2008 Honda Fit Owners Manual

started. It will take several days of normal driving for the vehicle to turn the warning off.

If the system still detects a loose or missing fuel fill cap, the malfunction indicator lamp (MIL) comes on. Turn the engine off, and check or retighten the fuel fill cap until it clicks at least once. The MIL goes out after several days of normal driving once the cap is tightened or replaced. If it does not go out, have your dealer inspect the vehicle. For more information, see page

231

2008 Fit ０７／０６／２８　２０：２５：２８　３１ＳＡＡ６１０　００７４　

Maintenance Minder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.

179

for

Gauges

69

2008 Fit ０７／０６／２８　２０：２５：３５　３１ＳＡＡ６１０　００７５　

Controls Near the Steering Wheel

PADDLE SHIFTER (DOWNSHIFT) ＊ (P.162)

INSTRUMENT PANEL BRIGHTNESS (P.74)

HEADLIGHTS/TURN SIGNAL/ FOG LIGHTS ＊ (P.72)

MIRROR CONTROLS ＊ (P.95)

HOOD RELEASE HANDLE (P.138)

HORN ＊

PADDLE SHIFTER (UPSHIFT) ＊ (P.162)

HAZARD WARNING BUTTON (P.74)

WINDSHIELD WIPERS/WASHERS (P.71)

REAR WINDOW DEFOGGER (P.74)

PASSENGER AIRBAG OFF INDICATOR (P.31)

ACCESSORY POWER SOCKET (P.99)

STEERING WHEEL ADJUSTMENT (P.75)

CRUISE CONTROL BUTTONS ＊ (P.131)

AUXILIARY INPUT JACK ＊ (P.127)

To use the horn, press the center pad of the steering wheel. If equipped.

1: 2 :

＊ ＊ 70

2008 Fit ０７／０６／２８　２０：２５：４６　３１ＳＡＡ６１０　００７６　

Windshield Wipers and Washers

Windshield Wiper

MIST The wipers run at high speed until you release the lever.

−

OFF

−

The wipers are not activated.

Rear Window Wiper and Washer

−

INT few seconds.

The wipers operate every

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

−

Windshield Washers

Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.

1. 2. 3. 4. 5. 6.

MIST OFF INT LO Low speed HI High speed Windshield washers

Intermittent

− − −

Push the right lever up or down to select a position.

1.

OFF When you turn the wiper switch to the ‘‘OFF’’ position, the wiper will return to its parked position.

2.

Rotate the switch clockwise to turn the rear window wiper ON.

CONTINUED

71

2008 Fit ０７／０６／２８　２０：２５：５３　３１ＳＡＡ６１０　００７７　

Windshield Wipers and Washers, Turn Signal and Headlights

3.

4.

Hold past ON to turn the rear window wiper on and to spray the rear window washer.

Rotate the switch counterclockwise to spray the window washer.

The rear window washer uses the same fluid reservoir as the wind- shield washer.

Turn Signal and Headlights

−

Turn Signal Push down on the left lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to the center when you release it or complete a turn.

Turn signal Off Parking and interior lights Headlights High beams Flash high beams

1. 2. 3. 4. 5. 6. OnSportmodel Fog lights off 7. Fog lights on 8.

72

2008 Fit ０７／０６／２８　２０：２６：０２　３１ＳＡＡ６１０　００７８　

−

Turning the switch to

’’ position turns on the

Headlights the ‘‘ parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.

Turning the switch to the ‘‘ position turns on the headlights.

’’

’’ or ‘‘

When the light switch is in the ‘‘ ’’ position, the lights on indicator comes on as a reminder. This indicator stays on if you leave the light switch on and turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position.

If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.

−

Push the lever

High Beams forward and the high beam indicator will come on (see page back to return to low beams.

). Pull it

65

To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

Fog Lights OnSportmodel Turn the fog lights on and off by turning the switch next to the headlight switch.

You can use the fog lights only when the headlights are on low beam. They will go off when the headlights are turned off.

Headlights

position, the high beam

Daytime Running Lights Canadianmodelsonly With the headlight switch off or in the headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.

