2006 Hyundai Tiburon Owners Manual

HGK102
1. Push the "PANIC" button on the transmitter. 2. At the same time, the siren will sound and the turn signal lights will blink for 30 seconds. 3. To turn off the system, push the "PANIC"

button again on the transmitter.

B070F02A-AAT KEYLESS ENTRY SYSTEM (If installed) NOTE: This device complies with Part 15 of the FCC rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including inter- ference that may cause undesired opera- tion.

WARNING:

Changes or modifications not expressly approved by the party responsible for com- pliance could void the user's authority to operate the equipment.

NOTE: The transmitter will not work if any of fol- lowing occur: - The ignition key is in ignition switch. - You exceed the operating distance limit

(10 m).

- The battery in the transmitter is weak. - Other vehicles or objects may be block-

ing the signal.

- The weather is extremely cold. - The transmitter is close to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.

When the transmitter does not work cor- rectly, open and close the door with the ignition key. If you have a problem with the transmitter, contact an authorized Hyundai Dealer.

NOTE: Keep the transmitter away from water or any liquid. If the keyless entry system is inoperative due to exposure to water or liquids, it will not be covered by your manu- facturer vehicle warranty.

Locking doors

1. Close all doors. 2. Push the "LOCK" button on the transmitter. 3. At the same time all doors lock, the turn signal lights will blink once to indicate that the system is armed.

Unlocking doors

1. Push the "UNLOCK" button on the transmitter. 2. At the same time all doors unlock, the turn signal lights will blink twice to indicate that the system is disarmed.

B070E02GK-GAT Replacing the battery

When the transmitter's battery begins to get weak, it may take several pushes on the button to lock or unlock the doors, and the LED will not light. Replace the battery as soon as possible.

Battery type : CR2016

Replacement instructions:

Screwdriver

HGK122

1. Carefully separate the case with a blade

screwdriver as shown in the illustration.

FEATURES OF YOUR HYUNDAI

POWER WINDOW

B050A01GK-AAT

Battery

HGK121

(1)

2. Remove the old battery from the case and note the polarity. Make sure the polarity of the new battery is the same(+side facing up), then insert it in the transmitter.

NOTE: Install a new battery within 30 seconds after removing the old one. If installing a new battery takes more than 30 seconds, take the following steps.

1) Turn the ignition key to the "ACC" posi-

tion.

2) Make sure that the turn signal lamps blink once by pushing the "LOCK" or "UNLOCK" button on the transmitter.

HGK2015
The power windows operate only when the ignition key is in the "ON" position. The main switches are located on the driver's arm rest and control the front windows on the respective sides of the vehicle. The windows may be opened by depressing the front portion of the switch. To stop at the desired opening, release the switch. The window may be closed by pulling the front portion of the switch. In order to prevent operation of the passenger front window by the passenger, a window lock switch (1) is provided on the arm rest of the driver's door. To disable the passenger's power window, push the win- dow lock switch. To revert to normal operation, push in on the window lock switch again.

1FEATURES OF YOUR HYUNDAI 10

SEATS

Auto-Down Window (Driver's Side) (If Installed)

B080A02A-AAT ADJUSTABLE FRONT SEATS

WARNING:

o Never adjust the driver’s seat while the vehicle is moving. Any sudden or unex- pected movement of the seat could cause you to lose control of the vehicle result- ing in an accident. Only adjust the driver’s seat when the vehicle is station- ary.

o Do not sit or lean unnecessarily close to the airbag. Position the seat so that you can sit as far back as possible from the airbag and still comfortably reach all controls.

B050A02GK The Auto-Down window is moved to its fully open position by pushing the switch. To stop at the desired position push in on the switch again.

HGK2016

WARNING:

(1)Be careful that someone's head, hands and body are not trapped by a closing window.

(2)Never try to operate the main switch on the driver's door and the individual door window switch in opposing directions at the same time. If this is done, the window will stop and cannot be opened or closed.

(3)Do not leave children alone in the car. Always remove the ignition key for their safety.

FEATURES OF YOUR HYUNDAI

11

B080C02A-AAT Adjusting Seatback Angle

B080B03A-AAT Adjusting Seat Forward and Rearward

WARNING:

After adjusting the seat, always check that it is securely locked into place by attempt- ing to move the seat forward or reverse without using the lock release lever. Sud- den or unexpected movement of the driver's seat could cause you to lose control of the vehicle resulting in an accident.

HGK2027

To move the seat toward the front or rear, pull the lock release lever upward. This will release the seat on its track so you can move it forward or rearward to the desired position. When you find the position you want, release the lever and slide the seat forward or rearward on its track until it locks into the desired position and cannot be moved further.

HGK2028

To recline the seatback, lean forward to take your weight off it, then pull up on the recliner control lever at the outside edge of the seat. Now lean back until the desired seatback angle is achieved. To lock the seatback into position, release the recliner control lever.

1FEATURES OF YOUR HYUNDAI 12

WARNING:

Riding with a reclined seatback increases your chance of serious or fatal injuries in the event of a collision or sudden stop. The protection of your restraint system (seat belts and airbags) is greatly reduced by reclining your seat. Seat belts must be snug against your hips and chest to work prop- erly. The more the seatback is reclined, the greater the chance that an occupant's hips will slide under the lap belt or the occupant's neck will strike the shoulder belt. Drivers and passengers should always sit well back in their seats, properly belted, and with the seatbacks upright.

B080D02JM-AAT Adjustable Headrests

WARNING:

Lock Knob

HGK2032
Headrests are designed to help reduce the risk of neck injuries. To raise the headrest, pull it up. To lower the headrest, push it down while pressing the lock knob. To remove the headrest, raise it as far as it can go then press the lock knob while pulling upward. This should only be done when the seat is not occupied.

B080D01JM o For maximum effectiveness in case of an accident the headrest should be ad- justed so the middle of the headrest is at the same height as the top of the occupant's eyes. For this reason, the use of a cushion that holds the body away from the seatback is not recom- mended.

o Do not operate vehicle with the head- rests removed as injury to the occupants may occur in the event of an accident. Headrests may provide protection against neck injuries when properly adjusted.

o Do not adjust the headrest hejght while

the vehicle is in motion.

B080E01F-AAT Lumbar Support Control (Driver's seat only)

B080F01F-AAT Seat Cushion Height Adjustment (Driver's Seat Only) (If Installed)

B129A01F-AAT REAR SEAT POSITIONS

FEATURES OF YOUR HYUNDAI

13

SOFT

FIRM

B129A01GK

HGK2030
The driver's seat is equipped with adjustable lumbar support. To increase the amount of lumbar support, pull the lever forward. To decrease it, push the lever toward the rear.

HGK2029
To raise or lower the front part of the seat cushion, turn the knob forward or rearward.

WARNING:

This vehicle contains two rear seating po- sitions only and a seat belt for each seating position. Thus, never permit more than two occupants to ride in the rear seat because an unrestrained occupant could be seri- ously injured or killed in the event of a vehicle crash.

