Login- Download PDF Manual
-
torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. Airbag Warning Light The light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an autho- rized dealer.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer is inoperable. Periodic Safety Checks You Should Make Outside the Vehicle
for service if your defroster
Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure.
Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CONTENTS
䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 82
▫ Automatic Dimming Mirror — If Equipped . . . 82
▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 83
▫ Exterior Mirrors Folding Feature . . . . . . . . . . 83
▫ Outside Automatic Dimming Mirrors— If Equipped . . . . . . . . . . . . . . . . . . . . . . . 84
▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . . 84
▫ Heated Mirrors — If Equipped . . . . . . . . . . . . 84▫ Illuminated Vanity Mirrors — If Equipped . . . 85
▫ Sun Visor Extension — If Equipped . . . . . . . . 85
䡵 uconnect™ phone — If Equipped . . . . . . . . . . . 85
䡵 Voice Recognition (VR) System — If Equipped . . 85
䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
▫ Front Manual Seat Adjustment . . . . . . . . . . . . 86
▫ Front Seat Adjustment — Recline . . . . . . . . . . 86
▫ Manual Lumbar Support Adjustment . . . . . . . 87
▫ Eight–Way Driver’s Power Seat . . . . . . . . . . . 8878 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
▫ Four-Way Passenger’s Power Seat
— If Equipped . . . . . . . . . . . . . . . . . . . . . . . 88
▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . . 89
▫ Front Heated Seats — If Equipped . . . . . . . . . 90
▫ Rear Heated Seats — If Equipped . . . . . . . . . . 91
▫ 40/20/40 Second Row Folding Seat . . . . . . . . 93
▫ 50/50 Third Row Folding Seat— If Equipped . . . . . . . . . . . . . . . . . . . . . . . 97
䡵 Driver Memory Seat — If Equipped . . . . . . . . . 98▫ Setting Memory Positions And Linking
Remote Keyless Entry Transmitter To Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
▫ Memory Position Recall . . . . . . . . . . . . . . . . 100
▫ To Disable a RKE Transmitter Linked ToMemory . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
▫ Easy Entry/Exit Seat . . . . . . . . . . . . . . . . . . 102
䡵 To Open And Close The Hood . . . . . . . . . . . . 103
䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
. . . . . . . . . . . . . . . . . . 104
. . . . . . . . . . 105▫ Multifunction Lever ▫ Headlights And Parking Lights ▫ Automatic Headlight System
— If Equipped . . . . . . . . . . . . . . . . . . . . . . 105
▫ Headlights On Automatically With Wipers . . 106
▫ Smartbeam™ — If Equipped . . . . . . . . . . . . 106
▫ Automatic Headlight Leveling — HIDHeadlights Only . . . . . . . . . . . . . . . . . . . . . 107
▫ Daytime Running Lights — If Equipped . . . . 108
▫ Fog Lights — If Equipped . . . . . . . . . . . . . . 108
▫ Instrument Panel And Interior Lights . . . . . . 109▫ Battery Saver Feature — Exterior/Interior
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . 110
▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . 110
▫ Lane Change Assist . . . . . . . . . . . . . . . . . . . . 111
▫ High/Low Beam Switch . . . . . . . . . . . . . . . . 111
▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . . 111
▫ Headlight Off Delay . . . . . . . . . . . . . . . . . . . 111
▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . . 111
▫ Courtesy/Reading Lights . . . . . . . . . . . . . . . 111
. . . . . . . . . . 112
▫ Windshield Wiper Operation . . . . . . . . . . . . 113
▫ Windshield Washer Operation . . . . . . . . . . . 113䡵 Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79
▫ Mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
▫ Intermittent Wiper System . . . . . . . . . . . . . . 114
▫ Rain Sensing Wipers — If Equipped . . . . . . . 115
䡵 Tilt/Telescoping Steering Column . . . . . . . . . . 117
䡵 Adjustable Pedals — If Equipped . . . . . . . . . . 117
䡵 Electronic Speed Control — If Equipped . . . . . 119
▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 120
▫ To Set a Desired Speed . . . . . . . . . . . . . . . . 120
▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . 121
▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 121
▫ To Vary The Speed Setting . . . . . . . . . . . . . . 121
▫ To Accelerate For Passing . . . . . . . . . . . . . . 12180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Rear Park Assist — If Equipped . . . . . . . . . . . 122
▫ Rear Park Assist Sensors . . . . . . . . . . . . . . . 122
▫ Rear Park Assist Warning Display . . . . . . . . 123
▫ Enable/Disable The Rear Park Assist . . . . . . 124
▫ Service The Rear Park Assist . . . . . . . . . . . . 125
▫ Cleaning The Rear Park Assist . . . . . . . . . . . 125
▫ System Usage Precautions . . . . . . . . . . . . . . 125
䡵 Rear Camera — If Equipped . . . . . . . . . . . . . . 128▫ Turning The Rear Camera On Or Off — With
Navigation Radio . . . . . . . . . . . . . . . . . . . . 129
▫ Turning The Rear Camera On Or Off —
Without Navigation Radio . . . . . . . . . . . . . . 130
䡵 Overhead Console — If Equipped . . . . . . . . . . 130
䡵 Garage Door Opener — If Equipped . . . . . . . . 130▫ Programming HomeLink威 . . . . . . . . . . . . . . 132
▫ Gate Operator/Canadian Programming . . . . 134
▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 135
▫ Reprogramming A Single HomeLink威Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 136
▫ General Information . . . . . . . . . . . . . . . . . . 136
䡵 Power Sunroof — If Equipped . . . . . . . . . . . . 137
▫ Opening Sunroof — Express . . . . . . . . . . . . 138
▫ Closing Sunroof — Express . . . . . . . . . . . . . 138
▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . 138
▫ Pinch Protect Override . . . . . . . . . . . . . . . . 138▫ Venting Sunroof — Express . . . . . . . . . . . . . 138
▫ Sunshade Operation . . . . . . . . . . . . . . . . . . 139
▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 139
▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 139
▫ Ignition Off Operation . . . . . . . . . . . . . . . . . 139
▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . 139
䡵 Command-View™ Skylights — If Equipped . . . 139
䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 140
䡵 Power Inverter — If Equipped . . . . . . . . . . . . 143
䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 145䡵 Cargo Area Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81
▫ Front Cupholders . . . . . . . . . . . . . . . . . . . . 145
▫ Cupholders — Second Row Seat . . . . . . . . . 146
▫ Cupholders — Third Row Seat . . . . . . . . . . . 146
. . . . . . . . . . . . . . . . . . . 147
▫ Cargo Load Floor . . . . . . . . . . . . . . . . . . . . 147
䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 148
▫ Rear Window Wiper/Washer . . . . . . . . . . . . 148
▫ Rear Window Defroster . . . . . . . . . . . . . . . . 150
䡵 Roof Luggage Rack — If Equipped . . . . . . . . . 15082 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS
Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
Adjusting Rear View Mirror
Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will indicate when the dimming feature is activated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83
Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
WARNING!
