2003 Honda Accord Sedan Owners Manual

controls to maximum.

To rapidly remove exterior frost or ice from the windshield (on very cold days), first select the Recirculation mode. Once the windshield is clear, select the Fresh Air mode to avoid fogging the windows.

118

Comfort and Convenience Features

Main MenuTable of Contentsst０２／０７／２３　２２：０７：５４　３１ＳＤＡ６００　０１２２　

Climate Control System

CENTER VENTS

SIDE VENT

TABS

TAB

To adjust the air flow from the center vent, move the tab up-and- down and side-to-side.

The side vents can be opened and closed with the dials underneath them.

Open

Close

On4-cylinderEXmodelswithlether interiorandEX-V6modelsonly The automatic climate control system in your Honda picks the proper combination of air condi- tioning, heating, and ventilation to maintain the interior temperature you select. The system also adjusts the fan speed and air flow levels.

The direction of air flow from the vents in the center and each side of the dashboard is adjustable.

The climate control system draws air through the exterior vents at the bottom of the windshield. Keep these vents clear of leaves and other debris.

For the climate control system to provide heating and cooling, the engine must be running.

CONTINUED

Comfort and Convenience Features 119

Main MenuTable of Contentsst０２／０７／２３　２２：０７：５９　３１ＳＤＡ６００　０１２３　

Climate Control System

120

Comfort and Convenience Features

Main MenuTable of Contentsst０２／０７／２３　２２：０８：１１　３１ＳＤＡ６００　０１２４　

WithoutNavigationSystem Fully-automatic Operation To put the Automatic Climate Control in fully-automatic mode, press the AUTO button, then set the desired temperature by turning the driver’s temperature control dial. You will see AUTO in the system’s display.

The system automatically selects the proper mix of conditioned and/or heated air that will, as quickly as possible, raise or lower the interior temperature from its current level to the set temperature.

When you set the temperature to its lower limit ‘‘ ’’ or its upper limit ‘‘ ’’, the system runs at full cooling or heating only. It does not regulate the interior temperature.

Climate Control System

TEMPERATURE DISPLAY

PASSENGER’S SIDE TEMPERATURE CONTROL DIAL

DRIVER’S SIDE TEMPERATURE CONTROL DIAL

FAN CONTROL BUTTONS

AUTO BUTTON

OFF BUTTON

RECIRCULATION BUTTON

In cold weather, the fan will not come on automatically until the car has been driven for a short time and the heater starts to develop warm air.

Pressing the OFF button shuts the climate control system completely off. Keep the system completely off only for short periods. To keep stale air and mustiness from collecting, you should have the fan running at all times.

Comfort and Convenience Features

121

Main MenuTable of Contentsst０２／０７／２３　２２：０８：１９　３１ＳＤＡ６００　０１２５　

DRIVER’S SIDE TEMPERATURE CONTROL DIAL

AIR CONDITIONING (A/C) BUTTON

PASSENGER’S SIDE TEMPERATURE CONTROL DIAL

RECIRCULATION BUTTON

Climate Control System

Semi-automatic Operation You can manually select various functions of the Climate Control system when it is in fully automatic mode. All other features remain automatically controlled. Making any manual selection causes the word AUTO in the display to go out.

AirConditioning(A/C)Button Press the A/C button to turn the air conditioning on and off. You will see A/C ON or A/C OFF in the display.

When you turn the A/C off, the sys- tem cannot regulate the inside tem- perature if you set the dial below the outside temperature. With the A/C off, use the temperature control dial to adjust the temperature of the air flow to a comfortable setting.

122

Comfort and Convenience Features

Main MenuTable of Contentsst０２／０７／２３　２２：０８：３０　３１ＳＤＡ６００　０１２６　

RecirculationButton This button controls the source of air going into the system. When the indicator above this button is lit, air from the car’s interior is sent through the system again (Recircula- tion mode). When the indicator is off, air is brought in from outside the car (Fresh Air mode). You can, for example, manually put the system in recirculation mode when driving through an area of smoke or fumes.

Climate Control System

FAN CONTROL BUTTONS

MODE BUTTON

FanControlButtons You can manually select the fan speed by pressing the fan control buttons: speed, or speed.

to increase the fan’s to decrease the fan’s

▲ ▼

ModeButton Use the MODE button to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes; you can turn it off with the dial below each vent. Each time you press the MODE button, the display shows the mode selected. Press the button four times to see all

RECIRCULATION BUTTON

the modes.

CONTINUED

Comfort and Convenience Features 123

Main MenuTable of Contentsst０２／０７／２３　２２：０８：４０　３１ＳＤＡ６００　０１２７　

Climate Control System

The main air flow is divided

between the floor vents and de- froster vents at the base of the wind- shield.

