).
63
2011 RidgelineOnmodelswithnavigationsystem
You will also see a ‘‘CHECK
AIRBAG SYSTEM’’ message on the
multi-information display (see page
90
).
10/04/19 15:47:00 31SJC650_069
Instrument Panel Indicators
Supplemental Restraint System Indicator
This indicator comes on for several
seconds when you turn the ignition
switch to the ON (II) position. If it
comes on at any other time, it
indicates a potential problem with
your front airbags. This indicator will
also alert you to a potential problem
with your side airbags, passenger’s
side airbag automatic cutoff system,
side curtain airbags, rollover sensor,
automatic seat belt tensioners,
driver’s seat position sensor, or the
front passenger’s weight sensors.
For more information, see page
30
64
U.S.
Canada
Side Airbag Off Indicator
This indicator comes on for several
seconds when you turn the ignition
switch to the ON (II) position. If it
comes on at any other time, it
indicates that the passenger’s side
airbag has automatically shut off.
For more information, see page
31
Onmodelswithnavigationsystem
You will also see a ‘‘PASSENGER
SIDE AIRBAG OFF’’ message on the
multi-information display (see page
90
).
2011 Ridgeline10/04/19 15:47:07 31SJC650_070
Instrument Panel Indicators
U.S.
Canada
Parking Brake and Brake System Indicator
This indicator has two functions:
1.
It comes on when you turn the ignition switch to the ON (II) position. It is a reminder to check the parking brake. A beeper sounds if you drive with the parking brake not fully released. Driving with the parking brake not fully released can damage the brakes and tires.
Onmodelswithnavigationsystem
You will also see a ‘‘RELEASE
PARKING BRAKE’’ message on the
multi-information display (see page
90
).
2.
If it stays on after you have fully released the parking brake while the engine is running, or if it comes on while driving, there could be a problem with the brake system. For more information, see page
376
Onmodelswithnavigationsystem
You will also see a ‘‘BRAKE FLUID
LOW’’ or ‘‘CHECK BRAKE
SYSTEM’’ message on the multi-
information display (see page
90
) .
65
2011 Ridgeline10/04/19 15:47:15 31SJC650_071
Instrument Panel Indicators
Anti-lock Brake System (ABS) Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position. If it comes on at any other time, there is a problem with the ABS. If this happens, have your vehicle checked at a dealer. With the indicator on, your vehicle still has normal braking ability but no anti- lock brakes. For more information, see page
289
Onmodelswithnavigationsystem
You will also see a ‘‘CHECK ABS
SYSTEM’’ message on the multi-
information display (see page
91
).
66
Immobilizer System Indicator
This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. It will go off if you have inserted a properly coded ignition key. If it is not a properly coded key, the indicator will blink and the engine will not start (see page
101
).
This indicator also blinks several times when you turn the ignition switch from the ON (II) position to the ACCESSORY (I) or LOCK (0) position.
Turn Signal and Hazard Warning Indicators
The left or right turn signal indicator blinks when you signal a lane change or turn. If an indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see pages ). and Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.
338
340
When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.
2011 Ridgeline10/04/19 15:47:25 31SJC650_072
Daytime Running Lights Indicator
If this indicator comes on when the ignition switch is turned to the ON (II) position and the parking brake is released, it means there is a problem with a circuit. Have your vehicle checked by your dealer.
Onmodelswithnavigationsystem If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem with the daytime running light circuit. Take your vehicle to a dealer to have it checked.
Instrument Panel Indicators
High Beam Indicator
Washer Level Indicator
This indicator comes on with the high beam headlights. For more information, see page
95
Cruise Main Indicator
This indicator comes on when you turn on the cruise control system by pressing the CRUISE button (see page
210
).
This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator (see page
330
).
Onmodelswithnavigationsystem You will see a ‘‘WASHER FLUID LOW’’ message on the multi- information display (see page
91
).
Cruise Control Indicator
This indicator comes on when you
set the cruise control. See page
210
cruise control.
for information on operating the
67
2011 Ridgeline10/04/19 15:47:32 31SJC650_073
Instrument Panel Indicators
Low Fuel Indicator
LOW FUEL INDICATOR
This indicator comes on as a reminder that you must refuel soon.
