Download PDF Manual

pre-tensioner seat belt.


WARNING:


o As its name implies, the SRS is designed to work with, and be supplemental to, the driver's and the passenger's three point seat belt systems and is not a substitute for them. Therefore, your seat belts must be worn at all times while the vehicle is in motion. The airbags deploy only in certain frontal impact conditions severe enough to cause significant in- jury to the vehicle occupants.


o Sitting too close to a front airbag can result in serious or fatal injury if the front airbags inflate. Always sit as far back from airbags as possible.


WARNING:


o Ignoring the SRS indicator light can re- sult in serious or fatal injury if the airbags, Occupant Classification® system or pre- tensioners do not work properly. Have your car checked by a dealer as soon as possible if the SRS warning light alerts you to a potential problem.


o The SRS is designed to deploy the front airbags only when an impact is suffi- ciently severe and when the impact angle is less than 30° from the forward longi- tudinal axis of the vehicle and will not deploy in side, rear or rollover impacts. Additionally, the airbags will only de- ploy once. Thus, seat belts must be worn at all times.


FEATURES OF YOUR HYUNDAI


33


WARNING:


o Front airbags are not intended to deploy in side-impact, rear-impact or rollover crashes. In addition, airbags will not deploy in frontal crashes below the de- ployment threshold.


Rear impact


Side Impact


Rollover


B240C01E o The driver should sit back as far as possible while still maintaining control of the vehicle. If you are sitting too close to the airbag, it can cause death or seri- ous injury when it inflates.


1 FEATURES OF YOUR HYUNDAI


34


WARNING:


WARNING:


o For maximum safety protection in all types of crashes, all occupants includ- ing the driver should always wear their seat belts whether or not an airbag is also provided at their seating position to minimize the risk of severe injury or death in the event of a crash. Do not sit or lean unnecessarily close to the airbag while the vehicle is in motion.


o Sitting improperly or out of position can result in serious or fatal injury in a crash. All occupants should sit upright in their seats with their feet on the floor until the vehicle is parked and the ignition key is removed.


o The SRS airbag system must deploy very rapidly to provide protection in a crash. If an occupant is out of position because of not wearing a seat belt, the airbag may forcefully contact the occupant causing serious or fatal injuries.


o No objects should be placed over or near the airbag modules on the steering wheel, instrument panel, and the front passenger's panel above the glove box, because any such object could cause harm if the vehicle is in a crash severe enough to cause the airbags to deploy. o If the airbags deploy, they must be re- placed by an authorized Hyundai dealer. o Do not tamper with or disconnect SRS wiring, or other components of the SRS system. Doing so could result in injury, due to accidental deployment of the airbags or by rendering the SRS inopera- tive.


o Do not install a child restraint system in the front passenger seat position. A child restraint system must never be placed in the front seat. The infant or child could be severely injured or killed by an airbag deployment in case of an accident.


o Do not allow children to ride in the front passenger seat. If older children (teen- agers and older) must ride in the front seat, make sure they are always properly belted and the seat is moved back as far as possible.


B240B01E-AAT SRS Components and Functions


2 710


11


7 9


B240B01E-1
The SRS consists of the following components:


1. Driver's Airbag Module 2. Passenger's Airbag Module 3. Knee Bolster 4. Pre-tensioner Seat Belt 5. Front Impact Sensor 6. Driver's and Front Passenger's Seat Belt


7. Driver's and Front Passenger's Seat Posi-


Usage Sensors


tion Sensors


8. SRS Service Reminder Indicator (SRI) 9. SRS Control Module (SRSCM) 10.Occupant Classification® System


(Front passenger's seat only) 11.Passenger Airbag Off Indicator


(Front passenger's seat only)


FEATURES OF YOUR HYUNDAI


35


B240B02L


Upon deployment, tear seams molded directly into the pad covers will separate under pres- sure from the expansion of the airbags. Further opening of the covers then allows full inflation of the airbags.


B240B03L A fully inflated airbag, in combination with a properly worn seat belt, slows the driver's or the passenger's forward motion, reducing the risk of head and chest injury.


After complete inflation, the airbag immediately starts deflating, enabling the driver to maintain forward visibility.


The SRSCM continually monitors all elements while the ignition is "ON" to determine if a frontal or near-frontal impact is severe enough to require airbag deployment or pre-tensioner seat belt deployment.


The SRS service reminder indicator (SRI) on the instrument panel will blink for about 6 sec- onds after the ignition key is turned to the "ON" position or after the engine is started, after which the SRI should go out.


B240B01L


The airbag modules are located both in the center of the steering wheel and in the front passenger's panel above the glove box. When the SRSCM detects a considerable impact to the front of the vehicle, it will automatically deploy the front airbags.


1 FEATURES OF YOUR HYUNDAI


36


Passenger's Airbag


Passenger's Airbag


B240B04E


B240B05L


CAUTION:


When installing a container of liquid air freshener inside the vehicle, do not place it near the instrument cluster nor on the in- strument panel surface. If there is any leak- age from the air freshener onto these areas (instrument cluster, instrument panel or air ventilator), it may damage these parts. If the liquid from the air freshener does leak onto these areas, wash them with water immedi- ately.


WARNING:


o When the SRS is activated, there may be a loud noise and fine dust will be re- leased throughout the vehicle. These conditions are normal and are not haz- ardous. However, the fine dust generat- ed during airbag deployment may cause skin irritation. Wash your hands and face thoroughly with lukewarm water and a mild soap after an accident in which the airbags were deployed.


WARNING:


o The SRS can function only when the ignition key is in the "ON" position. If the SRS SRI does not come on, or continu- ously remains on after flashing for about 6 seconds when the ignition key is turned to the "ON" position, or after the engine is started, comes on while driving, the SRS is not working properly. If this oc- curs, have your vehicle immediately in- spected by your Hyundai dealer.


o Before you replace a fuse or disconnect a battery terminal, turn the ignition key to the "LOCK" position or remove the ignition key. Never remove or replace the air bag related fuse(s) when the ignition key is in the "ON" position. Failure to heed this warning will cause the SRS SRI to illuminate.


If the front passenger seat is unoccupied or occupied by someone lighter than 56.4 pounds (25.6 kg), the indicator "PASSENGER AIR BAG OFF" will be displayed, and the front passenger's airbag will be turned off and will not deploy in frontal crashes.


