2010 Honda Accord Sedan Owners Manual

TAB

To remove the spacer cone, squeeze the tabs on the wing bolt to disengage it from the center of the spacer cone, then pull the bolt downward.

To install the wing bolt to the spacer cone, reverse this procedure.

18.

Secure the flat tire by screwing the wing bolt back into its hole.

Loose items can fly around the interior in a crash and could seriously injure the occupants.

Store the wheel, jack, and tools securely before driving.

20.

Store the wheel cover or center cap in the trunk. Make sure it does not get scratched or damaged.

21.

Lower the trunk floor, then close the trunk lid.

22.

Your vehicle’s original tire has a tire pressure monitoring system sensor. To replace a tire, refer to Changing a Tire with TPMS page

293

).

(see

357

2010 Accord Sedan０９／０５／１８　１９：１２：０９　３１ＴＡ５６２０　０３６３　

If the Engine Won’t Start

Diagnosing why the engine won’t start falls into two areas, depending on what you hear when you turn the ignition switch to the START (III) position:

You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly.

You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.

Nothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to the START (III) position, you do not hear the normal noise of the engine trying to start. You may hear a clicking sound, a series of clicks, or nothing at all.

Check these things:

Check the transmission interlock. If you have a manual transmission, the clutch pedal must be pushed all the way to the floor or the starter will not operate. With an automatic transmission, it must be in Park or neutral.

Turn the ignition switch to the ON (II) position. Turn on the headlights, and check their brightness. If the headlights are very dim or do not come on at all, the battery is discharged. See Jump Starting

on page

360

358

Turn the ignition switch to the START (III) position. If the headlights do not dim, check the condition of the fuses. If the fuses are OK, there is probably something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified mechanic to determine the problem (see Emergency Towing on page

375

).

If the headlights dim noticeably or go out when you try to start the engine, either the battery is dis- charged or the connections are corroded. Check the condition of the battery connections (see page 347
starting the vehicle from a booster battery (see page

). You can then try jump

360

).

2010 Accord Sedan０９／０５／１８　１９：１２：１７　３１ＴＡ５６２０　０３６４　

If the Engine Won’t Start

The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to the START (III) position, but the engine does not run.

Are you using the proper starting Starting the procedure? Refer to Engine 277

on page

Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the instrument panel to blink rapidly (see page ).

77

Do you have fuel? Check the fuel gauge; the low fuel indicator may not be working.

There may be an electrical problem, such as no power to the fuel pump. Check all the fuses (see page

368

).

If you find nothing wrong, you will need a qualified technician to find the problem. See Towing on page

Emergency 375

359

2010 Accord Sedan09/07/08 21:43:44 31TA5620_365

Jump Starting

Although this seems like a simple procedure, you should take several precautions.

A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.

Keep all sparks, open flames, and smoking materials away from the battery.

You cannot start your vehicle with an automatic transmission by pushing or pulling it.

360

To jump start your vehicle:

1.

Open the hood, and check the physical condition of the battery. In very cold weather, check the condition of the electrolyte. If it seems slushy or frozen, do not try jump starting until it thaws.

If a battery sits in extreme cold, the electrolyte inside can f reeze. Attempting to jump start with a f rozen battery can cause it to rupture.

2.

Turn off all the electrical accessories: heater, A/C, audio system, lights, etc. Put the transmission in neutral (manual) or Park (automatic), and set the parking brake.

BOOSTER BATTERY

4-cylinder models

The numbers in the illustrations show you the order to connect the jumper cables.

2010 Accord Sedan０９／０５／１８　１９：１２：３５　３１ＴＡ５６２０　０３６６　

Jump Starting

V6 models

BOOSTER BATTERY

4-cylinder models with automatic transmission

4-cylinder models with manual transmission

3.

＋

) terminal on your

Connect one jumper cable to the positive ( battery. Connect the other end to the positive ( ) terminal on the ＋ booster battery.

