Playing Discs (EX and EX-L models without navigation system)
You can also eject discs when the ignition switch is off. The disc that was last selected is ejected first.
To Stop Playing a Disc Press the AM, FM, AUX button, or CD/AUX, XM button to switch to the radio or satellite radio (U.S. models), while a disc is playing. Press the CD button again to play the disc.
If you turn the system off while a disc is playing, either with the PWR/ VOL knob or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the disc will begin playing where it left off.
Removing Discs from the In-dash Disc Changer To remove the disc currently in play, press the eject ( ) button. When a disc is removed from a slot, the system automatically begins the load sequence so you can load another disc in that position. If you do not remove the disc from the changer within 10 seconds, the system returns to the previous mode (AM, FM or satellite radio ). The disc will reload into the system and will remain there in a pause mode.
*
To remove a different disc from the changer, first select it with the appropriate preset button. When that disc begins playing, press the eject button. Continue pressing the eject button to remove all the discs from the changer.
*
: On U.S. EX-L model
168
2008 CR- V Table Of ContentsMain Menu07/07/25 14:57:05 31SWA610 0174
Disc Player Error Messages (EX and EX-L models without navigation system)
If you see an error message in the display while playing a disc, find the cause in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For the additional information on damaged discs, see page
214
The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.
Error Message
Cause
Solution
Track/File format not supported
Mechanical Error
UNSUPPORTED
FORMAT BAD DISC
PLEASE CHECK
OWNERS MANUAL
PUSH EJECT
BAD DISC
PLEASE CHECK
Servo Error
OWNERS MANUAL
Current track will be skipped. The next supported track or file plays automatically. Press the eject button and pull out the disc(s). Check the disc for serious damage, signs of deformation, excessive scratches, and/or dirt see page214. Insert the disc again. If the code does not disappear, or the disc(s) cannot be removed, consult your dealer. Do not try to force the disc out of the player.
The ejected disc will not be reloaded automatically.
169
2008 CR- V Table Of ContentsMain Menu07/07/25 14:57:12 31SWA610 0175
Playing the AM/FM Radio (EX-L model with navigation system)
U.S. model
Canadian model
AUTO SELECT ICON
AUTO SELECT ICON
AM ICON
FM1 ICON AM ICON
SOUND ICON
FM1 ICON
FM2 ICON SOUND ICON
FM2
ICON
BACK GROUND ICON
BACK GROUND ICON
AM/FM BUTTON AUDIO BUTTON SCAN BUTTON
TUNE BAR
PRESET BUTTON
TUNE BAR
PRESET BUTTON
AM/FM BUTTON AUDIO BUTTON SCAN BUTTON
170
2008 CR- V Table Of ContentsMain Menu07/07/25 14:57:22 31SWA610 0176
Playing the AM/FM Radio (EX-L model with navigation system)
Voice Control System In addition to the standard audio controls, the audio system in your vehicle can be operated using the voice control system. See the navigation section in your Quick Start Guide for an overview of this system, and the Navigation System Manual for complete details.
To Play the AM/FM Radio The ignition switch must be in the ACCESSORY (I) or ON (II) position. Turn the system on by pushing the power/volume knob or the AM/FM button. Adjust the volume by turning the power/volume knob.
Pushing the AUDIO button will also turn on the system.
You can also operate the audio system without using the control icons on the audio screen. Use the control buttons on the left side of the screen. The status bar appears on
the bottom of the screen each time you operate any of the control buttons. On the navigation screen, you can also see audio information by touching the AUDIO INFO icon on the lower of the screen.
The band and frequency that the radio was last tuned to are displayed. To change bands, press the AM/FM button, or touch the desired band icon (FM1, FM2, AM, XM1 , or XM 2 ). On the FM band, STEREO will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
*
*
*
: On U.S. model
For information on XM radio, see page
176
To Select a Station You can use any of five methods to find radio stations on the selected band: tune, seek, scan, the preset buttons, and auto select.
−
Use the TUNE bar to tune
TUNE the radio to a desired frequency. Press the side of the bar to tune to a higher frequency, and press the
▲
▼
side to tune to a lower
frequency.
or
▲ ▼
Press and hold the side of the TUNE bar until you hear two beeps to change the frequency rapidly. Release the bar when the display reaches the desired frequency.
CONTINUED
171
2008 CR- V Table Of ContentsMain Menu07/07/25 14:57:30 31SWA610 0177
Playing the AM/FM Radio (EX-L model with navigation system)
−
The seek function
SEEK searches up and down from the current frequency to find a station with a strong signal. To activate it, press and hold the side of the TUNE bar until you hear a beep, then release it.
▲ ▼
or
−
SCAN The scan function samples all stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. You will see SCAN in the display. The system will scan for a station with a strong signal. When it finds one, it will stop and play that station for about 10 seconds.