1FEATURES OF YOUR HYUNDAI 14

B130A01GK-AAT REAR SEAT ENTRY (Walk in device)

The driver and front passenger's seatbacks should be tilted to enter the rear seat.

(1)

(1)

(2)

HGK2036
By pulling up the walk in device lever (1) at the left-upper side of the driver side seatback, the seatback will tilt forward. Then pull the lock release lever (2) up to move the seat forward.

HGK2036-1

By pulling up the walk in device lever (1) at the right-upper side of the passenger side seatback, the seatback will tilt forward. Then push the seat forward to allow the occupants to enter.

Recliner Memory By pulling up the walk in device lever (1) the seatback is reclined and returned to the original position.

WARNING:

Don't drive with the passenger side seatback reclined. It is dangerous to move it while driving. Be sure the seatback is caterred firmly before driving.

B099A01F-AAT BEFORE FOLDING THE REAR SEATS

HGK2034
In order to prevent the shoulder belt from being damaged while folding the rear seat, the shoul- der belt must be passed through the hanger to keep it out of the way.

CAUTION:

Seat belts must be removed from the hanger when in use.

B110A02S-AAT FOLDING REAR SEATBACKS

WARNING:

The purpose of the fold-down rear seatbacks is to allow you to carry longer objects than could otherwise be accommo- dated. Never allow passengers to sit on top of the folded down seat back while the car is moving as this is not a proper seating position and no seat belts are available for use. This could result in injury in case of an accident or sudden stop. Objects carried on the folded down seatback should not extend higher than the top of the front seats. This could allow cargo to slide for- ward and cause injury or damage during sudden stops.

HGK2035
The rear seatbacks may be folded to facilitate carrying long items or to increase the luggage capacity of the vehicle.

o To unlock the seatback, push the seatback locking button, then pull forward on the seatback panel.

o When you return the seatback to its upright position, always be sure it has locked into position by pulling and pushing on the top of the seatback.

FEATURES OF YOUR HYUNDAI

15

B140A01S-AAT REAR SEAT WARNING

B140A01GK For the safety of all passengers, luggage or other cargo should not be piled higher than the top of the seatback. In addition, do not place objects on the rear shelf as they may move forward during braking or in an accident and strike vehicle passengers.

1FEATURES OF YOUR HYUNDAI 16

SEAT BELT

B150A02S-AAT SEAT BELT PRECAUTIONS

B150B04Y-AAT Infant or Small Child

WARNING:

All occupants of the vehicle must wear their seat belts at all times. Seat belts and child restraints reduce the risk of serious or fatal injuries for all occupants in the event of a collision or sudden stop. Without a seat belt, occupants could be shifted too close to a deploying airbag, strike the interior structure or be thrown from the vehicle. Properly worn seat belts greatly reduce these hazards. Even with advanced airbags, unbelted occupants can be severely in- jured by a deploying airbag. Always follow the precautions about seat belts, airbags and occupant safety contained in this manual.

All 50 states have child restraint laws. You should be aware of the specific requirements in your state. Child and/or infant safety seats must be properly placed and installed in the rear seat. Information about the use of these restraints begins on page 1-21.

WARNING:

Every person in your vehicle needs to be properly restrained at all times, including infants and children. Never hold a child in your arms or lap when riding in a vehicle. The violent forces created during a crash will tear the child from your arms and throw the child against the interior. Always use a child restraint appropriate for your child's height and weight, see page 1-21.

NOTE: Small children are best protected from in- jury in an accident when properly restrained in the rear seat by a child restraint system that meets the requirements of the Federal Motor Vehicle Safety Standards. Before buying any child restraint system, make sure that it has a label certifying that it meets Federal Motor Vehicle Safety Stan- dard 213. The restraint must be appropriate

for your child's height and weight. Check the label on the child restraint for this information. See page 1-21.

B150C02A-AAT Larger Children

Children who are too large for child restraint systems should always occupy the rear seat and use the available lap/shoulder belts. The lap portion should be fastened snug on the hips and as low as possible. Check belt fit periodically. A child's squirming could put the belt out of posi- tion. Children are afforded the most safety in the event of an accident when they are restrained by a proper restraint system in the rear seat. If a larger child (over age 13) must be seated in the front seat, the child should be securely restrained by the available lap/shoulder belt and the seat should be placed in the rearmost position. Children under the age of 13 should be restrained securely in the rear seat. Never place a child under the age of 13 in the front seat. NEVER place a rear facing child seat in the front seat of a vehicle.

B150D01A-AAT Pregnant Women

B150G02A-AAT Do Not Lie Down

The use of a seat belt is recommended for pregnant women to lessen the chance of injury in an accident. When a seat belt is used, the lap belt portion should be placed as low and snugly as possible on the hips, not across the abdo- men. For specific recommendations, consult a physician.

To reduce the chance of injuries in the event of an accident and to achieve maximum effective- ness of the restraint system, all passengers should be sitting up and the front seats should be in an upright position when the car is moving. A seat belt cannot provide proper protec-tion if the person is lying down in the rear seat or if the front seat is in a reclined position.

B150E01A-AAT Injured Person

A seat belt should be used when an injured person is being transported. When this is nec- essary, you should consult a physician for recommendations.

B150F01A-AAT One Person Per Belt

Two people (including children) should never attempt to use a single seat belt. This could increase the severity of injuries in case of an accident.

WARNING:

Riding with a reclined seatback increases your chance of serious or fatal injuries in the event of a collision or sudden stop. The protection of your restraint system (seat belts and airbags) is greatly reduced by reclining your seat. Seat belts must be snug against your hips and chest to work prop- erly. The more the seatback is reclined, the greater the chance that an occupant's hips will slide under the lap belt causing serious internal injuries or the occupant's neck could strike the shoulder belt. Drivers and passengers should always sit well back in their seats, properly belted (see page 1-19), and with the seatbacks upright.

FEATURES OF YOUR HYUNDAI

17

B160A02A-AAT CARE OF SEAT BELTS

Seat belt systems should never be disassembled or modified. In addition, care should be taken to assure that seat belts and belt hardware are not damaged by seat hinges, doors or other abuse.

WARNING:

When you return the rear seatback to its upright position after the rear seatback was folded down, be careful not to damage the seat belt webbing or buckle. Be sure that the webbing or buckle does not get caught or pinched in the rear seat. A seat belt with damaged webbing or buckle will not be as strong and could possibly fail during a collision or sudden stop, resulting in seri- ous injury.

B160B01A-AAT Periodic Inspection

It is recommended that all seat belts be in- spected periodically for wear or damage of any kind. Parts of the system that are damaged should be replaced as soon as possible.

1FEATURES OF YOUR HYUNDAI 18

B160C01A-AAT Keep Belts Clean and Dry

Seat belts should be kept clean and dry. If belts become dirty, they can be cleaned by using a mild soap solution and warm water. Bleach, dye, strong detergents or abrasives should not be used because they may damage and weaken the fabric.