NOTE: o The "Passenger Airbag Off" indicator illuminates for about 6 seconds after the ignition key is turned to the "ON" posi- tion or after the engine is started, and then turns off in a few seconds.


o If the "Passenger Airbag Off" indicator illuminates, the passenger's airbag will not deploy in frontal crashes. If the "Pas- senger Airbag Off" indicator does not illuminate, the passenger's airbag will deploy in frontal crashes.


o If your vehicle is equipped with side impact airbags, the front passenger's side impact airbag will not deploy when the telltale indicator is illuminated.


B990A01E-GAT OCCUPANT CLASSIFICATION® SYSTEM


The Occupant Classification® system detects the presence of a passenger in the front passenger's seat and will turn off the front passenger's airbag under certain conditions. The driver's airbag and the driver's side impact airbag are not connected with the Occupant Classification® system. The Occupant Classification® system is de- signed to detect the presence of a properly- seated occupant and determine if the passenger's airbag and the passenger's side impact airbag should be enabled (may inflate) or not.


HXDFL240-A


FEATURES OF YOUR HYUNDAI


37


CAUTION:


If the Occupant Classification® system is not working properly, the SRS airbag warn- ing light on the instrument panel will illuminate because the SRS airbag is con- nected with the Occupant Classification® system. If there is a malfunction of the Occupant Classification® system, the "Pas- senger Airbag Off" indicator will not illumi- nate and the front passenger's airbag will deploy in frontal crashes even if there is no occupant in the front passenger's seat. If the SRS airbag warning light does not illu- minate when the ignition key is turned to "ON" position, if it remains illuminated after blinking for approximately 6 seconds, or if it illuminates while the vehicle is being driven, have an authorized Hyundai dealer inspect the Occupant Classification sys- tem with SRS airbag system as soon as possible.


1 FEATURES OF YOUR HYUNDAI


38


WARNING:


o Even though your vehicle is equipped with the Occupant Classification® sys- tem, do not install a child restraint sys- tem in the front passenger's seat. A child restraint system must never be placed in the front seat. Children who are too large for child restraint systems should al- ways occupy the rear seat and use the available lap/shoulder belts. Children are afforded the most safety in the event of an accident when they are restrained by a proper restraint system in the rear seat. o The Occupant Classification® system can function only when the ignition key is in the "ON" position. If the "Passenger Airbag Off " indicator is illuminated when the front passenger's seat is occupied by an adult who is seated properly, (sit- ting upright with the seat in an upright position, centered on the seat cushion, with the person's legs comfortably ex- tended), or if the "Passenger Airbag Off" indicator is not illuminated when the front passenger's seat is unoccupied or occupied by someone lighter than 56.4
pounds(25.6 kg), the Occupant Classifi- cation® system is not working properly. If this occurs, have your vehicle immedi- ately inspected by your Hyundai dealer.


WARNING:


o If luggage or other objects are placed on the front passenger's seat or if the tem- perature of the seat changes, the "Passen- ger Airbag Off" indicator may blink. These conditions do not indicate a problem.


o If the "Passenger Airbag Off" indicator blinks continuously when an adult or a child heavier than 56.4 pounds(25.6 kg) sits in the front passenger seat and fas- tens the seat belt normally, have that person sit in the rear seat. If this occurs, have the Occupant Classification® sys- tem checked by an authorized Hyundai dealer as soon as possible.


o If you change the weight on the seat, the "Passenger Airbag Off" indicator may be turned on or off in a few seconds. This could result in the malfunction of the Occupant Classification® system.


o Do not modify or replace the front pas- senger seat. Don't place anything on or attach anything to the front passenger seat. These can adversely affect the Oc- cupant Classification® system.


o Do not sit on sharp objects such as tools when occupying the front passenger seat. These can adversely affect the occupant classification system.


o Do not use accessory seat covers on the


front seats.


B990B04Y-GAT Side Impact Airbag (If Installed)


B990B02Y


Your Hyundai is equipped with a side impact airbag in each front seat. The purpose of the airbag is to provide the vehicle's driver and/or front passenger with additional protection in a side impact than that offered by the seat belt alone. The side impact airbags are designed to deploy only during certain side impact colli- sions, depending on the crash severity, angle, speed and point of impact. The side impact airbags are not designed to deploy in all side impact situations.


FEATURES OF YOUR HYUNDAI


39


B240C01A-AAT SRS Care


o The SRS is virtually maintenance free and there are no parts you can safely service by yourself. The entire SRS system must be inspected by an authorized Hyundai dealer 10 years after the date that the vehicle was manufactured.


o Any work on the SRS system, such as removing, installing, repairing, or any work on the steering wheel or front seats must be performed by a qualified Hyundai technician. Improper handling of the airbag system may result in serious personal injury.


HSM393


WARNING:


o For best protection from the side impact airbag system and to avoid being injured by the deploying side impact airbag, both front seat occupants should sit in an upright position with their feet on the floor and the seat belt properly fastened. The driver's hands should be placed on the steering wheel at the 9:00 and 3:00
o'clock positions. The passenger's arms and hands should be placed on their laps.


o Do not use any accessory seat covers. o Use of seat covers could reduce or prevent


the effectiveness of the system.


o Do not install any accessories on the side


or near the side impact airbag.


o Do not use excessive force on the side of


the seat.


o Do not place any objects over the airbag or


between the airbag and yourself.


o Do not place any objects (an umbrella, bag, etc.) between the front door and the front seat. Such objects may become dan- gerous projectiles and cause injury if the supplemental side impact airbag inflates. o To prevent unexpected deployment of the side impact air bag that may result in personal injury, avoid impact to the side impact airbag sensor when the ignition key is on.


Side airbag sensor


B990B01E


WARNING:


o The side impact airbag is supplemental to the driver's and the passenger's seat belt systems and is not a substitute for them. Therefore your seat belts must be worn at all times while the vehicle is in motion. The airbags deploy only in cer- tain side impact conditions severe enough to cause significant injury to the vehicle occupants.