The main air flow comes

from the floor vents.

The main air flow is divided

between the dashboard vents and the floor vents.

The main air flow comes

from the dashboard vents.

124

Comfort and Convenience Features

Main MenuTable of Contentsst０２／０７／２３　２２：０８：４９　３１ＳＤＡ６００　０１２８　

Climate Control System

The button directs the main air flow to the windshield for faster defrosting. It also overrides any MODE selection you may have made.

, the A/C

When you select turns on automatically and the system selects Fresh Air mode. For faster defrosting, manually set the fan speed to high. You can also increase air flow to the windshield by closing the side vents in the dashboard.

When you turn off by pressing the button again, the system returns to its former settings.

RearWindowDefoggerButton This button turns the rear window 72
). defogger on and off (see page

DRIVER’S SIDE TEMPERATURE CONTROL DIAL

DUAL BUTTON

PASSENGER’S SIDE TEMPERATURE CONTROL DIAL

REAR WINDOW DEFOGGER BUTTON

Comfort and Convenience Features

125

Main MenuTable of Contentsst０２／０７／２３　２２：０９：００　３１ＳＤＡ６００　０１２９　

Climate Control System

Dual Temperature Control Your car is equipped with two temperature control dials, one for the driver, and one for the passenger. The driver’s side and the passenger’s side can be controlled independently by adjusting these dials when the green indicator in the DUAL button is lit.

button, and the set

Temperature Control Dials Push the fan, the A/C, the AUTO, or the temperatures appear in the display. When the indicator in the DUAL button is off, you can adjust both sides to the same temperature by turning the driver’s control dial.

126

Comfort and Convenience Features

DRIVER’S SIDE

PASSENGER’S SIDE

To set the driver’s side temperature to a different value than the passenger’s, press the DUAL button, then turn the driver’s control dial. To set the passenger’s side to a different value than the driver’s side, turn the passenger’s control dial (see page passenger’s side without pressing the DUAL button first.

). You can adjust the

125

Main MenuTable of Contentsst０２／０７／２３　２２：０９：１１　３１ＳＤＡ６００　０１３０　

WithNavigationSystem Fully-automatic Operation To put the Automatic Climate Control in fully-automatic mode, press the AUTO button. The indicator in the button will light. Then set the desired temperature by pressing the temperature buttons: ▲ to raise the temperature above the displayed value, or to lower the temperature.

▼

The system automatically selects the proper mix of conditioned and/or heated air that will, as quickly as possible, raise or lower the interior temperature from its current level to the set temperature.

When you set the temperature to its lower limit ‘‘ ’’ or its upper limit ‘‘ ’’, the system runs at full cooling or heating only. It does not regulate the interior temperature.

Climate Control System

TEMPERATURE DISPLAY

OFF BUTTON AUTO BUTTON

RECIRCULATION BUTTON

DRIVER’S SIDE TEMPERATURE CONTROL BUTTONS

In cold weather, the fan will not come on automatically until the car has been driven for a short time and the heater starts to develop warm air.

PASSENGER’S SIDE TEMPERATURE CONTROL BUTTONS

Pressing the OFF button shuts the climate control system completely off. Keep the system completely off only for short periods. To keep stale air and mustiness from collecting, you should have the fan running at all times.

Comfort and Convenience Features

127

Main MenuTable of Contentsst０２／０７／２３　２２：０９：２１　３１ＳＤＡ６００　０１３１　

Climate Control System

Manual Operation You can manually select various functions of the Climate Control system when it is in fully automatic mode. All other features remain automatically controlled. Some of these functions appear in the A/C display. Press the A/C button next to the display to show these functions. Making any manual selection causes the indicator in the AUTO button to go out.

AirConditioning(A/C)Icons Touching ‘‘ON’’ or ‘‘OFF’’ in the display turns the air conditioning on and off. You will see A/C ON or A/C OFF in the display. When you turn the A/C off, the sys- tem cannot regulate the inside tem- perature if you set the temperature control buttons below the outside temperature. With the A/C off, use the temperature control buttons to adjust the temperature of the air flow to a comfortable setting.

128

Comfort and Convenience Features

DRIVER’S SIDE TEMPERATURE DISPLAY

PASSENGER’S SIDE TEMPERATURE DISPLAY

AIR CONDITIONING (A/C) ICONS

A/C BUTTON MODE ICONS

FAN CONTROL ICONS

Main MenuTable of Contentsst０２／０７／２３　２２：０９：３５　３１ＳＤＡ６００　０１３２　

Climate Control System

ModeIcons Use the MODE icons in the A/C display to select the vents the air flows from. Some air will flow from the dashboard corner vents and the side vents in all modes.

