Login- Download PDF Manual
-
phone calls using voice commands, without handling your cell phone.
To use HFL, you need a Bluetooth- compatible cell phone. For a list of compatible phones, pairing procedures, and special feature capabilities:
In the U.S., visit com
or call (888) 528-7876.
handsfreelink.honda.
In Canada, visit (888) 9-HONDA-9.
www.honda.ca,
or call
Bluetooth HandsFreeLink
Using HFL HFLButtons
HFL TALK BUTTON
NAVI VOICE CONTROL BUTTONS
HFL BACK BUTTON
HFL Talk button release to give a command or answer a call.
Press and
−
−
HFL Back button release to end a call, go back to the previous command, or cancel the command.
Press and
CONTINUED
259
2010 Insight ０８／１２／２７ １１：５９：４６ ３１ＴＭ８６００ ０２６５
Press and release the HFL Talk button each time you want to make a command. After the beep, speak in a clear, natural tone.
Try to reduce all background noise. If the microphone picks up voices other than yours, commands may be misinterpreted.
Many commands can be spoken together. For example, you can say ‘‘Call 123-456-7890’’ or ‘‘Dial Peter.’’
When HFL is in use, navigation voice commands cannot be recognized.
To change the volume level of HFL, use the audio system volume knob or the steering wheel volume controls.
Bluetooth HandsFreeLink
VoiceControlTips
MICROPHONE
Air or wind noise from the dashboard and side vents and windows may interfere with the microphone. Adjust or close them as necessary.
260
2010 Insight ０８／１２／２７ １１：５９：５４ ３１ＴＭ８６００ ０２６６
HelpFeatures
To hear general HFL information, including help on pairing a phone or setting up the system, say ‘‘Tutorial.’’
For help at any time, including a list of available commands, say ‘‘Hands free help.’’
Bluetooth HandsFreeLink
InformationDisplay As an incoming call notification, you will see the following display:
Some phones may send battery, signal strength, and roaming status information to HFL.
SIGNAL STRENGTH
BATTERY LEVEL STATUS
HFL MODE
ROAM STATUS
PHONE DIALING
The Bluetooth icon appear on the audio display when a phone is linked.
will also
CONTINUED
261
2010 Insight ０８／１２／２７ １１：５９：５９ ３１ＴＭ８６００ ０２６７
Bluetooth HandsFreeLink
A notification that there is an incoming call, or HFL is in use, will appear on the navigation screen when the audio system is on.
HFL MESSAGE
When there is an incoming call, or HFL is in use, ‘‘HFL’’ will appear at the bottom of the map screen.
262
2010 Insight ０８／１２／２７ １２：００：０７ ３１ＴＭ８６００ ０２６８
Bluetooth HandsFreeLink
How to Use HFL
The ignition switch must be in the ACCESSORY (I) or ON (II) position.
‘‘Pair’’
‘‘Edit’’
Pair a phone to the system (See page 266)
Edit the name of a paired phone (See page 267)
‘‘Phone Setup’’
‘‘Delete’’
Delete a paired phone from the system (See page 267)
Press HFL Talk button
‘‘List’’
‘‘Status’’
‘‘Next Phone’’
Hear a list of all phones paired to the system (See page 267) Hear which paired phone is currently linked to the system (See page 268) Search for another previously paired phone to link to (See page 268)
‘‘Set Pairing Code’’
Set the pairing code to a ‘‘Fixed’’ or ‘‘Random’’ number (See page 268)
‘‘Call’’ or ‘‘Dial’’
‘‘123-555-
’’ ＃＃＃＃
Enter desired phone number (See page 269)
‘‘Jim Smith’’
Once a phonebook entry is stored, you can say a name here. (See page 269)
Press and release the HFL Talk button each time you give a command.
CONTINUED 263
2010 Insight ０８／１２／２７ １２：００：１２ ３１ＴＭ８６００ ０２６９
Bluetooth HandsFreeLink
‘‘Redial’’
‘‘Transfer’’
‘‘Mute’’
‘‘Send’’
Redial the last number called (See page 270)
Transfer a call from HFL to your phone, or from your phone to HFL (See page 272)
Mute your voice to the person at the other end of the call (See page 272)
Send numbers or names during a call (See page 272)
Press HFL Talk button
‘‘Store’’
‘‘Edit’’
Store a phonebook entry (See page 273)
Edit the name of an existing phonebook entry (See page 273)
‘‘Phonebook’’
‘‘Delete’’
Delete a phonebook entry (See page 274)
‘‘Receive Contact’’
‘‘List’’
If your phone supports this function, use this to transfer contacts from your phone to HFL (See page 274)
Hear a list of all stored phonebook entries (See page 274)
Press and release the HFL Talk button each time you give a command.
