2007 Hyundai Sonata Owners Manual

To add brake fluid, first wipe away any dirt, then unscrew the fluid reservoir cap. Slowly pour the recommended fluid into the reservoir. Do not overfill. Carefully replace the cap on the reser- voir and tighten.

DO-IT-YOURSELF MAINTENANCE

19

3. Lower the glove box down completely by pushing both sides of the glove box inward.

HNF2163

HNF2164
4. Remove the climate control air filter cover by

pressing both side clips.

CAUTION:

Be careful not to damage filter fixing clips.

CHANGING THE CLIMATE CON- TROL AIR FILTER

B145A01NF-AAT (For Evaporator and Blower Unit) (If Installed)

The climate control air filter is located in the right side of the instrument panel. It helps to decrease the amount of pollutants entering the car.

HNF2163-1

1. Remove the cover (1) which is located to the right side of the instrument panel by pulling it.

2. Pull the glove box cylinder (2) to unlock the

glove box retainer.

6 DO-IT-YOURSELF MAINTENANCE 20

CHECKING THE FREE-PLAY

G150A01A-AAT STEERING WHEEL

G160A01A-GAT CLUTCH PEDAL

HNF2165

1.18 in. (30 mm)

0.24~0.51 in. (6~13 mm)

5. Replace the climate control air filter by lifting

6.

it. Installation is the reverse order of disassem- bly.

CAUTION:

To prevent pollutants from entering the car, be sure to properly install the climate con- trol air filter.

HNF5018
To check the steering wheel free-play, stop the car with the wheels pointed straight ahead and gently move the steering wheel back and forth. Use very light finger pressure and be sensitive to changes in resistance that mark the limits of the free-play. If the free-play is greater than specified, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.

G160A01HR With the engine off, press lightly on the clutch pedal until you feel a change in resistance. This is the clutch pedal free-play. The free-play should be within the limits specified in the illus- tration. If it is not, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.

G170A01A-AAT BRAKE PEDAL

CHECKING BRAKE PEDAL CLEARANCE

G180A01A-AAT

DO-IT-YOURSELF MAINTENANCE

CHECKING DRIVE BELTS

G190A02NF-GAT

(2.4L)

Power steering Auto tensioner

21

0.12 ~ 0.31 in. (3 ~ 8 mm)

2.95 in. (75 mm)

Water pump pully

G160A01HR

With the engine off, press down on the brake pedal several times to reduce the vacuum in the brake booster. Then, using your hand, press down slowly on the brake pedal until you feel a change in resistance. This is the brake pedal free-play. The free-play should be within the limits speci- fied in the illustration above. If it is not, have it inspected by your Hyundai dealer and adjusted or repaired if necessary.

G180A01L You need a helper to check the brake pedal clearance. With the engine running, have your helper press down on the brake pedal several times and then hold it down with a force of about 110 lbs (50 kg, 490 N). The brake pedal clear- ance is the distance from the top surface of the brake pedal to the asphalt sheeting under the floor mat. If the brake pedal clearance is not within the limits specified in the illustration, have it in- spected by your Hyundai dealer and adjusted or repaired if necessary.

Generator

COMP

G140D01NF

Generator

Damper pulley

(3.3L)

Water pump pully

Auto tensioner

Power steering

Damper pulley

COMP

G140D02NF

6 DO-IT-YOURSELF MAINTENANCE 22

Drive belts should be checked periodically for proper tension. At the same time, belts should be examined for cracks, wear, fraying or other evidence of deterioration and replaced if neces- sary. When a new belt is replaced, the belt should be located within the pulley of flat idler. Belt routing should also be checked to be sure there is no interference between the belts and other parts of the engine.

NOTE: Drive belt tension is adjusted automatically by the auto tensioner.

CHECKING AND REPLACING FUSES G200A01A-AAT Replacing a Fusible Link

CAUTION:

When replacing a fusible link, never use anything but a new fusible link with the same or lower amperage rating. Never use a piece of wire or a higher-rated fusible link. This could result in serious damage and create a fire hazard.

HNF4004
A fusible link will melt if the electrical circuits from the battery are ever overloaded, thus prevent- ing damage to the entire wiring harness. (This could be caused by a short in the system drawing too much current.) If this ever happens, have a Hyundai dealer determine the cause, repair the system and replace the fusible link. The fusible links are located in a relay box in the engine compartment for easy inspection.

G200B01NF-AAT Replacing Accessory Fuse

2. Open the fuse box and examine each fuse. Remove each fuse by pulling it toward you (a small "fuse puller" tool is contained in the relay and fuse box of the engine room to simplify this operation).

3. Be sure to check all other fuses, even if you

G200B01NF-A

The fuse box for the lights and other electrical accessories will be found on the left side of the instrument panel. Inside the box you will find a list showing the circuits protected by each fuse. If any of your car's lights or other electrical accessories stop working, a blown fuse could be the reason. If the fuse has burned out, you will see that the metal strip inside the fuse has burned through. If you suspect a blown fuse, follow this procedure: 1. Turn off the ignition and all other switches.

G200B02NF

find one that appears to have burned out. 4. Replace the blown fuse by pressing a new fuse of the same rating into place. The fuse should be a snug fit. If it is not, have the fuse clip repaired or replaced by a Hyundai dealer. If you do not have a spare fuse, you may be able to borrow a fuse of the same or lower rating from an accessory you can tempo- rarily get along without (the radio or cigarette lighter, for example). Always remember to replace the borrowed fuse.

