2008 Honda Ridgeline Owners Manual

Donotletachildputtheshoulder partofaseatbeltbehindtheback orunderthearm. cause very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.

Twochildrenshouldneverusethe sameseatbelt. could be very seriously injured in a crash.

If they do, they

52

2008 Ridgeline ０７／０４／２７　１３：４７：２５　３１ＳＪＣ６２０　００５８　

Your vehicle’s exhaust contains carbon monoxide gas. Carbon monoxide should not enter the vehicle in normal driving if you maintain your vehicle properly and follow the information on this page.

Have the exhaust system inspected for leaks whenever:

The vehicle is raised for an oil change.

You notice a change in the sound of the exhaust.

The vehicle was in an accident that may have damaged the underside.

Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you.

Avoid any enclosed areas or activities that expose you to carbon monoxide.

High levels of carbon monoxide can collect rapidly in enclosed areas, such as a garage. Do not run the engine with the garage door closed. Even with the door open, run the engine only long enough to move the vehicle out of the garage.

Carbon Monoxide Hazard

With a truck cap installed and the back window open, engine exhaust may enter the vehicle and cause a hazardous condition. Keep the back window tightly closed whenever you drive with a truck cap installed.

If you must sit in your parked vehicle with the engine running, even in an unconfined area, adjust the heating and cooling system/climate control system as follows:

1. 2. 3. 4.

Select the fresh air mode. Select the Turn the fan on high speed. Set the temperature control to a comfortable setting.

mode.

53

2008 Ridgeline ０７／０４／２７　１３：４７：４１　３１ＳＪＣ６２０　００５９　

Safety Labels

These labels are in the locations shown. They warn you of potential hazards that could cause serious injury or death. Read these labels carefully.

If a label comes off or becomes hard to read (except for the U.S. dashboard label which may be removed by the owner), contact your dealer for a replacement.

RADIATOR CAP

54

DASHBOARD U.S.modelsonly

SUN VISORS U.S.models

Canadianmodels

SUN VISOR U.S.modelsonly

2008 Ridgeline ０７／０４／２７　１３：４８：０２　３１ＳＪＣ６２０　００６０　

HOOD U.S.models

Canadianmodels

Safety Labels

DOORJAMBS U.S.models

Canadianmodels

PICKUP BED U.S.models

Canadianmodels

55

2008 Ridgeline ０７／０４／２７　１３：４８：０５　３１ＳＪＣ６２０　００６１　

56

2008 Ridgeline ０７／０４／２７　１３：４８：０８　３１ＳＪＣ６２０　００６２　

Instruments and Controls

This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach.

Control Locations Instrument Panel Instrument Panel Indicators Gauges Controls Near the Steering

........................... ............................ .......... .............................................

. 58
. 59
. 61
. 70

Wheel

Multi-Control Lever Headlight Control Dial Instrument Panel Brightness Hazard Warning Button Steering Wheel Adjustment Keys Immobilizer System Ignition Switch Door Locks

........................................... . 74
........................ . 75
................... . 76
........ . 78
................. . 79
.......... . 79
.................................................. . 80
........................ . 81
................................ . 82
...................................... . 83
.............. Childproof Door Locks . 84
Auto Door Locking/Unlocking . 84
. 90
....................... . 93
....................... ............................... . 96
................................................. . 99
. 105
.................................. . 107
............................ . 110
....................................... ............................... . 111
. 112
...........................................

Remote Transmitter Dual-Action Tailgate In-Bed Trunk Seats Seat Heaters Power Windows Moonroof Parking Brake Mirrors

TM

Interior Convenience Items

Center Console

Console Compartments Cargo Hooks

......... ......................... ....... ......................... ..................... .................................. ................................ .................... ........ ................................... ............................ ............................... .....................................

