2003 Honda CR V Owners Manual

verify that it is secure enough to stay upright during normal driving maneuvers. If the child seat is not secure, unlatch the belt, allow it to retract fully, then repeat these steps.

Driver and Passenger Safety

41

０２／０７／２４　１４：３２：０４　３１Ｓ９Ａ６１０　００４７　

Protecting Children

Protecting Larger Children When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in the back seat on a booster and wear a lap/shoulder belt.

We recommend that the child use a booster seat until the child is tall enough to use the seat belt without a booster.

The following pages give instructions on how to check proper seat belt fit, what kind of booster seat to use if one is needed, and important precautions for a child who must sit in the front seat.

42

Driver and Passenger Safety

CheckingSeatBeltFit

Allowing a larger child to sit improperly in the front seat can result in injury or death if the passenger’s front airbag inflates.

If a larger child must sit in front, make sure the child moves the seat as far back as possible, uses a booster seat if needed, and wears the seat belt properly.

To determine if a lap/shoulder belt properly fits a child, have the child sit in the rear seat, all the way back against the seat and have them put on the seat belt. Follow the instructions on page how the belt fits.

. Then check

17

０２／０７／２４　１４：３２：１５　３１Ｓ９Ａ６１０　００４８　

If the shoulder part of the belt rests over the child’s collarbone and against the center of the chest, and if the lap belt rests over the child’s hipbones and touches the tops of their thighs as shown, the child is probably big enough to wear the seat belt.

However, if the shoulder belt touches or crosses the child’s neck, or if the lap belt crosses the child’s stomach, the child needs to use a booster seat.

Donotletachildwearaseatbelt acrosstheneckoroverthestomach. This could result in serious neck and internal injuries during a crash.

Donotletachildputtheshoulder partofaseatbeltbehindthebackor underthearm. very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.

This could cause

Donotputanyaccessoriesonaseat Devices intended to improve belt. occupant comfort or reposition the shoulder part of a seat belt, severely compromise the protective capability of the seat belt and increase the chance of serious injury in a crash.

Twochildrenshouldneverusethe If they do, they could sameseatbelt. be very seriously injured in a crash.

Protecting Children

UsingaBoosterSeat

If a child needs a booster seat, we recommend choosing a high or low- back style that allows the child to be directly secured with the lap/ shoulder belt.

Whichever style you select, follow the booster seat maker’s instructions.

CONTINUED

Driver and Passenger Safety

43

Of course, children vary widely. And while age may be one indicator of when a child can safely ride in the front, there are other important factors you should consider.

０２／０７／２４　１４：３２：２３　３１Ｓ９Ａ６１０　００４９　

Protecting Children

A child should continue using a booster seat until they exceed the booster seat manufacturer’s requirements.

Even then, they may still need to use a booster seat. Note that some states now require children to use boosters until they reach a certain age and/or weight. Be sure to check current laws in the state or states where you intend to drive.

44

Driver and Passenger Safety

WhenCanaLargerChildSitinFront The National Highway Traffic Safety Administration and Transport Canada recommend that all children ages 12 and under be properly restrained in the back seat.

The back seat is the safest place for a child of any age or size.

In addition, the passenger’s front airbag poses serious risks to children. If the seat is too far forward, or the child’s head is thrown forward during a collision, or the child is unrestrained or out of position, an inflating front airbag can kill or seriously injure the child.

The side airbag also poses risks. If any part of a larger child’s body is in the path of a deploying airbag, the child could receive possibly serious injuries.

０２／０７／２４　１４：３２：３３　３１Ｓ９Ａ６１０　００５０　

Protecting Children

PhysicalSize Physically, a child must be large enough for the lap/shoulder belt to properly fit over the hips, chest, and shoulder (see pages ). If the seat belt does not fit properly, the child should not sit in the front.

and

17

42

Maturity To safely ride in front, a child must be able to follow the rules, including sitting properly and wearing the seat belt properly throughout a ride.

If you decide that a child can safely ride up front, be sure to:

Carefully read the owner’s manual and make sure you understand all seat belt instructions and all safety information.

Move the vehicle seat to the rear- most position.

Have the child sit up straight, back against the seat, and feet on or near the floor.

Check that the child’s seat belt is properly positioned and secured.

Supervise the child. Even mature children sometimes need to be reminded to fasten the seat belts or sit properly.

Driver and Passenger Safety

45

０２／０７／２４　１４：３２：４２　３１Ｓ９Ａ６１０　００５１　

Protecting Children

Using Child Seats with Tethers

COVER

TETHER ANCHORAGE POINT

Your vehicle has three tether anchorage points on the ceiling near the tailgate opening for securing a tether-style child seat to the vehicle.

Since a tether can provide additional security, we recommend using a tether whenever one is required or available.

The tether anchorage points are located under plastic covers. Select the anchorage point you want to use, and remove the cover with a small flat-tipped screwdriver or fingernail file.

46

Driver and Passenger Safety

Remove the head restraint where you want to place the child seat.

You can remove the head restraint in each outside position by pressing the release button. The head restraint in the center position can be removed by pulling it up (see page

99

).

