2011 Honda Odyssey Owners Manual

the information display, depending on models. For more information, see page

670

Low Oil Pressure Indicator

The engine can be severely damaged if this indicator flashes or stays on when the engine is running. For more information, see page

669

OnTouringmodels You will also see a ‘‘CHECK ENGINE OIL LEVEL’’ message on the multi-information display (see page

91

).

2011 Odyssey10/07/17 09:43:19 31TK8600_072

Instrument Panel Indicators

2.

If it remains on after you have fully released the parking brake while the engine is running, or if it comes on while driving, there could be a problem with the brake system. For more information, see page

672

OnTouringmodels You will also see a ‘‘BRAKE FLUID LOW’’ or ‘‘CHECK BRAKE SYSTEM’’ message on the multi-information display (see page

90

).

U.S.

Canada

Parking Brake and Brake System Indicator (Red)

This indicator has two functions:

1.

It comes on when you turn the ignition switch to the ON (II) position. It is a reminder to check the parking brake. A beeper sounds if you drive with the parking brake not fully released. Driving with the parking brake not fully released can damage the brakes and tires.

OnTouringmodels You will also see a ‘‘RELEASE PARKING BRAKE’’ message on the multi-information display (see page

) .

90

Supplemental Restraint System (SRS) Indicator This indicator comes on for several seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates a potential problem with your front airbags. This indicator will also alert you to a potential problem with your airbag system components. For more information, see page

32

OnTouringmodels You will also see a ‘‘CHECK AIRBAG SYSTEM’’ message on the multi-information display (see page

90

).

67

2011 OdysseyOnTouringmodels You will also see a ‘‘CHECK ABS SYSTEM’’ message on the multi- ). 91
information display (see page

Anti-lock Brake System (ABS) Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, there is a problem with the ABS. If this happens, have your vehicle checked at a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function. For more information, see page 568

10/07/17 09:43:27 31TK8600_073

Instrument Panel Indicators

U.S.

Canada

Side Airbag Off Indicator

This indicator comes on for several seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. For more information, see page 33

OnTouringmodels You will also see a ‘‘PASSENGER SIDE AIRBAG OFF’’ message on the ). multi-information display(seepage 90

68

2011 Odyssey10/07/17 09:43:37 31TK8600_074

Immobilizer System Indicator

This indicator comes on briefly when you turn the ignition switch to the ON (II) position. It will then go off if you have inserted a properly coded ignition key. If it is not a properly coded key, the indicator will blink, and the engine’s fuel system will be disabled (see page

145

).

Instrument Panel Indicators

VSA OFF Indicator

It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. For more information, see page

570

Vehicle Stability Assist (VSA) System Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

It flashes when VSA is active (see page

570

).

If it comes on and stays on at any other time, there is a problem with the VSA system. Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. See page information on the VSA system.

570

for more

OnTouringmodels You will also see a ‘‘CHECK VSA SYSTEM’’ message on the multi- information display (see page 91

).

69

2011 Odyssey10/07/17 09:43:46 31TK8600_075

Instrument Panel Indicators

U.S.

Canada

Starter System Indicator

This indicator comes on when there is a problem with the starter system. For more information, see page 559

OnTouringmodels If you see a ‘‘CHECK STARTER SYSTEM’’ message on the multi- information display, there is a problem with the starter system (see page

92

).

70

If the indicator comes on at any other time, there is a problem with BSI. You will also see a ‘‘CHECK BLIND SPOT SYSTEM’’ message on the multi-information display. If this happens, take your vehicle to a dealer, and have it checked (For more information, see page ). 579
When this indicator is on, BSI is not working.

Blind Spot Information System (BSI) Indicator

OnTouringmodels This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

The BSI indicator also comes on if the rear bumper becomes dirty while driving. You will see a ‘‘BLIND SPOT NOT AVAILABLE’’ message on the multi-information display. When you clean the rear bumper, the indicator should go off after you begin driving again.

When you turn the system on, the indicator will turn off.

