2006 Hyundai Tiburon Owners Manual

trolled driver information gauge that displays information related to driving, such as estimated distance to empty, average speed and drive time on the LCD.

Reset Switch

o The reset switch is used to zero the multi-

functional display mode.

o Pushing in the reset switch on the left side of tacometer changes the display as follows;

DISTANCE TO EMPTY

AVERAGE SPEED

DRIVE TIME

1. Distance to Empty

Type A

Type B

HGK2063

NOTE: o When the distance to empty is less than 50 km, the symbol will always come on and the distance to empty digits will indicate "---" with flash until more fuel is added.

o The distance to empty can differ from the actual tripmeter according to driving conditions.

o The distance to empty can vary accord- ing to the driving conditions, driving pattern or vehicle speed.

o This mode provides the estimated distance to empty from the current fuel level in the fuel tank.

o The trip computer may not register additional fuel if less than 6 liters of fuel are added to the vehicle.

o When the battery has been reinstalled after being discharged or disconnected, drive more than 32km for an accurate distance to empty.

FEATURES OF YOUR HYUNDAI

45

2. AVERAGE SPEED

Type A

Type B

B400B02GK-E

o This mode indicates the average speed travelled since the last average speed reset. o To reset the average speed to zero, press and hold the reset switch for more than 1
second while the average speed is being displayed.

1FEATURES OF YOUR HYUNDAI 46

3. DRIVE TIME

Type A

Type B

HGK2065

o This mode indicates the drive time travelled

since the last drive time reset.

o To reset the drive time to zero, press and hold the reset switch for more than 1 second while the drive time is being displayed.

MULTI GAUGE

B330C01GK-GAT (If installed)

Multi gauge is consists of torque gauge, instan- taneous fuel consumption gauge and volt gauge.

B330C04GK

Instantaneous fuel Consumption gauge

It shows instantaneous fuel consumption ac- cording to the driving condition. The more indi- cated figure is low, the more it indicates efficient driving situation.

B330C01GK

Torque gauge

It shows instantaneous change of the torque by rpm.

MULTI-FUNCTION LIGHT SWITCH

B340A01A-AAT COMBINATION TURN SIGNAL, HEADLIGHT AND HIGH-BEAM SWITCH Turn Signal Operation

Pulling down on the lever causes the turn signals on the left side of the car to blink. Pushing upwards on the lever causes the turn signals on the right side of the car to blink. As the turn is completed, the lever will automatically return to the center position and turn off the turn signals at the same time. If either turn signal indicator light blinks more rapidly than usual, goes on but does not blink, or does not go on at all, there is a malfunction in the system. Check for a burned- out fuse or bulb or see your Hyundai dealer.

FEATURES OF YOUR HYUNDAI

47

B340B01A-AAT Lane Change Signal

HGK2079

To indicate a lane change, move the lever up or down to a point where it begins flashing. The lever will automatically return to the center position when released.

B330C03GK

Volt gauge

It shows moment volt change and makes for diver correspond to low volt situation.

1FEATURES OF YOUR HYUNDAI 48

B340C04E-AAT Headlight Switch

HGK2074

To operate the headlights, turn the barrel on the end of the multi-function switch. The first posi- tion turns on the parking lights, sidelights, tail lights and instrument panel lights. The second position turns on the headlights.

NOTE: The ignition must be in the "ON" position to turn on the headlight.

Parking light auto cut

o The purpose of this feature is to prevent the battery from being discharged. The system automatically turns off the small light when the driver removes the ignition key and opens the driver- side door.

o With this feature, the parklight will be turned off automatically if the driver parks on the side of road at night.

If necessary, to keep the lights on when the ignition key is removed, perform the following : 1) Open the driver-side door. 2) Turn the parklights OFF and ON again using

the light switch on the steering column.

B340D01A-AAT High-beam Switch

To turn on the headlight high beams, push the lever forward (away from you). The high beam indicator light will come on at the same time. For low beams, pull the lever back toward you.

B340G01LZ-GAT Auto Light (If installed)

HGK2075
To operate the automatic light feature, turn the barrel on the end of the multi-function switch. If you set the multi-function switch to "AUTO", the tail lights and headlights will be turned automati- cally on or off according to external illumination.

NOTE: Switch on car light manually in foggy, cloudy and rainy conditions.

B340E01A-AAT Headlight Flasher

FEATURES OF YOUR HYUNDAI

WINDSHIELD WIPER AND WASHER SWITCH

B350A01A-AAT

49

HGK2077

To flash the headlights, pull the switch lever toward you, then release it. The headlights can be flashed even though the headlight switch is in the "OFF" position.

The windshield wiper switch has three posi- tions:

HGK042A

(1) Intermittent wiper operation (2) Low-speed operation (3) High-speed operation

NOTE: To prevent damage to the wiper system, do not attempt to wipe away heavy accumula- tions of snow or ice. Accumulated snow and ice should be removed manually. If there is only a light layer of snow or ice, operate the heater in the defrost mode to melt the snow or ice before using the wiper.

Auto Light Sensor

B340G01GK

NOTE: o Never place anything over sensor lo- cated on the instrument panel, this will ensure better auto light system control. o Don't clean the sensor using a window

cleaner.

o If your vehicle has window tint or other types of coating on the front windshield, the AUTO light system may not work properly.

1FEATURES OF YOUR HYUNDAI 50

B350B01O-AAT Windshield Washer Operation

Mist Wiper Operation

B350C01S-AAT Adjustable Intermittent Wiper Operation

HGK044A To use the windshield washer, pull the wiper/ washer lever toward the steering wheel. When the washer lever is operated, the wipers auto- matically make two passes across the wind- shield. The washer continues to operate until the lever is released.

HGK045A If a single wipe is desired in mist, move the windshield wiper and washer control lever up.

