Download PDF Manual


Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.


Always use the size and type of tires recommended in this owner’s manual.


Replacing Tires and Wheels Replace your tires with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall).


Mixing radial and bias-ply tires on your vehicle can reduce braking ability, traction, and steering accuracy. Using tires of a different size or construction can cause the ABS to work inconsistently.


It is best to replace all four tires at the same time. If that is not possible or necessary, replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.


The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the vehicle. Tire size and construction can affect wheel


Main MenuTable of Contentsst 05/09/09 18:24:52 31SNC600 0214 


Wheel and Tire Specifications Wheels:


15 x 6 J


Tires:


P195/65R15 89S


244


for DOT tire quality


See page grading information, and page for tire size information. 246


Winter Driving Tires marked ‘‘M S’’ or ‘‘All Season’’ on the sidewall have an all- weather tread design suitable for most winter driving conditions.



For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.


Tires


When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension. Drive slowly with them installed. If you hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads.


Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.


SnowTires If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as original tires. Mount snow tires on all four wheels. The traction provided by snow tires on dry roads maybelowerthanyouroriginaltires. Check with the tire dealer for maximum speed recommendations.


TireChains Because your vehicle has limited tire clearance, mount only SAE Class ‘‘S’’ cable-type traction devices, with rubber chain tensioners on the front tires. Use traction devices only when required by driving conditions or local laws. Make sure they are the correct size for your tires. Metal link- type ‘‘chains’’ should not be used.


211


Main MenuTable of Contentsst 05/09/09 18:24:59 31SNC600 0215 


Checking the 12 Volt Battery


Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent further corrosion.


If additional battery maintenance is needed, see your dealer or a qualified technician.


Battery posts,


WARNING: terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.


If you need to connect the battery to a charger, disconnect both cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative ( − reconnect it last.


) cable first, and


The battery gives off explosive hydrogen gas during normal operation.


A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.


Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.


If your vehicle’s 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading will not be correct the next time you turn the ignition switch to the ON (II) position. It will show less than the actual level temporarily. It will show the correct level after you drive for at least 30 minutes.


TEST INDICATOR WINDOW


Check the condition of the 12 volt battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors.


212


Main MenuTable of Contentsst 05/09/09 18:25:10 31SNC600 0216 


Vehicle Storage


If you need to park your vehicle for an extended period (more than 1
month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors.


Fill the fuel tank.


Block the rear wheels.


If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.


Leave one window open slightly (if the vehicle is being stored indoors).


Change the engine oil and filter.


Disconnect the 12 volt battery.


Cover the vehicle with a ‘‘breathable’’ cover, one made from a porous material such as cotton. Non-porous materials, such as plastic sheeting, trap moisture, which can damage the paint.


Reconnect the 12 volt battery and drive your vehicle every month for about 30 minutes. This will keep the IMA battery charged and in good condition.


Wash and dry the exterior completely.


Clean the interior. Make sure the carpeting, floor mats, etc., are completely dry.


Leave the parking brake off. Put the transmission in Park.


Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield.


To minimize sticking, apply a silicone spray lubricant to all door and trunk seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and trunk seals.


If possible, periodically run the engine until it reaches full operating temperature (the cooling fan cycles twice). Preferably, do this once a month.


213


Main MenuTable of Contentsst 05/09/09 18:25:16 31SNC600 0218 


Taking Care of the Unexpected


This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed.


Compact Spare Tire Changing a Flat Tire If the Engine Won’t Start Jump Starting If the Engine Overheats Low Oil Pressure Indicator Charging System Indicator Malfunction Indicator Lamp Brake System Indicator Fuses Fuse Locations Emergency Towing


...................... .................... ............. ................................ .............. ......... .......... ....... ............... .............................................. .............................. ......................


. 216
. 217
. 221
. 223
. 225
. 227
. 228
. 229
. 230
. 231
. 235
. 237


215


Main Menust 05/09/09 18:25:23 31SNC600 0219 


Compact Spare Tire


Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can.


Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm )


216


Follow these precautions:


INDICATOR LOCATION MARK


Never exceed 50 mph (80 km/h).


This tire gives a harsher ride and less traction on some road sur- faces. Use greater caution while driving.


Do not mount snow chains on the compact spare tire.


Do not use your compact spare tire on another vehicle unless it is the same make and model.


TREAD WEAR INDICATOR BAR


Replace the tire when you can see the tread wear indicator bars. The replacement should be the same size and design tire, mounted on the same wheel. The spare tire is not designed to be mounted on a regular wheel, and the spare wheel is not designed for mounting a regular tire.


Main MenuTable of Contentsst 05/09/12 13:50:42 31SNC600 0220 


If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes.


The vehicle can easily roll off the jack, seriously injuring anyone underneath.


Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.


1.


2.


Park the vehicle on firm, level, and non-slippery ground. Put the transmission in Park. Apply the parking brake.


Turn on the hazard warning lights, and turn the ignition switch to the LOCK (0) position. Have all passengers get out of the vehicle while you change the tire.


Changing a Flat Tire


JACK


TOOL CASE


TRUNK FLOOR SPARE TIRE Open the trunk. Raise the trunk 3. floor by lifting up on the back edge.


4.


Take the tool case out of the spare tire.


5.


Unscrew the wing bolt, and take the spare tire out of its well.


CONTINUED


217


Main MenuTable of Contentsst 05/09/10 14:32:13 31SNC600 0221 


Changing a Flat Tire


JACKING POINTS


6.


Remove the center cap from the wheel with the extension.


7.


Loosen each wheel nut 1/2 turn with the wheel nut wrench.


WHEEL NUT WRENCH


8.


Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting in the jack notch.


218


Main MenuTable of Contentsst 05/09/10 14:32:23 31SNC600 0222 


BRAKE HUB


11.


Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully; it may be hot from driving.


WHEEL NUT WRENCH 9.


EXTENSION Use the extension and the wheel nut wrench as shown to raise the vehicle until the flat tire is off the ground.


10.


Remove the wheel nuts, then remove the flat tire. Handle the wheel nuts carefully; they may be hot from driving. Place the flat tire on the ground with the outside surface facing up.


Changing a Flat Tire


12.


Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel nut wrench until the wheel is firmly against the hub. Do not try to tighten them fully.


13.


Lower the vehicle to the ground, and remove the jack.


CONTINUED


219


Main MenuTable of Contentsst 05/09/09 18:25:55 31SNC600 0223 


Changing a Flat Tire


WING BOLT


SPACER CONE


19.


Store the jack in the tool case.


Loose items can fly around the interior in a crash and could seriously injure the occupants.


Store the wheel, jack, and tools securely before driving.


20.


Store the center cap in the trunk. Make sure it does not get scratched or damaged.


21.


Lower the trunk floor, and close the trunk lid.


For normal tire


For spare tire


16.


Place the flat tire face down in the spare tire well.


17.


Remove the spacer cone from the wing bolt, turn it over, and put it back on the bolt.


18.


Secure the flat tire by screwing the wing bolt back into its hole.


14.


Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. Tighten the wheel nuts to: 80 lbf·ft (108 N·m , 11 kgf·m)


15.


Remove the center cap before storing the flat tire in the trunk well.


220


Main MenuTable of Contentsst 05/09/09 18:26:04 31SNC600 0224 


If the Engine Won’t Start


Diagnosing why the engine won’t start falls into two areas, depending on what you hear when you turn the ignition switch to the START (III) position:


You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly.


You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.


Nothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to the START (III) position, you do not hear the normal noise of the engine trying to start. You may hear a clicking sound or series of clicks, or nothing at all. Check these things:


Check the transmission interlock. The transmission must be in Park or neutral or the starter will not operate.