B160D01A-AAT When to Replace Seat Belts

Entire in-use seat belt assembly or assemblies should be replaced if the vehicle has been involved in an accident. This should be done even if no damage is visible. Additional ques- tions concerning seat belt operation should be directed to your Hyundai Dealer.

B170A04A-AAT HEIGHT ADJUSTABLE FRONT SEAT SHOULDER BELT

Release the button to lock the anchor into position. Try sliding the height adjuster to make sure that it has locked into the position.

WARNING:

o Verify the shoulder belt anchor is locked into position at the appropriate height. Never position the shoulder belt across your neck or face. Improperly posi- tioned seat belts can cause serious inju- ries in an accident.

o Failure to replace seat belts after an accident could leave you with damaged seat belts that will not provide protec- tion in the event of another collision leading to personal injury or death. Replace your seat belts after being in an accident as soon as possible.

HGK2038
You can adjust the height of the shoulder belt anchor to one of the 4 positions for maximum comfort and safety. If the height of the adjusting seat belt is too near your neck, you will not be getting the most effective protection. The shoulder portion should be adjusted so that it lies across your chest and midway over your shoulder nearest the door and not your neck. To adjust the height of the seat belt anchor, lower or raise the height adjuster into an appro- priate position. To raise the height adjuster, pull it up. To lower it, push it down while pressing the height adjuster button.

B180A01L-AAT SEAT BELT-Driver's 3-Point System with Emergency Locking Retractor: To Fasten Your Belt

NOTE: Seat belt reminder light comes and stays on until the seat belt is fastened when the ignition key is turned "ON" or "START". And, the warning chime will also sound for about 6 seconds.

B190A02Y-AAT SEAT BELTS -Front Passenger and Rear Seat 3-Point System with Combination Locking Retractor To Fasten Your Belt

Combination retractor type seat belts are in- stalled in the rear seat positions to help accom- modate the installation of child restraint sys- tems. Hyundai strongly recommends that chil- dren always be seated in the rear seat. NEVER place any infant restraint system in the front seat of the vehicle. This type of seat belt combines the features of both an emergency locking retractor seat belt and an automatic locking retractor seat belt. To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle. There will be an audible "click" when the tab locks into the buckle.

B180A01L

To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle. There will be an audible "click" when the tab locks into the buckle. The seat belt automatically adjusts to the proper length only after the lap belt portion is adjusted manually so that it fits snugly around your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. If there is a sudden stop or impact, however, the belt will lock into position. It will also lock if you try to lean forward too quickly. Check to make sure that the belt is properly locked and that the belt is not twisted.

FEATURES OF YOUR HYUNDAI

19

When not securing a child restraint, the seat belt operates in the same way as the driver's seat belt (Emergency Locking Retractor Type). It automatically adjusts to the proper length only after the lap belt portion of the seat belt is adjusted manually so that it fits snugly around your hips. When the seat belt is fully extended from the retractor to allow the installation of a child restraint system, the seat belt operation changes to allow the belt to retract, but not to extend. (Automatic Locking Retractor Type) see page 1-25.

NOTE: Although the combination retractor pro- vides the same level of protection for seated passengers in either emergency or auto- matic locking modes, it is recommended that seated passengers use the emergency locking feature for improved convenience. The automatic locking function is intended to facilitate child restraint installation. To convert from the automatic locking feature to the emergency locking operation mode, allow the unbuckled seat belt to fully re- tract.

1FEATURES OF YOUR HYUNDAI 20

WARNING:

o For maximum restraint system protec- tion, seat belts must always be used whenever the car is moving.

o Seat belts are most effective when

seatbacks are in the upright position.

o Children age 12 and younger must al- ways be properly restrained in the rear seat. Never allow children to ride in the front passenger seat. If a child over 13
must be seated in the front seat, he/she must be properly belted and the seat should be moved as far back as possible. o Never wear the shoulder belt under your arm or behind your back. An improperly positioned shoulder belt can cause se- rious injuries in a crash. The shoulder belt should be positioned midway over your shoulder across your collarbone. o Avoid wearing twisted seat belts. A twisted belt can't do its job as well. In a collision, it could even cut into you. Be sure the belt webbing is straight and not twisted.

o Be careful not to damage the belt web- bing or hardware. If the belt webbing or hardware is damaged, replace it.

B200A01A-AAT Adjusting Your Seat Belt

B210A01A-AAT To Release the Seat Belt

B210A01L The seat belt is released by pressing the re- lease button in the locking buckle. When it is released, the belt should automatically draw back into the retractor. If this does not happen, check the belt to be sure it is not twisted, then try again.

B200A01L

WARNING:

You should place the lap belt portion as low as possible and snugly across your hips, not on your waist. If the lap belt is located too high on your waist, it may increase the chance of injury in the event of a collision. Both arms should not be under or over the belt. Rather, one should be over and the other under, as shown in the illustration. Never wear the seat belt under the arm nearest the door.

CHILD RESTRAINT SYSTEM

B230A04A-AAT Children riding in the car should sit in the rear seat and must always be properly restrained to minimize the risk of injury in an accident, sudden stop or sudden maneuver. According to acci- dent statistics provided by the National High- way Traffic Safety Administration (NHTSA), children are safer when properly restrained in the rear seats than in the front seat. Larger children not in a child restraint should use one of the seat belts provided. All 50 states have child restraint laws. You should be aware of the specific requirements in your state. Child and/or infant safety seats must be properly placed and installed in the rear seat. You must use a commercially available child restraint system that meets the requirements of the Federal Motor Vehicle Safety Standards (FMVSS). Children could be injured or killed in a crash if their restraints are not properly secured. For small children and babies, a child seat or infant seat must be used. Before buying a particular child restraint system, make sure it fits your car and seat belts, and fits your child. Follow all the instructions provided by the manufacturer when installing the child restraint system.

WARNING:

o A child restraint system must be placed in the rear seat. Never install a child or infant seat on the front passenger's seat. Should an accident occur and cause the passenger side airbag to deploy, it could severely injure or kill an infant or child seated in an infant or child seat. Thus only use a child restraint in the rear seat of your vehicle.

o A safety belt or child restraint system can become very hot if it is left in a closed vehicle on a sunny day, even if the out- side temperature does not feel hot. Be sure to check the seat cover and buckles before placing a child there.

o When the child restraint system is not in use, store it in the trunk or fasten it with a safety belt so that it will not be thrown forward in the case of a sudden stop or an accident.

o Children may be seriously injured or killed by an inflating airbag. All children, even those too large for child restraints, must ride in the rear seat.

FEATURES OF YOUR HYUNDAI

21

WARNING:

To reduce the chance or serious or fatal injuries: o Children of all ages are safer when re- strained in the rear seat. A child riding in the front passenger seat can be force- fully struck by an inflating airbag result- ing in serious or fatal injuries.

o Always follow the instructions for in- stallation and use of the child restraint maker.

o Always make sure the child seat is se- cured properly in the car and your child is securely restrained in the child seat. o Never hold a child in your arms or lap when riding in a vehicle. The violent forces created during a crash will tear the child from your arms and throw the child against the car’s interior.

o Never put a seat belt over yourself and a child. During a crash, the belt could press deep into the child causing seri- ous internal injuries.

o Never leave children unattended in a vehicle – not even for a short time. The car can heat up very quickly, resulting in serious injuries to children inside. Even very young children may inadvertently cause the vehicle to move, entangle them- selves in the windows, or lock them- selves or others inside the vehicle.

