2008 Honda CR V Owners Manual

performed, and make sure to reset the display as described as follows.

276

Maintenance Main Items and Sub Items

SUB ITEM (S)

MAIN ITEM

All maintenance items displayed on the information display are in code. For an explanation of these maintenance codes, see page

279

Resetting the Engine Oil Life Display Your dealer will reset the display after completing the required maintenance service. You will see ‘‘OIL LIFE 100%’’ on the information display the next time you turn the ignition switch to the ON (II) position.

If maintenance service is done by someone other than your dealer, reset the maintenance minder as follows:

1.

Turn the ignition switch to the ON (II) position.

2.

Press the select/reset knob repeatedly until the engine oil life is displayed.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１１：４７　３１ＳＷＡ６１０　０２８２　

Maintenance Minder

Important Maintenance Precautions If you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the proper maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed.

Your authorized Honda dealer knows your vehicle best and can provide competent, efficient service.

CONTINUED

277

EX and EX-L model

3.

Press the select/reset knob for about 10 seconds. The information display shows the reset mode initial display as shown.

4.

5.

Select the ‘‘OIL LIFE’’ indicator by turning the select/reset knob. The display begins to blink. Push the same knob to enter this setting.

The engine oil life and the maintenance item code(s) will begin to blink. Push the select/ reset knob to reset.

6.

The maintenance item code(s) will disappear, and the engine oil life will reset to ‘‘100.’’

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１１：５７　３１ＳＷＡ６１０　０２８３　

Maintenance Minder

However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Make sure to have the service facility or person reset the display as previously described. Keep all receipts as proof of completion, and have the person who does the work fill out your Honda Service History or Canadian Maintenance Log. Check your warranty booklet for more information.

We recommend using Honda parts and fluids whenever you have maintenance done. These are manufactured to the same high quality standards as the original components, so you can be confident of their performance and durability.

278

Maintenance,

U.S. Vehicles: replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.

＃

According to state and federal regulations, failure to perform maintenance on the items marked with will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the information display.

Owner’s Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed.

Engine oil level time you fill the fuel tank. See page

Check every

230

−

Engine coolant level radiator reserve tank every time you fill the fuel tank. See page

Check the

230

−

Automatic transmission Check the fluid level monthly. See page 287

−

Brakes monthly. See page

−

Check the fluid level

289

−

Tires Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 302

−

Check the operation of

Lights the headlights, parking lights, taillights, high-mount brake light, and license plate light monthly. See page

291

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１２：０５　３１ＳＷＡ６１０　０２８４　

Maintenance Minder

Symbol

Maintenance Main Items

Replace engine oil ＊ Replace engine oil and oil filter ＊ Inspect front and rear brakes Check parking brake adjustment Inspect these items:

Tie rod ends, steering gear box, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system ＃ Fuel lines and connections ＃

＊

1 :

If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every year.

＃

: See information on maintenance and emissions warranty on page

278

Symbol

Maintenance Sub Items

Rotate tires Replace air cleaner element

If you drive in dusty conditions, replace every 15,000 miles (24,000 km).

Replace dust and pollen filter

If you drive primarily in urban areas that have high concentrations of soot in the air from industry and from diesel-powered vehicles, replace every 15,000
miles (24,000 km).

Inspect drive belt Replace transmission fluid

If you tow a CR-V behind a motorhome, the transmission fluid must be changed every 2 years or 30,000 miles (48,000 km), whichever comes first.

Replace spark plugs Inspect valve clearance Replace engine coolant Replace rear differential fluid ＊

NOTE:

Independent of the maintenance items in the information display, replace the brake fluid every 3 years. Inspect idle speed every 160,000 miles (256,000 km). Adjust the valves during services A, B, 1, 2, or 3 only if they are noisy.

＊

2 :

4WD

279

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１２：０８　３１ＳＷＡ６１０　０２８５　

Fluid Locations

ENGINE OIL FILL CAP

ENGINE OIL DIPSTICK (Orange handle)

WASHER FLUID (Blue cap)

POWER STEERING FLUID (Red cap)

AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop)

280

BRAKE FLUID (Black cap)

ENGINE COOLANT RESERVOIR

RADIATOR CAP

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１２：１６　３１ＳＷＡ６１０　０２８６　

Adding Engine Oil

ENGINE OIL FILL CAP

Unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil slowly and carefully so you do not spill any. Clean up any spills immediately. Spilled oil could damage components in the engine compartment.