HGK043A

To use the intermittent wiper feature, place the wiper switch in the "INT" position. With the switch in this position, the interval between wipes can be varied from 2 to 10 seconds by turning the interval adjuster barrel.

NOTE: o Do not operate the washer more than 15
seconds at a time or when the fluid reservoir is empty.

o In icy or freezing weather, be sure the wiper blades are not frozen to the glass prior to operating the wipers.

o In areas where water freezes in winter,

use windshield washer antifreeze.

B390A01E-AAT Rear Window Wiper And Washer Switch

Do not operate the washer continuously for more than 15 seconds or when the fluid reser- voir is empty; this could damage the system. Do not operate the wiper when the window is dry; this can result in scratching as well as prema- ture wiper blade wear. For the reason stated above,do not operate the washer when the washer fluid reservoir is empty.

1.

5.

HGK046A : The rear window wiper starts to oper- ate three times after the washer fluid sprays onto the rear window.

2.OFF 3.INT : The interval between wipes operates

every 5 seconds intermittently.

4.ON : The rear window wiper starts to oper-

ate continuously.

: The washer fluid will be sprayed onto the rear window and the wiper operates while the rear window wiper barrel is placed in this position.

FEATURES OF YOUR HYUNDAI

FRONT FOG LIGHT SWITCH

51

B360A04A-AAT

B360B01GK-A To turn on the front fog lights, push the switch. They will light when the headlight switch is in the second position and the ignition key is in the "ON" position.

NOTE: If you turn on the headlight high beams, the front fog lights will be turned off.

1FEATURES OF YOUR HYUNDAI 52

HAZARD WARNING SYSTEM

B370A01A-AAT

Type A

Type B

Type C

B370A01GK The hazard warning system should be used whenever you find it necessary to stop the car in a hazardous location. When you must make such an emergency stop, always pull off the road as far as possible. The hazard warning lights are turned on by pushing in the hazard switch. This causes all turn signal lights to blink. The hazard warning lights will operate even though the key is not in the ignition. To turn the hazard warning lights off, push the switch a second time.

NOTE: The ignition must be running for the rear window defroster to operate.

REAR WINDOW DEFROSTER SWITCH

B380A02A-AAT

Type A

Type B

HGK2090-1

The rear window defroster and heated outside rearview mirrors are turned on by pushing in the switch. To turn the defroster off, push the switch a second time. The rear window defroster automatically turns itself off after about 15 min- utes. To restart the defroster cycle, push in the switch again after it has turned itself off.

CAUTION:

Do not clean the inner side of the rear window glass with an abrasive type of glass cleaner or use a scraper to remove foreign deposits from the inner surface of the glass as this may cause damage to the defroster elements.

DIGITAL CLOCK

INSTRUMENT PANEL LIGHT CONTROL (RHEOSTAT)

CIGARETTE LIGHTER

B400A01A-AAT

B410A01A-AAT

B420A02A-AAT

FEATURES OF YOUR HYUNDAI

53

HGK143A

HGK2150

The instrument panel lights can be made brighter or dimmer by turning the instrument panel light control knob.

There are three control buttons for the digital clock. Their functions are:

HOUR - Push "H" to advance the hour indi-

cated.

cated.

MIN

- Push "M" to advance the minute indi-

RESET - Push "R" to reset minutes to ":00" to facilitate resetting the clock to the correct time. When this is done:

Pressing "R" between 10 : 30 and 11 : 29
changes the readout to 11 : 00. Pressing "R" between 11 : 30 and 12 : 29
changes the readout to 12 : 00.

HGK2118
For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position. To use the cigarette lighter, push it all the way into its socket. When the element has heated, the lighter will pop out to the "ready" position. Do not hold the cigarette lighter pressed in. This can damage the heating element and create a fire hazard. If it is necessary to replace the cigarette lighter, use only a genuine Hyundai replacement or its approved equivalent.

CAUTION:

Do not use electric accessories or equip- ment other than the Hyundai genuine parts in the socket.

1FEATURES OF YOUR HYUNDAI 54

ASHTRAY

B430A01GK-AAT

DRINK HOLDER

B450A02GK-AAT (If Installed)

Driver's

Passenger's

HGK2120
The front ashtray may be opened by pushing and releasing the ashtray door at its top edge. To remove the ashtray in order to clean it, the metal ash receptacle should be lifted out from the ashtray door. Do not attempt to remove the entire ashtray door assembly or damage will result. To reinstall it, place it in the proper position and press it down in the ashtray door. The ashtray lamp will only illuminate when the exterior body lights are switched on.

HGK2123
The drink holder is used for holding cups or cans. To use the passenger's drink holder, push the drink holder.

WARNING:

o Use caution when using the drink hold- ers. A spilled beverage that is very hot can injure you or your passengers. Spilled liquids can damage interior trim and electrical components.

o Do not place objects other than cups or cans in the drink holder. Such objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.

SUNSHADE

B470A01S-AAT (If Installed)

SUNROOF

B460A01S-AAT (If Installed)

The sunroof can be operated with the ignition key in the "ON" position.

B460B03GK-GAT Opening the Sunroof System

HGK2026
The sunshade can be opened and closed by sliding it forward or rearward when the sunroof is closed. The sunshade will open automatically when the sunroof is opened, but it must be closed manually.

WARNING:

Never adjust the sunshade while driving.

HGK2022
The sunroof can be electrically opened or closed with the ignition key in the "ON" position. The sunroof is moved to its fully open position by pushing the " " switch, and to stop at the desired position, push in any switches ( , , Up, Down). To close, press and hold the " " button. Release the button when the sunroof reaches the desired position.