4. 4-cylindermodels

−

Connect the second jumper cable to the negative ( ) terminal on the booster battery. Connect the other end to the engine mounting bolt (automatic) or the transmission mounting bolt (manual), as shown. Do not connect this jumper cable to any other part of the engine.

CONTINUED

361

2010 Accord Sedan０９／０５／１８　１９：１２：４３　３１ＴＡ５６２０　０３６７　

Jump Starting

Keep the ends of the jumper cables away from each other and any metal on the vehicle until everything is disconnected. Otherwise, you may cause an electrical short.

5.

6.

7.

If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle.

Start the vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact.

Once your vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from your vehicle, then from the booster battery.

V6 models

−

V6models Connect the second jumper cable to the negative ( booster battery. Connect the other end to the engine hanger as shown. Do not connect this jumper cable to any other part of the engine.

) terminal on the

362

2010 Accord Sedan09/07/08 21:43:53 31TA5620_368

The pointer of the vehicle’s temperature gauge should stay in the midrange. If it climbs to the red mark, you should determine the reason (hot day, driving up a steep hill, etc.).

If your vehicle overheats, you should take immediate action. The only indication may be the temperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood.

Driving with the temperature gauge pointer at the red mark can cause serious damage to the engine.

Steam and spray from an overheated engine can seriously scald you.

Do not open the hood if steam is coming out.

1.

Safely pull to the side of the road. Put the transmission in neutral (manual) or Park (automatic), and set the parking brake. Turn off all accessories, and turn on the hazard warning lights.

2.

If you see steam and/or spray coming from under the hood, turn off the engine. Wait until you see no more signs of steam or spray, then open the hood.

If the Engine Overheats

3.

If you do not see steam or spray, leave the engine running and watch the temperature gauge. If the high heat is due to overloading, the engine should start to cool down almost immediately. If it does, wait until the temperature gauge comes down to the midpoint, then continue driving.

4.

If the temperature gauge stays at the red mark, turn off the engine.

5.

Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you Emergency continue driving (see Towing ). 375

on page

CONTINUED

363

2010 Accord Sedan09/07/08 21:44:01 31TA5620_369

If the Engine Overheats

6.

7.

If you do not find an obvious leak, check the coolant level in the radiator reserve tank. Add coolant if the level is below the MIN mark.

If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the pointer reaches the middle of the tempera- ture gauge, or lower, before check- ing the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

364

8.

9.

Using gloves or a large heavy cloth, turn the radiator cap counterclockwise, without pushing down, to the first stop. After the pressure releases, push down on the cap, and turn it until it comes off.

’’). Add coolant to the

Start the engine, and set the temperature to maximum heat (climate control to AUTO at ‘‘ radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can.

10.

Put the radiator cap back on tightly. Run the engine, and check the temperature gauge. If it goes back to the red mark, the engine needs repair (see Towing on page

Emergency 375

).

11.

If the temperature stays normal, check the coolant level in the radiator reserve tank. If it has gone down, add coolant to the MAX mark. Put the cap back on tightly.

2010 Accord Sedan０９／０５／１８　１９：１３：１６　３１ＴＡ５６２０　０３７０　

Low Oil Pressure Indicator, Charging System Indicator

Low Oil Pressure Indicator

This indicator should never come on when the engine is running. If it starts flashing or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible, and you should take immediate action.

Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the vehicle stopped.

1.

2.

3.

4.

Safely pull off the road, and shut off the engine. Turn on the hazard warning lights.

Let the vehicle sit for a minute. Open the hood, and check the oil level (see page ). An engine very low on oil can lose pressure during cornering and other driving maneuvers.

262

If necessary, add oil to bring the level back to the full mark on the dipstick (see page

312

).

Start the engine and watch the oil pressure indicator. If it does not go out within 10 seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving (see 375

Emergency Towing ).

on page

Charging System Indicator

If the charging system indicator comes on brightly

when the engine is running, the battery is not being charged.

