Download PDF Manual


The oil container may also display the API Certification seal. Make sure it says "For Gasoline Engines."


The SAE numbers tell you the oil's viscosity or weight. Select the oil for your vehicle according to this chart.


API CERTIFICATION SEAL


Ambient Temperature


An oil with a viscosity of 5W-30 is preferred for improved fuel economy and year-round protection in your Honda. You may use a 10W-30 oil if the temperature in your area never goes below 20°F( — 7°C).


Maintenance


Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for conventional motor oil; energy conserving, a service classification of SJ, and the proper weight as shown on the chart. When using synthetic oil, you must follow the oil and filter change intervals given in the maintenance schedule.


Additives Your Honda does not need any oil additives. Purchasing additives for the engine or transmission will not increase your vehicle's performance or longevity. It only increases the cost of operating your vehicle.


Main MenuTable of Contentsst Changing the Oil and Filter Always change the oil and filter according to the time and distance (miles/kilometers) recommenda- tions in the maintenance schedule. The oil and filter collect contami- nants that can damage your engine if they are not removed regularly.


Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service station- type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled mechanic.


1. Run the engine until it reaches normal operating temperature, then shut it off.


OIL DRAIN BOLT


WASHER 2. Open the hood and remove the


engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.


Engine Oil


Type SH


OIL FILTER


3. Remove the oil filter and let the


remaining oil drain. A special wrench (available from your Honda dealer) is required to remove the filter.


CONTINUED


Maintenance


Main MenuTable of Contentsst Engine Oil


Except Type SH


OIL FILTER


4. Install a new oil filter according to


instructions that come with it.


Maintenance


9. Turn off the engine, let it sit for


several minutes, then check the oil level. If necessary, add oil to bring the level to the upper mark on the dipstick.


NOTICE


Improper disposal of engine oil can be harmful to the environment. If yon change your own oil, please dispose of the used oil properly. Put it in a sealed container and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground.


5. Put a new washer on the drain bolt,


then reinstall the drain bolt. Tighten it to: 33 Ibf.ft (44 N.m , 4.5 kgf.m)


6. Refill the engine with the recom-


mended oil. Engine oil change capacity (including filter): 5.1 US qt(4.8 l ,4.2 Imp qt)


7. Replace the engine oil fill cap.


Start the engine. The oil pressure indicator light should go out within five seconds. If it does not, turn off the engine and reinspect your work.


8. Let the engine run for several


minutes and check the drain bolt and oil filter for leaks.


Main MenuTable of Contentsst Cooling System


Always use Genuine Honda antifreeze/coolant. If it is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. However, continued use of any non- Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/ coolant as soon as possible.


If the reserve tank is completely empty, you should also check the coolant level in the radiator.


Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.


Always let the engine and radiator cool down before removing the radiator cap.


Adding Engine Coolant


RESERVE TANK If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks. This coolant should always be a mixture of 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water.


CONTINUED


Maintenance


Main MenuTable of Contentsst 3. Remove the radiator cap by pushing down and turning counterclockwise.


4. The coolant level should be up to


the base of the filler neck. Add coolant if it is low.


5. Put the radiator cap back on.


Tighten it fully.


RESERVE TANK


6. Pour coolant into the reserve tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank.


Cooling System


RADIATOR CAP


1. Make sure the engine and


radiator are cool.


2. Turn the radiator cap counter-


clockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system.


Maintenance


Main MenuTable of Contentsst Do not add any rust inhibitors or other additives to your vehicle's cooling system. They may not be compatible with the coolant or engine components.


Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and distance recommendations in the maintenance schedule. Only use Genuine Honda antifreeze/coolant.


Draining the coolant requires access to the underside of the vehicle. Unless you have the tools and knowledge, you should have this maintenance done by a skilled mechanic.


Cooling System


DRAIN PLUG


1. Slide the heater temperature


control lever to maximum heat. Open the hood. Make sure the engine and radiator are cool to the touch.


2. Remove the radiator cap.


Type SH


3. Loosen the drain plug on the bottom of the radiator. The coolant will come out through the hole in the splash cover.


CONTINUED


Maintenance


Main MenuTable of Contentsst Cooling System


DRAIN BOLT


RESERVE TANK


RESERVE TANK CAP


Except Type SH


DRAIN PLUG


HOLDER


Except Type SH only Remove the drain bolt and washer from the engine block.


4. Remove the reserve tank from its


holder by pulling it straight up. Drain the coolant, then put the tank back in its holder.


5. When the coolant stops draining,


tighten the drain plug in the bottom of the radiator.


Maintenance


Except Type SH only Apply non-hardening sealant to the drain bolt threads, put a new washer on the drain bolt, and reinstall the bolt in the engine block. Tighten it securely. Tightening torque: 61 Ibf.ft (83 N.m , 8.5 kgf.m)


6. Mix the recommended antifreeze with an equal amount of purified or distilled water in a clean container. The cooling system capacity is:


With 5-speed manual transmission: (Except Type SH) 0.87 US gal (3.3 l , 0.73 Imp gal)


(TypeSH) 0.85 US gal (3.2 l ,0.70 Imp gal)


With automatic transmission: 0.85 US gal (3.2 l , 0.70 Imp gal)


Main MenuTable of Contentsst FILLER NECK


Cooling System


Fill up to here


7. Pour coolant into the radiator up


to the base of the filler neck.