DO-IT-YOURSELF MAINTENANCE

23

Good

Burned out

G200B02L

CAUTION:

A burned-out fuse indicates that there is a problem in the electrical circuit. If you re- place a fuse and it blows as soon as the accessory is turned on, the problem is serious and should be referred to a Hyundai dealer for diagnosis and repair. Never re- place a fuse with anything except a fuse with the same or a lower amperage rating. A higher capacity fuse could cause damage and create a fire hazard.

NOTE: See page 6-36 for the fuse panel descrip- tions.

6 DO-IT-YOURSELF MAINTENANCE 24

CHECKING THE BATTERY

G210A01A-AAT

HNF5017

WARNING:

Batteries can be dangerous! When working with batteries, carefully observe the follow- ing precautions to avoid serious injuries.

The fluid in the battery contains a strong solution of sulfuric acid, which is poisonous and highly corrosive. Be careful not to spill it on yourself or the car. If you do spill battery fluid on yourself, immediately do the following:

o If battery fluid is on your skin, flush the affected areas with water for at least 15
minutes and then seek medical assistance. o If battery fluid is in your eyes, rinse out your eyes with water and get medical assistance as soon as possible. While you are being driven to get medical assistance, continue to rinse your eyes by using a sponge or soft cloth saturated with water.

o If you swallow battery fluid, drink a large quantity of water or milk followed by milk of magnesia, eat a raw egg or drink vegetable oil. Get medical assistance as soon as possible.

While batteries are being charged (either by a battery charger or by the vehicle's generator), they produce explosive gases. Always ob- serve these warnings to prevent injuries from occurring:

G210B04A-AAT Checking the Battery

Keep the battery clean. Any evidence of corro- sion around the battery posts or terminals should be removed using a solution of house- hold baking soda and warm water. After the battery terminals are dry, cover them with a light coating of grease.

PROPOSITION 65 WARNING: Battery posts, terminals, and related acces- sories contain lead and lead compounds, chemicals known to the state of California to cause cancer and reproductive harm. Batteries also contain other chemicals known to the state of California to cause cancer. Wash hands after handling.

o Charge batteries only in a well ventilated

o Do not permit flames, sparks or smoking in

area.

the area.

o Keep children away from the area.

!

WARNING: Always read the following in- structions carefully when han- dling a battery.

Keep lighted cigarettes and all other flames or sparks away from the battery.

Hydrogen, which is a highly com- bustible gas, is always present in battery cells and may explode if ignited.

Keep batteries out of the reach of children because batteries con- tain highly corrosive SULFURIC ACID. Do not allow battery acid to contact your skin, eyes, cloth- ing or paint finish.

If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immediate medical attention. If possible, continue to apply water with a sponge or cloth until medical attention is received.

WARNING: If electrolyte gets on your skin, thoroughly wash the contacted area. If you feel a pain or a burning sensation, get medical attention immediately.

Wear eye protection when charg- ing or working near a battery. Always provide ventilation when working in an enclosed space.

o When lifting a plastic-cased battery, ex- cessive pressure on the case may cause battery acid to leak, resulting in personal injury. Lift with a battery carrier or with your hands on opposite corners.

o Never attempt to charge the battery when

the battery cables are connected.

o The electrical ignition system works with

high voltage. Never touch these components with the engine running or the ignition switched on.

DO-IT-YOURSELF MAINTENANCE

CHECKING ELECTRIC COOLING FANS G220A01A-AAT

25

WARNING:

The cooling fan is controlled by engine coolant temperature and may sometimes operate even when the engine is not run- ning. Use extreme caution when working near the blades of the cooling fan, so that you are not injured by a rotating fan blade. As the engine coolant temperature de- creases the fan will automatically shut off. This is a normal condition.

G220B01NF-GAT Checking Engine Cooling Fan

The engine cooling fan should come on auto- matically if the engine coolant temperature is high or whenever the air conditioning is in operation.

6 DO-IT-YOURSELF MAINTENANCE 26

POWER STEERING FLUID LEVEL

G230A01NF-AAT (2.4L)

FOR MORE INFORMATION ABOUT YOUR HYUNDAI

G250A01A-AAT If you desire additional information about main- taining and servicing your Hyundai, you may purchase a factory Shop Manual at your Hyundai dealer's parts department. This is the same manual used by dealership technicians and while it is highly technical it can be useful in obtaining a better understanding of your car and how it works.

to make certain that the power steering fluid level is between the "MAX" and "MIN" level markings on the fluid reservoir.

NOTE: Grinding noise from the power steering pump may be heard immediately after the engine is started in extremely cold condi- tions (below - 4°F). If the noise stops during warm up, there is no abnormal function in the system. It is due to a power steering fluid characteristic in extremely cold condi- tions.

(3.3L)

G230A01NF

Recommended Fluid Use PSF-4 type fluid

NOTE: Do not start the engine when the power steering oil reservoir is empty.

G240A01A-AAT POWER STEERING HOSES

It is suggested that you check the power steer- ing hose connections for fluid leakage at those intervals specified in the vehicle maintenance schedule in Section 5. The power steering hoses should be replaced if there is severe surface cracking, pulling, scuffing or worn spots. Deterioration of the hose could cause premature failure.

