Login- 2004 Hyundai Tiburon Owners Manuals
- Hyundai Tiburon Owners Manuals
- 2005 Hyundai Tiburon Owners Manuals
- Hyundai Tiburon Owners Manuals
- 2003 Hyundai Tiburon Owners Manuals
- Hyundai Tiburon Owners Manuals
- 2008 Hyundai Tiburon Owners Manuals
- Hyundai Tiburon Owners Manuals
- 2006 Hyundai Tiburon Owners Manuals
- Hyundai Tiburon Owners Manuals
- Download PDF Manual
-
o Station Swapping - As an FM signal weak- ens, another more powerful signal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.
o Multi-Path Cancellation - Radio signals being received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this occurs, select another station until the condition has passed.
1FEATURES OF YOUR HYUNDAI 90
AUDIO SYSTEM
H240A01O-GAT STEREO RADIO OPERATION (H250) (If Installed)
5. BAND Selector
3. TREBLE/FADER Control Knob
(TREB/FAD)
4. TUNE/SEEK Select Button 1. POWER ON/OFF, VOLUME Control Knob
6. PRESET Buttons
2. BASS/BALANCE Control Knob
(BASS/BAL)
7. SCAN Button
H250A01GK
H240B02A-GAT 1. POWER ON-OFF Control
Knob
The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the tape direction indicator in the tape mode. To switch the power off, press the knob again.
VOLUME Control
Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.
2. BASS Control Knob
Press to pop the knob out and turn to the left or right for the desired bass tone.
BAL (Balance Control) Knob
Pull the bass control knob further out. Turn the control knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclock- wise, left speaker sound will be emphasized (right speaker sound will be attenuated).
3. TREB (Treble Control) Knob
5. BAND Selector
FEATURES OF YOUR HYUNDAI
91
Press to pop the knob out and turn to the left or right for the desired treble tone.
FAD (Fader Control) Knob
Pull the treble control knob further out. Turn the control knob counterclockwise to emphasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be emphasized (front speaker sound will be attenuated).
4. TUNE (Manual) Select Button
Press the side or side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.
SEEK Operation (Automatic Channel Selection)
Press the TUNE select button 1 sec or more.Releasing it will automatically tune to the next available station with a beep sound. When the side is pressed longer than 1 second, releasing will automatically tune to the next higher frequency and when the side is pressed longer than 1 second, releasing will automati- cally tune to the next lower frequency.
Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is displayed on LCD.
FM/AM
6. PRESET STATION SELECT Button
Six (6) stations for AM, FM1 and FM2 respec- tively can be preset in the electronic memory circuit on this unit.
HOW TO PRESET STATIONS
Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:
o Press band selector to set the band for AM,
FM1, or FM2.
o Select the desired station to be stored by
seek or manual tuning.
o Determine the preset station select button
you wish to use to access that station.
1FEATURES OF YOUR HYUNDAI 92
o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory with a beep sound. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.
o When completed, any preset station may be recalled by selecting AM, FM1 or FM2 band and the appropriate station button.
7. SCAN Button
When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.
CAUTION:
o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.
FEATURES OF YOUR HYUNDAI
93
H240C01O-GAT CASSETTE TAPE PLAYER OPERATION (H250) (If Installed)
3. TAPE PROGRAM Button
6. TAPE SLOT
2. AUTO MUSIC SELECT Button
4. EJECT Button
1.
FF/REW Button
5. DOLBY SELECT Button
H240C01GK
1FEATURES OF YOUR HYUNDAI 94
H240A02O-AAT 1. FF/REW Button
o The FF (fast forward tape winding) starts when the button is pressed during PLAY or REW.
o The PLAY starts when the button is
pressed again during FF.
o The REW (rewinding) starts when the button is pressed during PLAY or FF.
o The PLAY starts when the button is
pressed again during REW.
NOTE: When tape operation is abnormal or ER8
fault code is displayed, press the eject button more than 5 seconds to reset the deck function.4. EJECT Button
o When the EJECT button is pressed with a
cassette loaded, the cassette will eject.
o When the EJECT button is pressed during
FF/REW, the cassette will eject.
2. AUTO MUSIC SELECT Button Press the button to find the starting point of each song in a prerecorded music tape. The quiet space between songs (must have at least a 4 sec. gap) can be identified by the AUTO MUSIC SELECT button.
5. DOLBY SELECT Button
If you get background noise during PLAY, you can reduce this considerably by merely press- ing DOLBY SELECT button. If you want to release, press the button again.
o Pressing the button will play the beginning
of the next music segment.
o Pressing the button will start replay at the beginning of the music just listened to.
3. TAPE PROGRAM Button
This allows you to play the reverse side of the tape by merely depressing the program button. An arrow will appear in the display to show tape direction.
CAUTION:
o Do not insert anything like coins into the player slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
o Do not impact on the audio system, or the playback mechanism could be dam- aged.
FEATURES OF YOUR HYUNDAI
95
H260A01O-AAT STEREO RADIO OPERATION (H260) (If installed)
3. BASS/TREBLE Control Knob
4. SCAN Button
6. BAND Selector
2. FADER Control Knob
7. PRESET Buttons
5. TUNE/SEEK Select Button
1. POWER ON-OFF/VOLUME/BALANCE Control Knob
H260A01GK
1FEATURES OF YOUR HYUNDAI 96
H260B03E-AAT 1. POWER ON-OFF Control Knob
The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the CD track indicator in either the CD mode or CD AUTO CHANGER mode. To switch the power off, press the knob again.