Turn the ignition switch to the ON (II) position. Turn on the headlights, and check their brightness. If the headlights are very dim or do not come on at all, the battery is discharged. See Jump Starting


on page


223


Turn the ignition switch to the START (III) position. If the headlights do not dim, check the condition of the fuses. If the fuses areOK,thereisprobably something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the problem (see Emergency Towing


on page


237


).


If the headlights dim noticeably or go out when you try to start the engine, either the battery is discharged or the connections are corroded. Check the condition of the 12 volt battery and terminal connections (see page 212
canthentryjumpstartingthe vehicle from a booster battery (see page


). You


223


).


221


Main MenuTable of Contentsst 05/09/09 18:26:10 31SNC600 0225 


If you find nothing wrong, you will need a qualified technician to find the problem. See Towing on page


Emergency 237


If the Engine Won’t Start


The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to the START (III) position, but the engine does not run.


Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the instrument panel to blink rapidly (see page ).


59


Are you using the proper starting Starting the procedure? Refer to Engine 165


on page


Do you have fuel? Check the fuel gauge; the low fuel indicator may not be working.


There may be an electrical problem, such as no power to the fuel pump. Check all the fuses (see page


231


).


222


Main MenuTable of Contentsst 05/09/09 18:26:19 31SNC600 0226 


Although this seems like a simple procedure, you should take several precautions.


To jump start your vehicle:


1.


Open the hood, and check the physical condition of the 12 volt battery.


A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.


Keep all sparks, open flames, and smoking materials away from the battery.


You cannot start your vehicle by pushing or pulling it.


If a battery sits in extreme cold, the electrolyte inside can f reeze. Attempting to jump start with a f rozen battery can cause it to rupture.


2.


Turn off all electrical accessories: heater, A/C, climate control, audio system, lights, etc. Put the transmission in Park, and set the parking brake.


Jump Starting


BOOSTER BATTERY


The numbers in the illustration show you the order to connect the jumper cables.


3.



) terminal on your


Connect one jumper cable to the positive ( battery. Connect the other end to the positive ( ) terminal on the + booster battery.


CONTINUED


223


Main MenuTable of Contentsst 05/09/09 18:26:26 31SNC600 0227 


Jump Starting


If your vehicle’s 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading will not be correct the next time you turn the ignition switch to the ON (II) position. It will show less than the actual level temporarily. It will show the correct level after you drive for at least 30 minutes.


6.


7.


Start the vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact.


Once your vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from your vehicle, then from the booster battery.


Keep the ends of the jumper cables away from each other and any metal on the vehicle until everything is disconnected. Otherwise, you may cause an electrical short.


4.



Connect the second jumper cable to the negative ( ) terminal on the booster battery. Connect the other end to the grounding strap as shown. Do not connect this jumper cable to any other part of the engine.


5.


If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle.


224


Main MenuTable of Contentsst 05/09/09 18:26:34 31SNC600 0228 


The reading on the vehicle’s temperature gauge should stay in the midrange. If it climbs to the red mark, you should determine the reason (hot day, driving up a steep hill, etc.).


If your vehicle overheats, you should take immediate action. The only indicationmaybethetemperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood.


Driving with the temperature gauge reading at the red mark can cause serious damage to the engine.


Steam and spray from an overheated engine can seriously scald you.


Do not open the hood if steam is coming out.


1.


2.


Safely pull to the side of the road. Put the transmission in Park, and set the parking brake. Turn off all accessories, and turn on the hazard warning indicators.


If you see steam and/or spray coming from under the hood, turn off the engine. Wait until you see no more signs of steam or spray, then open the hood.


If the Engine Overheats


3.


4.


5.


If you do not see steam or spray, leave the engine running, and watch the temperature gauge. If the high heat is due to overloading, the engine should start to cool down almost immediately. If it does, wait until the temperature gauge reading comes down to the midpoint, then continue driving.


If the temperature gauge reading stays at the red mark, turn off the engine.


Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you Emergency continue driving (see Towing ). 237


on page


CONTINUED


225


Main MenuTable of Contentsst 05/09/09 18:26:41 31SNC600 0229 


10.


11.


8.


9.


Using gloves or a large heavy cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. After the pressure releases, push down on the cap, and turn it until it comes off.


Start the engine, and set the temperature control dial to maximum. Add coolant to the radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can.


If the Engine Overheats


6.


7.


If you do not find an obvious leak, check the coolant level in the radiator reserve tank. Add coolant if the level is below the MIN mark.


If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the reading reaches the middle of the temperature gauge or lower before checking the radiator.


Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.


Always let the engine and radiator cool down before removing the radiator cap.


226


Put the radiator cap back on tightly. Run the engine, and watch the temperature gauge. If it goes back to the red mark, the engine needs repair (see Towing on page


Emergency 237


).


If the temperature stays normal, check the coolant level in the radiator reserve tank. If it has gone down, add coolant to the MAX mark. Put the cap back on tightly.


Main MenuTable of Contentsst 05/09/09 18:26:48 31SNC600 0230 


This indicator should never come on when the engine is running. If it starts flashing


or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible, and you should take immediate action.


Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the vehicle stopped.


1.


2.


3.


4.


Low Oil Pressure Indicator


The engine running generates the oil pressure. When the Auto Idle Stop is activated, the engine is stopped, the oil pressure is dropped, and the low oil pressure indicator does not come on.


Safely pull off the road, and shut off the engine. Turn on the hazard warning indicators.


Let the vehicle sit for a minute. Open the hood, and check the oil level (see page ). An engine very low on oil can lose pressure during cornering and other driving maneuvers.


153


If necessary, add oil to bring the level back to the full mark on the dipstick (see page


189


).


Start the engine, and watch the oil pressure indicator. If it does not go out within 10 seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving (see 237


Emergency Towing ).


on page


227


Main MenuTable of Contentsst 05/09/09 18:26:54 31SNC600 0231 


Charging System Indicator


If the charging system indicator comes on brightly when the engine is running,


the 12 volt battery is not being charged.


Immediately turn off all electrical accessories. Try not to use other electrically operated controls such as the power windows and rear window defogger. Keep the engine running; starting the engine will discharge the battery rapidly.


Go to a service station or garage where you can get technical assistance.


If the Auto Idle Stop is active for an extended period, the charging system indicator may come on. If it happens, start the engine.


The charging system indicator may also come on if the Integrated Motor Assist (IMA) battery charge drops below a desired level and the engine starts to recharge the battery.


This indicator may blink after you start the vehicle in the morning when the temperature is below 20
− °F ( 30°C). It will stop blinking when the IMA battery warms up.



228


Main MenuTable of Contentsst 05/09/09 18:27:01 31SNC600 0232 


If the indicator comes on while driving, it means one of the engine’s emissions


control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage.


If you have recently refueled your vehicle, the indicator coming on could be due to a loose or missing fuel fill cap. You will also see a ‘‘CHECK FUEL CAP’’ message on the information display. Tighten the cap until it clicks at least once (see page ). Tightening the cap will not turn the indicator off immediately; it can take several days of normal driving.


151


Malfunction Indicator Lamp


If the indicator comes on repeatedly, even though it may turn off as you continue driving, have the vehicle checked by the dealer as soon as possible.


If the battery in your vehicle has been disconnected or gone dead, these codes are erased. It takes at least three days of driving under various conditions to set the codes again.


If you keep driving with the Malf unction Indicator Lamp on, you can damage your vehicle’s emissions controls and engine. Those repairs may not be covered by your vehicle’s warranties. This indicator may also come on with the ‘‘D’’ indicator.


Readiness Code Your vehicle has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed.


To check if they are set, turn the ignition switch to the ON (II) position, without starting the engine. The malfunction indicator lamp will come on for 20 seconds. If it then goes off, the readiness codes are set. If it blinks five times, the readiness codes are not set. If possible, do not take your vehicle for a state emissions test until the readiness codes are set. Refer to Emissions Testing information (see page


State for more ).


