To lock any passenger’s door when getting out of the vehicle, push the lock tab down, and close the door. To lock the driver’s door, remove the key from the ignition switch, and push the lock tab down, or push the front of the master switch, then close the door.
LockoutPrevention With the driver’s door open and the key in the ignition, both master door lock switches will not lock, but they will unlock. The lock feature is not disabled if the driver’s door is closed. Pushing the front of the switch on the open passenger’s door will lock all doors and the In-Bed Trunk.
This vehicle has auto door locking/ unlocking features. See page for how to set them.
84
83
2008 Ridgeline 07/04/27 13:51:47 31SJC620 0089
Auto Door Locking/Unlocking Your vehicle has customizable settings for the doors to automatically lock and unlock. There are default settings for each of these features. You can turn off or change the settings for these features as described on the following pages. When you customize the setting, make sure your vehicle is parked in safe, the engine is off, and apply the parking brake. Make all settings before you start driving.
With the auto door locking and unlocking, the In-Bed Trunk also locks and unlocks.
Auto Door Locking The auto door locking feature has three possible settings:
The auto door locking is deactivated all the time.
The doors lock whenever you move the shift lever out of the Park (P) position.
The doors lock when the vehicle speed reaches 9 mph (15 km/h). This is the default setting.
Door Locks
Childproof Door Locks
LOCK LEVER
The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from inside regardless of the position of the lock tab. To open the door, pull the lock tab up, and use the outside door handle.
84
2008 Ridgeline 07/04/27 13:51:56 31SJC620 0090
ToturnofftheAutoDoorLock modes:
3.
Push and hold the front of the master door lock switch on the driver’s door until you hear a click (after about 5 seconds).
4.
Release the switch and, within 5
seconds, turn the ignition switch
to the LOCK (0) position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and open the driver’s door.
Door Locks
ToprogramtheParkLockmode: Locksalldoorswhentheshiftleveris movedoutofthePark(P)position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
CONTINUED
85
2008 Ridgeline 07/04/27 13:52:06 31SJC620 0091
Door Locks
3.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a click.
Keep holding the switch until you
hear another click (after about 5
seconds).
4.
Release the switch and, within 5
seconds, turn the ignition switch
to the LOCK (0) position.
ToprogramtheDriveLockmode: Locksalldoorswhenthevehicle’sspeed reachesabout9mph(15km/h).
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
86
3.
4.
Push and hold the brake pedal, and move the shift lever out of the Park (P) position.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a click.
Keep holding the switch until you
hear another click (after about 5
seconds).
5.
Release the switch and, within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
Move the shift lever to the Park
(P) position.
6.
Turn the ignition switch to the LOCK (0) position.
2008 Ridgeline 07/04/27 13:52:17 31SJC620 0092
Auto Door Unlocking The auto door unlocking feature has five possible settings:
ToturnofftheAutoDoorUnlock modes:
The auto door unlocking is deactivated all the time.
The driver’s door unlocks when you move the shift lever to the Park (P) position. This is the default setting.
All doors unlock when you move the shift lever to the Park (P) position.
The driver’s door unlocks whenever you turn the ignition switch to the ACCESSORY (I) position.
All doors unlock whenever you turn the ignition switch to the ACCESSORY (I) position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and open the driver’s door.
Door Locks
3.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click and, after about 5 seconds, you will hear another click.
4.
Release the switch and, within 5
seconds, turn the ignition switch
to the LOCK (0) position.
CONTINUED
87
2008 Ridgeline 07/04/27 13:52:28 31SJC620 0093
Door Locks
ToprogramtheParkUnlockmode: Unlocksthedriver’sdoororalldoors whentheshiftleverismovedintothe Park(P)position.
3.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold down the switch:
−
Until you hear another click (after about 5 seconds) to activate the driver’s door unlock feature.
−
Or, until you hear two more clicks (after about 10 seconds) to activate the all doors unlock feature.