264
2010 Insight ０８／１２／２７ １２：００：１９ ３１ＴＭ８６００ ０２７０
Bluetooth HandsFreeLink
‘‘System Set up’’
Press HFL Talk button
‘‘Security’’
Apply a security passcode to the system that must be input at each key cycle to access the system (See page 279)
‘‘Change Passcode’’
Change your security passcode (See page 280)
‘‘Call Notification’’
‘‘Auto Transfer’’
Set how you would like to be notified of an incoming call (See page 280)
Set calls to automatically transfer from your phone to HFL when you enter the vehicle (See page 280)
‘‘Clear’’
Clear the system of all paired phones, phonebook entries and security passcode (See page 281)
‘‘Change Language’’
Change language from English to French (See page 282) ＊
‘‘Tutorial’’
Hear a tutorial for general rules on using the system (See page 261)
‘‘Hands Free Help’’
Hear a list of available commands and additional information describing each command (See page 261)
Press and release the HFL Talk button each time you give a command. : Canadian models
＊
CONTINUED 265
2010 Insight ０８／１２／２７ １２：００：３０ ３１ＴＭ８６００ ０２７１
Bluetooth HandsFreeLink
To use HFL, you need to pair your Bluetooth-compatible cell phone to the system.
Phone Setup This command group is available for paired cell phones.
Phonepairingtips
You cannot pair your phone while the vehicle is moving.
Your phone must be in discovery or search mode to pair. Refer to your phone’s manual.
Up to six phones can be paired.
Your phone’s battery may drain faster when it is paired to HFL.
If after three minutes your phone is not ready to pair or a phone is not found, the system will time out and return to idle.
266
Topairacellphone: 1.
Press and release the HFL Talk button. If you are pairing a phone for the first time, HFL will give you information about the pairing process. If it is not the first phone you are pairing, say ‘‘ setup Pair
Phone .’’
’’ and say ‘‘
2.
Follow the HFL prompts and put your phone in discovery or search mode. HFL will give you a 4-digit pairing code and begin searching for your phone.
3.
When your phone finds a Bluetooth device, select HFL from the options and enter the 4-digit code from the previous step.
4.
Follow the HFL prompts and name the newly paired phone.
2010 Insight ０８／１２／２７ １２：００：４１ ３１ＴＭ８６００ ０２７２
Torenameapairedphone: Press and release the HFL Talk button before a command.
Todeleteapairedphone: Press and release the HFL Talk button before a command.
1.
Say ‘‘
Phone setup
.’’
2.
Say ‘‘
Edit
’’ after the prompts.
3.
If there is more than one phone paired to the system, HFL will ask you which phone’s name you want to change. Follow the HFL prompts and rename the phone.
1.
2.
3.
Say ‘‘
Phone setup
.’’
Say ‘‘
Delete
’’ after the prompts.
HFL will ask you which phone you want to delete. Follow the HFL prompts to continue with the deletion.
Bluetooth HandsFreeLink
Tohearthenamesofallpaired phones: Press and release the HFL Talk button before a command.
1.
Say ‘‘
Phone setup
.’’
2.
Say ‘‘
List
’’ after the prompts.
3.
HFL will read out all the paired phone’s names.
CONTINUED
267
2010 Insight ０８／１２／２７ １２：００：５４ ３１ＴＭ８６００ ０２７３
Bluetooth HandsFreeLink
Tohearwhichpairedphoneis currentlylinked: Press and release the HFL Talk button before a command.
Tochangefromthecurrentlylinked phonetoanotherpairedphone: Press and release the HFL Talk button before a command.
1.
2.
3.
Say ‘‘
Phone setup
.’’
Say ‘‘
Status
’’ after the prompts.
HFL will tell you which phone is linked to the system.
1.
2.
3.
4.
Say ‘‘
Phone setup
.’’
Next phone
’’ after the
Say ‘‘ prompts.