VOLUME Control
Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.
BALANCE Control
Pull and turn the control knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).
2. FAD (Fader Control) Knob
5. TUNE (Manual) Select Button
Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.
SEEK Operation (Automatic Channel Selection)
Press the TUNE select button for 1 sec or more. Releasing it will automatically tune to the next available station with a beep sound. When the ( ) side is pressed longer than 1
second, releasing will automatically tune to the next higher frequency and when the ( ) side is pressed longer than 1 second, releasing will automatically tune to the next lower frequency.Turn the control knob counterclockwise to emphasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be emphasized (front speaker sound will be attenuated).
3. BASS Control Knob
Press to pop the knob out and turn to the left or right for the desired bass tone.
TREB (Treble Control) Knob
Pull the bass control knob further out. Turn to the left or right for the desired treble tone.
4. SCAN Button
When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.
FEATURES OF YOUR HYUNDAI
97
CAUTION:
o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.
6. BAND Selector
FM/AM
Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is displayed on LCD.
7. PRESET STATION SELECT Button
Six (6) stations for AM, FM1 or FM2 respec- tively can be preset in the electronic memory circuit on this unit.
HOW TO PRESET STATIONS
Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:
o Press band selector to set the band for AM,
FM1 or FM2.
o Select the desired station to be stored by
seek, scan or manual tuning.
o Determine the preset station select button
you wish to use to access that station.
o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.
o When completed, any preset station may be recalled by selecting AM, FM1 or FM2 band and the appropriate station button.
1FEATURES OF YOUR HYUNDAI 98
H260B01O-AAT COMPACT DISC PLAYER OPERATION (H260) (If installed)
4. SCAN Button
1. Playing CD
3. TRACK UP/DOWN
6. EJECT Button
2. FF/REW Button
5. REPEAT Button
H260B01GK
B260D03O-AAT 1. Playing CD
o Insert the CD with the label facing upward. o Insert the CD to start CD playback, during
radio operation.
o When a disc is in the CD deck, if you press the CD button, the CD player will begin playing even if the radio is being used.
o The CD player can be used when the ignition switch is in either the "ON" or "ACC" position.
2. FF/REW ( / )
If you want to fast forward or reverse through the compact disc track, push and hold the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.
3. TRACK UP/DOWN
o The desired track on the disc currently being played can be selected using the track number.
o Press once to skip forward to the beginn- ing of the next track. Press once to skip back to the beginning of the track.
4. SCAN Button
o Press the SCAN button to playback the first
10 seconds of each track.
o Press the SCAN button again within 10 sec. When you have reached the desired track.
5. REPEAT Button
o To repeat the track you are currently listen- ing to, press the RPT button. To cancel , press again.
o If you do not release RPT operation when the track ends, it will automatically be replayed. This process will be continued until you push the button again.
6. EJECT Button
When the EJECT button is pressed with a CD loaded, the CD will eject.
FEATURES OF YOUR HYUNDAI
99
NOTE: o If the CD does not operate properly or if the ER2 fault code is displayed, use one of two methods to reset the CD deck function. - Remove the audio fuse for 5 minutes.
Then, reinstall the audio fuse.
- Disconnect the negative terminal of the battery and wait 5 minutes. Then reconnect the negative battery termi- nal.
o To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle’s air conditioning or heating system.
o When replacing the fuse, replace it with
a fuse having the correct capacity.
o The preset station frequencies are all erased when the car battery is discon- nected. Therefore, all data will have to be set again if this should occur.
o Do not add any oil to the rotating parts. Keep magnets, screwdrivers and other metallic objects away from the tape mechanism and head.
o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.
1FEATURES OF YOUR HYUNDAI 100
o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.
o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.
o Do not expose this equipment (includ- ing the speakers) to water or excessive moisture.
o Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism. These can cause poor disc scratching to occur or trouble in the compact disc player.
o Avoid using CD-Recordable or CD- Rewritable to ensure proper operation. When using the compact disc player, genuine CDs are recommended.
CAUTION:
o Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.
o Do not insert anything like coins into the player slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
o Do not impact on the audio system, or the playback mechanism could be dam- aged.
o Driving off-road or other vibrations may
skip your compact disc. Do not use the audio system off-road as the discs could be scratched and dam- aged.
B260E01E-AAT CD AUTO CHANGER (H260) (If installed)
6. SCAN Button
1. CD Select Button
3. TRACK UP/DOWN
FEATURES OF YOUR HYUNDAI
101
4. FF/REW Button
5. REPEAT Button
2. DISC Select Button
H260E01GK
1FEATURES OF YOUR HYUNDAI 102
B260F01GK-AAT The CD auto changer is located in the right side of the quater trim.
o To use the CD auto changer.
1. Open the sliding lid of the CD auto changer. 2. To eject the compact disc magazine, press the EJECT button located inside the CD auto changer. Insert the discs into the magazine.
3. 4. Push the magazine into the CD auto changer
and close the sliding lid.
o The CD auto changer can be used when the ignition switch is in either the "ON" or "ACC" position.
1. CD Select Button
When the CD changer magazine contains discs, press the "CD" button and the CD changer can be used even if the radio is being used. The Hyundai CD changer can hold up to eight discs. The disc number will be lit, and the track number, and elapsed time will be displayed.