G230A02NF The power steering fluid level should be checked regularly. To check the power steering fluid level, be sure the engine is "OFF", then check

HEADLIGHT AIMING ADJUSTMENT

G290A03O-AAT Before performing aiming adjustment, make sure of the following. 1. Keep all tires inflated to the correct pressure. 2. Place the vehicle on level ground and press the front bumper & rear bumper down sev- eral times. Place vehicle at a distance of 118 in. (3m) from the test wall.

3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and tools). Have the driver or equivalent weight placed in driver's seat. 4. Clean the headlight lenses and turn on the

headlights (Low beam).

5. Open the hood.

Vertical aiming

G290A01NF-A

6. Draw a vertical line (through the center of each headlight beam pattern) and a horizon- tal line (through the center of each headlight beam pattern) on the aiming screen. And then, draw a parallel line at 0.8 in. (21
mm) under the horizontal line.

7. Adjust each cut-off line of the low beam to the parallel line with a phillips screwdriver - VERTICAL AIMING.

WARNING:

Never attempt to adjust the horizontal align- ment of your headlights. Horizontal aiming must be adjusted by an authorized Hyundai dealer to avoid incorrect alignment that will reduce the effectiveness of your headlights.

DO-IT-YOURSELF MAINTENANCE

27

G290B01NF-AAT Adjustment After Headlight Assembly Replacement

0.8 in.(21 mm)

Vertical line

Horizontal line

"P"

Cut-off line

Ground line

G260B01GK If the vehicle has had front body repair and the headlight assembly has been replaced, the headlight aiming should be checked using the aiming screen as shown in the illustration. Turn on the headlight switch (Low Beam Position). 1. Adjust headlights so that main axis of light is parallel to the center line of the body and is aligned with point "P" shown in the illustration. 2. Dotted lines in the illustration show the center

of the headlights.

6 DO-IT-YOURSELF MAINTENANCE 28

SPECIFICATION: "H" Horizontal center line of headlights from ground : 26.73 in. (679mm)

"W" Distance between each headlight center : 51.41 in. (1,306mm)

"L" Distance between the headlights and the wall that the lights are tested against : 118.11 in. (3,000 mm)

REPLACEMENT OF LIGHT BULBS

G260A02L-GAT Before attempting to replace a light bulb, be sure the switch is turned to the "OFF" position. The next paragraph shows how to reach the light bulbs so they may be changed. Be sure to replace the burned-out bulb with one of the same number and wattage rating. See page 6-35 for the wattage descriptions.

G270A01NF-AAT HEADLIGHT, FRONT TURN SIGNAL LIGHT AND FRONT FOG LIGHT

Headlight and Front Turn Signal Light

Headlight (High beam)

Headlight (Low beam)

CAUTION:

o Keep the lights out of contact with pe- troleum products, such as oil, gasoline, etc.

o Be sure to replace the LED type equipped

bulbs with an assembly.

o After heavy, driving rain or washing, headlight and taillight lenses could ap- pear frosty. This condition is caused by the temperature difference between the lamp inside and outside. This is similar to the condensation on your windows inside your vehicle during the rain and doesn’t indicate a problem with your vehicle. If the water leaks into the lamp bulb circuitry, have the vehicle checked by an Authorized Hyundai Dealer.

Front Fog Light

Turn signal light (Front position light)

G260A01NF-A

Replacement instructions:

1. Allow the bulb to cool. Wear eye protection. 2. Open the engine hood. 3. Always grasp the bulb by its plastic base,

avoid touching the glass.

DO-IT-YOURSELF MAINTENANCE

29

HNF5026
7. Disconnect the connector from the bulb base in

the back of the headlight.

8. Push the bulb spring to remove the headlight

bulb.

HNF5023
4. Using a socket wrench of the correct size, remove the headlight assembly mounting bolts.

HNF5025
6. Turn the plastic cover counterclockwise

and remove it.

HNF5024
5. Disconnect the power cord from the back of

the headlight.

6 DO-IT-YOURSELF MAINTENANCE 30

Type A

10. Use the protective cap and carton to

promptly dispose of the old bulb. 11. Check for proper headlight aim.

HNF5027

G270A03O

Type B (Low Beam)

HNF5028

12. To replace the front turn signal light bulb (front position light), remove it from the bulb holder and install the new bulb.

OMG075038N 9. Remove the protective cap from the re- placement bulb and install the new bulb by matching the plastic base with the headlight hole. Reattach the bulb spring and recon- nect the connector.

WARNING:

This halogen bulb contains gas under pres- sure and if impacted could shatter, result- ing in flying fragments. Always wear eye protection when servicing the bulb. Protect the bulb against abrasions or scratches and against liquids when lighted. Turn the bulb on only when installing in a headlight. Replace the headlight if damaged or cracked. Keep the bulb out of the reach of children and dispose of the used bulb with care.

Front Fog Light

NOTE: It is recommended that the front fog light bulb should be replaced by an authorized Hyundai dealer.

G270D01NF-AAT REAR COMBINATION LIGHT

Stop/Tail Light, Rear Turn Signal Light, Back-up Light and Rear Side Marker Light

1. Open the trunk lid.

DO-IT-YOURSELF MAINTENANCE

31

HNF5030-A

3. To replace the rear combination light (stop/ tail light, rear side marker light and rear turn signal light), remove it from the bulb holder and install the new bulb.