1 FEATURES OF YOUR HYUNDAI


40


WARNING:


o Do not install a child restraint system in


the front passenger seat position. A child restraint system must never be placed in the front seat. The infant or baby could be severely injured by an airbag deployment in case of an acci- dent.


o Modification to SRS components or wir- ing, including the addition of any kind of badges to the pad covers or modifica- tions to the body structure, can ad- versely affect SRS performance and lead to possible injury.


o For cleaning the airbag pad covers, use only a soft, dry cloth or one which has been moistened with plain water. Sol- vents or cleaners could adversely affect the airbag covers and proper deploy- ment of the system.


o No objects should be placed over or near the airbag modules on the steering wheel, instrument panel, and the front passenger's panel above the glove box, because any such object could cause harm if the vehicle is in a crash severe enough to cause the airbags to inflate. o If the airbags inflate, they must be re- placed by an authorized Hyundai dealer.


WARNING:


o Do not tamper with or disconnect SRS wiring, or other components of the SRS system. Doing so could result in injury, due to accidental firing of the airbags or by rendering the SRS inoperative.


o If components of the airbag system must be discarded, or if the vehicle must be scrapped, certain safety precautions must be observed. Your Hyundai dealer knows these precautions and can give you the necessary information. Failure to follow these precautions and proce- dures could increase the risk of personal injury.


o If you sell your vehicle, make certain that this manual is transferred to the new owner.


o If your car was flooded and has soaked carpeting or water on the floor, you shouldn't try to start the engine; have the car towed to an authorized Hyundai dealer.


INSTRUMENT CLUSTER AND INDICATOR


B260A03E-AAT (Without Trip Computer)


1 2 3


10 11 12


FEATURES OF YOUR HYUNDAI


41


13


14


15 16


17


18 19 20 21


22


23


B260A03E-A


1 FEATURES OF YOUR HYUNDAI


42


1. Trunk Lid (4 door)/Tail Gate (5 door) Open Warning Light 2. Traction Control Indicator Light (If installed) 3. ABS Warning Light (If installed) 4. Tachometer 5. Turn Signal Indicator Light 6. High Beam Indicator Light 7. Automatic Transaxle Position Indicator Light (Auto T/A only) 8. Front Fog Indicator Light (If installed) 9. Speedometer 10.Cruise Indicator Light (If installed) 11.Low Fuel Warning Light 12.Set Indicator Light (If installed)


13.Temperature Gauge 14.Door Ajar Warning Light 15.Seat Belt Warning Light 16.SRS (Airbag) Warning Light (If installed) 17.Odometer/Trip Odometer 18.Low Oil Pressure Warning Light 19.Charging System Warning Light 20.Parking Brake/Low Brake Fluid Level Warning Light 21.Malfunction Indicator Light (MIL) (If installed) 22.Trip Odometer Reset Switch 23.Fuel Gauge


B260B03E-AAT (With Trip Computer)


2 3


4 5 6


7 8


FEATURES OF YOUR HYUNDAI


43


10


11


12


1314


15


16


17


18


19


20


21


B260B03E-A


1 FEATURES OF YOUR HYUNDAI


44


1. Malfunction Indicator Light (MIL) (If installed) 2. SRS (Airbag) Warning Light (If installed) 3. Low Oil Pressure Warning Light 4. Turn Signal Indicator Light 5. Cruise Indicator Light (If installed) 6. Front Fog Indicator Light (If installed) 7. High Beam Indicator Light 8. Set Indicator Light (If installed) 9. Low Fuel Warning Light 10.Temperature Gauge 11.Tachometer


12.ABS Warning Light (If installed) 13.Charging System Warning Light 14.Seat Belt Warning Light 15.Trip Computer (If installed) 16.Trunk Lid (4 door)/Tail Gate (5 door) Open Warning Light 17.Door Ajar Warning Light 18.Parking Brake/Low Brake Fluid Level Warning Light 19.Traction Control Indicator Light (If installed) 20.Speedometer 21.Fuel Gauge


WARNING AND INDICATOR LIGHTS


B260B01A-AAT


B260P01E-GAT


B260D01A-AAT


FEATURES OF YOUR HYUNDAI


45


SRS (Airbag) Service Reminder Indicator (SRI)


ABS Service Reminder Indicator (SRI) (If installed)


The SRS service reminder indicator (SRI) comes on and flashes for about 6 seconds after the ignition key is turned to the "ON" position or after the engine is started, after which it will go out.


This light also comes on when the SRS is not working properly. If the SRI does not come on, or continuously remains on after flashing for about 6 seconds when you turned the ignition key to the "ON" position or started the engine, or if it comes on while driving, have the SRS inspected by an authorized Hyundai Dealer.


When the key is turned to the "ON" position, the Anti-Lock Brake System will come on and then go off after three seconds. If the ABS SRI remains on, comes on while driving, or does not come on when the key is turned to the "ON" position, this indicates that there may be a problem with the ABS. If this occurs, have your vehicle checked by your Hyundai dealer as soon as possible. The normal braking system will still be operational, but without the assistance of the anti-lock brake system.


WARNING:


If the both ABS SRI and Parking Brake/ Brake fluid level warning lights remain "ON" or come on while driving, there may be a problem with E.B.D (Electronic brake force distribution). If this occurs, avoid sudden stops and have your vehicle checked by your Hyundai dealer as soon as possible.


Turn Signal Indicator Lights


The blinking green arrows on the instrument panel show the direction indicated by the turn signals. If the arrow comes on but does not blink, blinks more rapidly than normal, or does not illuminate at all, a malfunction in the turn signal system is indicated. Your dealer should be consulted for repairs.


B260F01A-AAT


High Beam Indicator Light


The high beam indicator light comes on when- ever the headlights are switched to high beam of flash position.


1 FEATURES OF YOUR HYUNDAI


46


B260G01A-AAT


B260H03A-AAT


Low Oil Pressure Warning Light


Parking Brake/Low Brake Fluid Level Level Warning Light


CAUTION:


If the oil pressure warning light stays on while the engine is running, serious engine damage may result. The oil pressure warn- ing light comes on whenever there is insuf- ficient oil pressure. In normal operation, it should come on when the ignition switch is turned on, then go out when the engine is started. If the oil pressure warning light stays on while the engine is running, there may be a serious malfunction. If this happens, stop the car as soon as it is safe to do so, turn off the engine and check the oil level. If the oil level is low, fill the engine oil to the proper level and start the engine again. If the light stays on with the engine running, turn the engine off imme- diately. In any instance where the oil light stays on when the engine is running, the engine should be checked by a Hyundai dealer before the car is driven again.


