2010 Honda Accord Sedan Owners Manual

Tethers for CHildren) system. A child whose seat is not properly secured to the vehicle can be endangered in a crash.

2.

After installing a child

Makesurethechildseatisfirmly secured. seat, push and pull the seat forward and from side-to-side to verify that it is secure.

A child seat secured with a seat belt should be installed as firmly as possible. However, it does not need to be ‘‘rock solid.’’ Some side-to-side

movement can be expected and should not reduce the child seat’s effectiveness.

If the child seat is not secure, try installing it in a different seating position, or use a different style of child seat that can be firmly secured.

3.

Securethechildinthechildseat. Make sure the child is properly strapped in the child seat according to the child seat maker’s instructions. A child who is not properly secured in a child seat can be seriously injured in a crash.

The following pages provide guidelines on how to properly install a child seat. A forward-facing child seat is used in all examples, but the instructions are the same for rear- facing child seats.

41

2010 Accord Sedan０９／０５／１８　１８：１５：０５　３１ＴＡ５６２０　００４７　

Installing a Child Seat

Installing a Child Seat with LATCH Your vehicle is equipped with LATCH (Lower Anchors and Tethers for CHildren) at the outer rear seats.

The lower anchors are located between the seat-back and seat bottom, and are to be used only with a child seat designed for use with LATCH.

The location of each lower anchor is indicated by a small button above the anchor point.

42

BUTTON

LOWER ANCHORS

Rigid type

To install a LATCH-compatible child seat:

1.

2.

Move the seat belt buckle or tongue away from the lower anchors.

Make sure there are no objects near the anchors that could prevent a secure connection between the child seat and the anchors.

3.

Place the child seat on the vehicle seat, then attach the seat to the lower anchors according to the child seat maker’s instructions.

Some LATCH-compatible seats have a rigid-type connector as shown above.

2010 Accord Sedan０９／０５／１８　１８：１５：１４　３１ＴＡ５６２０　００４８　

Flexible type

ANCHOR

TETHER STRAP HOOK

Other LATCH-compatible seats have a flexible-type connector as shown above.

4.

Whatever type you have, follow the child seat maker’s instructions for adjusting or tightening the fit.

5.

Lift the head restraint (see page ), then route the tether strap 95
through the legs of the head restraint and over the seat-back, making sure the strap is not twisted.

6.

Attach the tether strap hook to the tether anchor, then tighten the strap as instructed by the child seat maker.

Installing a Child Seat

7.

Push and pull the child seat forward and from side-to-side to verify that it is secure.

43

2010 Accord Sedan０９／０５／１８　１８：１５：２３　３１ＴＡ５６２０　００４９　

Installing a Child Seat

Installing a Child Seat with a Lap/ Shoulder Belt When not using the LATCH system, all child seats must be secured to the vehicle with the lap part of a lap/ shoulder belt.

In addition, the lap/shoulder belts in all seating positions except the driver’s have a lockable retractor that must be activated to secure a child seat.

1.

With the child seat in the desired seating position, route the belt through the child seat according to the seat maker’s instructions, then insert the latch plate into the buckle and remove any slack from the lap portion of the belt.

2.

3.

To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops, then let the belt feed back into the retractor.

After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked, and you will need to repeat these steps.

44

2010 Accord Sedan０９／０５／１８　１８：１５：３１　３１ＴＡ５６２０　００５０　

Installing a Child Seat

To deactivate the lockable retractor and remove a child seat, unlatch the buckle, unroute the seat belt, and let the belt fully retract.

45

4.

After confirming that the belt is locked, grab the shoulder part of the belt near the buckle, and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child seat will not be secure.

To remove slack, it may help to put weight on the child seat, or push on the back of the seat while pulling up on the belt.

5.

Push and pull the child seat forward and from side-to-side to verify that it is secure enough to stay upright during normal driving maneuvers. If the child seat is not secure, unlatch the belt, allow it to retract fully, then repeat these steps.

2010 Accord Sedan０９／０５／１８　１８：１５：４３　３１ＴＡ５６２０　００５１　

Installing a Child Seat

Installing a Child Seat with a Tether

UsinganAnchor

TETHER STRAP HOOK

TETHER STRAP HOOK

TETHER ANCHORAGE POINTS

A child seat with a tether can be installed in any seating position in the back seat, using one of the anchorage points shown above.

