2010 Hyundai Sonata Owners Manual

Heating and Cooling Controls

ONF048082L

1. Driver's temperature control button 2. Fan speed control button 3. AUTO (automatic control) button 4. Dual temperature control selection but-

ton

5. OFF button 6. Air conditioning button

7. Air intake control button 8. Front wiper defrost button 9. Rear window defrost button 10. Mode selection button 11. Passenger's temperature control but-

ton

12. A/C display

B970C02NF-AAT

Automatic Operation

FEATURES OF YOUR HYUNDAI

105105

ONF048083N

The FATC (Full Automatic Temperature Control) system automatically controls heating and cooling as follows:

1. Push the "AUTO" switch. The indicator light will illuminate confirming that the Face, Floor and/or Bi-Level modes as well as the blower speed and air conditioner will be controlled automatically. And, the air conditioning will operate if ambient temperature is higher than 35°F(1.5°C) and automatically turns off if the ambient temperature drops below 33°F(0.6°C).

ONF048086
2. Push the "TEMP" button to set the de-

sired temperature. The temperature will increase to the maximum "HI" by pushing the up button. The temperature will decrease to the minimum "LO" by pushing the down button.

ONF048087

Adjusting the driver and passenger side temperature individually 1. Press the DUAL button to operate the driver and passenger side temperature individually. Pressing the right temperature control button will automatically switch to the DUAL mode as well.

2. Press the left temperature control to adjust the driver side temperature. Press the right temperature control to adjust the passenger side temperature.

When the driver side temperature is set to the highest (HI) or lowest (LO) temperature setting, the DUAL mode is deactivated for maximum heating or cooling.

1FEATURES OF YOUR HYUNDAI 106

Adjusting the driver and passenger side temperature equally 1. Press the DUAL button again to deactivate DUAL mode. The passenger side temperature will be set to the same as the driver side temperature.

2. Press the left temperature control button. The driver and passenger side temperature will be adjusted equally.

Temperature conversion If the battery has been discharged or dis- connected, the temperature mode display will reset to Fahrenheit. This is normal condition. You can switch the temperature mode between Fahrenheit to Centigrade as follows; While depressing the DUAL button, de- press the MODE button for 3 seconds or more. The display will change from Fahr- enheit to Centigrade, or from Centigrade to Fahrenheit.

B980A01Y-AAT

MANUAL OPERATION The heating and cooling system can be controlled manually as well by pushing buttons other than the "AUTO" button. In this state, the system sequentially works according to the order of buttons selected. The function of the buttons which are not selected will be controlled automatically. Press the "AUTO" button in order to convert to automatic control of the system.

ONF048115

NOTE: Never place anything over the sensor which is located on the instrument panel to ensure better control of the heating and cooling system.

B980B01NF-GAT

Fan Speed Control

B670C03Y-AAT

Air Intake Control Switch

FEATURES OF YOUR HYUNDAI

107107

FRESH MODE

The indicator light on the button goes on when the air intake control is in fresh mode.

ONF048089N

The fan speed can be set to the desired speed by pressing the fan speed control button. The higher the fan speed is, the more air is delivered. Pressing the "OFF" button turns off the fan.

ONF048088
This is used to select fresh outside air or recirculation of inside air. To change the air intake control mode (Fresh mode, Recirculation mode), push the control button.

RECIRCULATION MODE

The indicator light on the button is illuminated when the air intake control is in recirculation mode. With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according function selected.

the

to

With the "Recirculation" mode selected, air from within the passenger compart- ment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: It should be noted that prolonged opera- tion of the heating system in "recircula- tion" mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Recircu- lation" mode selected may result in the air within the passenger compartment becoming excessively dry.

1FEATURES OF YOUR HYUNDAI 108

B980D01Y-AAT

Heating and Cooling System Off

B980E01NF-GAT

Air Flow Control

Press the "OFF" button to stop the operation of the heating and cooling system.

ONF048091

ONF048084N This is used to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Four symbols are used to represent Face, Bi-Level, Floor, Floor- Defrost position.

Face-Level (B, D) *1

When selecting the "Face-Level" mode, the indicator light will come on, causing air to be discharged through the face level vents.

Bi-Level (B, D, C, E) *1

When selecting the "Bi-Level", the indica- tor light will come on and the air will be discharged through the face vents and the floor vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.

Floor-Level (C, E, A, D) *1

When selecting the "Floor-Level", the indi- cator light will come on and the air will be discharged through the floor vents, windsheld defroster nozzle, side defroster nozzle and side ventilator.

Floor-Defrost Level (A, C, E, D) *1

When selecting the "Floor-Defrost" mode, the indicator light will come on and the air will be discharged through the windshield defroster nozzle, the floor vents, side defroster nozzle and side ventilator. If any of the temperature control switch, the blower fan control switch, or the defrost switch is selected in "Floor-Defrost" mode, the A/C will turn on automatically and "Fresh" mode will be activated.

*1 : See page 1-97

B980F01NF-AAT

Defrost Switch Type A

Type B

FEATURES OF YOUR HYUNDAI

109109

B760A01NF-AAT

Climate Control Air Filter (For Evapo- rator And Blower Unit) (If Installed)

Outside air

Inside of a vehicle

ONF048071N

Blower

Evaporator core

Filter

Inside air HNF2181

The climate control air filter is located in the right side of the instrument panel. It operates to decrease the amount of pol- lutants entering the car. To replace the climate control air filter, refer to page 6-19.

ONF048072
When the "Defrost" button is pressed, the fresh mode will be automatically selected and the air will be discharged through the windshield defroster nozzle, side defroster nozzle and side ventilator. To assist in defrosting, the air conditioning will oper- ate if ambient temperature is higher than 35°F(1.5°C) and automatically turns off if the ambient temperature drops below 33°F(0.6°C).

