2008 Honda CR V Owners Manual

(P.63)

DAYTIME RUNNING LIGHTS INDICATOR ANTI-LOCK BRAKE SYSTEM INDICATOR VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR (P.62)

(P.61)

SEAT BELT REMINDER INDICATOR (P.60)

SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P.61) SIDE AIRBAG OFF INDICATOR (P.61)

＊

LOW TIRE PRESSURE INDICATOR (P.64)

59

＊ The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４２：０１　３１ＳＷＡ６１０　００６５　

Instrument Panel Indicators

The instrument panel has many indicators that give you important information about your vehicle.

Malfunction Indicator Lamp 325

See page

Low Oil Pressure Indicator

The engine can be severely damaged if this indicator flashes or stays on when the engine is running. For more information, see page 324

Charging System Indicator

If this indicator comes on when the engine is running, the battery is not being charged. For more information, see page

324

60

U.S.

Canada

Parking Brake and Brake System Indicator

This indicator has two functions:

1.

2.

It comes on when you turn the ignition switch to the ON (II) position. It is a reminder to check the parking brake. A beeper sounds if you drive with the parking brake not fully released. Driving with the parking brake not fully released can damage the brakes and tires.

If it stays on after you have fully released the parking brake while the engine is running, or if it comes on while driving, there could be a problem with the brake system. For more information, see page

326

Seat Belt Reminder Indicator

This indicator comes on when you turn the ignition switch to the ON (II) position. It reminds you and your passengers to fasten your seat belts. A beeper also sounds if you have not fastened your seat belt.

If you turn the ignition switch to the ON (II) position before fastening your seat belt, the beeper sounds, and the indicator flashes. If you do not fasten your seat belt before the beeper stops, the indicator stops flashing but remains on.

If your front passenger does not fasten their seat belt, the indicator comes on about 6 seconds after the ignition switch is turned to the ON (II) position.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４２：１１　３１ＳＷＡ６１０　００６６　

Instrument Panel Indicators

If either of you do not fasten your seat belt while driving, the beeper will sound and the indicator will flash again at regular intervals. For more information, see page

18

Supplemental Restraint System Indicator

This indicator comes on briefly when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates a potential problem with your front airbags. This indicator will also alert you to a potential problem with your side airbags, passenger’s side airbag cutoff system, side curtain airbags, automatic seat belt tensioners, driver’s seat position sensor, or the front passenger’s weight sensors. For more information, see page 31

U.S.

Canada

Side Airbag Off Indicator

This indicator comes on briefly when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. For more information, see page

31

Immobilizer System Indicator

This indicator comes on briefly when you turn the ignition switch to the ON (II) position. It will then go off if you have inserted a properly-coded ignition key. If it is not a properly- coded key, the indicator will blink, and the engine’s fuel system will be disabled (see page

80

).

Anti-lock Brake System (ABS) Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position. If it comes on at any other time, there is a problem in the ABS. If this happens, have your vehicle checked by your dealer. With the indicator on, your vehicle still has normal braking ability but no anti- lock. For more information, see page 254

61

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４２：２２　３１ＳＷＡ６１０　００６７　

Instrument Panel Indicators

Vehicle Stability Assist (VSA) System Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position.

If it comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the VSA system. Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. See page for more information on the 256
VSA system.

62

VSA Activation Indicator

Cruise Control Indicator

This indicator comes on when you set the cruise control. See page 222
cruise control.

for information on operating the

Cruise Main Indicator

This indicator comes on when you turn on the cruise control system by pressing the CRUISE button (see page

222

).

This indicator has three functions:

1.

2.

3.

It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.

It flashes when VSA is active (see page

256

).

It comes on along with the VSA system indicator if there is a problem with the VSA system.

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position. See page for more information on the VSA system.

256

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４２：３２　３１ＳＷＡ６１０　００６８　

Turn Signal and Hazard Warning Indicators

The left or right turn signal indicator blinks when you signal a lane change or turn. If an indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page the bulb as soon as possible, since other drivers cannot see that you are signaling.

). Replace

293

When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.

Instrument Panel Indicators

High Beam Indicator

Low Fuel Indicator

This indicator comes on with the high beam headlights. For more information, see page

75

This indicator also comes on with reduced brightness when the daytime running lights (DRL) are on (see page

75

).

