2012 Hyundai Santa FE Owners Manual

WARNING

Removing radiator cap

(cid:129) Never attempt to remove the radi- ator cap while the engine is oper- ating or hot. Doing so might lead to cooling system and engine damage and could result in seri- ous personal injury from escap- ing hot coolant or steam.

(Continued)

7 15

Maintenance

(Continued) (cid:129) Turn the engine off and wait until it cools down. Use extreme care when removing the radiator cap. Wrap a thick towel around it, and turn it counterclockwise slowly to the first stop. Step back while the pressure is released from the cooling system. When you are sure all the pres- sure has been released, press down on the cap, using a thick towel, and continue turning coun- terclockwise to remove it.

(cid:129) Even if the engine is not operat- ing, do not remove the radiator cap or the drain plug while the engine and radiator are hot. Hot coolant and steam may still blow out under pressure, causing seri- ous injury.

WARNING The electric motor (cooling fan) is con- by trolled engine temperature, coolant refrigerant pressure It may some- and vehicle speed. times operate even when the engine is not running. Use extreme caution when working near the blades of the cooling fan so that you are not injured by a rotating fan blades. As the engine coolant tem- perature decreases, the electric motor will automatically shut off. This is a normal condition.

16

level should be

OXM079006
Check the condition and connections of all cooling system hoses and heater hoses. Replace any swollen or deterio- rated hoses. The coolant filled between F (MAX) and L (MIN) marks on the side of the coolant reservoir when the engine is cool. If the coolant level is low, add enough deonized water or soft water. Bring the level to F (MAX), but do not overfill. If fre- quent coolant refill is required, see an authorized HYUNDAI dealer for a cooling system inspection.

G070101BUN Recommended engine coolant (cid:129) When adding coolant, use only deion- ized water or soft water for your vehicle and never mix hard water in the coolant filled at the factory. An improp- er coolant mixture can result in serious malfunction or engine damage.

(cid:129) The engine in your vehicle has alu- minum engine parts and must be pro- tected by an ethylene-glycol-based coolant to prevent corrosion and freez- ing.

(cid:129) DO NOT USE alcohol or methanol coolant or mix them with the specified coolant.

(cid:129) Do not use a solution that contains more than 60% antifreeze or less than 35% antifreeze, which would reduce the effectiveness of the solution.

For mixture percentage, refer to the fol- lowing table.

Ambient

Temperature

5°F (-15°C) -13°F (-25°C) -31°F (-35°C) -49°F (-45°C)

Mixture Percentage

(volume)

Antifreeze

Water

35
40
50
60

65
60
50
40

OCM070007

WARNING

Radiator cap

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot coolant and steam may blow out under pres- sure causing serious injury.

Maintenance

G070200AFD Changing the coolant Have coolant changed by an authorized HYUNDAI dealer according the Maintenance Schedule at the beginning of this section.

to

CAUTION

Put a thick cloth or fabric around the radiator cap before refilling the coolant in order to prevent the coolant from overflowing into engine parts such as generator.

WARNING - Coolant

(cid:129) Do not use radiator coolant or antifreeze in the washer fluid reservoir.

(cid:129) Radiator coolant can severely obscure visibility when sprayed on the windshield and may cause loss of vehicle control or damage to paint and body trim.

7 17

Maintenance

BRAKE FLUID

OXM079008

G080100AXM Checking the brake fluid level Check the fluid level in the reservoir peri- odically. The level should be between MAX and MIN marks on the side of the reservoir.

fluid

Before removing the reservoir cap and adding brake fluid, clean the area around the reservoir cap thoroughly to prevent brake fluid contamination. If the level is low, add fluid to the MAX level. The level will fall with accumulated mileage. This is a normal condition asso- ciated with the wear of the brake linings. If the fluid level is excessively low, have the brake system checked by an author- ized HYUNDAI dealer.

Use only the specified brake fluid.(Refer to “Recommended lubricants and capac- ities”in section 8.)

Never mix different types of fluid.

WARNING - Loss of brake

fluid

In the event the brake system requires frequent additions of fluid, the vehicle should be inspected by an authorized HYUNDAI dealer.

WARNING - Brake fluid

When changing and adding brake fluid, handle it carefully. Do not let it come in contact with your eyes. If brake fluid should come in contact with your eyes, immediately flush them with a large quantity of fresh tap water. Have your eyes examined by a doctor as soon as possible.

CAUTION

Do not allow brake fluid to contact the vehicle's body paint, as paint damage will result. Brake fluid, which has been exposed to open air for an extended time should never be used as its quality cannot be guaranteed. It should be disposed of properly.Don't put in the wrong kind of fluid.A few drops of miner- al-based oil, such as engine oil, in your brake system can damage brake system parts.

18

POWER STEERING FLUID

Maintenance

✽✽ NOTICE Check that the fluid level is in the "HOT" range on the reservoir. If the fluid is cold, check that it is in the "COLD" range.

In the event the power steering system requires frequent addition of fluid, the vehicle should be inspected by an authorized HYUNDAI dealer.

Use only the specified power steering fluid.(Refer to "Recommended lubricants or capacities" in section 8.)

Checking the power steering hose Check the connections for oil leaks, dam- age and twists in the power steering hose before driving.