1FEATURES OF YOUR HYUNDAI 110

CAUTION:

o Replace the filter every 10,000 miles

(15,000 km) or once a year. If the car is being driven in severe conditions such as dusty, rough roads, more frequent climate control air filter inspections and changes are re- quired.

o When the air flow rate is suddenly decreased, the system should be checked at an authorized dealer.

ANTENNA

B870D01Y-AAT

Glass Antenna

HNF2189-A

When the radio power switch is turned on while the ignition key is in either the "ON" or "ACC" position, your car will receive both AM and FM broadcast signals through the antenna in the rear window glass.

CAUTION:

o Do not clean the inner side of the rear window glass with an abrasive type of glass cleaner or use a scraper to remove foreign deposits from the inner surface of the glass as this may cause damage to the antenna elements.

o Avoid adding metallic coatings to the rear window glass, such as Ni, Cd, etc. These can disturb receiving AM and FM broadcast signals.

B880A01NF-AAT

Satellite Antenna

D281400AFD

Aux, USB and iPod® (if installed) Type A

ONF048133N

ONF048111

Type B

The satellite antenna is installed on the roof of your car to listen to a satellite radio broadcast. This antenna is permanently attached and can not be removed

NOTE: In places such as tunnels, the satellite broadcast signal is not available.

* iPod® is a trademark of Apple Inc.

ONF048112

FEATURES OF YOUR HYUNDAI

111111

NOTE: When using a portable audio device con- nected to the power outlet, noise may occur during playback. If this happens, use the power source of the portable audio device.

B875D01TG-AAT

AVN (AUDIO, VIDEO AND NAVIGA- TION) System (If Installed) If your vehicle has an AVN, you can refer to the AVN operation manual provided with AVN for the detailed function.

! CAUTION:

This vehicle may include mercury-con- taining devices installed by the manu- facturer: * High Intensity Discharge Headlamps * Navigation Display * Back-lit Instruments Remove Devices Before Vehicle dis- posal Upon Removal of Devices: Please Reuse, Recycle, or Dispose as Hazardous Waste

1FEATURES OF YOUR HYUNDAI 112

STEREO SOUND SYSTEM

B750A02A-AAT

How Car Audio Works FM reception

Ionosphere

AM reception

Ionosphere

FM radio station

Mountains

Buildings

B750A02L AM broadcasts can be received at greater distances than FM broadcasts. This is because AM radio waves are transmitted at low frequencies. These long, low frequency radio waves can follow the curvature of the earth rather than travelling straight out into the atmosphere. In addition, they curve around obstructions so that they can provide better signal coverage.

B750A01L AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures the best possible quality reproduction. However, in some cases the signal coming to your vehicle may not be strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.

Unobstructed area

Iron bridges

Obstructed area

B750A03L FM broadcasts are transmitted at high fre- quencies and do not bend to follow the earth's surface. Because of this, FM broad- casts generally begin to fade at short distances from the station. Also, FM signals are easily affected by buildings, mountains, or other obstructions. These can result in certain listening conditions which might lead you to believe a problem exists with your radio. The following conditions are normal and do not indicate radio trouble:

FEATURES OF YOUR HYUNDAI

113113

B750B05Y-AAT

Using a cellular phone or a two-way radio When a cellular phone is used inside the vehicle, noise may be produced from the audio equipment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.

WARNING:

Hyundai recommends that you never use a cell phone while driving. This could result in loss of control, and an accident that may cause death, serious injury, or property damage. You must stop at a safe place to use a cellular phone.

NOTE: Some states and cities have regulations prohibiting the use of cell phones while driving. You should be aware of the specific requirements in your area.

B750A04L o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another stronger station.

o Flutter/Static - Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.

B750A05L o Station Swapping - As an FM signal weakens, another more powerful sig- nal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.

o Multi-Path Cancellation - Radio signals being received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this occurs, select another station until the condition has passed.

1FEATURES OF YOUR HYUNDAI CARE OF DISCS 114

B850A02F-AAT

Proper Handling

Keep Your Discs Clean

Damaged Disc Do not attempt to play damaged, warped or cracked discs. These could severely damage the playback mechanism.

Storage When not in use, place your discs in their individual case and store them in a cool place away from the sun, heat, and dust. Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism.

B850A01L Handle your disc as shown. Do not drop the disc. Hold the disc so you will not leave fingerprints on the surface. If the surface is scratched, it may cause the pickup to skip signal tracks. Do not affix tape, paper, or gummed labels on the disc. Do not write on the disc.

B850A02L Fingerprints, dust, or soil on the surface of a disc could cause the pickup to skip signal tracks. Wipe the surface clean with a clean soft cloth. If the surface is heavily soiled, dampen a clean soft cloth in a solution of mild neutral detergent to wipe it clean. See drawing.

AUDIO SYSTEM

PA710SA01NF-AAT

RADIO, SET UP, VOLUME CONTROL (PA710S) (If Installed)

FEATURES OF YOUR HYUNDAI

115

1. FM Selection Button 2. AM Selection Button 3. XM Selection Button 4. CD/AUX Selection Button 5. Automatic Channel Selection Button 6. Power ON/OFF 7. SCAN Button 8. MUTE Button 9. Information Display Button 10. SET UP Button 11. TUNE/ENTER Button 12. CAT(FLDR) Button 13. Pre-set Button

10

12

11

13

NFF_USA_CDP_RADIO

1FEATURES OF YOUR HYUNDAI 116

PA710SB01NF-AAT

1. FM Selection Button Turns to FM mode and toggles FM1 and FM2 when the button is pressed each time.

2. AM Selection Button Turns to AM mode, selects the AM.

3. XM Selection Button Turns to XM mode, and toggles in the order of XM1➟XM2➟XM3➟···➟XM1··· when the button is pressed each time.