! WARNING:


If you suspect brake trouble, have your brakes checked by a Hyundai dealer as soon as possible. Driving your car with a problem in either the brake electrical sys- tem or brake hydraulic system is danger- ous, and could result in a serious injury or death.


Warning Light Operation


The parking brake/brake fluid level warning light should come on when the parking brake is applied and the ignition switch is turned to "ON" or "START". After the engine is started, the light should go out when the parking brake is re- leased. If the parking brake is not applied, the warning light should come on when the ignition switch is turned to "ON" or "START", then go out when the engine starts. If the light comes on at any other time, you should slow the vehicle and bring it to a complete stop in a safe location off the roadway.


The brake fluid level warning light indicates that the brake fluid level in the brake master cylinder is low and hydraulic brake fluid conforming to DOT 3 or DOT 4 specifications should be added. After adding fluid, if no other trouble is found, the car should be immediately and care- fully driven to a Hyundai dealer for inspection. If further trouble is experienced, the vehicle should not be driven at all but taken to a dealer by a professional towing service or some other safe method. Your Hyundai is equipped with dual-diagonal braking systems. This means you still have braking on two wheels even if one of the dual systems should fail. With only one of the dual systems working, more than normal pedal travel and greater pedal pressure are required to stop the car. Also, the car will not stop in as short a distance with only half of the brake system working. If the brakes fail while you are driving, shift to a lower gear for additional engine braking and stop the car as soon as it is safe to do so.


FEATURES OF YOUR HYUNDAI


47


B260J01A-AAT


B260K01E-GAT


B260M01A-AAT


Charging System Warning Light


The charging system warning light should come on when the ignition is turned on, then go out when the engine is running. If the light stays on while the engine is running, there is a malfunc- tion in the electrical charging system. If the light comes on while you are driving, stop, turn off the engine and check under the hood. First, make certain the generator drive belt is in place. If it is, check the tension of the belt. Do this as shown on page 6-20 by pushing down on the center of the belt. And then, have the system checked by your Hyundai dealer.


B260E02O-AAT


Seat belt reminder light and chime


The seat belt reminder light blinks until your seat belt is fastened when the ignition key is turned from the "OFF" position to "ON" or "START". And the warning chime will sound for 6 seconds.


Trunk Lid (4 door)/Tail Gate (5 door) Open Warning Light


This light remains on unless the trunk lid/tail gate is completely closed.


B260L01Y-AAT


Door Ajar Warning Light and Chime


The door ajar warning light warns you that a door is not completely closed and the chime warns you that driver's side front door is not completely closed.


NOTE: To remind you not to lock the key inside the car, the warning light comes on whenever the key is in the "LOCK" position and a door is open. The warning chime only sounds whenever the key is in the "LOCK" position and the driver's side front door is open. The chime sounds and the light remains on until the key is removed from the ignition.


Low Fuel Level Warning Light


The low fuel level warning light comes on when the fuel tank is approaching empty. When it comes on, you should add fuel as soon as possible. Driving with the fuel level warning light on or with the fuel level below "E" can cause the engine to misfire and damage the catalytic converter.


B260Q01E-GAT


Cruise Indicator Light (If Installed)


The cruise indicator light in the instrument clus- ter is illuminated when the cruise control main switch on the end of the barrel is pushed. The indicator light does not illuminate when the cruise control main switch is pushed a second time. Information on the use of cruise control may be found on page 1-77.


1 FEATURES OF YOUR HYUNDAI


48


B260R01E-GAT


Set Indicator Light (If installed)


The set indicator light in the instrument cluster is illuminated when the cruise control switch is pushed downward to "SET (COAST)". The set indicator light does not illuminate when the control switch is "CANCEL" position.


B260A01B-GAT


Front Fog Indicator Light (If Installed)


Front fog indicator light comes on whenever the fog light switch is on.


B260N01A-AAT


Malfunction Indicator Light


This light illuminates when there is a malfunction of an exhaust gas related component, and the system is not functioning properly so that the exhaust gas regulation values are not satisfied. This light will also illuminate when the ignition key is turned to the "ON" position, and will go out in a few seconds. If it illuminates while driving, or does not illuminate when the ignition key is turned to the "ON" position, take your car to your nearest authorized Hyundai dealer and have the system checked.


B265C01O-AAT


Traction Control Indicator Lights (If installed)


The traction control indicators change opera- tion according to the ignition switch position and whether the system is in operation or not. They will illuminate when the ignition key is turned to the "ON" position, but should go out after three seconds. If the TCS or TCS-OFF indicator stays on, take your car to your autho- rized Hyundai dealer and have the system checked. See section 2 for more information about the TCS.


B270A01A-AAT BRAKE PAD WEAR WARNING SOUND


The front disc brake pads have wear indicators that should make a high-pitched squealing or scraping noise when new pads are needed. The sound may come and go or be heard all the time when the vehicle is moving. It may also be heard when the brake pedal is pushed down firmly. Expensive rotor damage will result if the worn pads are not replaced. See your Hyundai dealer immediately.


INSTRUMENT CLUSTER


B280A01A-AAT FUEL GAUGE Without Trip Computer


With Trip Computer


HXDFL291


HXDFL284
The needle on the gauge indicates the approxi- mate fuel level in the fuel tank. The fuel capacity is given in Section 9.


B290A02A-AAT ENGINE COOLANT TEMPERATURE GAUGE Without Trip Computer


WARNING:


Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could erupt and cause severe burns. Wait until the engine is cool before removing the radiator cap.


FEATURES OF YOUR HYUNDAI


49


B300A01S-AAT SPEEDOMETER Without Trip Computer


With Trip Computer


HXDFL290


The needle on the engine coolant temperature gauge should stay in the normal range. If it moves across the dial to "H" (Hot), pull over and stop as soon as possible and turn off the engine. Then open the hood and, after the engine has cooled, check the coolant level and the water pump drive belt. If you suspect cooling system trouble, have your cooling system checked by a Hyundai dealer as soon as possible.


With Trip Computer


HXDFL030-A


HXDFL283


HXDFL029-A Your Hyundai's speedometer is calibrated in miles per hour (on the outer scale) and kilome- ters per hour (on the inner scale).


1 FEATURES OF YOUR HYUNDAI


50


B330A01L-AAT TACHOMETER Without Trip Computer


The tachometer registers the speed of your engine in revolutions per minute (rpm).


