Download PDF Manual

OWNER'S MANUAL


A030A01JM-AAT


Operation Maintenance Specifications


All information in this Owner's Manual is current at the time of publication. However, Hyundai reserves the right to make changes at any time so that our policy of continual product improvement may be carried out.


This manual applies to all Hyundai equipment. As a result, you may find material in this manual that does not apply to your specific vehicle.


models and includes descriptions and explanations of optional as well as standard


F1


OJM009001


EN hma cover.qxd 11/27/2006 5:07 PM Page 2


WARRANTIES FOR YOUR HYUNDAI VEHICLE


Please consult your Owner's Handbook & Warranty Information booklet for your vehicle's spe- cific warranty coverage.


RESPONSIBILITY FOR MAINTENANCE


The maintenance requirements for your new Hyundai are found in Section 7. As the owner, it is your responsibility to see that all maintenance operations specified by the manufacturer are carried out at the appropriate intervals. When the vehicle is used in severe driving conditions, more frequent main- tenance is required for some operations. Maintenance requirements for severe operating conditions are also included in Section 7.


A070A01A-AAT


CAUTION: MODIFICATIONS TO YOUR HYUNDAI


Your Hyundai should not be modified in any way. Such modifications may adversely affect the performance, safety or durability of your Hyundai and may, in addition, violate conditions of the limited warranties covering the vehicle. Certain modifications may also be in violation of regulations established by the U.S. Department of Transportation and other federal or state agencies.


A080A01S-AAT


TWO-WAY RADIO OR CELLULAR TELEPHONE INSTALLATION


Your vehicle is equipped with electronic fuel injection and other electronic components. It is possible for an improperly installed/adjusted two-way radio or cellular telephone to adversely affect electronic systems. For this reason, we recommend that you carefully follow the radio manufacturer's instruc- tions or consult your Hyundai dealer for precautionary measures or special instructions if you choose to install one of these devices.


F2


A090A01A-AAT


SAFETY AND VEHICLE DAMAGE WARNING


This manual includes information titled as WARNING, CAUTION and NOTE. These titles indicate the following:


This indicates that a condition may result in harm, serious injury or death to you or other persons if the warning is not heeded. Follow the advice provided with the warning.


WARNING:


CAUTION:


This indicates that a condition may result in damage to your vehicle or its equipment if the caution is not heeded. Follow the advice provided with the caution.


NOTE: This indicates that interesting or helpful information is being provided.


F3


A110A01A-AAT


VEHICLE DATA COLLECTION AND EVENT DATA RECORDERS


Your Hyundai vehicle is equipped with many high technology, electronically controlled systems that help to ensure your vehicle operates properly and provides the performance that you expect. These systems utilize computers to monitor the operation of various systems and components and help to control their operation. These computerized system operations are wide-ranging and involve components to reduce emissions, to continuously evaluate the readiness of the airbag and seat belt pretensioner systems, to determine when the airbag and seat belt pre-tensioner systems should be deployed and then to activate the deployment, and if equipped, to operate anti-lock braking, traction control and electrical stability control to assist the driver to control the vehicle in difficult driving situations. These systems electronically store information that is useful to service technicians when they need to diagnose and repair these systems. Additional information is stored only when a crash occurs that results in the deployment of the airbags or seat belt pre-tensioners. This type of data storage is done by devices called event data recorders(EDR).


After a crash event, the airbag and seat belt pre-tensioner computer system, known as the Supplemental Restraint System Control Module (SRSCM) or Airbag Control Unit (ACU), may record some information about the condition of the vehicle and how it was being operated. This information consists of data related to seat belt usage and if there was diagnostic information in the airbag or seat belt systems at the time that a crash occurred, and if the ACU sensed that a crash of sufficient severity occurred to require seat belt pre-tensioner or airbag deployment.


To retrieve this information, special equipment is needed and access to the vehicle or the device that stores the data is required. Hyundai will not access information about a crash event or share it with others except:


o in response to an official request of police or similar government office, or o with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee,


or


o as part of Hyundai’s defense of litigation, or o as required by law.


F4


A040A01A-AAT


FOREWORD


Thank you for choosing Hyundai. We are pleased to welcome you to the growing number of discriminating people who drive Hyundais. The advanced engineering and high-quality construction of each Hyundai we build is something of which we're very proud.


Your Owner's Manual will introduce you to the features and operation of your new Hyundai. It is suggested that you read it carefully because the information it contains can contribute greatly to the satisfaction you receive from your new car.


The manufacturer also recommends that all service and maintenance on your car be performed by an authorized Hyundai dealer. Hyundai dealers are prepared to provide high-quality service, maintenance and any other assistance that may be required.


A050A04A-AAT


HYUNDAI MOTOR AMERICA


Note: Because future owners will also need the information included in this manual, if you sell this Hyundai,


please leave the manual in the vehicle for their use. Thank you.


CAUTION:


Severe engine and transaxle damage may result from the use of poor quality fuels and lubricants that do not meet Hyundai specifications. You must always use high quality fuels and lubricants that meet the specifications listed on Page 9-4 in the Vehicle Specifications section of the Owner's Manual and which also appear in the Service Station Information on the back cover of the Owner's Manual.


Copyright 2008 Hyundai Motor America. All rights reserved. No part of this publication may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the prior written permission of Hyundai Motor America.


F5


A100A03A-AAT


Guide to Hyundai Genuine Parts 1. What are Hyundai Genuine Parts?


Hyundai Genuine Parts are the same parts used by Hyundai Motor Company to manufacture vehicles. They are de- signed and tested for the optimum safety, performance, and reliability to our cus- tomers.


2. Why should you use genuine parts? Hyundai Genuine Parts are engineered and built to meet rigid manufacturing requirements. Using imitation, counter- feit or used salvage parts is not covered under the Hyundai New Vehicle Lim- ited Warranty or any other Hyundai


warranty. In addition, any damage to or failure of Genuine Hyundai Parts caused by the installation or failure of an imita- tion, counterfeit or used salvage part is not covered by any Hyundai Warranty.


3. How can you tell if you are purchasing


Hyundai Genuine Parts? Look for the Hyundai Genuine Parts Logo on the package (see below).


Hyundai Genuine Parts exported to the United States are packaged with labels written only in English.