OCM070009
Checking the power steering fluid level With the vehicle on level ground, check the fluid level in the power steering reser- voir periodically. The fluid should be between MAX and MIN marks on the side of the reservoir at the normal tem- perature. Before adding power steering fluid, thor- oughly clean the area around the reser- voir cap to prevent power steering fluid contamination. If the level is low, add fluid to the MAX level.

CAUTION

(cid:129) To avoid damage to the power steering pump,do not operate the vehicle for prolonged periods with a low power steering fluid level.

(cid:129) Never start the engine when the

reservoir tank is empty.

(cid:129) When adding fluid,be careful that

dirt does not get into the tank.

(cid:129) Too little fluid can result in increased steering effort and/or noise from the power steering system.

(cid:129) The use of the non-specified fluid could reduce the effectiveness of the power steering system and cause damage to it.

7 19

Maintenance

WASHER FLUID

OCM070010

G120100AUN Checking the washer fluid level The reservoir is translucent so that you can check the level with a quick visual inspection. Check the fluid level in the washer fluid reservoir and add fluid if necessary. Plain water may be used if washer fluid is not available. However, use washer solvent with antifreeze characteristics in cold cli- mates to prevent freezing.

20

WARNING - Coolant

(cid:129) Do not use radiator coolant or antifreeze in the washer fluid reservoir.

(cid:129) Radiator coolant can severely obscure visibility when sprayed on the windshield and may cause loss of vehicle control or damage to paint and body trim.

(cid:129) Windshield Washer fluid agents contain some amounts of alcohol and can be flammable under cer- tain circumstances. Do not allow sparks or flame to contact the washer fluid or the washer fluid reservoir. Damage to the vehicle or occupants could occur.

(cid:129) Windshield washer fluid is poi- sonous to humans and animals. Do not drink and avoid contact- ing windshield washer fluid. Serious injury or death could occur.

PARKING BRAKE

Maintenance

OCM050015

OCM050019

Checking the parking brake Type A Check whether the stroke is within spec- ification when the parking brake pedal is depressed with 66 lb (30 kg, 294 N) of force. Also, the parking brake alone should securely hold the vehicle on a fairly steep grade. If the stroke is more or less than specified, have the parking brake adjusted by an authorized HYUNDAI dealer.

Stroke : 8~9 notch

Type B Check the stroke of the parking brake by counting the number of “clicks’’ heard while fully applying it from the released position. Also, the parking brake alone should securely hold the vehicle on a fair- ly steep grade. If the stroke is more or less than specified, have the parking brake adjusted by an authorized HYUNDAI dealer.

Stroke : 5~6 “clicks’’ at a force of

44 lbs (20 kg, 196 N).

7 21

Maintenance

AIR CLEANER

OXM079012

G160100ACM Filter replacement It must be replaced when necessary, and should not be washed. You can clean the filter when inspecting the air cleaner element. Clean the filter by using compressed air.

OXM079013
1. Loosen the air cleaner cover attaching

clips and open the cover.

OXM079014

2. Wipe the inside of the air cleaner. 3. Replace the air cleaner filter. 4. Lock the cover with the cover attaching

clips.

5. Verify that the air cleaner cover is properly attached at all four corners and sealing against air cleaner.

22

Replace the filter according to the Maintenance Schedule. If the vehicle is operated in extremely dusty or sandy areas, replace the ele- ment more often than the usual recom- mended intervals.(Refer to “Maintenance under severe usage conditions” in this section.)

CAUTION

(cid:129) Do not drive with the air cleaner removed;this will result in exces- sive engine wear.

(cid:129) When removing the air cleaner fil- ter, be careful that dust or dirt does not enter the air intake, or damage may result.

(cid:129) Use a HYUNDAI genuine part.Use of nongenuine part could damage the air flow sensor.

Maintenance

7 23

Maintenance

CLIMATE CONTROL AIR FILTER (IF EQUIPPED) G170100AXM Filter inspection If the vehicle is operated in the severely air-polluted cities or on dusty rough roads for a long period, it should be inspected more frequently and replaced earlier. When you, the owner, replace the climate control air filter, replace it per- forming the following procedure, and be careful to avoid damaging other compo- nents. Replace the filter according to the main- tenance Schedule.

Filter replacement 1. Open the glove box and remove the

support strap (1).

OCM070015

OCM070016
2. With the glove box open, remove the

stoppers on both sides.

24

OCM055011
3. Remove the climate control air filter case by pulling out both sides of the cover.

OCM070017

4. Replace the climate control air filter. 5. Reassemble in the reverse order of

disassembly.

✽✽ NOTICE When replacing the climate control air filter install it properly. Otherwise, the system may produce noise and the effec- tiveness of the filter may be reduced.

Maintenance

7 25

Maintenance

WIPER BLADES

Contamination of either the windshield or the wiper blades with foreign matter can reduce the effectiveness of the wind- shield wipers. Common sources of con- tamination are insects, tree sap, and hot wax treatments used by some commer- cial car washes. If the blades are not wip- ing properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.

G180200AUN Blade replacement When the wipers no longer clean ade- quately, the blades may be worn or cracked, and require replacement.

CAUTION

To prevent damage to the wiper arms or other components, do not attempt to move the wipers manual- ly.

1JBA5122

CAUTION

G180100AUN Blade inspection ✽✽ NOTICE Commercial hot waxes applied by auto- matic car washes have been known to make the windshield difficult to clean.

To prevent damage to the wiper blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them.