4. CD/AUX Selection Button If there is a CD in the CDP DECK it turns to CD mode, and if a device is connected to AUX then it toggles. CD➟AUX➟CD··· when the button is pressed each time.(It will not turn to AUX if the auxiliary device is not connected)

5. Automatic Channel Selection

Button

8. MUTE Button Press to temporarily cut off the Sound.

o When the [SEEK

]button is pressed, it reduces the band frequency by 200khz to automatically select channel. Stops at the previous frequency if no channel is found.

o When the [SEEK

]button is pressed, it increases the band frequency by 200khz to automatically select chan- nel. Stops at the previous frequency if no channel is found.

6. Power ON/OFF & Volume Control

Button

Turns the set on/off when the IGNITION SWITCH is on ACC or ON. If the button is turned to the right, it increases the volume and left, decreases the volume.

7. SCAN Button If this button is pressed, the frequencies will increase and receive the correspond- ing broadcasts. This function will play the frequencies for 5 seconds (XM mode : 10 seconds) each and find other broadcasts as the frequency increases. Press the button again when desiring to continue listening to the currently playing broadcast.

9. Information Display Button Information Display function operation (In- formation is displayed each time (the) Key is pressed) : Pressing the Category/ Channel➟ Name/Song Title➟Category/Channel... for 3 seconds will display the corresponding text then become restored.

Artist

Text Scroll operation After pressing (the) Key, if the text to be displayed is longer than the LCD text line, then rotating the Tune Knob will operate the Page up function displaying 16(Max. characters) characters for 3 seconds each dispalys.

10. SET UP Button Press this button to turn to the XM option, TEXT SCROLL, AVC and adjustment mode. If no action is taken for 5 seconds after pressing the button, it will return to the play mode.(After entering SET UP mode, move between items using the left, right and PUSH functions of the TUNE button.) The set up item changes from TEXT SCROLL ➟AVC➟XM...

11. TUNE/ENTER Button Turn this button clockwise by one notch to increase frequency by 200Khz from cur- rent frequency. Turn this button counterclockwise by one notch to decrease frequency by 200Khz from current frequency.

Press this button while holding SET UP button to activate / inactivate the item. Select SET UP item using left and right function of the Tune button.

Pressing the button changes the BASS, MIDDLE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Au- dio control knob clockwise or counter- clockwise.

o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.

o MIDDLE Control To increase the MIDDLE, rotate the knob clockwise, while to decrease the MIDDLE, rotate the knob counterclockwise.

o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.

o FADER Control Turn the control knob clockwise to empha- size rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).

o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

] button when Category Up

12. CAT(FLDR) Button Moves [CAT search operation. o Category is moved Up from the cat- egory currently being received and Category Name becomes displayed. o If the Enter Key is not pressed within 5
seconds, then the previous mode will be restored.

FEATURES OF YOUR HYUNDAI

117

o If the Key is pressed while in the last Category, then the first category will become displayed and operation will be repeated.

o Corresponding category can be se-

lected by pressing ENTER.

] button when Category

Moves [CAT Down search operation. o Category is moved Down from the cat- egory currently being received and Category Name becomes displayed. o If the Enter Key is not pressed within 5
seconds, then the previous mode will be restored. o If the [CAT

] Key is pressed while in the first Category, then the last category will become displayed and operation will be repeated.

o Corresponding category can be se-

lected by pressing ENTER.

13. Pre-set Button Push [1]~[6] buttons less than 0.8 seconds to play the channel saved in each button. Push pre-set button for 0.8 seconds or longer to save current channel to the re- spective button with a beep.

1FEATURES OF YOUR HYUNDAI 118

PA710SC01NF-AAT

CD (PA710S) (If Installed)

11
10

1. CD loading slot 2. CD indicator 3. CD Eject Button 4. CD/AUX Selection Button 5. Automatic Track Selection Button 6. INFO Button 7. TUNE/ENTER Button 8. REPEAT Button 9. RANDOM Play Button 10. SCAN Play Button 11. MUTE Button

NFF_USA_CDP_CD

PA710SD01NF-AAT

1. CD loading slot Please face printed side upward and gen- tly push in. When the ignition switch is on ACC or ON and power is off, power is automatically turned on if the CD is loaded. This CDP supports 12 cm CD. But if VCD, Data CD are loaded, "Reading error" mes- sage will appear and CD will be ejected.

2. CD Indicator When car ignition switch is ACC or ON and if the CD is loaded, this indicator is lighted. If the CD is ejected the light is turned off.

3. CD eject Button Push button to eject the CD during CD playback. This button is enabled when ignition switch is off.

4. CD/AUX Selection Button If the auxiliary device is connected, it turns to AUX MODE to play the sound from the auxiliary player. If no Disc and auxiliary device is con- nected, it displays "NO Media" for 5 sec- onds and returns to the previous mode.

5. Automatic Track Selection Button o Push [SEEK ] button for less than 0.8
seconds to play from the beginning of current song. o Push [SEEK

] button for less than 0.8
seconds and press again within 1 sec- onds to play the previous song.

o Push [SEEK

] button for 0.8 or longer to initiate reverse direction high speed sound search of current song.

o Push [SEEK

] button for less than 0.8

seconds to play the next song.

o Push [SEEK

] button for 0.8 or longer to initiate high speed sound search of current song.