０２／０８／２２　２０：０９：０１　３１Ｓ９Ａ６１０　００５２　

Make sure the removed head restraints are secured in the cargo area. Reinstall the head restraints when the child seat is removed.

TETHER ANCHORAGE POINT

MARKS

Using LATCH

Protecting Children

TETHER STRAP HOOK Attach the tether strap hook to the tether anchorage point as shown in the illustration, then tighten the strap according to the child seat maker’s instructions. Make sure the strap is not twisted.

LOWER ANCHORS

Your vehicle is equipped with LATCH (Lower Anchors and Tethers for Children) at the outer rear seats. The lower anchors are located between the seat-back and seat bottom and are to be used only with a child seat designed for use with LATCH. The exact location of each lower anchor is marked with a small circle above the lower anchor point.

CONTINUED

Driver and Passenger Safety

47

０２／０８／２２　２０：０９：１０　３１Ｓ９Ａ６１０　００５３　

Protecting Children

To install a LATCH-compatible child seat:

1.

2.

Store the seat belt buckle in the pocket in the seat cushion and move the center seat belt away from the lower anchors.

Make sure there are no foreign objects around the anchors. Foreign objects could get in the way of a secure connection between the child seat and the anchors.

48

Driver and Passenger Safety

Rigid type

Flexible type

3.

Put the child seat in the rear left or right vehicle seat and attach the child seat to the lower anchors according to the child seat maker’s instructions.

4.

Follow the child seat maker’s instructions for any additional advice on adjusting or tightening the fit.

０２／０８／２２　２０：０９：２２　３１Ｓ９Ａ６１０　００５４　

Protecting Children

TETHER ANCHORAGE POINT

Lower Universal Anchorage System Symbol

6.

7.

TETHER STRAP HOOK Attach the tether strap hook to the tether anchorage point, and tighten the strap according to the child seat maker’s instructions. Make sure the strap is not twisted.

Push and pull the child seat forward and from side to side to verify that it is secure enough to stay upright during normal driving maneuvers.

This symbol on rear or forward facing child seats or booster cushions indicates the presence of LATCH compatible hardware.

Driver and Passenger Safety

49

5.

Remove the head restraint (see page

99

).

Make sure the removed head restraints are secured in the cargo area. Reinstall the head restraints when the child seat is removed.

０２／０７／２４　１４：３３：１５　３１Ｓ９Ａ６１０　００５５　

Additional Information About Your Seat Belts

Lap/Shoulder Belt

The lap/shoulder belt goes over your shoulder, across your chest, and across your hips.

To fasten the belt, insert the latch plate into the buckle, then tug on the belt to make sure the buckle is latched.

To unlock the belt, push the red PRESS button on the buckle. Guide the belt across your body to the door pillar. After exiting the vehicle, be sure the belt is out of the way and will not get closed in the door.

All seat belts have an emergency locking retractor. In normal driving, the retractor lets you move freely in your seat while it keeps some tension on the belt. During a collision or sudden stop, the retractor automatically locks the belt to help restrain your body.

Seat Belt System Components Your seat belt system includes lap/ shoulder belts in all five seating positions. The front seat belts are also equipped with automatic seat belt tensioners.

The seat belt system also includes a light on the

instrument panel to remind you and your passengers to fasten your belts. If the driver’s seat belt is not fastened before the ignition is turned ON (II), the light will come on and a beeper will also sound. The beeper will stop after a few seconds, but the light will stay on until the driver’s seat belt is fastened.

50

Driver and Passenger Safety

０２／０７／２４　１４：３３：２４　３１Ｓ９Ａ６１０　００５６　

The seat belts in all seating positions except the driver’s have an additional locking mechanism that must be activated to secure a child seat. (See pages for instructions on how to secure child seats with this type of seat belt.)

and

35

39

If the shoulder part of the belt is pulled all the way out, the locking mechanism will activate. The belt will retract, but it will not allow the passenger to move freely.

To deactivate the locking mechanism, unlatch the buckle and let the seat belt fully retract. To refasten the belt, pull it out only as far as needed.

17

for instructions on how

See page to wear the lap/shoulder belt properly.

Additional Information About Your Seat Belts

DETACHABLE ANCHOR

The lap/shoulder belt in the center seating position on the rear seat is equipped with a detachable anchor that has two parts: a small latch plate and an anchor buckle.

The detachable anchor should normaly be latched whenever the seat-backs are in an upright position. For more information about the detachable anchor (see page 108

).

Driver and Passenger Safety

51

The SRS indicator light will come on if there is a

problem with your automatic seat belt tensioners (see page

57

).

０２／０７／２４　１４：３３：３２　３１Ｓ９Ａ６１０　００５７　

Additional Information About Your Seat Belts

The tensioners are designed to activate primarily in frontal collisions. The tensioners are independent of the airbag system, so they can be activated during a collision that might not cause the airbags to deploy. In this case, the airbags would not be needed but the additional seat belt tension can be helpful.

The tensioners will be activated in a collision severe enough to cause the front airbags to inflate.

When the tensioners are activated, the seat belts will remain tight until they are unbuckled in the normal way.

Automatic Seat Belt Tensioners

For added protection, the front seat belts are equipped with automatic seat belt tensioners. When activated, the tensioners immediately tighten the belts to help hold the driver and a front passenger in place.