When the indicator comes on, there are about 3.3 U.S. gal (12.5 ) of fuel remaining in the tank.
When the needle reaches E, there is a very small amount of fuel in the tank.
68
Onmodelswithnavigationsystem You will also see a ‘‘FUEL LOW’’ message on the multi-information display.
Security System Indicator OnRTS,RTLmodels,andCanadian EX-Lmodels
SECURITY SYSTEM INDICATOR
This indicator comes on when the
security system is set. See page
208
for more information on the
security system.
2011 Ridgeline10/04/19 15:47:38 31SJC650_074
Lights On Indicator
This indicator reminds you that the exterior lights are on. It comes on when you turn the headlight control dial to either the
or
position.
If you turn the ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the headlight control dial, this indicator remains on. A reminder chime will also sound when you open the driver’s door.
A/T Temperature Indicator
This indicator monitors the temperature of the automatic transmission fluid. It should come on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on while driving, it means the transmission fluid temperature is too high. Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.
Onmodelswithnavigationsystem You will also see an ‘‘A/T TEMP HIGH’’ message on the multi- information display (see page
91
).
Instrument Panel Indicators
Continuing to drive with the A/T temperature indicator on may cause serious damage to the transmission.
69
2011 Ridgeline11/07/12 15:04:35 31SJC650_075
Instrument Panel Indicators
VTM-4 Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, there is a problem in the 4WD system. Take the vehicle to your dealer to have it checked.
If the indicator blinks while driving, the VTM-4 fluid temperature is too high. Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.
Continuing to drive with the VTM-4
indicator blinking may cause serious
damage to the system.
Vehicle Stability Assist (VSA) System Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
This indicator has two functions:
Onmodelswithnavigationsystem
You will also see a ‘‘CHECK VSA
SYSTEM’’ message on the multi-
information display (see page
91
).
1.
2.
It flashes when VSA is active (see page
291
).
If it comes on and stays on at any
other time, there is a problem with
the VSA system. Take your
vehicle to a dealer to have it
checked. Without VSA, your
vehicle still has normal driving
ability, but will not have VSA
traction and stability enhancement.
For more information, see page
290
70
2011 Ridgeline
11/07/12 15:04:41 31SJC650_076
VSA OFF Indicator
It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. For more information, see page
291
Instrument Panel Indicators
Maintenance Minder Indicator
This indicator comes on for a few
seconds when you turn the ignition
switch to the ON (II) position. It
reminds you that it is time to take
your vehicle in for scheduled
maintenance. The maintenance main
items and sub items will be displayed
in the information display. See page
313
Maintenance Minder .
for more information on the
TM
This indicator goes off when your dealer resets it after completing the required maintenance service.
2011 Ridgeline
71
10/04/19 15:48:04 31SJC650_077
Instrument Panel Indicators
Low Tire Pressure Indicator
Onmodelswithoutnavigationsystem This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.
72
If this happens, pull to the side of the
road when it is safe, check which tire
has lost the pressure on the tire
pressure monitor, and determine the
cause. If it is because of a flat tire,
replace the flat tire with the compact
spare (see page
), and have the
flat tire repaired as soon as possible.
If two or more tires are underinflated,
call a professional towing service
(see page
278
for more information.
). Refer to page
383
361
Low Tire Pressure/ TPMS Indicator
Onmodelswithnavigationsystem This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. This indicator has two functions:
1.
If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.
You will also see a ‘‘CHECK TIRE PRESSURE’’ message on the multi-information display (see page
91
) .
Check the tire pressure monitor
on the multi-information display
and determine the cause (see page
282
).
2011 Ridgeline10/04/19 15:48:10 31SJC650_078
2.
If this happens, pull to the side of the
road when it is safe, check which tire
has lost pressure on the multi-
information display, and determine
the cause. If it is because of a flat tire,
have the flat tire repaired as soon as
possible. If two or more tires are
underinflated, call a professional
towing service. For more
information, see page
383
If this indicator begins to flash,
there is a problem with the tire
pressure monitoring system
(TPMS). You will also see a
‘‘CHECK TPMS SYSTEM’’
message on the multi-information
display. The indicator continues to
flash for a while (approximately 1
minute), then stays on. If this
happens, have your dealer check
the system as soon as possible.