The headlights revert to normal operation when you turn them on with the switch.

73

2008 Fit ０７／０６／２８　２０：２６：１０　３１ＳＡＡ６１０　００７９　

Instrument Panel Brightness, Hazard Warning Button, Rear Window Defogger

Instrument Panel Brightness

Hazard Warning Button

Rear Window Defogger

INSTRUMENT PANEL BRIGHTNESS CONTROL KNOB

You can change the instrument panel brightness only when the light switch is on. Turn the knob on the upper part of the instrument panel to adjust the brightness.

You will hear a beep when maximum or minimum brightness is reached. You will also hear a beep when the maximum level is canceled by turning the knob a click to the left.

74

Push the button to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. You must manually shut off the rear window defogger when it is no longer needed.

2008 Fit ０７／０６／２８　２０：２６：１９　３１ＳＡＡ６１０　００８０　

Rear Window Defogger, Steering Wheel Adjustment

Make sure the rear window is clear and you have good visibility before starting to drive.

Steering Wheel Adjustment Make any steering wheel adjustment before you start driving.

The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

1.

Push the lever under the steering column all the way down.

2.

Move the steering wheel so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

3.

Push the lever up to lock the steering wheel in position.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up and down.

75

2008 Fit ０７／０６／２８　２０：２６：２７　３１ＳＡＡ６１０　００８１　

Keys and Locks

OnSportmodel

AllmodelsexceptSport

KEY NUMBER TAG

KEYS WITH TRANSMITTER

KEY NUMBER TAG

KEYS

Your vehicle comes with the two ignition keys.

76

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.

These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.

Protect the keys from direct sunlight, high temperature, and high humidity.

Do not drop the keys or set heavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

AllmodelsexceptSport The keys do not contain batteries. Do not try to take them apart.

2008 Fit ０７／０６／２８　２０：２６：３５　３１ＳＡＡ６１０　００８２　

If the system repeatedly does not recognize the coding of your key, contact your dealer.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable.

If you have lost your key and cannot start the engine, contact your dealer.

Always take the ignition key with you whenever you leave the vehicle alone.

The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.

When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on for a few seconds, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.

The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.

Immobilizer System

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

77

2008 Fit ０７／０６／２８　２０：２６：４３　３１ＳＡＡ６１０　００８３　

Ignition Switch

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

You will hear a reminder beeper if you leave the key in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

−

You can

ACCESSORY (I) operate the audio system and the accessory power socket in this position.

−

This is the normal key

ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.

−

Use this position

START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, push it in slightly. If your vehicle has an automatic transmission, the shift lever must also be in park.

78

If your vehicle has an automatic transmission, the shift lever must be in Park before you can remove the key from the ignition switch.

Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control of the vehicle.

Remove the key from the ignition switch only when parked.

2008 Fit ０７／０６／２８　２０：２６：５１　３１ＳＡＡ６１０　００８４　

TAB

UNLOCK

LOCK

Each door has a lock tab on the top of the door. Push in the tab to lock the door, and pull it out to unlock.

AllmodelsexceptSport Each front door can be locked or unlocked with the ignition key.

OnCanadianDXmodel To lock the passenger’s door when getting out of the vehicle, push in the lock tab and close the door. To lock the driver’s door, pull and hold the outside door handle, then push in the lock tab. Release the handle, then close the door.

Door Locks

Power Door Locks

MASTER DOOR LOCK SWITCH

AllmodelsexceptCanadianDX To lock the doors and the tailgate, push the top of the master door lock switch on the driver’s door, push in the lock tab on the driver’s door, or use the key in the outside door lock on the driver’s door.

Pushing the bottom of the master door lock switch unlocks all doors and the tailgate.

CONTINUED

79

2008 Fit ０７／０６／２８　２０：２６：５８　３１ＳＡＡ６１０　００８５　

Door Locks

The lock tab on each passenger’s door locks and unlocks only that door. Pulling up the driver’s lock tab only unlocks the driver’s door. To unlock only the driver’s door from the outside, turn the key and release it. If you turn it again, the remaining doors and the tailgate unlock.