BLEEDER BOLT


RESERVE TANK


8. Loosen the bleeder bolt on top of the engine. Tighten it again when coolant comes out in a steady stream with no bubbles.


10. Turn off the engine. Check the


level in the radiator, add coolant if needed. Install the radiator cap, and tighten it fully.


9. Refill the radiator to the base of the filler neck. Start the engine and let it run until it warms up (the radiator cooling fan comes on at least twice).


11. Fill the reserve tank to the MAX


mark. Install the reserve tank cap.


Maintenance


Main MenuTable of Contentsst The windshield washer reservoir is located behind the driver's side headlight. Check the reservoir's fluid level by removing the cap and looking at the float. It should be up to the top of the neck. If the float is at the bottom of the neck, the reservoir is nearly empty.


Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather.


NOTICE


Do not use engine antifreeze or a vinegar/water solution in the windshield washer reservoir.


Antifreeze can damage your vehicle's paint, while a vinegar/water solution can damage the windshield washer pump.


Use only commercially-available windshield washer fluid.


Windshield Washers


FLOAT


Check the level in the windshield washer reservoir at least monthly during normal usage. In bad weather, when you use the washers often, check the level every time you stop for fuel.


Maintenance


Main MenuTable of Contentsst Automatic Transmission


DIPSTICK


Check the fluid level with the engine at normal operating temperature.


1. Park the vehicle on level ground.


Shut off the engine.


2. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth.


Transmission Fluid


5. If the level is below the lower


mark, add fluid into the filler hole to bring it to the upper mark. Always use Honda Premium Formula Automatic Transmission Fluid (ATF). If it is not available, you may use a DEXRON® III automatic transmission fluid as a temporary replacement. However, continued use can affect shift quality. Have the transmission drained and refilled with Honda ATF as soon as it is convenient.


DIPSTICK


UPPER MARK LOWER MARK


3. Insert the dipstick all the way into


the transmission securely as shown in the illustration.


6. Insert the dipstick all the way back


into the transmission securely as shown in the illustration.


4. Remove the dipstick and check


the fluid level. It should be between the upper and lower marks.


The transmission should be drained and refilled with new fluid according to the time and distance recommen- dations in the maintenance schedule.


Maintenance


Main MenuTable of Contentsst Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Genuine Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole. Reinstall the filler bolt and tighten it securely.


If Honda MTF is not available, you may use an API service SG, SH or SJ grade motor oil with a viscosity of SAE 10W-30 or 10W-40 as a temporary replacement. An SG grade is preferred, but an SH or SJ grade may be used if SG is not available. However, motor oil does not contain the proper additives and continued use can cause stiffer shifting. Replace as soon as convenient.


The transmission should be drained and refilled with new fluid according to the time and distance recommen- dations in the maintenance schedule.


Transmission Fluid


5-speed Manual Transmission


FILLER BOLT


Correct level


Maintenance


Main MenuTable of Contentsst Check the fluid level in the reser- voirs monthly. There are up to two reservoirs, depending on model. They are:


Brake fluid reservoir (all models) Clutch fluid reservoir (manual transmission only)


The brake fluid in the brake system should be replaced according to the time and distance recommendations in the maintenance schedule.


Always use Genuine Honda DOT 3
brake fluid. If it is not available, you should use only DOT 3 or DOT 4
fluid, from a sealed container, as a temporary replacement. However, the use of any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda DOT 3 brake fluid as soon as possible.


Brake fluid marked DOT 5 is not compatible with your vehicle's braking system and can cause extensive damage.


Brake and Clutch Fluid


Brake System


MAX


MIN


The fluid level should be between the MIN and MAX marks on the side of the reservoir. If the level is at or below the MIN mark, your brake system needs attention. Have the brake system inspected for leaks or worn brake pads.


Maintenance


Main MenuTable of Contentsst Brake and Clutch Fluid, Power Steering


Clutch System


Power Steering


UPPER LEVEL


LOWER LEVEL


Check the level when the engine is cold. Look at the side of the reservoir. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If it is below the LOWER LEVEL, add power steering fluid to the UPPER LEVEL.


MAX


MIN


The fluid should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system.


Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.


Maintenance


Always use Genuine Honda Power Steering Fluid. If it is not available, you may use another power steering fluid as an emergency replacement. However, continued use can cause increased wear and poor steering in cold weather. Have the power steering system flushed and refilled with Honda PSF as soon as possible.


A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently and have the system inspected as soon as possible.


NOTICE


Turning the steering wheel to full left or right lock and holding it there can damage the power steering pump.


Main MenuTable of Contentsst The air cleaner element should be cleaned or replaced according to the time and distance recommendations in the maintenance schedule.


Cleaning (Severe Conditions) Clean the air cleaner element by blowing compressed air through it in the opposite direction to normal air flow. If you do not have access to compressed air (such as a service station), ask your Honda dealer to do this service.


Follow the replacement procedure for removal and reinstallation.


Air Cleaner Element


Replacement


CLAMPS


The air cleaner element is inside the air cleaner housing on the passenger's side of the engine compartment. To replace it:


1. Unsnap the four hold-down clamps


and remove the air cleaner housing cover.