B310B04E-AAT ODOMETER/TRIP ODOMETER


Without Trip Computer


CAUTION:


The engine should not be raced to such a speed that the needle enters the red zone on the tachometer face. This can cause severe engine damage and may void your warranty.


With Trip Computer


HXDFL330


HXDFL331


HXDFL231-A


Odometer Records the total distance the vehicle has been driven.


NOTE: Federal law forbids alteration of the odom- eter of any vehicle with the intent to change the number of the odometer. The alteration of the odometer may void your warranty coverage.


Function of digital odometer/trip odom- eter


Pushing in the reset switch under the right side of the speedometer when the ignition switch is turned "ON" will display the following sequence:


Reset switch


HXDFL078-A


1. Odometer The odometer records the total driving distance in miles or kilometers.


HXDFL077-1


2,3 Trip odometer Records the distance of 2 trips in miles or kilometers.


TRIP A: first distance you have traveled from your origination point to a first destina- tion.


TRIP B: Second distance from the first destina-


tion to the final destination.


To shift from TRIP A to TRIP B, press the reset switch. When pressed for 1 second, it will reset to 0.


FEATURES OF YOUR HYUNDAI


51


B310A01S-AAT ODOMETER With Trip Computer


Odometer


HXDFL230


The odometer records the total driving distance in miles or kilometers, and is useful for keeping a record for maintenance intervals.


NOTE: Federal law forbids alteration of the odom- eter of any vehicle with the intent to change the number of the odometer. The alteration of the odometer may void your warranty coverage.


o This mode provides the total distance trav- elled since the last tripmeter reset. Total distance is also reset to zero if the battery is disconnected.


o Pressing the trip computer switch for more than 1 second, when the tripmeter is being displayed, clears the tripmeter to zero.


o The meter's working range is from 0 to 999.9


miles.


1 FEATURES OF YOUR HYUNDAI


52


B400B03E-AAT TRIP COMPUTER (If Installed)


TRIPMETER


AVERAGE FUEL CONSUMPTION


DISTANCE TO EMPTY


1. Tripmeter


Tripmeter


Odometer


HXDFL230A-A


HXDFL371-1


The trip computer is a microcomputer-con- trolled driver information gauge that displays information related to driving, such as estimated tripmeter, average fuel consumption and dis- tance to empty on the LCD.


Trip Computer Switch


o The trip computer switch is used to zero the


multi-functional display mode.


o Pushing in the trip computer switch behind the left side of the handle changes the display as follows;


2. Average Fuel Consumption


3. Distance to Empty


Average fuel consumption


Distance to empty symbol


Distance to empty


Distance to empty FLASHING


Distance to empty symbol


FEATURES OF YOUR HYUNDAI


53


Odometer


HXDFL230-A


o This mode calculates the average fuel con- sumption from the total fuel used and the distance since the last average consump- tion reset.


o The total fuel used is calculated from the fuel


consumption input.


o For an accurate calculation, drive more than


0.5 mile.


o The meter's working range is from 0.0 to 99.9


miles/gallon(MPG).


Odometer


HXDFL1026-A


NOTE: o The distance to empty can differ from the actual tripmeter according to driving conditions.


o The distance to empty can vary accord- ing to the driving conditions, driving pattern or vehicle speed.


Odometer


HXDFL230B-A o This mode provides the estimated distance to empty from the current fuel level in the fuel tank and distance to empty symbol.


o When refueling with more than 2 gallons, the trip computer will recognize refueling has occurred.


o For an accurate distance to empty, drive


more than 0.5 mile.


o When the distance to empty is less than 30 miles, the symbol will always come on and the distance to empty digits will indicate "----" with flash until the fuel be added.


1 FEATURES OF YOUR HYUNDAI


54


MULTI-FUNCTION LIGHT SWITCH


B340A01A-AAT COMBINATION TURN SIGNAL, HEADLIGHT AND HIGH-BEAM SWITCH Turn Signal Operation


Pulling down on the lever causes the turn signals on the left side of the car to blink. Pushing upwards on the lever causes the turn signals on the right side of the car to blink. As the turn is completed, the lever will automatically return to the center position and turn off the turn signals at the same time. If either turn signal indicator light blinks more rapidly than usual, goes on but does not blink, or does not go on at all, there is a malfunction in the system. Check for a burned- out fuse or bulb or see your Hyundai dealer.


B340B01A-AAT Lane Change Signal


B340C03E-AAT Headlight Switch


HXDFL352


HXDFL360


To indicate a lane change, move the lever up or down to a point where it begins flashing. The lever will automatically return to the center position when released.


To operate the headlights, turn the barrel on the end of the multi-function switch. The first posi- tion turns on the parking lights, sidelights, tail lights and instrument panel lights. The second position turns on the headlights.


NOTE: The ignition must be in the "ON" position to turn on the headlights.


Parking light auto cut


If you do not turn the parking lights "OFF" after driving, the parking lights will automatically shut "OFF" when the driver's door is opened. To turn them "ON" again you must simply turn the ignition key to the "ON" position.


B340D01A-AAT High-beam Switch


To turn on the headlight high beams, push the lever forward (away from you). The high beam indicator light will come on at the same time. For low beams, pull the lever back toward you.


B340E01A-AAT Headlight Flasher


B340G01L-GAT Auto Light (If Installed)


FEATURES OF YOUR HYUNDAI


55


HXDFL351


To flash the headlights, pull the switch lever toward you, then release it. The headlights can be flashed even though the headlight switch is in the "OFF" position.


HXDFL361
To operate the automatic light feature, turn the barrel on the end of the multi-function switch. If you set the multi-function switch to "AUTO", the tail lights and headlights will be turned automati- cally on or off according to external illumination.


1 FEATURES OF YOUR HYUNDAI


56


B360B01Y-GAT FRONT FOG LIGHT SWITCH (If Installed)


WINDSHIELD WIPER AND WASHER SWITCH


B350A01A-AAT


B350C01S-AAT Adjustable Intermittent Wiper Operation


HXDFL359


The windshield wiper switch has three posi- tions:


HXDFL353-A


To turn on the front fog lights, place the switch in the "ON" position. They will come on when the headlight switch is in the second position.