(1) Stop/tail light (2) Rear side marker light (3) Rear turn signal light

HNF5029

2. Remove the cover on the inside of the rear luggage trim by turning the knob counter- clockwise.

6 DO-IT-YOURSELF MAINTENANCE 32

G270C01L-AAT LUGGAGE COMPARTMENT LIGHT

1. Open the trunk lid.

HNF5042

4. Loosen the mounting screws of the trunk lid trim with a phillips screwdriver and remove the trunk lid trim.

5. To replace the rear combination light (back- up light and stop/tail light), remove the socket by turning it counterclockwise. Install the new bulb.

6.

HNF5031-A

2. Remove the luggage compartment light cover on the rear package tray panel with a flat- head screwdriver.

3. Disconnect the power cord.

HNF5032

4. Replace with a new bulb.

HTB284

G270G01L-AAT INTERIOR LIGHT

G270L01L-AAT MAP LIGHT

DO-IT-YOURSELF MAINTENANCE

33

Screwdriver

HNF5034

2. Replace with a new bulb.

HNF5035

1. Remove the plastic cover with a flat-head

screwdriver.

1. Remove the plastic cover with a flat-head

screwdriver.

G270G01NF

6 DO-IT-YOURSELF MAINTENANCE 34

G270K01L-AAT GLOVE BOX ILLUMINATED LIGHT

1. Open the glove box.

2. Replace with a new bulb.

G270G02NF

Screwdriver

3. Disconnect the power cord.

HJM5039

2. Remove the glove box illuminated light cover

with a flat-head screwdriver.

HNF5036

4. Replace with a new bulb.

HTB284

BULB WATTAGES

G280A01NF-AAT

DO-IT-YOURSELF MAINTENANCE

35

No.

Headlight

Part Name Low beam High beam

Front Turn Signal Light/Front Position Light Map Light Interior Light Front Fog Light Front Side Marker Light Front Door Edge Warning Light

Wattage

Socket Type

55
55
28/8
10
10
27

P x 26d P14,5s BAY15d

w2.1 x 9.5d

sv6-7,6
PGJ13
BAY15d

w2.1 x 4.6d

No. 10
11
12
13
14
15

Part Name

Wattage

Socket Type

Stop / Tail Light High Mounted Rear Stop Light Tail Light Luggage Compartment Light Rear Side Marker Light Rear Turn Signal Light Back-up Light License Plate Light

28/8
16
28/8

27
16

BAY 15d

w2.1 x 9.5d

BAY 15d sv6-7, 6
BAY 15d BAY15s

w2.1 x 9.5d w2.1 x 9.5d

G280A01NF-A

6 DO-IT-YOURSELF MAINTENANCE 36

FUSE PANEL DESCRIPTION

G200C01NF-AAT Engine Compartment

NOTE: Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of printing. When you inspect the fuse box on your vehicle, refer to the fuse box label.

HNF4005-1

DO-IT-YOURSELF MAINTENANCE

37

DESCRIPTION

FUSE RATING

FUSIBLE

LINK

FUSE

ABS.1
ABS.2
I/P B+1
RR HTD BLOWER P/WDW IGN.2

ECU RLY I/P B+2
IGN.1
ALT MDPS

10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

HORN TAIL ECU IG1
DRL

FR FOG A/CON F/PUMP DIODE ATM STOP

H/LP LO RH

S/ROOF

H/LP WASHER

H/LP HI

ECU

SNSR.3
SNSR.1
SNSR.2

B/UP

IGN COIL ECU (IG1) H/LP LO

ABS

40A 20A 40A 40A 40A 40A 40A 30A 30A 30A 150A 100A 15A 20A 10A 10A 15A 15A 10A 20A

20A 15A 15A 15A 20A 20A 10A 10A 15A 15A 10A 20A 10A 20A 10A

PROTECTED COMPONENTS ABS/ESC control module, Multipurpose check connector ABS/ESC control module, Multipurpose check connector Fuse 23, 24, 30, 31, 32, 33, 34, 35
Defogger relay Blower relay Power window relay, Fuse 16
Start relay, Ignition switch (IG2, START) Engine control unit relay Power connector 1/2, Fuse 21,22
Ignition switch (ACC, IG1) Fusible Iink (ABS. 1, ABS. 2, RR HTD, BLOWER) (Spare) Horn relay Tail light relay PCM (Spare) Siren relay, DRL control module Front fog light relay A/C relay Fuel pump relay (Spare) ATM control relay Stop light relay (Spare) Sunroof control module Headlight washer motor Headlight relay (High) (Spare) Oxygen sensor, Fuel pump relay Mass air flow sensor, Crankshaft/Camshaft position sensor, Oil control valve, SMATRA A/C relay, Cooling fan relay, Injectors Back up light switch, Pulse generator, Vehicle speed sensor Ignition coils, Condenser PCM Headlight relay (Low) ABS/ESC control module, Multipurpose check connector

6 DO-IT-YOURSELF MAINTENANCE 38

G200E01NF-AAT Inner Panel

HNF4003

DO-IT-YOURSELF MAINTENANCE

39

FUSE

FUSE RATING

PROTECTED COMPONENTS

10
11
12
13
14
15
16
17
18
19
20

15A 15A 10A 10A 25A 10A 10A 10A 10A 10A 25A 10A 15A 20A 10A 25A 15A 10A 20A 30A

(Spare) Seat warmer switch BCM(Body Control Module), Sunroof control module, Electronic chrome mirror ESC module, High blower relay, Humidity sensor Cigarette lighter (Spare) Illumination lights, Right : License light, Rear combination light, Headlight, Glove box light Front fog light relay, Left : License light, Rear combination light, Headlight Headlight washer relay, Right headlight leveling actuator DRL control module, Headlight relay, AQS and ambient sensor, Left headlight leveling actuator Wiper and washer A/C control module SRS control module, Passenger's Airbag switch Front accessory socket, Rear power outlet Digital clock, Audio, A/T shift lock control module, Power outside mirror and mirror folding Safety window module (Spare) A/T shift lock control module Power window main switch, Left rear power window switch Power window main switch, Right power window switch

