 Amp Yel- low 10 Amp Red Tire Press Mon (R/O)

Cigar Ltr (R/A)

330 MAINTAINING YOUR VEHICLE

Cavity 16
17
19
20
21
22
24
25

CB1
CB2
CB3

Description

Fuse/Color 10 Amp Red SCM, Cluster OBD (B+) 15 Amp Blue Flipper Glass (B+) 10 Amp Red OCM (R/S) 10 Amp Red WCM, Cluster (R/S) 15 Amp Blue Autowipe (Accy Delay) 15 Amp Blue Rear Wiper (B+) 10 Amp Red PDC, FCM, A580 (R/S) 10 Amp Red ABS, Trans. Case Switch

20 Amp 20 Amp 20 Amp

(R/S) Cycle -Wipers (B+) Non - Cycle Seats (B+) Non - Cycle Windows (De- lay)

Underhood Fuses (Power Distribution Center)

Power Distribution Center

Cavity 10
11
12
13
14
15

ASD

Description

Fuse/Color 40 Amp Green HVAC Blower 30 Amp Pink Power Outlets Rr Wiper/Ign R/O 30 Amp Pink 30 Amp Pink ABS Pump Spare 50 Amp Red Spare 40 Amp Green Acc Delay/Seats Spare 40 Amp Green Starter/JB Power 30 Amp Pink 40 Amp Green EBL/Htd Mirror 40 Amp Green JB Power Spare Spare

Cig Ltr/T-Tow

MAINTAINING YOUR VEHICLE 331

Cavity 16

17
18
19
20
21
22
23
24
25
26
27
28

29

ABS Valves

Description IPM/Coils

Fuse/Color 25 Amp Natu- ral Spare 20 Amp Yellow TCM/AC Clutch 20 Amp Yellow Ign Sw 20 Amp Yellow PCM Batt (Gasoline Only) 30 Amp Pink Spare 20 Amp Yellow FDCM 20 Amp Yellow Fuel Pump 20 Amp Yellow FDCM/E-Diff. Spare 15 Amp Blue 25 Amp Natu- ral Spare

Brake/Stop Lamps NGC/Injectors

332 MAINTAINING YOUR VEHICLE

Cavity 30
31
32
33
34
35
36
38
39
40

Fuse/Color Spare Spare Micro Relay Micro Relay Micro Relay Micro Relay Spare Spare Mini Relay Mini Relay

Description

Underhood Fuses (Integrated Power Module)

TCM Rly (Gasoline Only) Starter Rly AC Clutch Rly Fuel Pump Rly

HVAC Blower Rly ASD Rly

Integrated Power Module

Cavity 10
11
12
13
14
15
16

Description Wiper On/Off Rly Wiper Hi/Lo Rly Horn Rly

Fuse/Color Micro Relay Micro Relay Micro Relay Spare Micro Relay Micro Relay Micro Relay 10 Amp Red 10 Amp Red 10 Amp Red Mini Relay 20 Amp Yellow FCM Batt #4
20 Amp Yellow FCM Batt #2
20 Amp Yellow Adjustable Pedal 20 Amp Yellow Ft Fog Lamps 20 Amp Yellow Horn

Lt T-Tow Stop/Turn Rly Rt T-Tow Stop/Turn Rly Park Lamps Rly Lt Park Lamps T-Tow Park Lamps Rt Park Lamps Rad Fan Hi Rly

MAINTAINING YOUR VEHICLE 333

Cavity 17
18
19
20
21
22
23
24
25
26
27
28
29
30

Description

Fuse/Color 20 Amp Yellow Rear Fogs 20 Amp Yellow FCM Batt #1
20 Amp Yellow Lt T-Tow Stop/Turn 20 Amp Yellow FCM Batt #3
20 Amp Yellow Rt T-Tow Stop/Turn 30 Amp Pink 50 Amp Red Mini Relay Micro Relay Micro Relay 15 Amp Blue 20 Amp Yellow IOD #2 (Audio) ORC (Ign R/.S) 10 Amp Red 10 Amp Red ORC (Ign R/O)

FDCM Mod Rad Fan Rad Fan Lo Rly Ft Fog Lamps Rly Adjustable Pedal Rly IOD #1

334 MAINTAINING YOUR VEHICLE

labeled Ignition-Off Draw (IOD#1).

VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21
days you may want to take steps to protect your battery. You may: • Remove fuse #27 in the Intelligent Power Module • Or, disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.