Vehicles and other objects seen in the passenger-side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger-side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger-side mirror.
Exterior Mirrors Folding Feature All exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward and normal.
Automatic Dimming Mirror
CAUTION!
To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Automatic Dimming Mirrors — If Equipped The driver and passenger outside mirrors will automati- cally adjust for glare from vehicles behind you. This feature is controlled by the inside Automatic Dimming Mirror and can be turned on or off by pressing the button at the base of the inside mirror. The mirrors will auto- matically adjust for headlight glare when the inside mirror adjusts. Power Mirrors The power mirror switch is located on the driver’s door trim panel, next to the power door lock switch. A rotary knob selects the left mirror, right mirror or off position. After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a mirror position.
Power Mirror Switches
Heated Mirrors — If Equipped
These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in this section, for further information.
Illuminated Vanity Mirrors — If Equipped To access an illuminated vanity mirror, flip down one of the sun visors. Lift the cover to reveal the mirror. The light will turn on automatically.
Lighted Vanity Mirror
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85
Sun Visor Extension — If Equipped This feature has a pull out extension on the sun visor for increased coverage.
uconnect™ phone — IF EQUIPPED
Refer to “uconnect™ phone” in the uconnect™ User Manual located on the DVD for further details.
VOICE RECOGNITION (VR) SYSTEM — IF EQUIPPED Refer to “Voice Recognition (VR)” in the uconnect™ User Manual located on the DVD for further details.
SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
• DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and
using a seat belt properly.
Front Manual Seat Adjustment Move the seat forward or rearward using the adjustment bar. Lift up on the bar located on the front of the seat near the floor. Using body pressure, move forward and rear- ward on the seat to be sure the seat adjusters have latched.
WARNING!
Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Front Seat Adjustment — Recline To adjust the seatback, lift the lever located on the outboard side of the seat, lean back and release the lever at the desired position. To return the seatback, lift the lever, lean forward and release the lever.
WARNING!
Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
Manual Lumbar Support Adjustment The manual lumbar support adjustment lever is located on the right side of the driver’s seatback and on the left side of the passenger’s seatback (if equipped). Moving the lumbar control lever fore and aft increases or de- creases the lumbar support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87
Manual Lumbar Control
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Eight–Way Driver’s Power Seat The driver’s power seat switches are located on the outboard side of the driver’s seat. The bottom switch controls up/down, forward/rearward, and tilt adjust- ment. The top switch controls the seatback recline adjust- ment.
Power Seat Switches
WARNING!
Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
CAUTION!
Do not place any article under any seat as it may cause damage to the seat controls.
Four-Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger seat. The bottom switch controls forward/rearward adjustment. The top switch controls the seatback recline adjustment.
NOTE: The four-way seat does not have an up/down adjustment.
WARNING!
Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
CAUTION!
Do not place any article under any seat as it may cause damage to the seat controls.
Head Restraints Head restraints can reduce the risk of injury in the event of a rear impact. Adjustable head restraints should be adjusted so that the upper edge is as high as practical.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89
The head restraints have a locking button which must be pushed in to lower the head restraint to all positions. The restraints may be raised without pushing in the button.Adjustable Head Restraints
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in PARK.
Front Heated Seats — If Equipped The controls for each heater are located near the bottom center of the instrument panel (below the heater/air conditioning controls). After turning the ignition ON, you can choose from High, Low or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off.
Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.
When High-level heating is selected, the heaters provide a boosted heat level during the first four minutes of operation after heating is activated. The heat output then drops to the normal High-level. If High-level heating is selected, the system will automatically switch to the Low-level after approximately 30 minutes of continuous operation. At that time, the number of illuminated LEDs changes from two to one, indicating the change. Opera- tion on the Low-level setting also turns Off automatically after approximately 30 minutes. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes.
WARNING!
• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. To avoid heated seat surfaces coming in contact and poten- tial seat overheating, always ensure that the seat heater is in the off position before placing any of the seats into a folded flat position (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91
Rear Heated Seats — If Equipped On vehicles equipped with rear heated seats, the seats closest to the doors are heated. The controls for these seats are located on the rear of the center console.
Rear Heated Seat Switches
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After turning the ignition ON, you can choose from High, Low or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off.
Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.
When the High-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal High-level. If the High-level setting is selected, the system will automatically switch to Low-level after approximately 30 minutes of continuous operation. At that time, the number of illuminated LEDs changes from
two to one, indicating the change. The Low-level setting will turn Off automatically after approximately 30 min- utes. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes.
WARNING!
• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at Low temperatures, especially if used for long periods of time.
(Continued)
WARNING! (Continued)
• Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. To avoid heated seat surfaces coming in contact and poten- tial seat overheating, always ensure that the seat heater is in the Off position before placing any of the seats into a folded flat position (if equipped).