Reinstall the engine oil fill cap, and tighten it securely. Wait a few minutes, and recheck the oil level on the engine oil dipstick. Do not fill

Adding Engine Oil

above the upper mark; you could damage the engine.

Recommended Engine Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade 5W-20
detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements.

API CERTIFICATION SEAL

Honda Motor Oil is the preferred 5W-20 lubricant for your vehicle. It is highly recommended that you use Honda Motor Oil in your vehicle for optimum engine protection. Make sure the API Certification Seal says ‘‘For Gasoline Engines.’’

The oil viscosity or weight is provided on the container’s label. 5W-20 oil is formulated for year- round protection of your vehicle to improve cold weather starting and fuel economy.

Ambient Temperature

281

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１２：２５　３１ＳＷＡ６１０　０２８７　

Adding Engine Oil, Changing the Engine Oil and Filter

Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil: it displays the API certification seal, and it is the proper weight. You must follow the oil and filter change intervals shown on the information display.

Engine Oil Additives Your vehicle does not require any oil additives. Additives may adversely affect the engine or transmission performance and durability.

Changing the Engine Oil and Filter Always change the oil and filter according to the maintenance messages shown on the information display. The oil and filter collect contaminants that can damage your engine if they are not removed regularly.

Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service station- type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled mechanic.

WASHER

OIL DRAIN BOLT

1.

2.

Run the engine until it reaches normal operating temperature, then shut it off.

Open the hood, and remove the engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.

282

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１２：３４　３１ＳＷＡ６１０　０２８８　

Changing the Engine Oil and Filter

OIL FILTER

3.

4.

Remove the oil filter, and let the remaining oil drain. A special wrench (available from your dealer) is required.

Make sure the oil filter gasket is not stuck to the engine block. If it is, remove it before installing a new oil filter.

5.

Install a new oil filter according to the instructions that come with it.

6.

Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten the drain bolt to: 29 lbf·ft (39 N·m , 4.0 kgf·m)

7.

Refill the engine with the recom- mended oil.

Engine oil change capacity (including filter): 4.4 US qt (4.2 )

8.

Replace the engine oil fill cap. Start the engine. The oil pressure indicator should go out within 5
seconds. If it does not, turn off the engine, and check your work.

9.

Let the engine run for several minutes, then check the drain bolt and oil filter for leaks.

10.

Turn off the engine and let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil.

Improper disposal of engine oil can be harmf ul to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground.

283

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１２：４１　３１ＳＷＡ６１０　０２８９　

Engine Coolant

Adding Engine Coolant

RESERVE TANK

If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks.

284

If the reserve tank is completely empty, you should also check the coolant level in the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

Always use Honda Long-life Anti- freeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent water. Never add straight antifreeze or plain water.

If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１２：４９　３１ＳＷＡ６１０　０２９０　

RADIATOR CAP

1.

Make sure the engine and radiator are cool.

2.

Relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down.

3.

Remove the radiator cap by pushing it down and turning it counterclockwise.

Engine Coolant

6.

Pour coolant into the reserve tank. Fill it halfway between the MAX and MIN marks. Put the cap back on the reserve tank.

Do not add any rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or engine components.

4.

The coolant level should be up to the base of the filler neck. Add coolant if it is low.

Pour the coolant slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment.

5.

Put the radiator cap back on, and tighten it fully.

285

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１２：５５　３１ＳＷＡ６１０　０２９１　

Windshield Washers

Check the fluid level in the windshield washer reservoir at least monthly during normal use.

LEVEL GAUGE

Check the fluid level by removing the cap and looking at the level gauge.

Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather.

When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition the blade edges.

Do not use engine antif reeze or a vinegar/water solution in the windshield washer reservoir. Antif reeze can damage your vehicle’s paint, while a vinegar/water solution can damage the windshield washer pump. Use only commercially-available windshield washer f luid.

OnCanadianmodels: level indicator comes on when the level is low (see page

The low washer

65

).