Intermittent wiper operation


1. 2. Low-speed operation 3. High-speed operation


NOTE: To prevent damage to the wiper system, do not attempt to wipe away heavy accumula- tions of snow or ice. Accumulated snow and ice should be removed manually. If there is only a light layer of snow or ice, operate the heater in the defrost mode to melt the snow or ice before using the wiper.


HXDFL354-A


To use the intermittent wiper feature, place the wiper switch in the "INT" position. With the switch in this position, the interval between wipes can be varied from 2 to 10 seconds by turning the interval adjuster barrel.


B350B01A-AAT Windshield Washer Operation


Mist Wiper Operation


FEATURES OF YOUR HYUNDAI


57


B390A01E-AAT REAR WINDOW WIPER AND WASHER (If Installed)


HXDFL355-A To use the windshield washer, pull the wiper/ washer lever toward the steering wheel. When the washer lever is operated, the wipers auto- matically make two passes across the wind- shield. The washer continues to operate until the lever is released.


NOTE: o Do not operate the washer more than 15
seconds at a time or when the fluid reser- voir is empty.


o In icy or freezing weather, be sure the wiper blades are not frozen to the glass prior to operating the wipers.


o In areas where water freezes in winter,


use windshield washer antifreeze.


If a single wipe is desired in mist, push the windshield wiper and washer control lever up- wards.


1.


HXDFL356-A


HXDFL357-A


: The rear window wiper starts to oper- ate three times after the washer fluid sprays onto the rear window.


2.OFF 3.INT : The interval between wipes operates


every 5 seconds intermittently.


4.ON : The rear window wiper starts to oper-


5.


ate continuously.


: The washer fluid will be sprayed onto the rear window and the wiper oper- ates while the rear window wiper bar- rel is placed in this position.


1 FEATURES OF YOUR HYUNDAI


58


Do not operate the washer continuously for more than 15 seconds or when the fluid reser- voir is empty; this could damage the system. Do not operate the wiper when the window is dry; this can result in scratching as well as prema- ture wiper blade wear. For the reason stated above,do not operate the washer when the washer fluid reservoir is empty.


REAR WINDOW DEFROSTER SWITCH


B380A01A-AAT


CAUTION:


Do not clean the inner side of the rear window glass with an abrasive type of glass cleaner or use a scraper to remove foreign deposits from the inner surface of the glass as this may cause damage to the defroster elements.


NOTE: The ignition must be in the "ON" position for the rear window defroster to operate.


B380B01E-A The rear window defroster and heated outside rear wiew mirrors are turned on by pushing in the switch. To turn the defroster off, push the switch a second time. The rear window de- froster automatically turns itself off after about 15 minutes. To restart the defroster cycle, push in the switch again after it has turned itself off.


HAZARD WARNING SYSTEM


DIGITAL CLOCK


FEATURES OF YOUR HYUNDAI


INSTRUMENT PANEL LIGHT CONTROL (RHEOSTAT)


59


B370A01A-AAT


B400A01A-AAT


B410A01A-AAT


HXDFL371


HXDFL400


B410A01E-A


The hazard warning system should be used whenever you find it necessary to stop the car in a hazardous location. When you must make such an emergency stop, always pull off the road as far as possible. The hazard warning lights are turned on by pushing in the hazard switch. This causes all turn signal lights to blink. The hazard warning lights will operate even though the key is not in the ignition. To turn the hazard warning lights off, push the switch a second time.


There are three control buttons for the digital clock. Their functions are:


HOUR - Push "H" to advance the hour indi- cated. MIN - Push "M" to advance the minute indicated. RESET - Push "R" to reset minutes to ":00" to facilitate resetting the clock to the correct time. When this is done:


Pressing "R" between 10 : 30 and 11 : 29
changes the readout to 11 : 00. Pressing "R" between 11 : 30 and 12 : 29
changes the readout to 12 : 00.


The instrument panel lights can be made brighter or dimmer by turning the instrument panel light control knob.


1 FEATURES OF YOUR HYUNDAI


60


CIGARETTE LIGHTER


B420A01A-AAT


POWER OUTLET


ASHTRAY


B500D07O-GAT (If Installed)


B430A01E-AAT FRONT ASHTRAY


HXDFL420
For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position. To use the cigarette lighter, push it all the way into its socket. When the element has heated, the lighter will pop out to the "ready" position. Do not hold the cigarette lighter pressed in. This can damage the heating element and create a fire hazard. If it is necessary to replace the cigarette lighter, use only a genuine Hyundai replacement or its approved equivalent.


HXDFL421


HXDFL440


These supply 12V electric power to operate electric accessories or equipment only when the key is in the "ON" or "ACC" position.


CAUTION:


Do not use the power outlet to connect electric accessories or equipment other than those designed to operate on 12 volts.


The front ashtray may be opened by pushing and releasing the ashtray lid. To remove the ashtray to empty or clean it, lift the ashtray upward and pull it out. The ashtray light will only illuminate when the external lights are on (If installed).


PARKING BRAKE


DRINK HOLDER


FEATURES OF YOUR HYUNDAI


61


B440A01E-AAT REAR ASHTRAY


B530A01A-AAT


B450A01E-AAT FRONT DRINK HOLDER


B430A01E


The rear ashtray may be opened by pulling the lid out by its top edge. To remove the ashtray to empty or clean it, press down on the spring- loaded tab inside the ashtray and lift the ashtray upward and pull it all the way out.


B530A01E Always engage the parking brake before leav- ing the car. This also turns on the parking brake indicator light when the key is in the "ON" or "START" position. Before driving away, be sure that the parking brake is fully released and the indicator light is off.


o To engage the parking brake, pull the lever


up as far as possible.


o To release the parking brake, pull up the lever and press the thumb button. Then, while holding the button in, lower the brake lever.


HXDOM120
The drink holder is located in the right side of parking brake for holding cups or cans.


WARNING:


Do not place objects other than cups or cans in the drink holder. Such objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the pas- sengers in the vehicle.


1 FEATURES OF YOUR HYUNDAI


62


B450B02E-AAT REAR DRINK HOLDER (If Installed)


4DOOR


SEATBACK POCKET


The rear drink holder is located in the rear seat center (center of the rear seat arm rest- 5 door) for holding cups or cans. The drink holder can be used by pushing it in first and then releasing it.