CAUTION

The use of a non-specified wiper blade could result in wiper malfunc- tion and failure.

26

Maintenance

1JBA7037
2. Compress the clip and slide the blade

assembly downward.

1JBA7038

3. Lift it off the arm. 4. Install the blade assembly in the

reverse order of removal.

1LDA5023

Front windshield wiper blade 1. Raise the wiper arm and turn the wiper blade assembly to expose the plastic locking clip.

CAUTION

Do not allow the wiper arm to fall against the windshield,since it may chip or crack the windshield.

7 27

Maintenance

OHM078062

G180202AFD Rear window wiper blade 1. Raise the wiper arm and pull out the

wiper blade assembly.

OHM078063
2. Install the new blade assembly by inserting the center part into the slot in the wiper arm until it clicks into place. 3. Make sure the blade assembly is installed firmly by trying to pull it slight- ly.

To prevent damage to the wiper arms or other components, have an authorized HYUNDAI dealer replace the wiper blade.

28

BATTERY

OCM070019

G190100CUN For best battery service (cid:129) Keep the battery securely mounted. (cid:129) Keep the battery top clean and dry. (cid:129) Keep the terminals and connections clean, tight, and coated with petroleum jelly or terminal grease.

(cid:129) Rinse any spilled electrolyte from the battery immediately with a solution of water and baking soda.

(cid:129) If the vehicle is not going to be used for an extended time, disconnect the bat- tery cables.

WARNING - Battery dangers

Always read the following instructions carefully when handling a battery. Keep lighted cigarettes and all other flames or sparks away from the battery. Hydrogen, a highly com- bustible gas, is always present in battery cells and may explode if ignited. Keep batteries out of the reach of children because batteries contain highly corrosive SULFURIC ACID. Do not allow battery acid to contact your skin, eyes, clothing or paint finish.

(Continued)

Maintenance

(Continued)

If any electrolyte gets into your eyes, flush your eyes with clean water for at least 15 minutes and get immedi- ate medical attention. If electrolyte gets on your skin, thoroughly wash the contacted area. If you feel a pain or a burning sensa- tion, get medical attention immediately. Wear eye protection when charging or working near a battery. Always provide ventilation when working in an enclosed space. An inappropriately disposed battery can be harmful to the environment and human health. Dispose the battery according to your local law(s) or regulation.

(Continued)

7 29

Maintenance

(Continued) (cid:129) When lifting a plastic-cased bat- tery, excessive pressure on the case may cause battery acid to leak, resulting in personal injury. Lift with a battery carrier or with your hands on opposite corners. (cid:129) Never attempt to recharge the battery when the battery cables are connected.

(cid:129) The electrical ignition system works with high voltage. Never touch these components with the engine running or the ignition switched on.

Failure to follow the above warn- ings can result in serious bodily injury or death.

G190200AUN Battery recharging Your vehicle has a maintenance-free, calcium-based battery. (cid:129) If the battery becomes discharged in a short time (because, for example, the headlights or interior lights were left on while the vehicle was not in use), recharge it by slow charging (trickle) for 10 hours.

(cid:129) If the battery gradually discharges because of high electric load while the vehicle is being used, recharge it at 20- 30A for two hours.

CALIFORNIA PROPOSITION 65 WARNING Battery posts, terminals, and relat- ed accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer, birth defects, and reproduc- tive harm. Batteries also contain other chemicals known to the State of California to cause cancer. Wash hands after handling.

CAUTION

(cid:129) Always charge the battery fully to prevent battery case damage in low temperature area.

(cid:129) If you connect unauthorized elec- tronic devices to the battery, the battery may discharge.Never use unauthorized devices.

30

(Continued) (cid:129) Before performing maintenance or recharging the battery, turn off all accessories and stop the engine.

(cid:129) The negative battery cable must be removed first and installed last when the battery is discon- nected.

Maintenance

G130300AUN Reset items Items should be reset after the battery has been discharged or the battery has been disconnected. (cid:129) Auto up/down window (See section 4) (cid:129) Sunroof (See section 4) (cid:129) Trip computer (See section 4) (cid:129) Climate control system

(See section 4)

(cid:129) Clock (See section 4) (cid:129) Audio (See section 4)

WARNING - Recharging

battery

recharging

When the battery, observe the following precautions: (cid:129) The battery must be removed from the vehicle and placed in an area with good ventilation.

(cid:129) Do not allow cigarettes, sparks,

or flame near the battery.

(cid:129) Watch the battery during charg- ing, and stop or reduce the charg- ing rate if the battery cells begin gassing (boiling) violently or if the temperature of the electrolyte of any cell exceeds 120°F (49°C). (cid:129) Wear eye protection when check-

ing the battery during charging.

(cid:129) Disconnect the battery charger in

the following order. 1. Turn off the battery charger

main switch.

2. Unhook the negative clamp from the negative battery ter- minal.

3. Unhook the positive clamp from the positive battery termi- nal.

(Continued)

7 31

WARNING - Tire underin-

flation

Severe underinflation (10 psi (70 kPa) or more) can lead to severe heat build-up, causing blowouts, tread separation and other tire failures that can result in the loss of vehicle control leading to severe injury or death. This risk is much higher on hot days and when driving for long periods at high speeds.