2. DISC Select Button
5. REPEAT
To select the CD you want, push " " to change the disc number.
TUNE DISC
3. TRACK UP/DOWN
o The desired track on the disc currently being played can be selected using the track number.
o Press once to skip forward to the begin- ning of the next track. Press once to skip back to the beginning of the track.
4. FF/REW ( / )
If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.
o To repeat the music you are listening to, press the RPT button. To cancel, press again.
o If you do not release RPT operation when the track ends, it will automatically be replayed. This process will be continued until you push the button again.
6. SCAN Button
o Press the SCAN button to playback the first
10 seconds of each track.
o Press the SCAN button again within 10 sec.
for the desired track.
NOTE: o When replacing the fuse, replace it with
a fuse having the correct capacity.
o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.
o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.
o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.
FEATURES OF YOUR HYUNDAI
103
CAUTION:
o Do not insert warped or poor quality discs into the CD changer as damage to the unit may occur.
o Do not insert anything like coins into the changer slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
o Do not impact on the audio system, or the playback mechanism could be dam- aged.
o Driving off-road or other vibrations may
skip your compact disc. Do not use the audio system off-road as the discs could be scratched and dam- aged.
o Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism. These can cause disc scratching to oc- cur or trouble in the compact disc changer.
o Avoid using CD-Recordable or CD- Rewritable to ensure proper operation. When using the compact disc changer, genuine CDs are recommended.
1FEATURES OF YOUR HYUNDAI 104
H290A01FC-GAT STEREO RADIO OPERATION (H280) (If installed)
1. POWER ON/OFF VOLUME Control Knob
8. SCAN Button (If installed)
7. EQUALIZER Button
6. BAND Select Button
4. TUNE/SEEK Select Button
5. PRESET Buttons
H290A01GK
3. TREBLE/FAD Konb
2. BASS/BALANCE Control Knob
H290B03E-GAT 1. POWER ON-OFF Control Knob
The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the button to switch the power on. The display shows the radio frequency in the radio mode, the tape direction indicator in the tape mode or CD track in either the CD mode or CD AUTO CHANGER mode. To switch the power off, press the button again.
VOLUME Control
Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.
2. BASS/BALANCE Control Knob BASS Control Knob
Press to pop the knob out. To increase the bass, rotate the knob clockwise, while to decrease the bass, rotate the knob counterclockwise.
BALANCE Control knob
Pull the Bass control knob out further. Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclock- wise, left speaker sound will be emphasized (right speaker sound will be attenuated).
3. TREBLE/FAD Knob TREBLE Control Knob
Press to pop the knob out and turn to the left or right for the desired treble tone.
FAD (Fader Control) Knob
Pull the Treble control knob out further. Turn the control knob counterclockwise to emphasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be empha- sized (front speaker sound will be attenuated).
4. TUNE (Manual) Select Button
Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.
FEATURES OF YOUR HYUNDAI
105
SEEK Operation (Automatic Channel Selection)
Press the TUNE select button for 0.5 sec or more. Releasing it will automatically tune to the next available station with a beep sound. When the ( ) side is pressed longer than 0.5
second, releasing will automatically tune to the next higher frequency and when the ( ) side is pressed longer than 0.5 second, releasing will automatically tune to the next lower frequency.5. PRESET STATION Select Buttons
Six (6) stations for AM, FM and FM2 respec- tively can be preset in the electronic memory circuit.
HOW TO PRESET STATIONS
Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:
1FEATURES OF YOUR HYUNDAI 106
o Press band selector to set the band for AM,
FM or FM2.
o Select the desired station to be stored by
seek or manual tuning.
o Determine the preset station select button
you wish to use to access that station.
o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory with beep sound. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM station per button.
o When completed, any preset station may be recalled by selecting AM, FM or FM2 band and the appropriate station button.
6. BAND Selector
FM/AM
Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is shown on the display.
7. EQUALIZER Button
Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;
CLASSIC → JAZZ → ROCK → DEFEAT
8. SCAN Button (If installed)
When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.
CAUTION:
o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.
H290C01FC-GAT CASSETTE TAPE PLAYER OPERATION (H280) (If installed)
FEATURES OF YOUR HYUNDAI
107
5. EQUALIZER Button
4. TAPE EJECT Button 2. AUTO MUSIC Select Button
3. TAPE PROGRAM Button
6. DOLBY Button
1. FF/REW Button
H290A02GK
1FEATURES OF YOUR HYUNDAI 108
H290D02O-GAT 1. FF/REW Button
o Fast forward tape winding starts when the FF ( ) button is pressed during the PLAY or REW mode.
o Tape play starts when the FF ( ) button
is pressed again during the FF mode. o Tape rewinding starts when the REW
( ) button is pressed during the PLAY or FF mode.
o Tape play starts when the REW ( ) button
pressed again during the REW mode.
3. TAPE PROGRAM Button
This allows you to play the reverse side of the tape by merely depressing the program button. An arrow will appear in the display to show tape direction.
4. TAPE EJECT button
o When the button is pressed with the
cassette loaded, the cassette is ejected.
o When the button is pressed during the
FF/REW mode, the cassette is ejected.
2. AUTO MUSIC Select Button
5. EQ Button
Press the button to find the starting point of each song in a prerecorded music tape. The quiet space between songs (must have at least a 4
sec. gap) can be identified by the AUTO MUSIC Select button.o Pressing the button will play the beginn-
ing of the next music segment.
o Pressing the button will start replay at the beginning of the music just listened to.
Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;
CLASSIC → JAZZ → ROCK → DEFEAT
6. DOLBY Button
If you get background noise during tape PLAY, you can reduce this considerably by merely pressing the DOLBY button. If you want to cancel the DOLBY feature, press the button again.
CAUTION:
o Do not insert anything like coins into the player slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
o Do not impact on the audio system, or the playback mechanism could be dam- aged.
H290E01FC-GAT COMPACT DISC PLAYER OPERATION (H280) (If installed)
6. CD EJECT Button
FEATURES OF YOUR HYUNDAI
109
7. SCAN Button (If installed)
5. EQUALIZER Button
3. TRACK UP/DOWN
1. CD Select Button
H290A03GK
4. REPEAT
2. FF/REW Button
1FEATURES OF YOUR HYUNDAI 110
H290F01O-GAT 1. CD Select Button
o Insert the CD with the label facing upward. o Insert the CD to start CD playback, during
radio operation or cassette tape playing.
o When a disc is in the CD deck, if you press the CD button the CD player will begin playing even if the radio or cassette player is being used.
o The CD player can be used when the ignition switch is in either the "ON" or "ACC" position.
2. FF/REW ( / )
If you want to fast forward or reverse through the compact disc track, push and hold the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.
3. TRACK UP/DOWN
o The desired track on the disc currently being played can be selected using the track number.
o Press button once to skip forward to the beginning of the next track. Press button once to skip back to the beginning of the track.
4. REPEAT
7. SCAN Button (If installed)
o To repeat the track you are listening to, press the RPT button. To cancel, press again.
o If you do not release RPT operation when the track ends, it will automatically be replayed. This process will be continued until you push the button again.
5. EQUALIZER Button
Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;
CLASSIC → JAZZ → ROCK → DEFEAT
6. CD EJECT Button
When the button is pressed with a CD loaded, the CD will eject.
o Press the SCAN button to playback the first
10 seconds of each track.
o Press the SCAN button again within 10 sec. When you have reached the desired track.
NOTE: o To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle’s air conditioning or heating system.
o When replacing the fuse, replace it with
a fuse having the correct capacity.
o The preset station frequencies are all erased when the car battery is discon- nected. Therefore, all data will have to be set again if this should occur.
o Do not add any oil to the rotating parts. Keep magnets, screwdrivers and other metallic objects away from the tape mechanism and head.
o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.
o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.
FEATURES OF YOUR HYUNDAI
111
o Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism. These can cause disc scratching to oc- cur or trouble in the compact disc player. o Avoid using CD-Recordable or CD- Rewritable to ensure porper operation. When using the compact disc player, genuine CDs are recommended.
o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.
o Do not expose this equipment (includ- ing the speakers and tape) to water or excessive moisture.
CAUTION:
o Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.
o Do not insert anything like coins into the player slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
o Do not impact on the audio system, or the playback mechanism could be dam- aged.
o Driving off-road or other vibrations may
skip your compact disc. Do not use the audio system off-road as the discs could be scratched and dam- aged.
1FEATURES OF YOUR HYUNDAI 112
H290G01FC-GAT CD AUTO CHANGER (H280) (If Installed)
6. SCAN Button (If installed)
7. EQ Button
3. TRACK UP/DOWN
5. REPEAT
2. DISC Select Button
1. CD CHANGER Select Button
4. FF/REW Button
H290A04GK
3. TRACK UP/DOWN
6. SCAN Button (If installed)
FEATURES OF YOUR HYUNDAI
113
o The desired track on the disc currently being played can be selected using the track number.
o Press once to skip forward to the beginn- ing of the next track. Press once to skip back to the beginning of the track.
4. FF/REW ( / )
If you want to fast forward or reverse through the compact disc track, push and hold in the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.
5. REPEAT
o To repeat the music you are listening to, press the RPT button. To cancel, press again.
o If you do not release RPT operation when the track ends, it will automatically be replayed. This process will be continued until you push the button again.
o Press the SCAN button to playback the first
10 seconds of each track.
o Press the SCAN button again within 10 sec.
for the desired track.
7. EQ Button
Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;
CLASSIC → JAZZ → ROCK → DEFEAT
NOTE: o When replacing the fuse, replace it with
a fuse having the correct capacity.
o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.
o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.
o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.
B290H01GK-GAT The CD auto changer is located in the right side of the quater trim.
o To use the CD auto changer.
1. Open the sliding lid of the CD auto changer. 2. To eject the compact disc magazine, press the EJECT button located inside the CD auto changer. Insert the discs into the magazine.
3. 4. Push the magazine into the CD auto changer
and close the sliding lid.
o The CD auto changer can be used when the ignition switch is in either "ON" or "ACC" position.
1. CD CHANGER Select Button
When the CD changer magazine contains discs, press the "CD/CDC" button and the CD changer can be used even if the radio or cassette player is being used. The Hyundai CD changer can hold up to eight discs. The disc number will be lit, and the track number, and elapsed time will be displayed.
2. DISC Select Button
To select the CD you want, push " " to change the disc number.