For more information, see
page
284
Instrument Panel Indicators
Tire Pressure Monitoring System (TPMS) Indicator
Onmodelswithoutnavigationsystem This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the TPMS. With this indicator on, the low tire pressure indicator and the tire pressure monitor will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked.
73
2011 RidgelineIf you turn the ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the bed lights, this indicator will remain on, and then go off after 20 minutes. See page
for more information.
144
10/04/19 15:48:16 31SJC650_079
Instrument Panel Indicators
Message Indicator
Bed Lights On Indicator
This indicator reminds you that the bed lights are on. With the shift lever in the Park position, they come on when you push the light switch on the dashboard, swing open the tailgate, or open the In-Bed Trunk.
Onmodelswithnavigationsystem
This indicator comes on when there
is a system message on the multi-
information display. Press the INFO
button on the dashboard (see page
82
page
) to see the message (see
90
).
Most of the time, this indicator comes on along with other indicators in the instrument panel such as the seat belt reminder indicator, SRS indicator, VSA system indicator, etc.
74
2011 Ridgeline10/04/19 15:48:23 31SJC650_080
In-Bed Trunk Open Indicator
This indicator reminds you that the In-Bed Trunk is open. If you do not close it, the indicator stays on for about 3 minutes. See page for more information.
116
Door and Tailgate Open Indicator
This indicator comes on if any door or the tailgate is not closed tightly.
Instrument Panel Indicators
Back Window Open Indicator
This indicator reminds you that the
back window is not completely
closed when you turn the ignition
switch from the ON (II) position to
the ACCESSORY (I) or LOCK (0)
position. With the ignition switch in
the ACCESSORY (I) position, it goes
off after about 30 seconds. With the
ignition switch in the LOCK (0)
position, it goes off after about 3
minutes.
If you remove the ignition key, turn
off the lights, and open the driver’s
door without closing the back
window, you will hear five beeps and
see the indicator blink. If you do not
close the back window before the
beeper stops, the indicator stops
blinking but remains on. It will go off
after about 3 minutes. See page
129
for more information.
75
2011 Ridgeline11/07/12 15:04:51 31SJC650_081
Gauges
On models without navigation system
TACHOMETER
SPEEDOMETER
TEMPERATURE GAUGE
SELECT BUTTON TRIP/RESET BUTTON
INFORMATION DISPLAY
FUEL GAUGE
On models with navigation system
TACHOMETER
SPEEDOMETER
TEMPERATURE GAUGE
INFO (
▲
) BUTTON
SEL/RESET BUTTON
INFO (
▼
) BUTTON
MULTI-INFORMATION DISPLAY
FUEL GAUGE
U.S. model is shown.
76
Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise to about the middle of the gauge. In severe driving conditions, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. For instructions and precautions on checking the engine’s cooling system, see page
372
Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount.
Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.
2011 Ridgeline10/04/19 15:48:40 31SJC650_082
Information Display Onmodelswithoutnavigationsystem The information display shows the odometer, trip meter, engine oil life, outside temperature (if equipped), instant fuel economy, average fuel economy, range (estimated distance), and maintenance item code(s).
Gauges
SELECT BUTTON
Onmodelswithnavigationsystem
For information about the multi-
information display, see page
.82
TRIP/RESET BUTTON
With the ignition switch in the ON (II) position, the information display changes as shown on the next page each time you press the SELECT button or TRIP/RESET button.
When you turn the ignition switch to the ON (II) position, your last selection display.
CONTINUED
77
2011 Ridgeline10/04/19 15:48:47 31SJC650_083
Gauges
INFORMATION DISPLAY
OUTSIDE TEMPERATURE INDICATOR
ODOMETER
ODOMETER
SELECT button TRIP/RESET button
TRIP METER A AVERAGE FUEL ECONOMY A
TRIP METER B AVERAGE FUEL ECONOMY B
INSTANT FUEL ECONOMY
TRIP METER A RANGE
INSTANT FUEL ECONOMY
TRIP METER B RANGE
TRIP METER A
TRIP METER B
ENGINE OIL LIFE
U.S. model is shown.