Maintenance

TIRES AND WHEELS G200100AUN Tire care For proper maintenance, safety, and maximum fuel economy, you must always maintain recommended tire inflation pressures and stay within the load limits and weight distribution recommended for your vehicle.

G200200ACM Recommended cold tire inflation pressures All tire pressures (including the spare) should be checked when the tires are cold. “Cold Tires” means the vehicle has not been driven for at least three hours or driven less than 1 mile (1.6 km). Recommended pressures must be maintained for the best ride, top vehi- cle handling, and minimum tire wear. For recommended inflation pressure refer to “Tire and wheels” in section 8.

32

OCM070048L All specifications (sizes and pres- sures) can be found on a label attached to the vehicle.

CAUTION

(cid:129) Underinflation also results in excessive wear,poor handling and reduced fuel economy. Wheel deformation also is possible.Keep your tire pres- sures at the proper levels.If a tire frequently needs refilling, have it checked by an author- ized HYUNDAI dealer.

(cid:129) Overinflation produces a harsh ride, excessive wear at the center of the tire tread,and a greater possibility of dam- age from road hazards.

CAUTION

(cid:129) Warm tires normally exceed recommended cold tire pres- sures by 4 to 6 psi (28 to 41
kPa). Do not release air from warm tires to adjust the pres- sure or the tires will be under- inflated.

(cid:129) Be sure to reinstall the tire inflation valve caps. Without the valve cap,dirt or moisture could get into the valve core and cause air leakage. If a valve cap is missing,install a new one as soon as possible.

WARNING - Tire inflation Overinflation or underinflation can reduce tire life, adversely affect vehicle handling, and lead to sudden tire failure. This could result in loss of vehicle control and potential injury.

Maintenance

CAUTION - Tire pressure Always observe the following: (cid:129) Check tire pressure when the tires are cold. (After vehicle has been parked for at least three hours or hasn't been driv- en more than 1 mile (1.6 km) since startup.)

(cid:129) Check the pressure of your spare tire each time you check the pressure of other tires.

(cid:129) Never overload your vehicle. Be careful not to overload a vehicle luggage rack if your vehicle is equipped with one. (cid:129) Worn,old tires can cause acci- dents. If your tread is badly worn, or if your tires have been damaged,replace them.

7 33

Maintenance

G200300AUN Checking tire inflation pressure Check your tires once a month or more. Also, check the tire pressure of the spare tire.

G200301AFD How to check Use a good quality gage to check tire pressure. You can not tell if your tires are properly inflated simply by look- ing at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km).

Remove the valve cap from the tire valve stem. Press the tire gage firm- ly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended pressure on the tire and loading information label, no further adjust- ment is necessary. If the pressure is low, add air until you reach the rec- ommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gage. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and mois- ture.

WARNING

(cid:129) Inspect your tires frequently for proper inflation as well as wear and damage. Always use a tire pressure gauge.

(cid:129) Tires with too much or too little pressure wear unevenly caus- ing poor handling, loss of vehi- cle control, and sudden tire failure leading to accidents, injuries, and even death. The recommended cold tire pres- sure for your vehicle can be found in this manual and on the tire label located on the dri- ver's side center pillar.

(cid:129) Worn tires can cause acci- dents. Replace tires that are worn, show uneven wear, or are damaged.

(cid:129) Remember to check the pres- sure of your spare tire. HYUNDAI recommends that you check the spare every time you check the pressure of the other tires on your vehi- cle.

34

G200400AXM Tire rotation To equalize tread wear, it is recom- mended that the tires be rotated every 7,500 miles (12,000 km) or sooner if irregular wear develops. During rotation, check the tires for correct balance. When rotating tires, check for uneven wear and damage. Abnormal wear is usually caused by incorrect tire pres- sure, improper wheel alignment, out- of-balance wheels, severe braking or severe cornering. Look for bumps or bulges in the tread or side of tire. Replace the tire if you find either of these conditions. Replace the tire if fabric or cord is visible. After rotation, be sure to bring the front and rear tire pressures to specification and check lug nut tightness. Refer to “Tire and wheels” in section 8.

With a full-size spare tire (if equipped)

Without a spare tire

S2BLA790

Maintenance

Disc brake pads should be inspected for wear whenever tires are rotated.

✽✽ NOTICE Rotate radial tires that have an asymmetric tread pattern only from front to rear and not from right to left.

WARNING

(cid:129) Do not use the compact spare

tire for tire rotation.

Directional tires (if equipped)

S2BLA790A

(cid:129) Do not mix bias ply and radial ply tires under any circum- stances. This may cause unusual handling characteris- tics that could result in death, severe injury, or property damage.

CBGQ0707A

7 35

Maintenance

G200500AUN Wheel alignment and tire balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. In most cases, you will not need to have your wheels aligned again. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced.

CAUTION

Improper wheel weights can damage your vehicle's alu- minum wheels. Use only approved wheel weights.

36

Tread wear indicator

OEN076053

G200600BFD Tire replacement If the tire is worn evenly, a tread wear indicator will appear as a solid band across the tread. This shows there is less than 1/16 in. (1.6 mm) of tread left on the tire. Replace the tire when this happens. Do not wait for the band to appear across the entire tread before replac- ing the tire.

WARNING - Replacing

tires

(cid:129) Driving on worn-out tires is very hazardous and will reduce braking effectiveness, steering accuracy, and trac- tion.