HFL disconnects the linked phone and searches for another paired phone.
Once another phone is found, it is linked to the system. HFL will inform you which phone is now linked.
If no other phones are found or paired, HFL will inform you that the original phone is linked again.
268
Tochangethepairingcodesetting: Press and release the HFL Talk button before a command.
1.
2.
3.
Say ‘‘
Phone setup
.’’
Set pairing code
’’ after the
Say ‘‘ prompts.
If you want HFL to create a random code each time you pair a phone, say ‘‘ .’’ If you want to choose your own 4-digit code to be used each time, say ‘‘ and follow the HFL prompts.
Random
Fixed ’’
2010 Insight ０８／１２／２７ １２：０１：０６ ３１ＴＭ８６００ ０２７４
Making a Call You can make calls using any phone number or a name in the HFL phonebook. You can also redial the last number called.
The maximum range between your phone and vehicle is 30 feet (10
meters).During a call, HFL allows you to talk up to 30 minutes after you remove the key from the ignition switch. However, this may weaken the vehicle’s battery.
Bluetooth HandsFreeLink
Tomakeacallusingaphone number: Press and release the HFL Talk button before a command.
Tomakeacallusinganameinthe HFLphonebook: Press and release the HFL Talk button before a command.
1.
Say ‘‘
Call
’’ or ‘‘
Dial
.’’
1.
Say ‘‘
Call
’’ or ‘‘
Dial
.’’
2.
Follow the HFL prompts and say the phone number you want to dial.
3.
Follow the HFL prompts to confirm the number and say Call ‘‘
’’ or ‘‘
Dial
.’’
Once connected, you will hear the person you called through the audio speakers.
2.
3.
Follow the HFL prompts and say the name stored in the HFL phonebook that you want to call.
Follow the HFL prompts to confirm the name and make the call.
CONTINUED
269
2010 Insight ０８／１２／２７ １２：０１：１４ ３１ＴＭ８６００ ０２７５
Bluetooth HandsFreeLink
Toredialthelastnumbercalledby HFL: Press and release the HFL Talk button and say ‘‘
Redial
.’’
Tomakeacallfromanimported phonebook:
1.
Press the INFO button, then select Cellular Phonebook ‘‘
.’’
3.
Select a phonebook you want to choose a phone number from.
Select ‘‘ Phonebook
.’’
Search Imported
If the phonebook you select is PIN- protected, you will need to enter the PIN to access it. See page more information.
277
for
2.
270
2010 Insight ０８／１２／２７ １２：０１：２４ ３１ＴＭ８６００ ０２７６
Bluetooth HandsFreeLink
Receiving a Call When you receive a call, an incoming call notification (if activated) will play and interrupt the audio system if it is on.
Press the HFL Talk button to answer the call, or the HFL Back button to hang up.
CallWaiting If your phone has Call Waiting, press and release the HFL Talk button to put the original call on hold and answer the incoming call.
To return to the original call, press the HFL Talk button again. If you don’t want to answer the incoming call, disregard it and continue with your original call. If you want to hang up the original call and answer the new call, press the HFL Back button.
271
List ICON
To search for a specific name in the phonebook, enter the keyword for either the first or last name.
To display all names in the List phonebook, select the ‘‘
’’ option.
4.
5.
Select the name. All the phone numbers stored for that name will be listed. Select the phone number, and HFL begins dialing.
Store in
If you choose ‘‘ HandsFreeLink number will be stored in HFL, so that you can call it using HFL’s name tag by voice.
,’’ the phone
2010 Insight ０８／１２／２７ １２：０１：３５ ３１ＴＭ８６００ ０２７７
Bluetooth HandsFreeLink
Transferring a Call You can transfer a call from HFL to your phone, or from your phone to HFL.
Muting a Call You can mute your voice to the person you are talking to during a call.
Press and release the HFL Talk button and say ‘‘
Transfer
.’’
To mute your voice during a call, press and release the HFL Talk button and say ‘‘
Mute
.’’
To unmute your voice, press and release the HFL Talk button and say Mute ‘‘
’’ again.
272
Send Numbers or Names During a Call HFL allows you to send numbers or names during a call. This is useful when you call a menu-driven phone system.
Tosendanameornumberduringa call: Press and release the HFL Talk button before a command.
1.
Say ‘‘
Send
.’’
2.