172
If you do nothing, the system will then scan for the next strong station and play it for 10 seconds. When it plays a station you want to listen to, press the SCAN button again.
Each preset button’s frequency is shown on the bottom of the audio display.
−
Each preset button can
Preset store one frequency on AM and two frequencies on FM.
1.
Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each preset button.
2.
Use the tune, seek, or scan function to tune the radio to a desired station.
3.
Pick a preset button, and hold it until you hear a beep.
4.
Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.
2008 CR- V Table Of ContentsMain Menu07/07/25 14:57:35 31SWA610 0178
Playing the AM/FM Radio (EX-L model with navigation system)
− If you are
AUTO SELECT traveling far from home and can no longer receive your preset stations, you can use the auto select feature to find stations in the local area.
Press the AUDIO button to view the audio control icons, then press the AUTO SEL icon. You will see AUTO SEL flashing in the display, and the system goes into scan mode for several seconds. It stores the frequencies of six AM, and twelve FM stations in the preset buttons.
You will see a ‘‘0’’ displayed after pressing a preset button if auto select cannot find a strong station for every preset button.
If you do not like the stations auto select has stored, you can store other frequencies on the preset buttons as previously described.
Toturnoffautoselect, AUTO SEL icon. This restores the presets you originally set.
press the
For information on AM/FM radio
frequencies and reception, see page
211
173
2008 CR- V Table Of ContentsMain Menu07/07/25 14:57:47 31SWA610 0179
Playing the AM/FM Radio (EX-L model with navigation system)
Adjusting the Sound
SPEAKER SETTING
−
Adjusts the side-to-
BALANCE side strength of the sound. To adjust the left/right balance, touch the L or R icon.
−
Adjusts the
SUBWOOFER strength of sound from the subwoofer speaker. To adjust the sound strength, touch
or
on each side of the adjustment
bar.
SOUND ICON
You can adjust the sound on the navigation screen. To adjust the sound, push the AUDIO button, then enter the sound grid by touching the SOUND icon on the display.
174
BASS/TREBLE SETTING
BASS
−
Adjusts the bass.
−
Adjusts the treble. To
TREBLE adjust the treble and bass, touch on each side of the
or
treble or bass adjustment bar. The adjustment bar on the right lower display shows you the current setting. FADER Adjusts the front-to-back strength of the sound. To adjust the front/rear fader, touch the FR or RR icon.
−
The right upper display shows you the current setting of the sound strength coming from each speaker.
−
The SVC mode
SVC (speed-sensitive volume compensation) controls the volume based on vehicle speed. The faster you go, the louder the audio volume becomes. As you slow down, the audio volume decreases. Touch the appropriate icon (Low, Mid, Hi, Off) to select the mode.
2008 CR- V Table Of ContentsMain Menu07/07/25 14:57:54 31SWA610 0180
Playing the AM/FM Radio (EX-L model with navigation system)
ScreenMode You can select the background screen to display the sound level. There are three screen modes: level (the sound level is shown with the vertical bars), spectrum analysis (the sound level appears as ripples of water), and off. Each time you touch the background icon, the display changes.
This function is set to MID as the default setting when the vehicle leaves the factory. If you feel the sound is too loud, choose low. If you feel the sound is too quiet, choose Hi.
You can also select the icon with the joystick. Move it up and down to move the highlighting and scroll through lists. Select the icon, then move the joystick to left or right to change the setting.
The system will return to the audio display about 5 seconds after you stop adjusting a mode.
Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the control panel (see page illuminates when the parking lights are on, even if the radio is turned off.
). The audio system
76
175
2008 CR- V Table Of ContentsMain Menu07/07/25 14:57:59 31SWA610 0181
Playing the XM Satellite Radio (U.S. EX-L model with navigation system)
XM RADIO ICON MODE ICON
JOYSTICK
CATEGORY INDICATOR
POWER/VOLUME KNOB
AM/FM BUTTON
XM RADIO BUTTON
AUDIO BUTTON
SCAN BUTTON
PRESET CHANNEL NUMBER
176
TUNE BAR
PRESET BUTTONS
2008 CR- V Table Of ContentsMain Menu07/07/25 14:58:06 31SWA610 0182
Playing the XM Satellite Radio (U.S. EX-L model with navigation system)
OnU.S.EX-LmodelwithNavigation System Your audio system is capable of receiving XM Satellite Radio anywhere in the United States, except Hawaii and Alaska.
XM is a registered trademark of XM Satellite Radio, Inc.
XM radio receives signals from two satellites to produce clear, high- quality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, XM radio allows you to view channel and category selections in the display. When you press and hold the AUDIO button, the display also shows all XM information.
Operating the XM Radio To listen to XM radio, turn the ignition switch to the ACCESSORY (I) or the ON (II) position. Push the power/volume knob to turn on the audio system, and press the CD/XM button. Adjust the volume by turning the knob. The last channel you listened to will show in the display.