REPLACEMENT BULBS

Interior Lights Bulb Type Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194
Grab Handle Light . . . . . . . . . . . . . . . . L002825W5W Overhead Console Reading Lights . . . . . . . . . . VT4976
Rear Cargo Light . . . . . . . . . . . . . . . . . . . . . . . 214–2
Visor Vanity Light . . . . . . . . . . . . . . . . . . . . . V26377
Underpanel Courtesy Lights. . . . . . . . . . . . . . . . . 906
Instrument Cluster (General Illumination) . . . . . . . 103
Telltale/Hazard Light . . . . . . . . . . . . . . . . . . . . . . 74
* Available only from authorized dealers.

Exterior Lights Bulb Type Backup Lights . . . . . . . . . . . . . . . . . . . . . . . . . 3157K Front Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . 9145
Front Park/Turn Light . . . . . . . . . . . . . . . . . . . 3157K Front Side Marker . . . . . . . . . . . . . . . . . . . . . . . 2825
Headlights (Low Beam) . . . . . . . . . . . . . . . . . . . 9006
Headlights (High Beam) . . . . . . . . . . . . . . . . . . . 9005
Rear License Plate Light. . . . . . . . . . . . . . . . . . . . 168
Rear Stop/Tail Lights . . . . . . . . . . . . . . . . . . . . 3157K Rear Turn/Tail Lights (2) . . . . . . . . . . . . . . . . . . 3157
NOTE: Numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable Service Manual.

MAINTAINING YOUR VEHICLE 335

BULB REPLACEMENT

Head Light

1. Open the hood. 2. Remove the headlamp cover.

336 MAINTAINING YOUR VEHICLE

3. Turn the low or high beam bulb 1/4 turn counter clockwise to remove from housing.

4. Disconnect the electrical connector and replace the bulb.

CAUTION!

Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.

Front Turn Signal

1. Open the hood. 2. Remove the headlamp cover.

MAINTAINING YOUR VEHICLE 337

4. Disconnect the electrical connector and replace the bulb.

3. Turn the turn signal bulb 1/4 turn counter clockwise to remove from housing.

338 MAINTAINING YOUR VEHICLE

CAUTION!

CAUTION!

Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.

Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.

Front Fog Light

1. Reach behind the front fascia from under the vehicle. 2. Turn the front fog light bulb 1/4 turn counter clock- wise to remove from housing. 3. Disconnect the electrical connector and replace bulb.

Rear Tail, Stop, Turn Signal, and Back-Up Lights

1. Raise the liftgate. 2. Remove the two Torx fasteners.

MAINTAINING YOUR VEHICLE 339

3. Squeeze the socket assembly tabs to remove it from the housing.

4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the light assembly.

340 MAINTAINING YOUR VEHICLE

Center High Mounted Stop Light (CHMSL)

1. Remove the two screws securing the CHMSL.

2. Twist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL.

FLUID CAPACITIES

Fuel (Approximate) Engine Oil with Filter

6.1 Liter Engine (SAE 0W-40, API Certified)

Cooling System * 6.1 Liter Engine (Mopar威 Engine Coolant/Antifreeze 5 Year/

100,000 Mile Formula)

* Includes heater and coolant recovery bottle filled to MAX level.

MAINTAINING YOUR VEHICLE 341

U.S.

20.6 Gallons

7 Qts

14.8 Qts

Metric 78 Liters

6.6 Liters

14 Liters

342 MAINTAINING YOUR VEHICLE

FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant

Engine Oil (6.1L Engine)

Oil Filter (6.1L Engine) Spark Plugs

Fuel Selection (6.1L Engine)

Fluid, Lubricant, or Genuine Part Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) Use API Certified SM/CF synthetic engine oil. SAE 0W-40 is recommended, meeting the requirements of DaimlerChrysler Material Standard MS-10725. Mopar威 Oil Filter (P/N 05281090) or equivalent. Refer to the Vehicle Emission Control Information label in the engine com- partment. Premium Unleaded 91 Octane Only or higher.

Chassis Component Automatic Transmission Transfer Case

Axle Differential (Front-Rear)

Brake Master Cylinder

Power Steering Reservoir

MAINTAINING YOUR VEHICLE 343

Fluid, Lubricant, or Genuine Part Mopar威 ATF+4 Automatic Transmission Fluid Castrol威 BOT89 M1 Plus Lubricant Usage of other fluid/lubricants is NOT recommended. Mopar威 Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent. Mopar威 DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only rec- ommended brake fluids. This system requires the use of Mopar威 Hydraulic System Power Steering Fluid (P/N 05142893AA) or equivalent, which meets DaimlerChrysler Ma- terial Standard MS-10838.