4.
Release the switch and, within 5
seconds, turn the ignition switch
to the LOCK (0) position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
88
ToprogramtheIgnitionSwitch Unlockmode: Unlocksthedriver’sdoororalldoors whentheignitionswitchismovedoutof theON(II)position.
1.
Make sure the shift lever is in the Park (P) position.
2.
Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.
2008 Ridgeline 07/04/27 13:52:35 31SJC620 0094
5.
Release the switch and, within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
Move the shift lever to the Park
(P) position.
6.
Turn the ignition switch to the LOCK (0) position.
3.
4.
Push and hold the brake pedal, then move the shift lever out of the Park (P) position.
Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold down the switch:
−
Until you hear another click (after about 5 seconds) to activate the driver’s door unlock feature.
−Or, until you hear two more
clicks (after about 10 seconds) to activate the all doors unlock feature.
Door Locks
If your vehicle’s battery is removed or goes dead, the auto door lock/ unlock setting is reset to the deactivated mode.
89
2008 Ridgeline 07/04/27 13:52:42 31SJC620 0095
Remote Transmitter
LED
LOCK BUTTON
UNLOCK BUTTON
PANIC BUTTON
−
LOCK
Press this button once to
lock all doors and the In-Bed Trunk.
Some exterior and interior lights will
flash once.
When you push LOCK twice within 5
seconds, you will hear a beep to
verify that the doors and In-Bed
Trunk are locked and the security
system (if equipped) has set. This
button does not work if any door is
not fully closed or the key is in the
ignition switch.
90
−
Press this button once
UNLOCK to unlock the driver’s door and the In-Bed Trunk. Push it twice to unlock the remaining doors. Some exterior and interior lights will flash twice each time you push the button.
When you press the UNLOCK button, the front and rear individual map lights, depending on the interior light control switch position, will come on (see page not open any door, the lights stay on for about 30 seconds, then go out. If you relock the doors and the In-Bed Trunk with the remote transmitter before 30 seconds have elapsed, the lights will go off immediately.
). If you do
120
If you do not open any door within 30
seconds, the doors automatically
relock, and the security system sets
(if equipped). The UNLOCK button
does not work when the key is in the
ignition switch.
You can also open all side windows
from outside the vehicle with the
109
remote transmitter (see page
).
−
Press and hold this
PANIC button for about 1 second to attract attention; the horn will sound and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position. Panic mode does not work when the key is in the ignition switch.
2008 Ridgeline 07/04/27 13:52:53 31SJC620 0096
Remote Transmitter Care
Avoid dropping or throwing the transmitter.
Protect the transmitter from extreme temperature.
Do not immerse the transmitter in any liquid.
If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
Remote Transmitter
Replacing the Transmitter Battery
BATTERY
SCREW
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR1616
2.
3.
To replace the battery:
1.
Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.
Separate the transmitter by prying its middle seam with your fingernail.
Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.
CONTINUED
91
2008 Ridgeline 07/04/27 13:52:59 31SJC620 0097
Remote Transmitter
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
4.
Remove the old battery from the back of the inner cover, and insert a new battery into the back of the cover with the
side facing down.
+
An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.
5.
Install the parts in reverse order.
92
2008 Ridgeline 07/04/27 13:53:07 31SJC620 0098
Before you open the tailgate a different way (dropped open, and then swung open), make sure it is fully closed.
Make sure all passengers and objects are clear of the tailgate before opening and closing it, and make sure the tailgate is closed securely before driving.
You can open the tailgate two different ways:
Drop it open by using the upper handle.
Swing it open by using the right lower handle.
NOTE: As a safety feature, the upper handle is disabled if you do not fully close the tailgate after it is swung open. And the lower handle is disabled if you do not fully close the tailgate after it is dropped open.
Dual-Action Tailgate
To Drop Open the Tailgate
UPPER HANDLE
To drop open the tailgate, pull up the upper handle, then pull down the tailgate. To close the tailgate, push firmly up until it latches.