AIR CLEANER ELEMENT


2. Remove the old air cleaner


element.


Clean the inside of the air cleaner housing with a damp rag.


3. Place the new air cleaner element


in the air cleaner housing.


4. Reinstall the air cleaner housing cover, snap the four hold-down clamps back into place.


Maintenance


Main MenuTable of Contentsst Spark Plugs


The spark plugs in your vehicle are a special platinum-tipped design for longer life. They only need to be replaced every 7 years or 105,000
miles (168,000 km), whichever comes first.


Replacement


NUTS


NUTS


SPARK PLUG CAP


1. Remove the four nuts, then remove the plug wire cover.


3. Remove the spark plug cap by


pulling it straight out.


2. Clean up any dirt and oil around


the spark plug caps.


4. Remove the spark plug with


a five-eighths inch (16 mm) spark plug socket.


Maintenance


Main MenuTable of Contentsst 5. Put the new spark plug into the


socket; then screw it into the hole. Screw it in by hand so you do not crossthread it.


6. Torque the spark plug. (If you do not have a torque wrench, tighten the spark plug two-thirds of a turn after it contacts the cylinder head.) Tightening torque: 13 lbf.ft (18 N.m, 1.8 kgf.m)


Spark Plugs


NOTICE


Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head.


7. Install the spark plug cap.


8. Repeat this procedure for the


other three spark plugs.


Reinstall the plug wire cover and tighten the four nuts.


Maintenance


Main MenuTable of Contentsst Spark Plugs, Battery


Specifications:


NGK: DENSO:


Spark Plug Gap:


PZFR6F-11
PKJ20CR-L11


0.043 in


(1.1mm


Battery Check the condition of your vehicle's battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals.


TEST INDICATOR WINDOW


Check the battery condition by looking at the test indicator window on the battery. The label on the battery explains the test indicator's colors.


Maintenance


Main MenuTable of Contentsst Battery


The battery gives off explosive hydrogen gas during normal operation.


A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.


Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.


If the terminals are severely cor- roded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals. Always disconnect the negative ( —) cable first and recon- nect it last. Clean the battery termi- nals with a terminal cleaning tool or wire brush. Reconnect and tighten the cables, then coat the terminals with grease.


If you need to connect the battery to a charger, disconnect both cables to prevent damage to the vehicle's electrical system.


CONTINUED


Maintenance


Check the battery terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent future corrosion.


Main MenuTable of Contentsst Battery


If your vehicle's battery is discon- nected or goes dead, the audio system will disable itself. The next time you turn on the radio you will see "Code" in the frequency display. Use the Preset buttons to enter the five-digit code (see page 117).


NOTICE


Charging the battery with the cables connected can seriously damage your vehicle's electronic controls. Detach the battery cables before connecting the battery to a charger.


Maintenance


Main MenuTable of Contentsst Check the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used.


WIPER ARMS


Wiper Blades


LOCK TAB


To replace the blade:


1. Raise the wiper arm off the


windshield. Raise the driver's side first, then the passenger's side.


2. Disconnect the blade assembly


from the wiper arm by pushing in the lock tab. Hold it in while you push the blade assembly toward the base of the arm.


CONTINUED


Maintenance


Main MenuTable of Contentsst 5. Slide the new wiper blade into the


holder until the tabs lock.


6. Slide the wiper blade assembly


onto the wiper arm. Make sure it locks in place.


7. Lower the wiper arm down against


the windshield. Lower the passenger's side first, then the driver's side.


Wiper Blades


BLADE


BLADE


3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder.


REINFORCEMENT


4. Examine the new wiper blades. If they have no plastic or metal rein- forcement along the back edge, remove the metal reinforcement strips from the old wiper blade and install them in the slots along the edge of the new blade.


Maintenance


Main MenuTable of Contentsst Air Conditioning System


Your vehicle's air conditioning is a sealed system. Any major mainte- nance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently.


Periodically check the engine's radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface. These block the air flow and reduce cooling efficiency. Use a light spray from a hose or a soft brush to remove them.


If the air conditioning does not get as cold as before, have your dealer check the system. Recharge the system with Refrigerant HFC-134a (R-134a). (See Specifications on page 255.)


AIR CONDITIONING CONDENSER


NOTICE


The condenser and radiator fins bend easily. Only use a low-pressure spray or soft-bristle brush to clean them.


Run the air conditioning at least once a week during the cold weather months. Run it for at least ten minutes while you are driving at a steady speed with the engine at normal operating temperature. This circulates the lubricating oil con- tained in the refrigerant.


NOTICE


Whenever you have the air conditioning system serviced, make sure the service facility uses a refrigerant recycling system. This system captures the refrigerant for reuse. Releasing refrigerant into the atmosphere can damage the environment.


Maintenance


Main MenuTable of Contentsst The belts should have the following "play" or deflection. Alternator belt:


0.37-0.49 in (9.5-12.5 mm)


Power steering belt:


0.53-0.65 in (13.5-16.5 mm)


If you see signs of wear or looseness, have your dealer adjust or replace the belts.


Timing Belt The timing belt and balancer belt should normally be replaced at the intervals shown in the maintenance schedule.