To lock a passenger’s door when getting out of the vehicle, push in the lock tab and close the door. To lock the driver’s door, remove key from ignition switch and push in the lock tab or push the top of the master door lock switch, then close the door.

80

LockoutPrevention With the driver’s door open and the key in the ignition switch, the master door lock switch is disabled. It is not disabled if the driver’s door is closed. If you try to lock the open driver’s door with the key in the ignition switch by pushing in the lock tab, the tabs on all doors pop up when you close the door.

Childproof Door Locks

LEVER

Unlock

Lock

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from inside regardless of the position of the lock tab. To open the door, pull the lock tab up, and use the outside door handle.

2008 Fit ０７／０６／２８　２０：２７：０４　３１ＳＡＡ６１０　００８６　

AllmodelsexceptCanadianDX The tailgate will lock or unlock when you lock or unlock the driver’s door by using the key, the lock tab on the driver’s door, the master door lock switch or the remote transmitter (if equipped).

UNLOCK

LOCK

Tailgate

HANDLE

KEY

AllmodelsexceptSport You can lock or unlock the tailgate with the key.

To open the tailgate, pull the handle, then lift up.

CONTINUED

81

2008 Fit ０７／０６／２８　２０：２７：１２　３１ＳＡＡ６１０　００８７　

Tailgate

Unlocking the Tailgate

Lock

Unlock

OnSportmodel If the power door lock system cannot unlock the tailgate, unlock it manually.

Place a cloth on the edge of the cover, then use a small flat-tipped screwdriver to remove the cover on the back of the tailgate.

Push the release lever to the right as shown.

If you need to unlock the tailgate manually, it means there is a problem with the tailgate. Have the vehicle checked by your dealer.

TAILGATE HANDLE

To close the tailgate, hold the tailgate handle, lower the tailgate, then press down on the back edge.

Keep the tailgate closed at all times while driving to avoid damaging the tailgate and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard 53

on page

82

2008 Fit ０７／０６／２８　２０：２７：１９　３１ＳＡＡ６１０　００８８　

Remote Transmitter

LED

UNLOCK BUTTON

LOCK BUTTON

PANIC BUTTON

−

OnSportmodel LOCK Press this button once to lock all doors and the tailgate. Some exterior lights will flash once. When you push LOCK twice within 5
seconds, the horn will sound to verify that the doors and the tailgate are locked and the security system has set. You cannot lock the doors and the tailgate if any door or the tailgate is not fully closed or the key is in the ignition switch.

−

Press this button once

UNLOCK to unlock the driver’s door. Push it twice to unlock the remaining doors and the tailgate. Some exterior lights will flash twice each time you press the button.

The ceiling light (if the ceiling light switch is in the door activated position) will come on when you press the UNLOCK button. If you do not open any door or the tailgate within 30 seconds, the light fades out. If you relock the doors and the tailgate with the remote transmitter before 30 seconds have elapsed, the light will go off immediately.

If you do not open any door or the tailgate within 30 seconds, they will automatically relock and the security system will set.

−

Press this button for

PANIC about 2 seconds to attract attention: the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position.

CONTINUED

83

2008 Fit ０７／０６／２８　２０：２７：２７　３１ＳＡＡ６１０　００８９　

Remote Transmitter

RemoteTransmitterCare

Avoid dropping or throwing the transmitter.

Protect the transmitter from extreme temperature.

Do not immerse the transmitter in any liquid.

If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.

Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors and the tailgate, replace the battery as soon as possible. Battery type: CR1616

SCREW

To replace the battery:

1.

Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.

84

2008 Fit ０７／０６／２８　２０：２７：３５　３１ＳＡＡ６１０　００９０　

4.

Remove the old battery, and insert a new battery into the back of the cover with the

side facing down.

＋

BATTERY

An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.

5.

Install the parts in reverse order.

TAB

2.

3.

Separate the transmitter by prying its middle seam with your fingernail.

Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.

Remote Transmitter

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

85

2008 Fit ０７／０６／２８　２０：２７：４２　３１ＳＡＡ６１０　００９１　

Seats

−

11 13

Front Seat Adjustments Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.

Make all seat adjustments before you start driving.