1FEATURES OF YOUR HYUNDAI 22

WARNING:

o Never allow two children, or any two

persons, to use the same seat belt.

o Children often squirm and reposition themselves improperly. Never let a child ride with the shoulder belt under their arm or behind their back. Always prop- erly position and secure children in rear seat.

o Never allow a child to stand-up or kneel on the seat or floorboard of a moving vehicle. During a collision or sudden stop, the child can be violently thrown against the vehicles interior, resulting in serious injury.

o Never use an infant carrier or a child safety seat that "hooks" over a seatback, it may not provide adequate security in an accident.

o Seat belts can become very hot, espe- cially when the car is parked in direct sunlight. Always check seat belt buck- les before fastening them over a child. o Always store or secure a child seat, even when it is not in use. During a collision or sudden stop, the child seat could be thrown inside the vehicle.

B230B02GK-GAT Using a Child Restraint System For small children and babies, the use of a child seat or infant seat is required. This child seat or infant seat should be of appropriate size for the child and should be installed in accordance with the manufacturer's instructions. It is further required that the seat be placed in the vehicle's rear seat since this can make an important contribution to safety. Your vehicle is provided with two child restraint hook holders for insta lling the child seat or infant seat.

B230C05F-AAT Installing a Child Restraint Seat with the "Tether Anchorage" System

Two child restraint hook holders are located on the luggage compartment floor.

To install the child restraint seat

Tether Anchor Cover

Child Restraint Hook Holder

B230E02GK

1. Open the tether anchor cover on the rear

luggage compartment floor.

2. Route the child restraint seat strap over the

seatback. For vehicles with adjustable headrests, route the tether strap under the headrest and between the headrest posts, otherwise route the tether strap over the top of the seatback.

WARNING:

o A child can be seriously injured or killed in a collision if the child restraint is not properly anchored. Always follow the child seat manufacturer’s instructions for installation and use.

o Never mount more than one child re- straint to a single tether or to a single lower anchorage point. The increased load caused by multiple seats may cause the tethers or anchorage points to break, causing serious injury or death.

Rear luggage compartment floor

Blanking covers

Covering shelf

Child Restraint Hook Holders

Tether strap hook

Front of Vehicle

B230E01GK 3. Remove the blanking covers on the cover-

ing shelf.

4. Connect the tether strap hook to the child restraint hook holder through the hole on the covering shelf and tighten to secure the seat.

FEATURES OF YOUR HYUNDAI

23

B230D03GK-AAT Securing the child Restraint seat with the "ISOFIX" system

B230F01GK

Some child seat manufacturers make child restraint seats that are labeled as ISOFIX or ISOFIX-compatible child restraint seats. These seats include two rigid or webbing mounted attachments that connect to two ISOFIX an- chors at specific seating positions in your ve- hicle. This type of child restraint seat eliminates the need to use seat belts to attach the child seat for forward-facing child restraint seats. ISOFIX anchors have been provided in your vehicle. The ISOFIX anchors are located in the left and right outboard rear seating positions. Their locations are shown in the illustration.

1FEATURES OF YOUR HYUNDAI 24

WARNING:

o There is no center rear seat position. o A child can be seriously injured or killed in a collision if the child restraint is not properly anchored. Always follow the child seat manufacturer’s instructions for installation and use.

o Never install a child restraint using the ISOFIX anchors at the center position of the rear seat. In a crash, the ISOFIX anchors may break if a car seat is improp- erly placed in the center position result- ing in serious or fatal injuries. Only place a ISOFIX or ISOFIX-compatible child seat in the left or right out-board rear seating positions (as shown) to the appropriate ISOFIX anchors provided.

o Never mount more than one child re- straint to a single tether or to a single lower anchorage point. The increased load caused by multiple seats may cause the tethers or anchorage points to break, causing serious injury or death.

o When using the vehicle’s “ISOFIX” sys- tem to install a child restraint system in the rear seat, all unused vehicle rear seat belt metal latch plates or tabs must be latched securely in their seat belt buck- les and the seat belt webbing must be retracted behind the child restraint to prevent the child from reaching and tak- ing hold of unretracted seat belts. Unlatched metal latch plates or tabs may allow the child to reach the unretracted seat belts which may result in strangu- lation and a serious injury or death to the child in the child restraint.

ISOFIX Anchor

ISOFIX Anchor Position Indicator

B230D02GK The ISOFIX anchors are located between the seatback and the seat cushion of the rear seat left and right outboard seating positions.

!

WARNING:

A child can be seriously injured or killed in a collision if the child restraint is not prop- erly anchored to the car and the child is not properly restrained in the child restraint. Always follow the child seat manufacturer’s instructions for installation and use.

HGK261

Follow the child seat manufacturer's instruc- tions to properly install child restraint seats with ISOFIX or ISOFIX-compatible attachments.

Once you have installed the ISOFIX child re- straint, assure that the seat is properly attached to the ISOFIX and tether anchors. Also, test the child restraint seat before you place the child in it. Tilt the seat from side to side. Also try to tug the seat forward. Check to see if the anchors hold the seat in place.

FEATURES OF YOUR HYUNDAI

25

B230G02O-AAT Child Restraint System Installation on outboard Rear Seats On outboard rear seats

HGK1010
To install a child restraint system in the outboard rear seats, extend the shoulder/lap belt entirely from its retractor until a "click" is felt. This will engage the seat belt retractor automatic locking feature, which allows the seat belt to retract but not extend. Install the child restraint system, buckle the seat belt and allow the seat belt to take up any slack. Make sure that the lap portion of the belt is tight around the child restraint system and the shoulder portion of the belt is positioned so that it can not interfere with the child's head or neck. Also, double check to be sure that the retractor has engaged the auto- matic locking feature by trying to extend web- bing out of the retractor.

1FEATURES OF YOUR HYUNDAI 26

If the retractor is in the automatic locking mode, the belt will be locked. After installation of the child restraint system, try to move it in all directions to be sure the child restraint system is securely installed. If you need to tighten the belt, pull more webbing toward the retractor. When you unbuckle the seat belt and allow it to retract, the retractor will automatically revert back to its normal seated passenger emer- gency locking usage condition.

NOTE: o Before installing the child restraint sys- tem in any seating position, read the instructions supplied by the child re- straint system manufacturer.

o If the seat belt does not operate as de- scribed, have the system checked imme- diately by your authorized Hyundai dealer.

! WARNING:

o If the retractor is not in the Automatic Locking mode, the child restraint can move when your vehicle turns or stops suddenly. A child can be seriously in- jured or killed if the child restraint is not properly anchored to the car, including setting the retractor to the Automatic Locking mode.

o Do not install any child restraint system in the front passenger seat. Should an accident occur and cause the passenger side airbag to deploy, it could severely injure or kill an infant or child seated in an infant or child seat. Therefore, only use a child restraint system in the rear seat of your vehicle.