You can also change to the XM radio while you are listening to an FM station, AM station, disc, pc card, etc., by touching the XM1 or XM2 icon on the audio display.
You can also operate the radio using the control buttons on the left side of the screen. The status bar appears on the bottom of the screen each time you press any of the control buttons. On the navigation screen, you can also see the audio information by touching the AUDIO INFO icon on the lower of the screen.
−
To switch between
MODE channel mode and category mode, touch the MODE icon. In channel mode, you can select all of the available channels. In category mode, such as Jazz, Rock, Classical, etc., you can select all of the channels within that category. Each time you touch and release the MODE icon, the display changes between the channel mode and the category mode.
CONTINUED
177
2008 CR- V Table Of ContentsMain Menu07/07/25 14:58:16 31SWA610 0183
Playing the XM Satellite Radio (U.S. EX-L model with navigation system)
TUNE Press the TUNE bar to change channel selections. Press
−
for lower numbered
for higher numbered channels ▼
▲ and channels. In the category mode, you can only select channels within that category.
Press and hold
−
CATEGORY either side of the TUNE bar to select another category.
or
) until you hear a beep
On the audio display, you will see the selected CHANNEL (number), CATEGORY, NAME (artist name), and TITLE (music title).
You may experience periods when XM Radio does not transmit the artist’s name and song title information. If this happens, there is nothing wrong with your system.
178
−
The scan function gives
SCAN you a sampling of all channels while in the channel mode. In the category mode, only the channels within that category are scanned. To activate scan, press the SCAN button. The system plays each channel in numerical order for a few seconds, then selects the next channel. When you hear a channel you want to listen to, press the button again.
−
Preset
You can store up to 12
preset channels using each preset
button or preset icons on the screen.
Each preset button or icon stores
one channel from the XM1 band and
one channel from the XM2 band.
To store a channel:
1.
Press the XM button. Either XM1
or XM2 will show in the display.
2.
Use the tune, seek, or scan function to tune to a desired channel.
In category mode, only channels within that category can be selected. In channel mode, all channels can be selected.
3.
Pick the preset button (icon) you want for that channel. Press and hold the button (icon) until you hear a beep.
2008 CR- V Table Of ContentsMain Menu07/07/25 14:58:26 31SWA610 0184
Playing the XM Satellite Radio (U.S. EX-L model with navigation system)
4.
Repeat steps 2 and 3 to store the first six channels.
5.
Press the XM button again or
touch the other XM icon (XM1 or
XM2) on the audio display. Store
the next six channels using steps 2
and 3.
Once a channel is stored, press and release the proper preset button (icon) to tune to it. Each preset button’s channel is shown on the bottom of the audio display.
XM Radio Display Messages
‘‘LOADING’’ audio or program information.
XM is loading the
−
−
‘‘OFF AIR’’ currently selected is no longer broadcasting.
The channel
−
The encryption
‘‘UPDATING’’ code is being updated. Wait until the encryption code is fully updated. Channels 0 and 1 should still work normally.
−
The signal is
‘‘NO SIGNAL’’ currently too weak. Move the vehicle to an area away from tall buildings, and with an unobstructed view of the southern horizon.
−
The selected channel
‘‘ - - - - ’’ number does not exist or is not part of your subscription.
‘‘NO INFO’’ This channel has no artist or title information at this time.
−
‘‘ANTENNA’’ There is a problem with the XM antenna. Please consult your dealer.
−
CONTINUED
179
2008 CR- V Table Of ContentsMain Menu07/07/25 14:58:31 31SWA610 0185
Playing the XM Satellite Radio (U.S. EX-L model with navigation system)
The XM satellites are in orbit over the equator; therefore, objects south of the vehicle may cause satellite reception interruptions. To help compensate for this, ground-based repeaters are placed in major metropolitan areas.
Satellite signals are more likely to be blocked by tall buildings and mountains the farther north you travel from the equator. Carrying large items on a roof rack can also block the signal.
Signal may be blocked by mountains or large obstacles to the south.
Signal weaker in these areas.
SATELLITE
180
GROUND REPEATER
2008 CR- V Table Of ContentsMain Menu07/07/25 14:58:41 31SWA610 0186
Playing the XM Satellite Radio (U.S. EX-L model with navigation system)
Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions:
Driving on the north side of an east/west mountain road. Driving on the north side of a large commercial truck on an east/west road. Driving in tunnels. Driving on a road beside a vertical wall, steep cliff, or hill to the south of you. Driving on the lower level of a multi-tiered road. Driving on a single lane road alongside dense trees taller than 50 ft. (15 m) to the south of you. Large items carried on a roof rack.
There may be other geographic situations that could affect XM radio reception.
AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
Receiving Satellite Radio Service If your XM Satellite Radio service has expired or you purchased your vehicle from a previous owner, you can listen to a sampling of the broadcasts available on XM Satellite Radio. With the ignition switch in the ACCESSORY (I) or ON (II) position, push the power/volume knob to turn on the audio system and press the XM button. A variety of music types and styles will play.
www.xmradio.com
If you decide to purchase XM Satellite Radio service, contact XM Radio at 1-800-852-9696. You will need to give them your radio I.D. number and your credit card number. To get your radio I.D. number, press the TUNE
, or at
bar until ‘‘0’’ appears in the display. Your I.D. will appear in the display.
After you’ve registered with XM Radio, keep your audio system in the satellite radio mode while you wait for activation. This should take about 30 minutes.
While waiting for activation, make sure your vehicle remains in an open area with good reception. Once your audio system is activated, you’ll be able to listen to XM radio broadcasts. XM Radio will continue to send an activation signal to your vehicle for at least 12 hours from the activation request. If the service has not been activated after 36 hours, contact XM Radio.
181
2008 CR- V Table Of ContentsMain Menu07/07/25 14:58:46 31SWA610 0187
Playing a disc (EX-L model with navigation system)
CD ICON
JOYSTICK
RANDOM BUTTON
FAST FORWARD BUTTON
SKIP BUTTON
+
REPEAT BUTTON
REWIND BUTTON
SKIP BUTTON
−
U.S. model is shown
POWER/VOLUME KNOB
OPEN BUTTON
CD BUTTON
AUDIO BUTTON
SCAN BUTTON
TUNE BAR
182
2008 CR- V Table Of ContentsMain Menu07/07/25 14:59:00 31SWA610 0188
Playing a disc (EX-L model with navigation system)
To Play a Disc (In-dash single player) You operate the in-dash disc player with the same controls used for the radio. To load or play discs, the ignition switch must be in the ACCESSORY (I) or ON (II) position.
Your vehicle also has the CD
changer and operate at with the
same in-dash disc player. (see page
191
Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.
This audio system can also play CD-
Rs and CD-RWs compressed in MP3
or WMA formats. When playing a
disc in MP3, you will see ‘‘MP3’’ on
the screen. In WMA format, ‘‘WMA’’
will appear on the screen. You can
select up to 255 folders and play up
to 999 tracks. If the disc has a complex structure, it takes a while to read the disc before the system begins to play it.
Video CDs and DVD discs do not work in this unit.
The specifications for compatible MP3 files are: −
Sampling frequency: 32/44.1/48 kHz (MPEG1) 24/22.05/16 kHz (MPEG2) Bit rate: 32/40/48/56/64/80/96/112/128/ 160/192/224/256/320 kbps (MPEG1) 8/16/24/32/40/48/56/64/80/96/ 112/128/160 kbps (MPEG2) Compatible with variable bit rate and multi-session Maximum layers (including ROOT): 8 layers
−
−
−
The specifications for compatible WMA files are: −
Sampling frequency:
32/44.1/48 kHz
Bit rate:
32/40/48/64/80/96/128/160/192
kbps
Compatible with variable bit rate
and multi-session
Maximum layers
(including ROOT): 8 layers
−
−
−
NOTE: If a file on an MP3 or WMA disc is protected by digital rights management (DRM), the audio unit displays CD FORMAT, and then skips to the next file.
183
2008 CR- V Table Of ContentsMain Menu07/07/25 14:59:08 31SWA610 0189
Playing a disc (EX-L model with navigation system)
ToLoadaDisc
DISC SLOT
OPEN BUTTON The in-dash disc player is behind the navigation screen. To use the disc player, press the OPEN button beside the screen. The screen folds back, and the disc slot appears.
Insert a disc about halfway into the disc slot. The drive will pull the disc in the rest of the way and begin to play it.
You cannot load and play 3-inch (8-cm) discs in this system.
CLOSE BUTTON To return the screen to the upright position, press the CLOSE button on the edge of the screen panel. Do not use the folded screen as a tray. If you put a cup, for example, on the screen, the liquid inside the cup may spill on the screen when you go over a bump.
184
2008 CR- V Table Of ContentsMain Menu07/07/25 14:59:17 31SWA610 0190
Playing a disc (EX-L model with navigation system)
Push the AUDIO button beside the screen to show the audio display and operate the disc player.
ToChangeorSelectTracks/Files
PRESET BUTTON’S FUNCTION
You can also operate the audio system without using the control icons on the audio screen. Press the CD button. The status bar appears on the bottom of the screen. On the navigation screen, you can see the audio information whenever you touch the AUDIO INFO icon on the lower portion of the screen.
When playing a CD recorded with text data, the track, album, and artist name are shown on the audio display. When playing a disc in MP3 or WMA, the folder number and name, the file number and name, the artist name, and the elapsed time are shown. The system will continuously play a disc until you change modes. If the disc was not recorded with text data, it will not be displayed.