286

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１３：０５　３１ＳＷＡ６１０　０２９２　

DIPSTICK

UPPER MARK LOWER MARK

Check the fluid level with the engine at normal operating temperature.

1.

Park the vehicle on level ground. Start the engine, let it run until the radiator fan comes on, then shut off the engine. For accurate results, wait about 60 seconds (but no longer than 90 seconds) before doing step 2.

2.

3.

Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth.

Insert the dipstick all the way into the transmission securely as shown in the illustration.

Automatic Transmission Fluid

4.

5.

Remove the dipstick and check the fluid level. It should be between the upper and lower marks.

If the level is below the lower mark, add fluid into the dipstick hole to bring it to the level between the upper and lower marks.

Pour the fluid slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment.

Always use Honda ATF-Z1
(automatic transmission fluid).

CONTINUED

287

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１３：１１　３１ＳＷＡ６１０　０２９３　

Automatic Transmission Fluid

Use only Honda Genuine ATF-Z1
(Automatic Transmission Fluid). Do not mix with other transmission f luids. Using transmission f luid other than Honda Genuine ATF-Z1 may cause deterioration in transmission operation and durability, and could result in damage to the transmission. Damage resulting f rom the use of transmission f luid other than Honda Genuine ATF-Z1 is not covered by the Honda new vehicle warranty.

6.

Insert the dipstick all the way back into the transmission securely as shown in the illustration.

Make sure the rubber cap on the dipstick fits in the dipstick guide and that you push the dipstick in all the way.

If you are not sure how to add fluid, contact your dealer.

288

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１３：２０　３１ＳＷＡ６１０　０２９４　

Rear Differential Fluid 4WDmodelonly The rear differential should be drained and refilled with new fluid according to the maintenance messages shown on the information display. Have your dealer replace the rear differential fluid.

Use Honda Dual Pump Fluid II only. Do not use automatic transmission fluid (ATF).

Rear Differential Fluid, Brake Fluid

Brake Fluid Check the fluid level in the brake fluid reservoir monthly.

Replace the brake fluid according to the maintenance messages shown on the information display.

Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3
or DOT 4 fluid, from a sealed container, as a temporary replacement.

Using any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible.

Brake fluid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.

MAX

MIN

The fluid level should be between the MIN and MAX marks on the side of the reservoir. If the level is at or below the MIN mark, your brake system needs attention. Have the brake system inspected for leaks or worn brake pads.

289

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１３：２６　３１ＳＷＡ６１０　０２９５　

Always use Honda Power Steering Fluid. You may use another power steering fluid as an emergency replacement, but have the power steering system flushed and refilled with Honda PSF as soon as possible.

A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently, and have the system inspected as soon as possible.

Turning the steering wheel to f ull lef t or right lock and holding it there can damage the power steering pump.

Power Steering Fluid

UPPER LEVEL

LOWER LEVEL

Check the level on the side of the reservoir when the engine is cold. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If not, add power steering fluid to the UPPER LEVEL.

Pour the fluid slowly and carefully so you do not spill any. Clean up any spills immediately; it could damage components in the engine compartment.

290

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１３：３４　３１ＳＷＡ６１０　０２９６　

Lights

Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the cargo area or pull a trailer, readjustment may be required. Adjustments should be done by your dealer or other qualified technician.

Replacing a Headlight Bulb Your vehicle has halogen headlight bulbs. When replacing a bulb, handle it by its base, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.

Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.

1.

Open the hood.

To change the headlight bulb on the driver’s side, remove the under-hood fuse box from its stay by pulling it out.

CONTINUED

291

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１３：４２　３１ＳＷＡ６１０　０２９７　

Lights

5.

6.

Install the new bulb into the hole, making sure the tabs are in their slots. Pivot the hold-down wire back in place, and clip the end into the slot.

Install the rubber seal over the back of the headlight assembly. Make sure one of the three arrows on the rubber seal is facing up; it is marked ‘‘

.’’

→

2.

Remove the electrical connector from the bulb by pulling the connector straight back.

7.

Push the electrical connector onto the new bulb. Make sure it is connected securely. Turn on the headlights to test the new bulb.

3.