52

Driver and Passenger Safety

０２／０７／２４　１４：３３：４１　３１Ｓ９Ａ６１０　００５８　

Additional Information About Your Seat Belts

Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly.

Pull each belt out fully and look for frays, cuts, burns, and wear. Check that the latches work smoothly and that the lap/shoulder belts retract easily. Any belt not in good condition or not working properly will not provide good protection and should be replaced as soon as possible.

Not checking or maintaining seat belts can result in serious injury or death if the seat belts do not work properly when needed.

Check your seat belts regularly and have any problem corrected as soon as possible.

If a seat belt is worn during a crash, it must be replaced by the dealer. A belt that has been worn during a crash may not provide the same level of protection in a subsequent crash. The dealer should also inspect the anchors for damage and replace them if needed.

Automatic seat belt tensioners that deployed during a crash must be replaced.

U.S.Models Honda provides a lifetime warranty on seat belts. Honda will repair or replace any seat belt component that fails to function properly during normal use. Please see your WarrantyInformation details.

booklet for

Honda

For information on how to clean your seat belts, see page

302

Driver and Passenger Safety

53

０２／０７／２４　１４：３３：５２　３１Ｓ９Ａ６１０　００５９　

Additional Information About Your Airbags

An indicator light on the instrument panel that alerts you to a possible problem with the system (see page

57

).

Emergency backup power in case your vehicle’s electrical system is disconnected in a crash.

How Your Front Airbags Work

If you ever have a moderate to severe frontal collision, the sensors will detect the vehicle’s rapid deceleration If the rate of deceleration is high enough, the control unit will instantly inflate the front airbags and activate the automatic seat belt tensioners.

SRS Components Your Supplemental Restraint System (SRS) includes:

Two front airbags. The driver’s airbag is stored in the center of the steering wheel; the front passenger’s airbag is stored in the dashboard. Both are marked ‘‘SRS AIRBAG.’’

Automatic seat belt tensioners (see page

52

).

Sensors that can detect a moderate to severe frontal collision.

A sophisticated electronic system that continually monitors and records information about the sensors, the control unit, the airbag activators, and driver and passenger seat belt use when the ignition is ON (II).

54

Driver and Passenger Safety

０２／０７／２４　１４：３４：０２　３１Ｓ９Ａ６１０　００６０　

Additional Information About Your Airbags

During a frontal crash, your seat belts help restrain your lower body and torso. Your airbag provides a cushion to help restrain and protect your head and chest.

Since both airbags use the same sensors, both airbags normally inflate at the same time. However, it is possible for only one airbag to inflate.

This can occur when the severity of a collision is at the margin, or threshold, that determines whether or not the airbags will deploy. In such cases, the seat belt will provide sufficient protection, and the supplemental protection offered by the airbag would be minimal.

After a crash, you may see what looks like smoke. This is actually powder from the airbag’s surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the vehicle as soon as it is safe to do so.

U.S.Owners For additional information on how your airbags work, see the booklet titled SRS:WhatYouNeedtoKnow that came with your AboutAirbags owner’s manual.

CanadianOwners For additional information on how your airbags work, ask your dealer for a copy of the booklet titled SRS: WhatYouNeedtoKnowAboutAirbags.

Driver and Passenger Safety

55

After inflating, the front airbags immediately deflate, so they won’t interfere with the driver’s visibility, or the ability to steer or operate other controls.

The total time for inflation and deflation is approximately one-tenth of a second, so fast that most occupants are not aware that the airbags deployed until they see them lying in their laps.

０２／０７／２４　１４：３４：０９　３１Ｓ９Ａ６１０　００６１　

Additional Information About Your Airbags

How Your Side Airbags Work

To get the best protection from the side airbags, front seat occupants should wear their seat belts and sit upright and well back in their seats.

If you ever have a moderate to severe side impact, the sensors will detect rapid deceleration and signal the control unit to instantly inflate either the driver’s or the passenger’s side airbag.

Only one airbag will deploy during a side impact. If the impact is on the passenger’s side, the passenger’s side airbag will deploy even if there is no passenger.

StandardonEXmodelintheU.S.,and EXandEX-LmodelsinCanada Your vehicle is equipped with side airbags for the driver and a front seat passenger. The airbags are stored in the outer edges of the front seat-backs, and both are marked ‘‘SIDE AIRBAG.’’

56

Driver and Passenger Safety

０２／０７／２４　１４：３４：１９　３１Ｓ９Ａ６１０　００６２　

Additional Information About Your Airbags

How the SRS Indicator Light Works

The SRS indicator light alerts you to a potential

problem with your front airbags and automatic seat belt tensioners.

On models with side airbags, this light will also alert you to a potential problem with your side airbags or passenger’s side airbag automatic cutoff system (see page

58

).

When you turn the ignition ON (II), this indicator will light briefly then go out. This tells you that the system is working properly.

Ignoring the SRS indicator light can result in serious injury or death if the airbags, cutoff system, or tensioners do not work properly.

Have your vehicle checked by a dealer as soon as possible if the SRS light alerts you to a potential problem.