Daytime Running Lights Indicator

If this indicator comes on when you turn the ignition switch to the ON (II) position and release the parking brake, it means there is a problem with the DRL. There may also be a problem with the high beam headlights. Have your vehicle checked by your dealer.

This indicator comes on as a reminder that you must refuel soon.

When the indicator comes on, there is about 2.3 US gal (8.6 ) of fuel remaining in the tank before the reading reaches E. There is a small reserve of fuel remaining in the tank when the reading does reach E.

Door and Tailgate Open Monitor

The appropriate indicator comes on in this display if the tailgate or any door is not closed tightly.

63

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４２：３９　３１ＳＷＡ６１０　００６９　

Tire Pressure Monitoring System (TPMS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the TPMS. With this indicator on, the low tire pressure indicator will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked.

Lights On Indicator

or

This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the position. If you turn the

ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the light switch, this indicator will stay on. A reminder chime will also sound when you open the driver’s door.

Instrument Panel Indicators

Low Tire Pressure Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.

If this happens, pull to the side of the road when it is safe, check which tire has lost the pressure, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service (see page information, see page

). For more 258

312

332

64

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４２：４９　３１ＳＷＡ６１０　００７０　

Maintenance Minder Indicator

This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. It reminds you that it is time to take your vehicle in for scheduled maintenance. The maintenance main items and sub items will be displayed in the information display. See page 273
maintenance minder.

for more information on the

This indicator goes off when your dealer resets it after completing the required maintenance service.

Instrument Panel Indicators

Washer Level Indicator

Security System Indicator

SECURITY SYSTEM INDICATOR

WASHER LEVEL INDICATOR

Canadianmodelsonly This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator (see page

286

).

Ifequipped This indicator comes on when the security system is set. See page for more information on the 220
security system.

65

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４２：５４　３１ＳＷＡ６１０　００７１　

Gauges

INFORMATION DISPLAY

OUTSIDE TEMPERATURE INDICATOR

CURRENT FUEL MILEAGE

SPEEDOMETER

TACHOMETER

ODOMETER/AVERAGE FUEL MILEAGE/ CHECK FUEL CAP MESSAGE

U.S. model is shown.

FUEL GAUGE

TEMPERATURE GAUGE

SELECT/RESET KNOB

TRIP METER

66

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４３：０２　３１ＳＷＡ６１０　００７２　

The information display consists of three segments. The upper segment displays current fuel mileage, the second segment displays the odometer, average fuel mileage, range (estimated distance), engine oil life, and the lower segment displays the trip meter, and maintenance item code(s).

To switch the display, press and release the select/reset knob repeatedly. When you turn the ignition switch to the ON (II) position the last selection is displayed.

Gauges

Trip Meter This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it.

There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the select/reset knob repeatedly.

Each trip meter works independently, so you can keep track of two different distances.

When you turn the ignition switch to the ON (II) position, the last selection is displayed.

To reset a trip meter, display it, and then press and hold the select/reset knob until the number resets to ‘‘0.0’’.

67

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４３：１０　３１ＳＷＡ６１０　００７３　

Range (Estimated Distance) This display shows the estimated distance you can travel on the fuel remaining in the tank.

This distance is estimated from the fuel economy you have achieved over the last few miles (kilometers), so it will vary with changes in speed, traffic condition, etc.

Average Fuel Mileage When either of the trip meters (trip A or B) is displayed, your vehicle’s average fuel mileage since you last reset that trip meter can be shown on the information display (mpg on U.S. models and l/100 km on Canadian models). This number is updated once per 10 seconds. To see the average fuel mileage, press and release the select/reset knob repeatedly.

When you reset a trip meter, the average fuel mileage for that trip meter also resets.

Gauges

Current Fuel Mileage

Current Fuel Mileage

U.S. model is shown

This display shows the current, or instant fuel mileage you are getting.

It shows the number of mpg (U.S.) or l/100 km (Canada).

68

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４３：２０　３１ＳＷＡ６１０　００７４　

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the reading should be in the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the reading may reach near the red mark. If it reaches the red (Hot) mark, pull safely to the side of the road. See page instructions and precautions on checking the engine’s cooling system.