The main air flow is divided

between the floor vents and de- froster vents at the base of the wind- shield.

The main air flow comes

from the floor vents.

The main air flow is divided

between the dashboard vents and the floor vents.

The main air flow comes

from the dashboard vents.

CONTINUED

Comfort and Convenience Features

129

Main MenuTable of Contentsst０２／０７／２３　２２：０９：４３　３１ＳＤＡ６００　０１３３　

Climate Control System

FanControlIcons You can manually select the fan speed by touching any of the fan control icons on the display.

RECIRCULATION BUTTON

RecirculationButton This button controls the source of air going into the system. When the indicator in this button is lit, air from the car’s interior is sent through the system again (Recirculation mode). When the indicator is off, air is brought in from outside the car (Fresh Air mode).

You can, for example, manually put the system in recirculation mode when driving through an area of smoke or fumes.

130

Comfort and Convenience Features

Main MenuTable of Contentsst０２／０７／２３　２２：０９：５３　３１ＳＤＡ６００　０１３４　

Climate Control System

The button directs the main air flow to the windshield for faster defrosting. It also overrides any MODE selection you may have made.

, the A/C

When you select turns on automatically and the system selects Fresh Air mode. For faster defrosting, manually set the fan speed to high. You can also increase air flow to the windshield by closing the side vents in the dashboard.

When you turn off by pressing the button again, the system returns to its former settings.

RearWindowDefoggerButton This button turns the rear window 72
defogger on and off (see page

).

DRIVER’S SIDE TEMPERATURE CONTROL BUTTONS

PASSENGER’S SIDE TEMPERATURE CONTROL BUTTONS REAR WINDOW DEFOGGER BUTTON

DUAL BUTTON

Comfort and Convenience Features

131

Main MenuTable of Contentsst０２／０７／２３　２２：１０：０４　３１ＳＤＡ６００　０１３５　

Climate Control System

Dual Temperature Control Your car has four temperature control buttons on the climate control panel, two for the driver and two for the passenger. The driver’s and passenger’s sides can be controlled independently by pushing these buttons when the green indicator in the DUAL button is lit.

DRIVER’S SIDE

PASSENGER’S SIDE

TemperatureControlButtons Push AUTO or and the set temperatures appear in the display. When the indicator in the DUAL button is off, you can adjust both sides to the same temperature by pressing the driver’s side.

buttons on the

▲ ▼

or

132

Comfort and Convenience Features

or

▲ ▼

buttons on

To set the driver’s side temperature to a different value than the passenger’s, press the DUAL button, then press the the driver’s side. To set the passenger’s side to a different value than the driver’s, press the ▲ ▼ buttons on the passenger’s side. You can adjust the passenger’s side without pressing the DUAL button first.

or

When you set the temperature to its lower limit or its upper limit, it will be displayed as ‘‘ ’’ or ‘‘ ’’.

Main MenuTable of Contentsst０２／０７／２３　２２：１０：１１　３１ＳＤＡ６００　０１３６　

Sunlight Sensor/Temperature Sensor

SUNLIGHT SENSOR

TEMPERATURE SENSOR

Climate Control System

The climate control system has two sensors. A sunlight sensor is located in the top of the dashboard and a temperature sensor is next to the steering column. Do not cover the sensors or spill any liquid on them.

Comfort and Convenience Features

133

Main MenuTable of Contentsst０２／０７／２３　２２：１０：２２　３１ＳＤＡ６００　０１３７　

Audio System

AM/FM/CD Audio System DXandLXmodels Your Honda’s audio system provides clear reception on both AM and FM bands, while the preset bars allow you to easily select your favorite stations.

Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pushing the PWR/ VOL knob or the AM/FM button. Adjust the volume by turning the same knob.

134

Comfort and Convenience Features

STEREO INDICATOR

SEEK BAR

SCAN BUTTON

TUNE BAR

PRESET BARS

PWR/VOL KNOB

The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM/FM button. On the FM band, ST will be displayed if the station is broadcast- ing in stereo. Stereo reproduction on AM is not available.

You can use any of five methods to find radio stations on the selected band: TUNE, SEEK, SCAN, AUTO SELECT, and the preset bars.

Main MenuTable of Contentsst０２／０７／２３　２２：１０：３０　３１ＳＤＡ６００　０１３８　

Audio System

−

Use the TUNE bar to tune

TUNE the radio to a desired frequency. Press the to a higher frequency, and the

side of the bar to tune

side to tune to a lower

frequency. The frequency numbers will start to change rapidly. Release the bar when the display reaches the desired frequency. To change the frequency in small increments, press and release the TUNE bar quickly.