(cid:129) Your vehicle is equipped with tires designed to provide for safe ride and handling capa- bility. Do not use a size and type of tire and wheel that is different from the one that is originally installed on your vehicle. It can affect the safety and performance of your vehi- cle, which could lead to han- dling failure or rollover and serious injury. When replacing the tires, be sure to equip all four tires with the tire and wheel of the same size, type, tread, brand and load-carrying capacity.

(Continued)

G200601AUN Compact spare tire replacement (if equipped) A compact spare tire has a shorter tread life than a regular size tire. Replace it when you can see the tread wear indicator bars on the tire. The replacement compact spare tire should be the same size and design tire as the one provided with your new vehicle and should be mounted on the same compact spare tire wheel. The compact spare tire is not designed to be mounted on a regular size wheel, and the compact spare tire wheel is not designed for mount- ing a regular size tire.

(Continued) (cid:129) The use of any other tire size or type may seriously affect ride, handling, ground clear- ance, stopping distance, body to tire clearance, snow tire clearance, and speedometer reliability.

(cid:129) It is best to replace all four tires at the same time. If that is not possible, or necessary, then replace the two front or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.

(cid:129) The ABS works by comparing the speed of the wheels. Tire size can affect wheel speed. When replacing tires, all 4 tires must use the same size origi- nally supplied with the vehicle. Using tires of a different size can cause the ABS (Anti-lock Brake System) and ESC (Electronic Stability Control), to work irregularly.

Maintenance

G200700AUN Wheel replacement When replacing the metal wheels for any reason, make sure the new wheels are equivalent to the original factory units in diameter, rim width and offset.

WARNING

A wheel that is not the correct size may adversely affect wheel and bearing life, braking and stopping abilities, handling characteristics, ground clear- ance, body-to-tire clearance, snow clearance, speedometer and odometer cal- ibration, headlight aim and bumper height.

chain

7 37

Maintenance

G200800AUN Tire traction Tire traction can be reduced if you drive on worn tires, tires that are improperly inflated or on slippery road surfaces. Tires should be replaced when tread wear indicators appear. To reduce the possibility of losing control, slow down whenever there is rain, snow or ice on the road.

G200900AUN Tire maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment. When you have new tires installed, make sure they are balanced. This will increase vehicle ride comfort and tire life. Additionally, a tire should always be rebalanced if it is removed from the wheel.

38

5,6

I030B04JM

information

G201000AUN Tire sidewall labeling identifies and This describes the fundamental charac- teristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

G201001AUN 1.Manufacturer or brand name Manufacturer or Brand name is shown.

G201002ACM 2.Tire size designation A tire’s sidewall is marked with a tire size designation. You will need this information when selecting replace- ment tires for your car. The following explains what the letters and num- bers in the tire size designation mean. Example tire size designation: (These numbers are provided as an example only; your tire size designa- tor could vary depending on your vehicle.) P235/60R18 102H

P - Applicable vehicle type (tires marked with the prefix “P’’ are intended for use on passenger vehicles or light trucks; however, not all tires have this marking).

235 - Tire width in millimeters. 60 - Aspect ratio. The tire’s section height as a percentage of its width.

R - Tire construction code (Radial). 18 - Rim diameter in inches.

102 - Load Index, a numerical code associated with the maximum load the tire can carry.

H - Speed Rating Symbol. See the speed rating chart in this section for additional information.

Wheel size designation Wheels are also marked with impor- tant information that you need if you ever have to replace one. The follow- ing explains what the letters and numbers in the wheel size designa- tion mean.

Example wheel size designation: 7.0JX18

7.0 - Rim width in inches. J - Rim contour designation. 18 - Rim diameter in inches.

Tire speed ratings The chart below lists many of the dif- ferent speed ratings currently being used for passenger car tires. The speed rating is part of the tire size designation on the sidewall of the tire. This symbol corresponds to that tire's designed maximum safe oper- ating speed.

Speed Rating Symbol

Maximum Speed

112 mph (180 km/h)

118 mph (190 km/h)

130 mph (210 km/h)

149 mph (240 km/h)

Above 149 mph (240 km/h)

Maintenance

G201003AEN 3.Checking tire life

(TIN :Tire Identification Number)

Any tires that are over 6 years old, based on the manufacturing date (including the spare tire) should be replaced by new ones. You can find the manufacturing date on the tire sidewall (possibly on the inside of the wheel), displaying the DOT Code. The DOT Code is a series of num- bers on a tire consisting of numbers and English letters. The manufactur- ing date is designated by the last four digits (characters) of the DOT code.

DOT : XXXX XXXX OOOO The front part of the DOT means a plant code number, tire size and tread pattern and the last four num- bers indicate week and year manu- factured. For example: DOT XXXX XXXX 1611 represents that the tire was produced in the 16th week of 2011.

7 39

Maintenance

WARNING - Tire age

Tires degrade over time, even when they are not being used. Regardless of the remaining tread, it is recommended that tires generally be replaced after six (6) years of normal service. Heat caused by not climates or frequent high loading condi- tions can accelerate the aging process. Failure to follow this Warning can result in sudden tire failure, which could lead to a loss of control and an acci- dent involving serious injury or death.

G201004AUN 4.Tire ply composition and material The number of layers or plies of rub- ber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. The letter "R" means radial ply con- struction; the letter "D" means diago- nal or bias ply construction; and the letter "B" means belted-bias ply con- struction.