Replace these belts at 60,000 miles (U.S.) or 100,000 km (Canada) if you regularly drive your vehicle in one or more of these conditions:


In very high temperatures (over110°F,43°C). In very low temperatures (under — 20°F, — 29°C).


Drive Belts, Timing Belt


Drive Belts


POWER STEERING BELT


ALTERNATOR BELT


Check the condition of the two drive belts. Examine the edges of each belt for cracks or fraying. Check the tension of each belt by pushing on it with your thumb midway between the pulleys.


Maintenance


Main MenuTable of Contentsst To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how and when to check air pressure, how to inspect your tires for damage and wear, and what to do when your tires need to be replaced.


Inflation Keeping the tires properly inflated provides the best combination of handling, tread life and riding comfort. Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated. Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly.


Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.


We recommend that you visually check your tires every day. If you think a tire might be low, check it immediately with a tire gauge.


Follow all instructions in this owner's manual regarding tire inflation and maintenance.


Use a gauge to measure the air pressure at least once a month. Even tires that are in good condition may lose one to two psi (10 to 20 kPa, 0.1
to 0.2 kgf/cm2) per month. Remember to check the spare tire at the same time you check all the other tires.


Tires


Check the pressure in the tires when they are cold. This means the vehicle has been parked for at least three hours. If you have to drive the vehicle before checking the tire pressure, the tires can still be considered "cold" if you drive less than 1 mile (1.6km).


If you check the pressure when the tires are hot (the vehicle has been driven several miles), you will see readings 4 to 6 psi (30 to 40 kPa, 0.3
to 0.4 kgf/cm2) higher than the cold reading. This is normal. Do not let air out to match the specified cold pressure. The tire will be underinflated.


You should get your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges.


CONTINUED


Maintenance


Main MenuTable of Contentsst Tubeless tires have some ability to self-seal if they are punctured. However, because leakage is often very slow, you should look closely for punctures if a tire starts losing pressure.


Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear.


You should look for:


Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions.


Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord.


Excessive tread wear.


Tires


Recommended Tire Pressures for Normal Driving The following chart shows the recommended cold tire pressures for most normal driving conditions and speeds. Tire pressures for high speed driving are shown on page 257.


The compact spare tire pressure is: 60 psi (420 kPa , 4.2 kgf/cm2)


These pressures are also given on the tire information label on the driver's doorjamb.


Maintenance


Main MenuTable of Contentsst INDICATOR LOCATION MARKS


TREAD WEAR INDICATORS


Your vehicle's tires have wear indica- tors molded into the tread. When the tread wears down to that point, you will see a 1/2 inch (12.7 mm) wide band running across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. A tire that is this worn gives very little traction on wet roads. You should replace the tire if you can see the tread wear indicator in three or more places around the tire.


Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment.


The tires were properly balanced by the factory. They may need to be rebalanced at some time before they are worn out. Have your dealer check the tires if you feel a consis- tent vibration while driving. A tire should always be rebalanced if it is removed from the wheel for repair.


Make sure the installer balances the wheels when you have new tires installed. This increases riding comfort and tire life. Your vehicle's original tires were dynamic or "spin" balanced at the factory. For best results, have the installer perform a dynamic balance.


Tires


NOTICE


Improper wheel weights can damage your vehicle's aluminum wheels. Use only Genuine Honda wheel weights for balancing.


Maintenance


Main MenuTable of Contentsst Tires


Tire Rotation


Front


Front


(For Non-directional Tires and Wheels)


(For Directional Tires and Wheels)


To help increase tire life and distribute wear more evenly, you should have the tires rotated every 7,500 miles (12,000 km). Move the tires to the positions shown in the chart each time they are rotated.


Maintenance


When shopping for replacement tires, you may find that some tires are "directional." This means they are designed to rotate only in one direction. If you use directional tires, they should be rotated only front-to-back.


Replacing Tires and Wheels The tires that came with your vehicle were selected to match the performance capabilities of the vehicle while providing the best combination of handling, ride comfort, and long life. You should replace them with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire's sidewall). Mixing radial and bias-ply tires on your vehicle can reduce its braking ability, traction, and steering accuracy.


Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.


Always use the size and type of tires recommended in this owner's manual.


It is best to replace all four tires at the same time. If that is not possible or necessary, then replace the two front tires or the two rear tires as a pair. Replacing just one tire can seriously affect your vehicle's han- dling.


Main MenuTable of Contentsst Tires


The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the vehicle. Tire size and construction can affect wheel speed and may cause the system to work inconsistently.


Wheels and Tires Wheel:


16x61/2 JJ


Tire:


205/50R1687V


If you ever need to replace a wheel, make sure the wheel's specifications match those of the original wheel that came on your vehicle. Re- placement wheels are available at your Honda dealer.


See Tire Information on page 256 for additional information about tire and wheel size designations. See page 257 for information about DOT Tire Quality Grading.


Winter Driving Tires that are marked "M + S" or "All Season" on the sidewall have an all-weather tread design. They should be suitable for most winter driving conditions. Tires without these markings are designed for optimum traction in dry conditions. They may not provide adequate performance in winter driving. For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.