CONTINUED
93
2008 Ridgeline 07/04/27 13:53:14 31SJC620 0099
Dual-Action Tailgate
The dropped open tailgate can be used as an extended pickup bed. Make sure to secure the items in the pickup bed, and do not exceed the maximum allowable weight on the tailgate (see page
194
).
To Swing Open the Tailgate
To turn the bed lights on or off, use the bed light switch on the dashboard (see page ).
122
HANDLE
To swing open the tailgate, first make sure it is fully closed, then pull up the right lower handle, and swing the tailgate to the left. To close, swing the tailgate back, and push it firmly until it is latched.
Before opening or closing the tailgate, check that passengers, especially children, are not in the tailgate’s path.
94
Do not drive with the tailgate swung open. This could damage the tailgate.
Swinging the tailgate open or closed while anyone is in its path can cause serious injury.
Make sure all passengers are clear of the tailgate’s path before opening or closing it.
2008 Ridgeline 07/04/27 13:53:23 31SJC620 0100
Do not allow anyone to hang on the swung open tailgate. This could damage the tailgate.
Do not leave the tailgate swung open. The tailgate may swing and shut accidentally. This could cause serious injuries.
The bed lights come on when you swing open the tailgate. You can also turn the bed lights on or off by pushing the bed light switch on the dashboard (see page
122
).
TailgateOpenIndicator
This indicator is in the door and tailgate open monitor on the instrument panel. It comes on when the tailgate is swung open or it is not completely closed. This indicator works even if the key is not in the ignition switch.
If the tailgate is swung open or not closed tightly when the ignition switch is in the ON (II) position, you will hear six beeps and see the indicator blinking. The indicator stays on until you close the tailgate. The beeper also sounds and the indicator blinks when you move the shift lever out of the Park or neutral position.
Dual-Action Tailgate
If you do not fasten the seat belt, you first hear the seat belt reminder alarm, then the tailgate reminder beeper sounds.
The indicator does not monitor the tailgate when it is dropped open.
Loading Cargo See page for information on cargo loading and weight limits.
190
You can also store and lock items in the In-Bed Trunk (see page
96
).
95
2008 Ridgeline 07/04/27 13:53:32 31SJC620 0101
In-Bed Trunk
TM
If your vehicle’s battery is disconnected or goes dead, the release button on the In-Bed Trunk lid is disabled. To open the In-Bed Trunk, use the master key.
The bed lights come on when you open the In-Bed Trunk. You can also turn the bed lights on or off by pushing the bed light switch on the dashboard (see page
122
).
You can store items in the In-Bed
Trunk up to 300 lbs (136 kg). Do not
exceed this weight limit, or you may
damage the In-Bed Trunk. See page
190
for information on loading cargo
and weight limits.
To store items separately in the In-Bed Trunk, optional divider guides are available from your dealer.
To close the In-Bed Trunk, lower the lid, then press down on the back edge.
When the In-Bed Trunk is closed securely, it can be locked or unlocked along with the power door locks (see page
83
).
RELEASE BUTTON
You can open the In-Bed Trunk two different ways:
Push the release button on the lower right side of the In-Bed Trunk lid when the driver’s door is unlocked.
Use the master key to open the In-Bed Trunk when the driver’s door is locked.
96
2008 Ridgeline 07/04/27 13:53:40 31SJC620 0102
To avoid damaging the key and key cylinder of the In-Bed Trunk lid, do not close the tailgate when the key is in the lid.
To avoid damaging the seal on the In-Bed Trunk lid, remove any debris from the lid’s mating surface before you close it.
Emergency Opener
In-Bed Trunk
TM
To avoid damaging the In-Bed Trunk lid, and to prevent items from being thrown about the vehicle and possibly hurting someone in an accident or sudden stop, be sure the In-Bed Trunk lid is securely closed before driving away.