Hyundai Genuine Parts are only sold through Hyundai Dealerships.


authorized


To find the closest authorized dealer call 1-800-826-CARS


A100A03L


A100A01L


A100A02L


A100A04L


F6


SECTION


TABLE OF CONTENTS


FEATURES OF YOUR HYUNDAI


DRIVING YOUR HYUNDAI


WHAT TO DO IN AN EMERGENCY


CORROSION PREVENTION & APPEARANCE CARE


VEHICLE MAINTENANCE REQUIREMENTS


DO-IT-YOURSELF MAINTENANCE


EMISSION CONTROL SYSTEMS


CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS


VEHICLE SPECIFICATIONS


INDEX


10


F7


INSTRUMENTS AND CONTROLS


B250A01JM-AAT


F8


B250A01JM-U


1. Panel Brightness Control Knob (Rheostat Switch) 2. 4WD Lock Switch (If installed) 3. Traction Control System (TCS) Switch (If installed) /


Electronic Stability Control (ESC) Switch (If installed) Instrument Cluster


4. 5. Multi-Function Light Switch (If installed) 6. Front Window Defroster (If installed) / Aux Outlet (If


installed)


7. Hazard Warning Light Switch 8. Digital Clock 9. Windshield Wiper/Washer Switch


10. Rear Defroster and Outside Rearview Mirror Heater Switch


(If installed)


11. Front Fog Light Switch (If installed) 12. Passenger's Airbag 13. Hood Release Lever 14. Horn and Driver's Airbag 15. Small Article Tray / Ashtray (If installed) 16. Cruise Control Switch (If installed) 17. Heating/Air Conditioning Control Panel (If installed) 18. Shift Lever (If installed) 19. Glove Box


CAUTION:


When installing a container of liquid air freshener inside the vehicle, do not place it near the instrument cluster nor on the instrument panel surface. If there is any leakage from the air freshener onto these areas (Instrument cluster, instrument panel or air ventilator), it may damage these parts. If the liquid from the air freshener does leak onto these areas, wash them with water immediately.


F9


YOUR VEHICLE AT A GLANCE


B255A03JM-AAT


INDICATOR SYMBOLS ON THE INSTRUMENT PANEL


SRS (Airbag) Service Reminder Indicator (SRI)


ABS Service Reminder Indicator (If installed)


Turn Signal Indicator Lights


Seat Belt Reminder Light and Chime


Traction Control Indicator Light (If installed) Electronic Stability Control (ESC) Indicator Lights (If Installed)


High Beam Indicator Light


Cruise Indicator (If installed)


Low Oil Pressure Warning Light


SET Indicator Light (If installed)


Parking Brake/Brake Fluid Level Warning Light


4WD System Warning Light (If installed)


Charging System Warning Light


4WD Lock Indicator Light (If installed)


Tail Gate Open Warning Light


Low tire pressure telltale (If installed)


Door Ajar Warning Light and Chime (If installed)


TPMS (Tire pressure monitoring system) malfunc- tion indicator (If installed)


Low Fuel Level Warning Light


Engine coolant temperature warning light


Malfunction Indicator Light


* More detailed explanations of these items will be found begin- ning on page 1-50.


F10


FEATURES OF YOUR HYUNDAI


Fuel Recommendations ................................................ 1-2
Breaking in Your New Hyundai ..................................... 1-3
Keys .............................................................................. 1-3
Door .............................................................................. 1-4
Power Windows .......................................................... 1-12
Seats ........................................................................... 1-13
Seat Belts.................................................................... 1-19
Child Restraint System ............................................... 1-26
Supplemental Restraint (AIRBAG) system ................. 1-34
Instrument Cluster and Indicator Lights ...................... 1-48
Warning and Indicator Lights ...................................... 1-50
Multi-Function Light Switch ......................................... 1-60
Windshield Wiper/Washer Switch ............................... 1-62
Sunroof ....................................................................... 1-72
Mirror ........................................................................... 1-76
How to use Luggage Room ........................................ 1-80
Hood Release ............................................................. 1-85
Cruise Control ............................................................. 1-88
Heating and Cooling Control ....................................... 1-93
Stereo Sound System ............................................... 1-109
Antenna ..................................................................... 1-111
Audio System ............................................................ 1-113


1FEATURES OF YOUR HYUNDAI


FUEL RECOMMENDATIONS


B010A05A-AAT


Use Unleaded Gasoline


UNLEADED FUEL ONLY


B010A01JM Unleaded gasoline with a Pump Octane Rating of 87 (Research Octane Number 91) or higher must be used in your Hyundai.


WARNING:


o Do not "top off" after the nozzle auto-


matically shuts off when refueling.


o Tighten the cap until it clicks, other-


wise the "


" light will illuminate.


o Always check that the fuel cap is installed securely to prevent fuel spill- age in the event of an accident.


B010B01A-AAT


What About Gasohol? Gasohol (a mixture of 90% unleaded gaso- line and 10% ethanol or grain alcohol) may be used in your Hyundai. However, if your engine develops driveability prob- lems, the use of 100% unleaded gasoline is recommended. Fuels with unspecified quantities of alcohol, or alcohols other than ethanol, should not be used.


B010C01A-AAT


Use of MTBE Hyundai recommends that fuels contain- ing MTBE (Methyl Tertiary Butyl Ether) over 15.0% vol. (Oxygen Content 2.7% weight) should not be used in your Hyundai. Fuel containing MTBE over 15.0% vol. (Oxygen Content 2.7% weight) may re- duce vehicle performance and produce vapor lock or hard starting.


B010D01A-AAT


Do Not Use Methanol Fuels containing methanol (wood alco- hol) should not be used in your Hyundai. This type of fuel can reduce vehicle perfor- mance and damage components of the fuel system.


CAUTION:


Your Hyundai's New Vehicle Limited War- ranty may not cover damage to the fuel system and any performance problems that are caused by the use of fuels con- taining methanol or fuels containing MTBE (Methyl Tertiary Butyl Ether) over 15.0% vol. (Oxygen Content 2.7% weight.)


B010E01A-AAT


Gasolines for Cleaner Air To help contribute to cleaner air, Hyundai recommends that you use gasolines treated with detergent additives, which help prevent deposit formation in the en- gine. These gasolines will help the engine run cleaner and enhance performance of the Emission Control System.


B010F01A-AAT


Operation in Foreign Countries If you are going to drive your Hyundai in another country, be sure to:


o Observe all regulations regarding reg-


istration and insurance.


o Determine that acceptable fuel is avail-


able.


FEATURES OF YOUR HYUNDAI


KEYS


B030A01A-AAT


BREAKING IN YOUR NEW HYUNDAI


B020A01S-AAT


During the First 1,200 Miles (2,000
Km) No formal "break-in" procedure is required with your new Hyundai. However, you can contribute to the economical operation and durability of your Hyundai by observ- ing the following recommendations dur- ing the first 1,200 miles (2,000 km).