B540B01E-GAT (If installed)


CAUTION:


Place the drink holder in its original posi- tion while not in use.


5DOOR


HXDOM302


HXDFL536-A


The seatback pockets are located on the back- side of the front seats for holding papers and so on.


HXDFL1033


SUNROOF


B470A01S-AAT SUNSHADE


B460B02E-AAT OPERATING THE SUNROOF SYSTEM Opening or Closing the Sunroof


FEATURES OF YOUR HYUNDAI


63


WARNING:


o Do not close a sunroof if anyone's hands, arms or body are between the sliding glass and the sunroof sash, as this could result in an injury.


o Do not place your head or arms out of the


sunroof opening at any time.


B470A01E


The sunshade can be opened and closed by sliding it forward or rearward when the sunroof is closed. The sunshade will open automatically when the sunroof is opened, but it must be closed manually.


B460A01S-AAT SUNROOF (If Installed)


The sunroof can be operated with the ignition key in the "ON" position.


B460B02E-A The sunroof can be electrically opened or closed with the ignition key in the "ON" position. The sunroof is moved to its fully open position by pushing the "Open" switch, and to stop at the desired position, push in any switches (Open, Close, Up, Down). To close, press and hold the "CLOSE" button. Release the button when the sunroof reaches the desired position.


CAUTION:


o Do not open the sunroof in severely cold temperature or when it is covered with ice or snow.


o Periodically remove any dirt that may


have accumulated on the guide rails.


1 FEATURES OF YOUR HYUNDAI


64


B460C01S-AAT Tilting the Sunroof


B460D02E-AAT Manual Operation of Sunroof


B460C02E-A


B460D02E-A


The sunroof can be tilted by pushing the button with the sunroof closed. Release the button when the sunroof reaches the desired position.


NOTE: After washing the car or after there is rain, be sure to wipe off any water that is on the sunroof before operating it.


If the sunroof does not electrically operate:


1. Remove the rectangular plastic interior light


lens in the front overhead console.


2. Remove the front overhead console with a


phillips screwdriver.


B460E02E-A


3.


B460F02E-A Insert the hexagonal head wrench provided with the vehicle into the socket. This wrench can be found in the vehicle's trunk or glove box.


4. Turn the wrench clockwise to open or coun-


terclockwise to close.


FEATURES OF YOUR HYUNDAI


65


INTERIOR LIGHT


B480A01E-AAT FRONT INTERIOR LIGHT Map Light


With Sunroof


Without Sunroof


B490A01E-AAT Interior light


B480A02E-A


The two map light buttons are located on both sides of the front overhead console. Push in the map light button to turn the light on or off. This light produces a spot beam for convenient use as a map light at night or as a personal light for the driver and the passenger.


B490B01E


The interior courtesy light has switch of three positions. The three positions are:


o DR In the "DR" position, the interior courtesy light comes on when any door is opened regardless of the ignition key position. The light goes out when the door is closed.


o ON In the "ON" position, the light stays on at all times.


o OFF In the "OFF" position, the light stays off at all times even though a door is open.


1 FEATURES OF YOUR HYUNDAI


66


SPECTACLE CASE


B491A02F-GAT (If Installed)


GLOVE BOX


MULTI BOX


B500A01S-AAT


B500B02E-GAT


HXDOM241


The spectacle case is located on the front overhead console. Push the end of cover to open the spectacle case.


WARNING:


Do not open the spectacle case while the vehicle is moving. The rear view mirror of the vehicle can be blocked.


HXD301
The multi box may be opened by pulling it out by its grip. It is used for storing small articles. If the muti box is removed, the fuse box for the lights and other electrical accessories will be exposed.


B500A01E


WARNING:


To avoid the possibility of injury in case of an accident or a sudden stop, the glove box door should be kept closed when the car is in motion.


o To open the glove box, pull on the glove box


release lever.


o The glove box door can be locked (and


unlocked) with the key (If installed).


MIRROR


B510A01S-AAT OUTSIDE REARVIEW MIRROR Manual Type


B510A01E The outside rearview mirror on the driver's side is equipped with a remote control for your convenience. It is operated by the control lever in the bottom front corner of the window. Before driving away, always check that your mirrors are positioned so you can see behind you, both to the left and right sides, as well as directly behind your vehicle. When using the mirror, always exercise caution when attempt- ing to judge the distance of vehicles behind or along side of you.


FEATURES OF YOUR HYUNDAI


67


NOTE: If the mirror control is jammed with ice, do not attempt to break it free using the control handle or by manipulating the face of the mirror. Use an approved spray de-icer (not radiator antifreeze) to release the frozen mechanism or move the vehicle to warm place and allow the ice to melt.


B510B01Y-AAT Electric Type (If Installed)


The outside rearview mirrors can be adjusted to your preferred rear vision, both directly be- hind the vehicle, and to the rear of the left and right sides. The remote control outside rearview mirror switch controls the adjustments for both right and left outside mirrors.


To adjust the position of either mirror: 1. Move the selecting switch to the right or left to activate the adjustable mechanism for the corresponding door mirror.


2. Now, adjust mirror angle by depressing the appropriate perimeter switch as illustrated.


B510C01E


B510D01E


1 FEATURES OF YOUR HYUNDAI


68


CAUTION:


o Do not operate the switch continuously


for an unnecessary length of time.


o Scraping ice from the mirror face could cause permanent damage. To remove any ice, use a sponge, soft cloth or approved de-icer.


WARNING:


Be careful when judging the size or dis- tance of any object seen in the passenger side rear view mirror. It is a convex mirror with a curved surface. Any objects seen in this mirror are closer than they appear.


B510D01Y-AAT OUTSIDE REARVIEW MIRROR HEATER (If installed)


B510C01A-AAT FOLDING THE OUTSIDE REARVIEW MIRRORS


Manual


Automatic


B380A01GK


B510E01E


The outside rearview mirror heater is actuated in connection with the rear window defroster. To heat the outside rearview mirror glass, push in the switch for the rear window defroster. The rearview mirror glass will be heated for defrost- ing or defogging and will give you improved rear vision in inclement weather conditions. Push the switch again to turn the heater off. The outside rearview mirror heater automatically turns itself off after 15 minutes.


To fold the outside rearview mirrors, push them towards the rear. The outside rearview mirrors can be folded rearward for parking in narrow areas.