250


229


Main MenuTable of Contentsst 05/09/09 18:27:08 31SNC600 0233 


Brake System Indicator


However, if the brake pedal does not feel normal, you should take immediate action. A problem in one part of the system’s dual circuit design will still give you braking at two wheels. You will feel the brake pedal go down much farther before the vehicle begins to slow down, and you will have to press harder on the pedal.


Slow down by shifting to a lower gear, and pull to the side of the road when it is safe. Because of the long distance needed to stop, it is hazardous to drive the vehicle. You should have it towed and repaired as soon as possible (see Towing 237


Emergency ).


on page


If you must drive the vehicle a short distance in this condition, drive slowly and carefully.


If the ABS indicator comes on with the brake system indicator, have your vehicle inspected by your dealer immediately.


If the brake system indicator (amber) comes on with the parking brake system indicator (red) with the parking brake released, there may be a malfunction with the power-assist feature. When the power-assist feature malfunctions, the brake indicator (red) comes on and a buzzer sounds for a second. The power-assist feature may stop when the brake effect is weak. Stop your vehicle immediately at a safe place and contact a dealer.


U.S.


Canada


The brake system indicator normally comes on when you turn the ignition switch to the ON (II) position and as a reminder to check the parking brake. It will stay on if you do not fully release the parking brake.


If the brake system indicator comes on while driving, the brake fluid level is probably low. Press lightly on the brake pedal to see if it feels normal. If it does, check the brake fluid level thenexttimeyoustopataservice station (see page


196


).


If the fluid level is low, take your vehicle to a dealer, and have the brake system inspected for leaks or worn brake pads.


230


Main MenuTable of Contentsst 05/09/10 14:37:07 31SNC600 0234 


INTERIOR


UNDER-HOOD (PRIMARY)


UNDER-HOOD (SECONDARY)


FUSE LABEL


The vehicle’s fuses are contained in three fuse boxes.


The interior fuse box is underneath the steering column.


TAB


The primary and secondary under- hood fuse boxes are in the engine compartment on the driver’s side.


Fuses


231


Main MenuTable of Contentsst 05/09/09 18:27:22 31SNC600 0235 


Fuses


and


Checking and Replacing Fuses If something electrical in your vehicle stops working, the first thing youshouldcheckforisablownfuse. Determine from the chart on pages or the diagram on the 235
fuse box lid, which fuses control that device. Check those fuses first, but check all the fuses before deciding that a blown fuse is the cause. Replace any blown fuses, and check if the device works.


236


FUSE


BLOWN


BLOWN


1.


Turn the ignition switch to the LOCK (0) position. Make sure the headlights and all other accessories are off.


2.


Remove the cover from the fuse box.


3.


Check each of the large fuses in the primary under-hood fuse box by looking through the top at the wire inside. Removing these fuses requires a Phillips-head screwdriver.


232


Main MenuTable of Contentsst 05/09/09 18:27:28 31SNC600 0236 


BLOWN


FUSE PULLER


4.


Check the smaller fuses in the under-hood fuse boxes and all the fuses in the interior fuse box by pulling out each one with the fuse puller provided in the primary under-hood fuse box.


5.


Look for a blown wire inside the fuse. If it is blown, replace it with one of the spare fuses of the same rating or lower. The spare fuses are provided back of the under- hood fuse cover.


Fuses


If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).


If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can.


CONTINUED


233


Main MenuTable of Contentsst 05/09/09 18:27:32 31SNC600 0237 


Fuses


Replacing a f use with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement f use with the proper rating f or the circuit, install one with a lower rating.


6.


If the replacement fuse of the same rating blows in a short time, there is probably a serious electrical problem in your vehicle. Leave the blown fuse in that circuit and have your vehicle checked by a qualified mechanic.