PRESET BUTTONS
U.S. model is shown You can use the preset buttons while a disc is playing to select passages and change tracks (files in MP3 or WMA mode). Each preset button’s function is shown on the bottom of the screen.
You can also select an icon with the joystick. Move it to left, right, up, or down to change the highlighting and scroll through lists. Then press the ENT on the top of the joystick to select the icon.
−
Each time you press and (preset 6), the player
SKIP release skips forward to the beginning of the next track (file in MP3 or WMA mode). Press and release
(preset 5), to skip backward to
the beginning of the current track. Press it again to skip to the beginning of the previous track.
FF/REW a track/file, press and hold
To move rapidly within
−
(preset 4) or
(preset 3).
CONTINUED
185
2008 CR- V Table Of ContentsMain Menu07/07/25 14:59:24 31SWA610 0191
Playing a disc (EX-L model with navigation system)
−
To
InMP3orWMAmode FOLDER SELECTION select a different folder, press either side of the TUNE bar to move to the beginning of the next folder. Press the side of the TUNE bar to skip to the next folder, and the side to move to the beginning of the current folder. Press it again to skip to the beginning of the previous folder.
▼
▲
−
TRACK REPEAT (FILE REPEAT) To continuously replay a track (file in MP3 or WMA mode), press and release the RPT button (preset 1). You will see TRACK REPEAT in the display. Press the RPT button again to turn it off.
186
This feature,
−
InMP3orWMAmode FOLDER REPEAT when activated, replays all files on the selected folder in the order they are compressed. To activate folder repeat, press and hold the RPT button (preset 1) for 2 seconds. You will see FOLDER REPEAT in the display. The system continuously replays the current folder. Press the RPT button again to turn it off. Selecting a different folder with the TUNE bar also turns off folder repeat.
−
TRACK RANDOM (Random within a disc/folder) This feature plays the tracks/files within a disc in random order. To activate track random, press and release the RDM button (preset 2). You will see TRACK RANDOM in the display. Press the RDM button again to return to normal play.
−
This
InMP3orWMAmode FOLDER RANDOM feature, when activated, plays all files in the selected folder in random order, rather than in the order they are compressed. To activate folder random, press and hold the RDM button. You will see FOLDER RANDOM in the display. The system then selects and plays files randomly. This continues until you deactivate folder random by pressing the RDM button again, or if you select a different folder with the TUNE bar.
2008 CR- V Table Of ContentsMain Menu07/07/25 14:59:32 31SWA610 0192
−
SCAN (TRACK/FILE SCAN) The scan function samples all tracks (files in MP3 or WMA) in the order they were recorded. To activate scan, press and release the SCAN button. You will see TRACK SCAN in the display. You will get a 10 second sampling of each track/file on the disc. Press the SCAN button to get out of scan mode and play the last track/file sampled.
Pressing either SKIP button (preset 5 or 6) also turns off scan.
Playing a disc (EX-L model with navigation system)
This feature,
InMP3orWMAmode
FOLDER SCAN
−
when activated, samples all the first
files in each folder on the disc in
order. To activate folder scan, press
and hold the SCAN button for 2
seconds. You will see FOLDER
SCAN in the display.
The system plays the first file in each folder for about 10 seconds. If you do nothing, the system then plays the first file in each folder for 10 seconds each. After playing the first file of the last folder, the system goes to normal playing.
Pressing either SKIP button (preset 5 or 6), or selecting a different folder with the TUNE bar, or pressing the SCAN button, also turns off folder scan.
UsingaTrackList
FOLDER ICON
TRACK/FILE ICON
FOLDER NUMBER
RETURN ICON
You can also select a track/file directly from a track list on the audio display. Press the AUDIO button to show the audio display, then touch the Track List icon. The track list menu appears on the display.
CONTINUED
187
2008 CR- V Table Of ContentsMain Menu07/07/25 14:59:38 31SWA610 0193
Playing a disc (EX-L model with navigation system)
When playing a CD recorded with text data, each track name is shown on the audio display. With a disc recorded in MP3 or WMA, the folder number and the location are also displayed.
If the disc was not recorded with text data, only the track number is shown.
Select the desired track/file by touching the icon on the display. The selected icon will be highlighted in blue. The system begins to play the selected track/file. With a disc in MP3 or WMA, touch the folder icon on the upper left of the screen to move to the parent folder. The current folder is highlighted in blue.
or
▲ ▼
To scroll through the display, touch the icon on the side of the screen. To go back to the previous display, touch the Return icon on the screen.
188
*
*
To Stop Playing a Disc To play the radio when a disc is playing, press the AM/FM button or touch the FM1, FM2, AM, XM1 , or XM2 icon. If a PC card is in the audio unit, touch the CARD icon to play the PC card. If a CD or CDs are loaded in the CD changer, touch the CDC icon to play the CD changer. Press the CD button again or touch the CD icon to switch back to the disc player.
