2008 Jeep Compass Owners Manual

storage, insert the regular latch plate into the black button on the top of the mini buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Insert the mini latch plate into the slot provided in the trim panel. Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belts in the event of a collision. These devices improve the performance of the seat belt system by assuring that the belt is tight about the occupant in a collision. Pretensioners work for all size occupants, including those in child restraints. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly.

44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

The pretensioners are triggered by the Airbag Control Module (refer to information on Airbags in this section). Like the front airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced. Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60
seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts. Once the warning is triggered, the Enhanced Warning System (BeltAlert) will continue to chime and flash the Seat Belt Warning Light for 96 seconds or until the driver’s seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h).

The Enhanced Warning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler Corporation does not recommend deactivating the Enhanced Warning Sys- tem (BeltAlert). 1. Turn the ignition switch to the LOCK position and buckle the driver or front passenger seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver or front passenger seat belt at least three times within 10
seconds, ending with the seat belt buckled.

NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming. The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver or front passenger seat belt remains unbuckled.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45

Seat Belt Extender If a seat belt is too short, even when fully extended, and when the adjustable upper shoulder belt anchorage (if so equipped) is in its lowest position, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender, and store it.

WARNING!

Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.

46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove com- partment. The words SRS AIRBAG are embossed on the airbag covers.

Front Airbags and Knee Bolsters

NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity. This vehicle may also be equipped with side curtain airbags to protect the driver and passengers sitting next

to a window. If the vehicle is equipped with side curtain airbags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.

Side Curtain Airbag Location

NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47

WARNING!

† Do not put anything on or around the front airbag covers or

attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.

† If your vehicle is equipped with side curtain airbags, do not

stack luggage or other cargo up high enough to block the location of the side curtain airbag. The area where the side curtain airbag is located should remain free from any obstructions.

† If your vehicle is equipped with side curtain airbags, do not

have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason.

† Do not drill, cut or tamper with the knee bolster in any way. † Do not mount any accessories to the knee bolster such as

alarm lights, stereos, citizens band radios etc.

48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: Do not use a clothing bar mounted to the coat hooks in this vehicle. A clothing bar will impede the proper performance of the curtain airbags. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side Cur- tain Airbags also work with seat belts to improve occu- pant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. If your vehicle is so equipped, the Side Curtain Airbag on the crash side of the vehicle is triggered in moderate to severe side collisions. However, even in collisions where the airbags deploy, you need the seat belts to keep you in the correct position for the airbags to protect you prop- erly.

Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should ride buckled up in the rear seat. 2. Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment could cause severe injury or death to infants in that position. 3. Children that are not big enough to wear the vehicle seat belt properly (refer to information on Child Restraint in this section) should be secured in the rear seat in child restraints or belt-positioning booster seats. 4. Older children who do not use child restraints or belt-positioning booster seats should ride properly buck- led up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm.

5. If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint (refer to information on Child Restraint in this section). 6. You should read the instructions provided with your child restraint to make sure that you are using it properly. 7. All occupants should use their seat belts properly. 8. The driver and front passenger seats should be moved back as far as practical to allow the airbags time to inflate. 9. If your vehicle has side curtain airbags do not lean against the door, airbags will inflate forcefully into the space between you and the door. 10. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided in the 9If You Need Customer Assistance9 section in this manual.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49

WARNING!

† Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. † Being too close to the steering wheel or instrument panel during airbag deployment could cause seri- ous injury. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. † If the vehicle has side curtain airbags, they also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.

50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Air Bag System Components The airbag system consists of the following: † Occupant Restraint Controller (ORC) † Side Remote Acceleration Sensors (If Equipped) † Airbag Warning Light † Driver Airbag † Front Passenger Airbag † Supplemental Side Curtain Airbags above Side Win- † Steering Wheel and Column † Instrument Panel † Interconnecting Wiring † Seatbelt Reminder Light † Knee Impact Bolsters

dows (If Equipped)

† Front Acceleration Sensors † Driver and Front Passenger Seat Belt Pretensioners How The Airbag System Works † The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate. The front airbag inflators are de- signed to provide different rates of airbag inflation from direction provided by the ORC. This ORC will detect roll over. † The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items listed above except the knee bolster, the instru- ment panel, and the steering wheel and column. If the key is in the LOCK position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate.

† The ORC also turns on the Airbag Warning Light in the instrument panel for 6 to 8
seconds as a self-check when the ignition is first turned on. After the self-check, the Airbag Warning Light will turn off. If the ORC detects a malfunction in any part of the system, it turns on the Airbag Warning Light either momentarily or continu- ously. A single chime will sound if the light comes on again after initial start up.

WARNING!

Ignoring the AIRBAG Warning Light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51

† The Driver and Front Passenger Airbag/Inflator Units are located in the center of the steering wheel and the passenger side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different airbag inflation rates may be possible based on colli- sion severity. The steering wheel hub trim cover, and the upper passenger side of the instrument panel separate and fold out of the way, as the bags inflate to their full size. The bags fully inflate in about 50 - 70
milliseconds. This is about half of the time that it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger. The driver’s front airbag gas is vented through vent holes in the sides of the airbag. The passenger’s front airbag gas is vented through vent holes in the sides of the airbag. In this way, the airbags do not interfere with your control of the vehicle.