FEATURES OF YOUR HYUNDAI

55

WARNING:

o Do not close a sunroof if anyone’s hands, arms or body are between the sliding glass and the sunroof sash, as this could result in injury.

o Do not place your head or arms out of the

sunroof opening at any time.

o While the vehicle is moving, always keep the head, hands and other parts of the body of all occupants away from the roof opening. Otherwise, you could be seri- ously injured if the vehicle stops sud- denly or if the vehicle is involved in an accident.

CAUTION:

o Do not open the sunroof in severely cold temperature or when it is covered with ice or snow.

o Periodically remove any dirt that may

have accumulated on the guide rails.

1FEATURES OF YOUR HYUNDAI 56

B460C01S-AAT Tilting the Sunroof System

B460D03GK-AAT Manual Operation of Sunroof

If the sunroof does not electrically operate:

HGK2023
The sunroof can be tilted by pushing the "UP" button with the sunroof closed. Release the button when the sunroof reaches the desired position. To close the sunroof, press the "DOWN" button.

NOTE: After washing the car or after there is rain, be sure to wipe off any water that is on the sunroof before operating it.

HGK2024
1. Remove the cap located in the rear roof

panel by using a coin or screw driver.

HGK2025

2.

Insert the hexagonal head wrench provided with the vehicle into the socket. This wrench can be found in the vehicle’s trunk or glove box.

3. Push and turn the wrench clockwise to close or counterclockwise to open the sunroof.

INTERIOR LIGHT

SUNGLASS HOLDER

FEATURES OF YOUR HYUNDAI

57

B460E03GK-GAT Resetting the Sunroof System

B480A01GK-GAT MAP LIGHT

B491A02F-AAT

If the battery has been recharged, discon- nected or is manually with operating the hex- agonal head wrench, you may need to reset the sunroof.

To do this; 1. Turn the ignition switch "OFF". 2. With pressing " " "up" button at the same

time, turn the ignition switch "ON".

The resetting is failed when the ignition key to the "OFF" within 1.5 seconds.

3.

If the sunroof is set like this, the sunroof is reset with tilting up/down automatically once for all.

CAUTION:

If the sunroof is not reset, it may not operate normally.

(1)

(2)

(3)

HGK2087

(1) Push in the map light switch to turn on the

driver side light.

(2) In the "DOOR" position, the interior cour- tesy light comes on when any door is opened regardless of the ignition key posi- tion. The light goes out gradually 6 seconds after the door is closed.

(3) Push in the map light switch to turn on the

driver side light.

HGK2122

The sunglass holder is located on the front overhead console. Push the end of the cover to open or close the sunglass holder.

WARNING:

o Do not keep objects except sunglass inside the sunglass holder. Such ob- jects can be thrown from the holder in the event of a sudden stop or an acci- dent, possibly injuring the passengers in the vehicle.

o Do not open the sunglass holder while the vehicle is moving. The rear view mirror of the vehicle can be blocked by an open sunglass holder.

1FEATURES OF YOUR HYUNDAI 58

GLOVE BOX

B500A01A-AAT

MIRROR

B510B01A-AAT OUTSIDE REAR VIEW MIRROR Electric Type

2. Next, adjust the mirror angle by depressing the appropriate perimeter switch as illus- trated.

CAUTION:

o Do not operate the switch continuously

for an unnecessary length of time.

o Scraping ice from the mirror face could cause permanent damage. To remove any ice, use a sponge, soft cloth or approved deicer.

WARNING:

Be careful when judging the size or dis- tance of any object seen in the passenger side rear view mirror. It is a convex mirror with a curved surface. Any objects seen in this mirror are closer than they appear.

HGK2121

WARNING:

To avoid the possibility of injury in case of an accident or a sudden stop, the glove box door should be kept closed when the car is in motion.

o To open the glove box, pull on the glove box

release lever.

HGK2053
The outside rearview mirrors can be adjusted to your preferred rear vision, both directly be- hind the vehicle, and to the rear of the left and right sides. The remote control outside rearview mirror switch controls the adjustments for both the right and left outside mirror.

To adjust the position of either mirror:

1. Move the selecting switch to the right or left to activate the adjustable mechanism for the corresponding door mirror.

B510D01Y-AAT OUTSIDE REARVIEW MIRROR HEATER (If Installed)

B510C01A-AAT FOLDING THE OUTSIDE REAR VIEW MIRRORS

B520A01A-AAT

FEATURES OF YOUR HYUNDAI

DAY/NIGHT INSIDE REAR VIEW MIRROR

59

Type A

Type B

HGK2090-1

HGK2055

The outside rearview mirror heater is actuated in connection with the rear window defroster. To heat the outside rearview mirror glass, push in the switch for the rear window defroster. The rearview mirror glass will be heated for defrost- ing or defogging and will give you improved rear vision in inclement weather conditions. Push the switch again to turn the heater off. The outside rearview mirror heater automatically turns itself off after 15 minutes.

To fold the outside rear view mirrors, push them toward the rear. The outside rear view mirrors can be folded rearward for parking in narrow areas.

WARNING:

Do not adjust or fold the outside rear view mirrors while the vehicle is moving. This could result in loss of control, and an acci- dent which could cause death, serious in- jury or death.

HGK2052

Your Hyundai is equipped with a day/night inside rear view mirror. The "night" position is selected by flipping the tab at the bottom of the mirror toward you. In the "night" position, the glare of headlights of cars behind you is reduced.

1FEATURES OF YOUR HYUNDAI 60

PARKING BRAKE

B520B02O-GAT (Electric type) (If installed)

B530A03A-EAT

HLZ2068-1
The electric type day/night inside rearview mir- ror automatically controls the glare of headlights of the car behind you.

1. Pressing the button turns the auto- dimming function OFF which is indicated by the green Status Indicator LED turning off. 2. Pressing the button again turns the auto- dimming function ON which is indicated by the green Status Indicator LED turning on.