MAINTENANCE SCHEDULES

CONTENTS

䡵 Emission Control System Maintenance . . . . . . . . 346
䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 346

▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 349
▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 358

M

346 MAINTENANCE SCHEDULES

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditions such as dusty areas and very short trip driving. Inspection and service also should be done any time a malfunction is suspected. NOTE: Maintenance, replacement, or repair of the emis- sion control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part which has been certified pursuant to U.S. EPA or, in the State of Califor- nia, California Air Resources Board regulations.

MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule ⴖBⴖ. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) • More than 50% of your driving is at sustained high • Trailer towing

speeds during hot weather, above 90°F (32°C)

NOTE: Most vehicles are operated under the conditions listed for Schedule “B.” If ANY of these apply to you, change your NOTE: engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow the maintenance rec- ommendations in “Maintenance Schedule B.” If ANY of these apply to you then flush and NOTE: replace your engine coolant every 102,000 miles (170 000
km) or 60 months, whichever comes first, and follow “Schedule B” of the “Maintenance Schedules” section of this manual. Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Sched- ule “B.” Use the schedule that best describes your driving condi- tions. Where time and mileage are listed, follow the interval that occurs first.

MAINTENANCE SCHEDULES 347

CAUTION!

Failure to perform the required maintenance items may result in damage to the vehicle.

At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent, add as required.

348 MAINTENANCE SCHEDULES

damage.

Once a Month • Check the tire pressure and look for unusual wear or • Inspect the battery and clean and tighten the terminals • Check the fluid levels of the coolant reservoir, brake • Check all lights and all other electrical items for correct

master cylinder, and add as needed.

as required.

operation.

At Each Oil Change • Change the engine oil filter. • Inspect the exhaust system. • Inspect brake hoses. • Check the engine coolant/anti-freeze level, hoses, and

clamps.

Schedule “B” Follow this schedule if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) • More than 50% of your driving is at sustained high

speeds during hot weather, above 90°F (32°C)

SCHEDULE “B” 349

• Trailer towing If ANY of these apply to you, change your NOTE: engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow the maintenance rec- ommendations in “Maintenance Schedule B.” If ANY of these apply to you then flush and NOTE: replace your engine coolant every 102,000 miles (170 000
km) or 60 months, whichever comes first, and follow “Schedule B” of the “Maintenance Schedules” section of this manual.

350 SCHEDULE “B”

Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary. Drain and refill the front and rear axles. Inspect the brake linings.

3,000
(5 000)

6,000
(10 000)

9,000
(15 000)

12,000
(20 000)

15,000
(25 000)

SCHEDULE “B” 351

Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary. Inspect the PCV Valve, replace if necessary.〫 Drain and refill the front and rear axles. Inspect the brake linings. Drain the transfer case and refill.

18,000
(30 000)

21,000
(35 000)

24,000
(40 000)

27,000
(45 000)

30,000
(50 000)

352 SCHEDULE “B”

Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary. Drain and refill the front and rear axles. Inspect the brake linings.

33,000
(55 000)

36,000
(60 000)

39,000
(65 000)

42,000
(70 000)

45,000
(75 000)

SCHEDULE “B” 353

Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary. Inspect the PCV Valve, replace if necessary.〫 Inspect drive belt, replace if necessary. Inspect the brake linings. Drain and refill the front and rear axles. Drain and refill the transfer case fluid. Drain and refill the automatic transmission fluid, and replace filter. Flush and replace engine coolant/anti-freeze.

48,000
(80 000)

51,000
(85 000)

54,000
(90 000)

57,000
(95 000)

60,000
(100 000)

354 SCHEDULE “B”

Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary. Inspect the drive belt, replace if necessary. Inspect the brake linings. Drain and refill the front and rear axle fluid.

63,000
(105 000)

66,000
(110 000)

69,000
(115 000)

72,000
(120 000)

75,000
(125 000)

Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary. Inspect the PCV Valve, replace if necessary.〫 Inspect the drive belt, replace if necessary.* Drain and refill the transfer case fluid. Inspect the brake linings. Drain and refill the front and rear axle fluid.

78,000
(130 000)

81,000
(135 000)

84,000
(140 000)

87,000
(145 000)

90,000
(150 000)

SCHEDULE “B” 355

356 SCHEDULE “B”

Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary. Replace the spark plugs. Inspect the drive belt, replace if necessary.* Inspect the brake linings. Drain and refill the front and rear axle fluid. Flush and replace the engine coolant/anti-freeze, if not done at 60 months.