Since a tether can provide additional security to the lap/shoulder belt installation, we recommend using a tether whenever one is required or available.

46

Outer Position

ANCHOR

Center Position

ANCHOR

3.

Tighten the strap according to the seat maker’s instructions.

1.

After properly securing the child seat (see page ), lift the head restraint, then route the tether strap through the head restraint legs.

44

2.

Lift the anchor cover, then attach the tether strap hook to the anchor, making sure the strap is not twisted.

2010 Accord Sedan09/07/08 21:34:46 31TA5620_052

When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in a back seat on a booster seat and wear the lap/ shoulder belt.

The following pages give instructions on how to check proper seat belt fit, what kind of booster seat to use if one is needed, and important precautions for a child who must sit in front.

Allowing a child age 12 or under to sit in front can result in injury or death if the passenger’s front airbag inflates.

If a child must ride in front, move the vehicle seat as far back as possible, use a booster seat if needed, have the child sit up properly and wear the seat belt properly.

Protecting Larger Children

Checking Seat Belt Fit

To determine if a lap/shoulder belt properly fits a child, have the child put on the seat belt, then ask yourself:

1.

Does the child sit all the way back against the seat?

2.

Do the child’s knees bend comfortably over the edge of the seat?

CONTINUED

47

2010 Accord Sedan０９／０５／１８　１８：１６：０４　３１ＴＡ５６２０　００５３　

Protecting Larger Children

3.

Does the shoulder belt cross between the child’s neck and arm?

Using a Booster Seat

4.

Is the lap part of the belt as low as possible, touching the child’s thighs?

5.

Will the child be able to stay seated like this for the whole trip?

If you answer yes to all these questions, the child is ready to wear the lap/shoulder belt correctly. If you answer no to any question, the child needs to ride on a booster seat.

48

A child who has outgrown a forward- facing child seat should ride in a back seat and use a booster seat until the lap/shoulder belt fits them properly without the booster.

Some states, Canadian provinces and territories also require children to use a booster seat until they reach a given age or weight (e.g., 6 years or 60 lbs). Be sure to check current laws in the states, provinces or territories where you intend to drive.

Booster seats can be high-back or low-back. Whichever style you select, make sure the booster seat meets federal safety standards (see page 40
seat maker’s instructions.

) and that you follow the booster

If a child who uses a booster seat must ride in front, move the vehicle seat as far back as possible and be sure the child is wearing the seat belt properly.

2010 Accord Sedan０９／０５／１８　１８：１６：１５　３１ＴＡ５６２０　００５４　

A child may continue using a booster seat until the tops of their ears are even with the top of the vehicle’s or booster’s seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster seat.

When Can a Larger Child Sit in Front The National Highway Traffic Safety Administration and Transport Canada recommend that all children age 12 and under be properly restrained in a back seat.

If the passenger’s front airbag inflates in a moderate to severe frontal collision, the airbag can cause serious injuries to a child who is unrestrained, improperly restrained, sitting too close to the airbag, or out of position.

A side airbag also poses risks. If any part of a larger child’s body is in the path of a deploying side airbag, the child could receive possibly serious injuries.

Protecting Larger Children

Of course, children vary widely. And while age may be one indicator of when a child can safely ride in front, there are other important factors you should consider.

PhysicalSize Physically, a child must be large enough for the lap/shoulder belt to properly fit (see pages ). If 47
the seat belt does not fit properly, with or without the child sitting on a booster seat, the child should not sit in front.

and

14

Maturity To safely ride in front, a child must be able to follow the rules, including sitting properly, and wearing the seat belt properly throughout a ride.

CONTINUED

49

2010 Accord Sedan０９／０５／１８　１８：１６：２６　３１ＴＡ５６２０　００５５　

Devices intended to

Donotputanyaccessoriesona seatbelt. improve a child’s comfort or reposition the shoulder part of a seat belt can make the belt less effective and increase the chance of serious injury in a crash.

Additional Safety Precautions

Donotletachildwearaseatbelt This could result acrosstheneck. in serious neck injuries during a crash.

This could

Donotletachildputtheshoulder partofaseatbeltbehindtheback orunderthearm. cause very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.

Twochildrenshouldneverusethe sameseatbelt. could be very seriously injured in a crash.

If they do, they

Protecting Larger Children

If you decide that a child can safely ride up front, be sure to:

Carefully read the owner’s manual, and make sure you understand all seat belt instructions and all safety information.