CONTINUED


Maintenance


Main MenuTable of Contentsst NOTICE


Chains of the wrong size or that are improperly installed can damage your vehicle's brake lines, suspension, body, and wheels. Stop driving if you hear the chains hitting any part of the vehicle.


Tires


Snow Tires If you mount snow tires on your Honda, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your vehicle's handling in all weather conditions. Keep in mind the traction provided by snow tires on dry roads may not be as high as your vehicle's original equipment tires. You should drive cautiously even when the roads are clear. Check with the tire dealer for maximum speed recommenda- tions.


Maintenance


Tire Chains Mount snow chains on your vehicle when warranted by driving condi- tions or required by local laws. Make sure the chains are the correct size for your tires. Install them only on the front tires. If metal chains are used, they must be SAE class "S". Cable type traction devices can also be used.


When installing chains, follow the manufacturer's instructions and mount them as tightly as you can. Drive slowly with chains installed. If you hear the chains contacting the body or chassis, stop and investigate. Make sure the chains are installed tightly, and that they are not contacting the brake lines or suspension. Remove the chains as soon as you begin driving on cleared roads.


Main MenuTable of Contentsst PARKING LIGHT


HEADLIGHT LOW BEAM


Lights


Check the operation of your vehicle's exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your vehicle's visibility and the ability to signal your intentions to other drivers.


HEADLIGHT HIGH BEAM


TURN SIGNAL


SIDE MARKER LIGHT


CONTINUED


Maintenance


Main MenuTable of Contentsst Lights


Check the following:


Headlights (low and high beam) Parking lights Taillights Brake lights High-mount brake light Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian models)


If you find any bulbs are burned out, replace them as soon as possible. Refer to the chart on page 255 to determine what type of replacement bulb is needed.


Maintenance


TAILLIGHT/BRAKE LIGHT


HIGH-MOUNT BRAKE LIGHT


TAILLIGHT


BACK-UP LIGHT


SIDE MARKER LIGHT


TURN SIGNAL


LICENSE PLATE LIGHT


Main MenuTable of Contentsst Headlight Aiming The headlights were properly aimed when your vehicle was new. You should check their aim if you regularly carry heavy items in the trunk or pull a trailer. Each headlight assembly has horizontal and vertical adjustment indicators. These are set to their "0" positions after the headlights are aimed at the factory.


To check these settings:


1. Make sure the fuel tank is full.


Park the vehicle on level ground.


2. The driver or someone who


weighs the same should be sitting in the driver's seat for all checks and adjustments. Load the trunk with the items you normally carry.


HORIZONTAL ANGLE GAUGE


VERTICAL ANGLE GAUGE


Lights


If you usually pull a trailer, load it as you would normally and attach it to the vehicle. Push down on the front and rear bumpers several times to make sure the vehicle is sitting normally.


3. Open the hood.


4. Check the horizontal angle gauge. The line on the adjustment screw indicator should line up with the "0" mark on the gauge.


BUBBLE


5. Check the vertical angle gauge. The bubble should be centered underneath the longest scribe mark on the gauge.


CONTINUED


Maintenance


Main MenuTable of Contentsst Lights


HORIZONTAL ADJUSTMENT


VERTICAL ADJUSTMENT


6. If either indicator is not aligned


with its "0" mark as described, an adjustment can be made using a Phillips-head screwdriver to realign it with the "0" mark. Please refer to the illustrations.


7. If you cannot get an indicator to


align, have your Honda dealer inspect the vehicle for body damage or suspension problems.


Maintenance


Replacing a Headlight Bulb Your car has two bulbs on each side, four in total. Make sure you are replacing the bulb that is burned out. Your car uses halogen headlight bulbs. When replacing a bulb, handle it by its plastic case and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.


The headlight bulbs in your car are H1 headlight bulbs for longer life. We recommend the use of Genuine Honda parts for replacing a headlight bulb.


NOTICE


Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.


Main MenuTable of Contentsst 1. Open the hood.


2. Remove the electrical connector from the bulb by squeezing the connector on both sides to unlock the tab. Pull the connector straight off.


BULB


HOLD- DOWN WIRE


WEATHER SEAL


CONNECTOR


3. Remove the rubber weather seal


by pulling on the tab.


4. Unclip the end of the hold-down wire from its slot. Pivot it out of the way and remove the bulb.


Lights


5. Insert the new bulb into the hole, making sure the tabs are in their slots. Pivot the hold-down wire back in place and clip the end into the slot.


6. Install the rubber seal over the back of the headlight assembly. Make sure it is right side up; it is marked "TOP".


7. Push the electrical connector onto


the tabs of the new bulb. Make sure it locks in place. Turn on the headlights to test the new bulb.


Maintenance


Main MenuTable of Contentsst Lights


Replacing a Parking Light Bulb 1. Open the hood. The front parking light is next to the headlight bulb.


If you need to change a bulb on the passenger's side, remove the radiator reserve tank by pulling it out of its holder.


3. Pull the bulb straight out of its


socket.


Push the new bulb straight into the socket until it bottoms.


4. Insert the socket back into the


headlight assembly. Turn it clockwise to lock it in place.


5. Turn on the parking lights to


make sure the new bulb works.


2. Remove the socket from the


headlight assembly by turning it one-quarter turn counterclockwise.