TUNE DISC
1FEATURES OF YOUR HYUNDAI 114
CAUTION:
o Do not insert warped or poor quality discs into the changer as damage to the unit may occur.
o Do not insert anything like coins into the changer slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
o Do not impact on the audio system, or the playback mechanism could be dam- aged.
o Driving off-road or other vibrations may
skip your compact disc. Do not use the audio system off-road as the discs could be scratched and dam- aged.
o Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism. These can cause disc scratching to oc- cur or trouble in the compact disc changer.
o Avoid using CD-Recordable or CD- Rewritable to ensure proper operation. When using the compact disc changer, genuine CDs are recommended.
J290A01JM-GAT STEREO RADIO OPERATION (J290) (If installed)
1. POWER ON/OFF/VOLUME Control Knob
2. BAND Select Button
7. TUNE Select Knob / MODE Select Knob
FEATURES OF YOUR HYUNDAI
115
3. SEEK Select Button
6. EQ Button
5. BEST STATION
MEMORY
4. PRESET STATION Select Buttons
J290A01JM
1FEATURES OF YOUR HYUNDAI 116
J290B01JM-GAT 1. POWER ON-OFF/VOLUME
Control Knob
The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the button to switch the power on. The display shows the radio frequency in the radio mode, the tape direction indicator in the tape mode, or CD track in the CD AUTO CHANGER mode. To switch the power off, press the button again.
VOLUME Control
Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.
2. BAND Selector
Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is shown on the display.
3. SEEK Select Button
(Automatic Channel Selection)
Press the SEEK select button 1 sec. or more. When the ( ) side is pressed, the unit will automatically tune to the next higher frequency and when the ( ) side is pressed, it will automatically tune to the next lower frequency.
4. PRESET STATION Select
Buttons
Six (6) stations for AM, FM and FM2 respec- tively can be preset in the electronic memory circuit.
HOW TO PRESET STATIONS
Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the AM / FM select button and/ or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps: o Press AM/FM selector to set the band for
AM, FM1 and FM2.
o Select the desired station to be stored by
seek, scan or manual tuning.
o Determine the preset station select button
you wish to use to access that station.
o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM station per button.
o When completed, any preset station may be recalled by selecting AM, FM1 or FM2 band and the appropriate station button.
5. Best Station Memory Button
(BSM)
When the BSM button is pressed for two sec- onds or longer, the six channels from the high- est field intensity are selected next and stored in memory. The stations selected are stored in the sequence frequency from the first preset key.
6. EQ Button
Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;
CLASSIC → JAZZ → ROCK → DEFEAT
7. TUNE (Manual) Select Knob
Rotate the knob clockwise to increase the frequency and turn the knob counterclockwise to reduce the frequency.
Mode Select Knob
FAD (Fader Control)
Pressing the MODE button changes the BASS, MIDDLE, TREBLE, FADER and BALANCE mode. The mode selected is shown on the display. After selecting the each mode, rotate the mode select knob clockwise or counterclockwise.
Rotate the control knob clockwise to empha- size rear speaker sound (front speaker sound will be attenuated). When the control knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).
FEATURES OF YOUR HYUNDAI
117
BASS Control
To increase the BASS, rotate the knob clock- wise, while to decrease the BASS, rotate the knob counterclockwise.
MID Control
To increase the MID, rotate the knob clockwise, while to decrease the MID, rotate the knob counterclockwise.
TREBLE Control
To increase the TREBLE, rotate the knob clock- wise, while to decrease the TREBLE, rotate the knob counterclockwise.
BALANCE Control
Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclockwise, left speaker sound will be emphasized (right speaker sound will be at- tenuated).
CAUTION:
o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.
1FEATURES OF YOUR HYUNDAI 118
J290C01JM-GAT CASSETTE TAPE PLAYER OPERATION (J290) (If installed)
1.TAPE PROGRAM Button
2.EJECT Button
6.FF/REW Button
5.AUTO MUSIC Select Button
4.REPEAT Button
3. DOLBY Button
J290C01JM
FEATURES OF YOUR HYUNDAI
119
CAUTION:
o Do not insert anything like coins into the player slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
o Do not impact on the audio system, or the playback mechanism could be dam- aged.
J290D01JM-GAT 1. TAPE PROGRAM Button
This allows you to play the reverse side of the tape by merely pressing the program button. The PLAY and an arrow will appear in the display to show tape direction.
5. AUTO MUSIC Select Button
Press the button to find the starting point of each song in a prerecorded music tape. The quiet space between songs (must have at least a 4
sec. gap) can be identified by the AUTO MUSIC Select button.2. EJECT Button
o When the EJECT button is pressed with a
cassette loaded, the cassette will eject.
o When the EJECT button is pressed during
FF/REW mode, the cassette will eject.
o Pressing the will play the beginning of
the next music segment.
o Pressing the will start replay at the
beginning of the music just listened to.
o To stop FF or REW action, press the button
again.
3. DOLBY Button
6. FF/REW Button
If you get background noise during tape PLAY, you can reduce this considerably by merely pressing the DOLBY button. If you want to cancel the DOLBY feature, press the button again.
4. REPEAT Button
o To repeat the track you are currently listen- ing to, press the RPT button. To cancel, press again.
o If you do not release RPT operation when the track ends, it will automatically be replayed. This process will be continued until you push the button again.
o Fast forward tape winding starts when the FF button is pressed during PLAY or REW mode.
o PLAY starts when the FF ( ) button is
pressed again during FF mode.
o Tape rewinding starts when the REW ( ) button is pressed during PLAY or FF mode. o PLAY starts when the REW button pressed
again during REW mode.