Immediately turn off all electrical accessories. Try not to use other electrically operated controls such as the power windows. Keep the engine running; starting the engine will discharge the battery rapidly.

Go to a service station or garage where you can get technical assistance.

365

2010 Accord Sedan０９／０５／１８　１９：１３：２６　３１ＴＡ５６２０　０３７１　

Malfunction Indicator Lamp

If this indicator comes on while driving, it means one

of the engine’s emissions control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage.

If you have recently refueled your vehicle, the indicator coming on could be due to a loose or missing fuel fill cap. Tighten the cap until it clicks at least once. Tightening the cap will not turn the indicator off immediately; it can take several days of normal driving.

366

If the indicator comes on repeatedly, even though it may go off as you continue driving, have your vehicle checked by a dealer as soon as possible.

If you keep driving with the malf unction indicator lamp on, you can damage your vehicle’s emissions controls and engine. Those repairs may not be covered by your vehicle’s warranties.

If your vehicle has an automatic transmission, the malfunction indicator lamp may also come on with the ‘‘D’’ indicator.

Readiness Codes Your vehicle has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure

these codes are set. If they are not set, the test cannot be completed.

If the battery in your vehicle has been disconnected or gone dead, these codes may be erased. It can take several days of driving under various conditions to set the codes again.

To check if they are set, turn the ignition switch to the ON (II) position, without starting the engine. The malfunction indicator lamp will come on for 20 seconds. If it then goes off, the readiness codes are set. If it blinks five times, the readiness codes are not set. If possible, do not take your vehicle for an emissions test until the readiness codes are set. Emissions Testing Refer to more information (see page

for 393

).

2010 Accord Sedan０９／０５／１８　１９：１３：３５　３１ＴＡ５６２０　０３７２　

Brake System Indicator

U.S.

Canada

The brake system indicator normally comes on when you turn the ignition switch to the ON (II) position, and as a reminder to check the parking brake. It will stay on if you do not fully release the parking brake.

If the brake system indicator comes on while driving, the brake fluid level is probably low. Press lightly on the brake pedal to see if it feels normal. If it does, check the brake fluid level the next time you stop at a service station (see page

322

).

If the fluid level is low, take your vehicle to a dealer, and have the brake system inspected for leaks or worn brake pads.

However, if the brake pedal does not feel normal, you should take immediate action. A problem in one part of the system’s dual circuit design will still give you braking at two wheels. You will feel the brake pedal go down much farther before the vehicle begins to slow down, and you will have to press harder on the pedal.

Slow down by shifting to a lower gear, and pull to the side of the road when it is safe. Because of the long distance needed to stop, it is hazardous to drive the vehicle. You should have it towed and repaired as soon as possible (see Towing 375

Emergency ).

on page

If you must drive the vehicle a short distance in this condition, drive slowly and carefully.

If the ABS indicator and the VSA system indicator come on with the brake system indicator, have your vehicle inspected by your dealer immediately.

367

2010 Accord Sedan０９／０５／１８　１９：１３：４４　３１ＴＡ５６２０　０３７３　

Fuses

INTERIOR (Driver’s side)

INTERIOR (Passenger’s side)

UNDER-HOOD

NOTCH

FUSE BOX

FUSE LABEL

The vehicle’s fuses are contained in three fuse boxes.

The driver’s side interior fuse box is under the dashboard on the driver’s side. The fuse label is attached to the side panel.

The passenger’s side interior fuse box is on the lower passenger’s side panel. To remove the fuse box lid, put your finger in the notch on the lid, and pull it upward slightly, then pull it toward you and take it out of its hinges.

TAB

The under-hood fuse box is on the driver’s side. To open it, push the tabs as shown.

368

2010 Accord Sedan０９／０５／１８　１９：１３：５５　３１ＴＡ５６２０　０３７４　

374

and

Checking and Replacing Fuses If something electrical in your vehicle stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 372 373
the fuse box lid or the fuse label, which fuse or fuses control that component. Check those fuses first, but check all the fuses before deciding that a blown fuse is not the cause. Replace any blown fuses and check if the device works.