86

To adjust the seat forward and backward, pull up on the lever under the seat cushion’s front edge. Move the seat to the desired position, and release the lever. Try to move the seat to make sure it is locked in position.

LEVER

The seat can also be adjusted forward and backward using the lever on the side of the seat-back. Pull out the lever and push it forward, holding the seat-back with your hand. Move the seat to the desired position, and check the seat to make sure it is locked in position.

2008 Fit ０７／０６／２８　２０：２７：５０　３１ＳＡＡ６１０　００９２　

Rear Seat Adjustments

To change the seat-back angle of the front seat, pull up the lever on the outside of the seat bottom.

Once a seat is adjusted correctly, rock it back and forth to make sure it is locked in position.

LEVER

You can adjust the angle of the rear seat-backs separately. To change the seat-back angle, pull up the release lever on the outer side of the seat- back.

Seats

Head Restraints Seepage forimportantsafety informationandawarningabout improperlypositioningheadrestraints.

13

Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from whiplash and other injuries.

CONTINUED

87

2008 Fit ０７／０６／２８　２０：２７：５５　３１ＳＡＡ６１０　００９３　

Seats

RELEASE BUTTON

The head restraints in the rear outer seating positions do not adjust for height. To remove one for cleaning or repair, push the release button, and lift the restraint up.

They are most effective when you adjust them so the center of the back of the occupant’s head rests against the center of the restraint.

FRONT

The front head restraints adjust for height. You need both hands to adjust a restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways, and push the restraint down.

Failure to reinstall the head restraints can result in severe injury during a crash.

Always replace the head restraints before driving.

88

2008 Fit ０７／０６／２８　２０：２８：０３　３１ＳＡＡ６１０　００９４　

Reclining the Front Seats

Seats

SEAT-BACK ANGLE ADJUSTMENT LEVER

SLIDE LEVER

You can recline the seat-backs on the front seats so they are level with the rear seat cushions, making a large cushioned area. To do this:

2.

1.

Recline the rear seat-backs as far backward as possible (see page 87

).

Remove the front head restraints (see page securely.

), and store them

88

CONTINUED

89

REAR CENTER

RELEASE BUTTON

When a passenger is seated in the rear center seating position, make sure the center head restraint is properly positioned.

Make sure the head restraint locks in position when you reinstall it.

2008 Fit ０７／０６／２８　２０：２８：１１　３１ＳＡＡ６１０　００９５　

Folding the Rear Seat Up The left and right rear seat cushions can be lifted up separately to make room for cargo.

Remove any items from the seat before you fold up the seat cushion.

Pull up the rear seat cushion, and fold the seat leg down. Push the seat cushion firmly against the seat-back to lock it.

Seats

3.

4.

Using the slide lever, move the front seat cushions as far forward as possible.

Pull up the seat-back angle adjustment lever, and pivot the seat-back backward until it is level with the rear seat cushion.

Reverse this procedure to return the front seats to the upright position.

When you return the seat-back to its upright position, hold the seat-back to keep it from going up too quickly.

Make sure you install the head restraints and securely lock the seats before driving.

90

2008 Fit ０７／０６／２８　２０：２８：２０　３１ＳＡＡ６１０　００９６　

Folding the Rear Seat Down The rear seat-backs can be folded down for more cargo room.

Each side folds down separately, so you can still carry a passenger in the rear outer seating position.

Remove any items from the seat before folding down the seat-back.

Make sure there are no items on the floor before folding down the seats.

LEG

FLOOR GUIDE

LATCH

To return the seat cushion to its original position, first make sure there are no items on the floor, then pull up the seat leg fully, and push down the seat cushion slowly while holding it with your hands. Set the seat leg in the floor guide. A latch comes out when the leg is set properly.

Seats

LATCH PLATE

When you fold down the driver’s side rear seat, use the latch plate to release the center seat belt from the detachable anchor (see page Allow the seat belt to retract into the holder on the ceiling, and store the buckles in it.

93

).

1.

Move the front seat cushions as far forward as possible.

CONTINUED

91

2008 Fit ０７／０６／２８　２０：２８：２９　３１ＳＡＡ６１０　００９７　

Seats

5.