322

for

Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount.

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

Gauges

Outside Temperature Indicator

OUTSIDE TEMPERATURE INDICATOR

Ifequipped This indicator displays the outside temperature in Fahrenheit (U.S. models) or Centigrade (Canadian models).

CONTINUED

69

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４３：２７　３１ＳＷＡ６１０　００７５　

Gauges

The temperature sensor is in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your speed is under 19 mph (30 km/h).

The sensor delays the display update until it reaches the correct outside temperature. This may take several minutes.

If the outside temperature is incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.

5°F in U.S. models (

±

NOTE: The temperature must be stabilized before doing this procedure.

70

To adjust the outside temperature display, press and hold the select/ reset knob for 10 seconds. The display changes as shown above. Select the outside temperature indicator by turning the select/reset knob. The display begins to blink. Push the same knob to enter this setting, then turn it to adjust the temperature. The following sequence will appear for each: 0, 1, 2, 5, 3, 4, 5, 1, 0 (U.S.) 2, 1, 0 (Canada). or 0, 1, 2, 3, − − −

− − − − −

4, 3,

3, 2,

When it reaches the desired value, push the select/reset knob to enter the setting. You should see the new outside temperature displayed.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４３：３２　３１ＳＷＡ６１０　００７６　

Check Fuel Cap Message If your fuel fill cap is loose or missing, a ‘‘CHECK FUEL CAP’’ message appears on the information display after you start the engine. For more information, see page

228

Maintenance Minder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.

273

for

Gauges

71

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４３：４０　３１ＳＷＡ６１０　００７７　

Controls Near the Steering Wheel

HEADLIGHTS/TURN SIGNALS (P.74)

INSTRUMENT PANEL BRIGHTNESS

(P.76)

WINDSHIELD WIPERS/ WASHERS (P.73)

PASSENGER AIRBAG OFF INDICATOR (P.32)

HAZARD WARNING BUTTON (P.76)

SHIFT LEVER (P.247)

REAR WINDOW DEFOGGER BUTTON (P.77) HEATED MIRROR BUTTON (P.112)

＊

VEHICLE STABILITY ASSIST (VSA) SYSTEM ON/OFF SWITCH (P.257)

MIRROR CONTROL

(P.112)

REMOTE AUDIO CONTROLS ＊ (P.216)

STEERING WHEEL ADJUSTMENTS (P.78)

HORN ＊

CRUISE CONTROL BUTTON (P.222)

ACCESSORY POWER SOCKET (P.120)

VOICE CONTROLS

＊

PARKING BRAKE PEDAL (P.78)

To use the horn, press the center pad of the steering wheel. If equipped. Refer to the navigation system manual.

1 : 2 : 3 :

＊ ＊ ＊ 72

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４３：５０　３１ＳＷＡ６１０　００７８　

Windshield Wiper

ADJUSTMENT RING

1. 2. 3. 4. 5. 6.

MIST OFF INT LO Low speed HI High speed Windshield washers

Intermittent

− − −

Windshield Wipers and Washers

Push the right lever up or down to select a position.

MIST The wipers run at high speed until you release the lever.

−

OFF

−

The wipers are not activated.

−

Windshield Washers Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.

−

The wipers operate every

INT few seconds. At low speed and high speed, the wipers run continuously.

OnallmodelsexceptLX The length of the wiper interval is varied automatically according to the vehicle’s speed. Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( position), the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20km/h).

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

73

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４４：００　３１ＳＷＡ６１０　００７９　

Windshield Wipers and Washers, Turn Signal and Headlights

Rear Window Wiper and Washer

4.

Rotate the switch counterclockwise also to spray the window washer and turn the wiper on.

Turn Signal and Headlights

When you shift the transmission to the reverse position with the front windshield wiper activated, the rear wiper operates automatically even if the rear wiper switch is off.

The rear window washer uses the same fluid reservoir as the wind- shield washer.

1. 2. 3. 4. 5. 6.

Turn Signal OFF Parking and interior lights Headlights on High Beams Flash high beams

1.

2.

3.

OFF When you turn the wiper switch to the ‘‘OFF’’ position, the wiper will return to its parked position. Rotate the switch clockwise to turn the rear window wiper ON. The wiper operates every 7
seconds after completing two sweeps. Hold past ON to activate the rear window wiper a few times and to spray the rear window washer.