2011 Odyssey10/07/17 09:43:55 31TK8600_076

Low Tire Pressure Indicator

OnLX,EX,EX-Lmodels This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.

If this happens, pull to the side of the road when it is safe, check which tire has lost pressure, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service (see page information, see page

). For more 572

655

683

Instrument Panel Indicators

If this happens, pull to the side of the road when it is safe, check which tire has lost pressure, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service. Refer to page information.

for more

655

574

Low Tire Pressure/ TPMS Indicator

OnTouringmodels This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

This indicator has two functions:

1.

If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.

You will also see a ‘‘CHECK TIRE PRESSURE’’ message on the multi- information display (see page ).

91

CONTINUED

71

2011 Odyssey10/07/17 09:44:02 31TK8600_077

Instrument Panel Indicators

2.

If this indicator begins to flash, there is a problem with the tire pressure monitoring system (TPMS). You will also see a ‘‘CHECK TPMS SYSTEM’’ message on the multi-information display. The indicator continues to flash for a while (approximately 1
minute), then stays on. If this happens, have your dealer check the system as soon as possible. For more information, see page

577

Tire Pressure Monitoring System (TPMS) Indicator

OnLX,EX,EX-Lmodels This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the TPMS. With this indicator on, the low tire pressure indicator will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked. For more information, see page 573

72

Turn Signal and Hazard Warning Indicators

The left or right turn signal indicator blinks when you signal a lane change or turn. If an indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is ). burned out (see pages and Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.

628

631

When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.

2011 Odyssey10/07/17 09:44:12 31TK8600_078

Lights On Indicator

or

This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the position. If you turn the

ignition switch to the ACCESSORY (I) or the LOCK (0) position without turning off the light switch, this indicator will remain on. A reminder chime will also sound when you open the driver’s door without the key in the ignition switch.

OnallmodelsexceptLX This indicator also comes on when the light switch is in AUTO and the lights turn on automatically.

Daytime Running Lights Indicator

If this indicator comes on when the ignition switch is turned to the ON (II) position and the parking brake is released, it means there is a problem in the high beam headlight’s circuit. Have your vehicle checked by your dealer.

OnTouringmodels If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem in the high beam headlight’s circuit. Take your vehicle to a dealer to have it checked (see page

92

).

Instrument Panel Indicators

High Beam Indicator

This indicator comes on with the high beam headlights. For more information, see page

137

Fog Light Indicator OnTouringmodels

This indicator comes on when you turn on the fog lights. See page for information on fog light 139
operation.

73

2011 Odyssey10/07/19 15:50:48 31TK8600_079

Instrument Panel Indicators

Washer Level Indicator OnCanadianmodels

WASHER LEVEL INDICATOR

Low Fuel Indicator

OnTouringmodels You will also see a ‘‘FUEL LOW’’ message on the multi-information display (see page

92

).

U.S.

Canada

Power Tailgate Indicator

OnEX-Lmodels This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, there is a problem in the power tailgate system. Have the system checked by your dealer as soon as possible. You can still open or close the tailgate manually. For more information on the power tailgate, see page

162

OnTouringmodels You will also see a ‘‘CHECK POWER TAILGATE SYSTEM’’ message on the multi-information display.

LOW FUEL INDICATOR

This indicator is in the fuel gauge. It comes on as a reminder that you must refuel soon.

When the indicator comes on, there are about 3.0 US gal (11.4 ) of fuel remaining in the tank.

When the needle reaches E, there is a very small amount of fuel in the tank.

This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator come on (see page

620

).

OnCanadianTouringmodels You will also see a ‘‘WASHER FLUID LOW’’ message on the multi- information display (see page

92

).

74

2011 Odyssey10/07/17 09:44:36 31TK8600_080

U.S.

Canada

Power Sliding Door Indicator

OnEXandEX-Lmodels This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, there is a problem in the power sliding door system. With this indicator on, move the main switch on the dashboard to the OFF position, and have the system checked by your dealer as soon as possible. You can still open or close each sliding door manually. For more information on the power sliding doors, see page

167

OnTouringmodels You will also see a ‘‘CHECK LEFT SLIDING DOOR’’ or ‘‘CHECK RIGHT SLIDING DOOR’’ message on the multi-information display.