Move the vehicle seat to the rear- most position.

Have the child sit up straight, back against the seat, and feet on or near the floor.

Check that the child’s seat belt is properly and securely positioned.

Supervise the child. Even mature children sometimes need to be reminded to fasten the seat belts or sit properly.

50

2010 Accord Sedan09/07/08 21:34:54 31TA5620_056

Your vehicle’s exhaust contains carbon monoxide gas. Carbon monoxide should not enter the vehicle in normal driving if you maintain your vehicle properly and follow the information on this page.

Have the exhaust system inspected for leaks whenever:

The vehicle is raised for an oil change.

You notice a change in the sound of the exhaust.

The vehicle was in a collision that may have damaged the underside.

Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you.

Avoid any enclosed areas or activities that expose you to carbon monoxide.

High levels of carbon monoxide can collect rapidly in enclosed areas, such as a garage. Do not run the engine with the garage door closed. Even with the door open, run the engine only long enough to move the vehicle out of the garage.

Carbon Monoxide Hazard

With the trunk open, airflow can pull exhaust gas into your vehicle’s interior and create a hazardous condition. If you must drive with the trunk open, open all the windows and set the heating and cooling system/ climate control system as shown below.

If you must sit in your parked vehicle with the engine running, even in an unconfined area, adjust the heating and cooling system/climate control system as follows:

1. 2. 3. 4.

Select the fresh air mode. Select the Turn the fan on high speed. Set the temperature control to a comfortable setting.

mode.

51

2010 Accord Sedan０９／０５／１８　１８：１７：０３　３１ＴＡ５６２０　００５７　

Safety Labels

These labels are in the locations shown. They warn you of potential hazards that could cause serious injury or death. Read these labels carefully.

If a label comes off or becomes hard to read (except for the U.S. dashboard label which may be removed by the owner), contact your dealer for a replacement.

SUN VISORS

U.S.models

Canadianmodels

DOORJAMBS U.S.models

Canadianmodels

DASHBOARD U.S.modelsonly

RADIATOR CAP

52

2010 Accord Sedan０９／０５／１８　１８：１７：０９　３１ＴＡ５６２０　００５８　

Instruments and Controls

This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach.

Control Locations Instrument Panel Instrument Panel Indicators Gauges

........................... ............................ .......... ............................................. ....................

Information Display

. 54
. 55
. 56
. 63
. 64

Odometer Outside Temperature

.....................................

Indicator Trip Meter Check Fuel Cap Message Maintenance Minder Temperature Gauge Fuel Gauge

................................... ................................... .......... .................. ................... ..................................

. 64

. 65
. 65
. 66
. 66
. 66
. 66

Controls Near the Steering

Wheel

........................................... . 67
Windshield Wipers and Washers . 68
. 69
Turn Signals and Headlights ......... . 72
Fog Lights ........................................ . 72
Instrument Panel Brightness ........ . 73
Hazard Warning Button ................. ................. Rear Window Defogger . 74
. 75
Steering Wheel Adjustments ........ . 76
Keys and Locks ............................... . 77
Immobilizer System ........................ ................................ Ignition Switch . 78
...................................... . 79
Door Locks Auto Door Locking/Unlocking . 80
. 86
.............. Childproof Door Locks . 86
....................... ................................................ . 90
. 91
........

Remote Transmitter Trunk

Emergency Trunk Opener

Seats

................................................. . 92
Front Seat Power Adjustments . 92
Front Seat Manual

Adjustments

............................

. 93

Driver’s Seat Manual Height

Adjustment

Head Restraints Folding Rear Seat Armrests Seat Heaters Mirrors Power Windows Moonroof Parking Brake Interior Convenience Items

.............................. .......................... ....................... ...................................... .................................. ........................................... ............................ ....................................... ............................... ......... ..................... ........ ............. .................................. .................... .................................. ............................ .................................. .......................... ...............................