Move the front seat backward to the desired position. Make sure the seat is locked in place.

To return the seat-back to its upright position, move the front seat forward again, then lift up the seat-back.

Do not put any heavy items on the seat-back when it is folded down.

Make sure that the folded down rear seat does not interfere with the front passenger’s seat-back. This will cause the front passenger’s weight sensors and the front passenger’s seat belt reminder indicator to work improperly (see pages ). Also check the passenger airbag off indicator to assure proper operation of the passenger’s front airbag.

and

31

18

RELEASE LEVER

2.

Make sure the rear outer head restraint is locked in place. If you fold down the driver’s side seat- back, also adjust the rear center head restraint to its lowest position.

3.

Pull up the release lever on the outside of the seat-back.

4.

Fold the seat-back forward.

92

While lifting the seat-back, the seat cushion may come up with it. To secure the seat cushion, see page

91

Make sure the seat-back and seat cushion are locked securely and all rear shoulder belts are positioned in front of the rear seat-backs. In the center seating position of the rear seat, be sure the detachable anchor is latched securely before using the seat belt (see page

93

).

Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have Carrying Cargo to brake hard (See on page

146

).

2008 Fit ０７／０６／２８　２０：２８：３８　３１ＳＡＡ６１０　００９８　

Detachable Anchor The seat belt in the rear center seat is equipped with a detachable anchor.

This allows the center seat belt to be unlatched when the driver’s side rear seat is folded.

LATCH PLATE

Seats

SMALL LATCH PLATE

TRIANGLE MARKS

Using a seat belt with the detachable anchor unlatched increases the chance of serious injury or death in a crash.

Before using the seat belt, make sure the detachable anchor is correctly latched.

SMALL LATCH PLATE

ANCHOR BUCKLE

Pull out the small latch plate and the latch plate from each holding slot in the ceiling, and pull out the seat belt to extend it.

Line up the triangle marks on the small latch plate and anchor buckle when reattaching the belt and buckle.

Tug on the seat belt to verify that the detachable anchor is securely latched. Make sure the seat belt is not twisted.

CONTINUED

93

2008 Fit ０７／０６／２８　２０：２８：４５　３１ＳＡＡ６１０　００９９　

Seats, Power Windows

ANCHOR BUCKLE

Power Windows

LATCH PLATE

DRIVER’S WINDOW SWITCH

To unlatch the detachable anchor, insert the latch plate into the slot on the side of the anchor buckle. Store the detachable anchor and seat belt latch plates in the retractor housing.

MAIN SWITCH

Turn the ignition switch to the ON (II) position to raise or lower any window. To open the window, push the switch down and hold it. Release the switch when you want to stop the window. To close the window, pull back on the switch and hold it.

94

Closing a power window on someone’s hands or fingers can cause serious injury.

Make sure your passengers are away from the windows before closing them.

AUTO − To open the driver’s window fully, push the window switch firmly down to the second detent, and release it. The window will automatically go down all the way. To stop the window, pull back on the window switch briefly.

To close the window, pull back on the switch and hold it.

2008 Fit ０７／０６／２８　２０：２８：５３　３１ＳＡＡ６１０　０１００　

When you push the MAIN switch in, the switch is off, and the passenger windows cannot be raised or lowered. To cancel this feature, push on the switch again to get it to pop out. Keep the MAIN switch off when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally.

Power Windows, Mirrors

Mirrors

AdjustingthePowerMirrors

TAB

SELECTOR SWITCH

Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.

The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.

ADJUSTMENT SWITCH

AllmodelsexceptCanadianDX 1.

Turn the ignition switch to the ON (II) position.

2.

Move the selector switch to L (driver’s side) or R (passenger’s side).

CONTINUED

95

2008 Fit ０７／０６／２８　２０：２９：００　３１ＳＡＡ６１０　０１０１　

Mirrors, Parking Brake

3.

4.

Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down.

When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings.

Parking Brake

PARKING BRAKE LEVER

Driving the vehicle with the parking brake applied can damage the rear brakes and axles. A beeper will sound if the vehicle is driven with the parking brake on.