6. INFO Button Displays the information of the current CD TRACK in the order of DISC TITLE➟ DISC ARTIST➟TRACK TITLE➟ TRACK ARTIST➟ TOTAL TRACK➟ Play Screen➟ DISC TITLE ➟···.(not displayed if the infor- mation is not available on the DISC.)

FEATURES OF YOUR HYUNDAI

119

7. TUNE/ENTER Button Turn this button clockwise to display songs after current song. Also, turn this button counterclockwise to display songs before current song. To listen to the displayed song, press the button to skip to the song and play.

Pressing the button changes the BASS, MIDDLE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Au- dio control knob clockwise or counter- clockwise.

o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.

o MIDDLE Control To increase the MIDDLE, rotate the knob clockwise, while to decrease the MIDDLE, rotate the knob counterclockwise.

o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.

10. SCAN Play Button Plays first 10 seconds of each song in the DISC. To cancel the mode, press the key once again.

11. MUTE Button Press this button to temporarily cut off the Sound. "Audio Mute" is displayed on the LCD. Press the button once again to cancel MUTE mode.

1FEATURES OF YOUR HYUNDAI 120

o FADER Control Turn the control knob clockwise to empha- size rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).

o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

8.REPEAT Button Repeats current song when the button is pressed for less than 0.8 seconds. Repeats the entire DISC when the button is pressed for 0.8 seconds or longer.

9. RANDOM Play Button Turns on/off the randomization of the play list of files in the currently played DISC. To cancel the mode, press the key once again.

PA710SE01NF-AAT

USING USB (PA710S) (If Installed)

FEATURES OF YOUR HYUNDAI

121

1. AUX Selection Button 2. Track moving Button 3. INFO Selection Button 4. Folder moving Button 5. TUNE/ENTER Button 6. Random Playback Button 7. Repeat Selection Button 8. SCAN Selection Button

H_NF_A_U_CDP_USB

1FEATURES OF YOUR HYUNDAI 122

PA710SF01NF-AAT If a USB device is connected to the multiple terminal inside the console on the right hand side of the driver’s seat, the ‘USB’ icon will be displayed on the top right corner of the display screen.

1.AUX Selection Button If USB is connected, it switches to the USB mode from the CD mode to play the song files stored in the USB. If there is no CD and USB mode from the Radio mode, it displays ‘NO MEDIA’.

2. Track Moving Button o Press the [SEEK

] button for less than 0.8 seconds to play from the beginning of the song currently played. Press the button for less than 0.8 sec- onds and press it again within 1 second to move and play the previous track. Press the button for 0.8 seconds or longer to play the song in reverse direc- tion in fast speed. o Press the [SEEK

] button for less than 0.8 seconds to move to the next track. Press the button for 0.8 seconds or longer to play the song in forward direc- tion in fast speed.

3. INFO Button Displays the information of the file cur- rently played in the order of FILE NAME ➟TITLE➟ARTIST➟ALBUM➟FOLDER➟TOTAL FILE➟normal display➟FILE NAME➟… (Displays no information if the file has no song information.)

4. Folder moving Button o Moves [FLDR

] button to the child folder of the current folder and displays the first song in the folder. Press ENT/ TUNE button to move to the folder dis- played. It will play the first song in the folder.

o Moves [FLDR

] button to the parent folder and displays the first song in the folder. Press ENT/TUNE button to move to the folder displayed. It will play the first song in the folder.

5. TUNE/ENTER Button Turn this button clockwise to display the songs next to the currently played song. Turn the button counterclockwise to dis- play the songs before the currently played song. Press the button to skip and play the se- lected song.

Pressing the button changes the BASS, MIDDLE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Au- dio control knob clockwise or counter- clockwise.

o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.

o MIDDLE Control To increase the MIDDLE, rotate the knob clockwise, while to decrease the MIDDLE, rotate the knob counterclockwise.

o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.

o FADER Control Turn the control knob clockwise to empha- size rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).

o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

6. RANDOM Playback Button Press the button for less than 0.8 seconds to start or stop the random playback of the songs in the current folder. Press the button for more than 0.8 seconds to randomly play the entire songs in the USB device. Press the button again to cancel the mode.

7. REPEAT Button Press the button for less than 0.8 seconds to repeat the song currently played. Press the button for more than 0.8 seconds to repeat the entire songs in the USB device.

8. SCAN Button Plays 10 seconds of each song in the USB device. Press the button once again to cancel scanning.

CAUTION IN USING USB DEVICE:

o To use the external USB device, make sure the device is not connected when starting up the vehicle and connect the device after starting up.

o If you start the vehicle when the USB device is connected, it may damage the USB device. (USB is not ESA)

o If the vehicle is started up or turned off while the external USB device is con- nected, the external USB device may not work.

o It may not play all MP3 or WMA files. 1) It can only play MP3 files with the rate between

compression 8Kbps~320Kbps.

2) It can only play WMA music files with the compression rate between 8Kbps~320Kbps.

o Take cautions for static electricity when connecting or disconnecting the external USB device.

o Encoded MP3 PLAYER'S are not rec-

ognizable.

o Depending on the condition of the ex- ternal USB device, the connected external USB device can be unrecog- nizable.