Beverage Holders Accessory Power Sockets Console Compartment Glove Box Sunglasses Holder Sun Visors Vanity Mirror Coat Hook Center Pockets

. 94
. 94
. 97
. 98
. 100
. 101
. 103
. 107
. 109
. 110
. 111
. 111
. 112
. 113
. 113
. 114
. 115
. 115
. 115
. 116

Interior Lights

53

2010 Accord Sedan０９／０５／１８　１８：１７：１７　３１ＴＡ５６２０　００５９　

Control Locations

INSTRUMENT PANEL INDICATORS (P.55) GAUGES

(P.63)

MIRROR CONTROLS (P.102)

POWER DOOR LOCK MASTER SWITCH (P.79)

POWER WINDOW SWITCHES (P.103)

HOOD RELEASE HANDLE (P.260)

(P.90)

TRUNK RELEASE LEVER FUEL FILL DOOR RELEASE LEVER (P.257)

MOONROOF SWITCH (P.107)

＊

HOMELINK BUTTONS (P.226)

＊

MIRROR CONTROL AUTO BUTTON ＊ (P.101) CLOCK COMPASS

(P.219)

(P.214)

＊

HEATING/COOLING CONTROLS (P.120) CLIMATE CONTROL SYSTEM (P.125)

AUDIO SYSTEM (P.133)

MANUAL TRANSMISSION (P.278) AUTOMATIC TRANSMISSION (P.280)

ACCESSORY POWER SOCKETS (P.111)

AUXILIARY INPUT JACK (P.212)

U.S. EX-L V6 model without navigation system is shown.

If equipped

＊ 54

2010 Accord Sedan０９／０５／１８　１８：１７：２６　３１ＴＡ５６２０　００６０　

Instrument Panel

MAINTENANCE MINDER INDICATOR

(P.62)

DAYTIME RUNNING LIGHTS INDICATOR

(P.61)

DOOR AND TRUNK OPEN INDICATOR (P.60)

SECURITY SYSTEM INDICATOR

＊

(P.61)

VSA ACTIVATION INDICATOR

(P.58)

VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR (P.58) IMMOBILIZER SYSTEM INDICATOR

(P.62)

LOW TIRE PRESSURE INDICATOR (P.59)

PARKING BRAKE AND BRAKE SYSTEM INDICATOR

(P.57)

LIGHTS ON INDICATOR

(P.60)

FOG LIGHT INDICATOR

＊

(P.62)

CRUISE CONTROL MAIN INDICATOR (P.62)

CRUISE CONTROL INDICATOR (P.62)

TIRE PRESSURE MONITORING SYSTEM (TPMS) INDICATOR (P.59) MALFUNCTION INDICATOR LAMP

(P.56, 366)

LOW OIL PRESSURE INDICATOR

(P.56, 365)

CHARGING SYSTEM INDICATOR

(P.56, 365)

SIDE AIRBAG OFF INDICATOR (P.57)

SEAT BELT REMINDER INDICATOR

(P.56)

＊

: If equipped

FUEL ECONOMY INDICATOR

＊

(P.59)

HIGH BEAM INDICATOR

(P.61)

LOW FUEL INDICATOR (P.61)

ANTI-LOCK BRAKE SYSTEM (ABS) INDICATOR

(P.58)

SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR

(P.57)

The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.

55

2010 Accord Sedan０９／０５／１８　１８：１７：３９　３１ＴＡ５６２０　００６１　

If your front passenger does not fasten their seat belt, the indicator comes on about 6 seconds after the ignition switch is turned to the ON (II) position.

If either of you do not fasten your seat belt while driving, the beeper will sound and the indicator will flash again at regular intervals. For more information, see page

18

Instrument Panel Indicators

The instrument panel has many indicators to give you important information about your vehicle.

Seat Belt Reminder Indicator

This indicator comes on when you turn the ignition switch to the ON (II) position. It reminds you and your passengers to fasten your seat belts. A beeper also sounds if you have not fastened your seat belt.

If you turn the ignition switch to the ON (II) position before fastening your seat belt, the beeper sounds and the indicator flashes. If you do not fasten your seat belt before the beeper stops, the indicator stops flashing but remains on.

56

Low Oil Pressure Indicator

The engine can be severely damaged if this indicator flashes or stays on when the engine is running. For more information, see page 365

Charging System Indicator

If this indicator comes on when the engine is running, the battery is not being charged. For more information, see page

365

Malfunction Indicator Lamp 366

See page

2010 Accord Sedan０９／０５／１８　１８：１７：５３　３１ＴＡ５６２０　００６２　

Instrument Panel Indicators

Supplemental Restraint System Indicator

This indicator comes on briefly when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates a potential problem with your front airbags. This indicator will also alert you to a potential problem with your side airbags, passenger’s side airbag cutoff system, side curtain airbags, automatic seat belt tensioners, driver’s seat position sensor, or the front passenger’s weight sensors. For more information, see page 29

Parking Brake and Brake System Indicator

U.S.