Instrument Panel Indicators

Cruise Main Indicator

Door and Tailgate Open Indicator

This indicator comes on when you turn on the cruise control system by pressing the CRUISE button on the steering wheel (see page

480

).

Cruise Control Indicator

This indicator comes on when you set the cruise control. See page 480
cruise control.

for information on operating the

Fuel Economy Indicator

While the engine is operating in its most economical range, this indicator may come on and stay on. It goes off when your vehicle uses extra fuel.

The appropriate light comes on in this indicator if the tailgate or any door is not closed tightly. All the lights in the indicator come on for a few seconds when you turn the ignition switch to the ON (II) position.

OnTouringmodels The door and tailgate open indicator also appears on the multi-information display.

75

2011 Odyssey10/07/17 09:44:46 31TK8600_081

Instrument Panel Indicators

Maintenance Minder Indicator

OnLX,EX,EX-Lmodels This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. It reminds you that it is time to take your vehicle in for scheduled maintenance. The maintenance main items and sub items will be displayed in the information display. See page 599
Maintenance Minder .

for more information on the

TM

This indicator goes off when your dealer resets it after completing the required maintenance service.

76

System Message Indicator OnTouringmodels This indicator comes on when there is a system message on the multi- information display. Press the INFO button on the steering wheel (see ) to see the message (see page page ).

83
90

Most of the time, this indicator comes on along with other indicators in the instrument panel such as the seat belt reminder indicator, SRS indicator, VSA system indicator, etc.

Security System Indicator OnallmodelsexceptLX

SECURITY SYSTEM INDICATOR

This indicator comes on when the security system is set. For more information, see page

479

2011 Odyssey10/07/17 09:44:53 31TK8600_082

INFORMATION DISPLAY/ MULTI-INFORMATION DISPLAY

TACHOMETER

SPEEDOMETER

TEMPERATURE GAUGE

FUEL GAUGE

Gauges

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. Turn to page for instructions and precautions on checking the engine cooling system. Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.

667

U.S. Touring model is shown.

SELECT/RESET KNOB

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

77

2011 Odyssey10/07/17 09:45:05 31TK8600_083

Gauges

INFORMATION DISPLAY

: Press the select/reset knob.

RANGE (ESTIMATED DISTANCE)

ODOMETER

OUTSIDE TEMPERATURE INDICATOR

ENGINE OIL LIFE

TRIP METER B

U.S. model with outside temperature indicator is shown.

INSTANT FUEL ECONOMY

TRIP METER A

AVERAGE FUEL ECONOMY

Information Display OnLX,EX,EX-Lmodels The information display shows the odometer, trip meter, engine oil life, outside temperature (if equipped), instant fuel economy, average fuel economy, range (estimated distance), and maintenance item code(s).

To switch the display, press and release the select/reset knob repeatedly. When you turn the ignition switch to the ON (II) position, your last selection is displayed.

OnTouringmodels For information about the multi- information display, see page 83

78

Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

TripMeter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the select/reset knob repeatedly. Each trip meter works independently, so you can keep track of two different distances. To reset a trip meter, display it, and then press and hold the select/reset knob until the number resets to ‘‘0.0’’.

2011 Odyssey10/07/17 09:45:12 31TK8600_084

InstantFuelEconomy This display shows the instant fuel economy you are getting.

It shows the number of mpg (U.S.) or l/100 km (Canada).

AverageFuelEconomy When either of the trip meters (trip A or B) is displayed, your vehicle’s average fuel economy since you last reset that trip meter can be shown on the information display (mpg on U.S. models and l/100 km on Canadian models). This number is updated once per 10 seconds. To see the average fuel economy, press and release the select/reset knob repeatedly.

When you reset a trip meter, the average fuel economy for that trip meter also resets.