, or the diagram on

1.

Turn the ignition switch to the LOCK (0) position. Make sure the headlights and all other accessories are off.

2.

On the under-hood and passenger’s side interior fuse boxes, remove the cover from each fuse box.

FUSE

BLOWN

BLOWN

Fuses

3.

Check each of the large fuses in the under-hood fuse box by looking at the wire inside. Removing these fuses requires a Phillips-head screwdriver.

Also check the combined fuse box in the under-hood fuse box.

CONTINUED

369

2010 Accord Sedan０９／０５／１８　１９：１４：０４　３１ＴＡ５６２０　０３７５　

Fuses

BLOWN

FUSE PULLER

4.

Check the smaller fuses in the under-hood fuse box and all the fuses in the interior fuse boxes by pulling out each one with the fuse puller provided on the back of the under-hood fuse box cover.

5.

Look for a blown wire inside the fuse. If it is blown, replace it with one of the spare fuses of the same rating or lower.

FUSE PULLER

SPARE FUSES

Your vehicle has spare fuses on the back of the under-hood fuse box cover.

370

2010 Accord Sedan０９／０５／１８　１９：１４：１０　３１ＴＡ５６２０　０３７６　

If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket).

If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate that anything is wrong. Replace the fuse with one of the correct rating as soon as you can.

Replacing a f use with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement f use with the proper rating f or the circuit, install one with a lower rating.

6.

If the replacement fuse of the same rating blows in a short time, there is probably a serious electrical problem with your vehicle. Leave the blown fuse in that circuit, and have your vehicle checked by a qualified technician.

Fuses

371

2010 Accord Sedan０９／０５／１８　１９：１４：２１　３１ＴＡ５６２０　０３７７　

Fuse Locations

UNDER-HOOD FUSE BOX

＊

＊

No. Amps. 100 A − 120 A − 40 A − − − 40 A − 30 A − (40 A) − −

−

Circuits Protected

Battery Battery Passenger’s Side Fuse Box Not Used ABS/VSA ABS/VSA Motor Passenger’s Side Fuse Box Not Used

＊

＊

No. − − − − − − − −

Amps.

− − 30 A 30 A 30 A 30 A (60 A) 30 A

Circuits Protected

Not Used Not Used Sub Fan Motor Wiper Motor Main Fan Motor Driver’s Side Light Main Driver’s Side Fuse Box Passenger’s Side Light Main

＊

＊

No. − − 10
11
12
13
14
15
16
17
18
19
19
20
21

＊

＊

Amps. (40 A) 50 A 40 A 20 A − − − 40 A 15 A 20 A − − 15 A 15 A 10 A 7.5 A 15 A 15 A − 7.5 A 7.5 A 7.5 A

Circuits Protected

Driver’s Side Fuse Box IG Main Rear Defroster Sub Fan Motor Not Used Not Used Not Used Heater Motor Hazard Horn, Stop Not Used Not Used IG Coil FI Sub Back Up Interior Lights FI Main DBW Not Used Back Up, FI ECU MG Clutch Fan Relay

372

＊ ＊

1 : 2 :

4-cylinder models V6 models

2010 Accord Sedan０９／０５／１８　１９：１４：３１　３１ＴＡ５６２０　０３７８　

INTERIOR FUSE BOX (Driver’s Side)

No.

Amps.