Canada

This indicator has two functions:

1.

2.

It comes on when you turn the ignition switch to the ON (II) position. It is a reminder to check the parking brake. A beeper sounds if you drive with the parking brake not fully released. Driving with the parking brake not fully released can damage the brakes and tires.

If it remains lit after you fully release the parking brake while the engine is running, or if it comes on while driving, there could be a problem with the brake system. For more information, see page

367

Side Airbag Off Indicator

U.S.

Canada

This indicator comes on briefly when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. For more information, see page

30

57

2010 Accord Sedan０９／０５／１８　１８：１８：０６　３１ＴＡ５６２０　００６３　

Instrument Panel Indicators

Anti-lock Brake System (ABS) Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on at any other time, there is a problem with the ABS. If this happens, have your vehicle checked at a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function. For more information, see page

287

Vehicle Stability Assist (VSA) System Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If it comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the VSA system. Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. See page for more information on the 289
VSA system.

VSA Activation Indicator

This indicator has three functions:

1.

2.

3.

It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.

It flashes when VSA is active (see page

289

).

It comes on along with the VSA system indicator if there is a problem with the VSA system.

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. For more information, see page

289

58

2010 Accord Sedan０９／０５／１８　１８：１８：１８　３１ＴＡ５６２０　００６４　

Low Tire Pressure Indicator

This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.

If this happens, pull to the side of the road when it is safe, check which tire has lost the pressure, and determine the cause. If it is because of a flat tire, replace the flat tire with the compact spare (see page ), and have the flat tire repaired as soon as possible. If two or more tires are underinflated, call a professional towing service (see page information, see page

). For more 291

353

375

Instrument Panel Indicators

Fuel Economy Indicator

V6models While the engine is operating in its most economical range, this indicator may come on and stay on.

Tire Pressure Monitoring System (TPMS) Indicator This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.

If this indicator comes on and stays on at any other time, or if it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the TPMS. With this indicator on, the low tire pressure indicator will not come on when a tire loses pressure. Take the vehicle to your dealer to have the system checked.

59

2010 Accord Sedan０９／０５／１８　１８：１８：２９　３１ＴＡ５６２０　００６５　

Instrument Panel Indicators

Turn Signal and Hazard Warning Indicators

The left or right turn signal indicator blinks when you signal a lane change or turn. If an indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see pages ). and Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.

328

330

When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.

60

Lights On Indicator

Door and Trunk Open Indicator

or

This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the position. If you turn the

ignition switch to the ACCESSORY (I) or the LOCK (0) position without turning off the light switch, this indicator will remain on. A reminder chime will also sound when you open the driver’s door.

EX-LandEX-LV6
This indicator will also come on when the light switch is in AUTO and the lights turn on automatically.

DRIVER’S DOOR OPEN INDICATOR

TRUNK OPEN INDICATOR

The appropriate indicator comes on if the trunk or any door is not closed tightly.

All the indicators come on for a few seconds when you turn the ignition switch to the ON (II) position.

2010 Accord Sedan０９／０５／１８　１８：１８：４２　３１ＴＡ５６２０　００６６　

Low Fuel Indicator

Security System Indicator

High Beam Indicator

Instrument Panel Indicators

This indicator comes on as a reminder that you must refuel soon. When the indicator comes on, there are about 2.8 U.S. gal (10.5 ) of fuel remaining in the tank.

When the needle reaches E, there is a very small amount of fuel in the tank.

SECURITY SYSTEM INDICATOR

This indicator comes on with the high beam headlights. For more information, see page

69

This indicator also comes on with reduced brightness when the daytime running lights (DRL) are on (see page

71

).

Ifequipped This indicator comes on when the security system is set. See page 217
for more information on the security system.

Daytime Running Lights Indicator

If this indicator comes on when you turn the ignition switch to the ON (II) position and release the parking brake, it means there is a problem with the DRL. There may also be a problem with the high beam headlights. Have your vehicle checked by your dealer.

61

2010 Accord Sedan０９／０５／１８　１８：１９：０１　３１ＴＡ５６２０　００６７　

Instrument Panel Indicators

Maintenance Minder Indicator

This indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. It reminds you that it is time to take your vehicle in for scheduled maintenance. The maintenance main items and sub items will be displayed in the information display. See page 303
maintenance minder.

for more information on the

This indicator goes off when your dealer resets it after completing the required maintenance service.