−

The SEEK function

SEEK searches the band for a station with a strong signal. To activate it, press the SEEK bar on either the or , then release it. Depending on

which side you press, the system scans upward or downward from the current frequency. It stops when it finds a station with a strong signal.

−

The SCAN function

SCAN samples all the stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. You will see SCAN in the display. The system will scan up the band for a station with a strong signal. When it finds one, it will stop and play that station for approximately five seconds. If you do nothing, the system will then scan for the next strong station and play that for five seconds. When it plays a station that you want to continue listening to, press the SCAN button again.

CONTINUED

Comfort and Convenience Features 135

Main MenuTable of Contentsst０２／０７／２３　２２：１０：４１　３１ＳＤＡ６００　０１３９　

Audio System

−

You can store the

Preset frequencies of your favorite radio stations in the three preset bars. Each side of the bars (1
6) will store one frequency on the AM band, and two frequencies on the FM band.

−

To store a frequency:

1.

2.

3.

Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each preset bar.

Use the TUNE, SEEK, or SCAN function to tune the radio to a desired station.

Pick the preset number (1
6) you want for that station. Press the left or right side of the bar and hold it until you hear a beep.

−

4.

Repeat steps 1 to 3 to store a total of six stations on AM and twelve on FM.

136

Comfort and Convenience Features

SCAN BUTTON A. SEL BUTTON TUNE BAR

PRESET BARS

AM/FM BUTTON

SEEK/SKIP BAR

PWR/VOL KNOB

Once a station’s frequency is stored, simply press and release the left or right side of the proper preset bar to tune to it.

The preset frequencies will be lost if your car’s battery goes dead, is disconnected, or the radio fuse is removed.

Main MenuTable of Contentsst０２／０７／２３　２２：１０：５０　３１ＳＤＡ６００　０１４０　

−

If you are

AUTO SELECT traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area.

To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals. It stores the frequencies of six AM stations and twelve FM stations in the preset bars (1
6). − You can then use the preset bars to select those stations.

If you are in a remote area, Auto Select may not find six strong AM stations or twelve strong FM stations. If this happens, you will see a ‘‘0’’ displayed when you press the left or right side of any preset bar that does not have a station stored.

A. SEL INDICATOR

SEEK BAR

Audio System

SCAN BUTTON A. SEL BUTTON TUNE BAR

If you do not like the stations Auto Select has stored, you can store other frequencies in the preset bars. Use the TUNE, SEEK, or SCAN function to find the desired frequencies, then store them in the selected preset bars as described previously.

Auto Select does not erase the frequencies that you set previously. When you return home, turn off Auto Select by pressing the A. SEL button. The preset bars will then select the frequencies you originally set.

Comfort and Convenience Features 137

Main MenuTable of Contentsst０２／０７／２３　２２：１１：００　３１ＳＤＡ６００　０１４１　

Audio System

Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the SOUND button. The mode changes from BAS to TRE to FAD to BAL, and then back to the selected audio mode, each time you press the SOUND button. Each mode is shown in the display as it changes.

VOLUME KNOB

−

These two

Balance/Fader modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength.

Select BAL or FAD by pressing the SOUND button. Adjust the Balance or Fader to your liking by turning the VOLUME knob. The displayed number shows you the current setting. When the adjustment level reaches the center, you will see ‘‘

’’.

138

Comfort and Convenience Features

−

Treble/Bass Use these modes to adjust the tone to your liking. Select TRE or BAS by pressing the SOUND button. Adjust the desired mode by turning the VOLUME knob. The displayed number shows you the current setting. When the adjustment level reaches the center, you will see ‘‘

’’.

SOUND BUTTON

The system will automatically return the display to the selected audio mode after you stop adjusting a mode with the VOLUME knob.

Main MenuTable of Contentsst０２／０７／２３　２２：１１：１２　３１ＳＤＡ６００　０１４２　

Digital Clock The audio system usually shows the time when the ignition switch is in ACCESSORY (I) or ON (II). It shows the operation mode of the radio, CD player, or optional CD changer when you operate them, then goes back to the time display after three seconds.

To set the time, press and hold the SOUND button until the audio system beeps and the clock flashes.

To set the hours, press and hold the H (Preset 4) side of the bar until the numbers advance to the desired time.

To set the minutes, press and hold the M (Preset 5) side of the bar until the numbers advance to the desired time.

When you are finished, press the SOUND button again.