To avoid damaging the bottom of the In-Bed Trunk, do not drive over large obstacles, and do not use it as a jacking point to raise the vehicle.
In-Bed Trunk Open Indicator
This indicator on the instrument panel reminds you that the In-Bed Trunk is open (see page
69
).
RELEASE LEVER
As a safety feature, your vehicle has a release lever on the latch of the In-Bed Trunk lid so it can be opened from the inside. To open the In-Bed Trunk, push the release lever in the direction of the arrow.
Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page
36
97
2008 Ridgeline 07/04/27 13:53:48 31SJC620 0103
In-Bed Trunk
TM
In-Bed Trunk Main Switch
Washing the In-Bed Trunk
Cargo Hooks
MAIN SWITCH
CARGO HOOKS
To protect items in the In-Bed Trunk, you can disable its release button by turning off the main switch in the glove box and locking the glove box with the master key.
Even if the main switch is in the OFF position, you can open the In-Bed Trunk with the master key.
98
DRAIN PLUG
You can wash the inside of the In-Bed Trunk with a water and mild detergent solution, and a soft brush or cloth.
To drain water from the In-Bed Trunk, remove the drain plug by turning it counterclockwise.
When you are finished washing the In-Bed Trunk, dry it with a soft cloth, and reinstall the drain plug.
There are two cargo hooks for plastic grocery bags at the back of the In-Bed Trunk. They are designed to hold light items. Heavy objects may damage the hooks.
2008 Ridgeline 07/04/27 13:53:55 31SJC620 0104
The front passenger’s seat in all models adjusts manually.
−
11 13
Manual Seat Adjustments OnRT,RTX,andCanadianLXmodels Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs. Make all seat adjustments before you start driving.
To adjust the seat forward or backward, pull up on the bar under the seat cushion’s front edge. Move the seat to the desired position, and release the bar. Try to move the seat
Seats
to make sure it is locked in position.
To change the seat-back angle of the front seat, pull up the lever on the outside of the seat bottom.
Once a seat is adjusted correctly, rock it back and forth to make sure it is locked in position.
99
2008 Ridgeline 07/04/27 13:54:02 31SJC620 0105
Seats
Driver’s Seat Manual Height Adjustment Make all seat adjustments before you start driving.
OnRT,RTX,andCanadianLXmodels The height of your driver’s seat is adjustable. To raise the seat, repeatedly pull up the lever on the outside of the seat cushion. To lower the seat, push the lever down repeatedly.
100
Make sure to pull the lever upward or downward to its full range.
Driver’s Manual Lumbar Support
OnRTSmodel Vary the lumbar support by moving the lever on the right side of the seat-back. Move the lever forward or backward to adjust the lumbar support through its full range.
2008 Ridgeline 07/04/27 13:54:13 31SJC620 0106
Power Seat Adjustments OnRTS,RTL,andCanadianEXL models Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.
11 13
−
The controls for the power adjustable driver’s seat are on the outside edge of the seat bottom. You can adjust the seat with the ignition switch in any position. Make all seat adjustments before you start driving.
Moving the long horizontal switch adjusts the seat bottom in several directions. The seat bottom adjusts in the direction you move the switch. The short vertical switch adjusts the seat-back angle.
Moves the seat forward and backward.
Moves the front of the seat up or down.
Raises or lowers the seat.
Seats
Moves the whole seat up and forward, or down and backward. The front of the seat also tilts up or down at the same time.
Adjusts the seat-back angle forward or backward.
Increases or decreases the lumbar support. (RTL and Canadian EXL models)
101
2008 Ridgeline 07/04/27 13:54:21 31SJC620 0107
Seats
Armrests
FRONT
REAR
To use the console lid as an armrest, slide it to the desired position.
Make sure your passenger’s hands or fingers are away from the armrest before moving it.
The rear seat armrest is in the center of the rear seats. Pivot it down to use it.