40/20/40 Second Row Folding Seat
Fold and Tumble Second Row Seat The left, center, or right side of the second row seat can be lowered to allow for extended cargo space, and still maintain some rear seating room. In addition, the left and right side of the second row seat can be lowered and tumbled forward to allow access to the third row seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93
1. Pull up on the seatback lever located on the outboard side of the seat. NOTE: Pulling upward on this handle allows the out- board seating positions to be reclined.Seatback Release Lever
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the seatback down, and tumble the seat forward.
WARNING!
Do not drive the vehicle with the outer second row seats in the tumbled position. The outer second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury.
Fold And Tumble Seat
If sitting in the third row seat, pull rearward on NOTE: the release strap located at the rear of the seat and tumble the seat forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95
Folding Middle Seatback (Second Row Seat) 1. Pull the release strap.
Release Strap
Release Strap
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Lower the center seatback.
Center Seat Armrest (Second Row Seat) — If Equipped The second row center seat may be equipped with a armrest. Pull strap to lower armrest.
Folding Center Seatback
Armrest (Second Row Seat)
50/50 Third Row Folding Seat — If Equipped
To Lower Rear Seat Either side of the third row seat can be lowered to allow for extended cargo space and still maintain some rear seating room. 1. Open the tailgate. 2. Pull the seatback release handle (toward rear of ve- hicle) and lower the seatback using the pull strap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97
Seatback Release Handle
3. Close the tailgate.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise Rear Seat 1. Open the tailgate. 2. Detach pull strap from back of seat and pull seatback upward until it locks into place. Reattach strap.
3. Close the tailgate.
Pull Strap
WARNING!
The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident. Children should be seated and using the proper restraint system.
DRIVER MEMORY SEAT — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals and radio station preset settings. Your Remote Keyless Entry (RKE) transmitters can also be pro- grammed to recall the same positions when the UN- LOCK button is pressed.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99
Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory
NOTE: Each time the S (SET) button and a numbered button 1 or 2 are pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key, and turn the ignition switch to the ON position. 2. Press the driver door MEMORY button number 1 if you are setting the memory for driver 1, or button number 2 if you are setting the memory for driver 2. The system will recall any stored settings. Wait for the system to complete the memory recall before continuing to Step 3. 3. Adjust the driver’s seat, recliner, and driver’s sideview mirror to the desired positions. 4. Adjust the brake and accelerator pedals to the desired positions.
Driver Memory Switches
Your vehicle is equipped with two RKE transmitters. One or both RKE transmitters can be linked to either memory position. The memory system can accommodate up to four RKE transmitters, each one linked to either of the two memory positions.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Turn on the radio and set the radio station presets (up to 12 AM and 12 FM stations can be set). 6. Turn the ignition switch to the LOCK position and remove the key. 7. Press and release the S (SET) button located on the driver’s door. 8. Within five seconds, press and release MEMORY button 1 or 2 on the driver’s door. The next step must be performed within five seconds if you desire to also use a RKE transmitter to recall memory positions. 9. Press and release the LOCK button on one of the RKE transmitters. 10. Insert the ignition key, and turn the ignition switch to the ON position. 11. Select ⬙Remote Linked to Memory⬙ in the Electronic Vehicle Information Center (EVIC) and enter ⬙Yes⬙. Refer
to “Electronic Vehicle Information Center (EVIC) — Customer-Programmable Features” in Section 4 for more information. 12. Repeat the above steps to set the next memory position, using the other numbered memory button, or to link another RKE transmitter to memory. Memory Position Recall
NOTE: The vehicle must be in PARK to recall memory positions. If a recall is attempted when the vehicle is not in PARK, a message will be displayed in the Electronic Vehicle Information Center (EVIC). To recall the memory settings for driver one, press MEMORY button number 1 on the driver’s door, or the UNLOCK button on the RKE transmitter linked to memory position 1.
To recall the memory setting for driver two, press MEMORY button number 2 on the driver’s door, or the UNLOCK button on the RKE transmitter linked to memory position 2. A recall can be cancelled by pressing any of the MEMORY buttons on the drivers door during a recall (S, 1, or 2). When a recall is cancelled, the driver’s seat, driver’s mirror and the pedals stop moving. A delay of one second will occur before another recall can be selected. To Disable a RKE Transmitter Linked to Memory
1. Turn the ignition switch to the LOCK position, and remove the key. 2. Press and release MEMORY button number 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continuing to Step 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101
3. Press and release the memory S (SET) button located on the driver’s door. 4. Within five seconds, press and release MEMORY button 1 on the driver’s door. 5. Within five seconds, press and release the UNLOCK button on the RKE transmitter. To disable another RKE transmitter linked to either memory position, repeat steps 1 through 5 for each RKE transmitter. NOTE: Once programmed, all RKE transmitters linked to memory can be easily enabled or disabled at one time. Refer to Remote Linked to Memory under ⬙Electronic (EVIC) — Customer- Vehicle Programmable Features⬙ for more information.Information Center
in Section 4
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry/Exit Seat This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. There are two possible Easy Entry/Exit adjustments available: • The seat cushion will move rearward approximately 2.5 in (60 mm), if the starting position of the seat is greater than or equal to 2.67 in (68 mm) forward of the rear seat stop when the key is removed from the ignition switch. The seat will then move forward approximately 2.5 in (60 mm) when the key is placed into the ignition and turned out of the LOCK position. • The seat will move to the position located 0.3 in (8 mm) forward of the rear stop if the starting position is between 0.9 to 2.67 in (23 to 68 mm) forward of the rear stop when the key is removed from the ignition switch. The seat will move forward to the memory/
driving position when the key is placed into the ignition, and turned out of the LOCK position toward the ACC/ON position.