If you turn the system off while a disc is playing, either with the power/volume knob or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the disc will begin playing where it left off.
*
: U.S. model only
2008 CR- V Table Of ContentsMain Menu07/07/25 14:59:44 31SWA610 0194
Playing a disc (EX-L model with navigation system)
Protecting Discs For information on how to handle and protect discs, see page
213
184
RemovingaDisc To remove a disc from the audio unit, fold back the screen by pressing the ). Press OPEN button (see page the disc eject button ( ) to remove the disc. If you eject the disc, but do not remove it from the slot, the system will automatically reload it after 10 seconds and put it in pause mode. To begin playing, press the CD button.
To return the screen to the upright position, press the CLOSE button.
You cannot close the screen if a disc is partially inserted into its slot.
You can also eject the disc when the ignition switch is off.
189
2008 CR- V Table Of ContentsMain Menu07/07/25 14:59:52 31SWA610 0195
Disc Player Error Messages (EX-L model with navigation system)
Error Message
Cause
Solution
DISC ERROR
FOCUS Error
MECH ERROR
Mechanical Error
DISC
TOC Error
HEAT ERROR
High Temperature
Press the eject button, and pull out the disc. Check if it is inserted correctly in the disc player. Make sure the disc is not scratched or damaged. For more information see page 214 . Press the eject button, and pull out the disc. Check the disc for damage or deformation. For more information see page 214 . If the disc cannot be pulled out, or the error message does not disappear after the disc is ejected, see your dealer. Press the eject button, and pull out the disc. Check the disc for damage or deformation. Will disappear when the temperature returns to normal.
If you see an error message in the display while playing a disc, find the cause in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For the additional information on damaged discs, see page
214
The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.
190
2008 CR- V Table Of ContentsMain Menu07/07/25 14:59:59 31SWA610 0196
CD Changer (EX-L model with navigation system)
U.S. model
Canadian model
POWER/VOLUME KNOB
CD ICON
CD CHANGER ICON
POWER/VOLUME KNOB
CD ICON
CD CHANGER ICON
JOYSTICK
JOYSTICK
OPEN BUTTON
CD BUTTON AUDIO BUTTON
SCAN BUTTON
TUNE BAR
RANDOM BUTTON
OPEN BUTTON
CD BUTTON AUDIO BUTTON
SCAN BUTTON
TUNE BAR
RANDOM BUTTON
+
SKIP BUTTON −
SKIP BUTTON
+
SKIP BUTTON −
SKIP BUTTON
REPEAT BUTTON
FAST FORWARD BUTTON
REPEAT BUTTON
FAST FORWARD BUTTON
REWIND BUTTON
REWIND BUTTON
191
2008 CR- V Table Of ContentsMain Menu07/07/25 15:00:06 31SWA610 0197
CD Changer (EX-L model with navigation system)
Loading CDs in the Changer Your vehicle has the CD changer in the center console.
CD-R, CD-RW disc, and CD compressed in MP3 and WMA will not work in this unit. Video CDs and DVD discs also will not work.
Do not spill any liquids on the center console. Spilled liquids can damage electrical components in the CD changer.
192
1.
Open the center console cover, then slide open the CD changer cover by pulling it rearward.
2.
Push the EJECT button to remove the CD magazine. The magazine will pop up automatically.
EJECT BUTTON
2008 CR- V Table Of ContentsMain Menu07/07/25 15:00:13 31SWA610 0198
CD Changer (EX-L model with navigation system)
4.
Put a CD on the tray with the printed surface facing up as shown.
5.
Reinstall the tray in the magazine. Repeat this procedure to open the other five trays.
3.
To install a CD into the magazine, push the button while pulling out on the tab.
6.
Store all six trays in the magazine, and reinstall the magazine in the CD changer as shown.
7.
Make sure to slide the CD changer cover closed until it clicks.
To remove CDs from the CD changer, refer to the loading procedure.
193
2008 CR- V Table Of ContentsMain Menu07/07/25 15:00:21 31SWA610 0199
CD Changer (EX-L model with navigation system)
To select a different disc, use the preset buttons (5 or 6). Press and release the Preset 5 (DISC ) − button to select the previous disc or Preset 6 (DISC ) to select the next disc in sequence. Pressing the or side of the TUNE bar also ▼ changes the disc. If you select an empty position in the CD changer, the system will try to load the CD in the next available slot.
+
▲
TUNE BAR
PRESET BUTTONS
You can use the preset buttons while a disc is playing to select passages and change tracks. Each preset button function is shown on the bottom of the screen.
To Play a CD To play CDs, the ignition switch must be in the ACCESSORY (I) or ON (II) position.
You operate the CD changer with the same controls used for the in- dash disc player or the radio. To select the CD changer, touch the CDC icon. The disc and track numbers are displayed. The system will continuously play a CD until you change modes.
Do not use CDs with adhesive labels. The label can curl up and cause the CD to jam in the unit.