78
2011 Ridgeline10/04/19 15:48:57 31SJC650_084
Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.
TripMeter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the TRIP/ RESET button repeatedly. Each trip meter works independently, so you can keep track of two different distances. To reset a trip meter, display it, and then press and hold the TRIP/RESET button until the number resets to ‘‘0.0’’.
Both trip meters will reset if the vehicle’s battery goes dead or is disconnected.
OutsideTemperatureIndicator ExceptRTmodels This shows the outside temperature in Fahrenheit (U.S. models), or in Celsius (Canadian models).
The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.
In certain weather conditions, temperature readings near freezing
Gauges
(32°F, 0°C) could mean that ice is forming on the road surface.
If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.
5°F in U.S. models (
±
The temperature must be
NOTE: stabilized before doing this procedure.
To adjust the outside temperature
indicator, press and hold the TRIP/
RESET button for 10 seconds. The
following sequence will appear for 1
second each: 0, 1, 2, 3, 4, 5,
4,
− − −
− − −
− − 1, 0 (U.S.) or 0, 1, 2, 3, 1, 0 (Canada).
2, 2,
3, 3,
5,
When the temperature reaches the desired value, release the TRIP/ RESET button. You should see the new outside temperature displayed.
CONTINUED
79
2011 Ridgeline10/04/19 15:49:07 31SJC650_085
Gauges
TirePressureMonitor
TIRE PRESSURE MONITOR
The appropriate tire indicator will come on along with the low tire pressure indicator if a tire is significantly underinflated or has Low suddenly lost pressure. See Tire Pressure Indicator do if this indicator comes on.
for what to
Onmodelswithnavigationsystem This indicator is displayed as the system message on the multi- information display (see page
282
).
80
Range(EstimatedDistance) This display shows the estimated distance you can travel on the fuel remaining in the tank.
This distance is estimated from the fuel economy you have achieved over the last few miles (kilometers), so it will vary with changes in speed, traffic condition, etc.
InstantFuelEconomy This display shows the instant fuel economy you are getting.
It shows the number of mpg (U.S.) or l/100 km (Canada).
AverageFuelEconomy When either of the trip meters (trip A or B) is displayed, your vehicle’s average fuel economy since you last reset that trip meter can be shown on the information display (mpg on U.S. models and l/100 km on Canadian models). This number is updated once per 10 seconds. To see the average fuel economy, press and release the TRIP/RESET button repeatedly.
The average fuel economy will be reset when you reset the trip meter, or if the vehicle’s battery goes dead or is disconnected.
2011 Ridgeline10/04/19 15:49:14 31SJC650_086
Gauges
TM
MaintenanceMinder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.
313
for
If the system still detects a leak in your vehicle’s evaporative emissions system, the malfunction indicator lamp (MIL) comes on. If the fuel fill cap was not already tightened, turn the engine off, and check or retighten the fuel fill cap until it clicks at least once. The MIL should go off after several days of normal driving once the cap is tightened or replaced. If the MIL does not go off, have your vehicle inspected by a dealer. For more information, see page
375
CheckFuelCapMessage Your vehicle’s onboard diagnostic system will detect a loose or missing fuel fill cap as an evaporative system leak. The first time a leak is detected a ‘‘CHECK FUEL CAP’’ message appears on the information display.
Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen it, then retighten it until it clicks at least once. The message should go off after several days of normal driving once you tighten or replace the fuel fill cap. To scroll to another display, press the SELECT button or TRIP/RESET button.
The ‘‘CHECK FUEL CAP’’ message will appear each time you restart the engine until the system turns the message off.
81
2011 Ridgeline10/04/19 15:49:20 31SJC650_087
Multi-Information Display
Onmodelswithnavigationsystem The multi-information display in the instrument panel displays various information and messages when the ignition switch is in the ON (II) position. Some of the messages help you operate your vehicle more comfortably. Others help to keep you aware of the periodic maintenance your vehicle needs for continued trouble-free driving.