B180B04GK-AAT Pre-tensioner Seat Belt (If Installed)

Your Hyundai vehicle is equipped with driver's and front passenger's pre-tensioner seat belts. The purpose of the pre-tensioner is to make sure that the seat belts fit tightly against the occupant's body in certain frontal collisions. The pre-tensioner seat belts can be activated alone or, where the frontal collision is severe enough, together with the airbags.

HXG229

When the vehicle stops suddenly, or if the occupant tries to lean forward too quickly, the seat belt retractor will lock into position. In certain frontal collisions, the pre-tensioner will activate and pull the seat belt into tighter contact against the occupant's body.

Driver's airbag

Passenger's airbag

WARNING:

To obtain maximum benefit from a pre- tensioner seat belt:

o The seatbelt must be work correctly and adjusted to the proper position (see pages 1-18). Please read and follow all of the important information and precau- tions about your vehicle’s occupant safety features – including seat belts – that are provided in this manual.

o Be sure you and your passengers always wear seat belts and wear them properly.

B180B01GK The seat belt pre-tensioner system consists mainly of the following components.

Their locations are shown in the illustration.

1. SRS airbag warning light 2. Seat belt pre-tensioner assembly 3. SRS control module

FEATURES OF YOUR HYUNDAI

27

NOTE: o Both the driver's and front passenger's pre-tensioner seat belts will be activated in certain frontal collisions. The pre- tensioner seat belts can be activated alone or, where the frontal collision is severe enough, together with the airbags.

o When the pre-tensioner seat belts are activated, a loud noise may be heard and fine dust, which may appear to be smoke, may be visible in the passenger com- partment. These are normal operating conditions and are not hazardous.

o Although it is harmless, the fine dust may cause skin irritation and should not be breathed for prolonged periods. Wash all exposed skin areas thoroughly after an accident in which the pre-tensioner seat belts were activated.

1FEATURES OF YOUR HYUNDAI 28

CAUTION:

AIR BAG

o The sensor that activates the SRS airbag is connected with the pre-tensioner seat belts. The SRS airbag warning light on the instrument panel will illuminate for approximately 6 seconds after the igni- tion key has been turned to the "ON" position, and then it should turn off.

o If the pre-tensioner seat belt is not work- ing properly, this warning light will illu- minate even if there is no malfunction of the SRS airbag system. If the SRS airbag warning light does not illuminate when the ignition key is turned to "ON" or if it remains illuminated after approximately 6 seconds, or if it illuminates while the vehicle is being driven, please have an authorized Hyundai dealer inspect the pre-tensioner seat belts and SRS airbag system as soon as possible.

WARNING:

o Pre-tensioners are designed to operate only one time. After activation, pre- tensioner seat belts must be replaced. All seat belts, of any type, should always be replaced after they have been worn during a collision.

o The pre-tensioner seat belt assembly mechanisms become hot during activa- tion. Do not touch the pre-tensioner seat belt assemblies for several minutes after they have been activated.

o Do not attempt to inspect or replace the pre-tensioner seat belts yourself. This must be done by an authorized Hyundai dealer.

o Do not strike the pre-tensioner seat belt

assemblies.

o Do not attempt to service or repair the pre-tensioner seat belt system in any manner.

o Improper handling of the pre-tensioner seat belt assemblies, and failure to heed the warnings to not strike, modify, in- spect, replace, service or repair the pre- tensioner seat belt assemblies may lead to improper operation or inadvertent activation and serious injury.

o Always wear seat belts when driving or

riding in a motor vehicle.

SUPPLEMENTAL RESTRAINT (AIRBAG) SYSTEM (SRS)

B240A03GK-AAT Driver's Airbag

B240A01GK Your Hyundai is equipped with a Supplemental Restraint (Airbag) System. The indications of the system's presence are the letters "SRS AIR BAG" embossed on the ornament in the steer- ing wheel and the passenger's side front panel pad above the glove box.

The Hyundai SRS consists of airbags installed under the pad covers in the center of the steering wheel and the passenger's side front panel above the glove box. The purpose of the SRS is to provide the vehicle's driver and/or the front passenger with additional protection than that offered by the seat belt system alone, in case of a frontal impact of sufficient severity.

NOTE: o Be sure to read information about the SRS on the labels provided on the front of the sun visor and in the glove box.

o If you are considering modification of your vehicle due to a disability, please contact the Hyundai Customer Assis- tance Center at 1-800-633-5151.

WARNING:

Always use seat belts and child restraints – every trip, every time, everyone! Airbags inflate with considerable force and in the blink of an eye. Seat belts help keep occu- pants in proper position to obtain maxi- mum benefit from the airbag. Always fol- low the precautions about seat belts, airbags and occupant safety contained in this manual.

To reduce the chance of serious or fatal injuries and receive the maximum safety benefit from your restraint system: o Never place a child in any child or booster seat in the front seat (see child restraints 1-21).

o ABC – Always Buckle Children in the back seat. It is the safest place for children of any age to ride

o Front and side impact airbags can injure occupants improperly positioned in the front seats

WARNING:

o Move your seat as far back as practical from the front airbags, while still main- taining control of the vehicle.

o Never sit or lean unnecessarily close to

the front or side airbags

o Never lean against the door or center console – always sit in an upright posi- tion

o Never place objects over or near any airbag module (front or side impact airbags), because these objects can in- jure passengers in a crash

o Never place covers, blankets or after- market seat warmers on the passenger seat as these may interfere with the occupant classification system

o Do not tamper or disconnect SRS wiring or other components. Injuries could result from inadvertent deployment or failure of the airbag to deploy in a crash. o If the SRS airbag warning light (see pg 1- 40) remains illuminated while the vehicle is being driven, have an authorized Hyundai dealer inspect the airbag sys- tem as soon as possible.

o Airbags can only be used once – have an authorized Hyundai dealer replace the airbag immediately after deployment.

FEATURES OF YOUR HYUNDAI

29

WARNING:

o The SRS is designed to deploy the airbags only when an impact is suffi- ciently severe and when the impact angle is less than 30° from the forward longi- tudinal axis of the vehicle and will not deploy in side, rear or rollover impacts. Additionally, the airbags will only de- ploy once. Thus, seat belts must be worn at all times.

o Front airbags are not intended to deploy in light collisions in which protection can be provided by the seat belt alone.