Circuits Protected

− − 15 A 7.5 A 7.5 A 7.5 A 15 A 7.5 A

Not Used Not Used Washer Wiper Meter ABS/VSA ACG STS

＊

No. 10
11
12

13
14
15

Amps. 20 A (10 A) 10 A 7.5 A

−

(10 A) 7.5 A

Circuits Protected

＊

Fuel Pump VB SOL SRS ODS (Occupant Detection System) Not Used ACM Daytime Running Lights

＊

No. 16
17
18
19
20
21
22
23
24
25
26
27

28
29
30
31

Amps. 7.5 A 7.5 A 7.5 A (20 A) (20 A) (20 A) 20 A 15 A 20 A 10 A (10 A) 10 A

10 A 7.5 A 10 A −

＊

If equipped

Fuse Locations

Circuits Protected

＊

＊

＊

A/C Accessory, Key, Lock Accessory Driver’s Power Seat Sliding Moonroof Driver’s Power Seat Reclining Rear Left Power Window Front Accessory Power Socket Driver’s Power Window Driver’s Side Door Lock Left Front Fog Light Left Side Small Lights (Exterior) Left Headlight High Beam TPMS Left Headlight Low Beam Not Used

＊

373

2010 Accord Sedan０９／０５／１８　１９：１４：４２　３１ＴＡ５６２０　０３７９　

Fuse Locations

INTERIOR FUSE BOX (Passenger’s Side)

Circuits Protected

＊

Not Used Not Used Lumbar Support Seat Heater Not Used Not Used Not Used

＊

No. 16
17
18
19
20
21
22

Amps.

− −

(10 A) (15 A)

− − −

＊

If equipped

Circuits Protected

＊

Right Headlight High Beam Right Side Small Lights (Exterior) Right Front Fog Light Right Headlight Low Beam Not Used Interior Lights Not Used Front Passenger’s Power Seat Reclining

＊

No. Amps. (20 A)

10
11
12

13

14
15

10 A (20 A) 15 A

20 A

−

(20 A)

＊

Circuits Protected Front Passenger’s Power Seat Sliding Right Side Door Lock Rear Right Power Window Rear Accessory Power Socket Front Passenger’s Power Window Not Used Premium AMP

＊

No.

Amps. 10 A 10 A

(10 A) 10 A − 7.5 A −

(20 A)

374

2010 Accord Sedan０９／０５／１８　１９：１４：５８　３１ＴＡ５６２０　０３８０　

If your vehicle needs to be towed, call a professional towing service or organization. Never tow your vehicle with just a rope or chain. It is very dangerous.

There are two ways to tow your vehicle:

−

Flat-bedEquipment loads your vehicle on the back of a truck. transport your vehicle.

This is the best way to

The operator

−

The tow

Wheel-liftEquipment truck uses two pivoting arms that go under the front tires and lift them off the ground. The rear tires remain on the ground. way to tow your vehicle.

This is an acceptable

If, due to damage, your vehicle must be towed with the front wheels on the ground, do this:

Manualtransmission:

Shift the transmission to neutral. Leave the ignition switch in the ACCESSORY (I) position so the steering wheel does not lock. Release the parking brake.

Automatictransmission:

Start the engine. Shift to D position and hold for 5
seconds, then to N. Turn off the engine. Leave the ignition switch in the ACCESSORY (I) position so the steering wheel does not lock. Release the parking brake.

Emergency Towing

Improper towing preparation will damage the transmission. Follow the above procedure exactly. If you cannot shif t the transmission or start the engine (automatic transmission), your vehicle must be transported with the f ront wheels of f the ground.

With the front wheels on the ground, do not tow the vehicle more than 50
miles (80 km), and keep the speed below 35 mph (55 km/h).

CONTINUED

375

2010 Accord Sedan０９／０５／１８　１９：１５：０３　３１ＴＡ５６２０　０３８１　

Emergency Towing

Trying to lif t or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle’s weight.

The steering system can be damaged if the steering wheel is locked. Leave the ignition switch in the ACCESSORY (I) position, and make sure the steering wheel turns f reely bef ore you begin towing.

376

2010 Accord Sedan09/07/08 21:45:06 31TA5620_382

Technical Information

The diagrams in this section give you the dimensions and capacities of your vehicle and the locations of the identification numbers. It also includes information you should know about your vehicle’s tires and emissions control systems.

Identification Numbers Specifications

(4-cylinder models)

................