Beverage Holders Glove Box Coat Hooks Sunglasses Holder Accessory Power Sockets Sun Visor Vanity Mirror

Interior Lights Bed Lights

. 114
. 115
. 115
. 116
. 116
. 117
. 117
. 117
. 118
. 119
. 119
. 120
. 122

57

2008 Ridgeline ０７／０４／２７　１３：４８：１５　３１ＳＪＣ６２０　００６３　

Control Locations

INSTRUMENT PANEL INDICATORS GAUGES

(P.70)

(P.59)

REAR VIEW MIRROR WITH COMPASS

(P.172)

＊

AUDIO SYSTEM (P.135)

PARKING BRAKE RELEASE HANDLE (P.111)

MIRROR CONTROLS (P.113)

POWER DOOR LOCK MASTER SWITCH (P.83)

POWER WINDOW SWITCHES (P.107)

HOOD RELEASE HANDLE (P.183)

FUEL FILL DOOR RELEASE HANDLE

AUXILIARY INPUT JACK

(P.165)

＊

HEATING/COOLING (P.124) CONTROLS CLIMATE CONTROL SYSTEM

(P.130)

GLOVE BOX (P.117)

(P.181)

PARKING BRAKE PEDAL

(P.111)

CENTER CONSOLE (P.115)

ACCESSORY POWER SOCKETS (P.118)

Vehicle with navigation system is shown.

＊

: If equipped

58

2008 Ridgeline ０７／０４／２７　１３：４８：２３　３１ＳＪＣ６２０　００６４　

U.S. models

VSA ACTIVATION INDICATOR

(P.67)

VTM-4 INDICATOR

(P.66)

HIGH BEAM INDICATOR

(P.65)

A/T TEMPERATURE INDICATOR

(P.66)

LIGHTS ON INDICATOR

(P.66)

TPMS INDICATOR

(P.68)

IN-BED TRUNK OPEN INDICATOR

(P.69)

(P.62)

CHARGING SYSTEM INDICATOR PARKING BRAKE AND BRAKE SYSTEM INDICATOR (P.63) LOW OIL PRESSURE INDICATOR MALFUNCTION INDICATOR LAMP

(P.291)

(P.62)

BED LIGHTS ON INDICATOR (P.69)

BACK WINDOW OPEN INDICATOR

(P.69)

DOOR AND TAILGATE MONITOR (P.64) TIRE PRESSURE MONITOR (P.68)

Instrument Panel

VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR (P.67) LOW TIRE PRESSURE INDICATOR (P.68)

MAINTENANCE MINDER INDICATOR

(P.67)

SIDE AIRBAG OFF (P.62) INDICATOR

IMMOBILIZER SYSTEM INDICATOR

(P.63)

WASHER LEVEL INDICATOR (P.65)

SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P.62)

SEAT BELT REMINDER INDICATOR (P.61)

LOW FUEL INDICATOR (P.65)

CRUISE CONTROL INDICATOR (P.65)

ANTI-LOCK BRAKE SYSTEM (ABS) INDICATOR

(P.63)

59

2008 Ridgeline ０７／０４／２７　１３：４８：３２　３１ＳＪＣ６２０　００６５　

Instrument Panel

Canadian models

VSA ACTIVATION INDICATOR

(P.67)

VTM-4 INDICATOR

(P.66)

(P.66)

(P.65)

(P.65)

HIGH BEAM INDICATOR A/T TEMPERATURE INDICATOR DAY TIME RUNNING LIGHTS INDICATOR LIGHTS ON INDICATOR TPMS INDICATOR (P.68) IN-BED TRUNK OPEN INDICATOR (P.69)

(P.66)

(P.62)

CHARGING SYSTEM INDICATOR PARKING BRAKE AND BRAKE SYSTEM INDICATOR (P.63) LOW OIL PRESSURE INDICATOR MALFUNCTION INDICATOR LAMP BED LIGHTS ON INDICATOR (P.69)

(P.291)

(P.62)

60

VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR (P.67)

LOW TIRE PRESSURE INDICATOR

(P.68)

DOOR AND TAILGATE MONITOR (P.64) TIRE PRESSURE MONITOR (P.68)

BACK WINDOW OPEN INDICATOR

(P.69)

MAINTENANCE MINDER INDICATOR

(P.67)

SIDE AIRBAG OFF INDICATOR (P.62)

IMMOBILIZER SYSTEM INDICATOR

(P.63)

WASHER LEVEL INDICATOR

(P.65)

SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P.62)

SEAT BELT REMINDER INDICATOR (P.61)

LOW FUEL INDICATOR (P.65)

CRUISE CONTROL INDICATOR (P.65)

ANTI-LOCK BRAKE SYSTEM (ABS) INDICATOR

(P.63)

2008 Ridgeline ０７／０４／２７　１３：４８：３７　３１ＳＪＣ６２０　００６６　

The instrument panel has many indicators to give you important information about your vehicle.