Rear impact

Side Impact

Rollover

B240A02GK

1FEATURES OF YOUR HYUNDAI 30

WARNING:

o Front airbags are not intended to deploy in side-impact, rear-impact or rollover crashes. In addition, airbags will not deploy in frontal crashes below the de- ployment threshold speed.

o Move your seat as far back as practical from the front airbags, while still main- taining control of the vehicle. You and your passengers should never sit or lean unnecessarily close to the airbags. Im- properly positioned drivers and passen- gers can be severely injured by inflating airbags.

o No objects should be placed over or near the airbag modules on the steering wheel, instrument panel, and the front passenger's panel above the glove box, because any such object could cause harm if the vehicle is in a crash severe enough to cause the airbags to deploy. o If the airbags deploy, they must be re- placed by an authorized Hyundai dealer. Deployed airbags WILL NOT inflate again and will provide no protection in subse- quent collisions.

o Do not tamper with or disconnect SRS wiring, or other components of the SRS system. Doing so could result in injury, due to accidental firing of the airbags or by rendering the SRS inoperative.

WARNING:

o Do not install a child restraint system in the front passenger seat position. A child restraint system must never be placed in the front seat. The infant or child could be severely injured or killed by an airbag deployment in case of an accident.

o Do not allow children to ride in the front passengrer seat. If older children (teen- agers and older) must ride in the front seat, make sure they are always properly belted and that the seat is moved back as far as possible.

o For maximum safety protection in all types of crashes, all occupants includ- ing the driver should always wear their seat belts whether or not an airbag is also provided at their seating position to minimize the risk of severe injury or death in the event of a crash. Do not sit or lean unnecessarily close to the airbag while the vehicle is in motion.

o The SRS airbag system must deploy very rapidly to provide protection in a crash. If an occupant is out of position because of not wearing a seat belt, the airbag may forcefully contact the occupant causing serious or fatal injuries.

B240B04GK-AAT SRS Components and Functions

The SRS consists of the following components:

B240B01L

- Driver's Airbag Module - Passenger's Airbag Module - Knee Bolster - SRS Service Reminder Indicator (SRI) - SRS Control Module (SRSCM)

The SRSCM continually monitors all elements while the ignition is "ON" to determine if a frontal or near-frontal impact is severe enough to require airbag deployment.

FEATURES OF YOUR HYUNDAI

31

Passanger's Airbag

B240B03L

B240B01GK

A fully inflated airbag in combination with a properly worn seat belt slows the driver's or the passenger's forward motion, thus reducing the risk of head and chest injury.

After complete inflation, the airbag immediately starts deflating, enabling the driver to maintain forward visibility.

CAUTION:

Do not install or place any accessories (drink holder, cassette holder, sticker, etc) on the front passenger's panel above the glove box in a vehicle with a passenger's air bag. Such objects may become dangerous projectiles and cause injury if the passenger's air bag inflates.

The SRS service reminder indicator (SRI) on the instrument panel will illuminate for about 6
seconds after the ignition key is turned to the "ON" position or after the engine is started, after which the SRI should go out.

B240B02L

The airbag modules are located both in the center of the steering wheel and in the front passenger's panel above the glove box. When the SRSCM detects a considerable impact to the front of the vehicle, it will automatically deploy the airbags.

Upon deployment, tear seams molded directly into the pad covers will separate under pres- sure from the expansion of the airbags. Further opening of the covers then allows full inflation of the airbags.

1FEATURES OF YOUR HYUNDAI 32

CAUTION:

When installing a container of liquid air freshener inside a vehicle, do not place it near the instrument cluster nor on the in- strument panel pad surface. If there is any leakage from the air freshener onto these areas (instrument cluster, instrument panel pad or air ventilator), it may damage these parts. If the liquid from the air freshener does leak onto these areas, wash them with water immediately.

Passanger's Airbag

B240B05L

B990B05Y-AAT Side Impact Airbag (If installed)

B990B02Y Your Hyundai is equipped with a side impact airbag in each front seat. The purpose of the airbag is to provide the vehicle's driver and/or the front passenger with additional protection than that offered by the seat belt alone. The side impact airbags are designed to deploy only during certain side-impact collisions, depend- ing on the crash severity, angle, speed and point of impact. The side impact airbags are not designed to deploy in all side impact situations.

WARNING:

o If an airbag deploys, there may be a loud noise followed by a fine dust released in the vehicle. These conditions are nor- mal and are not hazardous - the airbags are packed in this fine powder. The dust generated during airbag deployment may cause skin or eye irritation as well as aggravate asthma for some persons. Always wash all exposed skin areas thor- oughly with lukewarm water and a mild soap after an accident in which the airbags were deployed.

o The SRS can function only when the ignition key is in the "ON" position. If the SRS SRI does not illuminute, or contin- uously remains on after illuminating for about 6 seconds when the ignition key is turned to the "ON" position, or after the engine is started, illuminates while driving, the SRS is not working properly. If this occurs, have your vehicle immedi- ately inspected by your Hyundai dealer. o Before you replace a fuse or disconnect a battery terminal, turn the ignition key to the "LOCK" position or remove the ignition key. Never remove or replace the air bag related fuse(s) when the ignition key is in the "ON" position. Failure to heed this warning will cause the SRS SRI to illuminate.

FEATURES OF YOUR HYUNDAI

33

B240C04A-AAT SRS Care

o The SRS is virtually maintenance free and there are no parts you can safely service by yourself. If the SRS SRI (Service Reminder Indicator) does not illuminate, or continu- ously remains on, have your vehicle imme- diately inspected by your Hyundai dealer. o Any work on the SRS system, such as removing, installing, repairing, or any work on the steering wheel must be performed by a qualified Hyundai technician. Improper handling of the airbag system may result in serious personal injury.

WARNING:

o Do not install any accessories on the

side or near the side impact airbag.

o Do not place any objects over the airbag

or between the airbag and yourself.

o Do not place any objects (an umbrella, bag, etc.) between the front door and the front seat. Such objects may become dangerous projectiles and cause injury if the supplemental side impact airbag inflates.

o To prevent unexpected deployment of the side impact airbag that may result in personal injury,avoid impact to the side airbag sensor when the ignition key is on.

WARNING:

o The side impact airbag is supplemental to the driver's and the passenger's seat belt systems and is not a substitute for them. Therefore your seat belts must be worn at all times while the vehicle is in motion. The airbags deploy only in cer- tain side impact conditions severe enough to cause significant injury to the vehicle occupants.

o For best protection from the side impact airbag system and to avoid being injured by the deploying side impact airbag, both front seat occupants should sit in an upright position with the seat belt properly fastened. The driver's hands should be placed on the steering wheel at the 9:00 and 3:00 o'clock positions. The passenger's arms and hands should be placed on their laps.

o Do not use any accessory seat covers. o Use of seat covers could prevent or reduce the effectiveness of the system.

!

WARNING:

o If your car was flooded and has soaked carpeting or water on the floor, you shouldn't try to start the engine; have the car towed to an authorized Hyundai dealer.

1FEATURES OF YOUR HYUNDAI 34

WARNING:

o For cleaning the airbag pad covers, use only a soft, dry cloth or one which has been moistened with plain water. Sol- vents or cleaners could adversely affect the airbag covers and proper deploy- ment of the system.

o No objects should be placed over or near the airbag modules on the steering wheel, instrument panel, and the front passenger’s panel above the glove box, because any such object could cause harm if the vehicle is in a crash severe enough to cause the airbags to inflate. o If the airbags inflate, they must be re- placed by an authorized Hyundai dealer. o Do not tamper with or disconnect SRS wiring, or other components of the SRS system. Doing so could result in injury, due to accidental inflation of the airbags or by rendering the SRS inoperative.

o If components of the airbag system must be discarded, or if the vehicle must be scrapped, certain safety precautions must be observed. Your Hyundai dealer knows these precautions and can give you the necessary information. Failure to follow these precautions and proce- dures could increase the risk of personal injury.