NOTE: The mirror defaults to the "ON" position each time the vehicle is started.

HGK3019
The parking brake must always be set when the vehicle is to be left unattended. When the parking brake is applied, and the ignition key is at the "ON" position, the parking brake warning lamp will be illuminated. Before driving the vehicle, the parking brake must be fully released and the warning lamp extinguished.

o To engage the parking brake, first apply the foot brake and then without pressing the release button in, pull the parking brake lever up as far as possible. In addition it is recommended that when parking the vehicle on a gradient, the shift lever should be positioned in the appropriate low gear on manual transmission vehicles or in the Park position on automatic transmis- sion vehicles.

o To release the parking brake, first apply the foot brake and pull up the parking brake lever slightly. Secondly, depress the release but- ton and lower the parking brake lever whilst holding the button.

! WARNING:

Whenever leaving vehicle or parking always set the parking brake as far as possible and fully engage the vehicle's transaxle into the park position. Vehicles not fully engaged in park with the parking brake set are at risk for moving inadvertently and injuring yourself or others.

HIGH-MOUNTED REAR STOP LIGHT

B550A01S-GAT

Type A

Type B

Type C

FRONT DOOR EDGE WARNING LIGHT B620A01S-AAT

HOOD RELEASE

B570A01GK-GAT

FEATURES OF YOUR HYUNDAI

61

B550A02GK

In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rear stoplight in the center of the rear window or inserted in the rear spoiler also lights when the brakes are applied.

B620A01GK

Hood Release Lever

HGK2019

A red light comes on when the front door is opened. The purpose of this light is to assist when you get in or out and also to warn passing vehicles.

1. Pull the release knob to unlatch the hood.

HGK2020
2. Press the safety hook lever up and lift the

hood.

3. Raise the hood by hand.

1FEATURES OF YOUR HYUNDAI 62

REMOTE FUEL-FILLER LID RELEASE

When closing the hood, slowly close the hood and make sure it locks into place.

B560A03JM-AAT

WARNING:

o Always double check to be sure that the hood is firmly latched before driving away. If it is not latched, the hood could open while the vehicle is being driven, causing a total loss of visibility, which might result in an accident.

o Do not move the vehicle with the hood in the raised position, as vision is ob- structed and the hood could fall or be damaged.

HGK2017

The fuel-filler lid may be opened from inside the vehicle by pulling up on the fuel-filler lid opener located on the front floor area on the left side of the vehicle.

HGK2018Q

NOTE: If the fuel-filler lid will not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved deicer fluid (do not use radiator anti-freeze) or move the ve- hicle to a warm place and allow the ice to melt.

!

WARNING:

o Gasoline vapors are dangerous. Before refueling, always stop the engine and never smoke or allow sparks and open flames near the filler area.

o Never operate your vehicle without a filler cap properly installed, flammable vapors and gasoline could leak out in dangerous situations such as a collision or rollover. If the filler cap must be replaced, only use genuine Hyundai re- placement parts.

o After refueling, make sure the fuel cap is installed securely to prevent fuel spill- age in the event of an accident

o Tighten the cap until it clicks, otherwise

the "

" light will illuminate

o If you open the fuel filler cap during high ambient temperatures, a slight "pres- sure sound" may be heard. This is nor- mal and not a cause for concern. Whenever you open the fuel filler cap, turn it slowly.

o Do not "top off" after the nozzle auto-

matically shuts off when refueling.

o Automotive fuels are flammable/explo- sive materials. When refueling, please note the following guidelines carefully.

TAIL GATE

FEATURES OF YOUR HYUNDAI

63

B540A01F-AAT Remote Tail Gate Release

HGK2012
To open the tail gate without using the key, pull up the lid release lever located on the driver's door panel. To close, lower the tail gate, then press down on it until it locks. To be sure the tail gate is securely fastened, always try to pull it up again.

- Before touching the fuel nozzle or fuel filler cap, have one's hands in contact with metal parts away from the filler neck to discharge static electricity.

- Do not get back in the vehicle while refueling. Do not operate anything that can produce static electricity. Static electricity discharge can ignite fuel vapors resulting in an explosion.

- When using a portable fuel container, be sure to place the container on the ground while refueling. Static electric- ity discharge from the container can ignite fuel vapors causing a fire. While starting refueling, contact should be maintained until the filling is complete. - Do not use cellular phones around a gas station. The electric current or elec- tronic interference from cellular phones can ignite fuel vapors causing a fire. - When refueling, always turn the engine off. Sparks by engine compartment electrical equipment can ignite fuel vapors causing a fire. After refueling, check to make sure the fuel filler cap is securely closed, and then start the engine.

- Do not smoke or try to light cigarettes around a gas station. Automotive fuels are flammable.

1FEATURES OF YOUR HYUNDAI 64

WARNING:

The tail gate should always be kept com- pletely closed while the vehicle is in motion. If it is left open or ajar, poisonous exhaust gases may enter the car resulting in serious illness or death to the occupants. See addi- tional warnings concerning exhaust gases on page 2-2.

B540C01F-AAT To Unlock Using the Key

B540D01GK-GAT when you close the tailgate

HGK2011
To open the tail gate, insert the key and turn it clockwise to unlock. The tail gate compartment light illuminates when the tail gate is opened.

HGK1034

HGK227

!

WARNING:

Do not close an open tailgate (rear hatch) while a person(s) is sitting upright on the rear seat. The tailgate or tailgate glass may contact the head of a person sitting upright on the rear seat. Closing the tailgate onto a person's head may cause serious injuries, including death.