Seat Belt Reminder Indicator

This indicator comes on when you turn the ignition switch to the ON (II) position. It reminds you and your passengers to fasten your seat belts. A beeper also sounds if you have not fastened your seat belt.

If you turn the ignition switch to the ON (II) position before fastening your seat belts, the beeper sounds, and the indicator flashes. If you do not fasten your seat belts before the beeper stops, the indicator stops flashing but remains on.

Instrument Panel Indicators

If your front passenger does not fasten their seat belt, the indicator comes on about 6 seconds after the ignition switch is turned to the ON (II) position.

If either of you do not fasten your seat belt while driving, the beeper will sound and the indicator will flash again at regular intervals. For more information, see page

.18

61

2008 Ridgeline ０７／０４／２７　１３：４８：４７　３１ＳＪＣ６２０　００６７　

Supplemental Restraint System Indicator

This indicator comes on for several seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates a potential problem with your front airbags. This indicator will also alert you to a potential problem with your side airbags, passenger’s side airbag automatic cutoff system, side curtain airbags, rollover sensor, automatic seat belt tensioners, driver’s seat position sensor, or the front passenger’s weight sensors. 28
For more information, see page

Instrument Panel Indicators

Malfunction Indicator Lamp 291

See page

Low Oil Pressure Indicator

The engine can be severely damaged if this indicator flashes or stays on when the engine is running. For 290
more information, see page

Charging System Indicator

If this indicator comes on when the engine is running, the battery is not being charged. For more information, see page

290

62

U.S.

Canada

Side Airbag Off Indicator

This indicator comes on when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. For more information, see page

29

2008 Ridgeline ０７／０４／２７　１３：４８：５５　３１ＳＪＣ６２０　００６８　

Instrument Panel Indicators

U.S.

Canada

Parking Brake and Brake System Indicator

This indicator has two functions:

1.

2.

It comes on when you turn the ignition switch to the ON (II) position. It is a reminder to check the parking brake. A beeper sounds if you drive with the parking brake not fully released. Driving with the parking brake not fully released can damage the brakes and tires.

If it stays on after you have fully released the parking brake while the engine is running, or if it comes on while driving, there could be a problem with the brake system. For more information, see page

292

Anti-lock Brake System (ABS) Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position. If it comes on at any other time, there is a problem with the ABS. If this happens, have your vehicle checked at a dealer. With the indicator on, your vehicle still has normal braking ability but no anti- lock brakes. For more information, see page

213

Immobilizer System Indicator

This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. It will go off if you have inserted a properly-coded ignition key. If it is not a properly-coded key, the indicator will blink and the engine will not start (see page

81

).

This indicator also blinks several times when you turn the ignition switch from the ON (II) position to the ACCESSORY (I) or LOCK (0) position.

63

2008 Ridgeline ０７／０４／２７　１３：４９：０４　３１ＳＪＣ６２０　００６９　

Instrument Panel Indicators

Door and Tailgate Monitor

This monitor includes two functions; the door open indicator and the tailgate open indicator. This monitor works with the ignition switch in any position.

The specific door indicator comes on in this monitor if any door is not closed tightly.

The tailgate indicator comes on when the tailgate is swung open or if it is not closed completely after you swing it closed.

Turn Signal and Hazard Warning Indicators

The left or right turn signal indicator blinks when you signal a lane change or turn. If an indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see pages ). and Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.

258

259

When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.

64

If the tailgate is swung open or is not closed tightly, you will hear six beeps and see the indicator blinking when you turn the ignition switch to the ON (II) position. The beeper also sounds and the indicator blinks when you move the shift lever out of the Park or neutral position.