DIGITAL CLOCK

Audio System

PRESET BARS

SOUND BUTTON

You can use the R (Preset 6) side of the bar to quickly set the time to the nearest hour. Press the R (Preset 6) side of the bar while pressing the SOUND button. If the displayed time is before the half hour, pressing R sets the clock back to the previous hour. If the displayed time is after the half hour, pressing R sets the clock forward to the beginning of the next hour.

For example: 1:06 will reset to 1:00
1:52 will reset to 2:00

If your car’s battery is disconnected or goes dead, the time setting will be lost. To set the time again, follow the setting procedure.

Comfort and Convenience Features 139

Main MenuTable of Contentsst０２／０７／２３　２２：１１：２３　３１ＳＤＡ６００　０１４３　

Audio System

Radio Frequencies and Reception For information, see page

175

Operating the CD Player You operate the CD player with the same controls used for the radio.

Play only standard round discs. Odd- shaped CDs may jam in the drive or cause other problems. You can also play 3-inch (8-cm) discs without using an adapter ring. Avoid using CDs that have adhesive-type labels. The edges can curl up and cause the CD to jam in the drive.

140

Comfort and Convenience Features

AM/FM BUTTON CD/AUX BUTTON SEEK/SKIP BAR

EJECT BUTTON

RPT BUTTON RDM BUTTON

CD SLOT

PWR/VOL KNOB

Examine the CD for any labels or other contamination on it that could cause it to jam in the drive. With the ignition switch in ACCESSORY (I) or ON (II), insert the disc into the CD slot. Push the disc in halfway; the drive will pull it in the rest of the way and begin to play. The number of the track that is playing is shown in the display.

For best results when using CD-R discs, use only high quality discs labeled for audio use. When recording a CD-R, the recording must be closed in order for the disc to be used by CD players. CD-RW discs will not work in this unit.

Main MenuTable of Contentsst０２／０７／２３　２２：１１：３２　３１ＳＤＡ６００　０１４４　

When the system reaches the end of the disc, it will return to the begin- ning and play the disc again.

You can switch to the radio while a CD is playing by pressing the AM/ FM button. Press the CD button to return to playing the CD. The CD will begin playing where it left off.

If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the disc will stay in the drive. When you turn the system back on, the CD will begin playing where it left off.

Audio System

Press the eject button to remove the disc from the drive.

If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 15 seconds and put the CD player in pause mode. To begin playing the disc, press the CD button.

You can use the SEEK/SKIP bar while a disc is playing to select passages and change tracks.

To move rapidly within a track, press and hold the SEEK/SKIP bar. Press side to move forward. Press the the side to move backward. Release the bar when the system reaches the point you want.

Each time you press and release the

side of the SEEK/SKIP bar,

the system skips forward to the beginning of the next track. Press and release the side to skip backward to the beginning of the current track. Press it again to skip to the beginning of the previous track.

CONTINUED

Comfort and Convenience Features

141

Main MenuTable of Contentsst０２／０７／２３　２２：１１：４３　３１ＳＤＡ６００　０１４５　

Audio System

−

REPEAT To activate the Repeat feature, press and release the RPT button. You will see RPT in the display. The system continuously replays the current track. Press the RPT button again to turn it off.

−

RANDOM PLAY This feature, when activated, plays the tracks on the CD in random order, rather than in the order they are recorded on the CD. To activate Random Play, press and release the RDM button. You will see RDM in the display. The system will then select and play tracks randomly. This continues until you deactivate Random Play by pressing RDM again.

Protecting Compact Discs For information on how to handle and protect compact discs, see page 186

142

Comfort and Convenience Features

Operating the CD Changer (Optional) A Compact Disc changer is available for your car. It holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the in-dash CD player.

Load the desired CDs in the magazine and load the magazine in the changer according to the instructions that came with the unit. Play only standard round discs. Odd- shaped CDs may jam in the drive or cause other problems.

For best results when using CD-R discs, use only high quality discs labeled for audio use. When recording a CD-R, the recording must be closed in order for the disc to be used by CD players. CD-RW discs will not work in this unit.

To select the CD changer, press the CD button. The disc and track numbers will be displayed.

＋

−

To select a different disc, use the Preset 5 (DISC ) side or Preset 6
(DISC ) side of the preset bar. Press the Preset 6 side to select the next disc in the magazine. Press the Preset 5 side of the bar to select the previous disc. If you select an empty slot in the magazine, the changer will, after finding that slot empty, try to load the CD in the next slot. This continues until it finds a CD to load and play.