52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

† The Side Impact SRS Side Curtain Airbag are de- signed to activate only in certain side collisions. When the ORC (with side impact option) detects a collision requiring the side curtain airbag to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the side curtain airbag. The inflating side curtain airbag pushes the outside edge of the headliner out of the way and covers the window. The airbag inflates in about 30
milliseconds (about one quarter of the time that it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the side curtain airbag inflates. This especially applies to children. The side curtain airbag is only about 3-1/2 inches (9 cm) thick when it is inflated. † The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position every- one for the best interaction with the front airbag.

If A Deployment Occurs The airbag system is designed to deploy when the ORC detects a moderate-to-severe collision, to help restrain the driver and front passenger, and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision, which deploys the airbags, any or all of the following may occur: † The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.

However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. † As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instruc- tions for cleaning. † It is not advisable to drive your vehicle after the airbags have been deployed. If you are involved in another collision, the airbags will not be in place to protect you.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53

WARNING!

Deployed airbags can’t protect you in another colli- sion. Have the airbags replaced by an authorized dealer as soon as possible.

Enhanced Accident Response System In the event of an impact that causes airbag deployment, with the vehicle stopped, and the vehicle communication network intact, and the power intact, the Enhanced Accident Response System performs the following func- tions: † Cuts off fuel to the engine. † Flashes hazard lights. † Turns on the interior lamps which remain on as long as the battery has power or until the ignition key is removed.

† Unlocks the doors automatically

54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Maintaining Your Airbag System

WARNING!

† Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper passenger side of the instrument panel. Do not modify the front bumper, vehicle body struc- ture, or frame. † You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee impact bolster. † It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has airbags.

Airbag Warning Light

You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have service the system an authorized dealer promptly: † The Airbag Warning Light does not come on or flickers during the 6 to 8 seconds when the ignition switch is first turned on. † The light remains on or flickers after the 6 to 8 second † The light flickers or comes on and remains on while

interval.

driving.

Event Data Recorder (EDR)

In the event of an accident, your vehicle is designed to record up to 5 - seconds of specific vehicle data param- eters (see list below) in an event data recorder prior to the moment of airbag deployment, or near-deployment, and up to a quarter second of high-speed deceleration data during and/or after air bag deployment or near- deployment. EDR data are ONLY recorded if an airbag deploys, or nearly deploys, and are otherwise unavail- able. NOTE: 1. A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually indica- tive of a crash, but not severe enough to warrant airbag deployment. 2. Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power).

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55

to

crash

initiated

investigations

In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by DaimlerChrysler and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance. In addition by DaimlerChrysler, such investigations may be requested by customers, insurance carriers, government officials, and professional crash researchers, such as those associ- ated with universities, and with hospital and insurance organizations. In the event that an investigation is undertaken by DaimlerChrysler (regardless of initiative), the company or its designated representative will first obtain permis- sion of the appropriate custodial entity for the vehicle (usually the vehicle owner or lessee) before accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be provided to the

56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially. Confidential data will not be dis- closed by DaimlerChrysler to any third party except when: 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved 2. Used DaimlerChrysler product 3. Requested by police under a legal warrant 4. Otherwise required by law

involving

litigation

defense

of

in

Data Parameters that May Be Recorded: † Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system

cycles and vehicle mileage)

† Airbag disable lamp status (if equipped) † 9Time9 of airbag deployment (in terms of ignition † Airbag deployment level (if applicable) † Impact acceleration and angle † Seatbelt status † Brake status (service and parking brakes) † Accelerator status (including vehicle speed) † Engine control status (including engine speed) † Transmission gear selection

† Cruise control status † Traction/stability control status † Tire pressure monitoring system status Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buck- led up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats, rather than in the front.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57

WARNING!

In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.

Infants And Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child:

58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

† Safety

experts

recommend that

children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and 9convertible9 child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt or the LATCH child restraint anchorage system. † The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). 9Convertible9 child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 9 kg (20 lbs) but are less than one year old.

† Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. † Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. † The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s cushion while the child’s back is against the seat back; they should use a Belt Positioning Booster Seat. The child and booster seat are held in the vehicle by the lap/

shoulder belt. (Some booster seats are equipped with a front shield and are held in the vehicle by the lap portion.)

NOTE: www.seatcheck.org.

For

additional

information

refer

to

WARNING!

† Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. † A rearward facing child restraint should only be used in a rear seat. A rearward facing child re- straint in the front seat may be struck by a deploy- ing passenger airbag which may cause severe or fatal injury to the infant.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59

Here are some tips on getting the most out of your child restraint: † Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it. † The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. † Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. The passenger seat belts are equipped with either cinching latch plates or seat belt retractors that can be switched to an automatic locking mode, which are designed to keep the lap portion tight around the child

60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary.

If the seat belt has a switchable retractor, it will have a distinctive label. To operate the switchable retractor, please refer to Automatic-Locking Retractor (ALR) in this section. † In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle end of the belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out.

† If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. † Buckle the child into the seat according to the child † When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury.

restraint manufacturer’s directions.