B240C01HP

WARNING:

o Do not install a child restraint system in the front passenger seat position. A child restraint system must never be placed in the front seat. The infant or child could be severely injured or killed by an airbag deployment in case of an accident.

o Modification to SRS components or wir- ing, including the addition of any kind of badges to the pad covers or modifica- tions to the body structure, can ad- versely affect SRS performance and lead to possible injury.

B240D02JM-AAT Additional Safety Precautions o Never let passengers ride in the cargo area (trunk) or on top of a folded-down back seat. All occupants should sit upright, fully back in their seats with their seat belts on and their feet on the floor.

o Passengers should not move out of or change seats while the vehicle is mov- ing. A passenger who is not wearing a seat belt during a crash or emergency stop can be thrown against the inside of the vehicle, against other occupants, or out of the ve- hicle.

o Each seat belt is designed to restrain one occupant. If more than one person uses the same seat belt, they could be seriously injured or killed in a collision.

o Do not use any accessories on seat belts. Devices claiming to improve occu- pant comfort or reposition the seat belt can reduce the protection provided by the seat belt and increase the chance of serious injury in a crash.

o Passengers should not place hard or sharp objects between themselves and the airbags. Carrying hard or sharp objects on your lap or in your mouth can result in injuries if an airbag inflates.

o Keep occupants away from the airbag covers. All occupants should sit upright, fully back in their seats with their seat belts on and their feet on the floor. If occupants are too close to the airbag covers, they could be injured if the airbags inflate.

o Do not attach or place objects on or near the airbag covers. Any object attached to or placed on the front or side impact airbag covers could interfere with the proper opera- tion of the airbags.

o Do not modify the front seats. Modifica- tion of the front seats could interfere with the operation of the supplemental restraint sys- tem sensing components or side impact airbags.

o Do not place items under the front seats. Placing items under the front seats could interfere with the operation of the supple- mental restraint system sensing compo- nents and wiring harnesses.

o Never hold an infant or child on your lap. The infant or child could be seriously injured or killed in the event of a crash. All infants and children should be properly restrained in appropriate child safety seats or seat belts in the rear seat.

FEATURES OF YOUR HYUNDAI

35

WARNING:

o Sitting improperly or out of position can cause occupants to be shifted too close to a deploying airbag, strike the interior structure or be thrown from the vehicle resulting in serious injury or death.

o Always sit upright with the seatback in an upright position, centered on the seat cushion with your seat belt on, legs comfortably extended and your feet on the floor.

Adding Equipment to or Modifying Your Airbag-Equipped Vehicle.

If you modify your vehicle by changing your vehicle's frame, bumper system, front end or side sheet metal or ride height, this may affect the operation of your vehicle's airbag system.

1FEATURES OF YOUR HYUNDAI 36

INSTRUMENT CLUSTER AND INDICATOR LIGHTS

B260A02GK-AAT

B260A02GK-A

FEATURES OF YOUR HYUNDAI

37

1. Speedometer 2. Turn Signal Indicator Light 3. Odometer 4. Automatic Transaxle Position Indicator Light (If installed) 5. Coolant Temperature Gauge 6. Trip odometer 7. Fuel Gauge 8. Tachometer 9. Electronic Stability Program (ESP) Indicator Light (If installed) 10. Trip Odometer Reset Knob 11. Charging System Warning Light 12. Supplemental Restraint System (SRS) Service Reminder

Indicator (SRI)

13. Seat Belt Warning Light 14. High Beam Indicator Light 15. Low Oil Pressure Warning Light 16. Malfunction Indicator Light (MIL) 17. Low Fuel Warning Light 18. Parking Brake/Low Brake Fluid Level Warning Light 19. CRUISE Indicator Light (If installed) 20. CRUISE SET Indicator Light (If installed) 21. Tail Gate Open Warning Light 22. Door Ajar Warning Light 23. ABS Service Reminder Indicator (SRI) (If installed)

1FEATURES OF YOUR HYUNDAI 38

WARNING AND INDICATOR LIGHTS

B260D01A-AAT

Turn Signal Indicator Lights

The blinking green arrows on the instrument panel show the direction indicated by the turn signals. If the arrow comes on but does not blink, blinks more rapidly than normal, or does not illuminate at all, a malfunction in the turn signal system is indicated. Your dealer should be consulted for repairs.

WARNING:

If the both ABS SRI and Parking Brake/ Brake fluid level warning lights remain "ON" or come on while driving, there may be a problem with E.B.D (Electronic Brake Force Distribution). If this occurs, avoid sudden stops and have your vehicle checked by your Hyundai dealer as soon as possible.

B260P02Y-GAT

ABS Service Reminder Indica- tor (SRI) (If Installed)

B260F01A-AAT

High Beam Indicator Light

The high beam indicator light comes on when- ever the headlights are switched to the high beam or flash position.

When the key is turned to the "ON" position, the Anti-Lock Brake System SRI will come on and then go off in a few seconds. If the ABS SRI remains on, comes on while driving, or does not come on when the key is turned to the "ON" position, this indicates that there may be a problem with the ABS. If this occurs, have your vehicle checked by your Hyundai dealer as soon as possible. The normal braking system will still be operational, but without the assistance of the anti-lock brake system.

B260G01A-AAT

Low Oil Pressure Warning Light

CAUTION:

If the oil pressure warning light stays on while the engine is running, serious engine damage may result. The oil pressure warn- ing light comes on whenever there is insuf- ficient oil pressure. In normal operation, it should come on when the ignition switch is turned on, then go out when the engine is started. If the oil pressure warning light stays on while the engine is running, there is a serious malfunction. If this happens, stop the car as soon as it is safe to do so, turn off the engine and check the oil level. If the oil level is low, fill the engine oil to the proper level and start the engine again. If the light stays on with the engine running, turn the engine off imme- diately. In any instance where the oil light stays on when the engine is running, the engine should be checked by a Hyundai dealer before the car is driven again.

FEATURES OF YOUR HYUNDAI

39

B260J01A-AAT

Charging System Warning Light

The charging system warning light should come on when the ignition is turned on, then go out when the engine is running. If the light stays on while the engine is running, there is a malfunc- tion in the electrical charging system. If the light comes on while you are driving, stop, turn off the engine and check under the hood. First, make certain the generator drive belt is in place. If it is, check the tension of the belt. Do this as shown on page 6-23 by pushing down on the center of the belt. Have the system checked by your Hyundai dealer as soon as possible.