FEATURES OF YOUR HYUNDAI

123

o When the formatted byte/sector set- ting of External USB devices is not either 512BYTE or 2048BYTE, then the device will not be recognized.

o Only the USB device formatted to FAT

12/16/32 can be used.

o USB device without USB

IF (Implementers-Forum) authentica- tion may not be recognizable.

o Make sure the USB connection termi- nal does not come in contact with a human body or any other object.

o If you repeat connecting or discon- necting USB device in a short period of time, it may damage the device.

o You might hear unusual noise when connecting or disconnecting a USB device.

o If you disconnect the external USB device during playback in USB mode, the external USB device can be dam- aged. Therefore, connect the exter- nal USB device when the engine is turned off or in another mode.

o Depending on the type and capacity of the external USB device or the type of the files stored in the device, there is a difference in the time taken for recognition of the device, but this does not indicate a problem.

o Do not use the USB device for other

purposes than playing music files.

1FEATURES OF YOUR HYUNDAI 124

o Use of USB accessories such as a recharger or heater using the USB I/F may lower the performance or cause trouble.

o If you use devices such as a USB hub you purchased separately, the vehicle’s audio system may not rec- ognize the USB device. Connect the USB device directly to the multimedia terminal of the vehicle.

PA710SG01NF-AAT

RUNNING iPod® (PA710S) (If Installed)

FEATURES OF YOUR HYUNDAI

125

1. iPod Selection Button 2. Track moving Button 3. INFO Selection Button 4. Category Selection Button 5. TUNE/ENTER Button 6. RANDOM Playback Button 7. REPEAT Selection Button

* iPod® is a trademark of Apple Inc.

H_NF_A_U_CDP_IPOD

1FEATURES OF YOUR HYUNDAI 126

PA710SH01NF-AAT If the iPod exclusive cable (if installed) is connected to the multiple terminal inside the console on the right hand side of the driver’s seat, the ‘iPod’ icon will be dis- played on the top right corner of the display screen.

1. iPod Selection Button If iPod is connected, it switches to the iPod mode from the CD mode to play the song files stored in the iPod. If there is no CD and AUX mode from the Radio mode, it displays ‘NO MEDIA’.

2. Track Moving Button o Press the [SEEK

] button for less than 0.8 seconds to play from the beginning of the song currently played. Press the button for less than 0.8 sec- onds and press it again within 1 second to move and play the previous track. Press the button for 0.8 seconds or longer to play the song in reverse direc- tion in fast speed. o Press the [SEEK

] button for less than 0.8 seconds to move to the next track. Press the button for 0.8 seconds or longer to play the song in forward direc- tion in fast speed.

3. INFO Button Displays the information of the file cur- rently played in the order of FILE NAME ➟TITLE➟ARTIST➟ALBUM➟normal dis- play ➟FILE NAME➟…. (Displays no information if the file has no song information.)

4. Category Selection Button Moves to the upper category from currently played category of the iPod. To move to (play) the category (song) displayed, press MENU(Preset6). You will be able to search through the lower category of the selected category. The order of iPod’s category is SONG, ALBUMS, ARTISTS, GENRES, and iPod.

5. TUNE/ENTER Button When you turn the button clockwise, it will display the songs (category) next to the song currently played (category in the same level). Also, when you turn the button counter- clockwise, it will display the songs (cat- egory) before the song currently played (category in the same level). If you want to listen to the song displayed in the song category, press the button, then it will skip to the selected song and play.

Pressing the button changes the BASS, MIDDLE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Au- dio control knob clockwise or counter- clockwise.

o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.

o MIDDLE Control To increase the MIDDLE, rotate the knob clockwise, while to decrease the MIDDLE, rotate the knob counterclockwise.

o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.

o FADER Control Turn the control knob clockwise to empha- size rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).

NOTE FOR USING AN iPod DEVICE: o Some iPod models might not support the communication protocol and the files will not be played. (iPod models supported: Mini, 4G, Photo, Nano, 5G) o The order of search or playback of songs in the iPod can be different from the order searched in the audio system.

o If the iPod crashes due to its own trouble, reset iPod. (Reset: Refer to iPod manual)

o An iPod may not operate normally on

low battery charge.

o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

6. RANDOM Playback Button Press the button for less than 0.8 seconds to activate or deactivate the random play- back of the songs within the current cat- egory. Press the button for longer than 0.8 sec- onds to randomly play all songs in the entire album of the iPod. Press the button once again to cancel the mode.

7. REPEAT Button Repeats the song currently played.

FEATURES OF YOUR HYUNDAI

127

CAUTION IN USING iPod DEVICE:

o You need the power cable exclusive for an iPod in order to operate iPod with the buttons on the audio system. The PC cable provided by Apple may cause a malfunction. Do not use it for vehicle use.

o When connecting the device with an iPod cable, push in the jack fully to not interfere with communication.

o When adjusting the sound of an iPod and the audio system, the sound ef- fects of both devices will overlap each and might reduce or distort the quality of the sound.

o Deactivate (turn off) the equalizer function of an iPod when adjusting the audio system’s volume, and turn off the equalizer of the audio system when using the equalizer of an iPod. o When the iPod cable is connected, the system can be switched to the AUX mode even without the iPod device and can cause noise. Disconnect iPod cable when you are not using the iPod device.

1FEATURES OF YOUR HYUNDAI 128

PA760SA01NF-AAT

RADIO, SET UP, VOLUME CONTROL (PA760S) (If Installed)

1. FM Selection Button 2. AM Selection Button 3. XM Selection Button 4. CD/AUX Selection Button 5. Automatic Channel Selection Button 6. Power ON/OFF 7. SCAN Button 8. MUTE Button 9. Information Display Button 10. SET UP Button 11. TUNE/ENTER Button 12. CAT(FLDR) Button 13. Pre-set Button

10

12

11

13

NFF_USA_CDC_RADIO

PA760SB01NF-AAT

1. FM Selection Button Turns to FM mode and toggles FM1 and FM2 when the button is pressed each time.

2. AM Selection Button Turns to AM mode, selects the AM.

3. XM Selection Button Turns to XM mode, and toggles in the order of XM1➟XM2➟XM3➟···➟XM1··· when the button is pressed each time.