Follow the HFL prompts and say the name or number you want to send.
3.
Follow the HFL prompts to send the tones and continue the call.
To send a pound (
NOTE: ‘‘pound.’’ To send a star (*), say ‘‘star.’’
), say
＃
2010 Insight ０８／１２／２７ １２：０１：５０ ３１ＴＭ８６００ ０２７８
Bluetooth HandsFreeLink
NOTE:
Avoid using duplicate name entries.
Toeditthenumberstoredinaname: Press and release the HFL Talk button before a command.
Avoid using ‘‘home’’ as a name entry.
It is easier for HFL to recognize a multisyllabic or longer name. For example, use ‘‘Peter’’ instead of ‘‘Pete,’’ or ‘‘John Smith’’ instead of ‘‘John.’’
1.
Say ‘‘
Phonebook
.’’
2.
Say ‘‘
Edit
’’ after the prompts.
3.
Follow the HFL prompts and say the name entry you want to edit.
4.
When asked, say the new number for that name.
5.
Follow the HFL prompts to complete the edit.
Phonebook You can store up to 50 names with their associated numbers on HFL. The numbers you store can be not only phone numbers but other types, such as account numbers or passwords, which can be sent during a menu-driven call.
Tostoreaphonebookentry: Press and release the HFL Talk button before a command.
1.
Say ‘‘
Phonebook
.’’
2.
3.
Say ‘‘
Store
’’ after the prompts.
Say a name you want to list as your phonebook entry.
4.
Say the number you want to store for the name entry.
5.
Follow the HFL prompts and say Enter ‘‘
’’ to store the entry.
CONTINUED
273
2010 Insight ０８／１２／２７ １２：０２：０３ ３１ＴＭ８６００ ０２７９
Bluetooth HandsFreeLink
Todeleteaname: Press and release the HFL Talk button before a command.
Tolistallnamesinthephonebook: Press and release the HFL Talk button before a command.
1.
Say ‘‘
Phonebook
.’’
1.
Say ‘‘
Phonebook
.’’
2.
3.
Say ‘‘
Delete
’’ after the prompts.
Say the name you want to delete and follow the HFL prompts to complete the deletion.
2.
Say ‘‘
List
’’ after the prompts.
3.
HFL begins reading the names in the order they were stored.
4.
If you hear a name you want to call, immediately press the HFL Talk button and say ‘‘
Call
.’’
Tostoreaspecificphonenumber fromyourcellphonedirectlytothe HFLphonebook(availableonsome phones): Press and release the HFL Talk button before a command.
1.
Say ‘‘
Phonebook
.’’
2.
3.
4.
Receive contact
Say ‘‘ prompts.
’’ after the
Follow the HFL prompts, select a number from your cell phone, and send it to HFL.
Follow the HFL prompts and name the number, or say Discard ‘‘ you want to store.
’’ if it is not the number
5.
Follow the HFL prompts if you want to store another number.
274
2010 Insight ０８／１２／２７ １２：０２：１６ ３１ＴＭ８６００ ０２８０
Cellular Phonebook Options (availableonsomephones)
Cellular Phonebook
If you select Options from the navigation system menu, you will see four HFL options.
For a list of cell phones that are compatible with this feature:
In the U.S., visit com
or call (888) 528-7876.
handsfreelink.honda.
In Canada, visit (888) 9-HONDA-9.
www.honda.ca,
or call
Bluetooth HandsFreeLink
ImportCellularPhonebook: The entire phonebook data of the cell phone that is linked to HFL can be imported to the navigation system.
SearchImportedPhonebook: Once a phonebook has been imported, you can search the phone numbers by the person’s name.
IMPORTED PHONEBOOK
PIN ICON
IMPORTED DATE
Import Cellular
Select ‘‘ Phonebook ,’’ and HFL will begin importing the phonebook. Select OK ‘‘
’’ after the import is completed.
Search Cellular
Select ‘‘ Phonebook phonebooks will be displayed.
,’’ and a list of imported
Select a phonebook from the list.
CONTINUED
275
2010 Insight ０８／１２／２７ １２：０２：２８ ３１ＴＭ８６００ ０２８１
Bluetooth HandsFreeLink
Select a person from the list. Up to three category icons are displayed in the left side of the list:
Fax
Car
Voice
Other
Preference
Home
Mobile
Work
Pager
These category icons indicate how many numbers are stored for the name. If a name has more than three category icons, ‘‘…’’ is displayed.