Main MenuTable of Contentsst０２／０７／２３　２２：１１：４９　３１ＳＤＡ６００　０１４６　

Audio System

If you load a CD in the in-dash player while the changer is playing a CD, the system will stop the changer and begin playing the in-dash CD. To select the changer again, press the CD button. Play will begin where it left off. Use the CD button to switch between the player and the changer.

If you eject the disc in the in-dash CD while it is playing, the system will automatically switch to the CD changer and begin play where it left off. If there are no CDs in the changer, the display will flash. You will have to select another mode (AM or FM) with the button.

When you switch back to CD mode, the system selects the same unit (in- dash or changer) that was playing when you switched out of CD mode.

To use the SKIP, REPEAT, and RANDOM functions, refer to the in- dash player operating instructions.

Comfort and Convenience Features 143

Main MenuTable of Contentsst０２／０７／２３　２２：１１：５９　３１ＳＤＡ６００　０１４７　

Audio System

CD Player Error Indications If you see an error indication in the display while operating the CD player, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.

Indication

Cause

Solution

FOCUS Error

Mechanical Error

High Temperature

Press the eject button and pull out the disc. Check if the disc is inserted correctly in the CD player. Make sure the disc is not scratched or damaged. Press the eject button and pull out the disc. Check the disc for damage or deformation. If the CD cannot be pulled out or the error indication does not disappear after the disc is ejected, see your Honda dealer. Do not try to force the disc out of the player. Will disappear when the temperature returns to normal.

144

Comfort and Convenience Features

Main MenuTable of Contentsst０２／０７／２３　２２：１２：０９　３１ＳＤＡ６００　０１４８　

CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.

Audio System

Indication

Cause

Solution

FOCUS Error

No CD in the CD Magazine

Mechanical Error

High Temperature

No CD magazine in the CD Changer

Press the magazine eject button and pull out the magazine. Check for an error indication. Insert the magazine again. If the code does not disappear or the magazine cannot be pulled out, consult your Honda dealer. Insert CD.

Press the magazine eject button and pull out the magazine. Check for an error indication. Insert the magazine again. If the code does not disappear or the magazine cannot be pulled out, consult your Honda dealer. Will disappear when the temperature returns to normal. Insert CD magazine.

Comfort and Convenience Features 145

Main MenuTable of Contentsst０２／０７／２３　２２：１２：１８　３１ＳＤＡ６００　０１４９　

Audio System

Operating the Cassette Player (Optional) The cassette system features Dolby noise reduction, automatic sensing of chromium-dioxide (CrO ) tape, and auto-reverse for continuous play.

＊

AM/FM BUTTON

TAPE DIRECTION INDICATOR

RPT INDICATOR

RPT BUTTON

CD/AUX BUTTON

To operate the cassette player, the ignition switch must be in ACCESSORY(I) or ON(II). Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.

＊

Dolby noise reduction manufactured under

license from Dolby Laboratories Licensing Corpo- ration. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories

Licensing Corporation.

SEEK/SKIP BAR

PWR/VOL KNOB

PRESET BARS

146

Comfort and Convenience Features

Main MenuTable of Contentsst０２／０７／２３　２２：１２：２６　３１ＳＤＡ６００　０１５０　

The tape direction indicator will light to show you which side of the cassette is playing. The indicates the side you inserted facing upward is now playing. If you want to play the other side, press the Preset 3
(PLAY/PROG) side of the preset bar.

▲

Audio System

If you turn the system off while a tape is playing, either with the PWR/ VOL knob or by turning off the ignition, the cassette will remain in the drive. When you turn the system back on, the cassette player will be in pause mode. To begin playing, press the Preset 3 (PLAY/PROG) side of the preset bar.

To switch to the radio or CD player while a tape is playing, press the AM/FM, or CD/AUX button. To change back to the cassette player, push the CD/AUX button.

Dolby noise reduction turns on when you insert a cassette. The indi- cator will light in the display. If the tape was not recorded with Dolby noise reduction, turn it off by pressing the Preset 4 (NR) side of the preset bar.

Noise reduction remains off until you turn it on by pressing the button again.

When the system reaches the end of the tape, it will automatically reverse direction and play the other side. If you want to remove the cassette from the drive, press the eject button on the cassette player.

Comfort and Convenience Features 147

Main MenuTable of Contentsst０２／０７／２３　２２：１２：３３　３１ＳＤＡ６００　０１５１　

Audio System

Tape Search Functions With a cassette playing, you can use the FF, REW, SKIP, or REPEAT function to find a desired program.