74

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４４：０８　３１ＳＷＡ６１０　００８０　

−

Turn Signal Push down on the lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever, and hold it. The lever will return to center when you release it or complete a turn.

−

Turning the switch to

’’ position turns on the

Headlights the ‘‘ parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate light.

When the light switch is in either of these positions, the lights on indicator comes on as a reminder.

This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.

−

Push the lever

High Beams forward and the high beam indicator will come on (see page back to return to low beams.

). Pull it

63

Turning the switch to the ‘‘ ’’ position turns on the headlights. If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.

To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.

Turn Signals and Headlights

position, the high beam

Daytime Running Lights With the headlight switch in the off or headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake. The headlights revert to normal operation when you turn them on with the switch.

75

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４４：１６　３１ＳＷＡ６１０　００８１　

Instrument Panel Brightness, Hazard Warning Button

Instrument Panel Brightness

INSTRUMENT PANEL BRIGHTNESS CONTROL KNOB

You can change the instrument panel brightness only when the light switch is on. Turn the knob on the lower part of the instrument panel to adjust the brightness. You will hear a beep when maximum or minimum brightness is reached.

76

To reduce glare at night, the instrument panel illumination dims when you turn the light switch to

or

. Turning the select/

reset knob fully to the right until you hear a beep will cancel the reduced brightness.

Hazard Warning Button

HAZARD WARNING BUTTON

Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４４：２３　３１ＳＷＡ６１０　００８２　

Rear Window Defogger

Onvehicleswithautomaticair conditioningsystem The defogger will shut itself off within about 10 to 30 minutes according to the outside temperature.

Make sure the rear window is clear and you have good visibility before starting to drive.

The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side.

Ifequipped Pushing this button also turns the mirror heaters on or off. For more information, see page

112

Manual A/C type is shown.

The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. It also shuts off when you turn off the ignition switch. You have to turn the defogger on again when you restart the vehicle.

77

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４４：３１　３１ＳＷＡ６１０　００８３　

Parking Brake, Steering Wheel Adjustment

Parking Brake

Driving the vehicle with the parking brake applied can damage the rear brakes and axles. A beeper will sound if the vehicle is driven with the parking brake on.

PARKING BRAKE PEDAL

To apply the parking brake, push the pedal down with your foot. To release it, push on the pedal again. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page

60

).

78

Steering Wheel Adjustment Make any steering wheel adjustment before you start driving.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

1.

Push the lever under the steering column all the way down.

2.

Move the steering wheel up or down, and in or out, so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４４：４０　３１ＳＷＡ６１０　００８４　

Steering Wheel Adjustment, Keys and Locks

Keys and Locks

KEY NUMBER TAG

MASTER KEY WITH REMOTE TRANSMITTER

VALET KEY (Gray)

LEVER

3.

Push the lever up to lock the steering wheel in position.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.

The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the glove box locked when you leave your vehicle and the valet key at a parking facility.

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.

These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.

Protect the keys from direct sunlight, high temperature, and high humidity.

Do not drop the keys or set heavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

The valet key does not contain a battery. Do not try to take it apart.

79

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４４：４８　３１ＳＷＡ６１０　００８５　

Immobilizer System

The Immobilizer System protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.

When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.

The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.

80

If the system repeatedly does not recognize the coding of your key, contact your dealer.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable.

If you have lost your key and cannot start your engine, contact your dealer.

Always take the ignition key with you whenever you leave the vehicle alone.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４４：５６　３１ＳＷＡ６１０　００８６　

Ignition Switch

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

You will hear a reminder beeper if you leave the key in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

−

You can

ACCESSORY (I) operate the audio system and the accessory power sockets in this position.

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly.

−

This is the normal key

ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.

−

Use this position

START (III) only to start the engine. The switch returns to the ON (II) position when you let go of the key.

The shift lever must be in Park before you can remove the key from the ignition switch.

81

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４５：０４　３１ＳＷＡ６１０　００８７　

Door Locks

Power Door Locks

Unlock

Lock

Lock

MASTER DOOR LOCK SWITCH

Unlock

RED INDICATOR

To lock all doors and the tailgate, push the top of the master door lock switch on either front door, pull the lock tab rearward on the driver’s door, or use the key on the outside lock on the driver’s door.