Gauges

Range(EstimatedDistance) This display shows the estimated distance you can travel on the fuel remaining in the tank.

This distance is estimated from the fuel economy you have achieved over the last few miles (kilometers), so it will vary with changes in speed, traffic condition, etc.

79

2011 Odyssey10/07/17 09:45:19 31TK8600_085

Gauges

OutsideTemperatureIndicator ExceptLXmodel This indicator displays the outside temperature in Fahrenheit (U.S. models) or Celsius (Canadian models).

The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.

80

If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.

5°F in U.S. models (

±

The temperature must be

NOTE: stabilized before doing this procedure.

OUTSIDE TEMPERATURE DISPLAY

: Press and release the select/reset knob.

To adjust the outside temperature display, press and hold the select/ reset knob for 10 seconds. The display changes as shown above.

2011 Odyssey10/07/17 09:45:25 31TK8600_086

Select the outside temperature display by pressing and releasing the select/reset knob. Press and hold the same knob for a few seconds to enter this setting, then turn it to adjust the temperature. The following sequence will appear for 3, each: 0, 1, 2, 3, 4, 5, 2, − − − −

5, 1, 0 (U.S.) or 0, 1, 2, 3, 1, 0 (Canada).

− − − −

4, 3,

2,

When the temperature reaches the desired value, release the select/ reset knob. You should see the new outside temperature displayed.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

BatteryChargeLow When the battery’s state of charge is low, the vehicle’s battery management system triggers a ‘‘BATT LOW’’ message if the ignition switch is on or off.

Depending on how low the battery’s state of charge dropped and how long it remained low, these messages may occur frequently. It may take a number of trips to sufficiently recharge the battery and the messages to no longer appear.

Gauges

−

IGN ON (II) Immediately turn off all electrical devices (interior lights, air conditioning, audio, heated seats, etc.). Try not to operate other electrically operated controls such as the power windows. Driving the vehicle will recharge the battery. If the message continues to display while driving, see your dealer.

IGN ACCESSORY (I) or LOCK (0) Follow the message and turn off − all electrical devices. Driving the vehicle will recharge the battery, however the vehicle may not start. If it does not start, see jump starting (see page dealer.

), or contact your

665

81

2011 Odyssey10/07/17 09:45:32 31TK8600_087

Gauges

TM

MaintenanceMinder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.

599

for

82

If the system still detects a leak in your vehicle’s evaporative emissions system, the malfunction indicator lamp (MIL) comes on. If the fuel fill cap was not already tightened, turn the engine off, and check or retighten the fuel fill cap until it clicks at least once. The MIL should go off after several days of normal driving once the cap is tightened or replaced. If the MIL does not go off, have your vehicle inspected by a dealer. For more information, see page

671

CheckFuelCapMessage Your vehicle’s onboard diagnostic system will detect a loose or missing fuel fill cap as an evaporative system leak. The first time a leak is detected a ‘‘CHECK FUEL CAP’’ message appears on the information display.

Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen it, then retighten it until it clicks at least once. The message should go off after several days of normal driving once you tighten or replace the fuel fill cap. To scroll to another display, press the select/reset knob.

The ‘‘CHECK FUEL CAP’’ message will appear each time you restart the engine until the system turns the message off.

2011 Odyssey10/07/17 09:45:40 31TK8600_088

OnTouringmodels The multi-information display in the instrument panel displays various information and messages when the ignition switch is in the ON (II) position. Some of the messages help you operate your vehicle more comfortably. Others help to keep you aware of the periodic maintenance your vehicle needs for continued trouble-free driving.

There are two types of messages; normal display messages and system messages.

You can select the displayed language and also customize some vehicle control settings to your liking with the multi-information display and the three buttons on the steering wheel.

Multi-Information Display

Normal Display Messages

UPPER SEGMENT

INFO (

▲ ▼

) BUTTON

LOWER SEGMENT U.S. model is shown.

The multi-information display consists of two segments: an upper segment and a lower segment.