102
Head Restraints Seepage forimportantsafety informationandawarningabout improperlypositioningheadrestraints.
13
Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from whiplash and other injuries.
2008 Ridgeline 07/04/27 13:54:26 31SJC620 0108
Seats
Rear Center Position
They are most effective when you adjust them so the center of the back of the occupant’s head rests against the center of the restraint.
RELEASE BUTTON
RELEASE BUTTON
The head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways, and push the restraint down.
When a passenger is seated in the rear center seating position, make sure the center head restraint is properly positioned.
CONTINUED
103
2008 Ridgeline 07/04/27 13:54:32 31SJC620 0109
Seats
Failure to reinstall the head restraints can result in severe injury during a crash.
Always replace the head restraints before driving.
Folding the Rear Seats The left and right rear seat cushions can be lifted up separately to make room for cargo.
Remove any items from the seat before you fold up the seat cushion.
To fold a rear seat cushion, pull up the lever on the outside of the cushion. The seat cushion pops up, and the seat legs store underneath it. Push the cushion firmly against the seat-back to lock it in place.
104
2008 Ridgeline 07/04/27 13:54:40 31SJC620 0110
Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have Carrying Cargo to brake hard (See on page
190
).
You can also store small items under the rear seats. Make sure to secure the items so they will not shift while you are driving.
LEGS
FLOOR GUIDE
To return the seat cushion to its original position, pull the lever outward, then push down the seat cushion slowly.
Make sure the seat cushion is locked securely and the seat legs are positioned properly in the floor guide.
Seats, Seat Heaters
Seat Heaters
Passenger’s Seat
HEATERS
Driver’s Seat
Ifequipped Both front seats are equipped with seat heaters. The passenger seat is only heated in the seat bottom because of the side airbag cutoff system.
CONTINUED
105
2008 Ridgeline 07/04/27 13:54:47 31SJC620 0111
In the HI setting, the heater turns off when the seat gets warm, and turns back on after the seat’s temperature drops.
In the LO setting, the heater runs continuously. It does not cycle with temperature changes.
Follow these precautions when using the seat heaters:
Use the HI setting only to heat the seats quickly, because it draws large amounts of current from the battery.
If the engine is left idling for an extended period, do not use the seat heaters, even on the LO setting. It can weaken the battery, causing hard starting.
Seat Heaters
SEAT HEATER SWITCHES
The ignition switch must be in the ON (II) position to use seat heaters. Push the top of the switch, HI, to rapidly heat up the seat. After the seat reaches a comfortable temperature, select LO by pushing the bottom of the switch. This will keep the seat warm.
106
2008 Ridgeline 07/04/27 13:54:53 31SJC620 0112
Power Windows
DRIVER’S WINDOW SWITCH
MAIN SWITCH
The windows operate for up to 10
minutes after you turn off the
ignition switch. Opening either front
door cancels this function.
BACK WINDOW SWITCH
Closing a power window on someone’s hands or fingers can cause serious injury.
Make sure your passengers are away from the windows before closing them.
Turn the ignition switch to the ON (II) position to raise or lower any side window, or open and close the back window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Pull back on the switch and hold it to close the window.
−
To open or close the
AUTO driver’s window, push or pull the window switch firmly down or up to the second detent, and release it. The window will automatically go up or down all the way. To stop the window, pull or push the window switch briefly.
When you push the MAIN switch in, the passenger windows and the back window cannot be raised or lowered.
To cancel this feature, push on the switch again. Keep the MAIN switch off when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally.
CONTINUED
107
2008 Ridgeline 07/04/27 13:55:02 31SJC620 0113
Power Windows
AUTO REVERSE − If the driver’s window senses any obstacle while it is closing automatically, it will reverse direction, and then stop. To close the window, remove the obstacle, then use the window switch again.
Auto reverse stops sensing when the window is almost closed. You should always check that all passengers and objects are away from the window before closing it.