If the light comes on at any other time, or does not come on at all, you should have the system checked by your dealer. For example:

If the SRS indicator light does not come on after you turn the ignition switch to ON (II).

If the light stays on after the engine starts.

If the light comes on or flashes on and off while you drive.

If you see any of these indications, your front or side airbags may not deploy, your passenger’s side airbag automatic cutoff system may not work properly, or your seat belt tensioners may not work when you need them. See your Honda dealer as soon as possible.

Driver and Passenger Safety

57

０２／０７／２４　１４：３４：２８　３１Ｓ９Ａ６１０　００６３　

Additional Information About Your Airbags

If a small-statured adult leans sideways, or larger adult slouches and leans sideways into the deployment path of the side airbag, the system may also shut off the side airbag.

If the side airbag cutoff indicator light comes on, you should have the passenger sit upright. Once the passenger is out of the deployment path of the side airbag, the system will turn the airbag back on and the light will go out.

How the Side Airbag Cutoff Indicator Light Works Onlyonmodelsequippedwithside airbags

This light alerts you that the passenger’s side airbag

has been automatically shut off.

It does not mean there is a problem with your side airbags. It means that the side airbag cutoff system has activated to prevent the side airbag from deploying.

To reduce the risk of injury from an inflating side airbag, your vehicle has an automatic cutoff system for the passenger’s side airbag.

Although Honda does not encourage children to ride in the front, this system is designed to shut off the side airbag if a child leans sideways and the child’s head is in the side airbag deployment path.

58

Driver and Passenger Safety

A front seat passenger should not use a cushion or other object as a backrest. It may prevent the cutoff system from working properly.

When you turn the ignition switch to ON (II), the indicator should light briefly and go out (see page doesn’t light, stays on, or comes on while driving without a passenger in the front seat, have the system checked.

). If it

67

０２／０７／２４　１４：３４：３８　３１Ｓ９Ａ６１０　００６４　

Additional Information About Your Airbags

Improperly

Donotcoverorreplacefrontseat- backcoverswithoutconsultinga Hondadealer. replacing or covering front seat- back covers can prevent your side airbags from inflating during a collision.

192

for further information

See page and precautions relating to your airbags.

Additional Safety Precautions

Donotattempttodeactivateyour airbags. seat belts provide the best protection.

Together, airbags and

Donottamperwithairbag componentsorwiringforany Tampering could cause reason. the airbags to deploy, possibly causing very serious injury.

If rain or spilled water

Donotexposethefrontseat-backs towater. soaks into a seat-back, it can prevent the side airbag system from working properly.

Airbag Service Your front and side airbag systems (if equipped) are virtually maintenance-free, and there are no parts you can safely service. However, you must have your vehicle serviced if:

Any

Yourairbagseverinflate. airbag that has deployed must be replaced along with the control unit, automatic seat belt tensioners, and other related parts. Do not try to remove or replace any airbag by yourself. This must be done by a Honda dealer or a knowledgeable body shop.

TheSRSindicatorlightalertsyou Take your vehicle to toaproblem. an authorized Honda dealer as soon as possible. If you ignore this indication, the airbags might not inflate when you need them.

Driver and Passenger Safety

59

０２／０７／２４　１４：３４：４７　３１Ｓ９Ａ６１０　００６５　

Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you.

Avoid any enclosed areas or activities that expose you to carbon monoxide.

High levels of carbon monoxide can collect rapidly in enclosed areas, such as a garage. Do not run the engine with the garage door closed. Even with the door open, run the engine only long enough to move the vehicle out of the garage.

With the tailgate/hatch glass open, air flow can pull exhaust gas into your vehicle’s interior and create a hazardous condition. If you must drive with the tailgate/hatch glass open, open all the windows and set the heating and cooling system as shown below.

If you must sit in your parked vehicle, even in an unconfined area, with the engine running, adjust the heating and cooling system as follows:

1. 2. 3. 4.

Select the Fresh Air mode. Select the Turn the fan on high speed. Set the temperature control to a comfortable setting.

mode.

Carbon Monoxide Hazard

Your vehicle’s exhaust contains carbon monoxide gas. You should have no problem with carbon monoxide entering the vehicle in normal driving if you maintain your vehicle properly.

Have the exhaust system inspected for leaks whenever:

The vehicle is raised for an oil change. You notice a change in the sound of the exhaust. The vehicle was in an accident that may have damaged the under- side.

60

Driver and Passenger Safety

０２／０７／２４　１４：３５：０６　３１Ｓ９Ａ６１０　００６６　

These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully.

If a label comes off or becomes hard to read, contact your Honda dealer for a replacement.

DASHBOARD U.S.modelsonly

Safety Labels

SUN VISOR U.S.models

Canadianmodels

SUN VISOR U.S.modelsonly

CONTINUED

Driver and Passenger Safety

61

０２／０７／２４　１４：３５：１６　３１Ｓ９Ａ６１０　００６７　

Safety Labels

HOOD Onmodelswithoutsideairbags

Onmodelswithsideairbags

62

Driver and Passenger Safety

RADIATOR CAP

０２／０７／２４　１４：３５：２２　３１Ｓ９Ａ６１０　００６８　

Instruments and Controls

This section gives information about the controls and displays that contribute to the daily operation of your Honda. All the essential controls are within easy reach.