SUN VISOR

B580A02A-AAT

Vanity mirror

HGK2119
Your Hyundai is equipped with sun visors to give the driver and front passenger either frontal or sideward shade. To reduce glare or to shut out direct rays of the sun, turn the sun visor down. A vanity mirror is provided on the back of the sun visor for the front passenger. NOTE: The Supplemental Restraint System (SRS) label containing useful information can be found on the front of each sun visor.

WARNING:

Do not place the sun visor in such a manner that it obscures visibility of the roadway, traffic or other objects.

FEATURES OF YOUR HYUNDAI

STEERING WHEEL TILT LEVER

65

B600A01HP-AAT (If installed)

HGK2049

To adjust the steering wheel: 1. Pull the lever toward you and hold it to unlock. 2. Raise or lower the steering wheel to the

desired position.

3. After adjustment, release the lever.

WARNING:

Do not attempt to adjust the steering wheel while driving as this may result in loss of control of the vehicle and serious injury or death.

1FEATURES OF YOUR HYUNDAI 66

HORN

B610A01S-GAT

LUGGAGE NET

Working Zone

B540D02HP-GAT (if installed) Type A

WARNING:

Avoid eye injury. Do not overstretch. Al- ways keep face and body out of recoil path. Do not use when strap has visible signs of wear or damage.

Type B

Press the pad on the steering wheel to sound the horn.

HGK2050

HGK2126
Some objects can be kept in the net in the luggage compartment. Use the luggage net on the floor(If installed) or at the back of the luggage compartment to prevent objects from sliding.

B990A03Y-AAT Floor Mat Anchor

CAUTION:

To prevent damage to the goods or the vehicle, care should be taken when carrying fragile or bulky objects in the luggage com- partment.

HGK129

When using a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor in your vehicle. This keeps the floor mat from sliding forward.

!

WARNING:

o Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and interferes with the movement of the pedals during driving, it may cause an accident.

o Don't put an additional floor mat on the top of the anchored mat, otherwise the additional mat may slide forward and interfere with the movement of the ped- als.

CRUISE CONTROL

B660A02S-AAT (If Installed)

FEATURES OF YOUR HYUNDAI

67

B660B01GK-AAT To Set the Cruise Speed

B660A01GK The cruise control system provides automatic speed control for your comfort when driving on freeways, tollroads, or other noncongested highways. This system is designed to function above approximately 25 mph (40 km/h).

NOTE: Cruise control is not recommended for city driving, winding roads, slippery roads, heavy rain, or other bad weather condi- tions.

B660B01GK 1. Push in the cruise control main switch on the end of the barrel. The "CRUISE" indicator light in the instrument cluster will be illumi- nated. This turns the system on.

2. Accelerate to the desired cruising speed

above 25 mph (40 km/h).

3. Push the control switch downward to "SET

(COAST)" and release it. The "SET" indicator light in the instrument cluster will illuminate.

4. Remove your foot from the accelerator pedal and the desired speed will automatically be maintained.

1FEATURES OF YOUR HYUNDAI 68

5. To momently increase speed, depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you remove your foot from the accelerator pedal, the vehicle will return to the speed you have set.

B660C01GK-AAT To Cancel the Cruise Speed

B660D01E-AAT To Resume the Preset Speed

WARNING:

To avoid accidental cruise control engage- ment, keep the cruise control main switch off when not using the cruise control.

B660C01GK To disengage the cruise control system, pull the control switch toward the steering wheel to "CANCEL" position. Additionally, the following actions will disengage the system :

B660D01GK The vehicle will automatically resume the speed set prior to cancellation when you push the control switch upward to "RESUME (ACCEL)" position and release it, providing the vehicle speed is above 25 mph (40 km/h).

o Depress the brake pedal. o Depress the clutch pedal (Manual transaxle). o Shift the selector lever to "N" position (Auto-

matic transaxle).

o Decrease the vehicle speed lower than the

memorized speed by 9 mph (15 km/h).

o Decrease the vehicle speed to less than 25

mph (40 km/h).

o Release the main switch.

FEATURES OF YOUR HYUNDAI

69

WARNING:

o During normal cruise control operation, when the "SET(COAST)" is activated or reactivated after applying the brakes, the cruise control will energize after approximately 3 seconds. This delay is normal.

B660E01E-AAT To Reset at a Faster Speed

1. Push the control switch upward to "RE-

SUME (ACCEL)" position and hold it.

2. Accelerate to desired speed and release the control switch. While the control switch is held, the vehicle will gradually gain speed.

B660F03E-AAT To Reset at a Slower Speed

B660B01GK

1. Push the control switch downward to "SET (COAST)" and hold it. The vehicle will decel- erate.

2. When the desired speed is obtained, release the control switch. While the control switch is pushed, the vehicle speed will gradually decrease.

WARNING:

o Keep the cruise control ON/OFF switch off when not using the cruise control to avoid inadvertently setting a speed.

o Use the cruise control system only when traveling on open highways in good weather.

o Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slippery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.

o Pay particular attention to the driving conditions whenever using the cruise control system.

o During cruise-control driving with a manual transaxle vehicle, do not shift into neutral without depressing the clutch pedal, or the engine will be overrevved. If this happens, depress the clutch pedal or release the main switch. o With the cruise control engaged, when the brake pedal is applied, it is normal to hear the cruise control system deacti- vate. This is an indication of normal system operation.

1FEATURES OF YOUR HYUNDAI 70

AUDIO REMOTE CONTROL SWITCH B610A01GK-GAT (If installed)

SEEK (UP / ) Switch

Press the SEEK UP ( ) switch 1 sec. or more.

1. RADIO mode

When the SEEK UP ( ) switch is pressed, the unit will automatically tune to the next higher frequency.

2. TAPE mode

Pressing the SEEK UP ( ) switch will play the beginning of the next music segment.