1FEATURES OF YOUR HYUNDAI 120
J290E01JM-GAT COMPACT DISC PLAYER / CD AUTO CHANGER OPERATION (J290) (If installed)
1.LOAD Button
2.Playing CD
3.EJECT Button
4. DISC Select
Button
8.FF/REW Button
7.TRACK UP/DOWN
6.REPEAT Button
5.RANDOM Play Button
10.EQ Button
9.SCAN Button
J290E01JM
FEATURES OF YOUR HYUNDAI
121
2. Playing CD
o Press the 6CDC to start CD playback, during radio operation or cassette tape play- ing.
o When discs are in the CD deck, if you press the 6CDC button the CD player will begin playing even if the radio or cassette player is being used.
o The CD player can be used when the ignition switch is in either the "ON" or "ACC" position.
3. EJECT Button
o When the EJECT button is pressed with
a CD loaded, the CD will eject.
o To eject all of the discs, press this button for
2 seconds or more.
4.DISC Select Button
To select the CD you want, push "DISC " or "DISC " to change the disc number.
2. Load a disc while the is blinking. Insert a disc partway into the slot, label side up. The player will pull the disc in. Once the disc is loaded, the numbers of the vacant disc will blink on the display continu- ously. If the next "DISC NO." is appeared on the display with the both side of the slot illuminated, you can then load another disc. 3. Load the remaining disc by following the same
procedures 1 and 2. When you finished loading 6 discs, the CD player will begin to play the last CD loaded. 4. To load more than one disc but less than six, complete Steps 1 and 2. When you have finished loading discs, press LOAD button to cancel the loading function or wait for 10
seconds. The CD player will begin to play the last CD loaded.As each CD starts to play, the DISC number will appear on the display.
NOTE: The disc player takes up to six discs. Do not try to load more than six.
J290F02JM-GAT 1. LOAD Button
This compact disc playing will accommodate up to six discs.
To insert one disc do the following:
1. Press and release the LOAD Button. 2. Green light on both sides of the slot will be illuminated and the will blink ten times on the display.
3. Load a disc while the is blinking. Insert a disc partway into the slot, label side up. The player will pull the disc in.
NOTE: o The disc can be only inserted while the
light is blinking.
o This CD player is suitable only for 12 cm discs, do not use irregular shaped CDs.
When the disc is inserted, the disc will begin to play automatically.
To insert multiple discs do the followings:
1. Press and hold the LOAD button for two
seconds or more. You will then hear two beeps and the green light on the both sides of the slot will be illuminated.
1FEATURES OF YOUR HYUNDAI 122
5. RANDOM Button
8. FF/REW Button
With random, you can listen to the tracks in random, rather than sequential order, on all of the discs or on one disc. To use random, do the following:
While the disc is playing, if you hold down the FF button continuously, the selected track is ad- vanced. Holding down the REW button continu- ously moves the selected track back.
o Press and release the RDM button to play the tracks on all of the discs or on one disc that are loaded, in random order. RDM will appear in the display. Press RDM to turn if off.
6. REPEAT Button
o To repeat the track you are currently listen- ing to, press the RPT button. To cancel, press again.
o If you do not release RPT operation after all the tracks are played back, the unit will play back again from the first track.
7. TRACK UP/DOWN
9. SCAN Button
o Press the SCAN button to playback the first
10 seconds of each track.
o Press the SCAN button again within 10 sec. when you have reached the desired track.
10. EQ Button
Press the EQ button to select the CLASSIC, JAZZ, ROCK and DEFEAT MODE for the desired tone quality. Each press of the button changes the display as follows;
CLASSIC → JAZZ → ROCK → DEFEAT
o The desired track on the disc currently being played can be selected using the track number.
o Press once to skip forward to the begin-
ning of the next track.
o Press once to skip back to the beginning
of the track.
NOTE: o To assure proper operation of the unit, keep the vehicle interior temperature within a normal range by using the vehicle's air conditioning or heating sys- tem.
o When replacing the fuse, replace it with
a fuse having the correct capacity.
o The preset station frequencies are all erased when the car battery is discon- nected. Therefore, all data will have to be set again if this should occur.
o Do not add any oil to the rotating parts. Keep magnets, screwdrivers and other metallic objects away from the tape mechanism and head.
o This equipment is designed to be used only in a 12 volt DC battery system with negative ground.
o This unit is made of precision parts. Do not attempt to disassemble or adjust any parts.
o When driving your vehicle, be sure to keep the volume of the unit set low enough to allow you to hear sounds coming from the outside.
o Do not expose this equipment (includ- ing the speakers and tape) to water or excessive moisture.
FEATURES OF YOUR HYUNDAI
123
CAUTION:
o Do not insert warped or poor quality discs into the CD player as damage to the unit may occur.
o Do not insert anything like coins into the player slot as damage to the unit may occur.
o Do not place beverages close to the audio system. The playback mechanism may be damaged if you spill them.
o Do not impact on the audio system, or the playback mechanism could be dam- aged.
o Driving off-road or other vibrations may
skip your compact disc. Do not use the audio system off-roads as the discs could be scratched and damaged.
o Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism. These can cause disc scratching to oc- cur or trouble in the compact disc player. o Avoid using CD-Recordable or CD- Rewritable to ensure proper operation. When using the compact disc player, genuine CDs are recommended.