The Easy Entry/Exit feature will be automatically dis- abled if the seat is already positioned closer than 0.9 in (23 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit/Entry. Each stored memory setting will have an associated Easy Entry/Exit position. NOTE: The Easy Entry/Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry/Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to ⬙Electronic Vehicle Information Center (EVIC) — Customer-Programmable Features⬙ in Section 4 for more information.
TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the release lever inside your vehicle located below the instrument panel and in front of the driver’s door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103
Hood Release Handle
2. Reach under the hood, move safety latch to the left and lift the hood.
Underhood Safety Latch
CAUTION!
To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving.
LIGHTS
Multifunction Lever The multifunction lever controls the operation of the headlights, turn signals, headlight beam selection, instru- ment panel interior courtesy/dome lights and optional fog lights. The mul- tifunction lever is located on the left side of the steering column.
light dimming, passing light,
Multifunction Lever
Headlights and Parking Lights Turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Turn to the third detent for Auto- matic Headlight operation (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105
Automatic Headlight System — If Equipped Turn the end of the multifunction lever to the third detent (AUTO) to activate the Automatic Headlight system.
Headlight Switch
Headlight Switch
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This system performs two functions. With the engine running and the multifunction lever in the AUTO posi- tion, the headlights will turn on and off based on the surrounding light levels. Headlights On Automatically With Wipers If your vehicle is equipped with Automatic Headlights it also has this customer-programmable feature. When your headlights are in the AUTO position, and the engine is running, they will automatically turn on when the wiper system is on. Refer to “Headlamps On with Wipers” under “Electronic Vehicle Information (EVIC) — Customer-Programmable Features” in Section 4. If your vehicle is equipped with a “Rain Sensitive Wiper System,” and it is activated, the headlights will automati- cally turn on after the wipers complete five wipe cycles within approximately one minute, and they will turn off
approximately four minutes after the wipers completely stop. Refer to “Windshield Wipers and Washers” in this section for more information. NOTE: When your headlights come on during the daytime, the instrument panel lights will automatically dim to the lower nighttime intensity. Refer to “Instru- ment Panel and Interior Lights” below for setting the instrument panel lights to full daytime intensity. SmartBeam™ — If Equipped The SmartBeam™ system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle spe- cific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.
If the windshield or SmartBeam™ mirror is NOTE: replaced, the SmartBeam™ mirror must be re-aimed to ensure proper performance. See your local authorized dealer. To Activate 1. Select “Auto High Beams” Refer to “Electronic Vehicle Information Center (EVIC) — Customer-Programmable Features” in Section 4 of this manual. 2. Turn the end of the multifunction lever to the AUTO headlight position. 3. Push the multifunction lever away from you (toward front of vehicle) to engage the high beam mode. NOTE: This system will not activate until the vehicle is at or above 20 mph (32 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107
To Deactivate 1. Pull back on the multifunction lever to manually deactivate the system (normal operation of high beams). 2. Pull back on the multifunction lever once again to reactivate the system. NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, etc.) on the windshield or camera lens will cause the system to function improperly. Automatic Headlight Leveling — HID Headlights Only This feature prevents the headlights from interfering with the vision of oncoming drivers. Headlight leveling automatically adjusts the height of the headlight beam in reaction to changes in vehicle pitch.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights — If Equipped The high beam headlights come on at a low intensity level whenever the engine is running, and the transmis- sion is not in the PARK position. The lights remain on until the ignition switch is turned OFF or the parking brake is engaged. The headlight switch must be used for normal night time driving. Fog Lights — If Equipped
The fog light switch is located in the multifunction lever. To activate the fog lights, turn on the park/ turn lights, low beam headlights or Automatic Headlights and pull out the end of the multifunction lever. A light in the instrument cluster shows when the fog lights are on.
Front Fog Light Control
NOTE: • Turning on the high beam headlights turns off the fog
lights.
• A front fog light is a lighting device providing illumi- nation forward of the vehicle under conditions of fog, rain, snow or dust. The front fog lights supplement the low beams of a standard headlight system. • Proper aim and adjustments of the front fog lights should be made to prevent excessive glare for other drivers.
Instrument Panel and Interior Lights When the multifunction lever is in the parking light, headlight or AUTO position (if equipped), rotating the center portion of the lever up and down will increase and decrease the brightness (dimmer control) of the instru- ment panel lights. Full daytime brightness on all elec- tronic displays (odometer, overhead console, radio, and Automatic Temperature Control (if equipped) is obtained by rotating the center portion of the control to the first detent above the dimmer range. Rotating the control to the second detent above the dimmer range turns the
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109
interior lights on. Rotating the control to the “Off” (extreme bottom) position disables all the interior lights, even when the doors and liftgate are open. While in the “Off” position the instrument panel lighting is at the lowest light level and may not be suitable for night driving.Dimmer Control
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver Feature — Exterior/Interior Lights If the multifunction lever is left in the interior light position, parking light position, or the headlight position when the ignition switch is moved to the OFF position, the battery saver feature will automatically turn off the exterior and interior lights after eight minutes. Normal operation will resume when the ignition is turned ON or when the headlight switch is turned to another position. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
Turn Signal Control
If either light remains on and does not flash, or NOTE: there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, the indicator bulb is defective.
it would suggest
that
Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer- ing wheel. This will turn on the high beam headlights until the lever is released. Headlight Off Delay There is also a feature that delays turning off the vehicle lights for 0, 30, 60 or 90 seconds after the ignition switch is turned OFF. To activate the headlight delay, the multi- function lever must be rotated to the “Off” position after
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
the ignition switch is turned OFF. Only the headlights will illuminate during this time. Refer to “EVIC — Customer-Programmable Features” in Section 4 to turn this feature “On/Off” or set the time interval. Interior Lights The interior lighting consists of courtesy lights mounted below the instrument panel, reading lights located above the front and rear doors, and a rear cargo light. Opening a door or turning the center of the multifunction lever to the extreme up position will activate all interior courtesy lights. Courtesy/Reading LightsEach light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. There are also reading lights located above the rear doors. Each light can be turned on
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE by pressing the front recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time.
WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “Rear Window Features” in this section.
Courtesy/Reading Lights
Windshield Wiper/Washer Switch
Windshield Wiper Operation Rotate the end of the lever upward to the LO position for low-speed wiper operation. Rotate the end of the lever upward to the HI position for high-speed wiper operation.
Front Wiper Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113
CAUTION!
Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur.
Windshield Washer Operation To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermit- tent interval previously selected. If the lever is pulled while in the off position, the wipers will operate for several wipe cycles, then turn off.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
Mist Use the Mist feature when weather conditions make occasional usage of the wipers necessary. Pull down and release the control lever for a single wiping cycle.
Mist Control
Intermittent Wiper System Use one of the five intermittent wiper speeds when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Turn the end of the lever to one of the five delay positions for the desired
delay interval. The delay can be regulated from a maxi- mum of approximately 18 seconds between cycles, to a cycle every 1/2 second.
Front Wiper Control
NOTE: The wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115
Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of five settings to activate this feature. The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position 1 is the least sensitive, and wiper delay position 5 is the most sensi- tive. Setting 3 should be used for normal rain conditions. Settings 1 and 2 can be used if the driver desires less wiper sensitivity. Settings 4 and 5 can be used if the driver desires more sensitivity. Place the wiper switch in the OFF position when not using the system. NOTE: • The Rain Sensing feature will not operate when the
wiper switch is in the low or high-speed position.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
may reduce Rain Sensing performance.
• The Rain Sensing feature may not function properly when ice, or dried salt water is present on the wind- shield. • Use of Rain-X威 or products containing wax or silicone • A customer programmable feature in the Electronic Vehicle Information Center (EVIC) allows the Rain Sensing feature to be turned off. Refer to “Rain Sensing Wiper” under “Electronic Vehicle Information Center (EVIC) — Customer-Programmable Features” in Sec- tion 4 of this manual.
The Rain Sensing system has protection features for the wiper blades and arms, and will not operate under the following conditions:
• Low Ambient Temperature — When the ignition is first turned ON, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 0 mph (0 km/h), or the outside tem- perature is greater than 32°F (0°C). • Transmission in NEUTRAL Position — When the ignition is ON, and the transmission is in the NEU- TRAL position, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the shift lever is moved out of the NEUTRAL position.
TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column.
Tilt/Telescoping Control Handle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117
To unlock the steering column, push the control handle downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as de- sired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle upward until fully engaged.WARNING!
Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driv- ing. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle.
ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The position of the brake and accelerator pedals can be adjusted without compromising safety or comfort in actuating the pedals.
Adjustable Pedal Switch
Press the bottom of the switch to move the pedals forward (away from the driver). Press the top of the switch to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE (R) or when the Electronic Speed Control is on. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Set” or “Adjustable Pedal Disabled — Shifter In Re- verse”). Refer to Electronic Vehicle Information Center (EVIC) in Section 4 for more information.
CAUTION!
Do not place any article under the adjustable pedal’s or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.
WARNING!
Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked.
ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119
The Electronic Speed Control lever is located on the right side of the steering wheel.Electronic Speed Control Lever
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously. If this occurs, the Electronic Speed Con- trol System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate. To turn the Elec- tronic Speed Control system OFF, push the ON/OFF button a second time. The Cruise Indicator Light will turn off. The Electronic Speed Control system should be turned OFF when not in use.
WARNING!
Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the Electronic Speed Control or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Con- trol system OFF when you are not using it.
To Set a Desired Speed When the vehicle has reached the desired speed, press down on the Electronic Speed Control lever and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever.
To Deactivate A soft tap on the brake pedal, pulling the Electronic Speed Control lever toward you, or normal brake pres- sure while slowing the vehicle will deactivate Electronic Speed Control without erasing the set speed memory. Pressing the ON/OFF button or turning off the ignition switch erases the set speed memory. To Resume Speed To resume a previously set speed, push the RESUME ACCEL lever up and release. Resume can be used at any speed above 20 mph (32 km/h). To Vary the Speed Setting When the Electronic Speed Control is ON, speed can be increased by pushing up and holding RESUME ACCEL. Release the Electronic Speed Control lever when the desired speed is reached, and the new speed will be set. Tapping RESUME ACCEL once will result in a 1 mph (2 km/h) speed increase. Each time the Electronic Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121
Control lever is tapped, speed increases so that tapping the Electronic Speed Control lever three times will in- crease speed by 3 mph (5 km/h). To decrease speed while Electronic Speed Control is ON, push down and hold SET DECEL. Release the Electronic Speed Control lever when the desired speed is reached, and the new speed will be set. Tapping the SET DECEL lever once will result in a 1 mph (2 km/h) speed decrease. Each time the lever is tapped, speed decreases. To Accelerate for Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills The automatic transmission may downshift on hills to maintain the vehicle set speed.122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The Electronic Speed Control System maintains speed up and down hills. A slight speed change on moderate hills is normal. • On steep hills a greater speed loss or gain may occur so it may be preferable to drive without Electronic Speed Control.
REAR PARK ASSIST — IF EQUIPPED The Rear Park Assist provides visible and audible indi- cations of the distance between the rear fascia and the detected obstacle when backing up. Refer to the Warning Section and Note Section for limitations of this system and recommendations. The Rear Park Assist will remember the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the ON position.