B610A01GK

3. CD (compact disc)/CDC

The steering wheel audio remote control switch is installed to promote safe driving.

POWER ON/OFF Switch

Press the POWER ON/OFF switch to select Radio, Tape, CD (compact disc) and CDC (compact disc changer).

Press the POWER ON/OFF switch once again to cancel Radio, Tape, CD (compact disc) and CDC (compact disc changer).

(compact disc changer) mode

Press the SEEK UP ( ) switch once to skip forward to the beginning of the next track.

VOL ( / ) Switch

o Press the VOL ( ) button to increase

o Press the VOL ( ) button to decease

volume.

volume.

HEATING AND COOLING CONTROL

B710A02GK-GAT

1. Side Defrost Nozzle 2. Side Ventilator 3. Windshield Defrost Nozzle 4. Center Ventilator

HGK0003-1

FEATURES OF YOUR HYUNDAI

71

B710B02O-AAT CENTER VENTILATOR

The center ventilators are located in the middle of the dashboard. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.

B710C01JM-AAT SIDE VENTILATOR

The side ventilators are located on each side of the dash board. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.

1FEATURES OF YOUR HYUNDAI 72

HEATING AND VENTILATION

B670A01GK-GAT Rotary Type

B670B02A-AAT Fan Speed Control (Blower Control)

B670E02A-AAT Temperature Control

HGK002-3

1. Air Conditioning switch 2. Air intake control switch 3. Rear window defroster switch 4. Air flow control switch 5. Fan speed control switch 6. Temperature control switch

HGK2093
This is used to turn the blower fan on or off and to select the fan speed. This blower fan speed, and therefore the vol- ume of air delivered from the system, may be controlled manually by setting the blower con- trol between the "1" and "4" positions. The "0" position turns the blower fan off.

NOTE: If the blower fan is off, the air intake control is set to the fresh mode automatically.

Cool

Warm

HGK2092

This control is used to adjust the degree of heating or cooling desired.

B670C02GK-AAT Air Intake Control

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function selected.

B670D04GK-AAT Air Flow Control

FEATURES OF YOUR HYUNDAI

73

With the "Recirculation" mode selected, air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: It should be noted that prolonged opera- tion of the heating system in "Recircula- tion" mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Recircula- tion" mode selected may result in the air within the passenger compartment becom- ing excessively dry.

HGK005-1
This is used to direct the flow of air. Air can be directed to the floor, instrument panel outlets, or windshield. Five symbols are used to represent Face, Bi-Level, Floor, Floor-Defrost and De- frost air position. The MAX A/C mode is used to cool the inside of the vehicle faster.

HGK2100
This is used to select fresh outside air or recirculating inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FRESH MODE ( ) : The indicator light on the button goes off when the air intake control is fresh mode.

RECIRCULATION MODE ( ): The indicator light on the button is illuminated when the air intake control is recirculation mode.

1FEATURES OF YOUR HYUNDAI 74

HGK2095

HGK2096

HGK2097

Face-Level

Bi-Level

Selecting the "Face" mode will cause air to be discharged through the side and center venti- lators.

Air is discharged through the dash vents and the floor vents.

Floor-Level

Air is discharged through the floor vents, wind- shield defroster nozzle, side defroster nozzle, side ventilator. If the "Floor" mode is selected, the "Fresh" mode will be activated.

FEATURES OF YOUR HYUNDAI

75

mode except the defrost mode and the floor-defrost mode. Although the A/C switch indicator is turned off, this is normal operation.

Floor-Defrost Level

Defrost-Level

HGK2098

HGK2099

Air is discharged through the windshield defrost nozzle, the floor vents, side defroster nozzle, side ventilator. If the "Floor-Defrost" mode is selected, the A/C will be turn on automatically and "Fresh" mode will be activated.

Air is discharged through the windshield defrost nozzle, side defroster nozzle, side ventilator. If the "Defrost" mode is selected, the A/C will turn on automatically and "Fresh" mode will be activated.

NOTE: If the "Floor-Defrost" or "Defrost" mode is selected, the air conditioning will not turn off by pushing the A/C button. If the air flow control is set to the defrost or the floor-defrost mode, the A/C will be on automatically and the A/C will not off until the air flow control is set to the another

HGK021-1

MAX A/C

MAX A/C-Level

Air is discharged through the face level vents. If the "MAX A/C" mode is selected, the A/C will turn on automatically and "Recirculation" mode will be activated.

1FEATURES OF YOUR HYUNDAI 76

NOTE: o The air intake control switch will change to " " mode when the ignition switch is turned "ON" with the MAX A/C mode selected.

o When you change to another mode from MAX A/C, the A/C and the air intake control switch are set to the following chart.

Air Intake

Control Switch

or *

A/C

ON

ON or OFF *

ON or OFF *

ON

ON

* The A/C or the air intake control switch return

to its former setting.

HEATING CONTROLS

BI-LEVEL HEATING

B690A02S-AAT

B700A02E-AAT

B690A01GK-A

B700A01GK-A

For normal heating operation, set the air intake control to the "Fresh" position and the air flow control to "Floor".

For faster heating, the air intake control should be in the "Recirculation" position.

If the windows fog up, move the air flow control to the "Def" (defroster) position. (The A/C will turn on automatically and "Fresh" mode will be activated.)

For maximum heat, rotate the temperature control to the farthest right position.

Your Hyundai is equipped with bi-level heating controls. To use this feature:

o Set the air intake control to the fresh air ( )

position.

position.

speed.

o Set the air flow control at the bi-level ( )

o Adjust the fan speed control to the desired

o Set the temperature control between "Cool"

and "Warm".