WARNING:


Do not adjust or fold the outside rearview mirrors while the vehicle is moving. This could result in loss of control, and an acci- dent which could cause death, serious in- jury or property damage.


B520A01A-AAT DAY/NIGHT INSIDE REARVIEW MIRROR Manual type


B520B01O-GAT Electric type (If installed)


B580A01L-GAT SUN VISOR


FEATURES OF YOUR HYUNDAI


69


HXDFL2112


Your Hyundai is equipped with a day/night inside rearview mirror. The "night" position is selected by flipping the tab at the bottom of the mirror toward you. In the "night" position, the glare of headlights of cars behind you is reduced.


HXDFL2113


The electric type day/night inside rearview mir- ror controls automatically the glare of headlights of the car behind you. Adjust the rearview mirror to the desired position.


Vanity mirror


B580A01E


Your Hyundai is equipped with sun visors to give the driver and front passenger either frontal or sideward shade. To reduce glare or to shut out direct rays of the sun, turn the sun visor down. A vanity mirror is provided on the back of the sun visor for the driver and front passenger. NOTE: The Supplemental Restraint System (SRS) label containing useful information can be found on the back of each sun visor.


1 FEATURES OF YOUR HYUNDAI


70


WARNING:


Do not place the sun visor in such a manner that it obscures visibility of the roadway, traffic or other objects.


HIGH-MOUNTED REAR STOP LIGHT


B550A01S-GAT (If Installed)


B620A01S-AAT FRONT DOOR EDGE WARNING LIGHT (If Installed)


B550A02E In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rear stoplight in the center of the rear window or inserted in the rear spoiler also lights when the brakes are applied.


B620A01E A red light turns on when the front door is opened. The purpose of this light is to assist when you get in or out and also to warn passing vehicles.


FEATURES OF YOUR HYUNDAI


71


B990A03Y-AAT FLOOR MAT ANCHOR


HXGS263


To use a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor in your vehicle. This keeps the floor mat from sliding forward.


HOOD RELEASE


B570A02E-AAT


2. Pull the secondary catch lever up and lift the


hood.


3. Hold the hood open with the support rod.


Before closing the hood, return the support rod to its clip to prevent it from rattling. Lower the hood until it is about 1 ft. (30 cm) above the closed position and let it drop. Make sure that it locks into place.


CAUTION:


Make sure that the support rod has been released prior to closing the hood.


HXD570
1. Pull the release knob to unlatch the hood.


WARNING:


o Always double check to be sure that the hood is firmly latched before driving away. If it is not latched, the hood could fly open while the vehicle is being driven, causing a total loss of visibility, which might result in an accident.


o The support rod must be inserted com- pletely into the hole provided in the hood whenever you inspect the engine compartment. This will prevent the hood from falling and possibly injuring you. o Do not move the vehicle with the hood in the raised position, as vision is ob- structed and the hood could fall or be damaged.


HXDFL570-A


1 FEATURES OF YOUR HYUNDAI


72


WARNING:


o make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and interferes with the movement of the pedals during driving, it may cause an accident.


o Don't put an additional floor mat on the top of the anchored mat, otherwise the additional mat may slide forward and interfere with the movement of the ped- als.


REMOTE FUEL-FILLER LID RELEAS


B560A02S-AAT


4 DOOR


5 DOOR


HXDFL561
The fuel-filler lid may be opened from inside the vehicle by pulling up on the fuel-filler lid opener located on the front floor area on the left side of the car.


NOTE: If the fuel-filler lid will not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved deicer fluid (do not use radiator anti-freeze) or move the ve- hicle to a warm place and allow the ice to melt.


B560B01E


WARNING:


o The fuel cap must be tightened at least 3 clicks, otherwise light will illuminate. o Gasoline vapors are dangerous. Before refueling, always stop the engine and never allow sparks or open flames near the filler area. If you need to replace the filler cap, use a genuine Hyundai re- placement part.


o If you open the fuel filler cap during high ambient temperatures, a slight "pres- sure sound" may be heard. This is nor- mal and not a cause for concern. Whenever you open the fuel filler cap, turn it slowly.


TRUNK LID / TAIL GATE


B540A01E-GAT TRUNK LID (4 DOOR) Remote Trunk Lid Release


FEATURES OF YOUR HYUNDAI


73


WARNING:


The trunk lid should always be kept com- pletely closed while the vehicle is in motion. If it is left open or ajar, poisonous exhaust gases may enter the car resulting in serious illness or death to the occupants. See addi- tional warnings concerning exhaust gases on page 2-2.


WARNING:


o Make sure the fuel filler cap is replaced and securely seated after fueling. Failure to replace or fully seat the fuel filler cap will result in fuel vapors escaping into the atmosphere and the MIL indicator illuminating.


o Do not "TOP-OFF" after the first nozzle


shut off when refueling.


B540A02E To open the trunk lid without using the key, pull up the lid release lever. To close, lower the trunk lid, then press down on it until it locks. To be sure the trunk lid is securely fastened, always try to pull it up again.


1 FEATURES OF YOUR HYUNDAI


74


B540C01S-AAT To Unlock Using the Key


B540B02E-AAT Trunk Lid Emergency Latch Release


WARNING:


Parents should teach children about the emergency trunk release lever in their ve- hicle and how to open the trunk lid if they are accidentally locked in the trunk.


To open the trunk lid, insert the key and turn it clockwise to unlock. The trunk lid compartment light illuminates when the trunk lid is opened.


B540C02E


Pull to open the trunk


B540E02E-A Your vehicle is equipped with a glow-in-the dark emergency trunk release lever located inside the trunk. It will glow after the trunk is closed. When pulled, this lever will release the trunk latch mechanism and open the trunk.


NOTE: o If a person is locked in the trunk, pull the emergency trunk release lever on the driver's side of the inside panel of the trunk to open the trunk lid.


o HYUNDAI recommends that cars be kept locked and keys be kept out of the reach of children, and that parents teach their children about the dangers of playing in trunks.


B540F02E-GAT TAIL GATE (5 DOOR) Operation From Outside The Vehicle


B540F02E To open the tail gate, insert the key and turn it clockwise to unlock. Then, pull the outside handle toward you.


Storage Box


LUGGAGE NET


B540D01E-GAT (If Installed)


FEATURES OF YOUR HYUNDAI


75


Loading...
x