In the normal display mode, the upper segment displays trip computer information, such as fuel economy or average speed. The lower segment displays the odometer/trip meter (A/B), outside temperature, and engine oil life and maintenance item code(s).

SEL/RESET BUTTON

To change the display, press the SEL/RESET button or INFO ( / ▲ ) button on the steering wheel ▼ repeatedly until the desired information appears (see page

84

).

When you turn the ignition switch to the ON (II) position, your last selection is displayed.

CONTINUED

83

2011 Odyssey10/07/17 09:45:44 31TK8600_089

Multi-Information Display

U.S. model is shown.

84

: Press the INFO ( ) button. : Press the SEL/RESET button.

▲ ▼

2011 Odyssey10/07/17 09:45:52 31TK8600_090

Odometer

Trip Meter

U.S.

Canada

U.S.

Canada

ODOMETER

The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

TRIP METER A

TRIP METER B

This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Each trip meter works independently, so you can keep track of two different distances.

Multi-Information Display

To reset a trip meter, display it, and then press and hold the SEL/RESET button until the number resets to ‘‘0.0.’’

When you reset Trip A, average fuel economy A is reset at the same time. When you reset Trip B, average fuel economy B is reset.

In the customizing mode, you can set Trip A and average fuel economy A to reset at the same time when you refuel your vehicle (see page ).

105

85

2011 Odyssey10/07/17 09:46:01 31TK8600_091

Multi-Information Display

Outside Temperature

U.S.

Canada

OUTSIDE TEMPERATURE

The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.

This shows the outside Fahrenheit temperature in U.S. models, and Celsius temperature in Canadian models.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

You can adjust the outside temperature display (see page

103

).

Engine Oil Life

ENGINE OIL LIFE

This shows the remaining engine oil life. It shows 100% after the engine oil is replaced and the display is reset. The engine oil life is calculated based on engine operating conditions. For more information, see page

599

86

2011 Odyssey10/07/17 09:46:07 31TK8600_092

Battery Charge Low When the battery’s state of charge is low, the vehicle’s battery management system triggers one of the following ‘‘BATTERY CHARGE LOW’’ messages if the ignition switch is on or off.

Depending on how low the battery’s state of charge dropped and how long it remained low, these messages may occur frequently. It may take a number of trips to sufficiently recharge the battery and the messages to no longer appear.

−

IGN ON (II) Immediately turn off all electrical devices (interior lights, air conditioning, audio, heated seats, etc.). Try not to operate other electrically operated controls such as the power windows. Driving the vehicle will recharge the battery. If the message continues to display while driving, see your dealer.

Multi-Information Display

IGN ACCESSORY (I) or LOCK (0) Follow the message and turn off − all electrical devices. Driving the vehicle will recharge the battery, however the vehicle may not start. If it does not start, see jump starting (see page dealer.

), or contact your

665

87

2011 Odyssey10/07/17 09:46:17 31TK8600_093

Multi-Information Display

Trip Computer Along with the trip meter, the trip computer calculates these values:

Instant Fuel Economy Average Fuel Economy Range Elapsed Time Average Vehicle Speed

INSTANTFUELMPG(U.S. models)/INSTANTFUELL/100km (Canadianmodels) This shows your instant fuel economy.

AVERAGEFUELA/B This shows your vehicle’s average fuel economy in mpg (U.S. models) or l/100 km (Canadian models) since you last reset Trip A or Trip B.

RANGE This shows the estimated distance you can travel on the fuel remaining in the fuel tank. This distance is estimated from the fuel economy you received over the last several miles (U.S.) or kilometers (Canada), so it will vary with changes in speed, traffic, etc.

You can customize the Trip A and AVERAGE FUEL A reset condition on the multi-information display (see page

105

).