The tailgate open indicator does not monitor the tailgate when it is dropped open.

If the driver does not fasten the seat belt and the tailgate is swung open, the seat belt reminder alarm will sound at first, then the tailgate open reminder beeper will sound. For more information on the tailgate, see page

95

2008 Ridgeline ０７／０４／２７　１３：４９：１４　３１ＳＪＣ６２０　００７０　

‘‘Daytime Running Lights’’ Indicator

Canadianmodelsonly This indicator comes on when you turn the ignition switch to the ON (II) position with the headlight switch off and the parking brake set. It should go off when you turn on the headlights or release the parking brake. If it comes on at any other time, it means there is a problem with the DRL. There may also be a problem with the high beam headlights.

Cruise Control Indicator

This indicator comes on when you set the cruise control. See page 169
cruise control.

for information on operating the

Instrument Panel Indicators

High Beam Indicator

Low Fuel Indicator

This indicator comes on with the high beam headlights. For more information, see page

76

On Canadian models, this indicator comes on with reduced brightness when the daytime running lights (DRL) are on (see page

78

).

Washer Level Indicator

This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator (see page

252

).

LOW FUEL INDICATOR

This indicator is located in the fuel gauge. It comes on as a reminder that you must refuel soon.

When the indicator comes on, there is about 3.30 U.S. gal (12.5 ) of fuel remaining in the tank before the needle reaches E. There is a small reserve of fuel remaining in the tank when the needle does reach E.

65

2008 Ridgeline ０７／０４／２７　１３：４９：２２　３１ＳＪＣ６２０　００７１　

Instrument Panel Indicators

Lights On Indicator

This indicator reminds you that the exterior lights are on. It comes on when you turn the headlight control dial to either the

or

position.

If you turn the ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the headlight control dial, this indicator remains on. A reminder chime will also sound when you open the driver’s door.

66

A/T Temperature Indicator

This indicator monitors the temperature of the automatic transmission fluid. It should come on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on while driving, it means the transmission fluid temperature is too high. Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.

Continuing to drive with the A/T temperature indicator on may cause serious damage to the transmission.

VTM-4 Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, there is a problem in the 4WD system. Take the vehicle to your dealer to have it checked.

If the indicator blinks while driving, the VTM-4 fluid temperature is too high. Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.

Continuing to drive with the VTM-4
indicator blinking may cause serious damage to the system.

2008 Ridgeline ０７／０４／２７　１３：４９：３４　３１ＳＪＣ６２０　００７２　

Instrument Panel Indicators

Vehicle Stability Assist (VSA) System Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If it comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the VSA system. Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. See page for more information on the 215
VSA system.

VSA Activation Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. For more information, see page

215

This indicator has three functions:

1.

2.

3.

It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.

It flashes when VSA is active (see page

215

).

It comes on along with the VSA system indicator if there is a problem with the VSA system.

Maintenance Minder Indicator

This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. It reminds you that it is time to take your vehicle in for scheduled maintenance. The maintenance main items and sub items will be displayed in the information display. See page 239
maintenance minder.

for more information on the

This indicator goes off when your dealer resets it after completing the required maintenance service.

67

2008 Ridgeline ０７／０４／２７　１３：４９：４２　３１ＳＪＣ６２０　００７３　

Instrument Panel Indicators

Low Tire Pressure Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.

Tire Pressure Monitor

The appropriate tire indicator will come on along with the low tire pressure indicator if a tire is significantly underinflated or has Low suddenly lost pressure. See Tire Pressure Indicator do if this indicator comes on.

for what to

If this happens, pull to the side of the road when it is safe, check which tire has lost the pressure on the tire pressure monitor, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service (see page 208

for more information.

). Refer to page

276

298

68

Tire Pressure Monitoring System (TPMS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the TPMS. With this indicator on, the low tire pressure indicator and the tire pressure monitor will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked.

2008 Ridgeline ０７／０４／２７　１３：４９：５２　３１ＳＪＣ６２０　００７４　

In-Bed Trunk Open Indicator

This indicator reminds you that the In-Bed Trunk is open. If you do not close it, the indicator stays on for about 3 minutes. See page for more information.