−

FF/REW Fast Forward and Re- wind move the tape rapidly. To re- wind the tape, push the Preset 1
(REW) side of the preset bar. You will see REW in the display. To fast forward the tape, push the Preset 2
(FF) side of the preset bar. You will see FF displayed. Press the Preset 1, 2, or 3 side of the bars to take the sys- tem out of rewind or fast forward. When the system reaches the end of the tape, it reverses direction and begins to play.

148

Comfort and Convenience Features

−

SKIP The Skip function allows you to find the beginning of a song or passage. To activate SKIP, press the SEEK/SKIP bar. Press the

side to advance to the

beginning of the next song or passage, or the side to return to the beginning of the current song or passage. FF or REW will flash in the display as the tape moves. When the system reaches the beginning of the next song or passage (FF), or the beginning of the current one (REW), it goes back to PLAY mode.

Main MenuTable of Contentsst０２／０７／２３　２２：１２：４０　３１ＳＤＡ６００　０１５２　

Audio System

The SKIP and REPEAT functions use silent periods on the tape to find the end of a song or passage. These features may not work to your satisfaction if there is almost no gap between selections, a high noise level between selections, or a silent period in the middle of a selection.

− The Repeat function

REPEAT continuously replays the current song or passage. Press the RPT button to activate it; you will see RPT displayed as a reminder. When the system reaches the end of the song or passage currently playing, it will automatically go into rewind. When it senses the beginning of the same song or passage, the system returns to PLAY mode. It will continue to repeat this same program until you deactivate REPEAT by pressing the button again.

Caring for the Cassette Player Damaged cassettes can jam inside the drive or cause other problems. See page cassette care and protection.

for information on

191

Comfort and Convenience Features

149

Main MenuTable of Contentsst０２／０７／２３　２２：１２：４８　３１ＳＤＡ６００　０１５３　

Audio System

WithoutNavigationSystem AM/FM/CD Changer Audio System ForEX,EX-V6,andLX-V6models Your Honda’s audio system provides clear reception on both AM and FM bands, while the preset bars allow you to easily select your favorite stations.

AM/FM BUTTON

STEREO INDICATOR

The in-dash CD changer holds up to six discs. You operate the CD changer with the same controls used for the radio. See page changer operation.

for CD

157

The anti-theft feature will disable the system if it is disconnected from the car’s battery. To get the system working again, you must enter a code number (see page

193

).

150

Comfort and Convenience Features

TUNE BAR

PRESET BARS

SEEK BAR

SCAN BUTTON

PWR/VOL KNOB

Main MenuTable of Contentsst０２／０７／２３　２２：１２：５９　３１ＳＤＡ６００　０１５４　

Audio System

−

Use the TUNE bar to tune

TUNE the radio to a desired frequency. Push the on the TUNE bar to tune to a higher frequency, or push the Hold the bar down until the display reaches the desired frequency.

to tune to a lower frequency.

Operating the Radio The ignition switch must be in ACCESSORY (I) or ON (II) to operate the audio system. Turn the system on by pressing the PWR/ VOL knob, or the AM or FM button. Adjust the volume by turning the knob.

The band and frequency that the radio was last tuned to is displayed. To change bands, press the AM/FM button. On the FM band, ST will be displayed if the station is broadcast- ing in stereo. Stereo reproduction on AM is not available.

You can use any of five methods to find radio stations on the selected band: TUNE, SEEK, SCAN, AUTO SELECT, and the preset bars.

or

−

The SEEK function

SEEK searches the band for a station with a strong signal. To activate it, press the SEEK bar ( ), then release it. Depending on which side of the SEEK bar you press, the system scans upward or downward from the current frequency. It stops when it finds a station with a strong signal.

CONTINUED

Comfort and Convenience Features 151

Main MenuTable of Contentsst０２／０７／２３　２２：１３：０９　３１ＳＤＡ６００　０１５５　

Audio System

−

The SCAN function

SCAN samples all the stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. You will see SCAN in the display. The system will scan up the band for a station with a strong signal. When it finds one, it will stop and play that station for approximately five seconds. If you do nothing, the system will then scan for the next strong station and play that for five seconds. When it plays a station that you want to continue listening to, press the SCAN button again.

152

Comfort and Convenience Features

−

You can store the

Preset frequencies of your favorite radio stations in the three preset bars. Each bar will store two frequencies on the AM band, and four frequencies on the FM band.

To store a frequency: 1.

Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each preset bar.

2.

3.

Use the TUNE, SEEK, or SCAN function to tune the radio to a desired station.

Pick the preset number (1
6) you want for that station. Press the left or right side of the bar and hold it until you hear a beep.

−

4.

Repeat steps 1 to 3 to store a total of six stations on AM and twelve on FM.