6 DO-IT-YOURSELF MAINTENANCE 40

FUSE

FUSE RATING

PROTECTED COMPONENTS

21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

POWER CONNECTOR. 1
POWER CONNECTOR. 2

20A 20A 10A 30A 10A 10A 10A 15A 10A 15A 15A 15A 15A 30A 10A 10A 15A 15A

Audio amp Door lock/unlock relay Hazard switch, Hazard relay Power seat manual switch(RHD) Instrument cluster Hazard switch BCM(Body Control Module), Instrument cluster, Yaw rate sensor, ESC switch (Spare) Burglar alarm relay (Spare) Rear fog light relay Trunk lid relay, Fuel filler door and trunk lid switch (Spare) Power seat manual switch Sport mode switch, Key solenoid A/C control module, Outside mirror and mirror folding motor Audio BCM(Body Control Module), Digital clock, Instrument cluster, A/C control module, Courtesy lights

EMISSION CONTROL SYSTEMS

Emission Control System ............................................. 7-2
Catalytic Converter ....................................................... 7-3

7 EMISSION CONTROL SYSTEMS EMISSION CONTROL SYSTEMS

H010A01NF-AAT Your Hyundai is equipped with an emission control system to meet all emission regulations. There are three emission control systems which are as follows.

(1) Crankcase emission control system (2) Evaporative emission control system (3) Exhaust emission control system

In order to assure the proper function of the emission control systems, it is recommended that you have your car inspected and main- tained by an authorized Hyundai dealer in ac- cordance with the maintenance schedule in this manual.

Caution for the Inspection and Maintenance Test (With Electronic Stability Control (ESC) system)

o To prevent the vehicle from misfiring during dynamometer testing, turn the Electronic Stability Control (ESC) sys- tem off by pressing the ESC switch.

o After dynamometer testing is completed, turn the ESC system back on by pressing the ESC switch again.

H010B01A-AAT 1. Crankcase Emission Control System

The positive crankcase ventilation system is employed to prevent air pollution caused by blow-by gases being emitted from the crank- case. This system supplies fresh filtered air to the crankcase through the air intake hose. Inside the crankcase, the fresh air mixes with blow-by gases, which then pass through the PCV valve into the induction system.

H010C01S-AAT 2. Evaporative Emission Control (Includ- ing ORVR: Onboard Refueling Vapor Recovery) System

The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere. (The ORVR system is designed to allow the vapors from the fuel tank to be loaded into a canister while refueling at the gas station, pre- venting the escape of fuel vapors into the atmosphere.)

Canister

Fuel vapors generated inside the fuel tank are absorbed and stored in the onboard canister. When the engine is running, the fuel vapors absorbed in the canister are drawn into the surge tank through the purge control solenoid valve.

Purge Control Solenoid Valve (PCSV)

The purge control solenoid valve is controlled by the Engine Control Module (ECM); when the engine coolant temperature is low during idling, the PCSV closes so that evaporated fuel is not taken into the engine. After the engine warms- up during ordinary driving, the PCSV opens to introduce evaporated fuel to the engine.

H010D01A-AAT 3. Exhaust Emission Control

System

The Exhaust Emission Control System is a highly effective system which controls exhaust emissions while maintaining good vehicle per- formance.

EMISSION CONTROL SYSTEMS

WARNING:

o Remember that your Hyundai dealer is

your best source of assistance.

o Do not stop your Hyundai over any com- bustible material such as grass, paper, leaves or rags. These materials might contact the hot catalytic converter and a fire might result.

CATALYTIC CONVERTER

H020A01A-AAT

Catalytic Converter

H020A01NF

All Hyundai vehicles are equipped with a mono- lith type three-way catalytic converter to re- duce the carbon monoxide, hydrocarbons and nitrogen oxides contained in the exhaust gas. Exhaust gases passing through the catalytic converter cause it to operate at a very high temperature. The introduction of large amounts of unburned gasoline into the exhaust may cause the catalytic converter to overheat and create a fire hazard. This risk may be reduced by observing the following:

WARNING:

o Use unleaded fuel only. o Maintain the engine in good operating condition. Extremely high catalytic con- verter temperatures can result from im- proper operation of the electrical, igni- tion or multiport electronic fuel injec- tion.

o If your engine stalls, pings, knocks, or is hard to start, have your Hyundai dealer inspect and repair the problem as soon as possible.

o Avoid driving with a very low fuel level. Running out of gasoline may cause the engine to misfire and result in damage to the catalytic converter.

o Avoid idling the engine for periods

longer than 10 minutes.

o The vehicle should not be pushed or pulled to get started. This may cause the catalytic converter to overheat and cre- ate a fire hazard.

o Do not touch the catalytic converter or any other part of the exhaust system while the catalytic converter is hot. Shut off the engine, wait for at least one hour before touching the catalytic converter or any other part of the exhaust system.