VENTILATION

B710A01S-AAT

AIR CONDITIONING SYSTEM

FEATURES OF YOUR HYUNDAI

77

B740A01S-AAT Air Conditioning Switch (If installed)

B740B01S-AAT Air Conditioning Operation Cooling

To operate the ventilation system:

B710A01GK-A

o Set the air intake control to "Fresh" mode

( ).

o To direct all intake air to the instrument panel

vents, set the airflow control to "Face".

o Adjust the fan speed control to the desired

o Set the temperature control between "Cool"

speed.

and "Warm".

The air conditioning is turned on or off by pushing the A/C button on the heating/air con- ditioning control panel.

HGK2089-1

HGK002-1
To use the air conditioning to cool the interior:

o Set the side vent control to " ", to shut off

outside air entry.

o Turn on the fan control switch. o Turn on the air conditioning switch by push- ing in on the switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control to "Fresh" mode

( ).

1FEATURES OF YOUR HYUNDAI 78

o Set the temperature control to "Cool". ("Cool" provides maximum cooling. The tempera- ture may be moderated by moving the con- trol toward "Warm".)

o Adjust the fan control to the desired speed. For greater cooling, turn the fan control to one of the higher speeds or temporarily select the "Recirculation" position on the air intake control.

B740C01S-AAT Dehumidified Heating

B730A01FC-AAT Operation Tips

o To keep dust or unpleasant fumes from entering the car through the ventilation sys- tem, temporarily set the air intake control to "Recirculation". Be sure to return the control to "Fresh" when the irritation has passed to keep fresh air in the vehicle. This will help keep the driver alert and comfortable.

o Air for the heating/cooling system is drawn in through the grilles just ahead of the wind- shield. Care should be taken that these are not blocked by leaves, snow, ice or other obstructions.

o To prevent interior fog on the windshield, set the air intake control to the fresh air ( ) position and fan speed to the desired posi- tion.

For dehumidified heating:

B740C01GK-A

o Turn on the fan control switch. o Turn on the air conditioning switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control to "Fresh" mode

( ).

o Set the air flow control to "Face". o Adjust the fan control to the desired speed. o For more rapid action, set the fan at one of

the higher speeds.

o Adjust the temperature control to provide the

desired amount of warmth.

DEFROSTING/DEFOGGING

B720A02FC-GAT

A Type

B Type

A Type

B Type

FEATURES OF YOUR HYUNDAI

79

B720A01GK-1

B720A02GK-1

Use the heating/ventilation system to defrost or defog the windshield:

To remove interior fog on the windshield: o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and "Fresh" mode will be activated)

o Set the temperature control to the desired position. o Set the fan speed control between "1" and "4" position.

To remove frost or exterior fog on the windshield:

o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and "Fresh" mode will be activated.)

o Set the temperature control to warm. o Set the fan speed control to position "3" or "4".

NOTE: When the A/C is operated continuously on the floor-defrost level ( ) or defrost level ( ), it may cause fog to form on the exterior windshield. If this occurs, set the air flow control to the face level position ( ) and fan speed control to the low position.

1FEATURES OF YOUR HYUNDAI 80

AUTOMATIC HEATING AND COOLING CONTROL SYSTEM

B970A01Y-AAT (If lnstalled)

Your Hyundai is equipped with an automatic heating and cooling control system controlled by simply setting the desired temperature.

B970B02GK-GAT Heating and Cooling Controls

TYPE A (Without Air Quality System)

TYPE B (With Air Quality System)

HGK2101

HGK2102

1. Temperature Control Button 2. Air Conditioning Switch 3. Display Window 4. Fan Speed Control Switch 5. Air Flow Control Switch 6. AUTO (Automatic Control) Switch

7. Defroster Switch 8. OFF Switch 9. Air lntake Control Switch 10.Ambient Temperature Switch 11.Rear Window Defroster Switch 12.Air Quality System Switch (If installed)

B970C02E-AAT Automatic Operation

FEATURES OF YOUR HYUNDAI

81

NOTE: If the battery has been discharged or dis- connected, the temperature mode will reset to centigrade degrees. This is a normal condition and you can change the temperature mode from centi- grade to farenheit as follows; Press the TEMP button down 3 seconds or more with the button held down. The display shows that the unit of temperature is adjusted to centigrade or fahrenheit. (°C →→→→→ °F or °F →→→→→ °C)

OUTSIDE

TEMP

HGK2106

The FATC (Full Automatic Temperature Con- trol) system automatically controls heating and cooling as follows:

1. Push the "AUTO" switch. The indicator light will illuminate confirming that the Face, Floor and/or Bi-Level modes as well as the blower speed and, air conditioner will be controlled automatically.

HGK2103

2. Push the "TEMP" button to set the desired

temperature. The temperature will increase to the maxi- mum 90°F(32°C) by pushing on the button. Each push of the button will cause the tem- perature to increase by 1°F(0.5°C). The temperature will decrease to the mini- mum 62°F(17°C) by pushing on the button. Each push of the button will cause the tem- perature to decrease by 1°F(0.5°C).

Photo sensor

HGK2076

NOTE: Never place anything over the sensor which is located on the instrument panel to en- sure better control of the heating and cool- ing system.

1FEATURES OF YOUR HYUNDAI 82

B995A01Y-GAT Ambient Temperature Switch

B980A01Y-AAT MANUAL OPERATION

B980B01Y-AAT Fan Speed Control Switch

The heating and cooling system can be con- trolled manually as well by pushing buttons other than the "AUTO" button. In this state, the system sequentially works according to the order of buttons selected. The function of the buttons which are not se- lected will be controlled automatically. Press the "AUTO" button in order to convert to automatic control of the system.

HGK2109

Pressing the button displays the ambient temperature on the display.

OUTSIDE

TEMP

HGK2104

The fan speed can be set to the desired speed by pressing the appropriate fan speed control button. The higher the fan speed is, the more air is delivered. Pressing the "OFF" button turns off the fan.