Select the person’s number you want to call, and press the HFL Talk button.
If the phonebook is PIN-protected, you will need to enter the 4-digit PIN on the following screen.
To search for a specific name in the phonebook, enter the keyword for either the first or last name.
List ICON
To display all names in the List phonebook, select the ‘‘
’’ option.
276
2010 Insight ０８／１２／２７ １２：０２：３８ ３１ＴＭ８６００ ０２８２
DeleteImportedPhonebook: You can delete any imported phonebook.
After making a selection, the following screen will appear.
PIN Number You can add, change, or remove a PIN number from any phonebook.
Bluetooth HandsFreeLink
Delete Imported
Select ‘‘ Phonebook phonebooks will be displayed.
,’’ and a list of imported
Select a phonebook you want to delete. If the phonebook is PIN- protected, you will need to enter the 4-digit PIN number.
Yes Select ‘‘ the deletion.
,’’ then ‘‘
OK
’’ to complete
ToaddaPIN: If you have selected a phonebook without a PIN, you will see the above display.
Enter the new 4-digit PIN. You will have to re-enter the PIN for confirmation.
CONTINUED
277
2010 Insight PIN number
ToremoveaPIN: Select ‘‘ Do not use PIN ‘‘ the current PIN.
,’’ then select ’’ after you enter
０８／１２／２７ １２：０２：４５ ３１ＴＭ８６００ ０２８３
Bluetooth HandsFreeLink
TochangethePINtoanewnumber:
Select the phonebook you want. The display will change as shown above.
The display will change as shown above.
Enter the current PIN for this phonebook.
Enter the new 4-digit PIN number. You will be asked to re-enter the PIN for verification.
278
2010 Insight ０８／１２／２７ １２：０２：５３ ３１ＴＭ８６００ ０２８４
System Setup This command group allows you to change or customize HFL basic settings.
Toseta4-digitpasscodetolockthe HFLsystemforsecuritypurposes: Press and release the HFL Talk button before a command.
1. 2. 3.
4.
.’’
System setup Security
Say ‘‘ Say ‘‘ ’’after the prompts. Follow the HFL prompts and say the 4-digit passcode you want to set. Follow the HFL prompts to confirm the number.
Bluetooth HandsFreeLink
Once a passcode is set, you NOTE: will need to enter it to use HFL each time you start the vehicle. If you forget the code, your dealer will have to reset it for you, or you will have to clear the entire system (see page 281
).
CONTINUED
279
2010 Insight ０８／１２／２７ １２：０３：０５ ３１ＴＭ８６００ ０２８５
Bluetooth HandsFreeLink
Tochangeyoursecuritypasscode: Press and release the HFL Talk button before a command.
1. 2.
3.
4.
’’ after the
.’’
System setup Change passcode
Say ‘‘ Say ‘‘ prompts. Follow the HFL prompts and say the new 4-digit passcode. Follow the HFL prompts to confirm the number.
Toselecteitheraringtoneora promptastheincomingcall notification : Press and release the HFL Talk button before a command.
＊
1. 2.
3.
’’ after the
System setup .’’ Call notification
Say ‘‘ Say ‘‘ prompts. Follow the HFL prompts and say Ring tone Prompt ‘‘ .’’ You ’’ for no audible can also say ‘‘ incoming call notification.
’’ or ‘‘ Off
＊
The default setting is a ring tone.
280
Toactivateordeactivatetheauto transferfunction: If you get into the vehicle while you are on the phone, the call can be automatically transferred to HFL with the ignition switch in the ACCESSORY (I) position.
Press and release the HFL Talk button before a command.
1. 2.
3.
System setup .’’ Auto transfer ’’ after the
Say ‘‘ Say ‘‘ prompts. HFL will let you know if auto transfer is on or off, depending on the previous setting. Follow the HFL prompts to change the setting.
2010 Insight ０８／１２／２７ １２：０３：１５ ３１ＴＭ８６００ ０２８６
Bluetooth HandsFreeLink
Toclearthesystem: This operation clears the passcodes, paired phones, all names in the HFL phonebook, and all imported phonebook data.
Quick Language Selection Canadianmodelsonly Toquicklychangethelanguage: Press and release the HFL Talk button before a command.