40

G201005AUN 5.Maximum permissible inflation

pressure

This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure. Refer to the Tire and Loading Information label inflation pressure.

for recommended

G201006AUN 6.Maximum load rating This number indicates the maximum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire.

the

G201007BUN 7.Uniform tire quality grading Quality grades can be found where applicable on tire sidewall between tread shoulder and maxi- mum section width. For example: TREADWEAR 200 TRACTION AA TEMPERATURE A

Tread wear The tread wear grade is a compara- tive rating based on the wear rate of the tire when tested under controlled conditions on a specified govern- ment test course. For example, a tire graded 150 would wear one-and-a- half times (1½) as well on the gov- ernment course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm because of variations in driving habits, service practices and differ- ences in road characteristics and cli- mate. These grades are molded on the side-walls of passenger vehicle tires. The tires available as standard or optional equipment on your vehicle may vary with respect to grade.

Traction - AA, A, B & C The traction grades, from highest to lowest, are AA, A, B and C. Those grades represent the tires ability to stop on wet pavement as measured under controlled conditions on spec- ified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perform- ance.

WARNING

The traction grade assigned to this tire is based on straight- ahead braking traction tests, and does not include accelera- tion, cornering, hydroplaning, or peak traction characteristics.

Temperature -A, B & C The temperature grades are A (the highest), B and C representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled condi- tions on a specified indoor laboratory test wheel.

Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The Grade C cor- responds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard NO. 109. Grades B and A represent higher levels of performance on the labora- tory test wheel than the minimum required by the law.

WARNING - Tire

temperature

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat build-up and possible sudden tire failure. This can cause loss of vehicle control and serious injury or death.

Maintenance

G201100AEN Tire terminology and definitions Air Pressure: The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in pounds per square inch (psi) or kilo- pascal (kPa). Accessory Weight: This means the combined weight of optional acces- sories. Some examples of optional accessories are, automatic transaxle power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.

7 41

Maintenance

Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilo- pascals (kPa) before a tire has built up heat from driving. Curb Weight: This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation motor vehicle safety standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric des- ignator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating GAWR FRT: Gross Axle Weight Rating for the Front Axle. GAWR RR: Gross Axle Weight Rating for the Rear axle.

42

Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Load Index: An assigned number ranging from 1 to 279 that corre- sponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maxi- mum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum per- missible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150
pounds (68 kg).

Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a par- ticular side that faces outward when mounted on a vehicle. The outward facing sidewall bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the inner facing sidewall. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommend- ed tire inflation pressure and shown on the tire placard. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seat- ed. Sidewall: The portion of a tire between the tread and the bead.

Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a tire when only 2/32 inch of tread remains. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire's traction, tempera- ture and treadwear. Ratings are determined by tire manufacturers using government testing proce- dures. The ratings are molded into the sidewall of the tire. Vehicle Capacity Weight: The num- ber of designated seating positions multiplied by 150 lbs. (68 kg) plus the rated cargo and luggage load.

Vehicle Maximum Load on the Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight. Vehicle Normal Load on the Tire: Load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occu- pant weight and dividing by 2. Vehicle Placard: A label permanent- ly attached to a vehicle showing the original equipment tire size and rec- ommended inflation pressure.

All season tires HYUNDAI specifies all season tires on some models to provide good performance for use all year round, including snowy and icy road condi- tions. All season tires are identified by ALL SEASON and/or M+S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than all season tires and may be more appropriate in some areas.

Maintenance

Summer tires HYUNDAI specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially reduced in snow and ice. Summer tires do not have the tire traction rat- ing M+S (Mud and Snow) on the tire side wall. if you plan to operate your vehicle in snowy or icy conditions. HYUNDAI recommends the use of snow tires or all season tires on all four wheels.

Snow tires If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; other- wise, poor handling may result. Snow tires should carry 4 psi (28
kPa) more air pressure than the pressure recommended for the stan- dard tires on the tire label on the dri- ver's side of the center pillar, or up to the maximum pressure shown on the tire sidewall, whichever is less.

7 43

Maintenance

Do not drive faster than 75 mph (120
km/h) when your car is equipped with snow tires.

Tire chains Tire chains, if necessary, should be installed on the drive wheels as fol- lows. 2WD : Front wheels AWD : All four wheels

If a full set of chains is not available for a AWD vehicle, chains may be installed on the front wheels only.

Be sure that the chains are installed in accordance with the manufactur- er's instructions. To minimize tire and chain wear, do not continue to use tire chains when they are no longer needed.

WARNING - Snow or ice

(cid:129) When driving on roads cov- ered with snow or ice, drive at less than 20 mph (30 km/h).

(cid:129) Use the SAE “S” class or wire

chains.

(cid:129) If you hear noise caused by chains contacting the body, retighten the chain to avoid contact with the vehicle body. (cid:129) To prevent body damage, retighten the chains after driv- ing 0.3~0.6 miles (0.5~1.0 km). (cid:129) Do not use tire chains on vehicles equipped with alu- minum wheels. In unavoid- able circumstance, use a wire type chain.

(cid:129) Use wire chains less than 0.59
inches (15mm) to prevent damage to the chain’s con- nection.