To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page

60

).

96

2008 Fit ０７／０６／２８　２０：２９：０５　３１ＳＡＡ６１０　０１０２　

Interior Convenience Items

COAT HOOK

FRONT DOOR POCKET

VANITY MIRROR

SUN VISOR

SEAT-BACK POCKET

COIN TRAY

CENTER POCKET

PASSENGER’S TRAY

REAR SIDE POCKET (RIGHT SIDE)

BEVERAGE HOLDERS

ACCESSORY POWER SOCKET

GLOVE BOX

97

2008 Fit ０７／０６／２８　２０：２９：１１　３１ＳＡＡ６１０　０１０３　

Interior Convenience Items

Beverage Holders

Glove Box

Open the glove box by pushing the button. Close it with a firm push.

Be careful when you are using the beverage holders. A spilled liquid that is very hot can scald you or your passengers. Liquid can also spill from the door pocket beverage holders when you open or close the doors. Use only resealable containers in the door pockets.

Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior.

98

An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.

Always keep the glove box closed while driving.

2008 Fit ０７／０６／２８　２０：２９：２２　３１ＳＡＡ６１０　０１０４　

Interior Convenience Items, Interior Lights

Accessory Power Socket This socket is intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10
amps).

Ceiling Light

DOOR ACTIVATED

ON

To use the accessory power socket, pull up the cover. The ignition switch must be in the ACCESSORY (I) or ON (II) position.

It will not power an automotive type cigarette lighter element.

OFF

Sun Visor To use the sun visor, pull it down. When using the sun visor for the side window, remove the support rod from the clip, and swing it out.

The ceiling light has a three-position switch; ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you:

Open any door. Unlock the doors and the tailgate with the key or the remote transmitter (if equipped).

After all doors are closed tightly, the light fades out in about 30 seconds.

The ceiling light (with the switch in the door activated position) comes on when you remove the key from the ignition switch. If you do not open a door, the light fades out in about 30 seconds.

If you leave any door open without the key in the ignition switch, the ceiling light will go off after 3
minutes.

99

2008 Fit ０７／０６／２８　２０：２９：２５　３１ＳＡＡ６１０　０１０５　

100

2008 Fit ０７／０６／２８　２０：２９：３０　３１ＳＡＡ６１０　０１０６　

Features

Vents, Heating, and A/C Playing the AM/FM Radio AM/FM Radio Reception Playing a Disc Disc Player Error Messages Protecting Your Discs Auxiliary Input Jack Radio Theft Protection Setting the Clock Security System Cruise Control

............. .......... ............ ................................. ....... .................. ...................... ................. .......................... ............................ ...............................

. 102
. 107
. 112
.114
. 123
. 124
. 127
. 128
. 129
. 130
. 131

The heating and air conditioning system in your vehicle provides a comfortable driving environment in all weather conditions.

The standard audio system has many features. This section describes those features and how to use them.

Your vehicle has an anti-theft audio system that requires a code number to enable it.

The security system helps to dis- courage vandalism and theft of your vehicle.

101

2008 Fit ０７／０６／２８　２０：２９：３３　３１ＳＡＡ６１０　０１０７　

Vents, Heating, and A/C

AIR CONDITIONING BUTTON

＊

FRESH AIR/RECIRCULATION LEVER

REAR WINDOW DEFOGGER BUTTON

TEMPERATURE CONTROL DIAL

FAN CONTROL DIAL

MODE CONTROL DIAL

U.S. model is shown.

＊ : If equipped 102

2008 Fit ０７／０６／２８　２０：２９：５１　３１ＳＡＡ６１０　０１０８　

Airflow Controls

Fan Control Dial Turn this dial to increase or decrease the fan speed and airflow.

Temperature Control Dial Turning this dial clockwise increases the temperature of the airflow.

Air Conditioning (A/C) Button Ifequipped This button turns the air conditioning on and off. The indicator in the button is on when the A/C is on.

Fresh Air/Recirculation Lever This lever controls the source of the air going into the system. When you slide the lever to the side, air is brought in from outside the vehicle (fresh air mode). When you select the side, air from the vehicle’s interior is sent through the system again (recirculation mode).