The Rear Park Assist can be active only when the shift lever is in REVERSE. If the Rear Park Assist is enabled at this shift lever position, the system will be active until the vehicle speed is increased to approximately 11 mph (18 km/h) or above. The system will be active again if the vehicle speed is decreased to speeds less than approxi- mately 10 mph (16 km/h). Rear Park Assist Sensors The four Rear Park Assist Sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12
to 59 in (30 to 150 cm) from the rear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle.Rear Park Assist Warning Display The Rear Park Assist Warning Display, located in the headliner near the flipper glass, provides both visible and audible warnings to indicate the distance between the rear fascia and the detected obstacle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123
When the ignition is turned to the ON position, the warning display will turn ON all of its LEDs for about one second. Each side of the warning display has six yellow and two red LEDs. The vehicle is close to the obstacle when the red LED is ON. The system dimly illuminates the two outer most yellow LEDs when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle:Rear Park Assist Display
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES
DISPLAY LED
OBSTACLE DISTANCE FROM:
LED COLOR
AUDIBLE SIGNAL
1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED 8th LED
REAR CORNERS
31.5 in (80 cm) 25.5 in (65 cm) 20 in (50 cm) 16 in (40 cm) 6 in (15 cm)
REAR CENTER 59 in (150 cm) 51 in (130 cm) 45 in (115 cm) 39 in (100 cm) 33.5 in (85 cm) 28 in (70 cm) 20 in (50 cm) 12 in (30 cm)
NOTE: The Rear Park Assist system will MUTE the radio, if on, when the system is sounding an audio tone. Enable/Disable The Rear Park Assist The Rear Park Assist can be enabled and disabled with a switch located on the upper switch bank of the instru- ment panel.
Yellow Yellow Yellow Yellow Yellow Yellow Red Red
Yes, Half Second
None None None None None
Yes, Intermittent Yes, Continuous
Press the switch once to turn the Rear Park Assist on, push the switch a second time to turn the Rear Park Assist off.
When the switch is pressed to disable the system, the instrument cluster will display the “PARK ASSIST DIS- ABLED” message. Refer to “Electronic Vehicle Informa- tion Center (EVIC)” in Section 4 of this manual. When the shift lever is changed to REVERSE and the system is disabled, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the message. The Rear Park Assist Switch LED will be ON when the Rear Park Assist is disabled or defective. The Rear Park Assist Switch LED will be OFF when the system is enabled. Service The Rear Park Assist When the Rear Park Assist is defective, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the “SERVICE PARK ASSIST SYSTEM” message. Refer to “Electronic Vehicle Informa- tion Center (EVIC)” in Section 4 of this manual. If
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125
“SERVICE PARK ASSIST SYSTEM” appears in the EVIC after making sure the rear fascia/bumper is clean and free of snow, ice, mud, or other debris, see your autho- rized dealer. Cleaning The Rear Park Assist Clean the Rear Park Assist Sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. System Usage Precautions NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the Rear Park Assist System operating prop- erly. • Jackhammers, large trucks, and other vibrations could affect the performance of the Rear Park Assist System.126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
• When you turn off the Rear Park Assist System, the instrument cluster will display “PARK ASSIST DIS- ABLED.” Furthermore, once you turn off the Rear Park Assist System, it remains off until you turn it on again, even if you cycle the ignition key. • When you move the shift lever to the REVERSE position and the Rear Park Assist System is turned off, the instrument cluster will display “PARK ASSIST DISABLED” message for as long as the vehicle is in REVERSE. • The Rear Park Assist System, when on, will MUTE the • If a Rear Park Assist System malfunction occurs, a single chime will sound once per ignition cycle. In addition, the Electronic Vehicle Information Center
radio when it is sounding a tone.
(EVIC) will display “SERVICE PARK ASSIST SYS- TEM”. If this occurs making sure the rear fascia/ bumper is free from snow, ice, mud, dirt and debris, see your authorized dealer. • Clean the Rear Park Assist Sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt, or debris. Failure to do so can result in the system not working properly. The system might not detect an obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/ bumper. • Objects must not be within 12 in (30 cm) from the rear fascia/bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “SERVICE PARK ASSIST SYSTEM” message to be displayed in the instrument cluster.
CAUTION!
• The Rear Park Assist System is only a parking aid and it is unable to recognize every obstacle, in- cluding small obstacles. Parking curbs might be temporarily detected or not detected at all. Ob- stacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using the Rear Park Assist System to be able to stop in time when the obstacle is detected. It is recommended that the driver looks over his/her shoulder when using the Rear Park Assist System.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127
WARNING!
• Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots be- fore backing up. You are responsible for safety and must continue to pay attention to your surround- ings. Failure to do so can result in serious injury or death.
(Continued)
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING! (Continued)
• Before using the Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the ve- hicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns on the single flashing arc and sounds the continuous tone. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.
REAR CAMERA — IF EQUIPPED Vehicles may be equipped with a rearview camera (lo- cated on the rear liftgate) that allows you to see an on-screen image (on the Navigation/Multimedia radio) of the rear of your vehicle, whenever the vehicle is put into REVERSE.
WARNING!
Drivers must be careful when backing up even when using the Rear Camera System. Always check care- fully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must con- tinue to pay attention while backing up. Failure to do so can result in serious injury or death.
CAUTION!
• To avoid vehicle damage, the Rear Camera system should only be used as a parking aid. The Rear Camera system is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using the Rear Camera system to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using the Rear Camera system.
If snow, ice, mud, or anything else builds up on NOTE: the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129
Turning the Rear Camera On or Off — With Navigation Radio 1. Press the ⬙menu⬙ hard key. 2. Select ⬙system setup⬙ soft key. 3. Press the “camera setup” soft key. 4. Enable or disable the rear camera feature by selecting ⬙enable rear camera in reverse⬙ soft key. 5. Press the “save” soft key. 6. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to ⬙check entire surroundings⬙ displayed across the top of the screen. After five seconds this note will disappear. 7. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the navigation or audio screen appears again.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning the Rear Camera On or Off — Without Navigation Radio 1. Press the ⬙menu⬙ hard key. 2. Select ⬙system setup⬙ soft key. 3. Enable or disable the rear camera feature by selecting ⬙enable rear camera in reverse⬙ soft key. 4. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to ⬙check entire surroundings⬙ displayed across the top of the screen. After five seconds this note will disappear. 5. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the audio screen appears again.