44

Radial-ply tires Radial-ply tires provide improved tread life, road hazard resistance and smoother high speed ride. The radi- al-ply tires used on this vehicle are of belted construction, and are selected to complement the ride and handling characteristics of your vehicle. Radial-ply tires have the same load carrying capacity, as bias-ply or bias belted tires of the same size, and use the same recommended inflation pressure. Mixing of radial-ply tires with bias-ply or bias belted tires is not recommended. Any combina- tions of radial-ply and bias-ply or bias belted tires when used on the same vehicle will seriously deteriorate vehicle handling. The best rule to fol- low is: Identical radial-ply tires should always be used as a set of four. Longer wearing tires can be more susceptible to irregular tread wear. It is very important to follow the tire rotation interval shown in this section to achieve the tread life potential of these tires. Cuts and punctures in radial-ply tires are repairable only in the tread area, because of sidewall flexing. Consult your tire dealer for radial-ply tire repairs.

Maintenance

This vehicle has 2 fuse panels, one locat- ed in the driver’s side panel bolster, the other in the engine compartment near the battery. If any of your vehicle’s lights, acces- sories, or controls do not work, check the appropriate circuit fuse. If a fuse has blown, the element inside the fuse will be melted. If the electrical system does not work, first check the driver’s side fuse panel. Always replace a blown fuse with one of the same rating. If the replacement fuse blows, this indi- cates an electrical problem. Avoid using the system involved and immediately consult an authorized HYUNDAI dealer. Three kinds of fuses are used:blade type for lower amperage rating, cartridge type, and fusible link for higher amperage rat- ings.

WARNING - Fuse replace-

ment

(cid:129) Never replace a fuse with any- thing but another fuse of the same rating.

(cid:129) A higher capacity fuse could cause damage and possibly a fire.

(cid:129) Never install a wire or aluminum foil instead of the proper fuse - even as a temporary repair. It may cause extensive wiring damage and a possible fire.

CAUTION

Do not use a screwdriver or any other metal object to remove fuses because it may cause a short circuit and damage the system.

FUSES Blade type

Normal

Blown

Cartridge type

Normal

Blown

Fusible link

Normal

Blown

1VQA4037

G210000AFD A vehicle’s electrical system is protected from electrical overload damage by fuses.

7 45

Maintenance

If the headlights or other electrical com- ponents do not work and the fuses are OK, check the fuse block in the engine compartment. If a fuse is blown, it must be replaced.

OCM054002

G210100AUN Inner panel fuse replacement 1. Turn the ignition switch and all other

switches off.

2. Open the fuse panel cover.

OCM070021
3. Pull the suspected fuse straight out. Use the removal tool provided in the engine compartment fuse panel.

4. Check the removed fuse; replace it if it

is blown.

5. Push in a new fuse of the same rating, and make sure it fits tightly in the clips. If it fits loosely, consult an authorized HYUNDAI dealer. If you do not have a spare, use a fuse of the same rating from a circuit you may not need for operating the vehicle, such as the cigar lighter fuse.

46

✽✽ NOTICE • If the memory fuse is pulled up from the fuse panel, the warning chime, audio, clock and interior lamps, etc., will not operate. Some items must be reset after replacement. Refer to “Battery” in this section.

• Even though the memory fuse is pulled up, the battery can still be dis- charged by operation of the head- lights or other electrical devices.

Maintenance

OCM070023

G210200AFD Engine compartment panel fuse replacement 1. Turn the ignition switch and all other

switches off.

2. Remove the fuse box cover by press-

ing the tap and pulling up.

7 47

OCM070022

G210101AXM Memory fuse (SHUNT connector) Your vehicle is equipped with a memory fuse (SHUNT connector) to prevent bat- tery discharge if your vehicle is parked without being operated for prolonged periods. Use the following procedures before parking the vehicle for prolonged periods. 1. Turn off the engine. 2. Turn off the headlights and tail lights. 3. Open the driver’s side panel cover and pull out the memory fuse (SHUNT connector).

✽✽ NOTICE If the main fuse is blown, consult an Authorized HYUNDAI Dealer.

Maintenance

3. Check the removed fuse; replace it if it is blown. To remove or insert the fuse, use the fuse puller in the engine com- partment fuse panel.

4. Push in a new fuse of the same rating, and make sure it fits tightly in the clips. If it fits loosely, consult an authorized HYUNDAI dealer.

CAUTION

After checking the fuse box in the engine compartment, securely install the fuse box cover. If not, electrical failures may occur from water leaking in.

48

OCM070025

G210201ACM Main fuse If the main fuse is blown, it must be removed as follows: 1. Disconnect the negative battery cable. 2. Remove the bolts shown in the picture

above.

3. Replace the fuse with a new one of the

same rating.

4. Reinstall in the reverse order of

removal.

G210300AFD Fuse/Relay panel description Inside the fuse/relay box covers, you can find the fuse/relay label describing fuse/relay name and capacity.

Driver’s side panel

Engine compartment

✽✽ NOTICE Not all fuse panel descriptions in this manual may be applicable to your vehi- cle. It is accurate at the time of printing. When you inspect the fuse box on your vehicle, refer to the fuse box label.