1FEATURES OF YOUR HYUNDAI 124
AUDIO FAULT CODE
B890A01Y-AAT If you see any error indication in the display while using the system in the CD or Tape mode, find the cause in the chart below. If you cannot clear the error indication, take the car to your Hyundai dealer.
INDICATION
CAUSE
SOLUTION
Er2
Er3
Er6
Er8
CD DECK MECHANICAL ERROR
After resetting the audio system, push the eject button.
(EJECT ERROR, LOADING ERROR)
If disc is not ejected, consult your Hyundai dealer.
FOCUS ERROR
DATA READ ERROR
DISC ERROR
TAPE DECK ERROR
TAPE EJECT ERROR
Make sure the disc is not scratched or damaged.
Press the eject button and pull out the disc.
Then insert a normal CD disc.
Check if the disc is inserted correctly in the CD player.
Make sure the disc is not scratched or damaged.
After resetting the audio system, push the eject button.
If tape does not eject, consult your Hyundai dealer.
HHH
TEMPERATURE IS TOO HIGH
Fault code will reset automatically when the temperature returns to normal.
no CD
NO DISC IN MAGAZINE
NO CD MAGAZINE IN THE AUTO CHANGER
Insert disc in magazine or insert CD magazine in the auto changer.
FEATURES OF YOUR HYUNDAI
125
CARE OF DISCS
B850A02F-AAT Proper Handling
CARE OF CASSETTE TAPES
Storage
B860A01A-AAT
When not in use, place your discs in their individual case and store them in a cool place away from the sun, heat, and dust. Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism.
Keep Your Discs Clean
B850A01L Handle your disc as shown. Do not drop the disc. Hold the disc so you will not leave finger- prints on the surface. If the surface is scratched, it may cause the pickup to skip signal tracks. Do not affix tape, paper, or gummed labels on the disc. Do not write on the disc.
Damaged Disc
Do not attempt to play damaged, warped or cracked discs. These could severely damage the playback mechanism.
B850A02L Fingerprints, dust, or soil on the surface of a disc could cause the pickup to skip signal tracks. Wipe the surface clean with a clean soft cloth. If the surface is heavily soiled, dampen a clean soft cloth in a solution of mild neutral detergent to wipe it clean.
B860A01L Proper care of your cassette tapes will extend the tape life and increase your listening enjoy- ment. Always protect your tapes and cassette cases from direct sunlight, severely cold and dusty conditions. When not in use, cassettes should always be stored in the original protec- tive cassette case. When the vehicle is very hot or cold, allow the interior temperature to become more comfortable before listening to your cas- settes.
1FEATURES OF YOUR HYUNDAI 126
o Never leave a cassette inserted in the player when not being played. This could damage the tape player unit and the cassette tape. o We strongly recommend against the use of tapes longer than C-60 (60 minutes total). Tapes such as C-120 or C-180 are very thin and do not perform as well in the automotive environment.
o Store cassettes in a cool, dry place with the open side facing down to prevent dust from setting in the cassette body.
o Avoid repeated fast reverse usage to replay one given tune or tape section. This can cause poor tape winding to occur, and even- tually cause excessive internal drag and poor audio quality in the cassette. If this occurs, it can sometimes be corrected by fast winding the tape from end to end several times. If this does not correct the problem, do not continue to use the tape in your vehicle.
o The playback head, capstan and pinch roll- ers will develop a coating of tape residue that can result in deterioration of sound quality, such as a wavering sound. They should be cleaned monthly using a commercially avail- able head cleaning tape or special solution available from audio specialty shops. Follow the supplier's directions carefully and never oil any part of the tape player unit.
o Always be sure that the tape is tightly wound on its reel before inserting in the player. Rotate a pencil in the drive sprockets to wind up any slack.
Head
HGK062
o Be sure that the cassette label is not loose or peeling off or tape ejection may be difficult. o Never touch or soil the actual audio tape
surfaces.
o Keep all magnetized objects, such as elec- tric motors, speakers or transformers away from your cassette tapes and tape player unit.
Cotton applicator
B860A02L
ANTENNA
B870A01A-AAT Fixed Rod Antenna
FEATURES OF YOUR HYUNDAI
127
CAUTION:
o Be sure to remove the antenna before washing the car in an automatic car wash or it may be damaged.
o When reinstalling your antenna, it is important that it is fully tightened to ensure proper reception.
B860A03L
NOTE: Look at a tape before you insert it. If the tape is loose, tighten it by turning one of the hubs with a pencil or your finger. If the label is peeling off, do not put it in the drive mechanism. Do not leave tapes sitting where they are exposed to hot, warm, or high humidity, such as on top of the dashboard or in the player. If a tape is exposed to excessively hot or cold, let it reach a moderate temperature before putting it in the player.
B870A01A
Your car uses a fixed rod antenna to receive both AM and FM broadcast signals. This antenna is a removable type. To remove the antenna, turn it counterclockwise. To install the antenna, turn it clockwise.
DRIVING YOUR HYUNDAI
Engine Exhaust Can Be Dangerous! ............................ 2-2
Before Starting the Engine ............................................ 2-3
Key Positions ................................................................ 2-4
Starting .......................................................................... 2-5
Operating the Manual Transaxle ................................... 2-6
Automatic Transaxle ..................................................... 2-8
Anti-Lock Brake System (ABS) .................................. 2-12
Good Braking Practices .............................................. 2-12
Electronic Stability Program (ESP) ............................. 2-13
Driving for Economy ................................................... 2-15
Winter Driving ............................................................. 2-16
Trailer or Vehicle Towing ............................................ 2-19
Vehicle Load Limit ....................................................... 2-222 DRIVING YOUR HYUNDAI
WARNING: ENGINE EXHAUST CAN BE DANGEROUS!