If the driver’s window fuse is removed, the AUTO function may be disabled. The power window system needs to be reset after reinstalling the fuse.
1.
2.
Start the engine. Push down and hold the driver’s window switch until the window is fully open.
Pull and hold the driver’s window switch to close the window completely, then hold the switch for about 2 seconds.
If the power windows do not operate properly after resetting, have your vehicle checked by your dealer.
Back Window Your vehicle has a power back window.
Back Window Open Indicator
This indicator comes on when you
turn the ignition switch from the ON
(II) position to the ACCESSORY (I)
or LOCK (0) position without closing
the back window. With the ignition
switch in the ACCESSORY (I)
position, the indicator goes off after
about 30 seconds. With the ignition
switch in the LOCK (0) position, the
indicator goes off after about 3
minutes.
108
2008 Ridgeline 07/04/27 13:55:13 31SJC620 0114
If you remove the ignition key and
open the driver’s door without
closing the back window, you hear
five beeps and see the indicator blink.
If you do not close the back window
before the beeper stops, the
indicator stops blinking but remains
on. It will go off after about 3
minutes (see page
69
).
The back window is not designed to carry long items through it. Do not use the opened back window as a cargo area pass-through.
Opening the Side Windows with the Remote Transmitter You can open all of the side windows from the outside with the remote transmitter.
1.
Press the UNLOCK button once to unlock the driver’s door.
2.
Press the UNLOCK button a second time, and hold it. The passenger’s doors unlock, and all four side windows start to open. To stop the windows, release the button.
3.
To open the windows further, press the button again, within about 3 seconds.
You cannot close the windows with the remote transmitter.
Power Windows
UNLOCK BUTTON
Close
Open
Opening/Closing the Side Windows with the Key You can open and close the side windows with the key in the driver’s door lock.
To open: 1.
Insert the key in the driver’s door lock.
2.
Turn the key clockwise, then release it.
CONTINUED
109
2008 Ridgeline 07/04/27 13:55:23 31SJC620 0115
Power Windows, Moonroof
3.
Turn the key clockwise again, and hold it. All four side windows start to open. To stop the windows, release the key.
4.
To open the windows further, turn and hold the key again (within 10 seconds).
NOTE: If the windows stop before
the desired position, repeat steps 2
and 3.
To close: 1.
Insert the key in the driver’s door lock.
2.
Turn the key counterclockwise, then release it.
3.
Turn the key counterclockwise again, and hold it. All four side windows start to close. To stop the windows, release the key.
110
4.
To close the windows further, turn and hold the key again (within 10 seconds).
Moonroof
NOTE: If the windows stop before
the desired position, repeat steps 2
and 3.
MOONROOF SWITCH
Ifequipped The moonroof has two positions: it can be tilted up in the back for ventilation, or it can slide back into the roof. Use the switch near the left dashboard vent to operate the moonroof. The ignition switch must be in the ON (II) position.
2008 Ridgeline 07/04/27 13:55:32 31SJC620 0116
). To close the
To tilt up the back of the moonroof, press and hold the center part of the switch ( moonroof, press and hold the upper part of the switch ( ). To open the moonroof, press and hold the lower part of the switch ( ). Release the switch when the moonroof gets to the desired position.
Make sure everyone’s hands are away from the moonroof before opening or closing it.
Opening or closing the moonroof on someone’s hands or fingers can cause serious injury.
Make sure all hands and fingers are clear of the moonroof before opening or closing it.
Moonroof, Parking Brake
You can open and close the moonroof for up to 10 minutes after you turn off the ignition switch. Opening either front door cancels this function.
Parking Brake
RELEASE HANDLE
If you try to open the moonroof in below-f reezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or its motor.
PARKING BRAKE PEDAL
To apply the parking brake, push the pedal down with your foot. To release it, pull the release handle fully. The parking brake indicator on the instrument panel should go out when the parking brake is fully released, and the ignition switch is in the ON (II) position (see page
63
).