When you open the driver’s door, a ‘‘Welcome’’ message is shown on the multi-information display.
82
INFO (
▲
) BUTTON
With the ignition switch in the ON (II) position, the multi-information display changes as shown on the next page each time you press the INFO ( / ) button or the SEL/ RESET button.
▲ ▼
SEL/RESET BUTTON
When you turn the ignition switch to the ON (II) position, your last selection is displayed.
INFO (
▼
) BUTTON
To change the display, press the INFO ( / ) button on the dashboard repeatedly until the main menu appears (see page
▲ ▼
83
).
In the multi-information display, the system message is also displayed (see page
90
).
2011 Ridgeline10/04/19 15:49:25 31SJC650_088
Multi-Information Display
(See page 84)
Trip Computer (See page 87)
Tire Pressure for each tire (See page 86)
Go to HandsFreeLink Menu (See page 86)
Go to Language Selection Menu (See page 92)
U.S. model is shown.
▲ ▼
INFO ( ) button SEL/RESET button
83
2011 Ridgeline10/04/19 15:49:32 31SJC650_089
Multi-Information Display
Odometer
Trip Meter
When you reset Trip A, AVERAGE FUEL A, AVERAGE SPEED A, and ELAPSED TIME A are reset at the same time. When you reset Trip B, AVERAGE FUEL B, AVERAGE SPEED B, and ELAPSED TIME B are reset.
ODOMETER U.S. model is shown.
The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.
U.S. model is shown.
TRIP METER
This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Each trip meter works independently, so you can keep track of two different distances.
To reset a trip meter, display it, and then press and hold the SEL/RESET button until the number resets to ‘‘0.0.’’
84
2011 Ridgeline10/04/19 15:49:40 31SJC650_090
Outside Temperature
OUTSIDE TEMPERATURE
U.S. model is shown.
This shows the outside temperature in Fahrenheit (U.S. models), or in Celsius (Canadian models).
The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.
In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.
Multi-Information Display
If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.
5°F in U.S. models (
±
The temperature must be
NOTE: stabilized before doing this procedure.
To adjust the outside temperature
indicator, press and hold the SEL/
RESET button for 10 seconds. The
following sequence will appear for 1
second each: 0, 1, 2, 3, 4, 5,
4,
− − −
− − −
− − 1, 0 (U.S.) or 0, 1, 2, 3, 1, 0 (Canada).
2, 2,
3, 3,
5,
When the temperature reaches the desired value, release the SEL/ RESET button. You should see the new outside temperature displayed.
85
2011 Ridgeline10/04/19 15:49:47 31SJC650_091
Multi-Information Display
Engine Oil Life
Tire Pressure Monitor
Bluetooth
HandsFreeLink
U.S.
Canada
ENGINE OIL LIFE
This shows the remaining life of the engine oil. It shows 100% after the engine oil is replaced and the display is reset. The engine oil life is calculated based on engine operating conditions and accumulated engine revolutions. For more information, see page
313
86
When the tire pressure monitor is shown on the multi-information display, press the SEL/RESET button. The display changes as shown. You can see the pressure of each tire in this monitor. If one or more tires are low, inflate them to the correct pressure. For more information, see page
282
You can receive or make phone calls from your cell phone through your HandsFreeLink vehicle’s (HFL) system without touching your cell phone.
Bluetooth
2011 Ridgeline10/04/19 15:49:54 31SJC650_092
Multi-Information Display
To use the system, your cell phone
and the HFL system must be linked.
Not all cell phones are compatible
with this system. Refer to page
for instructions on how to link
221
your cell phone to HFL and how to
receive or make phone calls, or visit
the handsfreelink.com website. In
Canada, visit
, or call
1-(888) 9-HONDA-9.
www.honda.ca
Trip Computer
Average Fuel Economy/Range
Average Vehicle Speed/Elapsed Time
Instantaneous Fuel Economy
U.S. model is shown.