The lock tab on any passenger’s door locks and unlocks that door.

When the door is unlocked, you can see the red indicator on the lock tab above the inner door handle.

Pushing the bottom of the either master door lock switch will unlock all doors and the tailgate. Pushing forward the lock tab on the driver’s doors unlocks only that door.

82

All doors and the tailgate can be locked from the outside by using the key in the driver’s door lock. To unlock only the driver’s door, insert the key, turn the key, and release it. The remaining doors and the tailgate unlock when you turn the key a second time within a few seconds.

To lock any passenger’s door when getting out of the vehicle, pull the lock tab rearward and close the door. To lock the driver’s door, remove the key from the ignition switch, pull the lock tab rearward or push the top of the master switch, then close the door.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４５：１２　３１ＳＷＡ６１０　００８８　

Door Locks

LockoutPrevention With any door and the tailgate open and the key in the ignition, locking with master door lock switches is disabled. The lock tab on the driver’s door is not disabled if the driver’s door is closed. Pulling the driver’s lock tab rearward will lock all doors and the tailgate. If you try to lock an open driver’s door by pulling the lock tab rearward, the lock tab on the driver’s door pops out and unlocks the driver’s door.

Auto Door Locking/Unlocking Your vehicle has customizable settings for the doors and tailgate to automatically lock and unlock. There are default settings for each of these features. You can turn off or change the settings for these features as described on the following pages.

When you customize the setting, make sure your vehicle is parked safely, the engine is off, and apply the parking brake. Make all settings before you start driving.

Auto Door Locking The auto door locking feature has three possible settings:

The auto door locking is deactivated all the time.

The doors and the tailgate lock whenever you move the shift lever out of the Park (P) position.

The doors and the tailgate lock when the vehicle speed reaches 9 mph (15 km/h). This is the factory setting.

83

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４５：２１　３１ＳＷＡ６１０　００８９　

Door Locks

ToturnofftheAutoDoorLock modes:

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and open the driver’s door.

84

3.

Push and hold the front of the master door lock switch on the driver’s door until you hear a click (after about 5 seconds).

ToprogramtheParkLockmode: Locksalldoorsandtailgatewhenthe shiftleverismovedoutofthePark(P) position.

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４５：３１　３１ＳＷＡ６１０　００９０　

ToprogramtheDriveLockmode: Locksalldoorsandtailgatewhenthe vehicle’sspeedreachesabout9mph (15km/h).

3.

Push and hold the front of the master door lock switch on the driver’s door. You will hear a click. Keep holding the switch until you hear another click (after about 5
seconds).

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

Door Locks

3.

4.

Push and hold the brake pedal, and move the shift lever out of the Park (P) position.

Push and hold the front of the master door lock switch on the driver’s door. You will hear a click. Keep holding the switch until you hear another click (after about 5
seconds).

5.

Release the switch and, within 5
seconds, turn the ignition switch to the ACCESSORY (I) position. Move the shift lever to the Park (P) position.

1.

Make sure the shift lever is in the Park (P) position.

6.

Turn the ignition switch to the LOCK (0) position.

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

85

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４５：４２　３１ＳＷＡ６１０　００９１　

Door Locks

Auto Door Unlocking The auto door unlocking feature has five possible settings:

ToturnofftheAutoDoorUnlock modes:

The auto door unlocking is deactivated all the time.

The driver’s door unlocks when you move the shift lever to the Park (P) position. This is the default setting.

All doors and tailgate unlock when you move the shift lever to the Park (P) position.

The driver’s door unlocks whenever you turn the ignition switch to the ACCESSORY (I) position.

All doors and tailgate unlock whenever you turn the ignition switch to the ACCESSORY (I) position.

86

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and open the driver’s door.

3.

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click, and after about 5 seconds, you will hear another click.

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４５：５３　３１ＳＷＡ６１０　００９２　

ToprogramtheParkUnlockmode: Unlocksthedriver’sdoororalldoors andtailgatewhentheshiftleveris movedtoPark(P)position.

3.