Automatic-Locking Retractor (ALR) To operate the switchable retractor, pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then pull on the belt until it is all removed from the retractor. Allow the belt to return into the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. Follow the instructions of the child restraint manufacture. NOTE: To reset this feature you must let all of the belt webbing return into the retractor. You will not be able to pull out more webbing until all of the webbing has been returned back into the retractor.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61

Lower Anchors and Tether for CHildren (LATCH) Your vehicle is equipped with the child restraint anchor- age system called LATCH, which stands for Lower Anchors and Tether for CHildren. The LATCH system provides for the installation of the child restraint without using the vehicle seat belt. All three rear seating positions have lower anchorages that are capable of accommodat- ing LATCH-compatible child seats having flexible, webbing-mounted lower attachments. Child seats with fixed lower attachments must be installed in the out- board positions only. Regardless of the specific type of lower attachment, NEVER install LATCH-compatible child seats such that two seats share a common lower anchorage. If you are installing LATCH-compatible child restraints in adjacent rear seating positions, you can use the LATCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not

62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

LATCH-compatible, you can only install the child re- straints using the vehicle’s seat belts. Please refer to, Installing the Child Restraint System for typical installa- tion instructions.

Rear Seat LATCH

Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt. They will also have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle.

NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63

Installing the Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector and a means for adjusting the tension in the strap. Forward-facing toddler restraints and some rearward-facing infant restraints will also be equipped with a tether strap with a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the

64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

rear of the seat back. Then tighten all three straps as you push the child restraint rearward and downward into the seat.

Rear Seat Tether Anchors

Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system.

If your child restraint seat is not LATCH com- NOTE: patible, install the restraint using the vehicle seat belts.

WARNING!

An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap.

Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat. † Make sure that the child is upright in the seat.

as possible.

† The lap portion should be low on the hips and as snug † Check belt fit periodically. A child’s squirming or † If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.

slouching can move the belt out of position.

Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65

ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55
mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided. The engine oil installed in the engine at the factory is a high quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. The recommended viscosity and quality grades are shown in Section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.

66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty.

SAFETY TIPS

Exhaust Gas

WARNING!

Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.

Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.

If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed.

WARNING!

If you are required to drive with the deck lid / liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.

Safety Checks You Should Make Inside The Vehicle

Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.

Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc. If there is any question regarding belt or retractor condition, replace the belt. Airbag Light The light should come on and remain on for 6 to 8
seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked. If the light stays on or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67

Periodic Safety Checks You Should Make Outside The Vehicle

Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (includ- ing spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil or other fluid leaks. Also, if gasoline fumes are detected or fuel, power steering fluid, trans- mission fluid or brake fluid leaks are suspected, the cause should be located and corrected immediately.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CONTENTS

m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
N Inside Day/Night Mirror — If Equipped . . . . . .73
N Outside Mirror—Driver’s Side . . . . . . . . . . . . .73
N Outside Mirror—Passenger’s Side . . . . . . . . . . .74
N Power Remote Control Mirrors —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .74
N Vanity Mirrors — If Equipped . . . . . . . . . . . . .76
N Sun Visor Sliding Feature . . . . . . . . . . . . . . . .76

m Hands–Free Communication (UConnect™) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

N Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
N Phone Call Features . . . . . . . . . . . . . . . . . . . .85
N UConnect™ System Features . . . . . . . . . . . . . .88
N Advanced Phone Connectivity . . . . . . . . . . . . .93
N Things You Should Know About Your

UConnect™ System . . . . . . . . . . . . . . . . . . . . .95
N General Information . . . . . . . . . . . . . . . . . . . 103
m Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
N Front Seat Adjustment . . . . . . . . . . . . . . . . . . 103

70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

N Manual Seat Height Adjustment —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 104
N Manual Lumbar— If Equipped . . . . . . . . . . . . 105
N Driver’s Seat Back Recline . . . . . . . . . . . . . . . 105
N Adjustable Head Restraints . . . . . . . . . . . . . . 106
N Heated Seats — If Equipped . . . . . . . . . . . . . 107
N Fold Flat Front Passenger Seat . . . . . . . . . . . . 108
N Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . 109
N Reclining Rear Seat — If Equipped . . . . . . . . . 110
m To Open And Close The Hood . . . . . . . . . . . . . 112
m Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
N Map/Reading Lights . . . . . . . . . . . . . . . . . . . 113
N Multi-Function Control Lever . . . . . . . . . . . . . 114

N Headlights, Parking Lights, Instrument Panel

Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

N Daytime Running Lights (DRL) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 115
N Lights-On Reminder . . . . . . . . . . . . . . . . . . . 115
N Fog Lights — If Equipped . . . . . . . . . . . . . . . 116
N Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 116
N Highbeam/Lowbeam Select Switch . . . . . . . . . 117
N Passing Light . . . . . . . . . . . . . . . . . . . . . . . . 118
N Off-Road Lights – If Equipped . . . . . . . . . . . . 118
m Windshield Wipers And Washers . . . . . . . . . . . 119
N Windshield Washers . . . . . . . . . . . . . . . . . . . 119
N Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . . 120
N Windshield Wiper Operation . . . . . . . . . . . . . 121

N Intermittent Wiper System . . . . . . . . . . . . . . . 122
N Adding Washer Fluid . . . . . . . . . . . . . . . . . . 122
m Tilt Steering Column . . . . . . . . . . . . . . . . . . . . 122
m Electronic Speed Control — If Equipped . . . . . . 123
N To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 123
N To Set At A Desired Speed . . . . . . . . . . . . . . . 124
N To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . 124
N To Resume Speed . . . . . . . . . . . . . . . . . . . . . 124
N To Vary The Speed Setting . . . . . . . . . . . . . . . 124
N Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 125
N To Accelerate For Passing . . . . . . . . . . . . . . . 125
m Anti-Lock Brake System (ABS) – If Equipped . . . 126