88

2011 Odyssey10/07/17 09:46:28 31TK8600_094

ELAPSEDTIME This shows the accumulated traveling time since you last reset it. When you turn the ignition switch to the ON (II) position, ELAPSED TIME is reset. If you want to reset the ELAPSED TIME manually, go to the trip computer’s ELAPSED TIME display, and press and hold the SEL/RESET button until the number resets. You can customize the ELAPSED TIME reset conditions on the multi- ). information display (see page

107

AVERAGESPEED This shows the average speed you are traveling in miles per hour (mph) for U.S. models or kilometers per hour (km/h) for Canadian models.

To reset the AVERAGE SPEED you have traveled, press and hold the SEL/RESET button until the number resets.

System Messages

SYSTEM MESSAGE INDICATOR

If there is a problem with your vehicle, for example the engine oil level is low or a door is not fully closed, the multi-information display will show you the problem. It does this by interrupting the current display with one or more messages.

Multi-Information Display

The system message(s) triggers the appropriate indicator(s) on the instrument panel, including the system message indicator, to come on. The system message indicator does not go off until the problem(s) is corrected.

You will also hear a beep when the system message comes on for the first time.

If there are several messages, each message is displayed for about 5
seconds.

To switch the message(s) before 5
seconds elapsed or select the normal display, press the INFO ( / ) ▲ ▼ button on the steering wheel repeatedly.

89

2011 Odyssey10/07/17 09:46:40 31TK8600_095

Multi-Information Display

If the system message indicator remains lit on the instrument panel, you can see the corresponding message(s) again by pressing the INFO ( / ) button repeatedly.

▲ ▼

Even if you switch the display from the message to the normal display, some important messages come on again at regular intervals until the problem is corrected.

Here is a list of all messages:

90

See page

11

See page

20

See page

20

See page

32

See page

33

U.S.

Canada

U.S.

Canada

U.S.

Canada

See page

199

See page

672

See page

672

U.S.

Canada

2011 Odyssey10/07/17 09:46:52 31TK8600_096

Multi-Information Display

See page

670

See page

670

See page

649

See page

87

See page

87

See page

671

U.S.

Canada

U.S.

Canada

See page

669

See page

568

See page

570

See page

575

See page

576

See page

667

See page

162

See page

167

CONTINUED

91

2011 Odyssey10/07/17 09:47:04 31TK8600_097

Multi-Information Display

U.S.

Canada

92

See page

560

See page

561

See page

490

See page

74

See page

74

See page

543

See page

147

See page

147

See page

487

See page

139

See page

586

See page

586

See page

604

2011 Odyssey10/07/17 09:47:14 31TK8600_098

Customized Settings OnTouringModels You can customize some vehicle control settings. To change the settings, the ignition switch must be in the ON (II) position, and the vehicle must be stopped with the transmission in Park.

To enter the customizing mode, press either INFO button ( / ) ▲ ▼ repeatedly until ‘‘CUSTOMIZE SETTINGS’’ is displayed, then press the SEL/RESET button.

If you try to enter the customizing mode while the vehicle is moving, you will see a ‘‘MUST STOP AND SHIFT TO PARK TO CHANGE SETTINGS’’ message and you cannot change the settings.

DRIVER’S ID

You can customize some vehicle control settings for ‘‘DRIVER 1’’ and ‘‘DRIVER 2’’ separately. If ‘‘DRIVER 1’’ or ‘‘DRIVER 2’’ is not displayed, customizing is not possible.

To have the driver’s ID detected, make sure your remote transmitter is linked to the system and the driver’s door is unlocked with a corresponding remote transmitter.

Multi-Information Display

If you want the settings as they were when the vehicle left the factory, select DEFAULT ALL, as described on page

96

If you want to change any vehicle control settings, select CHANGE SETTINGS, then press the SEL/ RESET button.

Refer to the table on the next page about the settings you can customize.

CONTINUED

93

2011 Odyssey10/07/17 09:47:19 31TK8600_099

Multi-Information Display

Group Setup METER SETUP (P.100)

Menu Item

LANGUAGE SELECTION

Description

Setting Option

Changes the language used in the display.

ADJUST OUTSIDE TEMP. DISPLAY

Changes the outside temperature reading above or below its current reading.