Press and release the HFL Talk button before a command.
1.
Say the language you want to change to in that language.
1.
Say ‘‘
System setup
.’’
2.
Follow the HFL prompts.
2.
Say ‘‘
Clear
’’ after the prompts.
3.
Follow the HFL prompts to continue to complete the clearing procedure.
You can also clear the system when you have forgotten the passcode and cannot access HFL. When HFL asks you for the passcode, say ‘‘ clear the HFL phonebook and all imported phonebook data will be lost.
System .’’ Paired phones, all names in
281
2010 Insight ０８／１２／２７ １２：０３：２４ ３１ＴＭ８６００ ０２８７
Bluetooth HandsFreeLink
Change Language Canadianmodelsonly Tochangethesystemlanguage betweenEnglishandFrench: Press and release the HFL Talk button before a command.
1.
2.
Say ‘‘
Change language
.’’
Follow the HFL prompts to change the language to English or French.
If you have not named your paired phone in the language you just selected, HFL will ask you to name it in the current language.
When French is your currently selected language, you can give voice commands in French.
282
Bluetooth Wireless Technology The Bluetooth name and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Honda Motor Co., Ltd. is under license. Other trademarks and trade names are those of their respective owners.
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
2010 Insight ０８／１２／２７ １２：０３：２８ ３１ＴＭ８６００ ０２８８
Before Driving
Before you begin driving your vehicle, you should know what gasoline to use and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your vehicle, please read the information in this section first.
Break-in Period Fuel Recommendation Service Station Procedures
............................. ................. ......... .................................... .....
Refueling Tighten Fuel Cap Message Opening and Closing the
. 284
. 284
. 285
. 285
. 286Hood
Oil Check Engine Coolant Check
. 287
. 288
. 289
Fuel Economy . 290
Accessories and Modifications . 293
. 295
Carrying Cargo....................................... ................................... ............. ............................... ... .............................
283
2010 Insight ０８／１２／２７ １２：０３：３８ ３１ＴＭ８６００ ０２８９
Break-in Period, Fuel Recommendation
Break-in Period Help assure your vehicle’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period:
Avoid full-throttle starts and rapid acceleration.
Do not change the oil until the scheduled maintenance time.
Avoid hard braking for the first 200 miles (300 km).
You should also follow these recommendations with an overhauled or exchanged engine, or when the brakes are replaced.
Fuel Recommendation Your vehicle is designed to operate on unleaded gasoline with a pump octane number of 87 or higher. Use of a lower octane gasoline can cause a persistent, heavy metallic rapping noise that can lead to engine damage.
We recommend using quality gasolines containing detergent additives that help prevent fuel system and engine deposits.
In addition, in order to maintain good performance, fuel economy, and emissions control, we strongly recommend, in areas where it is available, the use of gasoline that does NOT contain manganese-based fuel additives such as MMT.
Use of gasoline with these additives may adversely affect performance, and cause the malfunction indicator lamp on your instrument panel to come on. If this happens, contact
your authorized dealer for service.
Some gasoline today is blended with oxygenates such as ethanol or MTBE. Your vehicle is designed to operate on oxygenated gasoline containing up to 10% ethanol by volume and up to 15% MTBE by volume. Do not use gasoline containing methanol.
If you notice any undesirable operating symptoms, try another service station or switch to another brand of gasoline.
For further important fuel-related information for your vehicle, or information on gasoline that does not contain MMT, contact your dealer or visit Owner Link at www.hondacars. com.
284
2010 Insight ０８／１２／２７ １２：０３：４７ ３１ＴＭ８６００ ０２９０
Refueling
FUEL FILL DOOR
Push
1.
Park with the driver’s side closest to the service station pump.
2.
Push on the right edge of the fuel fill door and release it so that it pops open. Pull it out to open it fully.
Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel.
Stop the engine, and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately.
HOLDER
FUEL FILL CAP
TETHER
Service Station Procedures
3.
4.
Remove the fuel fill cap slowly. You may hear a hissing sound as pressure inside the tank equalizes. The fuel fill cap is attached to the fuel filler with a tether. Place the cap in the holder on the fuel fill door.
Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to ‘‘top off’’ the tank. This leaves some room in the fuel tank for the fuel to expand with temperature changes.