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71

m Electronic Brake Control System –

ABS/TCS/BAS/ERM/ESP . . . . . . . . . . . . . . . . 127
N Anti-Lock Brake System – (ABS) . . . . . . . . . . . 127
N Traction Control System (TCS) . . . . . . . . . . . . 127
N Brake Assist System (BAS) . . . . . . . . . . . . . . . 128
N Electronic Roll Mitigation (ERM) . . . . . . . . . . 129
N ESP (Electronic Stability Program) . . . . . . . . . 130
m Garage Door Opener — If Equipped . . . . . . . . . 134
N Programming HomeLinkt . . . . . . . . . . . . . . . 135
N Gate Operator/Canadian Programming . . . . . 138
N Using HomeLinkt . . . . . . . . . . . . . . . . . . . . . 139
N Reprogramming a Single HomeLinkt Button . . 139
N Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

N Troubleshooting Tips . . . . . . . . . . . . . . . . . . . 140
N General Information . . . . . . . . . . . . . . . . . . . 140
m Power Sunroof — If Equipped . . . . . . . . . . . . . 141
N Opening The Sunroof . . . . . . . . . . . . . . . . . . 142
N Closing The Sunroof . . . . . . . . . . . . . . . . . . . 142
N Pinch Protect Feature . . . . . . . . . . . . . . . . . . . 143
N Pinch Protect Override . . . . . . . . . . . . . . . . . 143
N Venting Sunroof – Express . . . . . . . . . . . . . . . 143
N Sunshade Operation . . . . . . . . . . . . . . . . . . . 143
N Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 143
N Sunroof Maintenance . . . . . . . . . . . . . . . . . . . 144
N Ignition Off Operation . . . . . . . . . . . . . . . . . . 144
m Electrical Power Outlets — If Equipped . . . . . . . 144

N Electrical Outlet Use With Engine Off . . . . . . . 146
m Console Features . . . . . . . . . . . . . . . . . . . . . . . 147
m Cargo Area Features . . . . . . . . . . . . . . . . . . . . . 148

N Cargo Light/Removable Self Recharging

Flashlight – If Equipped . . . . . . . . . . . . . . . . 148
N Cargo Cover — If Equipped . . . . . . . . . . . . . . 150
N Removable Load Floor . . . . . . . . . . . . . . . . . . 150
N Cargo Tie-Down Loops . . . . . . . . . . . . . . . . . 151
N Fold Down Speakers – If Equipped . . . . . . . . . 152
m Rear Window Features . . . . . . . . . . . . . . . . . . . 152
N Rear Window Wiper/Washer . . . . . . . . . . . . . 152
N Rear Window Defroster . . . . . . . . . . . . . . . . . 153
m Roof Luggage Rack — If Equipped . . . . . . . . . . 154

MIRRORS

Inside Day/Night Mirror — If Equipped Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73

Adjusting Rear View Mirror

Outside Mirror—Driver’s Side Adjust the Flat (Drivers Side) Outside Mirror so you can just see the side of your vehicle in the part of the mirror closest to vehicle with your head close to the door glass.

74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Outside Mirror—Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the center of the vehicle.

WARNING!

Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror.

Power Remote Control Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel.

Remote Control Mirrors Switch

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75

WARNING!

Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror.

Mirror Directions

To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror.

76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Vanity Mirrors — If Equipped To use the mirror, rotate the sun visor down and swing the mirror cover upward.

Sun Visor Sliding Feature The sun visors may be pulled out to provide extended coverage of the side glass.

HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., 9Call” { “Mike” {”Work9 or 9Dial” { “248-555-12129). Your cellular phone’s audio is trans- mitted through your vehicle’s audio system; the system will automatically mute your radio when using the UConnect™ system. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth 9Hands-Free Profile,9
version 0.96 or higher. See UConnect™ website for sup- ported phones.

Vanity Mirror

NOTE: For UConnect™ customer support, visit the following web sites: † www.chrysler.com/uconnect † www.dodge.com/uconnect † www.jeep.com/uconnect † or call 1–877–855–8400
UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The UConnect™ phone book enables you to store up to 32 names and four numbers per name. Each language has

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77

a separate 32-name phone book accessible only in that language. This system is driven through your Blue- tooth™ Hands-Free profile cellular phone. UConnect™ features Bluetooth™ technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so UCon- nect works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnect™ system. The UConnect™ system allows up to seven cellular phones to be linked to system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages (as equipped).

78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Phone Button

The rearview mirror contains the microphone for the system (depending on the type of mirror and radio equipped), and either the radio or the mirror has the two control buttons (Phone Button and Voice Recognition Button) that will enable you to access the system. Voice Recognition Button

Actual button location may vary with radio. The individual buttons are described in the “Operation” section.