The brake fluid level warning light indicates that the brake fluid level in the brake master cylinder is low and hydraulic brake fluid conforming to DOT 3 or DOT 4 specifications should be added. After adding fluid, if no other trouble is found, the car should be immediately and care- fully driven to a Hyundai dealer for inspection. If further trouble is experienced, the vehicle should not be driven at all but taken to a dealer by a professional towing service. Your Hyundai is equipped with dual-diagonal braking systems. This means you still have braking on two wheels even if one of the dual systems should fail. With only one of the dual systems working, more than normal pedal travel and greater pedal pressure are required to stop the car. Also, the car will not stop in as short a distance with only half of the brake system working. If the brakes fail while you are driving, shift to a lower gear for additional engine braking and stop the car as soon as it is safe to do so.

B260H01GK-AAT

Parking Brake/Low Brake Fluid Level Warning Light

CAUITON:

If you suspect brake trouble, have your brakes checked by a Hyundai dealer as soon as possible. Driving your car with a problem in either the brake electrical sys- tem or brake hydraulic system is danger- ous, and could result in a serious injury or death.

Warning Light Operation

The parking brake/low brake fluid level warning light should come on when the parking brake is applied and the ignition switch is turned to "ON" or "START". After the engine is started, the light should go out in three seconds. If the parking brake is not applied, the warning light should come on when the ignition switch is turned to "ON" or "START", then go out in three seconds. If the light comes on at any other time, you should slow the vehicle and bring it to a complete stop in a safe location off the roadway.

1FEATURES OF YOUR HYUNDAI 40

B260L02HP-GAT

B260K01F-AAT

B260N02A-AAT

Door Ajar Warning Light and Chime (If Installed)

The door ajar warning light warns you that a door is not completely closed and the chime warns you that the key is in the ignition switch. NOTE : The warning chime only sounds whenever the key is in the ignition switch and the driver's side front door is open simulta- neously. The chime sounds until the key is removed from the ignition switch or the driver's side front door is closed.

B260M01A-AAT

Low Fuel Level Warning Light

The low fuel level warning light comes on when the fuel tank is approaching empty. When it comes on, you should add fuel as soon as possible. Driving with the fuel level warning light on or with the fuel level below "E" can cause the engine to misfire and damage the catalytic converter.

Tail Gate Open Warning Light

This light remains on unless the tail gate is completely closed and latched.

B260B01JM-AAT

SRS (Airbag) Service Reminder Indicator (SRI)

The SRS service reminder indicator (SRI) comes on for about 6 seconds after the ignition key is turned to the "ON" position or after the engine is started, after which it will go out.

This light also comes on when the SRS is not working properly. If the SRI does not come on, or continuously remains on after coming on for about 6 seconds when you turned the ignition key to the "ON" position or started the engine, or if it comes on while driving, have the SRS inspected by an authorized Hyundai Dealer.

Malfunction Indicator Light

This light illuminates when there is a malfunction of an exhaust gas related component, and the system is not functioning properly so that the exhaust gas regulation values are not satisfied. This light will also illuminate when the ignition key is turned to the "ON" position, and then it will go out in a few seconds after the engine is started. If it illuminates while driving, or does not illumi- nate when the ignition key is turned to the "ON" position, take your car to your nearest autho- rized Hyundai dealer and have the system checked.

B260E01L-AAT

Seat Belt Reminder Light And Chime

Seat belt reminder light comes and stays on until the seat belt is fastened when the ignition key is turned "ON" or "START". And, the warning chime will also sound for about 6 seconds.

FEATURES OF YOUR HYUNDAI

41

B270A01A-AAT BRAKE PAD WEAR WARNING SOUND

The front disc brake pads have wear indicators that should make a high-pitched squealing or scraping noise when new pads are needed. The sound may come and go or be heard all the time when the vehicle is moving. It may also be heard when the brake pedal is pushed down firmly. Excessive rotor damage will result if the worn pads are not replaced. See your Hyundai dealer immediately.

B260Q01E-GAT

B265C01LZ-AAT

CRUISE Indicator Light (If Installed)

The cruise indicator light in the instrument clus- ter is illuminated when the cruise control main switch on the end of the barrel is pushed. The indicator light does not illuminate when the cruise control main switch is pushed a second time. Information about the use of cruise control is beginning on page 1-63.

B260R01E-GAT

CRUISE SET Indicator Light (If installed)

The set indicator light in the instrument cluster is illuminated when the cruise control switch is pushed downward to "SET (COAST)". The set indicator light does not illuminate when the control switch is in the "CANCEL" position.

Electronic Stability Program Indicator Lights (If installed)

The electronic stability program indicators change operation according to the ignition switch position and whether the system is in operation or not. They will illuminate when the ignition key is turned to the "ON" position, but should go out after three seconds. If the ESP or ESP-OFF indicator stays on, take your car to your autho- rized Hyundai dealer and have the system checked. See section 2 for more information about the ESP.

1FEATURES OF YOUR HYUNDAI 42

INSTRUMENT CLUSTER

B280A01A-AAT FUEL GAUGE

B290A02A-AAT ENGINE COOLANT TEMPERATURE GAUGE

The needle on the gauge indicates the approxi- mate fuel level in the fuel tank. The fuel capacity is given in Section 9.

HGK2059

HGK2060

WARNING:

Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could erupt and cause severe burns. Wait until the engine is cool before removing the radiator cap.

The needle on the engine coolant temperature gauge should stay in the normal range. If it moves across the dial to "H" (Hot), pull over and stop as soon as possible and turn off the engine. Then open the hood and after the engine has cooled, check the coolant level and the water pump drive belt. If you suspect cooling system trouble, have your cooling system checked by a Hyundai dealer as soon as possible.

B300A01A-AAT SPEEDOMETER

HGK2058A Your Hyundai's speedometer is calibrated in miles per hour (on the outer scale) and kilome- ters per hour (on the inner scale).

B330A03E-AAT TACHOMETER

B310B01GK-AAT Odometer/Trip odometer Type A

Type A

FEATURES OF YOUR HYUNDAI

43

Type B

HGK028B Function of digital odometer/trip odom- eter Pushing in the reset switch on the right side of speedometer when the ignition switch is turned "ON" will display the following sequence:

Type B

HGK2061-1

HGK055C

The tachometer registers the speed of your engine in revolutions per minute (rpm).

B330A01GK

CAUTION:

The engine should not be raced to such a speed that the needle enters the red zone on the tachometer face. This can cause severe engine damage and may void your warranty.

1FEATURES OF YOUR HYUNDAI 44

1. Odometer

The odometer records the total driving distance in miles, and is useful for keeping a record for maintenance intervals.

NOTE: Any alteration of the odometer may void your warranty coverage.

2,3 Trip odometer

Records the distance of 2 trips in miles. TRIP A: Distance you have traveled from your origination point to a first destination. TRIP B: Distance from the first destination to the final destination.

To shift from TRIP A to TRIP B, press the reset switch. When pressed for 1 second, it will reset to 0.

TRIP COMPUTER

B400B02GK-GAT (If installed)

Type A

Type B

B400B01GK-E

The trip computer is a microcomputer-con-