B030A01HR For greater convenience, the same key operates all the locks in your Hyundai. However, because the doors can be locked without a key, carrying a spare key is recommended in case you accidentally lock one key inside the car.


o Don't drive faster than 55 MPH (88 km/


h).


o While driving, keep your engine speed (rpm, or revolutions per minute) be- tween 2,000 rpm and 4,000 rpm.


o Use moderate acceleration. Don't start quickly or depress the accelerator pedal fully.


o For the first 200 miles (300 km), try to


avoid hard stops.


o Don't lug the engine (in other words, don't drive so slowly in too high a gear that the engine "bucks"-shift to a lower gear).


o Whether going fast or slow, vary your


speed from time to time.


o Don't let the engine idle longer than 3


minutes at one time.


o Don't tow a trailer during the first 1,200


miles (2,000 km) of operation.


1FEATURES OF YOUR HYUNDAI


B030B01A-AAT


Record Your Key Number


B030C01JM-AAT


ILLUMINATED IGNITION SWITCH (If installed)


B030B01HR A code number is stamped on the number plate that came with the keys to your Hyundai. This key number plate should not be left with the keys but kept in a safe place, not in the vehicle. The key number should also be recorded in a place where it can be found in an emergency. If you need additional keys, or if you should lose your keys, your authorized Hyundai dealer can make new keys if you can supply the key number.


B030C01E-1
Whenever either front door is opened, the ignition switch will be illuminated for your convenience, provided the ignition switch is not in the "ON" position. The light will go off approximately 10 sec- onds after closing the door or when the ignition switch is turned on.


DOOR LOCKS


B040A01A-AAT


WARNING:


o Unlocked doors can be dangerous. Before you drive away (especially if there are children in the car), be sure that all the doors are securely closed and locked so that the doors cannot be opened from the inside. This helps ensure that the doors will not be opened accidentally. Also, when com- bined with the proper use of seat belts, locking the doors helps keep occu- pants from being ejected from the car in case of an accident.


o Before opening the door, always look


for and avoid oncoming traffic.


FEATURES OF YOUR HYUNDAI


NOTE: o When pushing the lock switch of the driver's door to the "LOCK" position, only the driver's door can be locked. o If your vehicle is equipped with the central door locking system, the door will not lock if the key is left in the ignition switch when the front doors are closed.


o When locking the door this way, be careful not to lock the door with the ignition key left in the vehicle.


o To reduce the chances of theft, al- ways remove the ignition key, close all windows, and lock all doors and the tail gate when leaving your vehicle unattended.


B040B02JM-AAT


Locking, unlocking front doors with a key


B040C02O-AAT


Locking From the Outside (Driver's side - without key)


UNLOCK


LOCK


HJM2007
o The door can be locked or unlocked


with a key.


o Lock the door by turning the key toward the front of the vehicle and unlock it by turning the key toward the rear.


B040C01JM The doors can be locked without a key. To lock the doors, first push the inside lock switch to the "LOCK" position so that the red mark on the switch is not visible, then close the door.


❈ If your vehicle is installed with the re- mote keyless entry system, there is no key lock on the front passenger's door. (If installed)


NOTE: The driver's door can be unlocked by turning the key once toward the rear. If you wish to unlock all doors, turn the key again toward the rear within 4 seconds. The passenger's side will lock or unlock all doors with just one rotation.


1FEATURES OF YOUR HYUNDAI


B040D01O-AAT


Locking From the Inside (Driver's side)


B045C01JM-AAT


Locking From the Outside (Passenger's side - Without key)


UNLOCK


LOCK


o When locking the door this way, be careful not to lock the door with the ignition key left in the vehicle.


o To reduce the chances of theft, al- ways remove the ignition key, close all windows, and lock all doors and the tail gate when leaving your vehicle unattended.


HJM2008


To lock the door from the inside, simply close the door and push the lock switch to the "LOCK" position.


NOTE: o When pushing the lock switch of the driver's door to the "LOCK" position, only the driver's door can be locked. o When the door is locked, the red mark


on the switch is not visible.


o The driver's door can be opened by pulling the inside door handle even if the lock switch is depressed.


B045C01JM The door can be locked without a key. To lock the door, first push the inside lock switch to the "LOCK" position so that the red mark on the switch is not visible, then close the door.


NOTE: o When pushing the lock switch of the passenger's door to the "LOCK" po- sition, only the passengers door will be locked.


o If your vehicle is equipped with the central door locking system, the door will not lock if the key is left in the ignition switch when the front doors are closed.


FEATURES OF YOUR HYUNDAI


B045D01JM-AAT


Locking From the Inside (Passenger's side)


B040E04A-AAT


Child-Protector Rear Door Lock


B040G03HP-AAT


Central Door Locks Driver's door


LOCK


UNLOCK


Passenger's door


HJM2010


HJM2008-U


To lock the door from the inside, simply close the door and push the lock switch to the "LOCK" position. When this is done, neither the outside nor the passenger's inside door handles can be used.


NOTE: o When pushing the lock switch of the passenger's door to the "LOCK" po- sition, only the passenger's door locks.


o When the door is locked, the red mark


on the switch is not visible.


HJM2011
Your Hyundai is equipped with left and right side "child-protector" rear door locks. When the lock mechanism is engaged, the rear door cannot be opened from the in- side. Its use is recommended whenever there are small children in the rear seat. To engage the child-protector feature so that the door cannot be opened from the inside, move the child-protector lever to " position and close the door. Move the " " position when normal the lever to the " door operation is desired. To open the door from the outside, pull the outside door handle.


HJM2120
The central door locking switch is located on the front door arm rest. It is operated by depressing the door lock switch.


NOTE: o When pushing the front portion of the switch, all vehicle doors will lock. If any door is open when the switch is depressed, the door will remain locked when closed.


o When pushing the rear portion of the switch, all vehicle doors will unlock. o The central door locking is operated by turning the key in the front door lock toward the front or rear of the vehicle.


1FEATURES OF YOUR HYUNDAI


o If the door is locked/unlocked multiple times in rapid succession with either the vehicle key or door lock switch, the system may stop operating tem- porarily in order to protect the circuit and prevent damage to system com- ponents.


B070F03O-AAT


KEYLESS ENTRY SYSTEM (If installed) NOTE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undesired operation.


CAUTION:


Changes or modifications not expressly approved by the party responsible for compliance could void the user's au- thority to operate the equipment.


Locking doors 1. Close all doors. 2. Push the "LOCK" button on the transmit-


ter.


3. At the same time all doors lock, the turn signal lights will blink once to indicate that the system is armed.


Unlocking doors 1. Push the "UNLOCK" button on the trans-


mitter.