The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See UConnect™ website for supported phones. If your cellu- lar phone supports a different profile (e.g., Headset

Profile) you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details. The UConnect™ system is fully integrated with the vehicle’s audio system. The volume of the UConnect™ system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect™ system such as 9CELL9 or caller ID on certain radios. Operation Voice commands can be used to operate the UConnect™ system and to navigate through the UConnect™ menu structure. Voice commands are required after most UConnect™ system prompts. You will be prompted for a specific command and then guided through the available options.

† Prior to giving a voice command, one must wait for the beep, which follows the 9Ready9 prompt or another prompt. † For certain operations, compound commands can be used. For example, instead of saying 9Setup9 and then 9Phone Pairing,9 the following compound command can be said: 9Setup Phone Pairing.9
† For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command, when you are asked for it. For example, you can use the combined form voice com- mand 9Phonebook New Entry,9 or you can break the combined form command into two voice commands: 9Phonebook9 and 9New Entry.9 Please remember, the UConnect™ system works best when you talk in a normal conversational tone, as if speaking to some one sitting eight feet away from you.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79

Voice Command Tree Refer to “Voice Tree” at the end of this section. Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say 9Help9 following the beep. The UConnect™ system will play all the options at any prompt if you ask for help. To activate the UConnect™ system from idle, simply press the “Phone” button and follow audible prompts for directions. All UConnect™ system sessions begin with a press of the “Phone” button on the radio control head. Cancel Command At any prompt, after the beep, you can say 9Cancel9 and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu.

80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Pair (Link) UConnect™ System to a Cellular Phone To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone. To complete the pairing process, you will need to reference your cellular phone owner’s manual. The UConnect™ website may also provide detailed instructions for pairing. The following are general phone to UConnect™ System pairing instructions: † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † When prompted, after the beep, say 9Pair a Phone9 and † You will be asked to say a four-digit pin number, which you will later need to enter into your cellular. You can enter any four-digit pin number. You will not need to remember this pin number after the initial pairing process.

follow the audible prompts.

9Setup Phone Pairing.9

† For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. † You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to your UConnect™ system. However, at any given time, only one cellular phone can be in use, connected to your UConnect™ System. The priority allows the UConnect™ system to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority 3 and priority 5
phones are present in the vehicle, the UConnect™ system will use the priority 3 cellular phone when you make a call. You can select to use a lower priority cellular phone at any time (refer to 9Advanced Phone Connectivity9).

call.

9Dial.9

Dial by Saying a Number † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † System will prompt you to say the number you want † For example, you can say 9234-567-8901.9 The phone number that you enter must be of valid length and combination. Based on the country in which the ve- hicle was purchased, the UConnect™ limits the user from dialing invalid combination of numbers. For example, in USA, 234-567-890 is nine digits long, which is not a valid USA phone number - the closest valid phone number has ten digits. † The UConnect™ system will confirm the phone num- ber and then dial. The number will appear in the display of certain radios.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81

“Call.9

you want call.

Call by Saying a Name † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † System will prompt you to say the name of the person † After the 9Ready9 prompt and the following beep, say the name of the person you want to call. For example, you can say 9John Doe,9 where John Doe is a previ- ously stored name entry in the UConnect™ phone book. Refer to 9Add Names to Your UConnect™ Phonebook,9 to learn how to store a name in the phone book. † The UConnect™ system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios.

82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

9Phonebook New Entry.9

Add Names to Your UConnect™ Phonebook NOTE: Adding names to phone book is recommended when vehicle is not in motion. † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † When prompted, say the name of the new entry. Use of long names helps the voice recognition and it is recommended. For example, say 9Robert Smith9 or 9Robert9 instead of 9Bob.9
† When prompted, enter the number designation (e.g., 9Home,9 9Work,9 9Mobile,9 or 9Pager9). This will allow you to store multiple numbers for each phone book entry, if desired. † When prompted, recite the phone number for the

phone book entry that you are adding.

After you are finished adding an entry into the phone book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The UConnect™ system will allow you to enter up to 32
names in the phone book with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phone book accessible only in that language. Phonebook Download UConnect™ allows the user to download entries from their phone via Bluetooth. To use this feature, press the “Phone” button and say “Phonebook Download.” Sys- tem prompts “Ready to accept vcard entry via Blue- tooth…” The system is now ready to accept phonebook entries from your phone using the Bluetooth Object

fers of phonebook entries to use this feature.

Exchange Profile (OBEX). Please see your phone owners’ manual for specific instructions on how to send these entries from your phone. NOTE: † Phone handset must support Bluetooth OBEX trans- † Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth, and you may see a message on the phone display that the Bluetooth link is busy. In this case, the user must first disconnect or drop the Bluetooth connection to the UConnect™ and then send the address book entry via Bluetooth. Please see your phone owners’ manual for specific instructions on how to drop the Bluetooth connection. † If the phonebook entry is longer than 24 characters it

will be use only the first 24 characters.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83

Edit Entries in the UConnect™ Phonebook NOTE: Editing names in the phone book is recom- mended when vehicle is not in motion. † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † You will then be asked for the name of the phone book † Next, choose the number designation (home, work, † When prompted, recite the new phone number for the

mobile, or pager) that you wish to edit.

entry that you wish to edit.

9Phonebook Edit.9

phone book entry that you are editing.

After you are finished editing an entry in the phone book, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.