▲ ▼
INFO ( ) button SEL/RESET button
CONTINUED
87
2011 Ridgeline10/04/19 15:50:04 31SJC650_093
Multi-Information Display
Along with the trip meter, the trip computer calculates these values:
Average Fuel Economy Range Average Vehicle Speed Elapsed Time Instantaneous fuel economy
88
ELAPSEDTIMEA/B This shows the accumulated traveling time since you last reset it. When you turn the ignition switch to the ON (II) position, ELAPSED TIME is reset.
INSTANTFUELMPG(U.S. models)/INSTANTFUELL/100km (Canadianmodels) This shows your instant fuel economy.
AVERAGEFUELA/B This shows your vehicle’s average fuel economy in mpg (U.S. models) or liter/100 km (Canadian models) since you last reset Trip A or Trip B.
RANGE This shows the estimated distance you can travel on the fuel remaining in the fuel tank. This distance is estimated from the fuel economy you received over the last several miles (U.S.) or kilometers (Canada), so it will vary with changes in speed, traffic, etc.
AVERAGESPEEDA/B This shows the average speed you are traveling in miles per hour (mph) for U.S. models or kilometers per hour (km/h) for Canadian models.
2011 Ridgeline10/04/19 15:50:11 31SJC650_094
System Messages
SYSTEM MESSAGE INDICATOR
If there is a problem with your vehicle, for example the engine oil level is low or a door is not fully closed, the multi-information display will show you the problem. It does this by interrupting the current display with one or more messages.
The system message(s) triggers the appropriate indicator(s) on the instrument panel, including the system message indicator, to come on. The system message indicator does not go off until the problem(s) is corrected.
You will also hear a beep when the system message comes on for the first time.
Multi-Information Display
When there are several messages to be shown, the system switches the messages every 5 seconds. The message is shown until you push the INFO ( ) button. To see the message again, press the INFO ( after the display disappears.
) button, 5 seconds
▲ ▼
▲ ▼
or
or
Here is a list of messages shown on the multi-information display:
CONTINUED
89
2011 Ridgeline10/04/19 15:50:23 31SJC650_095
Multi-Information Display
U.S.
Canada
See page
132
See page
376
See page
376
See page
374
See page
375
U.S.
Canada
U.S.
Canada
See page
11
See page
20
See page
20
See page
30
See page
31
U.S.
Canada
90
2011 Ridgeline10/04/19 15:50:32 31SJC650_096
Multi-Information Display
See page
374
See page
289
See page
291
See page
281
See page
282
See page
69
See page
271
See page
330
See page
68
See page
97
See page
319
See page
250
91
2011 Ridgeline10/04/19 15:50:39 31SJC650_097
Multi-Information Display
Language Selection
There are three language selections you can make: English, Spanish, and French. To choose the language you want, follow these instructions:
Press and release the INFO ( / ) ▲ ▼ button repeatedly to select the ‘‘LANGUAGE SELECTION’’ display.
Press the SEL/RESET button to see the selections.
Select the desired language by pressing the SEL/RESET button, then enter your selection by pressing and holding the SEL/RESET button.
When your selection is successfully completed, the display returns to the ‘‘LANGUAGE SELECTION’’ display.
92
2011 Ridgeline10/04/19 15:50:50 31SJC650_098
Controls Near the Steering Wheel
TRIP/RESET BUTTON * (P.76)
SELECT BUTTON
*
(P.76)
SHIFT LEVER (P.271) VTM-4 LOCK (P.276)
INSTRUMENT PANEL BRIGHTNESS (P.98)
MOONROOF SWITCH * (P.131)
MULTI-CONTROL LEVER (WINDSHIELD WIPERS/ WASHERS/TURN SIGNALS/ HEADLIGHT HIGH BEAMS) (P.94)
REMOTE AUDIO CONTROLS * (P.203)
HEADLIGHT CONTROL DIAL (P.95) FOG LIGHTS
(P.97)
*
VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH
(P.292)
BED LIGHT SWITCH (P.144)
VOICE CONTROL BUTTONS
*
Vehicle with navigation system is shown.
BLUETOOTH HANDSFREELINK SYSTEM VOICE CONTROL BUTTONS
(P.221)
*
* * * * *
1 : 2 : 3 : 4 : 5 :
To use the horn, press the center pad of the steering wheel. If equipped Only on vehicles equipped with navigation system. Refer to the navigation system manual. On models with navigation system. On models without navigation system.