C010A01GK-AAT Engine exhaust fumes can be extremely dangerous. If, at any time, you smell exhaust fumes inside the vehicle, open the windows immediately. o Do not inhale exhaust fumes. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that can cause unconsciousness and death by asphyxiation. o Be sure the exhaust system does not leak. The exhaust system should be checked whenever the vehicle is raised to change the oil or for any other purpose. If you hear a change in the sound of the exhaust or if you drive over something that strikes the underneath side of the car, have the exhaust system checked as soon as possible by your Hyundai dealer. o Do not run the engine in an enclosed area. Letting the engine idle in your garage, even with the garage door open, is a hazardous practice. Never run the engine in your garage any longer than it takes to start the engine and back the car out. o Avoid idling the engine for prolonged periods with people inside the car. If it is necessary to idle the engine for a prolonged period with people inside the car, be sure to do so only in an open area with the air intake set at "Fresh" and fan operating at one of the higher speeds so fresh air is drawn into the interior. If you must drive with the tail gate open because you are carrying objects that make this necessary: 1. Close all windows. 2. Open side vents. 3. Set the air intake control at "Fresh", the air flow control at "Floor" or "Face" and the fan at one of the higher speeds. To assure proper operation of the ventilation system, be sure the ventilation air intakes located just in front of the windshield are kept clear of snow, ice, leaves or other obstructions.
PROPOSITION 65 WARNING:
Engine exhaust and a wide variety of automobile components and parts, including components found in the interior furnishings in a vehicle, contain or emit chemicals known to the State of California to cause cancer and birth defects and reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
BEFORE STARTING THE ENGINE
TO START THE ENGINE
DRIVING YOUR HYUNDAI
C020A02A-AAT Before you start the engine, you should always:
1. Look around the vehicle to be sure there are no flat tires, puddles of oil, water or other indications of possible trouble.
2. After entering the car, check to be sure the
parking brake is engaged.
3. Check that all windows, and lights are clean. 4. Check that the interior and exterior mirrors
are clean and in position.
5. Check your seat, seatback and headrest to be sure they are in their proper positions.
6. Close all the doors. 7. Fasten your seat belt and be sure that all
other occupants have fastened theirs.
8. Turn off all lights and accessories that are
not needed.
9. When you turn the ignition switch to "ON", check that all appropriate warning lights are operating and that you have sufficient fuel. 10.Check the operation of warning lights and all
bulbs when key is in the "ON" position.
! WARNING:
o All passengers must be properly belted whenever the vehicle is moving. Refer to pages: 1-16 through 1-20 for more infor- mation on their proper use.
o Always check the surrounding areas near your vehicle for people, especially chil- dren, before putting a car into 'drive.'
WARNING:
Always wear appropriate shoes when oper- ating your vehicle. Unsuitable shoes (high heels, ski boots, etc.) may interfere with your ability to use the brake and accelerator pedal, and the clutch (if installed).
C030A01A-AAT COMBINATION IGNITION SWITCH
o If your Hyundai is equipped with a manual transaxle, place the shift lever in neutral and depress the clutch pedal fully.
o If your Hyundai has an automatic transaxle,
place the shift lever in "P" (park).
o To start the engine, insert the ignition key and turn it to the "START" position. Release it as soon as the engine starts. Do not hold the key in the "START" position for more than 15
seconds.NOTE: o For safety, the engine will not start if the clutch pedal is not depressed fully (Manual transaxle) or the shift lever is not in "P" or "N" Position (Automatic transaxle).
o The ignition key cannot be turned from "ACC" position to "LOCK" position un- less the shift lever is in the "P" (Park) position or the negative battery terminal is disconnected from the battery. To remove the key, always confirm that the shift lever is securely positioned in "P" (Park) (For Automatic transaxle)
o For additional information about start-
ing, see page 2-5.
2 DRIVING YOUR HYUNDAI KEY POSITIONS
C040A02A-AAT
ACC
LOCK
ON
START
C040A01E-1
WARNING:
The engine should not be turned off or the key removed from the ignition key cylinder while the vehicle is in motion. The steering wheel is locked by removing the key.
o "START"
The engine is started in this position. It will crank until you release the key.
C070C03A-AAT To Remove the Ignition Key
ACC
LOCK
ON
START
C070C01E-1
1. Turn the ignition key counterclockwise from the "ACC" position to the "LOCK" position. 2. The key can be removed in the "LOCK"position.
NOTE: Do not hold the key in the "START" position
for more than 15 seconds.
o "ON"
When the key is in the "ON" position, the ignition is on and all accessories may be turned on. If the engine is not running, the key should not be left in the "ON" position. This will discharge the battery and may also damage the ignition sys- tem.
o "ACC"
With the key in the "ACC" position, some elec- trical accessories (radio, etc.) may be oper- ated.
o "LOCK"
The key can be removed or inserted in this position. To protect against theft, the steering wheel locks by removing the key.
NOTE: If difficulty is experienced in turning the ignition key to the START position, turn the steering wheel right and left to release the tension and then turn the key.
DRIVING YOUR HYUNDAI
! WARNING:
Always fully depress the brake pedal before