2. At the same time the driver's door un- locks, the turn signal lights will blink twice to indicate that the system is dis- armed.


NOTE: If you wish to unlock all doors, press the "UNLOCK" button on the transmitter again within 4 seconds.


NOTE: The transmitter will not work if any of following occur: - The ignition key is in ignition switch. - You exceed the operating distance


limit (393.7 inches [10 m]).


- The battery in the transmitter is weak. - Other vehicles or objects may be


blocking the signal.


- The weather is extremely cold. - The transmitter is close to a radio transmitter such as a radio station or an airport which can interfere with normal operation of the transmitter. When the transmitter does not work cor- rectly, open and close the door with the ignition key. If you have a problem with the transmitter, contact an authorized Hyundai Dealer.


NOTE: Keep the transmitter away from water or any liquid. If the keyless entry system is inoperative due to exposure to water or liquids, it will not be covered by your manufacturer vehicle warranty.


FEATURES OF YOUR HYUNDAI


THEFT-ALARM SYSTEM


B070A01A-AAT


(If installed) This system is designed to provide protec- tion from unauthorized entry into the car. This system is operated in three stages : the first is the "Armed" stage, the second is the "Alarm" stage and the third is the "Dis- armed" stage. If triggered, the system pro- vides an audible alarm with blinking of the turn signal lights.


B075B01O-AAT


Armed Stage


LOCK


UNLOCK


B070B02JM Park the car and stop the engine. Arm the system as described below.


1) Remove the ignition key from the igni-


tion switch.


2) Make sure that the hood and tail gate


are closed and latched.


3) Lock the doors using the transmitter of


the keyless entry system.


After completion of the steps above, the turn signal lights will blink once to indicate that the system is armed.


1FEATURES OF YOUR HYUNDAI 10


NOTE: o If any door, the tail gate or engine hood remains open, the system will not be armed. If this happens, rearm the system as described above.


o If the "LOCK" button is pressed once more within 4 seconds after pushing the "LOCK" button on the transmitter, the siren will sound once to indicate that the system is armed.


CAUTION:


Do not arm the system until all passen- gers have left the car. If the system is armed while a passenger(s) remains in the car, the alarm may be activated when the remaining passenger(s) leaves the car.


B075C01JM-AAT


Alarm Stage The alarm will be activated if any of the following occurs while the car is parked and the system is armed.


1) A front or rear door is opened without using the transmitter or the ignition key. 2) The tail gate is opened without using


the transmitter or the ignition key.


3) The hood is opened.


The siren will sound and the turn signal lights will blink continuously for about 30
seconds (This will repeat 3 times). To turn off the system, unlock the door or tail gate using the transmitter or the ignition key.


B075D01JM-AAT


Disarmed Stage The system will be disarmed by using the transmitter or the ignition key. The driver's door is unlocked by depress- ing once the "UNLOCK" button on the transmitter. If you wish to unlock all doors, press the "UNLOCK" button on the trans- mitter again within 4 seconds. Whenever the step above is completed, the turn signal lights will blink twice to indicate that the system is disarmed.


NOTE : The system will rearm if a door, tailgate, or hood is not opened within 30 seconds.


FEATURES OF YOUR HYUNDAI


11


Battery


Case


B070E01JM


2. Remove the old battery from the case and note the polarity. Make sure the polarity of the new battery is the same(+side facing down), then insert it in the transmitter.


B075E01JM-AAT


Panic Warning


PANIC


B070E02HP-AAT


Replacing the battery When the transmitter's battery begins to get weak, it may take several pushes on the button to lock or unlock the doors. Replace the battery as soon as possible.


Battery type : CR2032


Replacement instructions:


B075E01JM 1. Push the "PANIC" button on the back


side of the transmitter.


2. At the same time, the siren will sound and the turn signal lights will blink for 30
seconds.


3. To turn off the system, push the "PANIC"


button again on the transmitter.


Screwdriver


B070E02JM


1. Carefully separate the case with a blade screwdriver as shown in the illustration.


1FEATURES OF YOUR HYUNDAI 12


POWER WINDOWS


B060A03Y-AAT


B060A03JM The power windows operate when the ignition key is in the "ON" position. The main switches are located on the driver's armrest and control the front and rear win- dows on both sides of the vehicle. The windows may be opened by depressing the appropriate window switch and closed by pulling up the switch. To open the win- dow on the driver's side, press the switch halfway down. The window moves as long as the switch is operated. To fully open the driver's window automatically, press the switch fully down. In automatic operation, the window will fully open even if you let go of the switch. To stop at the desired open- ing, pull up and release the switch.


HJM2017
In order to prevent operation of the pas- senger front and rear windows, a window lock switch is provided on the armrest of the driver's door. To disable the power windows, press the window lock switch. To revert to normal operation, press the win- dow lock switch a second time.


NOTE: The power windows can be operated for 30 seconds after the ignition key is turned to the "ACC" or "LOCK" posi- tions, or removed from the ignition switch. If the front doors are opened during this 30 second period, the power windows can no longer be operated without the ignition key turned to the "ON" position.


Close


Open


HJM2016


WARNING:


(1)Be careful that someone's head, hands and body are not trapped by a closing window.


(2)Never try to operate the main switch on the driver's door and the individual door window switch in opposing di- rections at the same time. If this is done, the window will stop and cannot be opened or closed.


(3)Do not leave children alone in the car. Always remove the ignition key for their safety.


SEATS


B080A02A-AAT


ADJUSTABLE FRONT SEATS


! WARNING:


o Never adjust the driver’s seat while the vehicle is moving. Any sudden or unexpected movement of the seat could cause you to lose control of the vehicle resulting in an accident. Only adjust the driver’s seat when the ve- hicle is stationary.


o Do not sit or lean unnecessarily close to the airbag. Position the seat so that you can sit as far back as possible from the airbag and still comfortably reach all controls.


FEATURES OF YOUR HYUNDAI


13


B080B03A-AAT


Adjusting Seat Forward and Rear- ward


WARNING:


After adjusting the seat, always check that it is securely locked into place by attempting to move the seat forward or reverse without using the lock release lever. Sudden or unexpected move- ment of the driver's seat could cause you to lose control of the vehicle result- ing in an accident.


B080C03A-AAT


Adjusting Seatback Angle


OJM019001
To move the seat toward the front or rear, pull the lock release lever upward. This will release the seat on its track so you can move it forward or rearward to the desired position. When you find the position you want, release the lever and slide the seat forward or rearward on its track until it locks into the desired position and cannot be moved further.


OJM019002


To recline the seatback, lean forward to take your weight off it, then pull up on the recliner control lever at the outside edge of the seat.