*
▲
) BUTTON
INFO ( (P.76) SEL/RESET BUTTON * (P.76) INFO ( (P.76) PASSENGER AIRBAG OFF INDICATOR
) BUTTON
(P.31)
▼
*
HAZARD WARNING BUTTON (P.99)
CRUISE CONTROLS (P.210) INTERIOR LIGHT CONTROL SWITCH
(P.142)
SEAT HEATERS (P.126)
*
HORN STEERING WHEEL ADJUSTMENT
(P.99)
*
93
2011 Ridgeline10/04/19 15:50:59 31SJC650_099
Multi-Control Lever
1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
OFF INT: Intermittent INT TIME ring LO: Low speed HI: High speed MIST Windshield washers Turn signal High beams Flash high beams
94
The multi-control lever has many functions, including windshield wipers and washers, turn signals, headlight high beams, and headlight high beam flashing.
To select a position, turn the rotary switch, push the button on the end of the lever, or push the lever up, down, forward, or backward.
OFF:
The wipers are not activated.
INT:
The length of the wiper
interval is varied automatically according to the vehicle’s speed.
Vary the delay by turning the INT TIME ring. If you turn it to the shortest delay, the wipers change to low speed when the vehicle speed exceeds 12 mph (20 km/h).
LO
−
The wipers run at low speed.
HI
−
The wipers run at high speed.
MIST:
The wipers run at high speed
until you release the lever.
Windshield Washer:
Push the button on the end of the multi- control lever. The washers spray until you release the button. The wipers run at low speed, then complete one more sweep after you release the button.
2011 Ridgeline10/04/19 15:51:07 31SJC650_100
AutomaticHeatedWiperZone Your vehicle has heating wires at the bottom of the windshield to help heat the wiper blades and the windshield. If the outside temperature is near freezing, the heater turns on automatically when you turn the ignition switch to the ON (II) position. The heater turns off automatically when the outside temperature is above freezing.
This function helps to increase wiper performance when the wiper arms sit in the parked position in snowy or icy conditions.
Multi-Control Lever, Headlights
Headlight Control Dial
−
Turn Signal Push down on the multi-control lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to center when you release it or complete a turn.
−
High Beams To turn on the high beams, push the multi-control lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.
). Pull the lever back
67
To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.
1. 2. 3.
OFF Parking and indicator lights Headlights
CONTINUED
95
2011 RidgelineAutomatic Lighting Off Feature The automatic lighting off feature turns off the headlights, all other exterior lights, and the instrument panel lights within 15 seconds of removing the key from the ignition switch and closing the driver’s door.
This feature activates if you leave the headlight control dial in the ‘‘ the key, then open and close the driver’s door.
’’ position, remove
’’ or ‘‘
If you remove the key from the
ignition switch with the headlight
control dial on, but do not open the
door, the lights will turn off after 10
minutes.
The lights will turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights go off. With the driver’s door open, you will hear a lights-on reminder chime.
10/04/19 15:51:14 31SJC650_101
Headlights
−
Turning the dial to ’’ position turns on the
Headlights the ‘‘ parking lights, taillights, instrument panel lights, and license plate lights.
’’
Turning the dial to the ‘‘ position turns on the headlights. If you leave the lights on and remove the key from the ignition switch, you will hear a reminder chime when you open the driver’s door.
’’ or
’’ position, the lights on
When the dial is in the ‘‘ ‘‘ indicator comes on as a reminder. This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.
96
2011 Ridgeline10/04/19 15:51:21 31SJC650_102
Headlights, Fog Lights
Daytime Running Lights With the headlight control dial off, the daytime running lights come on when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.
The headlights revert to normal operation when you turn them on with the headlight control dial.
Onmodelswithnavigationsystem If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem with the daytime running light circuit. Take your vehicle to a dealer to have it checked.
Fog Lights Ifequipped
Turn the fog lights on and off by pressing the button. The indicator in the button lights to show the fog lights are on.
You can use the fog lights only when the headlights are on low beam.