Remove the rubber weather seal by pulling on the tab.

8.

(Driver’s side) Reinstall the under-hood fuse box.

4.

Unclip the end of the hold-down wire from its slot. Pivot it out of the way, and remove the bulb.

292

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１３：５１　３１ＳＷＡ６１０　０２９８　

Replacing a Front Turn Signal Light Bulb

1.

Open the hood.

To change the turn signal bulb on the driver’s side, remove the engine coolant reserve tank by pulling it out of its holder.

2.

3.

Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

Lights

4.

Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.

5.

Turn on the lights to make sure the new bulb is working.

6.

(Driver’s side) Reinstall the coolant reserve tank.

293

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１４：００　３１ＳＷＡ６１０　０２９９　

Lights

Replacing a Parking Light/Front Side Marker Light Bulb

FUSE BOX

4.

Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.

5.

Turn on the lights to make sure the new bulb is working.

6.

(Driver’s side) Reinstall the fuse box in place securely.

1.

Open the hood.

To change the parking light/front side marker on the driver’s side, remove the fuse box from its stay by pulling out.

On the passenger’s side

2.

3.

Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

294

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１４：０９　３１ＳＷＡ６１０　０３００　

Replacing Rear Bulbs

COVER

SCREWS

Lights

BULBS

1.

Open the tailgate. Place a cloth on the edge of the cover. Remove the covers by carefully prying on the edge with a small flat-tip screwdriver.

2.

Use a Phillips-head screwdriver to remove the taillight assembly mounting screw under each cover.

3.

Pull the taillight assembly out of the rear pillar.

BULBS

4.

Determine which of the four bulbs is burned out: stop/taillight, back- up light, turn signal, or side marker.

5.

Remove the socket by turning it one-quarter turn counterclockwise.

CONTINUED

295

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１４：１８　３１ＳＷＡ６１０　０３０１　

Lights

6.

7.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

Reinstall the socket into the light assembly by turning it clockwise until it locks.

8.

Turn on the lights to make sure the new bulb is working.

9.

Align the clips on the taillight assembly with the holes in the body, then push the taillight assembly into place. Tighten the two mounting screws securely and reinstall the covers.

296

Replacing a High-mount Brake Light Bulb

1.

Open the tailgate. Unlatch the top of the cover by pulling back on it with your hands.

2.

Place a cloth on the side edge of the cover. Remove the cover by carefully prying on the edge with a small flat-tip screwdriver and pulling the cover off.

3.

Remove the socket from the light assembly by turning it one-quarter turn counterclockwise.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１４：２８　３１ＳＷＡ６１０　０３０２　

Lights, Cleaning the Seat Belts, Floor Mats

Cleaning the Seat Belts

Floor Mats

LOOP

4.

5.

6.

7.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. Press the brake pedal to make sure the new bulb is working. Put the socket back into the light assembly, and turn it clockwise to lock it in place. Put the cover back on the light assembly. Push it in until it locks in place.

If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air-dry before you use the vehicle. Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.

The driver’s floor mat that came with your vehicle hooks over the floor mat anchors. This keeps the floor mat from sliding forward and possibly interfering with the pedals.

CONTINUED

297

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１４：３４　３１ＳＷＡ６１０　０３０３　

Floor Mats, Audio Antenna, Dust and Pollen Filter

If you remove a floor mat, make sure to re-anchor it when you put it back in your vehicle.

If you use a non-Honda floor mat, make sure it fits properly and that it can be used with the floor mat anchors. Do not put additional floor mats on top of the anchored mats.

Audio Antenna

Your vehicle is equipped with an antenna at the rear of the roof . Bef ore using a ‘‘drive-through’’ car wash, remove the antenna by unscrewing it by hand. This prevents the antenna f rom being damaged by the car wash brushes.

Dust and Pollen Filter This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system.

Have your dealer replace the filter when this service is indicated by a maintenance message on the information display. It should be replaced every 15,000 miles (24,000
km) if you drive primarily in urban areas that have high concentrations of soot in the air, or if the flow from the heating and cooling system becomes less than usual.

298

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１４：４５　３１ＳＷＡ６１０　０３０４　

Check the condition of the wiper blades at least every six months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used.