84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

9Phonebook Edit9 can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later using the 9Phonebook Edit9 feature. Delete Entries in the UConnect™ Phonebook NOTE: Editing phone book entries is recommended when vehicle is not in motion. † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phone book entry that you wish to delete or you can say 9List Names9 to hear a list of the entries in the phone book from which you choose. To select one of the entries

9Phonebook Delete.9

from the list, press the 9Voice Recognition9 button while the UConnect™ system is playing the desired entry and say 9Delete.9
† After you enter the name, the UConnect™ system will ask you which designation you wish to delete, home, work, mobile, pager, or all. Say the designation you wish to delete. † Note that only the phone book entry in the current

language is deleted.

Delete All Entries in the UConnect™ Phonebook † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † The UConnect™ system will ask you to verify that you

9Phonebook Erase All.9

wish to delete all the entries from the phonebook.

† After confirmation, the phone book entries will be † Note that only the phone book in the current language

deleted.

is deleted.

9Phonebook List Names.9

List All Names in the UConnect™ Phonebook † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † The UConnect™ system will play the names of all the † To call one of the names in the list, press the 9Voice Recognition’ button during the playing of the desired name, and say 9Call.9

phone book entries.

NOTE: The user can also exercise 9Edit9 or 9Delete9
operations at this point.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85

† The UConnect™ system will then prompt you as to the number designation you wish to call. † The selected number will be dialed. Phone Call Features The following features can be accessed through the UCon- nect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be ac- cessed through the UConnect™ system. Check with your cellular service provider for the features that you have. Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will the vehicle audio system, if on, and will ask if you would like to answer the call. Press ’Phone’ button to accept the call. To reject the call, press and hold the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected.

interrupt

86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the ’Phone’ button to place the current call on hold and answer the incoming call. NOTE: The UConnect™ system compatible phones in market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only either answer an incoming call or ignore it. Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say 9Dial9 or 9Call9 followed by the phone number or phone book entry you wish to call. The first call will be on hold while

the second call is in progress. To go back to the first call, refer to 9Toggling Between Calls.9 To combine two calls, refer to 9Conference Call.9
Place/Retrieve a Call from Hold To put a call on hold, press the 8Phone’ button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the “Phone” button until you hear a single beep. Toggling Between Calls If two calls are in progress (one active and one on hold), press the “Phone” button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.

Conference Call When two calls are in progress (one active and one on hold), press and hold the “Phone” button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-Way Calling To initiate three-way calling, press the “Voice Recogni- tion” button while a call is in progress and make a second phone call as described under 9Making a Second Call while Current Call in Progress.9 After the second call has established, press and hold the “Phone” button until you hear a double beep indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, momentarily press the “Phone” button. Only the active call(s) will be terminated and if

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87

there is a call on hold, it will become the new active call. If the active call is terminated by the far end, a call on hold may not become active automatically. This is cell phone dependent. To bring the call back from hold, press and hold the “Phone” button until you hear a single beep. Redial † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † The UConnect™ system will call the last number that

9Redial.9

was dialed on your cellular phone.

NOTE: This may not be the last number dialed from the UConnect™ system.

88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Call Continuation Call continuation is progression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off. Call continuation functionality available on the vehicle can be any one of three types: † After ignition key is switched off, a call can continue on the UConnect™ system either until the call ends or until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. † After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred from the UConnect™ system to the mobile phone.

† An active call

is automatically transferred to the

mobile phone after ignition key is switched to off.

UConnect™ System Features

Language Selection To change the language that the UConnect™ system is using, † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). † Continue to follow the system prompts to complete

language selection.

After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every UConnect™ language change op- eration, only the language specific 32-name phone book is usable. The paired phone name is not language specific and usable across all languages.

Emergency Assistance If you are in an emergency and the mobile phone is reachable: † Pick up the phone and manually dial the emergency

number for your area.

If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say 9Emergency9 and the UConnect™ system will instruct the paired cellular phone to call the emergency num- ber. This feature is only supported in the USA.

NOTE: The emergency number dialed is based on the Country where the vehicle is purchased (911 for USA and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89

The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly. Your phone must be turned on and paired to the UCon- nect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. Towing Assistance If you need towing assistance, † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say

9Towing Assistance.9

NOTE: The Towing Assistance number dialed is based on the Country where the vehicle is purchased (1-800- 528-2069 for USA, 1-877-213-4525 for Canada, 55-14-3454
for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico).

90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Please refer to the 24-Hour “Towing Assistance” cover- age details in the Warranty information booklet and on the 24–Hour Towing Assistance Card. Paging To learn how to page refer to 9Working with Automated Systems.9 Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to 9Working with Automated Systems.9
Working with Automated Systems This method is designed to be used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated tele- phone system.

You can use your UConnect™ system to access a voice- mail system or an automated service, such as, paging service or automated customer service. Some services require immediate response selection, in some instances, that may be too quick for use of UConnect™ system. When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the “Voice Recognition” button and say the sequence you wish to enter followed by the word 9Send.9 For example, if required to enter your pin number followed with a pound 3 7 4 6 #, you can press the “Voice Recognition” button and say 93 7 4 6 # Send.9 Saying a number, or sequence of numbers, followed by 9Send9 is also to be used to navigate through an automated customer service center menu structure and to leave a number on a pager.