96

Bed Lights On Indicator

This indicator reminds you that the bed lights are on. With the shift lever in the Park position, they come on when you push the light switch on the dashboard, swing open the tailgate, or open the In-Bed Trunk.

If you turn the ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the bed lights, this indicator will remain on, and then go off after 20 minutes. See page

for more information.

122

Instrument Panel Indicators

Back Window Open Indicator

This indicator reminds you that the back window is not completely closed when you turn the ignition switch from the ON (II) position to the ACCESSORY (I) or LOCK (0) position. With the ignition switch in the ACCESSORY (I) position, it goes off after about 30 seconds. With the ignition switch in the LOCK (0) position, it goes off after about 3
minutes.

If you remove the ignition key, turn off the lights, and open the driver’s door without closing the back window, you will hear five beeps and see the indicator blink. If you do not close the back window before the beeper stops, the indicator stops blinking but remains on. It will go off after about 3 minutes. See page 108

for more information.

69

2008 Ridgeline ０７／０４／２７　１３：４９：５８　３１ＳＪＣ６２０　００７５　

Gauges

TACHOMETER

SPEEDOMETER

TEMPERATURE GAUGE

FUEL GAUGE

ODOMETER/ TIGHTEN FUEL CAP MESSAGE

SELECT BUTTON

OUTSIDE TEMPERATURE INDICATOR

INFORMATION DISPLAY

TRIP METER

RESET BUTTON

U.S. model is shown.

70

To switch the information display between the odometer, trip meter and outside temperature (if equipped), and engine oil life and maintenance service items, press the SELECT button repeatedly.

Odometer This shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

2008 Ridgeline ０７／０４／２７　１３：５０：０４　３１ＳＪＣ６２０　００７６　

Gauges

When you turn the ignition switch to the ON (II) position, the last selection is displayed.

To reset a trip meter, display it, and then press and hold the RESET button until the number resets to ‘‘0.0’’. Both trip meters will reset if the vehicle’s battery goes dead or is disconnected. And both continue to track mileage, even when only one is displayed.

Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it.

SELECT BUTTON

RESET BUTTON

There are two trip meters: TRIP A and TRIP B. Switch between these displays by pressing the SELECT button repeatedly. Each trip meter works independently, so you can keep track of two different distances.

71

2008 Ridgeline ０７／０４／２７　１３：５０：１３　３１ＳＪＣ６２０　００７７　

Gauges

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise to about the middle of the gauge. In severe driving conditions, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. For instructions and precautions on checking the engine’s cooling system, see page

288

Outside Temperature Indicator Ifequipped This indicator displays the outside temperature in Fahrenheit (U.S. models) or Centigrade (Canadian models).

The temperature sensor is in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your speed is under 19 mph (30 km/h).

cooler.

NOTE: The temperature must be stabilized before doing this procedure.

To adjust the outside temperature indicator, make sure the outside temperature indicator is shown in the display, then press and hold the RESET button for 10 seconds (the TRIP A or B is also reset). The following sequence will appear for 1
second each: 0, 1, 2, 3, 4, 5, 4, − − − − − −

− − 1, 0 (U.S.) or 0, 1, 2, 3, 1, 0 (Canada).

2, 2,

3, 3,

5,

The sensor delays the indicator update until it reaches the correct outside temperature. This may take several minutes.

When it reaches the desired value, release the RESET button. You should see the new outside temperature displayed.

If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or

5°F in U.S. models (

±

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

72

2008 Ridgeline ０７／０４／２７　１３：５０：１８　３１ＳＪＣ６２０　００７８　

Gauges

Tighten Fuel Cap Message If your fuel fill cap is loose or missing, a ‘‘TIGHTEN FUEL CAP’’ message appears on the information display after you start the engine. Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen it, then retighten it until it clicks at least once. When you restart the engine, the message appears again. The message goes off after several days of normal driving once you tighten or replace the fuel fill cap. To scroll to another display, press the SELECT button.