93,000
(155 000)

96,000
(160 000)

99,000
(165 000)

102,000
(170 000)

105,000
(175 000)

Miles (Kilometers) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Inspect the drive belt, replace if necessary.* Inspect the brake linings. Drain and refill the front and rear axle fluid. Drain and refill the automatic transmission fluid, and re- place filter. Drain and refill the transfer case fluid. Flush and replace the engine coolant/anti-freeze at 120
months, if not replaced at 102,000 miles (170 000 km). Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. 〫 This maintenance is recommended by the manufac- turer to the owner, but is not required to maintain emissions warranty.

SCHEDULE “B” 357

108,000
(180 000)

111,000
(185 000)

114,000
(190 000)

117,000
(195 000)

120,000
(200 000)

* This maintenance is not required if the belt was previously replaced.

358 SCHEDULE “A”

Schedule “A” Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Inspect the engine air cleaner filter, and replace if necessary. Inspect the brake linings. Drain the transfer case and refill.

6,000
(10 000)

[6]

12,000
(20 000)

[12]

18,000
(30 000)

24,000
(40 000)

30,000
(50 000)

[24]

[18]

[30]

Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Inspect the brake linings.

SCHEDULE “A” 359

36,000
(60 000)

[36]

42,000
(70 000)

[42]

48,000
(80 000)

[48]

54, 000
(90 000)

[54]

360 SCHEDULE “A”

Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Inspect the engine air cleaner filter, and replace if nec- essary. Inspect the PCV Valve, replace if necessary.〫 Inspect the drive belt, replace if necessary. Flush and replace the engine coolant/anti-freeze at 60
months, if not replaced at 102,000 miles (170 000 km). Inspect the brake linings. Drain the transfer case and refill.

60,000
(100 000)

66,000
(110 000)

72,000
(120 000)

78,000
(130 000)

[60]

[66]

[72]

[78]

SCHEDULE “A” 361

Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Inspect the engine air cleaner filter, and replace if nec- essary. Inspect the PCV Valve, replace if necessary.〫 Replace the spark plugs. Inspect the drive belt, replace if necessary.* Inspect the brake linings. Flush and replace the engine coolant/anti-freeze if not replaced at 60 months. Drain the transfer case and refill.

84,000
(140 000)

90,000
(150 000)

96,000
(160 000)

[84]

[96]

[90]

102, 000
(170 000)

[102]

M

362 SCHEDULE “A”

Miles (Kilometers) [Months] Change the engine oil and engine oil filter. Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary.〫 Inspect the drive belt, replace if necessary.* Inspect the brake linings. Flush and replace the engine coolant/anti-freeze if not done at 102,000 miles (170 000 km). Drain the transfer case and refill. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. 〫 This maintenance is recommended by the manufac- turer to the owner, but is not required to maintain emissions warranty.

108,000
(180 000)

[108]

114,000
(190 000)

[114]

120,000
(200 000)

[120]

* This maintenance is not required if the belt was previously replaced.

WARNING!

You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.

SCHEDULE “A” 363

IF YOU NEED CONSUMER ASSISTANCE

CONTENTS

䡵 Suggestions For Obtaining Service For Your

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
▫ Prepare For The Appointment . . . . . . . . . . . . 366
▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 366
▫ Be Reasonable With Requests . . . . . . . . . . . . . 366
䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . . 366

䡵 Warranty Information (U.S. Vehicles Only) . . . . . 369
䡵 Mopar威 Parts . . . . . . . . . . . . . . . . . . . . . . . . . 369
䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . . 369
▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 369
䡵 Publication Order Forms . . . . . . . . . . . . . . . . . . 370

366 IF YOU NEED CONSUMER ASSISTANCE

SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE

Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem. Prepare A List Make a written list of your vehicle’s problems or the specific work you want done. If you’ve had an accident, or work done that is not on your maintenance log, let the service advisor know.

Be Reasonable With Requests If you list a number of items, and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many dealers you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an ap- pointment.

IF YOU NEED ASSISTANCE The manufacturer and its dealers are vitally interested in your satisfaction. We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service. The manufacturer’s dealers have the facilities, factory-trained

technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you

may contact the Manufacturer’s Customer Center.