You can also send stored UConnect™ phonebook entries as tones for fast and easy access to voicemail and pager entries. To use this feature, dial the number you wish to call and then press the “Voice Recognition” button and say “Send.” The system will prompt you to enter the name or number, say the name of the phonebook entry you wish to send. The UConnect™ will then send the corresponding phone number associated with the phone- book entry as tones over the phone. NOTE: † You may not hear all of the tones due to cellular phone † Some paging and voicemail systems have system timeout settings too short that may not allow the use of this feature.

network configurations, this is normal.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91

Barge In - Overriding Prompts The “Voice Recognition” button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing 9Would you like to pair a phone, clear a{,9 you could press the “Voice Recognition” button and say 9Pair a Phone9 to select that option without having to listen to the rest of the voice prompt. Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g., the UConnect™ system will not repeat a phone number before you dial it). † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say 9Setup Confirmations.9 The UConnect™ system will play the current confirmation prompt status and you will be given the choice to change it.

92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Phone and Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your cell phone, the UConnect™ system will provide notification to inform you of your phone and network status when you are attempting to make a phone call using UConnect™. The status is given for roaming, network signal strength, phone battery strength, etc. Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s audio system. The UConnect™ system will work the same as if you dial the number using voice recognition.

NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect™ system to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number, the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio. Mute/Un-Mute (Mute Off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect™ system: † Press the “Voice Recognition” button. † Following the beep, say 9Mute.9
In order to un-mute the UConnect™ system: † Press the “Voice Recognition” button. † Following the beep, say 9Mute-off.9

Advanced Phone Connectivity

Transfer Call to and from Cellular Phone The UConnect™ system allows on going calls to be transferred from your cellular phone to the UConnect™ system without terminating the call. To transfer an ongo- ing call from your UConnect™ paired cellular phone to the UConnect™ system or vice-versa, press the “Voice Recognition” button and say 9Transfer Call.9
Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively 9connected9
with one electronic device at a time. If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, then follow the instruction described in your cellular phone user’s manual.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93

“Setup Phone Pairing.”

List Paired Cellular Phone Names † Press the “Phone” button to begin. † After the “Ready” prompt and the following beep, say † When prompted, say 9List Phones.9
† The UConnect™ system will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the “Voice Recogni- tion” button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” or “delete” a paired phone.

94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

9Setup Select Phone9 and follow the prompts.

Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † You can also press the “Voice Recognition” button anytime while the list is being played, and then choose the phone that you wish to select. † The selected phone will be used for the next phone call. If the selected phone is not available, the UCon- nect™ system will return to using the highest priority phone present in or near (approximately within 30
feet) the vehicle.

9Setup Phone Pairing.9

Delete UConnect™ Paired Cellular Phones † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † At the next prompt, say 9Delete9 and follow the † You can also press the “Voice Recognition” button anytime while the list is being played, and then choose the phone you wish to delete.

prompts.

Things You Should Know About Your UConnect™ System

UConnect™ Tutorial To hear a brief tutorial of the system features, press the “Phone” button and say “UConnect™ Tutorial.” Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, the UCon- nect™ system Voice Training feature may be used. To enter this training mode, follow one of the two proce- dures: From outside the UConnect™ mode (e.g. from radio mode) † Press and hold the “Voice Recognition” button for 5
† Press the “Voice Recognition” button and say 9Setup,

seconds until the session begins, or,

Voice Training9 command.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95

Repeat the words and phrases when prompted by the UConnect™ system. For best results, the Voice Training session should be completed when the vehicle is parked, engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. To restore the Voice Recognition system to factory default settings, enter the Voice Training session via the above procedure and follow the prompts. Voice Recognition (VR) † For best performance, adjust the rear view mirror to provide at least 1⁄2 inch (1 cm) gap between the overhead console (if equipped) and the mirror.

† Always wait for the beep before speaking. † Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you.

96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

† Make sure that no one other than you is speaking during a voice recognition period. † Performance is maximized under: † low-to-medium blower setting, † low-to-medium vehicle speed, † low road noise, † smooth road surface, † fully closed windows, † dry weather condition. † Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some. † When navigating through an automated system, such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say 9Send.9

motion is recommended.

names in the UConnect™ phone book.

† Storing names in phone book when vehicle is not in † It is not recommended to store similar sounding † UConnect™ phone book nametag recognition rate is optimized for the person who stored the name in the phone book. † You can say 9O9 (letter 9O9) for 909 (zero). 98009 must be † Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. † In a convertible vehicle, system performance may be

spoken 9eight-zero-zero.9

compromised with the convertible top down.

Far End Audio Performance † Audio quality is maximized under: † low-to-medium blower setting, † low-to-medium vehicle speed, † low road noise, † smooth road surface, † fully closed windows, and † dry weather condition. † operation from driver seat. † Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect™ system.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97

† Echo at far end can sometime be reduced by lowering † In a convertible vehicle, system performance may be

the in-vehicle audio volume.

compromised with the convertible top down.

Bluetooth Communication Link Cellular phones have been found to lose connection to the UConnect™ system. When this happens, the connec- tion can generally be re-established by switching the phone off/on. Your cell phone is recommended to remain in Bluetooth 9on9 mode. Power-Up After switching the ignition key from OFF to either ON or ACC position, or after a language change, you must wait at least five (5) seconds prior to using the system.