If the system still detects a leak in your vehicle’s evaporative emissions system, the malfunction indicator lamp (MIL) comes on. If the fuel fill cap was not already tightened, turn the engine off, and check or retighten the fuel fill cap until it clicks at least once. The MIL should go off after several days of normal driving once the cap is tightened or replaced. If the MIL does not go off, have your vehicle inspected by a dealer. For more information, see page

291

Maintenance Minder Display The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.

239

for

73

2008 Ridgeline ０７／０４／２７　１３：５０：２６　３１ＳＪＣ６２０　００７９　

Controls Near the Steering Wheel

MOONROOF SWITCH ＊ (P.110)

INSTRUMENT PANEL BRIGHTNESS

(P.78)

SHIFT LEVER (P.201)

VTM-4 LOCK

(P.206)

MULTI-CONTROL LEVER (WINDSHIELD WIPERS/ WASHERS/TURN SIGNALS/ HEADLIGHT HIGH BEAMS) (P.75) BED LIGHT SWITCH (P.122)

HEADLIGHT CONTROL DIAL

(P.76)

VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P.216)

CRUISE BUTTON (P.169)

SELECT BUTTON (P.70) RESET BUTTON (P.70) PASSENGER AIRBAG OFF INDICATOR (P.29) HAZARD WARNING BUTTON (P.79)

REMOTE AUDIO CONTROLS ＊

(P.165)

STEERING WHEEL ADJUSTMENT

(P.79)

CRUISE CONTROLS (P.169)

HORN ＊

Vehicle with navigation system is shown.

To use the horn, press the pad around the ‘‘H’’ logo. If equipped.

1: ＊ 2: ＊ 74

INTERIOR LIGHT CONTROL SWITCH (P.120)

SEAT HEATERS ＊ (P.105)

2008 Ridgeline ０７／０４／２７　１３：５０：３６　３１ＳＪＣ６２０　００８０　

The multi-control lever has many functions, including windshield wipers and washers, turn signals, headlight high beams, and headlight high beam flashing.

To select a position, turn the rotary switch, push the button on the end of the lever, or push the lever up, down, forward, or backward.

OFF:

The wipers are not activated.

INT:

The length of the wiper interval is varied automatically according to the vehicle’s speed.

Vary the delay by turning the INT TIME ring. If you turn it to the shortest delay, the wipers change to low speed when the vehicle speed exceeds 12 mph (20 km/h).

Multi-Control Lever

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

MIST:

The wipers run at high speed until you release the lever.

Windshield Washer:

Push the button on the end of the multi-control lever. The washers spray until you release the button. The wipers run at low speed, then complete one more sweep after you release the button.

CONTINUED

75

1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

OFF INT: Intermittent INT TIME ring LO: Low speed HI: High speed MIST Windshield washers Turn signal High beams Flash high beams

2008 Ridgeline ０７／０４／２７　１３：５０：４３　３１ＳＪＣ６２０　００８１　

Multi-Control Lever, Headlights

Headlight Control Dial

−

Turn Signal Push down on the multi-control lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to center when you release it or complete a turn.

−

High Beams To turn on the high beams, push the multi-control lever forward until you hear a click. The blue high beam indicator will come on (see page to return to the low beams.

). Pull the lever back

65

To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

1. 2. 3.

OFF Parking and indicator lights Headlights

AutomaticHeatedWiperZone Your vehicle has heating wires at the bottom of the windshield to help heat the wiper blades and the windshield. If the outside temperature is near freezing, the heater turns on automatically when you turn the ignition switch to the ON (II) position. The heater turns off automatically when the outside temperature is above freezing.

This function helps to increase wiper performance when the wiper arms sit in the parked position in snowy or icy conditions.

76

2008 Ridgeline ０７／０４／２７　１３：５０：５１　３１ＳＪＣ６２０　００８２　

Automatic Lighting Off Feature The automatic lighting off feature turns off the headlights, all other exterior lights, and the instrument panel lights within 15 seconds of removing the key from the ignition switch and closing the driver’s door.

This feature activates if you leave the headlight control dial in the ‘‘ the key, then open and close the driver’s door.

’’ position, remove

’’ or ‘‘

−

Turning the dial to ’’ position turns on the

Headlights the ‘‘ parking lights, taillights, instrument panel lights, and license plate lights.