CONTINUED
111
2008 Ridgeline Ifequipped The rear view mirror has a compass function to indicate the vehicle’s direction. Refer to
Compass
on page
172
07/04/27 13:55:39 31SJC620 0117
Parking Brake, Mirrors
Driving the vehicle with the parking brake applied can damage the rear brakes and axles. A beeper will sound if the vehicle is driven with the parking brake on.
Mirrors
TAB
Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.
The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.
112
2008 Ridgeline 07/04/27 13:55:47 31SJC620 0118
AdjustingthePowerMirrors
ADJUSTMENT SWITCH
4.
When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings.
HeatedMirrors
HEATED MIRROR BUTTON
Mirrors
1.
2.
3.
SELECTOR SWITCH Turn the ignition switch to the ON (II) position.
Move the selector switch to L (driver’s side) or R (passenger’s side).
Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down.
Ifequipped The outside mirrors are heated to remove fog and frost. With the ignition switch in the ON (II) position, turn on the heaters by pressing the button. The indicator in the button comes on as a reminder. Press the button again to turn the heaters off.
113
2008 Ridgeline 07/04/27 13:55:52 31SJC620 0119
Interior Convenience Items
VANITY MIRROR
SUN VISOR
CENTER CONSOLE
CONSOLE COMPARTMENT
SUNGLASSES HOLDER
CENTER UPPER POCKET *
GLOVE BOX
ACCESSORY POWER SOCKETS CENTER POCKET
BEVERAGE HOLDER
COAT HOOK
ACCESSORY POWER SOCKET
CENTER LOWER POCKET
BEVERAGE HOLDERS
*
: On vehicle without navigation system
114
2008 Ridgeline 07/04/27 13:56:00 31SJC620 0120
Center Console
ConsoleCompartments The center console main compartment is under the tray and the beverage holder. You can access the main compartment in two ways (front or rear).
Your vehicle has a multi-function center console. It includes beverage holders, storage compartments, an armrest, a coin holder, and a storage tray.
To open the front of the compartment, squeeze the knob, and push it forward while sliding the beverage holder. To close, squeeze the knob and pull the compartment backward until the beverage holder latches.
Interior Convenience Items
To open the rear of the compartment, push the button at the end of the tray, then slide the tray forward. To close, slide the tray back in place.
There are two removable partitions in the main compartment. The partitions can be used to divide the main compartment, or can be stored at the front of the compartment. The console compartment light comes on when the instrument panel lights are on. CONTINUED
115
2008 Ridgeline 07/04/27 13:56:09 31SJC620 0121
Interior Convenience Items
CargoHooks
CARGO HOOKS
There are two cargo hooks for plastic grocery bags at the back of the center console. They are designed to hold light items. Heavy objects may damage the hooks.
COIN HOLDER
You can put small items in the upper console compartment. To use it, pull up on the lever and lift up the armrest.
Ifequipped The upper console compartment has a removable coin holder. Pull the coin holder straight up to remove it. To install it, push it down along the guides on the side of the compartment.
116
Beverage Holders The center console has two beverage holders on the front. Your vehicle also has beverage holders in the rear seat armrest and the rear door panels.
Be careful when you are using the beverage holders. A spilled liquid that is very hot can scald you or your passengers. Liquid can also spill from the door panel beverage holders when you close the doors. Use only resealable containers in the door beverage holders.
Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior.
2008 Ridgeline 07/04/27 13:56:17 31SJC620 0122
Glove Box Open the glove box by pulling up on the handle. Close it with a firm push. Lock or unlock the glove box with the master key.
The glove box light comes on when the parking lights are on.
An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.
Always keep the glove box closed while driving.
Interior Convenience Items
Coat Hooks
Sunglasses Holder
SUNGLASSES HOLDER
These hooks are not designed for large or heavy items.