194
2008 CR- V Table Of ContentsMain Menu07/07/25 15:00:28 31SWA610 0200
CD Changer (EX-L model with navigation system)
−
button
Push the
SKIP (preset 6) to play the next track on the disc. Push the (preset 5) once to replay the track in play; press it twice to replay the previous track.
button
−
To move more rapidly
FF/REW within a track, press and hold the (preset 3)
(preset 4) or
button.
−
REPEAT (Track Repeat) To continuously replay a track, press and release the RPT button (preset 1). You will see TRACK REPEAT in the display. Press the RPT button again to turn it off.
−
To continuously
DISC REPEAT replay the current CD, press and hold the RPT button (preset 1) until you see the DISC REPEAT in the display. Press it again to turn it off.
−
RANDOM (Track Random) Press and release the RDM button (preset 2) to play the tracks in random order. You will see TRACK RANDOM in the display. Press the RDM button again to return to normal play.
−
Press and hold the
DISC SCAN SCAN button to get a 10 second sampling of the first song of each disc in the CD changer. You will see DISC SCAN in the display. Press and hold the button again to turn it off.
−
To play all
DISC RANDOM tracks in each CD in random order, press and hold the RDM button (preset 2) until you see DISC RANDOM in the display. Press the RDM button again to return to normal play.
−
The SCAN
SCAN (Track Scan) function samples all the tracks on the selected disc in the order they are recorded. To activate it, press and release the SCAN button. You will see TRACK SCAN in the display, and you will get a 10 second sampling of each track on the selected CD. Press the SCAN button again to get out of scan mode.
195
2008 CR- V Table Of ContentsMain Menu07/07/25 15:00:34 31SWA610 0201
CD Changer (EX-L model with navigation system)
To Stop Playing a CD Press the AM/FM or CD/XM button to switch to the radio or satellite radio while a CD is playing.
*
If there is a PC card in the audio unit, touch the CARD icon to switch to the PC card while a CD is playing.
Touch the CDC icon again to play the CD in the CD changer.
If you turn the system off while a CD in the CD changer is playing, the CD will stay in the drive. When you turn the system back on, the CD will be in pause mode. Touch the CDC icon on the audio screen. The CD will begin playing where it left off.
*
: On U.S. model only
196
2008 CR- V Table Of ContentsMain Menu07/07/25 15:00:41 31SWA610 0202
CD Changer Error Messages (EX-L model with navigation system)
If you see an error message in the display while playing a disc, find the cause in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For the additional information on damaged discs, see page
214
Error Message
Cause
Solution
DISC ERROR
FOCUS Error
MECH ERROR
Mechanical Error
The disc is pulled out. Check if it is inserted correctly in the disc player. Make sure the disc is not scratched or damaged. For more information see page 214 . Press the eject button, and pull out the disc. Check the disc for damage or deformation. For more information see page 214 . If the disc cannot be pulled out, or the error message does not disappear after the disc is ejected, see your dealer.
The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.
197
2008 CR- V Table Of ContentsMain Menu07/07/25 15:00:49 31SWA610 0203
Playing a PC card (EX-L model with navigation system)
U.S. model
Canadian model
TRACK LIST ICON
TRACK LIST ICON
POWER/VOLUME KNOB
PC CARD ICON JOYSTICK
POWER/VOLUME KNOB
PC CARD ICON
JOYSTICK
OPEN BUTTON CD/XM BUTTON AUDIO BUTTON SCAN BUTTON TUNE BAR
PLAY MODE ICON
OPEN BUTTON CD/AUX BUTTON
AUDIO BUTTON
SCAN BUTTON TUNE BAR
PLAY MODE ICON
REPEAT BUTTON
RANDOM BUTTON
−
SKIP BUTTON
FAST FORWARD BUTTON
+
SKIP BUTTON
REPEAT BUTTON
RANDOM BUTTON
−
SKIP BUTTON
FAST FORWARD BUTTON
+
SKIP BUTTON
REWIND BUTTON
REWIND BUTTON
198
2008 CR- V Table Of ContentsMain Menu07/07/25 15:01:03 31SWA610 0204
Playing a PC card (EX-L model with navigation system)
To Play a PC Card You operate the PC card player with the same controls used for the radio and the disc player. To load or play a card, the ignition switch must be in the ACCESSORY (I) or ON (II) position.
The PC card player reads and plays
cards in MP3 or WMA formats.
Depending on the format, the screen
will indicate ‘‘MP3’’ or ‘‘WMA’’ when
a card is playing. The card limit of
the player is 255 folders and 999
tracks. If the card has a complex
structure, it takes some time for the
system to begin playing it.
Based on PCMCIA 2.1/JEIDA 4.2, the recommended PC cards for the PC card reader are:
CompactFlash Flash ATA SD memory card
Always use the recommended memory card with the appropriate adapter (if an adapter is needed). Some memory cards will not work in this unit.