. 378

..................

. 380

Specifications (V6 models)

...............................

. 382

DOT Tire Quality Grading

(U.S. Vehicles)

.......................... Tire Labeling ................................. Tire Pressure Monitoring System

(TPMS) Required Federal

−

. 384
. 386

Explanation

. 388
............................ Emissions Controls ....................... . 390
.. Three Way Catalytic Converter . 392
........................ . 393
Emissions Testing

377

2010 Accord Sedan０９／０５／１８　１９：１５：１３　３１ＴＡ５６２０　０３８３　

Identification Numbers

Your vehicle has several identifying numbers in various places.

The vehicle identification number (VIN) is the 17-digit number your dealer uses to register your vehicle for warranty purposes. It is also necessary for licensing and insuring your vehicle. The easiest place to find the VIN is on a plate fastened to the top of the dashboard. You can see it by looking through the windshield on the driver’s side. It is also on the certification label attached to the driver’s doorjamb, and is stamped on the engine compartment bulkhead. The VIN is also provided in bar code on the certification label.

378

VEHICLE IDENTIFICATION NUMBER (VIN)

CERTIFICATION LABEL

2010 Accord Sedan０９／０５／１８　１９：１５：１９　３１ＴＡ５６２０　０３８４　

The engine number is stamped on the front of the engine block.

The transmission number is on a label on top of the transmission.

4-cylinder models

ENGINE NUMBER

AUTOMATIC TRANSMISSION NUMBER

Identification Numbers

MANUAL TRANSMISSION NUMBER

V6 models

ENGINE NUMBER

AUTOMATIC TRANSMISSION NUMBER

379

2010 Accord Sedan09/07/08 21:45:28 31TA5620_385

Specifications (4-cylinder models)

Dimensions Length Width Height Wheelbase Track

Front/Rear

＊

1 :

LX, LX-P

＊

2 : EX, EX-L

Weights Gross vehicle weight rating

Air Conditioning Refrigerant type Charge quantity Lubricant type

Engine Type

Bore x Stroke Displacement Compression ratio Spark plugs (U.S.)

ULEV PZEV Spark plugs (Canada)

380

194.1 in (4,930 mm) 72.7 in (1,847 mm) 58.1 in (1,475 mm) 110.2 in (2,800 mm) 62.6 in (1,590 mm) ＊ 62.2 in (1,580 mm)

＊

See the certification label attached to the driver’s doorjamb.

HFC-134a (R-134a) −

14.1 15.9 oz (400 450 g)

−

ND-OIL8

Water cooled 4-stroke DOHC i-VTEC 4-cylinder

gasoline engine

3.43 x 3.9 in (87.0 x 99.0 mm)

144 cu-in (2,354 cm )

NGK: DENSO: NGK: NGK: DENSO:

10.5 : 1

ILZKR7B11S SXU22HCR11S DILZKR7A11GS ILZKR7B11S SXU22HCR11S

Seating Capacities Total Front Rear

Capacities Fuel tank

Engine coolant

Change ＊ Manual Automatic

Total

Manual Automatic

Engine oil

Change ＊

Including filter Without filter

Total Change Total Change Total

U.S. Canada

Manual trans- mission fluid Automatic transmission fluid Windshield washer reservoir 1 : ＊

Approx. 18.5 US gal (70.0 )

1.59 US gal (6.0 ) 1.56 US gal (5.9 )

1.90 US gal (7.2 ) 1.88 US gal (7.1 )

4.2 US qt (4.0 ) 4.0 US qt (3.8 ) 5.4 US qt (5.1 ) 2.0 US qt (1.9 ) 2.1 US qt (2.0 ) 2.6 US qt (2.5 ) 6.9 US qt (6.5 )

2.6 US qt (2.5 ) 4.8 US qt (4.5 )

Including the coolant in the reserve tank and that remaining in the engine Reserve tank capacity: 0.180 US gal (0.68 ) Excluding the oil remaining in the engine