4. CD/AUX Selection Button If there is a CD in the CDP DECK it turns to CD mode, and if a device is connected to AUX then it toggles. CD➟AUX➟CD··· when the button is pressed each time.(It will not turn to AUX if the auxiliary device is not connected)

5. Automatic Channel Selection

Button

o When the [SEEK

]button is pressed, it reduces the band frequency by 200khz to automatically select channel. Stops at the previous frequency if no channel is found.

o When the [SEEK

]button is pressed, it increases the band frequency by 200khz to automatically select chan- nel.

Stops at the previous frequency if no chan- nel is found.

6. Power ON/OFF & Volume Control

Button

Turns the set on/off when the IGNITION SWITCH is on ACC or ON. If the button is turned to the right, it increases the volume and left, decreases the volume.

7. SCAN Button If this button is pressed, the frequencies will increase and receive the correspond- ing broadcasts. This function will play the frequencies for 5 seconds (XM mode : 10 seconds) each and find other broadcasts as the frequency increases. Press the button again when desiring to continue listening to the currently playing broadcast.

8. MUTE Button Press to temporarily cut off the Sound.

FEATURES OF YOUR HYUNDAI

129

9. Information Display Button Information Display function operation (In- formation is displayed each time (the) Key is pressed) : Pressing the Category/ Channel➟ Name/Song Title➟Category/Channel... for 3 seconds will display the corresponding text then become restored.

Artist

Text Scroll operation After pressing (the) Key, if the text to be displayed is longer than the LCD text line, then rotating the Tune Knob will operate the Page up function displaying 16(Max. characters) characters for 3 seconds each dispalys.

10. SET UP Button Press this button to turn to the XM option, TEXT SCROLL, AVC and adjustment mode. If no action is taken for 5 seconds after pressing the button, it will return to the play mode.(After entering SET UP mode, move between items using the left, right and PUSH functions of the TUNE button.) The set up item changes from TEXT SCROLL ➟AVC➟XM....

1FEATURES OF YOUR HYUNDAI 130

11. TUNE/ENTER Button Turn this button clockwise by one notch to increase frequency by 200Khz from cur- rent frequency. Turn this button counterclockwise by one notch to decrease frequency by 200Khz from current frequency.

Press this button while holding SET UP button to activate / inactivate the item to select. Select SET UP item using left and right function of the Tune button.

Pressing the button changes the BASS, MIDDLE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Au- dio control knob clockwise or counter- clockwise.

o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.

o MIDDLE Control To increase the MIDDLE, rotate the knob clockwise, while to decrease the MIDDLE, rotate the knob counterclockwise.

o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.

o FADER Control Turn the control knob clockwise to empha- size rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).

o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

] button when Category Up

12. CAT(FLDR) Button Moves [CAT search operation. o Category is moved Up from the cat- egory currently being received and Category Name becomes displayed. o If the Enter Key is not pressed within 5
seconds, then the previous mode will be restored.

o If the Key is pressed while in the last Category, then the first category will become displayed and operation will be repeated.

o Corresponding category can be se-

lected by pressing ENTER.

] button when Category

Moves [CAT Down search operation. o Category is moved Down from the cat- egory currently being received and Category Name becomes displayed. o If the Enter Key is not pressed within 5
seconds, then the previous mode will be restored. o If the [CAT

] Key is pressed while in the first Category, then the last category will become displayed and operation will be repeated.

o Corresponding category can be se-

lected by pressing ENTER.

13. Pre-set Button Push [1]~[6] buttons less than 0.8 seconds to play the channel saved in each button. Push pre-set button for 0.8 seconds or longer to save current channel to the re- spective button with a beep.

PA760SC01NF-AAT

CDC (PA760S) (If Installed)

10

FEATURES OF YOUR HYUNDAI

131

13
12

11

1. CD loading slot 2. CD indicator 3. CD Eject Button 4. LOAD Button 5. CD/AUX Selection Button 6. Automatic Track Selection Button 7. INFO Button 8. TUNE/ENTER Button 9. REPEAT Button 10. RANDOM Play Button 11. DISC Selection Button 12. SCAN Play Button 13. MUTE Button

NFF_USA_CDC_CD

1FEATURES OF YOUR HYUNDAI 132

PA760SD01NF-AAT

1. CD loading slot Please face printed side upward and gen- tly push in. When the ignition switch is on ACC or ON and power is off, power is automatically turned on if the CD is loaded. This CDP supports 12 cm CD. But if VCD, Data CD are loaded, "Reading error" mes- sage will appear and CD will be ejected.

2. CD Indicator When car ignition switch is ACC or ON and if the CD is loaded, this indicator is lighted. If the CD is ejected the light is turned off.

3. CD eject Button Push button to eject the CD during CD playback. This button is enabled when ignition switch is off.

4. CD LOAD Button Push [LOAD] button to load CDs to avail- able CDC deck (from 1~6). Push [LOAD] button for more than 2 seconds to load into all available decks. The last CD will play. 10 seconds idle status will disable loading process.

5. CD/AUX Selection Button If the auxiliary device is connected, it turns to AUX MODE to play the sound from the auxiliary player. If no auxiliary device is connected, it dis- plays "NO MEDIA" for 5 seconds and re- turns to the previous mode.