Control Locations Indicator Lights Gauges

........................... ............................... ............................................. ............................... ................................. ..............

Speedometer Tachometer Odometer/Trip Meter Outside Temperature

. 64
. 65
. 72
. 72
. 72
. 73

Indicator Fuel Gauge Temperature Gauge

.................................. .................................. ...................

. 73
. 74
. 74

Controls Near the Steering

Wheel

Headlights

....................................... ...................................

. 75
. 76

Keys and Locks

Daytime Running Lights Instrument Panel Brightness Turn Signals Windshield Wipers Windshield Washers Rear Window Wiper and

............ .... ................................ ..................... ..................

Washer

Hazard Warning Rear Window Defogger Parking Brake Steering Wheel Adjustment

..................................... .......................... ............. ............................. ...... ............................... .............................................. .................... ............................ ...................... ................... .............. ........................................ .................................... ................................................. .............

Keys Immobilizer System Ignition Switch Power Door Locks Remote Transmitter Childproof Door Locks Tailgate Glove Box

Front Seat Adjustments Driver’s Seat Height

. 77
. 77
. 77
. 78
. 79

. 80
. 81
. 81
. 82
. 83
. 84
. 84
. 85
. 86
. 88
. 89
. 93
. 93
. 96
. 97
. 97

Adjustment

Front Seat Armrests Head Restraints

.............................. ................... ..........................

. 98
. 98
. 99

Seats

Seat Heaters Power Windows Moonroof Mirrors

Rear Seat Adjustments Rear Seat Armrest Reclining the Front Seats Folding the Rear Seats Detachable Anchor

. 100
............ . 101
.................... . 102
........ . 104
............. . 108
................... . 109
.................................. . 110
............................ . 113
....................................... ........................................... . 114
.. Adjusting the Power Mirrors . 114
.................................. . 115
. 116
......................... . 117
................................. . 119
............................... . 119
................................... ............................. . 120
. 120
....................................... . 121
........................ . 122
............ ........................ . 123
. 124
............................... . 124
.............................. . 124
................................... . 125
...................... ................ . 125

Center Table Beverage Holders Built-in Table Center Pocket Storage Box Driver’s Pocket Coin Tray Sunglasses Holder Accessory Power Sockets Dashboard Pocket Interior Lights Ceiling Light Spotlights Cargo Area Light Ignition Switch Light

Instruments and Controls

63

０２／０７／２４　１４：３５：２８　３１Ｓ９Ａ６１０　００６９　

Control Locations

POWER DOOR LOCK SWITCH (P.88)

MIRROR CONTROLS (P.114)

POWER WINDOW SWITCHES (P.110)

HOOD RELEASE HANDLE (P.186)

HATCH GLASS RELEASE BUTTON (P.94)

A/T model is shown.

64

Instruments and Controls

AUDIO SYSTEM (P.138, 154) DIGITAL CLOCK (P.144, 162)

PARKING BRAKE (P.82)

FUEL FILL DOOR RELEASE HANDLE (P.185)

HEATING/COOLING CONTROLS (P.128)

０２／０７／２４　１４：３５：３８　３１Ｓ９Ａ６１０　００７０　

ANTI-LOCK BRAKE SYSTEM INDICATOR ＊ (P.68)

LOW OIL PRESSURE INDICATOR (P.66, 325)

SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P.67)

TAILGATE AND HATCH GLASS OPEN INDICATOR (P.70)

Indicator Lights

IMMOBILIZER SYSTEM INDICATOR (P.68)

MALFUNCTION INDICATOR LAMP (P.327)

CHARGING SYSTEM INDICATOR (P.66, 326)

SIDE AIRBAG CUTOFF INDICATOR (P.67)

CRUISE CONTROL (P.69) INDICATOR

LOW FUEL INDICATOR (P.69)

MAINTENANCE REQUIRED INDICATOR (P.70)

SEAT BELT REMINDER LIGHT (P.67)

HIGH BEAM INDICATOR (P.69)

DOOR-OPEN INDICATOR (P.70)

PARKING BRAKE AND BRAKE SYSTEM INDICATOR ＊ (P.66)

＊

The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.

Instruments and Controls

65

０２／０７／２４　１４：３５：４９　３１Ｓ９Ａ６１０　００７１　

Indicator Lights

The instrument panel has many indicators to give you important information about your vehicle.

Malfunction Indicator Lamp 327

See page

Low Oil Pressure Indicator

The engine can be severely damaged if this light flashes or stays on when the engine is running. For complete information, see page

325

Charging System Indicator

If this light comes on when the engine is running, the battery is not being charged. For complete information, see page

326

66

Instruments and Controls

U.S.

Canada

Parking Brake and Brake System Indicator

This light has two functions:

1.

2.

This indicator comes on when you turn the ignition switch ON (II). It is a reminder to check the parking brake. Driving with the parking brake not fully released can damage the brakes and tires.

If the indicator remains lit after you have fully released the parking brake while the engine is running, or if it comes on while driving, it can indicate a problem in the brake system. For complete information, see page

329

０２／０７／２４　１４：３５：５８　３１Ｓ９Ａ６１０　００７２　

Indicator Lights

Seat Belt Reminder Light

This indicator lights when you turn the ignition switch ON (II). It is a reminder to you and your passengers to protect yourselves by fastening the seat belts. A beeper also sounds if you have not fastened your seat belt.