1FEATURES OF YOUR HYUNDAI 14


Now lean back until the desired seatback angle is achieved. To lock the seatback into position, release the recliner control lever.


! WARNING:


Riding with a reclined seatback in- creases your chance of serious or fatal injuries in the event of a collision or sudden stop. The protection of your restraint system (seat belts and airbags) is greatly reduced by reclining your seat. Seat belts must be snug against your hips and chest to work properly. The more the seatback is reclined, the greater the chance that an occupant's hips will slide under the lap belt or the occupant's neck will strike the shoulder belt. Driv- ers and passengers should always sit well back in their seats, properly belted, and with the seatbacks upright.


B080D02JM-AAT


Adjustable Headrests


B080E01JM-GAT


Forward and backward adjustment (if installed)


Lock Knob


HJM2044


Headrests are designed to help reduce the risk of neck injuries. To raise the headrest, pull it up. To lower the headrest, push it down while pressing the lock knob. To remove the headrest, raise it as far as it can go then press the lock knob while pulling upward. This should only be done when the seat is not occu- pied.


HJM2045-2


The headrest may be adjusted forward to three different positions by pulling the headrest forward. To adjust the headrest backward, pull it fully forward to the farthest position and release it. Adjust the headrest so that it properly supports the head and neck.


!


WARNING:


B083D01NF-AAT


Active Headrests (If Installed)


B080F02A-AAT


Seat Cushion Height Adjustment (Driver's Seat Only) (If Installed)


FEATURES OF YOUR HYUNDAI


15


HNF2041-1
The active headrest is designed to move forward and upward during a rear impact. This helps to prevent the driver's and front passenger's head from moving backward and thus helps prevent neck injuries.


OJM019003
To change the height of the seat cushion, rotate the knob located on the outside of the seat cushion.


B080D01JM


o For maximum effectiveness in case of an accident the headrest should be adjusted so the middle of the head- rest is at the same height as the top of the occupant's eyes. For this reason, the use of a cushion that holds the body away from the seatback is not recommended.


o Do not operate vehicle with the head- rests removed as injury to the occu- pants may occur in the event of an accident. Headrests may provide pro- tection against neck injuries when properly adjusted.


o Do not adjust the headrest hejght while


the vehicle is in motion.


! WARNING:


It is recommended that the seat heater not be used when elderly people or people who are ill occupy the seat. Also, do not use the seat warmer if the occupant is sleeping.


1FEATURES OF YOUR HYUNDAI 16


B080E01F-AAT


Lumbar Support Control (Driver's seat only) (If Installed)


B100A02JM-AAT


SEAT WARMER (If installed)


SOFT


FIRM


OJM019004


The driver's seat is equipped with adjust- able lumbar support. To increase the amount of lumbar support, pull the lever forward. To decrease it, push the lever toward the rear.


HJM2042
The seat warmer is provided to warm the front seats during cold weather. With the ignition key in the "ON" position, push either of the switches to warm the driver's seat or the passenger's seat. During mild weather or under conditions where the operation of the seat warmer is not needed, keep the switches in the "OFF" position.


NOTE: o The seat warmer will not operate if the ambient temperature is higher than 82.4°F ± 6.3°F (28°C ± 3.5°C).


o If the seat warmer doesn't work when ambient temperature is lower than 75.2°F (24°C), it should be checked at an authorized dealer.


B085A01JM-GAT


REAR SEAT Adjusting Seatback Angle


B085B02JM-AAT


Folding Rear Seatback For convenience, the seatbacks and seat cushions may be folded down and up.


Seatback folding lever


OJM019005
To recline the seatback, pull the seatback folding lever and release it after the de- sired seatback angle is achieved. When you recline the seatback to desired position, always be sure it has locked into position.


OJM019006
1. Pull the seatback folding lever then


push down the seatback.


2. Be sure it has locked into position to


listen an audible "Click".


FEATURES OF YOUR HYUNDAI


17


HJM2048


NOTE: o Before folding the seatback, place the rear seat belt buckles in the buckle pouch on the seatback. This will pre- vent the seat belt buckles from be- coming covered by the seat cushion when it is returned to the seating po- sition.


CAUTION:


When reclining the seatback, you should adjust the seatback folding lever while standing.


CAUTION:


Be careful not to overload seatback. Overloading may cause damage the seatback.


3. To return the seatback to its normal position, pull the seatback folding lever and reverse the above procedure.


1FEATURES OF YOUR HYUNDAI 18


o When you return the seatback to its upright position, always be sure it is locked into position by pulling and push- ing on the top of the seatback.


WARNING:


o The purpose of the fold-down rear seat back is to allow you to carry larger items than could otherwise be accommodated. Never allow passen- gers to sit on the cargo area while the car is moving. This is not a proper seating position and no seat belts are available for use when the seat back is folded down. This could result in serious injury or death in case of an accident or a sudden stop. Objects should not ex- tend higher than the top of the front seatbacks. This could allow cargo to slide for- ward and cause injury or damage during sudden stops.


o When you return the rear seatback to its upright position after being folded down, be careful not to damage the seatbelt webbing or buckle. In addi- tion, do not allow the seatbelt webbing or buckle to get caught or pinched in the rear seat.


WARNING:


o When you return the rear seatback to its upright position, be sure it is locked into position. Attempt to move it.


o Never attempt to fold or return seat


while the vehicle is moving.


B140A01B-AAT


REAR SEAT WARNING


B140A01JM For the safety of all passengers, luggage or other cargo should not be piled higher than the top of the seatback.


SEAT BELTS


B150A02S-AAT


SEAT BELT PRECAUTIONS


WARNING:


All occupants of the vehicle must wear their seat belts at all times. Seat belts and child restraints reduce the risk of serious or fatal injuries for all occupants in the event of a collision or sudden stop. Without a seat belt, occupants could be shifted too close to a deploying airbag, strike the interior structure or be thrown from the vehicle. Properly worn seat belts greatly reduce these hazards. Even with advanced airbags, unbelted occu- pants can be severely injured by a de- ploying airbag. Always follow the pre- cautions about seat belts, airbags and occupant safety contained in this manual.


B150B04Y-AAT


Infant or Small Child All 50 states have child restraint laws. You should be aware of the specific require- ments in your state. Child and/or infant safety seats must be properly placed and installed in the rear seat. Information about the use of these restraints begins on page 1-26.


! WARNING:


Every person in your vehicle needs to be properly restrained at all times, includ- ing infants and children. Never hold a child in your arms or lap when riding in a vehicle. The violent forces created dur- ing a crash will tear the child from your arms and throw the child against the interior. Always use a child restraint appropriate for your child's height and weight, see page 1-26.