When the audio system is disabled, the clock setting in the audio system will be canceled. You will need to reset the clock according to the instructions in the audio system section on this owner’s manual.


234


Main MenuTable of Contentsst 05/09/09 18:27:41 31SNC600 0238 


UNDER-HOOD PRIMARY FUSE BOX


No. Amps.


Circuits Protected


UNDER-HOOD SECONDARY FUSE BOX


Fuse Locations


10
11
12
13
14
15
16
17
18
19
20
21
22
23


50 A 40 A 40 A 20 A 20 A 30 A 40 A 10 A 15 A 15 A 15 A 15 A 7.5 A − − 20 A 15 A 7.5 A 15 A 7.5 A 10 A



Headlight Main Power Window Main Booster Motor Sub Fan Motor Main Fan Motor (A/T) Rear Defogger Blower Hazard FI Sub Stop and Horn IG Coil (EX) IG Coil (IN) Oil Level Not Used Not Used IG Coil FI Main MG Clutch DBW Interior Light Back Up


If equipped


No.


Amps.


Circuits Protected


100 A 70 A 80 A 50 A 30 A 30 A


Main Fuse EPS Option Main Ignition Switch Main ABS ABS


No.


Amps.


Circuits Protected


10 A 7.5 A 15 A


IMA2
IMA1
Booster MS


235


Main MenuTable of Contentsst 05/09/09 18:27:49 31SNC600 0239 


Fuse Locations


INTERIOR FUSE BOX


No.


Amps.


Circuits Protected


17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38


10 A 20 A 15 A − 20 A (7.5 A) (7.5 A)


− 20 A 20 A −


(15 A) 15 A 20 A − 20 A 20 A − 7.5 A 10 A 7.5 A 30 A


If equipped


No.


Amps.


Circuits Protected


No.


Amps.


Circuits Protected


7.5 A 15 A 10 A 7.5 A − − − −


Power Window Fuel Pump Alternator ABS Unit Not Used Not Used Not Used Not Used


236


10
11
12
13
14
15
16


7.5 A 7.5 A 10 A 10 A 10 A 7.5 A 7.5 A 10 A


ODS METER SRS Right Headlight High Left Headlight High Small (Interior) Small (Exterior) Right Headlight Low




Left Headlight Low Headlight High Main Small (Main) Not Used Headlight Low Main (HAC) STS Not Used Door Lock Driver’s Power Window Not Used Rear ACC Socket ACC Passenger’s Power Window Not Used Right Rear Power Window Left Rear Power Window Not Used ACC Radio HAC Daytime Running Light Wiper


Main MenuTable of Contentsst 05/09/09 18:27:58 31SNC600 0240 


If your vehicle needs to be towed, call a professional towing service or organization. Never tow your vehicle with just a rope or chain. It is very dangerous.


There are two ways to tow your vehicle:



Flat-bedEquipment loads your vehicle on the back of a truck. port your vehicle.


This is the best way to trans-


The operator



The tow


Wheel-liftEquipment truck uses two pivoting arms that go under the tires (front) and lift them off the ground. The other two tires remain on the ground. acceptable way to tow your vehicle.


This is an


If, due to damage, your vehicle must be towed with the front wheels on the ground, do this:


Release the parking brake. Start the engine. Shift to D, then to N. Turn off the engine. Leave the ignition switch in the ACCESSORY (I) position so the steering wheel does not lock.


Emergency Towing


Improper towing preparation will damage the transmission. Follow the above procedure exactly. If you cannot shif t the transmission or start the engine, your vehicle must be transported with the f ront wheels of f the ground.


With the front wheels on the ground, it is best to tow the vehicle no farther than 50 miles (80 km), and keep the speed below 35 mph (55 km/h).


CONTINUED


237


Main MenuTable of Contentsst 05/09/09 18:28:01 31SNC600 0241 


Emergency Towing


Trying to lif t or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle’s weight.