FRONT

WIPER ARMS

Do not open the hood when the wiper arms are raised, or you will damage the hood and the wiper arms.

To replace a front wiper blade:

1.

Raise each wiper arm off the windshield, lifting the driver’s side first, then the passenger’s side.

LOCK TAB

2.

Disconnect the blade assembly from the wiper arm:

Press and hold the lock tab.

Slide the blade assembly toward the lock tab until it releases from the wiper arm.

Wiper Blades

When replacing a wiper blade, make sure not to drop the wiper blade or wiper arm down on the windshield.

BLADE

3.

Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder.

CONTINUED

299

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１４：５２　３１ＳＷＡ６１０　０３０５　

Wiper Blades

4.

Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade.

REINFORCEMENT

BLADE

TOP

Make sure the three rubber tabs inside the blade fit to each notch of the reinforcement, as shown.

300

6.

7.

Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place.

Lower the wiper arm down against the windshield, the passenger’s side first, then the driver’s side.

5.

Place the top of the wiper blade on the end of the blade assembly, and slide the blade onto the assembly in the direction pointed to by the arrow. Make sure the blade is completely installed.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１５：０２　３１ＳＷＡ６１０　０３０６　

REAR

To replace a rear wiper blade:

1.

Raise the wiper arm off the rear window.

2.

Disconnect the blade assembly from the wiper arm by pivoting the blade assembly upward.

3.

4.

Pull one end of the blade out from the holder. Slide the blade out of the holder.

Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade.

Wiper Blades

5.

Slide the new blade into the holder. Make sure it is engaged in the slot along its full length. Insert both ends of the blade into the holder. Make sure they are secure.

6.

Install the wiper blade assembly onto the wiper arm. Make sure it locks in place.

7.

Lower the wiper arm against the windshield.

301

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１５：１０　３１ＳＷＡ６１０　０３０７　

Inflation Guidelines Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort.

Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.

Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly.

Tires

To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.

The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced.

Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding tire inflation and maintenance.

302

The tire pressure monitoring system (TPMS) warns you when a tire pressure is low. See page more information.

258

for

Even though your vehicle is equipped with TPMS, we recommend that you visually check your tires every day. If you think a tire might be low, check it immediately with a tire gauge.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１５：１９　３１ＳＷＡ６１０　０３０８　

Use a gauge to measure the air pressure in each tire at least once a month. Even tires that are in good condition may lose 1 to 2 psi (10 to 20 kPa, 0.1 to 0.2 kgf/cm ) per month. Remember to check the spare tire at the same time.

Check the air pressures when the tires are cold. This means the vehicle has been parked for at least 3
hours, or driven less than 1 mile (1.6
km). Add or release air, if needed, to match the recommended cold tire pressures on this page.

If you check air pressures when the tires are hot [driven for several miles (kilometers)], you will see readings 4
to 6 psi (30 to 40 kPa, 0.3 to 0.4
kgf/cm ) higher than the cold readings. This is normal. Do not let air out to match the recommended cold air pressure. The tire will be underinflated.

You should get your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges.

While tubeless tires have some ability to self-seal if they are punctured, you should look closely for punctures if a tire starts losing pressure.

Tires

Recommended Tire Pressures The following chart shows the recommended cold tire pressures for most normal and high-speed driving conditions.

Tire Size

225/65R17 102T

Cold Tire Pressure for Normal Driving

Front/Rear: 30 psi (210 kPa , 2.1 kgf/cm )

The compact spare tire pressure is: 60 psi (420 kPa , 4.2 kgf/cm )

For convenience, the recommended tire sizes and cold tire pressures are on a label on the driver’s doorjamb.

For additional information about your tires, see page

338

303

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１５：２７　３１ＳＷＡ６１０　０３０９　

Tires

Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear.

You should look for:

Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions.

Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord.

Excessive tread wear.

304

INDICATOR LOCATION MARKS

A tire this worn gives very little traction on wet roads. You should replace the tire if you can see three or more tread wear indicators.

TREAD WEAR INDICATORS Your tires have wear indicators molded into the tread. When the tread wears down, you will see a 1/2
inch (12.7 mm) wide band across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１５：３４　３１ＳＷＡ６１０　０３１０　

Tire Service Life The service life of your tires is dependent on many factors, including, but not limited to, driving habits, road conditions, vehicle loading, inflation pressure, maintenance history, speed, and environmental conditions (even when the tires are not in use).