CONSUMER INFORMATION, REPORTING

SAFETY DEFECTS & BINDING

ARBITRATION OF WARRANTY CLAIMS

Vehicle Identification Number (VIN) .............................. 8-2
Engine Number ............................................................. 8-2
Tire Information ............................................................. 8-2
Recommended Cold Tire Inflation Pressures ............... 8-3
Checking Tire Inflation Pressure ................................... 8-4
Tire Sidewall Labeling ................................................... 8-5
Tire Terminology and Definitions ................................... 8-7
All Season Tires ............................................................ 8-9
Snow Tires .................................................................... 8-9
Tire Chains.................................................................... 8-9
Tire Rotation................................................................ 8-10
Tire Balancing ............................................................. 8-10
Tire Traction ................................................................ 8-11
When to Replace Tires ............................................... 8-11
Tire Maintenance ........................................................ 8-12
Spare Tire and Tools................................................... 8-13
Warranties for Your Hyundai Vehicle .......................... 8-13
Consumer Information ................................................. 8-14
Reporting Safety Defects ............................................ 8-16
Binding Arbitration of Warranty Claims ....................... 8-17

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

ENGINE NUMBER

VEHICLE IDENTIFICATION NUMBER (VIN)

I010A01O-AAT

I010B01A-AAT (2.4L)

I010A01NF-A The vehicle identification number (VIN) is the number used in registering your car and in all legal matters pertaining to its ownership, etc. It can be found in three different places on your car:

(3.3L)

HNF6003

TIRES

I020A02A-AAT TIRE INFORMATION The tires supplied on your new Hyundai are chosen to provide the best perfor- mance for normal driving. If you ever have questions about your tire warranty and where to obtain ser- vice, see the tire manufacturer's book- let included with your vehicle's Owner's Manual Literature Kit.

1. On the bulkhead between the engine and

passenger compartments.

2. On the left top side of the instrument panel where it can be seen by looking down through the windshield.

3. On the lower side of the center pillar outer

panel.

The engine number is stamped on the engine block as shown in the drawing.

I010B01NF

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

I030A03NF-AAT

RECOMMENDED COLD TIRE INFLA- TION PRESSURES

Type A

Type C

Type B

I030A01NF-A Tire label located on the driver's side of the center pillar outer panel gives the cold tire pressures recommended for your vehicle with the original tire size, the number of people that can be in your vehicle and vehicle capacity weight.

I030A03NF-A

i030a05nf-a

These pressures were chosen to pro- vide the most satisfactory combination of ride comfort, tire wear and stability under normal conditions. Tire pressures should be checked at least monthly. Proper tire inflation pressures should be maintained for these reasons:

I030A04NF-A

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

! WARNING:

o Inspect your tires frequently for proper inflation as well as wear and damage. Always use a tire pressure gauge.

o Tires with too much or too little pressure wear unevenly causing poor handling, loss of vehicle control, and sudden tire failure leading to accidents, injuries, and even death. The recommended cold tire pressure for your vehicle can be found in this manual and on the tire label located on the driver's side of the center pillar. o Worn tires can cause accidents. Replace tires that are worn, show uneven wear, or are damaged. See page 8-11.

o Remember to check the pressure of your spare tire. Hyundai recom- mends that you check the spare every time you check the pressure of the other tires on your vehicle.

NOTE: o Underinflation also results in ex- cessive wear, poor handling and reduced fuel economy. Wheel de- formation also is possible. Keep your tire pressures at the proper levels. If a tire frequently needs refilling, have it checked by your Hyundai Dealer.

o Overinflation produces a harsh ride, excessive wear at the center of the tire tread, and a greater possibility of damage from road hazards.

WARNING:

Overinflation or underinflation can reduce the tire life, adversely affect vehicle handling, and lead to sud- den tire failure. This could rusult in loss of vehicle control and potential injury.

CAUTION:

Always observe the following:

o Check pressures when the tires are cold. (After the vehicle has been parked for at least three hours or hasn't been driven more than 1
mile (1.6 km) since starting up.)

o Check the pressure of your spare tire each time you check the pres- sure of other tires.

o Worn, old tires can cause acci- dents. If your tread is badly worn, or if your tires have been dam- aged, replace them.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

I035A01JM-AAT

CHECKING TIRE INFLATION PRES- SURE Check your tires once a month or more. Also, check the tire pressure of the spare tire.

How to Check Use a good quality gauge to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your vehicle has been sitting for at least three hours or driven no more than 1
mile (1.6 km).

Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure mea- surement. If the cold tire inflation pres- sure matches the recommended pres- sure on the tire and loading information label, no further adjustment is neces- sary. If the pressure is low, add air until you reach the recommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pres- sure with the tire gauge. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.

I030B01NF-AAT TIRE SIDEWALL LABELING

5, 6

I030B04JM

Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamen- tal characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

1. Manufacturer or Brand name

o Manufacturer or Brand name is

shown. 2. Tire size

(example: P215/60R16 94V) o The "P" indicates the tire is de-

signed for passenger vehicles.

o Three-digit number (215): This num- ber gives the width in millimeters of the tire from sidewall edge to sidewall edge.

o Two-digit number (60): This num- ber, known as the aspect ratio, gives the tire's ratio of height to width.

o R: The "R" stands for radial. o Two-digit number (16): This num- ber is the wheel or rim diameter in inches.

o Two digit number (94): This num- ber is the tire's load index. It is a measurement of how much weight each tire can support.

o V: Speed Rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time. The ratings range from "A" to "Z" (98 to 186 MPH). 3. TIN (Tire Identification Number) for new tire (example: DOT XX XX XXX XXXX) o DOT: Abbreviation for the "Depart- ment of Transportation". The sym- bol can be placed above, below or to the left or right of the Tire Iden- tification Number. It indicates the tire is in compliance with the U.S. Department of Transportation Mo- tor Vehicle Safety Standards.

o 1st two-digit code: Manufacturer's

identification mark

o 2nd two-digit code: Tire size o 3rd three-digit code: Tire type code

(Optional)

o 4th four-digit code: Date of Manu-

facture

o Four numbers represent the week and year the tire was built. For example, the numbers 3105 means the 31st week of 2005.