If you do not fasten your seat belt, the beeper will stop after a few seconds but the light stays on until you do. Both the light and the beeper stay off if you fasten your seat belt before turning on the ignition.

Supplemental Restraint System Indicator

This indicator lights when you turn the ignition switch ON (II). If it comes on at any other time, it indicates a potential problem with your front airbags or automatic seat belt tensioners. On models equipped with side airbags, this light will also alert you to a potential problem with your side airbags or passenger’s side airbag automatic cutoff system. For complete information, see page 57

Side Airbag Cutoff Indicator

Onlyonmodelsequippedwithside airbags This indicator lights when you turn the ignition switch ON (II). If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. For complete information, see page 58

Instruments and Controls

67

０２／０７／２４　１４：３６：０７　３１Ｓ９Ａ６１０　００７３　

Immobilizer System Indicator

This indicator comes on for a few seconds when you turn the ignition switch ON (II). It will then go off if you have inserted a properly-coded ignition key. If it is not a properly- coded key, the indicator will blink and the engine will not start (see page

85

).

This indicator also blinks several times when you turn the ignition switch from ON (II) to ACCESSORY (I) or LOCK (0).

Turn Signal and Hazard Warning Indicators The left or right turn signal light blinks when you signal a lane change or turn. If the light does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see page ). Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.

288

When you turn on the Hazard Warning switch, both turn signal lights blink. All turn signals on the outside of the vehicle should flash.

Indicator Lights

U.S.

Anti-lock Brake System (ABS) Indicator OnlyonmodelsequippedwithABS(see page )212
This light normally comes on for a few seconds when you turn the ignition switch ON (II), and when the ignition switch is turned to START (III). If this light comes on at any other time, there is a problem in the ABS. If this happens, take the vehicle to your dealer to have it checked. With the light on, your vehicle still has normal braking ability but no anti-lock. For complete information, see page

214

68

Instruments and Controls

０２／０７／２４　１４：３６：１９　３１Ｓ９Ａ６１０　００７４　

‘‘Daytime Running Lights’’ Indicator

Canadianmodelsonly This indicator lights when you turn the ignition switch to ON (II) with the headlight switch off and the parking brake set. It should go off if you turn on the headlights or release the parking brake. If it comes on at any other time, it means there is a problem with the DRL. There may also be a problem with the high beam headlights.

Cruise Control Indicator

This lights when you set the cruise control. See page on operating the cruise control.

for information

179

Indicator Lights

High Beam Indicator

Washer Level Indicator

This light comes on with the high beam headlights. See page for 76
information on the headlight controls.

On Canadian models, this indicator comes on with reduced brightness when the Daytime Running Lights (DRL) are on (see page

77

).

Canadianmodelsonly This light comes on when the washer fluid level is low. Add washer fluid when you see this light come on (see page

258

).

Low Fuel Indicator

This light comes on as a reminder that you must refuel soon.

Instruments and Controls

69

０２／０７／２４　１４：３６：２９　３１Ｓ９Ａ６１０　００７５　

Maintenance Required Indicator

This indicator reminds you that it is time to take your vehicle in for scheduled maintenance. Refer to the Maintenance Schedules for Normal and Severe Driving Conditions on pages 242

238

−

For the first 8,000 miles (12,800 km) after the Maintenance Required Indicator is reset, it will come on for two seconds when you turn the ignition switch to ON (II).

Between 8,000 miles (12,800 km) and 10,000 miles (16,000 km) this indicator will light for two seconds when you first turn the ignition switch to ON (II), and then flash for ten seconds.

If you exceed 10,000 miles (16,000
km) without having the scheduled maintenance performed, this indicator will remain on as a constant reminder.

Indicator Lights

Tailgate and Hatch Glass Open Indicator

This light comes on if the tailgate or the hatch glass is not closed tightly.

Door-open Indicator

This light comes on if any door is not closed tightly.

70

Instruments and Controls

０２／０７／２４　１４：３６：３７　３１Ｓ９Ａ６１０　００７６　

Indicator Lights

Your dealer will reset this indicator after completing the scheduled maintenance. If this maintenance is done by someone other than your Honda dealer, reset the indicator as follows.

1.

Turn off the engine.

2.

Press and hold the Select/Reset button on the instrument panel, then turn the ignition switch ON (II).

3.

Hold the button until the indicator resets (approximately ten seconds).

Instruments and Controls

71

０２／０７／２４　１４：３６：４５　３１Ｓ９Ａ６１０　００７７　

Gauges

TACHOMETER

SPEEDOMETER

FUEL GAUGE

TEMPERATURE GAUGE

SELECT/RESET BUTTON

ODOMETER/TRIP METER

72

Instruments and Controls

Speedometer U.S.models This shows your speed in miles per hour (mph). The smaller inner numbers are the speed in kilometers per hour (km/h).

Canadianmodels This shows your speed in kilometers per hour (km/h). The smaller inner numbers are the speed in miles per hour (mph).