Any communication to the Manufacturer’s Customer Center should include the following information: • Owner’s name and address • Owner’s telephone number (home and office) • Dealership name

IF YOU NEED CONSUMER ASSISTANCE 367

• Vehicle identification number • Vehicle delivery date and mileage DaimlerChrysler Motors Corporation Customer Center P.O. Box 21–8004
Auburn Hills, MI 48321–8004
Phone: (800) 992-1997
DaimlerChrysler Canada Inc. Customer Center P.O. Box 1621
Windsor, Ontario N9A 4H6
Phone —(800) 465–2001
In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240
Sante Fe C.P. 05109
Mexico, D. F. In Mexico (915) 729–1248 or 729–1240
Outside Mexico (525) 729–1248 or 729–1240

368 IF YOU NEED CONSUMER ASSISTANCE

Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY. Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands be- hind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date. If you have any questions about your service

contract, call the manufacturer’s Service Contract Na- tional Customer Hotline at 1-800-521-9922. The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract. If you purchased a service contract that is not a manufacturer’s Service Contract, and you require service after your manufactur- er’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.

WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle.

MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best.

REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy

IF YOU NEED CONSUMER ASSISTANCE 369

campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, and the manufacturer. To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.NHTSA.gov. or write to: NHTSA, U.S. Dept. of Transportation, Washington DC 20590. You can also obtain other information about motor vehicle safety from the Hotline. In Canada: If you believe that your vehicle has a safety defect, you should contact the Customer Service Department imme- diately. Canadian customers who wish to report a safety defect to the Canadian government should write to Transport Canada, Motor Vehicle Defect Investigations and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B 3V9.

370 IF YOU NEED CONSUMER ASSISTANCE

PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.

These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts.

• Diagnostic Procedure Manuals.

Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computer- controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-by-step troubleshooting and driveability procedures, proven diagnostic tests and a complete list of all tools and equipment.

• Owner’s Manuals.

These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.

Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals

IF YOU NEED CONSUMER ASSISTANCE 371

INDEX

10

374 INDEX

ABS (Anti-Lock Brake System) . . . . . . . . . . . . 177,243
Adding Engine Coolant (Antifreeze) . . . . . . . . . . 316
Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 169
Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 270
. . . . . . . . . . . . . . . . . . . . . . . 144
Adjustable Pedals . . . . . . . . . . . . . . . 309
Air Conditioner Maintenance Air Conditioning Refrigerant . . . . . . . . . . . . . . . 310
Air Pressure, Tires . . . . . . . . . . . . . . . . . . . . . . . 258
Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . 55
Airbag Light . . . . . . . . . . . . . . . . . . . . . . . 57,71,177
Airbag Maintenance . . . . . . . . . . . . . . . . . . . . . . . 56
Alarm (Security Alarm) . . . . . . . . . . . . . . . . . 25,178
Alarm System (Security Alarm) . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . 264
Alignment and Balance Alterations/Modifications, Vehicle . . . . . . . . . . . . . 8
Antenna, Satellite Radio . . . . . . . . . . . . . . . . . . . 218
Antifreeze (Engine Coolant) . . . . . . . . . . . . . . 315,341
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 317

Disposal

Anti-Lock Brake System (ABS) . . . . . . . . . . . . 131,243
Anti-Lock Warning Light . . . . . . . . . . . . . . . . . . 177
Anti-Theft System . . . . . . . . . . . . . . . . . . . . . 25,178
Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . 324
. . . . . . . . . . . . . . . . 30
Auto Down Power Windows Automatic Dimming Mirror . . . . . . . . . . . . . . . . . 78
Automatic Door Locks . . . . . . . . . . . . . . . . . . . . . 19
Automatic Headlights . . . . . . . . . . . . . . . . . . . . 121
Automatic Temperature Control (ATC) . . . . . . . . . 222
Automatic Transmission . . . . . . . . . . . . . 236,323,324
Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . 324
Fluid and Filter Changes . . . . . . . . . . . . . . . . . 324
Fluid Change . . . . . . . . . . . . . . . . . . . . . . . . . 324
Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . 323
Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
Auxiliary Electrical Outlet (Power Outlet) . . . . . . 160
. . . . . . . . . . . . . . . . . . . 160
Auxiliary Power Outlet

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307

INDEX 375

Emergency Starting . . . . . . . . . . . . . . . . . . . . . 289
Keyless Transmitter Replacement (RKE) . . . . . . . 24
. . . . . . . . . . . . . . . 120
Saving Feature (Protection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
Bearings Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304
Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Body Mechanism Lubrication . . . . . . . . . . . . . . . 311
B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 252
Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 132
Brake Control System, Electronic . . . . . . . . . . . . . 130
Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
. . . . . . . . . . . . . . . . . . . . 131,243