Ifthefuelnozzlekeepsclickingoff even though the tank is not full, there may be a problem with your vehicle’s fuel vapor recovery system. The system helps keep fuel vapor from going into the atmosphere. Try filling at another pump. If this does not fix the problem, consult your dealer.
CONTINUED
285
2010 Insight ０８／１２／２７ １２：０３：５４ ３１ＴＭ８６００ ０２９１
Service Station Procedures
Tighten Fuel Cap Message
5.
Screw the fuel fill cap back on until it clicks at least once. If you do not properly tighten the cap, you will see a ‘‘TIGHTEN FUEL CAP’’ message on the multi- information display. If the system still detects an evaporative system leak after retightening the cap, the malfunction indicator lamp may come on (see page
403
).
6.
Push the fuel fill door closed until it latches.
Your vehicle’s on board diagnostic system will detect a loose or missing fuel fill cap as an evaporative system leak. The first time a leak is detected a ‘‘TIGHTEN FUEL CAP’’ message appears on the multi-information display.
286
Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen it, then retighten it until it clicks at least once. The message should go off after several days of normal driving once you tighten or replace the fuel fill cap. To scroll to another message, press the INFO button.
The ‘‘TIGHTEN FUEL CAP’’ message will appear each time you restart the engine until the system turns the message off.
2010 Insight ０８／１２／２７ １２：０４：０１ ３１ＴＭ８６００ ０２９２
If the system still detects a leak in the vehicle’s evaporative emissions system, the malfunction indicator lamp (MIL) comes on. If the fuel fill cap was not already tightened, turn the engine off, and check or retighten the fuel fill cap until it clicks at least once. The MIL should go off after several days of normal driving once the cap is tightened or replaced. If the MIL does not go off, have your vehicle inspected by a dealer. For more information, see page
403
Service Station Procedures
Opening and Closing the Hood
HOOD RELEASE HANDLE
LATCH
Pull
1.
Park the vehicle, and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.
2.
Put your fingers under the front edge of the hood near the center. Slide your hand to the left until you feel the hood latch handle. Push this handle to the left to release the hood. Lift up the hood.
If the hood latch handle moves stiffly, or if you can open the hood without lifting the handle, the mechanism should be cleaned and lubricated. CONTINUED
287
2010 Insight ０８／１２／２７ １２：０４：１０ ３１ＴＭ８６００ ０２９３
Service Station Procedures
GRIP
To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. Make sure it is securely latched.
Oil Check
DIPSTICK
SUPPORT ROD
CLIP
3.
Holding the grip, pull the support rod out of its clip. Insert the end into the designated hole in the hood.
288
Wait a few minutes after turning the engine off before you check the oil.
1.
Remove the dipstick (orange loop).
2.
Wipe off the dipstick with a clean cloth or paper towel.
3.
Insert the dipstick all the way back into its hole.
2010 Insight ０８／１２／２７ １２：０４：１７ ３１ＴＭ８６００ ０２９４
Service Station Procedures
UPPER MARK LOWER MARK
4.
Remove the dipstick again, and check the level. It should be between the upper and lower marks.
If it is near or below the lower mark, see 348
Adding Engine Oil
on page
Engine Coolant Check
RESERVE TANK
MAX
MIN
Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines. If Adding it is below the MIN line, see Engine Coolant for 353
information on adding the proper coolant.on page
Owner’s Maintenance on page
Refer to Checks for information about checking other items on your vehicle.
345
289
2010 Insight ０８／１２／２７ １２：０４：２６ ３１ＴＭ８６００ ０２９５
Fuel Economy
Actual Mileage and EPA Fuel Economy Estimates Comparison. Fuel economy is not a fixed number. It varies based on driving conditions, driving habits and vehicle condition. Therefore, it is not possible for one set of estimates to predict fuel economy precisely for all drivers in all environments.
The EPA fuel economy estimates shown in the example to the right are a useful tool for comparison when buying a vehicle. EPA estimates include:
−
City MPG Represents urban driving in light traffic. A range of miles per gallon achieved is also provided.
−
Represents a
Highway MPG mixture of rural and interstate driving, in a warmed-up vehicle, typical of longer trips in free-flowing traffic. A range of miles per gallon
290
City MPG
Highway MPG
Combined Fuel Economy
Estimated Annual Fuel Cost
(Sample U.S. EPA label shown)
achieved is also provided.