NOTE: Small children are best protected from injury in an accident when properly re- strained in the rear seat by a child re- straint system that meets the require- ments of the Federal Motor Vehicle Safety Standards. Before buying any child restraint system, make sure that it has a label certifying that it meets Fed- eral Motor Vehicle Safety Standard 213. The restraint must be appropriate for your child's height and weight. Check the label on the child restraint for this information. See page 1-26.


FEATURES OF YOUR HYUNDAI


19


B150C02A-AAT


Larger Children Children who are too large for child re- straint systems should always occupy the rear seat and use the available lap/shoul- der belts. The lap portion should be fas- tened snug on the hips and as low as possible. Check belt fit periodically. A child's squirming could put the belt out of position. Children are afforded the most safety in the event of an accident when they are restrained by a proper restraint system in the rear seat. If a larger child (over age 13) must be seated in the front seat, the child should be securely re- strained by the available lap/shoulder belt and the seat should be placed in the rearmost position. Children under the age of 13 should be restrained securely in the rear seat. NEVER place a child under the age of 13 in the front seat. NEVER place a rear facing child seat in the front seat of a vehicle.


B150D01A-AAT


Pregnant Women The use of a seat belt is recommended for pregnant women to lessen the chance of injury in an accident. When a seat belt is used, the lap belt portion should be placed as low and snugly as possible on the hips, not across the abdomen. For specific rec- ommendations, consult a physician.


1FEATURES OF YOUR HYUNDAI 20


B150E01A-AAT


Injured Person A seat belt should be used when an injured person is being transported. When this is necessary, you should consult a physician for recommendations.


B150F01A-AAT


One Person Per Belt Two people (including children) should never attempt to use a single seat belt. This could increase the severity of injuries in case of an accident.


B150G02A-AAT


Do Not Lie Down To reduce the chance of injuries in the event of an accident and to achieve maxi- mum effectiveness of the restraint system, all passengers should be sitting up and the front seats should be in an upright position when the car is moving. A seat belt cannot provide proper protection if the person is lying down in the rear seat or if the front seat is in a reclined position.


WARNING:


Riding with a reclined seatback in- creases your chance of serious or fatal injuries in the event of a collision or sudden stop. The protection of your restraint system (seat belts and airbags) is greatly reduced by reclining your seat. Seat belts must be snug against your hips and chest to work properly. The more the seatback is reclined, the greater the chance that an occupant's hips will slide under the lap belt causing serious internal injuries or the occupant's neck could strike the shoulder belt. Drivers and passengers should always sit well back in their seats, properly belted (see page 1-22), and with the seatbacks up- right.


B160A02A-AAT


CARE OF SEAT BELTS Seat belt systems should never be disas- sembled or modified. In addition, care should be taken to assure that seat belts and belt hardware are not damaged by seat hinges, doors or other abuse.


WARNING:


When you return the rear seatback to its upright position after the rear seatback was folded down, be careful not to dam- age the seat belt webbing or buckle. Be sure that the webbing or buckle does not get caught or pinched in the rear seat. A seat belt with damaged webbing or buckle will not be as strong and could possibly fail during a collision or sudden stop, resulting in serious injury.


B160B01A-AAT


Periodic Inspection It is recommended that all seat belts be inspected periodically for wear or damage of any kind. Parts of the system that are damaged should be replaced as soon as possible.


FEATURES OF YOUR HYUNDAI


21


Release the button to lock the anchor into position. Try sliding the height adjuster to make sure that it has locked into the posi- tion.


! WARNING:


o Verify the shoulder belt anchor is locked into position at the appropriate height. Never position the shoulder belt across your neck or face. Im- properly positioned seat belts can cause serious injuries in an accident. o Failure to replace seat belts after an accident could leave you with dam- aged seat belts that will not provide protection in the event of another collision leading to personal injury or death. Replace your seat belts after being in an accident as soon as pos- sible.


B160C01A-AAT


Keep Belts Clean and Dry Seat belts should be kept clean and dry. If belts become dirty, they can be cleaned by using a mild soap solution and warm wa- ter. Bleach, dye, strong detergents or abra- sives should not be used because they may damage and weaken the fabric.


B160D01A-AAT


When to Replace Seat Belts Entire in-use seat belt assembly or assem- blies should be replaced if the vehicle has been involved in an accident. This should be done even if no damage is visible. Additional questions concerning seat belt operation should be directed to your Hyundai Dealer.


B170A05Y-AAT


HEIGHT ADJUSTABLE FRONT SEAT SHOULDER BELT


HJM2050


You can adjust the height of the shoulder belt anchor to one of the 4 positions for maximum comfort and safety. If the height of the adjusting seat belt is too near your neck, you will not be getting the most effective protection. The shoulder portion should be adjusted so that it lies across your chest and midway over your shoulder nearest the door and not your neck. To adjust the height of the seat belt anchor, lower or raise the height adjuster into an appropriate position. To raise the height adjuster, pull it up. To lower it, push it down while pressing the height adjuster button.


1FEATURES OF YOUR HYUNDAI 22


B180A02A-AAT


SEAT BELT-Driver's 3-Point System with Emergency Locking Retractor To Fasten Your Belt


NOTE: o If you are not able to pull out the safety belt from the retractor, firmly pull the belt out and release it. Then you will be able to pull the belt out smoothly.


o If the driver's seat belt is not fastened when the ignition key is in the "ON" position, the seat belt warning light will flash and the warning chime will sound for approximately six seconds.


B180A01L To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle. There will be an audible "click" when the tab locks into the buckle. The seat belt automatically adjusts to the proper length only after the lap belt portion is adjusted manually so that it fits snugly around your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. If there is a sudden stop or impact, however, the belt will lock into position. It will also lock if you try to lean forward too quickly.


B190A02Y-AAT


SEAT BELTS-Front Passenger and Rear Seat 3-Point System with Com- bination Locking Retractor Combination retractor type seat belts are installed in the rear seat positions to help accommodate the installation of child re- straint systems. Although a combination retractor is also installed in the front passen- ger seat position, Hyundai strongly recom- mends that children always be seated in the rear seat. NEVER place any infant restraint system in the front seat of the vehicle. This type of seat belt combines the fea- tures of both an emergency locking retrac- tor seat belt and an automatic locking retractor seat belt. To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle. There will be an audible "click" when the tab locks into the buckle. When not securing a child restraint, the seat belt operates in the same way as the driver's seat belt (Emergency Locking Retractor Type). It automatically adjusts to the proper length only after the lap belt portion of the seat belt is adjusted manu- ally so that it fits snugly around your hips. When the seat belt is fully extended from the retractor to allow the installation of a child restraint system, the seat belt opera- tion changes to allow the belt to retract, but not to extend (Automatic Locking Retrac- tor Type). See page 1-30.