4. Tire ply composition and material The number of layers or plies of rubbercoated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which in- clude steel, nylon, polyester, and others. The letter "R" means radial ply construction; the letter "D" means diagonal or bias ply construction; and the letter "B" means belted-bias ply construction.

5. Maximum permissible inflation

pressure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure. Refer to the Tire and Loading Information label for recommended inflation pres- sure.

6. Maximum load rating

This number indicates the maximum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire.

7. Uniform Tire Quality Grading

(UTQG): Tire manufacturers are required to grade tires based on three perfor- mance factors: treadwear, traction and temperature resistance. For more information, see Uniform Tire Qual- ity Grading on page 8-14.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

I030D01JM-AAT

TIRE TERMINOLOGY AND DEFINI- TIONS Air Pressure: The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accesso- ries. Some examples of optional ac- cessories are, automatic transmission, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.

Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. Curb Weight: This means the weight of a motor vehicle with standard and op- tional equipment including the maxi- mum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Depart- ment of Transportation motor vehicle safety standards. The DOT code in- cludes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating GAWR FRT: Gross Axle Weight Rating for the front Axle. GAWR RR: Gross Axle Weight Rating for the rear axle.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

Intended Outboard Sidewall: The side of an asymmetrical tire, that must al- ways face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Load Index: An assigned number rang- ing from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rat- ing for a tire at the maximum permis- sible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. Normal Occupant Weight: The num- ber of occupants a vehicle is designed to seat multiplied by 150 pounds (68
kg).

Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particu- lar side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering or bears manufacturer, brand and or model name molding that is higher or deeper than the same mold- ings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. Radial Ply tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire upon which the tire beads are seated.

Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maxi- mum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a tire when only 2/32
inch of tread remains. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire's traction, temperature and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire.

Vehicle Capacity Weight: The number of designated seating positions multi- plied by 150 lbs. (68 kg) plus the rated cargo and luggage load. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight. Vehicle Normal Load on the Tire: That load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occupant weight and dividing by 2. Vehicle Placard: A label permanently attached to a vehicle showing the origi- nal equipment tire size and recom- mended inflation pressure.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

I040B01JM-AAT

ALL SEASON TIRES Hyundai specifies all season tires on some models to provide good perfor- mance for use all year round, including snowy and icy road conditions. All sea- son tires are identified by ALL SEASON and/or M+S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than all season tires an may be more appropriate in some areas.

Snow tires should carry 4 psi (28 kPa) more air pressure than the pressure recommended for the standard tires on the tire label on the driver's side of the center pillar , or up to the maximum pressure shown on the tire sidewall, whichever is less. Do not drive faster than 75 mph (120
km/h) when your car is equipped with snow tires.

I040A01O-AAT

SNOW TIRES If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; otherwise, poor han- dling may result.

I050A04Y-AAT

TIRE CHAINS Tire chains, if necessary, should be installed on the front wheels. Be sure that the chains are the proper size and that they are installed in accordance with the manufacturer's instructions. To minimize tire and chain wear, do not continue to use tire chains when they are no longer needed.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 10

! WARNING:

o When driving on roads covered with snow or ice, drive at less than 20 mph (30 km/h).

o Use the SAE "S" class or wire &

plastic chains.

o If you have noise caused by chains contacting the body, retighten the chain to avoid contact with the vehicle body.

o To prevent body damage, retighten the chains after driving 0.3~0.6
miles.

o Don't use a tire chains on a vehicle equipped with aluminium wheels. If it is unavoidable use wire-type chains.

o Use wire chains less than 15mm to prevent damage to the chain's con- nection.

I060A02A-AAT

TIRE ROTATION

I060A02NF Tires should be rotated every 7,500
miles (12,000 km). If you notice that tires are wearing unevenly between ro- tations, have the car checked by a Hyundai dealer so the cause may be corrected. After rotating, adjust the tire pressures and be sure to check the wheel nut torque.

WARNING:

o Do not use the temporary spare

tire for tire rotation.

o Do not mix bias ply and radial ply tires under any circumstances. This may cause unusual handling characteristics that could result in death, serious injury, or property damage.

I070A01A-AAT

TIRE BALANCING A tire that is out of balance may affect handling and tire wear. The tires on your Hyundai were balanced before the car was delivered but may need balancing again during the years you own the car. Whenever a tire is dismounted for re- pair, it should be rebalanced before being reinstalled on the car.