OVERHEAD CONSOLE — IF EQUIPPED The overhead console contains an optional universal garage door opener (HomeLink威), storage for sunglasses, and optional power sunroof switches.
GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit operates off your vehicle’s battery. The HomeLink威 buttons are located in the overhead console and contain one, two, or three dots/lines desig- nating the different HomeLink威 channels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131
WARNING!
• Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or as- sistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death.
HomeLink威 Buttons
NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink姞
Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds. The EVIC will display “CLEARING CHANNELS.” Release the buttons when the EVIC mes- sage states “CHANNELS CLEARED.” It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage while training. 1. Turn the ignition switch to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. For optimal training, point the battery end of the hand- held transmitter away from the HomeLink威. 3. Simultaneously, press and hold both the chosen HomeLink威 button and the hand-held transmitter button until the EVIC display changes from “CHANNEL # TRAINING” to “CHANNEL # TRAINED.” Then release both the HomeLink威 and hand-held trans- mitter buttons. If the EVIC display states “DID NOT TRAIN” repeat Step 3. If the signal is too weak, replace the battery in the original hand-held transmitter. It may take up to 30 seconds, or longer in rare cases. The garage door may open and close while you train.
NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. 4. Press and hold the just-trained HomeLink威 button. If the channel has been trained, the EVIC display will now state “CHANNEL # TRANSMIT.” If the EVIC display still states “CHANNEL # TRAIN- ING” repeat Step 3. NOTE: After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “learn” or “training” button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133
This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door).1 — Garage Door Opener 2 — Training Button
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Firmly press and release the “LEARN” or “TRAIN- ING” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels.
Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink” Step 3 with the following: 3. Continue to press and hold the HomeLink威 button while you press and release - every two seconds (“cycle”) your hand-held transmitter until HomeLink威 has successfully accepted the frequency signal. The EVIC display will change from “CHANNEL # TRAIN- ING” to “CHANNEL # TRAINED.”
If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink威” earlier in this section. Using HomeLink姞 To operate, simply press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.) The hand-held transmitter of the device may also be used at any time. Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135
2. Press and hold the desired HomeLink威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. Without releasing the button, proceed with Program- ming HomeLink威 Step 2 and follow all remaining steps. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the EVIC message states “CHANNELS CLEARED.” Note that all channels will be erased. Indi- vidual channels cannot be erased. The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active.136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the learn button on the garage door opener to • Did you unplug the device for training and remember
complete the training for rolling code.
to plug it back in?
If you are having any problems or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.
2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. The term “IC:” before the certification/registration num- ber only signifies that Industry Canada technical specifi- cations were met.
POWER SUNROOF — IF EQUIPPED The power sunroof switch is located on the overhead console.
Power Sunroof Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137
WARNING!
• Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. • Do not allow small children to operate the sun- roof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof — Express Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the
sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof — Express Press and release the ⬙V⬙ button, and the sunroof will open to the vent position. This is called “Express Vent”, and will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.
Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139
Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned OFF. Opening either front door will cancel this feature. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed.
COMMAND-VIEW™ SKYLIGHTS — IF EQUIPPED The two fixed skylights are above the second row seats. The glass is tinted to shield the second row occupants from the sun and glare. Each skylight includes a roller shade that is concealed in the assembly to block out more light when desired.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Hold onto shade handle until shade is com- pletely open or closed.
Roller Shade
ELECTRICAL POWER OUTLETS Your vehicle is equipped with 12 Volt power outlets that can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is powered. Power outlets labeled with a “key” are powered when the ignition switch is in the ON or ACC position, while the outlets labeled with a “battery” are connected directly to the battery and powered at all times. NOTE: • Do not exceed the maximum power of 160 Watts (13
• All accessories connected to the “battery” powered outlets should be removed or turned off when the vehicle is not in use to protect the battery against discharge.Amps) at 12 Volts for either of these outlets.
• To ensure proper operation a MOPAR威 knob and
element must be used.
The front power outlets are located to the left and right of the convenience tray (lower center of instrument panel). Pull lightly on the tab of the plastic cover to access these power outlets.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141
The power outlet located on the left side of the tray can be used to power a conventional cigar lighter. The rear power outlet (if equipped) is located in the left rear cargo area.Front Power Outlets
Rear Power Outlet
CAUTION! (Continued)
• Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
WARNING!
To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an
the vehicle.
electric shock and failure.
CAUTION!
• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.
(Continued)
POWER INVERTER — IF EQUIPPED There is a 115 Volt, 150 Watt inverter outlet located on the back of the center console to convert DC current to AC current. This outlet can power cellular phones, electron- ics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Play- station3 and XBox360 will exceed this power limit, as will most power tools.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143
Power Inverter
The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. Press the power inverter switch (located on the upper switch bank) to turn the power on to the outlet. Press the switch again to turn the power off.
Power Inverter Switch
NOTE: When the power inverter switch is pressed, there will be a delay of approximately one second before the inverter status indicator turns ON. The status indica- tor of the AC power inverter indicates whether the inverter is producing AC power.
WARNING!
To avoid serious injury or death: • Do not use a three-prong adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric
shock and failure.
CUPHOLDERS
Front Cupholders There are two cupholders for the front seat passengers, located in the center console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145
Front Cupholders
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cupholders — Second Row Seat The second row seat has two cupholders in the center armrest. Lower the center armrest. Refer to “Seats” in this section. Press the front of the cupholder, and the cup- holder will come out of the armrest.
Cupholders — Third Row Seat The third row seat passengers have cupholders on the left and right rear trim panels.
Cupholders — Second Row Seat
Cupholders — Third Row Seat
CARGO AREA FEATURES
Cargo Load Floor
The panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a variety of items. The cargo load floor is held by spring loaded latches. In order to use the cargo load floor, use the following procedure:
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147
Rear Storage Cover
NOTE: used as cargo tie-downs.