98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99

100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Voice Commands

Alternate(s)

Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101

Voice Commands

Alternate(s)

Primary call cancel confirmation prompts. continue delete dial download edit emergency English erase all Espanol Francais help home

102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Voice Commands

Alternate(s)

pairing phone book

Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial

Voice Commands

Alternate(s) return or main menu select

phone settings or phone set up

Primary return to main menu select phone send set up

towing assistance transfer call UConnect™ Tutorial try again voice training work yes

General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: † This device may not cause harmful interference. † This device must accept any interference received, including interference that may cause undesired op- eration.

SEATS

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103

Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position.

Front Seat Adjustment

Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.

Manual Seat Height Adjustment — If Equipped The driver’s seat height can be raised or lowered by using the ratcheting handle on the outboard side of the seat to adjust the driving position.

104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

† Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. † Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.

Seat Height Adjustment

Manual Lumbar— If Equipped The Lumbar adjustment is located on the outboard side of the driver’s seat. To increase or decrease support, rotate the handle up or down.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105

Driver’s Seat Back Recline To recline: 1. Lean forward before lifting the handle, then lean back to the desired position and release the handle. 2. Lift the handle to return the seatback to an upright position.

Lumbar Adjustment

Reclining Seat

106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraints so that the upper edge is as high as practical. To raise the head restraint, pull up on the head restraint. To lower the head restraint, depress the button and push down on the head restraint.

Head Restraint Adjustment

Heated Seats — If Equipped

WARNING!

Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat.

This feature heats the front driver’s and passenger’s seats. The controls for the heater is located on the instrument panel, below the radio. After turning on the

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107

ignition, you may choose OFF, HIGH, or LOW heat settings. An indicator on the switch shows which setting has been chosen.

Heated Seat Switches

† Pressing the switch once will select high- level heating.

† Pressing the switch a second time will select low-level heating. Pressing the switch a third time will shut the heating elements off.

Fold Flat Front Passenger Seat

108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

When high-temperature heating is selected, the heaters provide a boosted heat level during the first four minutes of operation after heating is activated. The heat output then drops to the normal high-temperature level. If high-level heating is selected, the system will automati- cally switch to the low level after about 30 minutes of continuous operation. At that time, the number of illu- minated LEDs changes from two to one, indicating the change. Operation on the low setting also turns off automatically after about 30 minutes. NOTE: felt within 2 to 3 minutes.

If the high heat setting is selected, heat will be

Fold Flat Front Passenger Seat Control

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109

Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward. Pull the strap forward to move the seat forward and flat.

Front Passenger Seat Folded Flat

Folding Rear Seat

110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Reclining Rear Seat — If Equipped

Rear Seat Folded Flat

Rear Seat Recline Pull

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111

For additional comfort, pull the strap forward just enough to release the seatback latch. Then push the seatback to a reclined position, approximately 35 degrees maximum, and release the strap.

WARNING!

† It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. † Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts † Be sure that everyone in your vehicle is in a seat

and using a seat belt properly.

Reclining The Rear Seat

112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located on the left kick panel.

Primary Hood Latch

Then move the safety catch located under the front edge of the hood, near the center and raise the hood.

Secondary Hood Latch

Lift the hood prop rod, clipped to the right side (left side facing hood) of the engine compartment, to secure the hood in the open position. Place the hood prop at the location stamped into the inner hood surface.

To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 20
cm (8 inches) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.

WARNING!

If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113

LIGHTS

Map/Reading Lights These lights are mounted between the sun visors above the rear view mirror. Each light is turned ON by pressing the button. Press the button a second time to turn the light OFF. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the second detent.

Map/Reading Lights

114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically. Multi-Function Control Lever The Multi-Function Control Lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and fog lights. The lever is located on the left side of the steering column. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation. Turn to the second detent for headlight operation.

Headlight Control

To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115

Daytime Running Lights (DRL) — If Equipped The high beam lights will come on as Daytime Running Lights (DRL) at DRL intensity (lower), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the gear shift is in any position except park. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound to alert the driver when the driver’s door is opened.

Dimmer Control

116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Fog Lights — If Equipped

NOTE: The fog lights will only operate with the head- lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals

Front Fog Lights Control

The front fog light switch is on the Multi-Function Control Lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the control lever.

Turn Signal Control

Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent. If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117

Highbeam/Lowbeam Select Switch

High Beam Control

Push the Multi-Function Control Lever away from you to switch the headlights to HIGH beam. Pull the Lever toward you, to switch the headlights back to Low beam.

118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Passing Light You can signal another vehicle with your headlights by lightly pulling the Multi-Function Control Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. If the Multi-Function Control Lever is held in NOTE: the flash to pass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds for the next flash to pass operation.

Off-Road lights – If equipped

CAUTION!

The auxiliary lights mounted on the front bumper should be illuminated during “Off-Road Use Only”. Having them illuminated on public streets, high- ways, roads, etc. may be illegal in your state. Your state may also require auxiliary lights to be covered when operating your vehicle on public streets, high- ways, roads, etc. Further illuminating these lights with supplied covers installed could cause perma- nent damage to the lamps or covers. Before using these auxiliary lights, contact your State Authorities for proper operation and use of these lights.

The auxiliary Off-Road lights can be turned on by pressing the top of the switch when Off-Road conditions require additional lighting. To turn off the auxiliary lights press the bottom of the switch.

WINDSHIELD WIPERS AND WASHERS

The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119

Windshield Washers