TRIP A RESET WITH REFUEL ELAPSED TIME RESET

MEMORY POSITION LINK INTERIOR LIGHT DIMMING TIME

Causes trip meter A and the average fuel economy to reset when you refuel. Resets the elapsed time of your current trip.

Changes the driver’s seat and the outside mirror positions to a stored setting. Changes how long (in seconds) the interior lights stay on after you close the doors and the tailgate.

HEADLIGHT AUTO OFF TIMER

Changes how long (in seconds) the exterior lights stay on after you close the driver’s door.

AUTO LIGHT SENSITIVITY

Changes the timing of when the headlights come on. The headlight switch needs to be in the AUTO position.

POSITION SETUP (P.109) LIGHTING SETUP (P.112)

＊

Default setting

94

＊

〜 〜 ＊

5°F (U.S.) 3°C

＊

＊

＊

5°F 3°C

0°F 0°C

ENGLISH FRENCH SPANISH − 〜± − 〜± (Canada) ON OFF IGN OFF TRIP A RESET TRIP B RESET ON OFF 15 sec 30 sec 60 sec 0 sec 15 sec 30 sec 60 sec MAX HIGH MID

＊

＊

＊

＊

LOW MIN

Page 101

103

105

107

110

113

115

117

2011 Odyssey10/07/17 09:47:14 31TK8600_098

Group Setup

DOOR SETUP (P.119)

Menu Item

AUTO DOOR LOCK

Multi-Information Display

Description

Setting Option

Changes the setting of when to automatically lock the doors.

AUTO DOOR UNLOCK

Changes the setting of when to automatically unlock the driver’s/all the doors.

KEY AND REMOTE UNLOCK MODE PSD KEYLESS OPEN MODE PTG KEYLESS OPEN MODE KEYLESS LOCK ACKNOWLEDGMENT

＊

SECURITY RELOCK TIMER

Changes which doors unlock with the remote transmitter on a first push. Changes the power sliding door opening setting.

Changes the power tailgate opening setting.

The exterior lights flash each time you press the LOCK or UNLOCK button. A beeper will also sound when you press the LOCK button twice. Changes how long it takes (in seconds) for the doors to relock and the security system to set after you unlock but do not open the door. Set/Cancel all the customized settings as default.

DEFAULT ALL (P.96)

＊ ＊

Default setting

1 : 2 : U.S. models only

DRIVER DOOR / ＊ ALL DOORS

＊

＊

SHIFT FROM P WITH VEH SPEED OFF SHIFT TO P IGN OFF OFF DRIVER DOOR ALL DOORS ANY TIME ＊ WHEN UNLOCKED ANY TIME WHEN UNLOCKED ON OFF

＊

＊

＊

90 sec 60 sec 30 sec SET CANCEL

＊

Page 120

122

124

126

128

130

132

96

95

2011 Odyssey10/07/17 09:47:31 31TK8600_101

Multi-Information Display

DEFAULT ALL

If you want to set the default settings, press the INFO ( / ) button to select DEFAULT ALL, then press the SEL/RESET button.

▲ ▼

To set the default settings, press the INFO ( / ) button to select SET then press the SEL/RESET button.

▲ ▼

When DEFAULT ALL is set, you will see the above display for several seconds, then the screen returns to the default all setting display.

96

2011 Odyssey10/07/17 09:47:36 31TK8600_102

Multi-Information Display

If the setting is not successfully completed, ‘‘FAILED’’ is shown for several seconds, and then the screen goes back to the normal message mode. Repeat the same procedure to select DEFAULT ALL.

If you want to cancel DEFAULT ALL, select CANCEL, then press the SEL/RESET button. The screen goes back to the previous display.

97

2011 Odyssey10/07/17 09:47:44 31TK8600_103

Multi-Information Display

Customize Settings You can customize some of the vehicle control settings to your preference. Here are the settings you can customize:

METER SETUP POSITION SETUP LIGHTING SETUP DOOR SETUP

98

Each time you press the INFO ( / ▲