’’

Turning the dial to the ‘‘ position turns on the headlights. If you leave the lights on and remove the key from the ignition switch, you will hear a reminder chime when you open the driver’s door.

’’ or

’’ position, the lights on

When the dial is in the ‘‘ ‘‘ indicator comes on as a reminder. This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.

Headlights

If you remove the key from the ignition switch with the headlight control dial on, but do not open the door, the lights will turn off after 10
minutes.

The lights will turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights go off. With the driver’s door open, you will hear a lights-on reminder chime.

77

2008 Ridgeline ０７／０４／２７　１３：５１：００　３１ＳＪＣ６２０　００８３　

Headlights, Instrument Panel Brightness

Daytime Running Lights Canadianmodelsonly With the headlight control dial off, the high beam headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.

The headlights revert to normal operation when you turn them on with the headlight control dial.

78

Instrument Panel Brightness

If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door.

If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off in about 10 seconds.

The instrument panel brightness is dimmed when you turn the headlight control dial to the ‘‘ ‘‘ night. To cancel it, turn the instrument panel brightness control dial upward fully until you hear a click.

’’ position to reduce glare at

’’ or

INSTRUMENT PANEL BRIGHTNESS CONTROL DIAL

The dial on the instrument panel controls the brightness of the instrument panel lights and the console compartment light. Turn the dial to adjust the brightness.

The instrument panel will illuminate when you unlock and open the driver’s door. The brightness will increase when you insert the key in the ignition switch.

2008 Ridgeline ０７／０４／２７　１３：５１：０８　３１ＳＪＣ６２０　００８４　

Hazard Warning Button, Steering Wheel Adjustment

Hazard Warning Button

Steering Wheel Adjustment Make any steering wheel adjustment before you start driving.

Push the button to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

1.

2.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

3.

Push the lever up to lock the steering wheel in position.

Push the lever on the left side of the steering column all the way down.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up and down.

Move the steering wheel so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

79

2008 Ridgeline ０７／０４／２７　１３：５１：１５　３１ＳＪＣ６２０　００８５　

Keys

KEY NUMBER TAG

MASTER KEY WITH REMOTE TRANSMITTER

VALET KEY (LIGHT GRAY)

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.

These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.

The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the glove box locked when you leave your vehicle and the valet key at a parking facility.

Protect the keys from direct sunlight, high temperature, and high humidity.

Do not drop the keys or set heavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

The valet key does not contain a battery. Do not try to take it apart.

You can also keep the In-Bed Trunk locked by using the main switch in the glove box (see page

98

).

80

2008 Ridgeline ０７／０４／２７　１３：５１：２３　３１ＳＪＣ６２０　００８６　

Immobilizer System

The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.

When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on for a few seconds, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.

The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.

If the system repeatedly does not recognize the coding of your key, contact your dealer.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

If you have lost your key and cannot start the engine, contact your dealer.

Always take the ignition key with you whenever you leave the vehicle alone.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

81

2008 Ridgeline ０７／０４／２７　１３：５１：３０　３１ＳＪＣ６２０　００８７　

Ignition Switch

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly.

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

−

You can

ACCESSORY (I) operate the audio system and the accessory power sockets in this position.

−

This is the normal key

ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).

82

−

Use this position

START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

The shift lever must be in Park before you can remove the key from the ignition switch.

2008 Ridgeline ０７／０４／２７　１３：５１：３７　３１ＳＪＣ６２０　００８８　

Power Door Locks

LOCK TAB

The lock tab on each door locks and unlocks that door. Pulling up on the driver’s door lock tab only unlocks the driver’s door. To unlock the driver’s door and the In-Bed Trunk from the outside, turn the key and release it. If you turn it again, all the doors unlock.

You can open or close the side windows by using the key in the driver’s door (see page

109

).

MASTER DOOR LOCK SWITCH

To lock all doors and the In-Bed Trunk, push the front of the master door lock switch on either front door, press the lock tab down on the driver’s door, or use the key on the outside lock on the driver’s door.

Pushing the rear of either master door lock switch will unlock all of the doors and the In-Bed Trunk.

Door Locks