NOTE: Although the combination retractor pro- vides the same level of protection for seated passengers in either emergency or automatic locking modes, it is recom- mended that seated passengers use the emergency locking feature for improved convenience. The automatic locking function is intended to facilitate child restraint installation. To convert from the automatic locking feature to the emergency locking operation mode, al- low the unbuckled seat belt to fully re- tract.


WARNING:


o For maximum restraint system pro- tection, the seat belts must always be used whenever the car is moving.


o Seat belts are most effective when seatbacks are in the upright position. o Children age 12 and younger must always be properly restrained in the rear seat. Never allow children to ride in the front passenger seat. If a child over 13 must be seated in the front seat, he/she must be properly belted and the seat should be moved as far back as possible.


FEATURES OF YOUR HYUNDAI


23


WARNING:


B200A01A-AAT


Adjusting Your Seat Belt


o Never wear the shoulder belt under your arm or behind your back. An improperly positioned shoulder belt can cause serious injuries in a crash. The shoulder belt should be positioned midway over your shoulder across your collarbone.


o Avoid wearing twisted seat belts. A twisted belt can't do its job as well. In a collision, it could even cut into you. Be sure the belt webbing is straight and not twisted.


o Be careful not to damage the belt webbing or hardware. If the belt web- bing or hardware is damaged, replace it.


B200A01L


WARNING:


You should place the lap belt portion as low as possible and snugly across your hips, not on your waist. If the lap belt is located too high on your waist, it may increase the chance of injury in the event of a collision. Both arms should not be under or over the belt. Rather, one should be over and the other under, as shown in the illustration. Never wear the seat belt under the arm nearest the door.


1FEATURES OF YOUR HYUNDAI 24


B210A01A-AAT


To Release the Seat Belt


B210A01L The seat belt is released by pressing the release button in the locking buckle. When it is released, the belt should automatically draw back into the retractor. If this does not happen, check the belt to be sure it is not twisted, then try again.


B220A02JM-AAT


SEAT BELTS - Center Rear Seat 3- Point System With Combination Locking Retractor


If there is a sudden stop or impact, the belt will lock into position. It will also lock if you try to lean forward too quickly.


(c)


(a)


(b)


(d)


B220A01JM-A 1. Before fastening the rear seat center belt, confirm the metal tab (a) and buckle (b) are latched together.


2. After confirming that (a) and (b) are latched, pull the seat belt out of the retractor and insert the metal tab (c) into the buckle (d).


There will be an audible "click" when the tab locks in the buckle. The seat belt auto- matically adjusts to the proper length only after the lap belt is adjusted manually so that it fits snugly around your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around.


B220A02Y


! WARNING:


o Never let anyone ride in the rear cen- ter seat without fastening all metal tabs and buckles as described in this section. This seat belt is designed to function as a typical 3-point restraint (lap/shoulder belt). Using only the shoulder portion or lap portion of the belt can result in serious or fatal inju- ries in the event of a collision or sud- den stop.


!


WARNING:


o Never unlock the metal tab (a) and the buckle (b) with the following excep- tions. (1)In case of folding rear seatbacks


down.


(2)If transporting an object on the rear seat may cause damage to the rear seat center belt.


o Always lock metal tab (a) into buckle (b) immediately after returning the rear seatbacks to an upright position. This portion of the rear center seat belt should only be unbuckled when the rear seatback is folded down.


! WARNING:


o In case of unlocking metal tab (a) and the buckle (b), place metal (a) in the seat belt clip not to make noise while driving.


To disconnect the metal tab (a) from the buckle (b) , insert a narrow-ended tool into the groove located on the buckle (b).


FEATURES OF YOUR HYUNDAI


25


B220C01Y-AAT


To Release the Seat Belt


B220C01JM When you want to release the seat belt, press the button in the locking buckle.


WARNING:


The rear seat center belt latching mecha- nism is different from those for the out- board rear seat shoulder belts. When fastening the outboard rear seat shoul- der belts or the rear seat center belt, make sure they are inserted into the correct buckles to obtain maximum pro- tection from the seat belt system and assure proper operation.


B220A02JM


1FEATURES OF YOUR HYUNDAI 26


CHILD RESTRAINT SYSTEM


B230A05O-AAT Children riding in the car should sit in the rear seat and must always be properly restrained to minimize the risk of injury in an accident, sudden stop or sudden ma- neuver. According to accident statistics provided by the National Highway Traffic Safety Administration (NHTSA), children are safer when properly restrained in the rear seats than in the front seat. Larger children not in a child restraint should use one of the seat belts provided. All 50 states have child restraint laws. You should be aware of the specific require- ments in your state. Child and/or infant safety seats must be properly placed and installed in the rear seat. You must use a commercially available child restraint sys- tem that meets the requirements of the Federal Motor Vehicle Safety Standards (FMVSS). Child restraint systems are de- signed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/ shoulder belt, or by a ISOFIX system (if installed). Children could be injured or killed in a crash if their restraints are not properly secured. For small children and babies, a child seat or infant seat must be used. Before buying a particular child restraint system, make sure it fits your car seat and seat belts, and fits your child. Follow all the instructions provided by the manufacturer when installing the child restraint system.


! WARNING:


o A child restraint system must be placed in the rear seat. Never install a child or infant seat on the front passenger's seat. Should an accident occur and cause the passenger side airbag to deploy, it could severely injure or kill an infant or child seated in an infant or child seat. Thus only use a child restraint in the rear seat of your vehicle.


o A safety belt or child restraint system can become very hot if it is left in a closed vehicle on a sunny day, even if the outside temperature does not feel hot. Be sure to check the seat cover and buckles before placing a child there.


o When the child restraint system is not in use, store it in the luggage compart- ment or fasten it with a safety belt so that it will not be thrown forward in the case of a sudden stop or an accident. o Children may be seriously injured or killed by an inflating airbag. All chil- dren, even those too large for child restraints, must ride in the rear seat.


WARNING:


To reduce the chance or serious or fatal injuries: o Children of all ages are safer when restrained in the rear seat. A child riding in the front passenger seat can be forcefully struck by an inflating airbag resulting in serious or fatal injuries.


o Always follow the instructions for in- stallation and use of the child restraint maker.


o Always make sure the child seat is secured properly in the car and your child is securely restrained in the child seat.


o Never hold a child in your arms or lap when riding in a vehicle. The violent forces created during a crash will tear the child from your arms and throw the child against the car’s interior.


o Never put a seat belt over yourself and a child. During a crash, the belt could press deep into the child caus- ing serious internal injuries.