To open the sunglasses holder, push on the rear edge. Make sure the holder is closed while you are driving.
Some larger styles of sunglasses may not fit in the holder.
117
2008 Ridgeline 07/04/27 13:56:24 31SJC620 0123
Interior Convenience Items
Accessory Power Sockets
FRONT
REAR
None of the sockets will power an automotive type cigarette lighter element. When both sockets are being used, the combined power rating of the accessories should be 120 watts or less (10 amps).
There are three accessory power sockets in your vehicle. Two accessory power sockets are above the center pocket on the dashboard, and another is on the back of the center console.
These sockets are intended to supply
power for 12 volt DC accessories
that are rated 120 watts or less (10
amps).
To use an accessory power socket, the ignition switch must be in the ACCESSORY (I) or ON (II) position.
118
2008 Ridgeline 07/04/27 13:56:31 31SJC620 0124
Sun Visor
Make sure you put the sun visor back in place when you are getting into or out of the vehicle.
Vanity Mirror
Interior Convenience Items
SUN VISOR
To use the sun visor, pull it down. When using the sun visor for the side window, remove the support rod from the clip, and swing it out.
In this position, the sun visor can be adjusted by moving it on its slider. Do not use the extended sun visor over the inside mirror.
Pull up the vanity mirror cover to use it.
The light comes on when you pull up the cover.
The light will not come on if the sun visor is slid outward.
119
2008 Ridgeline 07/04/27 13:56:39 31SJC620 0125
Interior Lights
Interior Light Control Switch
Whentheswitchisinthedoorposition:
WhentheswitchisintheOFFposition:
None of the lights come on when a door is opened.
The map lights in the front can be turned on and off by pushing each lens. The rear map lights cannot be used.
The individual map lights and the rear console light come on when any door is opened, or when the remote transmitter or the key is used to unlock the doors. When the doors are closed, each individual map light can be turned on and off by pushing the lens.
The lights fade out about 30
seconds after all the doors are
closed.
With any door left open and the
key removed from the ignition
switch, the lights stay on about 3
minutes, then go out.
DOOR POSITION
ON
OFF
Whentheinteriorlightcontrolswitchis intheONposition:
All the individual map lights and the rear console light come on and stay on as long as the switch remains in the ON position.
120
2008 Ridgeline 07/04/27 13:56:47 31SJC620 0126
Individual Map Lights Turn on a front individual map light by pushing the lens. Push the lens again to turn it off. With the interior light control switch in the door position, a rear map light can be turned on by pushing the lens. Push the lens again to turn it off.
The map lights stay on when the interior light control switch is in the door position and the map light switch is on.
Individual Interior Lights The courtesy light in each door comes on when you open that door. The light around the ignition switch only comes on when you open the driver’s door. After you close the door, the ignition switch light fades out in about 30 seconds.
The courtesy light in the back of the center console comes on when you open any door with the interior light control switch in the door position. After you close the doors, the light fades out.
Interior Lights
Courtesy Light
Ifequipped The courtesy light between the front map lights comes on when you turn the parking lights on. To adjust its brightness, turn the instrument panel brightness control dial on the dashboard (see page
78
).
121
2008 Ridgeline If you turn the ignition switch to
ACCESSORY (I) or LOCK (0)
without turning off the bed lights,
the lights and the indicator will
remain on, then go off after 20
minutes (see page
69
).
07/04/27 13:56:54 31SJC620 0127
Bed Lights
BED LIGHT SWITCH
To turn off the lights, push the light switch again, or close the tailgate and the In-Bed Trunk.
When you move the shift lever out of the Park position, the bed lights go off and cannot be used.
Your vehicle has bed lights in the pickup bed: a light on each front upper and rear bottom side. With the shift lever in the Park position, the bed lights come on when you push the bed light switch on the dashboard, swing open the tailgate, or open the In-Bed Trunk. The indicator on the instrument panel also comes on to remind you that the bed lights are on.