Immobilizer System Indicator

This indicator comes on briefly when you turn the ignition switch to the ON (II) position. It will then go off if you have inserted a properly coded ignition key. If it is not a properly coded key, the indicator will blink, and the engine’s fuel system will be disabled (see page

77

).

Washer Level Indicator

Canadianmodelsonly This indicator comes on when the washer fluid level is low. Add washer fluid when you see this indicator (see page

318

).

Cruise Control Main Indicator

This indicator comes on when you turn on the cruise control system by pressing the CRUISE button (see page

223

).

Cruise Control Indicator

This indicator comes on when you set the cruise control. See page 223
cruise control.

for information on operating the

Fog Light Indicator

Ifequipped This indicator comes on when you turn on the fog lights. For more information, see page

72

62

2010 Accord Sedan０９／０５／１８　１８：１９：０９　３１ＴＡ５６２０　００６８　

TACHOMETER

SPEEDOMETER

TEMPERATURE GAUGE

FUEL GAUGE

OUTSIDE TEMPERATURE INDICATOR

＊

TRIP METER

SELECT/RESET KNOB

ODOMETER/CHECK FUEL CAP MESSAGE

U.S. model is shown.

＊ If equipped

INFORMATION DISPLAY

Gauges

63

2010 Accord Sedan０９／０５／１８　１８：１９：１６　３１ＴＡ５６２０　００６９　

Gauges

INFORMATION DISPLAY

ODOMETER

TRIP METER A

ENGINE OIL LIFE

OUTSIDE TEMPERATURE INDICATOR

TRIP METER B

: Press the select/reset knob.

U.S. model with outside temperature indicator is shown.

Information Display The information display shows the odometer, trip meter, engine oil life, outside temperature (if equipped), and maintenance item code(s).

To switch the display, press and release the select/reset knob repeatedly. When you turn the ignition switch to the ON (II) position, your last selection is displayed.

64

Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.

2010 Accord Sedan０９／０５／１８　１８：１９：３１　３１ＴＡ５６２０　００７０　

Outside Temperature Indicator Ifequipped This indicator displays the outside temperature in Fahrenheit (U.S. models) or Celsius (Canadian models). To see the outside temperature, press and release the select/reset knob until the temperature is displayed.

The temperature sensor is in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your speed is under 19 mph (30 km/h).

The sensor delays the display update until it reaches the correct outside temperature. This may take several minutes.

If the outside temperature is

incorrectly displayed, you can adjust it up to 3°C ± in Canadian models) warmer or cooler.

5°F in U.S. models (

±

The temperature must be

NOTE: stabilized before doing this procedure.

Select the outside temperature display, then press and hold the select/reset knob for 10 seconds. The following sequence will appear for 1 second each: 0, 1, 2, 3, 4, 5, 5, − 1, 0 (U.S.) or 0, 1, 2, − − − − 3,

4, 2, − − −

1, 0 (Canada).

3,

3,

2,

When the temperature reaches the desired value, release the select/ reset knob. You should see the new outside temperature displayed.

In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.

Gauges

Trip Meter The trip meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it.

There are two trip meters: Trip A and Trip B. Switch between these displays by pressing the select/reset knob repeatedly.

Each trip meter works independently, so you can keep track of two different distances.

When you turn the ignition switch to the ON (II) position, your last selection is displayed.

To reset a trip meter, display it, and then press and hold the select/reset knob until the number resets to ‘‘0.0’’.

65

2010 Accord Sedan０９／０５／１８　１８：１９：４２　３１ＴＡ５６２０　００７１　

Gauges

Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. Turn to page for instructions and precautions on checking the engine cooling system.

363

Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.

Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.

Check Fuel Cap Message If your fuel fill cap is loose or missing, a ‘‘CHECK FUEL CAP’’ message appears on the information display after you start the engine. For more information, see page

258

Maintenance Minder The information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving. Refer to page more information.