In addition to your regular inspections and inflation pressure maintenance, it is recommended that you have annual inspections performed once the tires reach five years old. It is also recommended that all tires, including the spare, be removed from service after 10 years from the date of manufacture, regardless of their condition or state of wear.

The last four digits of the TIN (tire identification number) are found on the sidewall of the tire and indicate Tire the date of manufacture (See Labeling

on page

340

).

Tires

Tire Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment.

Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel. When you have new tires installed, make sure they are balanced. This increases riding comfort and tire life. For best results, have the installer perform a dynamic balance.

On vehicles with aluminum wheels, improper wheel weights can damage your vehicle’s aluminum wheels. Use only Honda wheel weights f or balancing.

305

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１５：４３　３１ＳＷＡ６１０　０３１１　

Tires

Tire Rotation

Front

Front

(For Non-directional Tires and Wheels)

(For Directional Tires and Wheels)

To help increase tire life and distribute wear more evenly, rotate the tires according to the maintenance messages displayed on the information display. Move the tires to the positions shown in the diagram each time they are rotated. If you purchase directional tires, rotate only front-to-back. When the tires are rotated, make sure the air pressures are checked.

306

Replacing Tires and Wheels Replace your tires with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall).

It is best to replace all four tires at the same time. If that is not possible or necessary, replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.

Mixing radial and bias-ply tires on your vehicle can reduce braking ability, traction, and steering accuracy. Using tires of a different size or construction can cause the ABS and vehicle stability assist system (VSA) to work inconsistently.

The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the vehicle. Tire size and construction can affect wheel speed and may cause the system to activate.

If you ever replace a wheel, make sure that the wheel’s specifications match those of the original wheels.

Also be sure you use only TPMS specific wheels. If you do not, the tire pressure monitoring system will not work on that tire.

Replacement wheels are available at your dealer.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１５：５４　３１ＳＷＡ６１０　０３１２　

Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.

Always use the size and type of tires recommended in this owner’s manual.

Wheel and Tire Specifications

Wheels:

17 x 6 1/2J

Tires:

225/65R17 102T

338

for DOT tire quality

See page grading information, and page for tire size and labeling 340
information.

Winter Driving Tires marked ‘‘M S’’ or ‘‘All Season’’ on the sidewall have an all- weather tread design suitable for most winter driving conditions.

＋

For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.

SnowTires If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as original tires. Mount snow tires on all four wheels. The traction provided by snow tires on dry roads may be lower than your original tires. Check with the tire dealer for maximum speed recommendations.

Tires

TireChains Because your vehicle has limited tire clearance, mount only SAE Class ‘‘S’’ cable-type traction devices, with rubber chain tensioners, on the front tires. Use traction devices only when required by driving conditions or local laws. Make sure they are the correct size for your tires. Metal link- type ‘‘chains’’ should not be used.

CONTINUED

307

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１６：０１　３１ＳＷＡ６１０　０３１３　

Tires, Wheels, Checking the Battery

When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension. Drive slowly with them installed. If you hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads.

Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.

Wheels Clean the wheels as you would the rest of the exterior. Wash them with the same solution, and rinse them thoroughly.

Ifequipped Aluminum alloy wheels have a protective clear-coat that keeps the aluminum from corroding and tarnishing. Cleaning the wheels with harsh chemicals (including some commercial wheel cleaners) or a stiff brush can damage the clear-coat. To clean the wheels, use a mild detergent and a soft brush or sponge.

Checking the Battery

TEST INDICATOR WINDOW

Check the condition of the battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors.

308

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１６：０７　３１ＳＷＡ６１０　０３１４　

TEST INDICATOR WINDOW

Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent future corrosion.

If additional battery maintenance is needed, see your dealer or a qualified technician.

Battery posts,

WARNING: terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.

If you need to connect the battery to a charger, disconnect both cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative ( − reconnect it last.

) cable first, and

Checking the Battery

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled technician do the battery maintenance.