6. (Passenger's side)


Reinstall the radiator reserve tank.


Maintenance


Main MenuTable of Contentsst Replacing a Front Side Marker Light Bulb


BULB


SOCKET


SCREW


FRONT SIDE MARKER ASSEMBLY


1. Use a Phillips-head screwdriver to


remove the side marker assembly's mounting screw.


3. Remove the socket from the side


marker assembly by turning it one- quarter turn counterclockwise.


2. Remove the side marker assembly


from the bumper.


4. Pull the bulb straight out of its


socket.


Push the new bulb straight into the socket until it bottoms.


Lights


5. Insert the socket back into the side marker assembly. Turn it clockwise to lock it in place.


6. Test the side marker to make sure


the new bulb is working.


7. Put the side marker assembly into the bumper. Make sure the tab on the side marker assembly fits into the bumper slot. Tighten the mounting screw.


Maintenance


Main MenuTable of Contentsst Lights


Replacing a Front Turn Signal Light Bulb


TURN SIGNAL ASSEMBLY


BULB


5. Insert the socket back into the


turn signal assembly. Turn it clockwise to lock it in place.


6. Test the lights to make sure the


new bulb is working.


7. Put the turn signal assembly into


the bumper. Make sure the tab on the turn signal assembly fits into the bumper slot. Tighten the mounting screw.


SCREW


SOCKET


1. Use a Phillips-head screwdriver to loosen the turn signal assembly's mounting screw.


3. Remove the socket from the turn signal assembly by turning it one- quarter turn counterclockwise.


2. Remove the turn signal assembly


from the bumper.


4. Pull the bulb straight out of its


socket. Push the new bulb straight into the socket until it bottoms.


Maintenance


Main MenuTable of Contentsst Replacing Rear Bulbs


Lights


1. Open the trunk.


2. Undo the fastener on the side of


the trunk lining by pushing on the center of the fastener's head until it pops in. Pull the lining back.


3. Determine which of the five bulbs is burned out: stop/taillight, turn signal light, side marker light, back-up light, or taillight.


5. Pull the bulb straight out of its


socket. Push the new bulb straight into the socket until it bottoms.


4. Remove the socket by turning it


one-quarter turn counterclockwise.


CONTINUED


Maintenance


Main MenuTable of Contentsst Lights


6. Reinstall the socket into the light assembly by turning it clockwise until it locks.


7. Test the lights to make sure the


new bulb is working.


8. Reinstall the trunk lining.


9. Reset the fastener by pushing on the pointed end until it pops back almost flush with the fingers on the housing.


10. Put the fastener in the hole in the side of the trunk lining and push on the center until it locks (the center is flush with the head).


Maintenance


Main MenuTable of Contentsst Replacing a High-mount Brake Light Bulb (Except Type SH model)


HIGH-MOUNT BRAKE LIGHT ASSEMBLY


1. Remove the high-mount brake


light assembly by pushing it slightly toward the rear windshield and sliding it out of the rear shelf.


2. Remove the socket from the light assembly by turning it one-quarter turn counterclockwise.


3. Pull the bulb straight out of its


socket. Push the new bulb straight into the socket until it bottoms.


Lights


4. Reinstall the socket. Turn it


clockwise until it locks.


5. Test the lights to make sure the


new bulb is working.


6. Reinstall the high-mount brake


light assembly on the rear shelf. Make sure the tabs on the high- mount brake light assembly fit into the slots.


Maintenance


Main MenuTable of Contentsst Lights


Replacing a Rear License Bulb


4. Turn on the parking lights and


check that the new bulb is working.


5. Put the license light assembly in


place. Reinstall the two screws and tighten them securely.


1. Use a Phillips-head screwdriver to


remove the two screws holding the license plate light assembly to the bracket. Pull the assembly away from the bracket.


2. Remove the socket from the light


assembly by turning it one-quarter turn counterclockwise.


3. Pull the bulb straight out of its


socket. Push the new bulb in until it bottoms in the socket.


Maintenance


Main MenuTable of Contentsst Replacing Bulbs in the Interior Courtesy Lights The courtesy lights in the doors and roof come apart the same way. They do not all use the same bulb. The spotlight bulbs are in the ceiling light housing.


1. Remove the lens by carefully


prying on the edge of the lens with a fingernail file or a small flat-tip screwdriver. Do not pry on the edge of the housing around the lens.


Ceiling light:


Pry on the front edge of the lens in the middle.


On Type SH


Door light:


Pry on the top middle of the lens.


CEILING LIGHT


DOOR LIGHT


Lights


2. Remove the bulb by pulling it straight out of its metal tabs.


3. Push the new bulb into the metal tabs. Snap the lens back in place.


Maintenance


Main MenuTable of Contentsst Lights


Replacing the Trunk Light Bulb


TRUNK LIGHT


1. Open the trunk. Pull down the


trunk light cover.


2. Remove the bulb by pulling it straight out of its metal tabs.


3. Push the new bulb into the metal


tabs.


4. Push the cover back in place.


Maintenance


Main MenuTable of Contentsst If you need to park your vehicle for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors.


Fill the fuel tank.


Change the engine oil and filter (see page 175).


Wash and dry the exterior completely.