303

for

66

2010 Accord Sedan０９／０５／１８　１８：１９：４９　３１ＴＡ５６２０　００７２　

HEADLIGHT/TURN SIGNALS/ FOG LIGHTS

(P.69, 72)

＊

REMOTE AUDIO CONTROLS (P.211)

VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P.290)

BLUETOOTH HANDSFREELINK VOICE CONTROL BUTTONS (P.230)

＊

NAVIGATION SYSTEM VOICE CONTROL BUTTONS

＊

Controls Near the Steering Wheel

INSTRUMENT PANEL BRIGHTNESS

(P.72)

WINDSHIELD WIPERS/ WASHERS

(P.68)

PASSENGER AIRBAG OFF INDICATOR (P.30)

HAZARD WARNING BUTTON (P.73) INTERFACE DIAL ＊ (P.174)

HORN

＊

CRUISE CONTROL BUTTONS (P.223)

STEERING WHEEL ADJUSTMENTS

(P.75)

REAR WINDOW DEFOGGER/ HEATED MIRROR BUTTON ＊ (P.74, 102)

SEAT HEATER SWITCHES (P.100)

＊

＊ ＊ ＊

1 : 2 : 3 :

To use the horn, press the center pad of the steering wheel. If equipped Only on vehicles equipped with navigation system, refer to the navigation system manual.

67

2010 Accord Sedan０９／０５／１８　１８：２０：０２　３１ＴＡ５６２０　００７３　

Windshield Wipers and Washers

Push the right lever up or down to select a position.

MIST The wipers run at high speed until you release the lever.

−

OFF

−

The wipers are not activated.

−

INT The length of the wipe interval is varied automatically according to vehicle’s speed.

Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( position), the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h).

Windshield Wipers

ADJUSTMENT RING

1. 2. 3. 4. 5. 6.

MIST OFF INT LO Low speed HI High speed Windshield washers

Intermittent

− − −

68

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

−

Pull the

Windshield Washer wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete a few more sweeps after you release the lever.

2010 Accord Sedan０９／０５／１８　１８：２０：１３　３１ＴＡ５６２０　００７４　

−

Turn Signal Push down on the left lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever and hold it. The lever will return to the center when you release it or complete a turn.

EX-L V6 model is shown.

1. 2. 3. 4. 5. 6. 7. 8. 9.

＊

Turn signal Off Parking and indicator lights AUTO Headlights on High beams Flash high beams Fog lights off Fog lights on

＊

＊

−

Turning the switch to

’’ position turns on the

Headlights the ‘‘ parking lights, taillights, instrument panel lights, side-marker lights, and rear license plate lights.

Turning the switch to the ‘‘ position turns on the headlights.

’’

If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.

Turn Signals and Headlights

When the light switch is in either of these positions, the lights on indicator comes on as a reminder.

This indicator stays on if you leave the lights on and turn the ignition switch to the ACCESSORY (I) or LOCK (0) position.

−

High Beams To switch from low beams to high beams, push the left lever forward until you hear a click. The blue high beam indicator will come on (see page ). Pull it back to return to low beams. To flash the high beams, pull the lever back lightly, then release it. The high beams stay on as long as you hold the lever back.

61

＊

If equipped

69

2010 Accord Sedan０９／０５／１８　１８：２０：２１　３１ＴＡ５６２０　００７５　

Turn Signals and Headlights

Even with the automatic lighting feature turned on, we recommend that you turn on the lights manually when driving at night or in a dense fog, or when you enter dark areas such as long tunnels or parking facilities.

Do not leave the light switch in AUTO if you will not be driving the vehicle for an extended period (a week or more). You should also turn off the lights if you plan to leave the engine idling or off for a long time.

LIGHT SENSOR

The automatic lighting feature is controlled by a sensor located on top of the dashboard. Do not cover this sensor or spill liquids on it.

−

The automatic lighting

EX-LandEX-LV6
AUTO feature turns on the headlights and all other exterior lights, when it senses low ambient light.

To turn on automatic lighting, turn the light switch to AUTO. The lights will come on automatically when the outside light level becomes low (at dusk, for example). The lights on indicator comes on as a reminder. The lights and indicator will turn off automatically when the system senses high ambient light.

The lights will remain on when you turn off the ignition switch. They will turn off automatically when you remove the key and open the driver’s door. To turn them on again, either turn the ignition switch to the ON (II) position or turn the light switch to the

position.

70

2010 Accord Sedan０９／０５／１８　１８：２０：３１　３１ＴＡ５６２０　００７６　

Automatic Lighting Off Feature This feature turns off the headlights, all other exterior lights, and the instrument panel lights within 15
seconds after you remove the key and close the driver’s door.