B670C02GK-AAT Air Intake Control Switch (Without A.Q.S)

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function selected.

B980C02GK-GAT Air Intake Control Switch (With A.Q.S) (If Installed)

FEATURES OF YOUR HYUNDAI

83

With the "Recirculation" mode selected, air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: It should be noted that prolonged opera- tion of the heating system in "recirculation" mode will give rise to fogging of the wind- shield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Recirculation" mode selected may result in the air within the passenger compartment becoming exces- sively dry.

This is used to select fresh outside air or recirculate inside air automatically.

HGK2110

: OFF : ON

Fresh mode :

Air enters the vehicle from the outside and is heated or cooled according to the function selected.

HGK2110-1

This is used to select fresh outside air or recirculation inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FRESH MODE ( ) : The indicator light on the button goes on when the air intake control is in fresh mode.

RECIRCULATION MODE ( ) : The indica- tor light on the button is illuminated when the air intake control is in recirculation mode.

1FEATURES OF YOUR HYUNDAI 84

Recirculation mode :

Air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

Exhaust gas cutoff mode :

Air enters the vehicle from the outside. But if exhaust gas enters the vehicle from the outside, the exhaust gas cutoff mode ( ) is automatically converted to the mode, to prevent exhaust gas from entering the vehicle.

NOTE: It should be noted that prolonged opera- tion of the heating system in recirculation mode ( ) will give rise to misting of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the recirculation mode ( ) selected may result in the air within the passenger compartment becom- ing excessively dry.

CAUTION:

If the windows fog up with the Recircula- tion or A.Q.S mode selected, set the air intake control to the Fresh air position or A.Q.S control to "OFF".

B980E01GK-GAT Air Flow Control

B980D01Y-AAT Heating and Cooling System Off

Press the "OFF" button to stop the operation of the heating and cooling system.

HGK2105
This is used to direct the flow of air. Air can be directed to the floor, instrument panel outlets, or windshield. Four symbols are used to represent Face, Bi-Level, Floor and Floor-Defrost air position.

FEATURES OF YOUR HYUNDAI

85

Face-Level

Bi-Level

Floor-Level

HGK2095

HGK2096

HGK2097

When selecting the "Face" mode, the indicator light will come on, causing air to be discharged through the face level vents.

When selecting the "Bi-Level" mode, the indica- tor light will come on and the air will be dis- charged through the face vents and the floor vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.

When selecting the "Floor-Level" mode, the indicator light will come on and the air will be discharged through the floor vents, windshield defroster nozzle, side defroster nozzle, side ventilator.

1FEATURES OF YOUR HYUNDAI 86

B980F02E-AAT Defrost Switch

CLIMATE CONTROL AIR FILTER (IN FRONT OF BLOWER UNIT)

B760A06GK-AAT (If Installed)

Outside air

Inside air

Filter

HGK2098

Floor-Defrost Level

When selecting the "Floor-Defrost" mode, the indicator light will come on and the air will be discharged through the windshield defrost nozzle, the floor vents, side defroster nozzle, side ventilator.

HGK012
When the "Defrost" button is pressed, the " " mode will be automatically selected and the air will be discharged through the windshield de- frost vents. To assist in defrosting, the air conditioning will operate if ambient temperature is higher than 38.3 °F (3.5 °C) and automatically turns off if the ambient temperature drops below 38.3 °F (3.5 °C).

Inside air

Blower fan

Evaporator core

Heater core

B760A01E

The climate control air filter is located in front of the blower uniit behind the glove box. It operates to decrease the amount of pollutants entering the car. To replace the climate control air filter, refer to the page 6-18.

FEATURES OF YOUR HYUNDAI

87

CAUTION:

o Replace the filter every 10,000 miles (15,000 km) or once a year. If the car is being driven in severe conditions such as dusty, rough roads, more frequent climate control air filter inspections and changes are required.

o When the air flow rate is decreased, the system should be checked at an autho- rized dealer.

o If your vehicle is not equipped with this filter, it can be installed by your dealer. Check with your dealer for details.

1FEATURES OF YOUR HYUNDAI 88

STEREO SOUND SYSTEM

B750A02A-AAT How Car Audio Works FM reception

Ionosphere

B750A01L AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures the best possible quality repro- duction. However, in some cases the signal coming to your vehicle may not be strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.

AM reception

Ionosphere

FM radio station

Mountains

Unobstructed

area

B750A02L AM broadcasts can be received at greater distances than FM broadcasts. This is because AM radio waves are transmitted at low frequen- cies. These long, low frequency radio waves can follow the curvature of the earth rather than travelling straight out into the atmosphere. In addition, they curve around obstructions so that they can provide better signal coverage.

Buildings

Obstructed area

Iron bridges

B750A03L

FM broadcasts are transmitted at high frequen- cies and do not bend to follow the earth's surface. Because of this, FM broadcasts gen- erally begin to fade at short distances from the station. Also, FM signals are easily affected by buildings, mountains, or other obstructions. These can result in certain listening conditions which might lead you to believe a problem exists with your radio. The following conditions are normal and do not indicate radio trouble:

FEATURES OF YOUR HYUNDAI

89

B750B05Y-AAT Using a cellular phone or a two-way radio

When a cellular phone is used inside the vehicle, noise may be produced from the audio equip- ment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.

WARNING:

Hyundai recommends that you never use a cell phone while driving. This could result in loss of control, and an accident that may cause death, serious injury, or property damage. You must stop at a safe place to use a cellular phone.

NOTE: Some states and cities have regulations prohibiting the use of cell phones while driving. You should be aware of the specific requirements in your area.

B750A04L

B750A05L

o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another stronger station.

o Flutter/Static - Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.