Tachometer The tachometer shows the engine speed in revolutions per minute (rpm). To protect the engine from damage, never drive with the tachometer needle in the red zone.

０２／０７／２４　１４：３６：５４　３１Ｓ９Ａ６１０　００７８　

Odometer/Trip Meter The odometer shows the total dis- tance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

The trip meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Switch between these displays and the odometer by pressing the Select/Reset button repeatedly. Each trip meter works independently, so you can keep track of two different distances.

Gauges

To reset a trip meter, display it, and then press and hold the Select/Reset button until the number resets to ‘‘0.0’’.

OutsideTemperatureIndicator

OUTSIDE TEMPERATURE INDICATOR

Canadianmodelsonly This indicator displays the outside temperature in Centigrade.

CONTINUED

Instruments and Controls

73

０２／０７／２４　１４：３７：０３　３１Ｓ９Ａ６１０　００７９　

Gauges

The temperature sensor is located in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road sur- face, engine heat, and the exhaust from the surrounding traffic. This can cause the temperature reading not to be correct when your speed is under 19 mph (30 km/h).

When the outside temperature goes down below 37°F (3°C) the first time, the temperature reading blinks about ten times to show you the outside temperature is low. In certain weather conditions, temperature readings near freezing 32°F (0°C) could mean that ice is forming on the road surface.

Fuel Gauge This shows how much fuel you have. It is most accurate when the vehicle is on level ground. It may show slightly more or less than the actual amount when you are driving on curvy or hilly roads.

The needle returns to the bottom after you turn off the ignition. The gauge shows the fuel level reading immediately after you turn the ignition switch back ON (II).

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom white mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper white zone. If it reaches the red (Hot) mark, pull safely to the side of the road. Turn to page 323
instructions and precautions on checking the engine’s cooling system.

for

74

Instruments and Controls

０２／０７／２４　１４：３７：１３　３１Ｓ９Ａ６１０　００８０　

The two levers on the steering column contain controls for driving features you use most often. The left lever controls the turn signals, headlights, and high beams. The right lever controls the windshield washers and wipers.

The hazard warning lights switch is on the dashboard between the center air vents.

The controls under the left air vent are for the moonroof and the cruise control.

The tilt adjustment lever on the underside of the steering column allows you to tilt the steering wheel.

Controls Near the Steering Wheel

HEADLIGHTS/TURN SIGNALS (P.76, 77)

SHIFT LEVER (A/T) (P.204)

MOONROOF (P.113)

WINDSHIELD WIPERS/ WASHERS (P.78, 79)

HAZARD WARNING LIGHTS (P.81)

CRUISE CONTROL (P.179)

HORN ＊

TILT ADJUSTMENT (P.83)

PARKING BRAKE (P.82)

REAR WINDOW DEFOGGER (P.81)

A/T model is shown.

＊

To use the horn, press the center pad of the steering wheel.

Instruments and Controls

75

０２／０７／２４　１４：３７：２１　３１Ｓ９Ａ６１０　００８１　

Controls Near the Steering Wheel

Headlights

If you leave the lights on with the ignition switch in ACCESSORY (I) or LOCK (0), you will hear a reminder tone when you open the driver’s door.

’’ position turns

The rotating switch on the left lever controls the lights. Turning this switch to the ‘‘ on the parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate light. Turning the switch to the ‘‘ ’’ position turns on the headlights.

76

Instruments and Controls

To change from low beams to high beams, push the turn signal lever forward until you hear a click. The blue high beam indicator will light (see page ). To return to low beams, pull the turn signal lever back.

69

To flash the high beams, pull the turn signal lever back lightly, then release it. The high beams will come on and go off. The high beams will stay on for as long as you hold the lever back, no matter what position the headlight switch is in.

０２／０７／２４　１４：３７：３２　３１Ｓ９Ａ６１０　００８２　

Daytime Running Lights Canadianmodelsonly With the headlight switch off, the high beam headlights come on with reduced brightness when you turn the ignition switch to ON (II) and release the parking brake. They remain on until you turn the ignition off, even if you set the parking brake.

The headlights revert to normal operation when you turn them on with the switch.

Controls Near the Steering Wheel

Instrument Panel Brightness

Turn Signals

Turn the knob on the left side of the instrument panel to adjust the brightness of the instrument panel lights.

TURN SIGNAL LEVER

Signal a turn or lane change with this lever. Push down on the lever to signal a left turn, and up to signal a right turn. If you push it up or down all the way, the turn signal continues to blink even when you release the lever. It shuts off automatically as you complete the turn.

CONTINUED

Instruments and Controls

77

０２／０７／２４　１４：３７：３９　３１Ｓ９Ａ６１０　００８３　

Controls Near the Steering Wheel

To signal a lane change, push lightly on the turn signal lever in the proper direction and hold it. The lever will return to the center position as soon as you release it.

Windshield Wipers

In intermittent, the wipers operate every few seconds. In low speed and high speed, the wipers run continu- ously.

This lever controls the windshield wipers and washers. It has five positions:

MIST: mist OFF: off INT: intermittent LO: low speed HI: high speed

To select a position, push the lever up or down.