I080A01A-AAT

TIRE TRACTION Tire traction can be reduced if you drive on worn tires, tires that are improperly inflated or on slippery road surfaces. Tires should be replaced when tread wear indicators appear. To reduce the possibility of losing control, slow down whenever there is rain, snow or ice on the road.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

11

I090A04JM-AAT

WHEN TO REPLACE TIRES

0.06 in. (1.6 mm)

Tread wear indicator

HNF5015
The original tires on your car have tread wear indicators. The location of tread wear indicators is shown by the "TWI" or " " marks, etc. The tread wear indicators appear when the tread depth is 0.06 in. (1.6 mm). The tire should be replaced when these appear as a solid bar across two or more grooves of the tread. Always replace your tires with those of the recommended size. If you change wheels, the new wheel's rim width and offset must meet Hyundai specification.

! WARNING:

To reduce the chance or serious or fatal injuries from an accident caused by tire failure or loss of vehicle con- trol: o Replace tires that are worn, show uneven wear, or are damaged. Worn tires can cause loss of brak- ing effectiveness, steering con- trol, and traction.

o Do not drive your vehicle with too little or too much pressure in your tires. This can lead to uneven wear and tire failure.

o When replacing tires, never mix radial and bias-ply tires on the same car. You must replace all tires (including the spare) if mov- ing from radial to bias-ply tires.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 12

WARNING:

o Using tires and wheel other than the recommended sizes could cause unusual handling charac- teristics and poor vehicle control, resulting in a serious accident.

o Wheels that do not meet Hyundai's specifications may fit poorly and result in damage to the vehicle or unusual handling and poor ve- hicle control.

WARNING:

Tires degrade over time, even when they are not being used. Regardless of the remaining tread, it is recom- mended that tires tread, It is recom- mended that tires generally be re- placed after 6 years of normal ser- vice. Heat caused by not climates or frequent high loading Conditions can accelerate the aging process. Fail- ure to follow this Warning can result in sudden tire failure, which could lead to a loss of control and an accident involving serious injury or death.

I090B02JM-AAT

TIRE MAINTENANCE In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel align- ment.

When you have new tires installed, make sure they are balanced. This will increase vehicle ride comfort and tire life. Additionally, a tire shoud always be rebalanced if it is removed from the wheel.

!

WARNING:

o Underinflated or overinflated tires can cause poor handling, loss of vehicle control, and sudden tire failure leading to accidents, inju- ries, and even death. Always check tires are properly inflated before driving. Refer to pages 2-22 and 8- 3 for proper tire pressures and further information.

o Driving on tires with no or insuffi- cient tread is dangerous. Worn- out tires can result in loss of ve- hicle control, collisions, and in- jury and even death. Worn-out tires should be replaced as soon as possible and should never be used for driving. Always check tire tread before driving your car. Refer to this page for further infor- mation and tread limits.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

SPARE TIRE AND TOOLS

I100A01NF-AAT

WARRANTIES FOR YOUR HYUNDAI VEHICLE

I120A03A-AAT Please consult your Owner’s Handbook & Warranty Information booklet for your vehicle’s specific warranty coverage.

13

I100A01NF-A Your Hyundai is delivered with the fol- lowing: Spare tire and wheel Wrench bar (1) Jack (2) Wheel nut wrench (3) Tool receptacle (4)

I110A01A-AAT SHOP MANUAL

A Hyundai Shop Manual is available from your authorized Hyundai dealer. It's written for pro- fessional technicians, but is simple enough for most mechanically-inclined owners to under- stand.

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 14

CONSUMER INFORMATION

I130A01A-AAT This consumer information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Hyundai automobiles with infor- mation on uniform tire quality grading. Your Hyundai dealer will help answer any questions you may have as you read this information.

Traction AA, A, B, C - The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pave- ment as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction per- formance.

! WARNING:

The traction grade assigned to this tire is based on straight-ahead brak- ing traction tests, and does not in- clude acceleration, cornering, hy- droplaning, or peak traction charac- teristics.

I130B04A-AAT

Tire Quality Grading Department of Transportation quality grades - All passenger vehicle tires must conform to Federal Safety Stan- dards in addition to these grades. These quality grades are molded on the sidewall.

Treadwear - The treadwear grade is a comparative rating based on the wear rate of the tire when tested under con- trolled conditions on a specified gov- ernment test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to varia- tions in driving habits, service prac- tices and differences in road character- istics and climate.

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS

15

Temperature A, B, C - The tempera- ture grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under con- trolled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

! WARNING:

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Exces- sive speed, underinflation, or exces- sive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Uniform Tire Quality Grading - Qual- ity grades can be found on the tire sidewall between the tread shoulder and the maximum section width. For example : Treadwear 200 Traction AA Tempera- ture A

I130D04A-AAT Hyundai motor vehicles are designed and manu- factured to meet or exceed all applicable safety standards.

For your safety, however, we strongly urge you to read and follow all directions in this Owner's Manual, particularly the information under the headings "NOTE", "CAUTION" and "WARN- ING".

If, after reading this manual, you have any questions regarding the operation of your ve- hicle, please contact your nearest Hyundai Motor America Regional Office as listed below:

Eastern Region : Connecticut, Delaware, Maine, Maryland, Massachusetts, New Hamp- shire, New Jersey, New York, Pennsylvanina, Rhode Island, Vermont, Virginia, West Virginia.

Eastern Region 1100 Cranbury South River Road Jamesburg, NJ 08831
(800) 633-5151

8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 16

Western Region: Alaska, Hawaii, Arizona, California, ldaho, Montana, Nevada, Oregon, Texas, Utah, Washington.

Western Region 10550 Talbert Avenue P.O.Box 20850
Fountain Valley, California 92728-0850
(800) 633-5151