6. Automatic Track Selection Button ] button for less than 0.8
o Push [SEEK seconds to play from the beginning of current song. o Push [SEEK

] button for less than 0.8
seconds and press again within 1 sec- ond to play the previous song.

o Push [SEEK

] button for 0.8 or longer to initiate reverse direction high speed sound search of current song.

o Push [SEEK

] button for less than 0.8

seconds to play the next song.

o Push [SEEK

] button for 0.8 or longer to initiate high speed sound search of current song.

7. INFO Button Displays the information of the current CD TRACK in the order of DISC TITLE➟ DISC ARTIST➟TRACK TITLE➟ TRACK ARTIST➟TOTAL TRACK➟ Play Screen➟ DISC TITLE➟···.(not displayed if the infor- mation is not available on the DISC.)

8. TUNE/ENTER Button Turn this button clockwise to display songs after current song. Also, turn this button counterclockwise to display songs before current song. To listen to the displayed song, press the button to skip to the song and play.

Pressing the button changes the BASS, MIDDLE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Au- dio control knob clockwise or counter- clockwise.

o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.

o MIDDLE Control To increase the MIDDLE, rotate the knob clockwise, while to decrease the MIDDLE, rotate the knob counterclockwise.

o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.

o FADER Control Turn the control knob clockwise to empha- size rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).

o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

FEATURES OF YOUR HYUNDAI

133

9. REPEAT Button Repeats current song when the button is pressed for less than 0.8 seconds. Repeats the entire DISC when the button is pressed for 0.8 seconds or longer.

10. RANDOM Play Button Turns on/off the randomization of the play list of files in the currently played DISC. To cancel the mode, press the key once again.

11. DISC Selection Button ] Change Button o [DISC

Changes disc to the previous disc.

o [DISC

] Change Button

Changes disc to the next disc.

12. SCAN Play Button Plays first 10 seconds of each song in the DISC. To cancel the mode, press the key once again.

13. MUTE Button Press this button to temporarily cut off the Sound. "Audio Mute" is displayed on the LCD. Press the button once again to can- cel MUTE mode.

1FEATURES OF YOUR HYUNDAI 134

PA760SE01NF-AAT

USING USB (PA760S) (If Installed)

1. AUX Selection Button 2. Track moving Button 3. INFO Selection Button 4. Folder moving Button 5. TUNE/ENTER Button 6. Random Playback Button 7. Repeat Selection Button 8. SCAN Selection Button

H_NF_A_U_CDC_USB

PA760SF01NF-AAT If a USB is connected to the multiple termi- nal inside the console on the right hand side of the driver’s seat, the ‘USB’ icon will be displayed on the top right corner of the display screen.

1.AUX Selection Button If a USB device is connected, it switches to the USB mode from the CD mode to play the song files stored in the USB device. If there is no CD and USB mode from the Radio mode, it displays ‘NO MEDIA’.

2. Track Moving Button o Press the [SEEK

] button for less than 0.8 seconds to play from the beginning of the song currently played. Press the button for less than 0.8 sec- onds and press it again within 1 second to move and play the previous track. Press the button for 0.8 seconds or longer to play the song in reverse direc- tion in fast speed. o Press the [SEEK

] button for less than 0.8 seconds to move to the next track. Press the button for 0.8 seconds or longer to play the song in forward direc- tion in fast speed.

3. INFO Button Displays the information of the file cur- rently played in the order of FILE NAME ➟TITLE➟ARTIST➟ALBUM➟FOLDER➟TOTAL FILE➟normal display➟FILE NAME➟… (Displays no information if the file has no song information.)

4. Folder moving Button o Moves [FLDR

] button child folder of the current folder and displays the first song in the folder. Press ENT/TUNE button to move to the folder displayed. It will play the first song in the folder.

o Moves [FLDR

] button parent folder and displays the first song in the folder. Press ENT/TUNE button to move to the folder displayed. It will play the first song in the folder.

5. TUNE/ENTER Button Turn this button clockwise to display the songs next to the currently played song. Turn the button counterclockwise to dis- play the songs before the currently played song. Press the button to skip and play the se- lected song.

FEATURES OF YOUR HYUNDAI

135

Pressing the button changes the BASS, MIDDLE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Au- dio control knob clockwise or counter- clockwise.

o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.

o MIDDLE Control To increase the MIDDLE, rotate the knob clockwise, while to decrease the MIDDLE, rotate the knob counterclockwise.

o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.

o FADER Control Turn the control knob clockwise to empha- size rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).

1FEATURES OF YOUR HYUNDAI 136

o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

6. RANDOM Playback Button Press the button for less than 0.8 seconds to start or stop the random playback of the songs in the current folder. Press the button for more than 0.8 seconds to randomly play the entire songs in the USB device. Press the button again to cancel the mode.

7. REPEAT Button Press the button for less than 0.8 seconds to repeat the song currently played. Press the button for more than 0.8 seconds to repeat the entire songs in the USB device.

8. SCAN Button Plays 10 seconds of each song in the USB device. Press the button once again to cancel scanning.

CAUTION IN USING USB DEVICE:

o To use the external USB device, make sure the device is not connected when starting up the vehicle and connect the device after starting up.

o If you start the vehicle when the USB device is connected, it may damage the USB device. (USB is not ESA)

o If the vehicle is started up or turned off while the external USB device is con- nected, the external USB device may not work.

o It may not play all MP3 or WMA files. 1) It can only play MP3 files with the rate between

compression 8Kbps~320Kbps.