78

Instruments and Controls

０２／０７／２４　１４：３７：４５　３１Ｓ９Ａ６１０　００８４　

Controls Near the Steering Wheel

Windshield Washers

The wipers run at low speed while you’re pulling the lever, then complete one more sweep of the windshield after you release it.

To operate the wipers in mist mode, push the control lever up from the OFF position. The wipers run at high speed until you release the lever. This gives you a quick way to clear the windshield.

To clean the windshield, pull back on the wiper control lever. The washers spray until you release the lever.

Instruments and Controls

79

The rear window washer uses the same fluid reservoir as the wind- shield washer.

０２／０７／２４　１４：３７：５４　３１Ｓ９Ａ６１０　００８５　

Controls Near the Steering Wheel

To use the wiper and washer, rotate and hold the switch one position up from ‘‘ON’’. The wiper opreates while you are holding the switch, then completes two more sweeps after you release it. To use the washer only, rotate and hold the switch one position down from ‘‘OFF’’.

The rear wiper will not work if the hatch glass is not fully closed.

If you open the hatch glass while the rear wiper is operating, the wiper will stop immediately. To store it, rotate the wiper switch to the ‘‘OFF’’ position and close the hatch glass, then turn the wiper switch on and off again with the ignition switch on.

Rear Window Wiper and Washer

The rotating switch on the right lever controls the rear window wiper and washer.

To activate the rear windshield wiper, rotate the switch to ‘‘ON’’. The wiper operates every seven seconds after completing two sweeps. When you turn the wiper switch to the ‘‘OFF’’ position or turn off the ignition switch, the wiper will return to its parked position.

80

Instruments and Controls

０２／０７／２４　１４：３８：０３　３１Ｓ９Ａ６１０　００８６　

Hazard Warning

Rear Window Defogger

Controls Near the Steering Wheel

Make sure the rear window is clear and you have good visibility before starting to drive.

The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side.

Push the button between the center air vents to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The light in the button lights to show the defogger is on.

Instruments and Controls

81

０２／０７／２４　１４：３８：１１　３１Ｓ９Ａ６１０　００８７　

Controls Near the Steering Wheel

Parking Brake

RELEASE BUTTON

Driving the vehicle with the parking brake applied can damage the rear brakes and axles.

PARKING BRAKE LEVER

To apply the parking brake, firmly pull the parking brake lever toward you.

To release the parking brake, push and hold the release button on the side of the parking brake lever, pull the lever toward you slightly, then push the lever forward.

The parking brake light on the instrument panel should go out when the parking brake is fully released (see page

66

).

82

Instruments and Controls

０２／０７／２４　１４：３８：２２　３１Ｓ９Ａ６１０　００８８　

Steering Wheel Adjustment See page for important safety information about how to properly position the steering wheel.

20

Make any steering wheel adjustment before you start driving.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Controls Near the Steering Wheel

3.

Push the lever up to lock the steering wheel in that position.

4.

Make sure you have securely locked the steering wheel in place by trying to move it up and down.

To adjust the steering wheel upward or downward:

Adjust the steering wheel only when the vehicle is stopped.

1.

Push the lever under the steering column all the way down.

2.

Move the steering wheel to the desired position, making sure the wheel points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and the indicator lights.

Instruments and Controls

83

０２／０７／２４　１４：３８：３３　３１Ｓ９Ａ６１０　００８９　

The valet key works only in the ignition, the door locks and the tailgate. You can keep the glove box locked when you leave your vehicle and the valet key at a parking facility.

These keys contain electronic circuits that are activated by the Immobilizer System. They will not work to start the engine if the circuits are damaged.

You should have received a key number tag with your set of keys. You will need this key number if you ever have to get a lost key replaced. Keep the tag stored in a safe place. When replacing keys, use only Honda-approved key blanks.

Protect the keys from direct sunlight, high temperature, and high humidity.

Do not drop the keys or set heavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immedi- ately with a soft cloth.

The keys do not contain batteries. Do not try to take them apart.

Keys and Locks

Keys

KEY NUMBER TAG

MASTER KEYS (Black)

VALET KEY (Gray)

Your vehicle comes with two master keys and a valet key. The master key fits all the locks on your vehicle: (cid:127) Ignition (cid:127) Doors (cid:127) Glove Box (cid:127) Tailgate

84

Instruments and Controls

０２／０７／２４　１４：３８：４２　３１Ｓ９Ａ６１０　００９０　

RemoteTransmitter Some models also come with two remote transmitters; see page 89
an explanation of their operation.

for

Immobilizer System The Immobilizer System protects your vehicle from theft. A properly- coded master or valet key must be used in the ignition switch for the engine to start. If an improperly- coded key (or other device) is used, the engine’s fuel system is disabled.

When you turn the ignition switch to ON (II), the Immobilizer System indicator should come on for a few seconds, then go out. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to LOCK (0), remove the key, reinsert it, and turn the switch to ON (II) again.

Keys and Locks

The system may not recognize your key’s coding if another immobilizer key or other metal object is near the ignition switch when you insert the key. To make sure the system recognizes the key code:

Do not keep other immobilizer keys on the same key ring.

Use a plastic or leather key fob, not metal.

Keep other keys away from your vehicle’s key and the ignition switch while trying to start the engine.