＊

2 :

2010 Accord Sedan09/07/08 21:45:54 31TA5620_386

Lights Headlights

High Low

Front turn signal/parking lights Front side marker lights Rear turn signal lights Back-up lights Stop/taillights License plate lights High-mount brake light Ceiling light Spotlights Trunk light Front door courtesy lights Vanity mirror lights

Battery Capacity

12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V 12 V 14 V

12 V 12 V 12 V 12 V 12 V 12 V

− − − − − − − − − − − − − −

− − − − − −

(Amber)

60 W (HB3) 51 W (HB4) 21/5 W 3 CP 21 W 21 W 21/5 W 5 W 21 W 8 W 8 W 5 W 2 CP 1.4 W

36 AH/5 HR 38 AH/5 HR 45 AH/20 HR 47 AH/20 HR 52 AH/5 HR ＊ 65 AH/20 HR

＊

＊

PZEV engine model, and Canadian models

Specifications (4-cylinder models)

Fuses Interior

Driver’s side

Passenger’s side

See page 373 or the fuse label attached on the side panel. See page 374 or the fuse label attached to the inside of the fuse box door. See page 372 or the fuse box cover.

Under-hood

Tires Size

Pressure

Front/Rear

Spare Front/Rear

Spare

＊

P215/60R16 94H P225/50R17 93V ＊ T135/80D16 101M

30 psi (210 kPa , 2.1 kgf/cm ) 32 psi (220 kPa , 2.2 kgf/cm ) 60 psi (420 kPa , 4.2 kgf/cm )

＊

＊

＊ ＊

1 : 2 :

LX, LX-P EX, EX-L

Alignment Toe-in

Camber

Caster

Front Rear Front Rear Front

0.00 in (0.0 mm) 0.08 in (2.0 mm)

0° 1° − 3°48’

381

2010 Accord Sedan０９／０５／１８　１９：１６：３３　３１ＴＡ５６２０　０３８７　

Specifications (V6 models)

Dimensions Length Width Height Wheelbase Track

194.3 in (4,936 mm) 72.7 in (1,847 mm) 58.1 in (1,475 mm) 110.2 in (2,800 mm) 62.2 in (1,580 mm)

Front/Rear

Weights Gross vehicle weight rating

See the certification label attached to the driver’s doorjamb.

HFC-134a (R-134a) −

14.1 15.9 oz (400 450 g)

−

ND-OIL8

Water cooled 4-stroke

SOHC i-VTEC 6-cylinder (V6)

gasoline engine

3.50 x 3.66 in (89.0 x 93.0 mm)

212 cu-in (3,471 cm )

NGK: DENSO: NGK: DENSO:

10.5 : 1
ILZKR7B11
SXU22HCR11
ILZKR7B11
SXU22HCR11

Air Conditioning Refrigerant type Charge quantity Lubricant type

Engine Type

Bore x Stroke Displacement Compression ratio Spark plugs (U.S.)

Spark plugs (Canada)

382

Seating Capacities Total Front Rear

Capacities Fuel tank

Engine coolant Engine oil

Change ＊ Total Change ＊

Including filter Without filter

Total Change Total

U.S. Canada

Automatic transmission fluid Windshield washer reservoir

Approx. 18.5 US gal (70.0 ) 1.74 US gal (6.6 ) 2.27 US gal (8.6 )

4.5 US qt (4.3 ) 4.2 US qt (4.0 ) 5.3 US qt (5.0 ) 3.5 US qt (3.3 ) 7.9 US qt (7.5 )

2.6 US qt (2.5 ) 4.8 US qt (4.5 )

＊

1 :

＊

2 :

Including the coolant in the reserve tank and that remaining in the engine Reserve tank capacity: Excluding the oil remaining in the engine

0.180 US gal (0.68 )

2010 Accord Sedan09/07/08 21:46:17 31TA5620_388

Lights Headlights

High Low

＊

Front turn signal/parking lights