Clean the interior. Make sure the carpeting, floor mats, etc. are completely dry.


Leave the parking brake off. Put the transmission in Reverse (5- speed manual) or Park (automatic).


Storing Your Vehicle


Block the rear wheels.


If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.


Leave one window open slightly (if the vehicle is being stored indoors).


Disconnect the battery.


Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield.


To minimize sticking, apply a silicone spray lubricant to all door and trunk seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and trunk seals.


Cover the vehicle with a "breathable" vehicle cover, one made from a porous material such as cotton. Nonporous materials, such as plastic sheeting, trap moisture, which can damage the paint.


If possible, run the engine for a while periodically (preferably once a month).


If you store your vehicle for 12
months or longer, have your Honda dealer perform the inspections called for in the 24 months/30,000 miles (48,000 km) maintenance schedule (Normal Conditions) as soon as you take it out of storage (see page 164). The replacements called for in the maintenance schedule are not needed unless the vehicle has actually reached that time or mileage.


Maintenance


Main MenuTable of Contentsst Appearance Care


Regular cleaning and polishing of your Honda helps to keep it "new" looking. This section gives you hints on how to clean your vehicle and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion.


Exterior Care.................................. 220
Washing......................................220
Waxing........................................221
Aluminum Wheels.....................221
Paint Touch-up........................... 221
Interior Care................................... 222
Carpeting.................................... 222
Fabric.......................................... 222
Vinyl............................................ 222
Seat Belts.................................... 223
Windows..................................... 223
Air Fresheners........................... 224
Corrosion Protection..................... 224
Body Repairs.................................. 225


Appearance Care


Main Menust Exterior Care


Washing Frequent washing helps preserve your vehicle's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish.


Wash your vehicle in a shady area, not in direct sunlight. If the vehicle is parked in the sun, move it into the shade and let the exterior cool down before you start.


Only use the solvents and cleaners recommended in this Owner's Manual.


NOTICE


Chemical solvents and strong cleaners can damage the paint, metal, and plastic on your vehicle.


Appearance Care


When you have washed and rinsed the whole exterior, dry it with a chamois or soft towel. Letting it air-dry will cause dulling and water spots.


As you dry the vehicle, inspect it for chips and scratches that could allow corrosion to start. Repair them with touch-up paint (see page 221).


Rinse the vehicle thoroughly with cool water to remove loose dirt.


Fill a bucket with cool water. Mix in a mild detergent, such as dishwashing liquid or a product made especially for vehicle washing.


Wash the vehicle using the water and detergent solution and a soft- bristle brush, sponge, or soft cloth. Start at the top and work your way down. Rinse frequently.


Check the body for road tar, tree sap, etc. Remove these stains with tar remover or turpentine. Rinse it off immediately so it does not harm the finish. Remember to re- wax these areas, even if the rest of the vehicle does not need waxing.


Main MenuTable of Contentsst Waxing Always wash and dry the whole vehicle before waxing it. You should wax your vehicle, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing.


You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products:


Waxes — A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc. You should use a wax on your Honda when it is new.


Polishes — Polishes and cleaner/ waxes can restore the shine to paint that has oxidized and lost some of its shine. They normally contain mild abrasives and solvents that remove


the top layer of the finish. You should use a polish on your Honda if the finish does not have its original shine after using a wax.


Cleaning tar, insects, etc. with removers also takes off the wax. Remember to re-wax those areas, even if the rest of the vehicle does not need waxing.


Aluminum Wheels Clean your Honda's aluminum alloy wheels as you do the rest of the exterior. Wash them with the same solution, and rinse them thoroughly.


The wheels have a protective clear- coat that keeps the aluminum from corroding and tarnishing. Using harsh chemicals, including some commercial wheel cleaners, or stiff brushes can damage this clear-coat. Only use a mild detergent and soft brush or sponge to clean the wheels.


Exterior Care


Paint Touch-up Your dealer has touch-up paint to match your vehicle's color. The color code is printed on a sticker on the driver's doorjamb. Take this code to your dealer so you are sure to get the correct color.


Inspect your vehicle frequently for chips or scratches in the paint. Repair them right away to prevent corrosion of the metal underneath. Use the touch-up paint only on small chips and scratches. More extensive paint damage should be repaired by a professional.


Appearance Care


Main MenuTable of Contentsst Interior Care


Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam.


Fabric Vacuum dirt and dust out of the material frequently. For general cleaning, use a solution of mild soap and lukewarm water, letting it air dry. To clean off stubborn spots, use a commercially-available fabric cleaner. Test it on a hidden area of the fabric first, to make sure it does not bleach or stain the fabric. Follow the instructions that come with the cleaner.


Vinyl Remove dirt and dust with a vacuum cleaner. Wipe the vinyl with a soft cloth dampened in a solution of mild soap and water. Use the same solution with a soft-bristle brush on more difficult spots. You can also use commercially-available spray or foam-type vinyl cleaners.


Appearance Care


Main MenuTable of Contentsst Seat Belts


LOOP


Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.


If your seat belts get dirty, you can use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. They can weaken the belt material. Let the belts air- dry before you use the vehicle.


Interior Care


Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows. Use a soft cloth or paper towels to clean all glass and clear plastic surfaces.