If your vehicle’s battery is disconnected, or goes dead, the audio system will disable itself. The next time you turn on the radio, you may see ‘‘CODE’’ in the frequency display. Use the preset buttons to enter the code (see page

218

).

309

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１６：１７　３１ＳＷＡ６１０　０３１５　

Vehicle Storage

If you need to park your vehicle for an extended period (more than 1
month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors.

Fill the fuel tank.

Wash and dry the exterior completely.

Clean the interior. Make sure the carpeting, floor mats, etc., are completely dry.

Leave the parking brake off. Put the transmission in Park.

310

Block the rear wheels.

If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.

Leave one window open slightly (if the vehicle is being stored indoors).

Disconnect the battery.

Support the front and rear wiper blade arms with a folded towel or rag so they do not touch the windshield.

To minimize sticking, apply a silicone spray lubricant to all door and tailgate seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and tailgate seals.

Cover the vehicle with a ‘‘breathable’’ cover, one made from a porous material such as cotton. Non-porous materials, such as plastic sheeting, trap moisture, which can damage the paint.

If possible, periodically run the engine until it reaches full operating temperature (the cooling fans cycle on and off twice). Preferably, do this once a month.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１６：２１　３１ＳＷＡ６１０　０３１６　

Taking Care of the Unexpected

This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed.

Compact Spare Tire Changing a Flat Tire If the Engine Won’t Start Jump Starting If the Engine Overheats Low Oil Pressure Indicator Charging System Indicator Malfunction Indicator Lamp Brake System Indicator Fuses Fuse Locations Emergency Towing

...................... .................... ............. ................................ .............. ......... .......... ....... ............... .............................................. .............................. ......................

. 312
. 313
. 318
. 320
. 322
. 324
. 324
. 325
. 326
. 327
. 330
. 332

311

2008 CR- V Main Menu０７／０７／２５　１５：１６：２９　３１ＳＷＡ６１０　０３１７　

Compact Spare Tire

Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can.

Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm )

Follow these precautions:

Never exceed 50 mph (80 km/h).

This tire gives a harsher ride and less traction on some road surfaces. Use greater caution while driving.

312

Do not mount snow chains on the compact spare tire.

Do not use your compact spare tire on another vehicle unless it is the same make and model.

The low tire pressure indicator comes on and stays on after you replace the flat tire with the compact spare tire. After several miles (kilometers) driving with the compact spare tire, the TPMS indicator comes on and the low tire pressure indicator goes off.

INDICATOR LOCATION MARK

TREAD WEAR INDICATOR BAR

Replace the tire when you can see the tread wear indicator bars. The replacement should be the same size and design tire, mounted on the same wheel. The spare tire is not designed to be mounted on a regular wheel, and the spare wheel is not designed for mounting a regular tire.

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１６：３９　３１ＳＷＡ６１０　０３１８　

Changing a Flat Tire

If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes.

SPARE TIRE

The vehicle can easily roll off the jack, seriously injuring anyone underneath.

Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.

1.

Park the vehicle on firm, level, and non-slippery ground. Put the transmission in Park. Apply the parking brake. If you are towing a trailer, unhitch the trailer.

TOOLS

JACK

2.

Turn on the hazard warning lights, and turn the ignition switch to the LOCK (0) position. Have all passengers get out of the vehicle while you change the tire.

3.

Open the tailgate. Raise the cargo area floor lid by lifting up with the strap, and remove it from cargo area by disengaging the tabs.

When you store the flat tire in the spare tire well, do not reinstall the cargo area floor lid forcibly. This will damage the tabs on the lid.

4.

Take the tool kit out of the spare tire.

CONTINUED

313

2008 CR- V Table Of ContentsMain Menu０７／０７／２５　１５：１６：４７　３１ＳＷＡ６１０　０３１９　

Changing a Flat Tire

WHEEL NUT WRENCH

JACK

5.

Take the jack out of the spare tire area.

7.

Loosen each wheel nut 1/2 turn with the wheel nut wrench.

Turn the jack’s end bracket counterclockwise to loosen it, then remove the jack by lifting it straight up.

6.

Unscrew the wing bolt and take the spare tire out of its well.

314

JACKING POINT

8.

Place the jack under the jacking point nearest the tire you need to