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold down the switch:

Until you hear another click (after about 5 seconds) to activate driver’sdoorunlock feature,

Or, until you hear two more clicks (after about 10 seconds) to activate alldoorsandtailgate unlockfeature

4.

Release the switch, and within 5
seconds, turn the ignition switch to the LOCK (0) position.

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

Door Locks

ToprogramtheIgnitionSwitch Unlockmode: Unlocksthedriver’sdoororalldoors andtailgatewhentheignitionswitchis movedoutoftheON(II)position.

1.

Make sure the shift lever is in the Park (P) position.

2.

Turn the ignition switch to the ON (II) position, and make sure to close the driver’s door.

CONTINUED

87

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４６：０１　３１ＳＷＡ６１０　００９３　

Door Locks

3.

4.

Push and hold the brake pedal, then move the shift lever out of the Park (P) position.

Push and hold the rear of the master door lock switch on the driver’s door. You will hear a click. Continue to hold down the switch:

5.

Release the switch and, within 5
seconds, turn the ignition switch to the ACCESSORY (I) position. Move the shift lever to the Park (P) position.

6.

Turn the ignition switch to the LOCK (0) position.

Until you hear another click (after about 5 seconds) to activate driver’sdoorunlock feature,

Or, until you hear two more clicks (after about 10 seconds) to activate alldoorsandtailgate unlockfeature

88

Childproof Door Locks

LEVER

Unlock

Lock

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position (lever is down), the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, push the lock tab forward and use the outside door handle.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４６：０９　３１ＳＷＡ６１０　００９４　

Remote Transmitter

LOCK BUTTON

LED

UNLOCK BUTTON

PANIC BUTTON

−

LOCK Press this button once to lock all doors and the tailgate. Some exterior lights will flash once. When you push LOCK twice within 5
seconds, you will hear a beep to verify that the doors and the tailgate are locked and the security system (if equipped) has set. You cannot lock the doors and the tailgate if any door or the tailgate is not fully closed or the key is in the ignition switch.

−

Press this button once

UNLOCK to unlock the driver’s door. Push it twice to unlock the remaining doors and the tailgate. Some exterior lights will flash twice each time you press the button.

The ceiling light and the spot light (if equipped) comes on when you press the UNLOCK button if the lights are in the door activated position. If you do not open any door or the tailgate within 30 seconds, the light fades out. If you relock the doors and the tailgate with the remote transmitter before 30 seconds have elapsed, the light(s) will go off immediately.

If you do not open any door or the tailgate within 30 seconds, they will automatically relock, and the security system (if equipped) will reset.

−

Press this button for

PANIC about 2 seconds to attract attention: the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position.

CONTINUED

89

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４６：１７　３１ＳＷＡ６１０　００９５　

Remote Transmitter

RemoteTransmitterCare

Avoid dropping or throwing the transmitter.

Protect the transmitter from extreme temperature.

Do not immerse the transmitter in any liquid.

If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.

Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors and the tailgate, replace the battery as soon as possible. Battery type: CR1616

SCREW

To replace the battery:

1.

Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.

90

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４６：２５　３１ＳＷＡ６１０　００９６　

4.

Remove the old battery, and insert a new battery into the back of the cover with the

side facing down.

＋

BATTERY

An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.

TAB

5.

Install the parts in reverse order.

2.

3.

Separate the transmitter by prying its middle seam with your fingernail.

Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.

Remote Transmitter

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

91

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４６：３１　３１ＳＷＡ６１０　００９７　

Tailgate

The tailgate will lock when you lock the driver’s door with the key, the remote transmitter, the master door lock switch, or the lock tab on the driver’s door.

To unlock the tailgate, turn the key clockwise twice, push the rear of the master door lock switch, or push the UNLOCK twice on the remote transmitter.

92

RELEASE

HANDLE

To open the tailgate, push the release, and lift up. To close the tailgate, use the tailgate handle to lower it, then press down on the back edge.

Keep the tailgate closed at all times while driving to avoid damaging the tailgate and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard 54

on page

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１４：４６：３８　３１ＳＷＡ６１０　００９８　

Unlocking the Tailgate

RELEASE LEVER

If the power door lock system cannot unlock the tailgate, unlock it manually.

Place a cloth on the top side of the