NOTICE


The rear window defogger and antenna wires are bonded to the inside of the glass. Wiping vigorously up-and- down can dislodge and break these wires. When cleaning the rear window, use gentle pressure and wipe side-to- side.


Appearance Care


Main MenuTable of Contentsst Interior Care, Corrosion Protection


Air Fresheners If you want to use an air freshener/ deodorizer in the interior of your vehicle, it is best to use a solid type. Some liquid air fresheners contain chemicals that may cause parts of the interior trim and fabric to crack or discolor.


If you use a liquid air freshener, make sure you fasten it securely so it does not spill as you drive.


Corrosion Protection Two factors normally contribute to causing corrosion in your vehicle:


Inspect and clean out the drain holes in the bottom of the doors and body.


1. Moisture trapped in body cavities. Dirt and road salt that collects in hollows on the underside of the vehicle stays damp, promoting corrosion in that area.


2. Removal of paint and protective coatings from the exterior and underside of the vehicle.


Many corrosion-preventive measures are built into your Honda. You can help keep your vehicle from corroding by performing some simple periodic maintenance:


Repair chips and scratches in the paint as soon as you discover them.


Check the floor coverings for dampness. Carpeting and floor mats may remain damp for a long time, especially in winter. This dampness can eventually cause the floor panels to corrode.


Use a high-pressure spray to clean the underside of your vehicle. This is especially important in areas that use road salt in winter. It is also a good idea in humid climates and areas subject to salt air. Be careful of the ABS wheel sensors and wiring at each wheel.


Have the corrosion-preventive coatings on the underside of your vehicle inspected and repaired periodically.


Appearance Care


Main MenuTable of Contentsst Body repairs can affect your vehicle's resistance to corrosion. If your vehicle needs repairs alter a collision, pay close attention to the parts used in the repair and the quality of the work.


Make sure the repair facility uses Genuine Honda replacement body parts. Some companies make sheet metal pieces that seem to duplicate the original Honda body parts, but are actually inferior in fit, finish, and corrosion resistance. Once installed, they do not give the same high- quality appearance.


When reporting your collision to the insurance company, tell them you want Genuine Honda parts used in the repair. Although most insurers recognize the quality of original parts, some may try to specify that the repairs be done with other available parts. You should investi- gate this before any repairs are begun.


Take your vehicle to your authorized Honda dealer for inspection after the repairs are completed. He can make sure that quality materials were used, and that corrosion-preventive coatings were applied to all repaired and replaced parts.


Body Repairs


Appearance Care


Main MenuTable of Contentsst Taking Care of the Unexpected


This section covers the more- common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed.


Compact Spare Tire....................... 228
Changing a Flat Tire ..................... 229
If Your Engine Won't Start........... 234


Nothing Happens or the Starter Motor Operates Very Slowly.............................235


The Starter Operates


Normally................................. 236
Jump Starting................................. 236
If Your Engine Overheats............. 238
Low Oil Pressure Indicator.......... 240
Charging System Indicator........... 241
Malfunction Indicator Lamp ........ 242
Brake System Indicator................ 243
Closing the Moonroof................... 244
Fuses............................................... 245
Checking and Replacing........... 246
Towing............................................ 250


Taking Care of the Unexpected


Main Menust Compact Spare Tire


Your vehicle has a compact spare tire that takes up less space. Use this spare tire as a temporary replace- ment only. Get your regular tire repaired or replaced and put back on your vehicle as soon as you can.


Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm2)


Taking Care of the Unexpected


Follow these precautions whenever you are using the compact spare tire:


INDICATOR LOCATION MARK


Do not exceed 50 mph (80 km/h) under any circumstances.


This tire gives a harsher ride and less traction on some road sur- faces than the regular tire. Use greater caution while driving on this tire.


Do not mount snow chains on the compact spare.


The wheel of the compact spare tire is designed especially to fit your vehicle. Do not use your spare tire on another vehicle unless it is the same make and model.


TREAD WEAR INDICATOR BAR


The compact spare tire has a shorter tread life than a regular tire. Replace it when you can see the tread wear indicator bars. The replacement should be the same size and design tire, mounted on the same wheel. The compact spare tire is not designed to be mounted on a regular wheel, and the compact wheel is not designed for mounting a regular tire.


Main MenuTable of Contentsst If you have a flat tire while driving, stop in a safe place to change it. Stopping in traffic or on the shoulder of a busy road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes.


The vehicle can easily roll off the jack, seriously injuring anyone underneath.


Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.


Changing a Flat Tire


JACK


TRUNK FLOOR


3. Open the trunk. Raise the trunk


floor by lifting up on the back edge.


4. Take the tool kit out of the trunk.


5. Unscrew the wing bolt and take


the spare tire out of its well.


TOOL KIT


SPARE TIRE


1. Park the vehicle on firm, level


ground away from traffic. Turn on the hazard warning lights and turn the ignition switch to LOCK (0).


2. Put the transmission in Park


(automatic) or Reverse (manual). Apply the parking brake. Have all of the passengers get out of the vehicle while you change the tire.


CONTINUED


Taking Care of the Unexpected


Main MenuTable of Contentsst Changing a Flat Tire


Loading...
x