The steering system can be damaged if the steering wheel is locked. Leave the ignition switch in the ACCESSORY (I) position, and make sure the steering wheel turns f reely bef ore you begin towing.


238


Main MenuTable of Contentsst 05/09/09 18:28:05 31SNC600 0242 


Technical Information


The diagrams in this section give you the dimensions and capacities of your vehicle, and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems.


Identification Numbers Specifications DOT Tire Quality Grading


................ ................................


. 240
. 242


(U.S. Vehicles)


......................


. 244


Uniform Tire Quality


Grading Treadwear Traction Temperature


.................................. ................................. ...................................... ............................. .................................


Tire Labeling


. 244
. 244
. 244
. 245
. 246


Emissions Controls ....................... The Clean Air Act ..................... Crankcase Emissions Control .................................... Evaporative Emissions Control ....................................


System


System


Onboard Refueling Vapor


. 247
. 247


. 247


. 247


Recovery


. 247
Exhaust Emissions Controls . 248
. 248


................................ ... ....................


PGM-FI System Ignition Timing Control


System


................................ Exhaust Gas Recirculation ...................


(EGR) System


Three Way Catalytic


. 248


. 248


Converter


Replacement Parts


. 248
........................... .................... . 248
.. Three Way Catalytic Converter . 249
.............. . 250
State Emissions Testing


239


Main Menust 05/09/09 18:28:10 31SNC600 0243 


Identification Numbers


Your vehicle has several identifying numbers in various places.


The vehicle identification number (VIN) is the 17-digit number your dealer uses to register your vehicle for warranty purposes. It is also necessary for licensing and insuring your vehicle. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side. It is also on the certification label attached to the driver’s doorjamb, and is stamped on the engine compartment bulkhead. The VIN is also provided in bar code on the certification label.


The VIN is also located on the engine bulkhead. Slide the cover on the engine compartment bulkhead to view the VIN. Always close the cover when finished.


240


COVER


VEHICLE IDENTIFICATION NUMBER


CERTIFICATION LABEL


Main MenuTable of Contentsst 05/09/09 18:28:15 31SNC600 0244 


The engine number is stamped into the engine block.


The transmission number is on a label on top of the transmission.


The IMA Motor Number is stamped on the motor housing.


Identification Numbers


ENGINE NUMBER


IMA MOTOR NUMBER


TRANSMISSION NUMBER


241


Main MenuTable of Contentsst 05/09/09 18:28:29 31SNC600 0245 


176.7 in (4,489 mm) 69.0 in (1,752 mm) 56.3 in (1,430 mm) 106.3 in (2,700 mm) 59.1 in (1,501 mm) 60.2 in (1,529 mm)


See the certification label attached to the driver’s doorjamb.


Water cooled 4-stroke SOHC i-VTEC


with Hybrid Electric


Capacities Fuel tank


Engine coolant Engine oil


Automatic transmission fluid Windshield washer reservoir


Change * Total Change *


Including filter Without filter


Total Change Total


Approx. 12.4 US gal (47 ) 1.255 US gal (4.75 ) 1.53 US gal (5.8 )


3.4 US qt (3.2 ) 3.2 US qt (3.0 ) 4.0 US qt (3.8 ) 3.0 US qt (2.8 ) 5.4 US qt (5.1 )


U.S. Vehicles Canada Vehicles


2.6 US qt (2.5 ) 4.8 US qt (4.5 )


2.87 x 3.15 in (73.0 x 80.0 mm)



1 :


82 cu-in (1.339 cm )


10.8


ILFR6J-11K SK20HPR-L11


(NGK)


(DENSO)



2 :


Including the coolant in the reserve tank and that remaining in the engine Reserve tank capacity: Excluding the oil remaining in the engine


0.108 US gal (0.41 )


Specifications


Dimensions Length Width Height Wheelbase Track


Front Rear


Weights Gross vehicle weight rating


Engine Type


Bore x Stroke Displacement

Loading...
x