Maintenance

OCM070026/OCM070027

7 49

Maintenance

Driver's side fuse panel

Description

Fuse rating

START

P/WDW LH P/WDW RH

S/ROOF P/SEAT

SAFETY PWR

MIRR HTD A/BAG 2
A/BAG 1

ROOM LP

A/CON

AC INVERTER

P/AMP

P/OUTLET CTR

P/OUTLET C/LIGHTER

DR LOCK

A/BAG IND

ESC SW

50

10A 25A 25A 20A 30A 25A 10A 15A 15A

10A

10A

25A 30A 15A 25A 15A

20A

10A

10A

Protected component

Burglar Alarm Relay Power Window Main Switch, Rear Power Window Switch LH Power Window Main Switch, Passenger Power Window Switch, Rear Power Window Switch RH Sunroof Motor Driver/Passenger Seat Manual Switch, Driver Lumbar Support Switch Safety Power Window Module Rear Defogger Switch, Driver/Passenger Power Outside Mirror Digital Clock & Telltail SRS Control Module, PODS Module Instrument Cluster (IND.), Driver/Passenger Door Lamp, MAP Lamp, Room Lamp, Cargo Lamp, Driver/Passenger Vanity Switch A/C Control Module, Cluster Ionizer, Incar Sensor, Sunroof Motor, Electro Chromic Mirror, Blower Relay, GM02 (Ground), Home Link AC Inverter Module Amp Center Power Outlet Front Power Outlet & Cigarette Lighter, Rear Power Outlet Front Power Outlet & Cigarette Lighter Door Lock/Unlock Relay, ICM Relay Box (Key Lock/Unlock Relay), BCM, Driver/Passenger Door Lock Actuator, Tail Gate Lock Actuator, Rear Door Lock Actuator LH/RH, GM01 (Ground) Instrument Cluster (IND.) ESC Switch, Steering Angle Sensor, ICM Relay Box (Sub Start Relay), Driver/Passenger Seat Warmer Control Module, Multifunction Switch (Remote Control)

Description

Fuse rating

Protected component

Maintenance

T/SIG

S/WARMER

DRL

HAZARD

RR WIPER A/CON SW

CLUSTER

BCM 1

RR A/CON

TPMS BCM 2

AUDIO 2

BLOWER STOP LP PDM 1
BCM 3
CLOCK AUDIO 1

ATM PDM 2
POWER CONNECTOR

10A 15A 15A

15A

15A 10A

10A

10A 15A 10A 10A

10A

30A 15A 20A 10A 15A 15A 10A 15A

Hazard Switch Driver/Passenger Seat Warmer Control Module ICM Relay Box (DRL Relay) Hazard Relay, Hazard Switch, BCM, Instrument Cluster (IND.), Multifunction Switch (Light), Rear Combination Lamp (OUT) LH/RH, Head Lamp LH/RH Rear Wiper Relay, Rear Wiper Motor, Multifunction Switch (Wiper) A/C Control Module Alternator, Instrument Cluster (IND.), BCM, A/V & Navigation Head Unit, Tire Pressure Monitoring Module, DVD Module BCM Not Used Tire Pressure Monitoring Module Rheostat, BCM, Instrument Cluster (MICOM), AC Inverter Switch, AC Inverter Module Audio, A/V & Navigation Head Unit, BCM, DVD Module, Digital Clock & Telltale, Power Outside Mirror Switch Blower Relay, Blower Motor, A/CON SW 10A Stop Lamp Switch Not Used BCM, Ignition Key ILL. & Door Warning Switch, Security Indicator A/C Control Module, Data Link Connector, Digital Clock & Telltail Audio, A/V & Navigation Head Unit, DVD Module Sport Mode Switch, Key Solenoid Not Used FUSE - ROOM LP 15A, CLOCK 15A, AUDIO 1 15A, BCM 3 10A

7 51

Maintenance

Engine compartment

Description

Fuse rating

Protected component

175A

30A 40A 40A 50A 20A 40A 40A 50A 40A

50A

40A 40A 15A 30A

15A 15A

FUSIBLE LINK - BLR, B+ 2, P/WDW, ESC 1, ESC 2 FUSE - DEICER, RR HTD, A/CON, FR FOG, H/LP LO LH, H/LP LO RH Trailer Power Outlet Ignition Switch (ACC, IG 1) Multipurpose Check Connector, ESC Control Module Condenser Fan Relay (High) ESC Control Module FUSE - BLOWER Power Window Relay, FUSE - SAFETY PWR FUSE - P/SEAT, TPMS, RR A/CON, S/WARMER, S/ROOF, PDM 2, P/AMP, AC INVERTER, DRL Ignition Switch (START, IG 2), Start Relay FUSE - DR LOCK, HAZARD, ATM, PDM 1, STOP LP, POWER CONNECTOR (BCM 3, CLOCK ROOM LP, AUDIO 1) Condenser Fan Relay (Low) Engine Control Relay Front Wiper Deicer Relay Rear Defogger Relay Head Lamp Low Relay (RH) Horn Relay

ALT

BATT IGN 1
ESC 1

CON FAN 2

ESC 2
BLR

P/WDW

B+ 2
IGN 2

B+ 1

CON FAN 1
ECU MAIN DEICER RR HTD

H/LP LO RH

HORN

52

Maintenance

Description

Fuse rating

Protected component

10
11
12
13

H/LP LO LH H/LP HI IND

A/CON

ATM

TAIL LP RH

FR FOG

15A 10A

10A 15A

10A 10A

Head Lamp Low Relay (LH) Instrument Cluster (High Beam IND.) A/CON Relay AWD ECM, PCM (G4KE), Back-Up Lamp Relay