−
Combined Fuel Economy Represents a combination of city and highway driving. The scale represents the range of combined fuel economy for other vehicles in the class.
Estimated Annual Fuel Cost − Provides an estimated annual fuel cost, based on 15,000 miles in the U.S. or 20,000 km in Canada per year
multiplied by the cost per gallon (based on EPA fuel cost data) divided by the combined fuel economy.
For more information on fuel economy ratings and factors that affect fuel economy, visit fueleconomy.gov vehicles.gc.ca
www. (Canada: Visit
www.
2010 Insight ０８／１２／２７ １２：０４：３８ ３１ＴＭ８６００ ０２９６
Fuel Economy
Fuel Economy Factors The following factors can lower your vehicle’s fuel economy:
Aggressive driving (hard acceleration and braking) Excessive idling, accelerating and braking in stop-and-go traffic Cold engine operation (engines are more efficient when warmed up) Driving with a heavy load or the air conditioner running Improperly inflated tires
Improving Fuel Economy
VehicleMaintenance A properly maintained vehicle maximizes fuel economy. Poor maintenance can significantly reduce fuel economy. Always maintain your vehicle according to the maintenance messages displayed on the multi- Owner’s information display (see Maintenance Checks on page 345
For example:).
Use the recommended viscosity motor oil, displaying the API Certification Seal (see page 348
).
Maintain proper tire inflation An underinflated tire increases − ‘‘rolling resistance,’’ which reduces fuel economy.
Avoid carrying excess weight in your vehicle It puts a heavier load on the engine, increasing fuel consumption.
−
−
Keep your vehicle clean In particular, a build-up of snow or mud on your vehicle’s underside adds weight and rolling resistance. Frequent cleaning helps your fuel economy.
DriveEfficiently
−
Drive moderately acceleration, abrupt cornering, and hard braking increase fuel consumption.
Rapid
−
Observe the speed limit Aerodynamic drag has a big effect on fuel economy at speeds above 45 mph (75 km/h). Reduce your speed and you reduce the drag. Trailers, car top carriers, roof racks and bike racks are also big contributors to increased drag.
Avoid excessive idling Idling results in 0 miles per gallon (0 kms per liter).
−
Use the ECON ON mode as much as possible.
CONTINUED
291
2010 Insight ０８／１２／２７ １２：０４：４７ ３１ＴＭ８６００ ０２９７
Fuel Economy
CheckingYourFuelEconomy
Miles driven
Gallons of fuel
Miles per Gallon
100
Liter
Kilometers
L per 100 km
1) 2) 3) 4)
Fill the fuel tank until the nozzle automatically clicks off. Reset trip counter to zero. Record the total gallons (liters) needed to refill. Follow one of the simple calculations above.
Minimize the use of the air conditioning system puts an extra load on the engine which makes it use more fuel. Use the fresh-air ventilation when possible.
The A/C
−
Plan and combine trips Combine several short trips into one. A warmed-up engine is more fuel efficient than a cold one.
−
Calculating Fuel Economy
MeasuringTechniques Direct calculation is the recommended source of information about your actual fuel economy. Using frequency of fill-ups or taking fuel gauge readings are NOT accurate measures of fuel economy. Fuel economy may improve over the first several thousand miles.
292
2010 Insight ０８／１２／２７ １２：０４：５６ ３１ＴＭ８６００ ０２９８
Accessories and Modifications
Modifying your vehicle, or installing some non-Honda accessories, can make it unsafe. Before you make any modifications or add any accessories, be sure to read the following information.
Accessories Your dealer has Honda accessories that allow you to personalize your vehicle. These accessories have been designed and approved for your vehicle, and are covered by warranty.
Although non-Honda accessories may fit on your vehicle, they may not meet factory specifications, and could adversely affect your vehicle’s handling and stability.
Improper accessories or modifications can affect your vehicle’s handling, stability, and performance, and cause a crash in which you can be hurt or killed.
Follow all instructions in this owner’s manual regarding accessories and modifications.
When properly installed, cellular phones, alarms, two-way radios, and low-powered audio systems should not interfere with your vehicle’s computer controlled systems, such as your airbags, anti-lock brakes, and tire pressure monitoring system (if equipped).
Before installing any accessory:
Make sure the accessory does not obscure any lights, or interfere with proper vehicle operation or performance.