!


WARNING:


o Never leave children unattended in a vehicle – not even for a short time. The car can heat up very quickly, resulting in serious injuries to chil- dren inside. Even very young chil- dren may inadvertently cause the vehicle to move, entangle themselves in the windows, or lock themselves or others inside the vehicle.


o Never allow two children, or any two persons, to use the same seat belt. o Children often squirm and reposition themselves improperly. Never let a child ride with the shoulder belt under their arm or behind their back. Al- ways properly position and secure children in rear seat.


o Never allow a child to stand-up or kneel on the seat or floorboard of a moving vehicle. During a collision or sudden stop, the child can be violently thrown against the vehicles interior, resulting in serious injury.


o Never use an infant carrier or a child safety seat that "hooks" over a seatback, it may not provide adequate security in an accident.


FEATURES OF YOUR HYUNDAI


27


B230C07O-AAT


Installing a Child Restraint Seat with the "Tether Anchorage" System Three child restraint hook holders are lo- cated on the rear luggage compartment floor.


This symbol indicates the location of each user ready tether anchorage.


B230C04JM


! WARNING:


o Seat belts can become very hot, es- pecially when the car is parked in direct sunlight. Always check seat belt buckles before fastening them over a child.


o Always store or secure a child seat, even when it is not in use. During a collision or sudden stop, the child seat could be thrown inside the ve- hicle.


B230B01E-AAT


Using a Child Restraint System For small children and babies, the use of a child seat or infant seat is required. This child seat or infant seat should be of appro- priate size for the child and should be installed the manufacturer's instructions. It is further required that the seat be placed in the vehicle's rear seat since this can make an important contribution to safety. Your ve- hicle is provided with three child restraint hook holders for installing the child seat or infant seat.


in accordance with


1FEATURES OF YOUR HYUNDAI 28


To install the child restraint seat tether


Rear luggage compartment floor


Tether anchor cover


Child Restraint Hook Holder


B230C05JM


1. Open the tether anchor cover on the


rear luggage compartment floor.


Child Restraint Hook Holders


Tether Strap Hook


Front of Vehicle


B230B01JM


2. Route the child restraint seat tether strap


over the seatback.


For vehicles with adjustable headrests, route the tether strap under the head- rest and between the headrest posts, otherwise route the tether strap over the top of the seatback.


3. Connect the tether strap hook to the child restraint hook holder and tighten to secure the seat.


WARNING:


o Install the Child Restraint Seat fully rearward against the seatback, with the seatback reclined two positions from the most upright latched posi- tion.


o A child can be seriously injured or killed in a collision if the child restraint is not properly anchored. Always follow the child seat manufacturer’s instructions for installation and use.


! WARNING:


o Never mount more than one child re- straint to a single tether or to a single lower anchorage point. The increased load caused by multiple seats may cause the tethers or anchorage points to break, causing serious injury or death.


B230D06E-AAT


Securing the Child Restraint Seat with the Child Seat Lower Anchor system


B230D01JM


Some child seat manufacturers make safety seats that are labeled as LATCH or LATCH- compatible child seats.


LATCH stands for "Lower anchors and Tethers for Children". These seats include two rigid or webbing mounted attachments that connect to two LATCH anchors at specific seating posi- tions in your vehicle. This type of child seat eliminates the need to use seat belts to attach the child seat for forward-facing child seats. LATCH anchors have been provided in your vehicle. The LATCH anchors are lo- cated in the left and right outboard rear seating positions. Their locations are shown in the illustration. There is no LATCH anchor provided for the center rear seating position.


! WARNING:


o A child can be seriously injured or killed in a collision if the child restraint is not properly anchored. Always follow the child seat manufacturer’s instructions for installation and use. o Never install a child restraint using the LATCH anchors at the center po- sition of the rear seat. In a crash, the LATCH anchors may break if a car seat is improperly placed in the cen- ter position resulting in serious or fatal injuries.


FEATURES OF YOUR HYUNDAI


29


WARNING:


Only place a LATCH or LATCH-com- patible child seat in the left or right out- board rear seating positions (as shown) to the appropriate LATCH anchors provided.


o Never mount more than one child re- straint to a single tether or to a single lower anchorage point. The increased load caused by multiple seats may cause the tethers or anchorage points to break, causing serious injury or death.


o When using the vehicle’s “LATCH” system to install a child restraint sys- tem in the rear seat, all unused ve- hicle rear seat belt metal latch plates or tabs must be latched securely in their seat belt buckles and the seat belt webbing must be retracted be- hind the child restraint to prevent the child from reaching and taking hold of unretracted seat belts. Unlatched metal latch plates or tabs may allow the child to reach the unretracted seat belts which may result in strangula- tion and a serious injury or death to the child in the child restraint.


1FEATURES OF YOUR HYUNDAI 30


Lower Anchor Position Indicator


Lower Anchor


B230D02JM


Child restraint symbols are located on the left and right rear seat backs to indicate the position of the lower anchors for child restraints.


B230D03JM


B230F01JM-AAT


Child Restraint System Installation on Rear Seat Center Position


Follow the child seat manufacturer's in- structions to properly install safety seats with LATCH or LATCH-compatible attach- ments.


Once you have installed the LATCH child restraint seat, assure that the seat is prop- erly attached to the LATCH and tether anchors. Also, test the safety seat before you place the child in it. Tilt the seat from side to side. Also try to tug the seat forward. Check to see if the anchors hold the seat in place.


CAUTION:


Do not allow the rear seat belt webbing to get scratched or pinched by the LATCH- seat latch and LATCH anchor during the installation.


WARNING:


A child can be seriously injured or killed in a collision if the child restraint is not properly anchored to the car and the child is not properly restrained in the child restraint. Always follow the child seat manufacturer’s instructions for in- stallation and use.


B235G02JM To install a child restraint system in the center rear seat, extend the shoulder/lap belt entirely from its retractor until a "click" is felt. This will engage the seat belt retrac- tor automatic locking feature, which allows the seat belt to retract but not extend. Install the child restraint system, buckle the seat belt and allow the seat belt to take up any slack. Make sure that the lap portion of the belt is tight around the child restraint sys- tem and the shoulder portion of the belt is positioned so that it can not interfere with the child's head or neck. Also, double check to be sure that the retractor has engaged the Automatic Locking feature by trying to extend webbing out of the retrac- tor. If the retractor is in the Automatic Lock- ing mode, the belt will be locked.


FEATURES OF YOUR HYUNDAI


Loading...
x