The cargo load floor latches should not be
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 3. Lift tray over loop(s), and reposition tray.
4. Pull up on loop(s) and twist 90 degrees, so they are perpendicular (straight up) to the slotted hole in tray. 5. Push loop(s) back down, so they are parallel to the top of the tray.
REAR WINDOW FEATURES
Rear Window Wiper/Washer
The rear wiper/washer is controlled by a rotary switch located on the control lever. The control lever is located on the right side of the steering column.
Cargo Load Floor
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149
Rotate the switch upward to the “washer” position to activate that rear washer. The washer pump will continue to operate as long as the lever or ring is engaged. Upon release, the wipers will cycle two times before returning to the set position. If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the “park” position if power accessory delay is active. Power acces- sory delay can be cancelled by opening the door; if this happens, the rear wiper will stop at its current position and will not go to “park”. If the liftgate flipper glass is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, the rear wiper switch, or the ignition switch, needs to be turned OFF and ON to restart the rear wiper.Rear Wiper/Washer Control
Rotate the switch upward to the “On” position to activate the rear wiper.
NOTE: The rear wiper operates in an intermittent mode only.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Window Defroster
The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating.
CAUTION!
Failure to follow these cautions can cause damage to the heating elements:
(Continued)
CAUTION! (Continued)
• Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window.
ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars.
If not equipped with crossbars, your authorized NOTE: dealer can order and install MOPAR威 crossbars built specifically for this roof rack system. Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. The optional crossbars must be installed using the correct orientation (the longer crossbar toward the front) with the raised edge (wind trip) toward the front of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151
1 — Front of Vehicle 2 — Raised Edge (Wind Trip)
3 — Thumb Screws
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The optional crossbars must also be secured in one of the five detent positions marked with an arrow on the siderails to prevent movement. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately eight turns, then move the crossbar to the desired position, keeping the crossbars parallel to the rack frame. Once the crossbar is in one of the five detent positions, retighten the thumb screws to lock the crossbar into position. NOTE: • To help control wind noise when the crossbars are not in use, place the front crossbar in the first detent from the front of the vehicle and the rear crossbar in the second detent from the rear of the vehicle.
• If the rear crossbar (or any metallic object) is placed over the satellite radio antenna (if equipped), you may experience interruption of satellite radio reception. For improved satellite radio reception, place the rear cross- bar in the second detent from the rear of the vehicle when not in use.
• The grab handles on the back of
the vehicle (if
equipped) are not to be used as a towing feature.
CAUTION!
• To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other protection between the load and the roof surface.
(Continued)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153
WARNING!
Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack cautions when carrying cargo on your roof rack.
CAUTION! (Continued)
• To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropri- ately. • Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • Travel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to the cargo or your vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS
䡵 Instrument Panel Features . . . . . . . . . . . . . . . 158
䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 159
䡵 Instrument Cluster Description . . . . . . . . . . . . 160
䡵 Electronic Vehicle Information Center (EVIC) . . 170▫ Electronic Vehicle Information Center (EVIC)
Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
▫ Engine Oil Change Indicator System . . . . . . . 175
▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . 176
▫ Compass Display . . . . . . . . . . . . . . . . . . . . 179▫ Personal Settings (Customer-Programmable
Features)
. . . . . . . . . . . . . . . . . . . . . . . . . . 181
▫ System Status . . . . . . . . . . . . . . . . . . . . . . . 185䡵 Sales Code (RER/REN) — AM/FM/CD/DVD
Radio – If Equipped . . . . . . . . . . . . . . . . . . . . 186
▫ Operating Instructions — Voice RecognitionSystem (VR) — If Equipped . . . . . . . . . . . . . 186
▫ Operating Instructions — uconnect™ phone
— If Equipped . . . . . . . . . . . . . . . . . . . . . . 186
. . . . . . . . . . . . . . . 186▫ Clock Setting Procedure
156 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code RES — AM/FM Stereo Radio With
CD Player (MP3 AUX Jack) . . . . . . . . . . . . . . . 189
▫ Operating Instructions — Radio Mode . . . . . 189
▫ Operation Instructions — CD Mode For CDAnd MP3 Audio Play . . . . . . . . . . . . . . . . . 192
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 194
▫ Operation Instructions - Auxiliary Mode . . . . 197䡵 Sales Code RES/RSC — AM/FM Stereo Radio
With CD Player (MP3 AUX Jack) And Sirius Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
▫ Operating Instructions — Radio Mode . . . . . 198
▫ Operation Instructions — CD Mode For CDAnd MP3 Audio Play . . . . . . . . . . . . . . . . . 203
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 205
▫ List Button (CD Mode For MP3 Play) . . . . . . 208▫ Info Button (CD Mode For MP3 Play) . . . . . . 208
䡵 Universal Consumer Interface (UCI)
— If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 209
▫ Connecting The iPod威 . . . . . . . . . . . . . . . . . 210
▫ Using This Feature . . . . . . . . . . . . . . . . . . . 211
▫ Controlling The iPod威 Using RadioButtons . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 211
▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 213䡵 uconnect™ studios (Satellite Radio) — If
Equipped (REN/RER/RES Radios Only). . . . . . 215
▫ System Activation . . . . . . . . . . . . . . . . . . . . 215
▫ Electronic Serial Number/SiriusIdentification Number (ESN/SID) . . . . . . . . . 215
▫ Selecting uconnect™ studios (Satellite)
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 216
▫ Reception Quality . . . . . . . . . . . . . . . . . . . . 216
▫ Operating Instructions - uconnect™ studios(Satellite) Mode . . . . . . . . . . . . . . . . . . . . . 217
▫ Operating Instructions - uconnect™ phone
(If Equipped)
. . . . . . . . . . . . . . . . . . . . . . . 219
䡵 uconnect™ studios (Sirius Backseat TV™)