2) It can only play WMA music files with the compression rate between 8Kbps~320Kbps.

o Take cautions for static electricity when connecting or disconnecting the external USB device.

o Encoded MP3 PLAYER'S are not rec-

ognizable.

o Depending on the condition of the ex- ternal USB device, the connected external USB device can be unrecog- nizable.

o When the formatted byte/sector set- ting of External USB devices is not either 512BYTE or 2048BYTE, then the device will not be recognized.

o Only the USB device formatted to FAT

12/16/32 can be used.

o USB device without USB

IF (Implementers-Forum) authentica- tion may not be recognizable.

o Make sure the USB connection termi- nal does not come in contact with a human body or any other object.

o If you repeat connecting or discon- necting USB device in a short period of time, it may damage the device.

o You might hear unusual noise when connecting or disconnecting a USB device.

o If you disconnect the external USB device during playback in USB mode, the external USB device can be dam- aged. Therefore, connect the exter- nal USB device when the engine is turned off or in another mode.

o Depending on the type and capacity of the external USB device or the type of the files stored in the device, there is a difference in the time taken for recognition of the device, but this does not indicate a problem.

FEATURES OF YOUR HYUNDAI

137

o Do not use the USB device for other

purposes than playing music files.

o Use of USB accessories such as a recharger or heater using the USB I/ F may lower the performance or cause trouble.

o If you use devices such as a USB hub you purchased separately, the vehicle’s audio system may not rec- ognize the USB device. Connect the USB device directly to the multimedia terminal of the vehicle.

1FEATURES OF YOUR HYUNDAI 138

PA760SG01NF-AAT

RUNNING iPod® (PA760S) (If Installed)

1. iPod Selection Button 2. Track moving Button 3. INFO Selection Button 4. Category Selection Button 5. TUNE/ENTER Button 6. RANDOM Playback Button 7. REPEAT Selection Button

* iPod® is a trademark of Apple Inc.

H_NF_A_U_CDC_IPOD

PA760SH01NF-AAT In case the iPod exclusive cable (if in- stalled) is connected to the multiple termi- nal inside the consol on the right hand side of the driver’s seat. When the iPod is con- nected, the ‘iPod’ icon will be displayed on the top right corner of the display screen.

1. iPod Selection Button If iPod is connected, it switches to the iPod mode from the CD mode to play the song files stored in the iPod. If there are no CD and AUX mode from the Radio mode, it displays ‘NO MEDIA’.

2. Track Moving Button o Press the [SEEK

] button for less than 0.8 seconds to play from the beginning of the song currently played. Press the button for less than 0.8 sec- onds and press it again within 1 second to move and play the previous track. Press the button for 0.8 seconds or longer to play the song in reverse direc- tion in fast speed. o Press the [SEEK

] button for less than 0.8 seconds to move to the next track. Press the button for 0.8 seconds or longer to play the song in forward direc- tion in fast speed.

FEATURES OF YOUR HYUNDAI

139

3. INFO Button Displays the information of the file cur- rently played in the order of FILE NAME ➟TITLE➟ARTIST➟ALBUM➟normal dis- play ➟FILE NAME➟…. (Displays no information if the file has no song information.)

4. Category Selection Button Moves to the upper category from currently played category of the iPod. To move to (play) the category (song) displayed, press MENU(preset6) You will be able to search through the lower category of the selected category. The order of iPod’s category is SONG, ALBUMES, ARTISTS, GENRES, and iPod.

5. TUNE/ENTER Button When you turn the button clockwise, it will display the songs (category) next to the song currently played (category in the same level). Also, when you turn the button counter- clockwise, it will display the songs (cat- egory) before the song currently played (category in the same level). If you want to listen to the song displayed in the song category, press the button, then it will skip to the selected song and play.

Pressing the button changes the BASS,

MIDDLE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Au- dio control knob clockwise or counter- clockwise.

o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.

o MIDDLE Control To increase the MIDDLE, rotate the knob clockwise, while to decrease the MIDDLE, rotate the knob counterclockwise.

o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.

o FADER Control Turn the control knob clockwise to empha- size rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).

o BALANCE Control

1FEATURES OF YOUR HYUNDAI 140

Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

6. RANDOM Playback Button Press the button for less than 0.8 seconds to activate or deactivate the random play- back of the songs within the current cat- egory. Press the button for longer than 0.8 sec- onds to randomly play all songs in the entire album of the iPod. Press the button once again to cancel the mode.

7. REPEAT Button Repeats the song currently played.

NOTE FOR USING iPod DEVICE: o Some iPod models might not support the communication protocol and the files will not be played. (iPod models supported: Mini, 4G, Photo, Nano, 5G) o The order of search or playback of songs in the iPod can be different from the order searched in the audio system.

o If the iPod crashes due to its own trouble, reset iPod. (Reset: Refer to iPod manual)

o iPod may not operate normally on low

battery.

CAUTION IN USING iPod DEVICE:

o You need the power cable exclusive for an iPod in order to operate iPod with the buttons on the audio system. The PC cable provided by Apple may cause a malfunction. Do not use it for vehicle use.

o When connecting the device with an iPod cable, push in the jack fully to not interfere with communication.

o When adjusting the sound of an iPod and the audio system, the sound ef- fects of both devices will overlap each and might reduce or distort the quality of the sound.

o Deactivate (turn off) the equalizer function of an iPod when adjusting the audio system’s volume, and turn off the equalizer of the audio system when using the equalizer of an iPod. o When the iPod cable is connected, the system can be switched to the AUX mode even without the iPod device and can cause noise. Disconnect iPod cable when you are not using the iPod device.

DRIVING YOUR HYUNDAI

Engine Exhaust Can Be Dangerous! ............................ 2-2
Before Starting the Engine ............................................ 2-3
Key Positions................................................................ 2-4
Starting ......................................................................... 2-5
Operating the Manual Transaxle .................................. 2-6
Automatic Transaxle ..................................................... 2-8
Power Adjustable Pedals.............................................2-12