The outside air intakes for the heating and cooling system are at the base of the windshield. Keep this area clear of leaves and other debris.

The system should be left in fresh air mode under almost all conditions. Keeping the system in recirculation mode, particularly with the A/C off, can cause the windows to fog up.

Switch to recirculation mode when driving through dusty or smoky conditions, then return to fresh air mode.

Rear Window Defogger Button This button turns the rear window 74
defogger on and off (see page

).

Mode Control Dial Use the mode control dial to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes.

Vents, Heating, and A/C

Air flows from the center and corner vents in the dashboard.

Airflow is divided between the vents in the dashboard and the floor vents.

Air flows from the floor

vents.

Airflow is divided between

the floor vents and defroster vents at the base of the windshield.

Air flows from the defroster vents at the base of the windshield.

When you select the system automatically turns on the A/C (if equipped). You cannot turn the A/C off in this mode.

or

103

2008 Fit ０７／０６／２８　２０：３０：０２　３１ＳＡＡ６１０　０１０９　

Vents, Heating, and A/C

Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then discharges it through vents near the tailgate.

1.

2. 3. 4.

Set the temperature to the lower limit. Make sure the A/C is off. Select Set the fan to the desired speed.

and

Using the Heater The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming from the system.

1. 2. 3.

and

Select Set the fan to the desired speed. Adjust the warmth of the air with the temperature control dial.

Using the A/C Ifequipped Air conditioning places an extra load on the engine. Check the high temperature indicator (see page 63
turn off the A/C until the indicator goes off.

). If the indicator begins to blink,

1.

2.

3. 4.

5.

Turn on the A/C by pressing the button. The indicator in the button comes on when a fan speed is selected. Make sure the temperature is set to maximum cool. Select If the outside air is humid, select recirculation mode. If the outside air is dry, select Set the fan to the desired speed.

104

you can

Iftheinteriorisverywarm, cool it down more rapidly by partially opening the windows, turning on the A/C, and setting the fan to maximum speed in

2008 Fit ０７／０６／２８　２０：３０：１０　３１ＳＡＡ６１０　０１１０　

Vents, Heating, and A/C

Dehumidify the Interior Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry and can prevent the windows from fogging up.

1. 2.

3.

Turn the fan on. If the A/C is off, turn it on (if equipped). Select Adjust the temperature to your preference.

and

This setting is suitable for all driving conditions whenever the outside temperature is above 32°F (0°C).

To Defog and Defrost To remove fog from the inside of the windows:

1.

2. 3.

4.

5.

6.

by sliding the lever. . The system

Set the fan to the desired speed or high for faster defrosting. Select Select automatically turns on the A/C (if equipped). The A/C indicator will not come on if it was previously off. Adjust the temperature so the airflow feels warm. Select rear window. To increase airflow to the windshield, close the corner vents.

to help clear the

or

When you select the system automatically turns on the A/C. This helps to dehumidify the air and to defog the windshield. In either mode, you cannot turn off the A/C. When you switch to another mode, the A/C returns to its original setting, either on or off, as indicated by the A/C indicator.

105

2008 Fit ０７／０６／２８　２０：３０：１７　３１ＳＡＡ６１０　０１１１　

Vents, Heating, and A/C

To Turn Everything Off Turning the fan speed control dial all the way to the left shuts the system off.

Keep the system off for short periods only.

To keep stale air and mustiness from collecting, you should have the fan running at all times.

To Remove Exterior Frost or Ice From the Windows 1.

Set the fan and temperature controls to maximum level. Select . The system automatically turns on the A/C (if equipped). The A/C indicator does not come on if it was previously off. Select

2.

3.

To clear the windows faster, you can close the dashboard corner vents by rotating the wheel below each vent. This sends more warm air to the windshield defroster vents. Once the windshield is clear, select fresh air mode to avoid fogging the windows.

For your safety, make sure you have a clear view through all the windows before driving.

106

2008 Fit ０７／０６／２８　２０：３０：２４　３１ＳＡＡ６１０　０１１２　

Playing the AM/FM Radio

All models except Sport