NOTE:
When you insert a PC card into the slot, make sure you put it in straight. If you cannot insert it, remove it, and insert again.
Do not keep PC cards in the vehicle. Direct sunlight and high heat will damage them.
To avoid damaging the card reader, do not insert hard disc drive cards into the PC card slot.
You cannot close the screen (move it to the upright position) until the PC card is inserted all the way into its slot or removed.
Never insert foreign objects into the PC card slot.
−
The specifications for compatible MP3 files are: −
Sampling frequency:
32/44.1/48 kHz (MPEG1)
24/22.05/16 kHz (MPEG2)
Bit rate: 32/40/48/56/64/80/96/
112/128/160/192/224/256/320
kbps (MPEG1)
8/16/24/32/40/48/56/64/80/96/
112/128/160 kbps (MPEG2)
Compatible with variable bit rate
and multi-session
Maximum layers
(including ROOT): 8 layers
−
−
CONTINUED
199
2008 CR- V Table Of ContentsMain Menu07/07/25 15:01:13 31SWA610 0205
Playing a PC card (EX-L model with navigation system)
LoadingaPCCard
PC CARD SLOT
−
The specifications for compatible WMA files are: −
Sampling frequency: 32/44.1/48 kHz Bit rate: 48/64/80/96/128/160/192 kbps Compatible with variable bit rate and multi-session Maximum layers (including ROOT): 8 layers
−
−
In WMA format, DRM (digital rights management) files cannot be played. If the system finds a DRM file, it skips that file and plays the next available folder or file.
The PC card slot is behind the navigation screen. To use the PC card player, press the OPEN button beside the screen. The screen folds back, and the PC card slot appears.
200
Insert a PC card straight into the slot. The drive will read the PC card and begin to play it.
Return the screen to the upright position by pressing the CLOSE button on the edge of the screen panel.
Push the AUDIO button beside the screen to show the audio display and operate the PC card player.
You can also operate the audio system without using the control icons on the audio screen. Press any of the appropriate control buttons. The status bar appears on the bottom of the screen. On the navigation screen, you can see the audio information whenever you touch the AUDIO INFO icon on the screen.
2008 CR- V Table Of ContentsMain Menu07/07/25 15:01:24 31SWA610 0206
There are three play modes: Folder, Artist, and Album. Touch the PLAY MODE icon, then choose one of the modes by touching its icon. When a mode is selected, it is highlighted in blue.
Folder mode plays tracks in the order they were added to the card.
Artist mode plays tracks in alphabetical order, by artist and song title.
Album mode plays albums (folders) in alphabetical order.
If play mode information was not included in the tracks/files when they were added to the card, it will not be displayed on the screen.
Playing a PC card (EX-L model with navigation system)
ToSelectaPlayMode
FOLDER MODE
PLAY MODE ICON
MODE INDICATOR
ARTIST MODE
PLAY MODE ICON
ALBUM MODE
PLAY MODE ICON
U.S. model is shown
MODE INDICATOR
MODE INDICATOR
CONTINUED
201
2008 CR- V Table Of ContentsMain Menu07/07/25 15:01:30 31SWA610 0207
Playing a PC card (EX-L model with navigation system)
PLAY MODE ICON
U.S. EX-L model is shown
To select a play mode, push the AUDIO button to show the audio display, then touch the PLAY MODE icon on the display.
Select the desired mode by touching the appropriate icon, or move the joystick, then press the ENT.
After you select the play mode, the display changes to the selectable playing menu. If you select ‘‘Continue playing the Current Song,’’ the system goes into the selected play mode after playing the current file.
202
2008 CR- V Table Of ContentsMain Menu07/07/25 15:01:38 31SWA610 0208
If you select ‘‘Play a New Track List,’’ the system goes into the selected play mode immediately and begins to play the new track list.
To go back to the previous screen, press the CANCEL button on the right side of the screen. To exit the play mode screens, press the AUDIO button.
Playing a PC card (EX-L model with navigation system)
ToChangeorSelectTracks/Files
PRESET BUTTON’S FUNCTION
Icons on the screen can also be selected with the joystick. Move the joystick left or right and up or down until the icon is highlighted, then press the ENT on the top of the joystick to select the icon.
PRESET BUTTONS
U.S. model is shown
You can use the preset buttons while a card is playing to select or change files. Each preset button’s function is shown on the bottom of the screen.
CONTINUED
203
2008 CR- V Table Of ContentsMain Menu07/07/25 15:01:44 31SWA610 0209
Playing a PC card (EX-L model with navigation system)
−
Each time you press and (preset 6), the player
SKIP release skips forward to the beginning of the next file. Press and release
(preset 5), to skip backward to
the beginning of the current file. Press it again to skip to the beginning of the previous file.
−
FF/REW a file, press and hold or