Once a station’s frequency is stored, simply press and release the left or right side of the proper preset bar to tune to it.

The preset frequencies will be lost if your car’s battery goes dead, is disconnected, or the radio fuse is removed.

Main MenuTable of Contentsst０２／０７／２３　２２：１３：１７　３１ＳＤＡ６００　０１５６　

−

If you are

AUTO SELECT traveling far from home and can no longer receive the stations you preset, you can use the Auto Select feature to find stations in the local area.

SEEK BAR

To activate Auto Select, press the A. SEL button. A. SEL will flash in the display, and the system will go into scan mode for several seconds. It automatically scans both bands, looking for stations with strong signals. It stores the frequencies of six AM stations and twelve FM stations in the preset bars (1
6). − You can then use the preset bars to select those stations. If you are in a remote area, Auto Select may not find six strong AM stations or twelve strong FM stations. If this happens, you will see a ‘‘0’’ displayed when you press the left or right side of any preset bar that does not have a station stored.

Audio System

AM/FM BUTTON

A. SEL INDICATOR

A. SEL BUTTON

TUNE BAR

PRESET BARS

CONTINUED

Comfort and Convenience Features 153

Main MenuTable of Contentsst０２／０７／２３　２２：１３：２４　３１ＳＤＡ６００　０１５７　

Audio System

If you do not like the stations Auto Select has stored, you can store other frequencies in the preset bars. Use the TUNE, SEEK, or SCAN function to find the desired frequencies, then store them in the selected preset bars as described previously.

Auto Select does not erase the frequencies that you set previously. When you return home, turn off Auto Select by pressing the A. SEL button. The preset bars will then select the frequencies you originally set.

SEEK BAR

154

Comfort and Convenience Features

A. SEL BUTTON

TUNE BAR

PRESET BARS

Main MenuTable of Contentsst０２／０７／２３　２２：１３：３６　３１ＳＤＡ６００　０１５８　

Adjusting the Sound Bass, Treble, Balance, and Fader are each adjustable. You select which of these you want to adjust by pressing the SOUND button. The mode changes from BAS to TRE to FAD to BAL, and then back to the selected audio mode, each time you press the SOUND button.

−

Treble/Bass Use these modes to adjust the tone to your liking. Select TRE or BAS by pressing the SOUND button. Adjust the desired mode by turning the VOLUME knob. The displayed number shows you the current setting. When the adjustment level reaches the center, you will see ‘‘

’’.

−

These two

Balance/Fader modes adjust the strength of the sound coming from each speaker. BAL adjusts the side-to-side strength, while FAD adjusts the front-to-back strength.

Audio System

SOUND BUTTON

ADJUSTMENT LEVEL

VOLUME KNOB

Select BAL or FAD by pressing the SOUND button. Adjust the Balance or Fader to your liking by turning the VOLUME knob. The displayed number shows you the current setting. When the adjustment level reaches the center, you will see ‘‘

’’.

The system will automatically return the display to the selected audio mode about five seconds after you stop adjusting a mode with the SOUND button.

Radio Frequencies and Reception For information, see page

175

Comfort and Convenience Features 155

Main MenuTable of Contentsst０２／０７／２３　２２：１３：４９　３１ＳＤＡ６００　０１５９　

Audio System

Digital Clock The audio system usually shows the time when the ignition switch is in ACCESSORY (I) or ON (II). It shows the operation mode of the radio, or CD changer when you operate them, then goes back to the time display after three seconds.

To set the time, press and hold the SOUND button until the audio system beeps and the clock flashes.

To set the hours, press and hold the H (Preset 4) side of the bar until the numbers advance to the desired time.

To set the minutes, press and hold the M (Preset 5) side of the bar until the numbers advance to the desired time.

When you are finished, press the SOUND button again.

156

Comfort and Convenience Features

DIGITAL CLOCK

PRESET BARS

You can use the R (Preset 6) side of the bar to quickly set the time to the nearest hour. Press R while pressing the SOUND button. If the displayed time is before the half hour, pressing R sets the clock back to the previous hour. If the displayed time is after the half hour, pressing R sets the clock forward to the beginning of the next hour.

SOUND BUTTON

For example:

1:06 would RESET to 1:00. 1:52 would RESET to 2:00.

If your car’s battery is disconnected or goes dead, the time setting will be lost. To set the time again, follow the setting procedure.

Main MenuTable of Contentsst０２／０７／２３　２２：１３：５９　３１ＳＤＡ６００　０１６０　

Operating the CD Changer Your Honda’s audio system has an in-dash CD changer that holds up to six discs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the radio.

To load CDs or operate the CD changer, the ignition switch must be in ACCESSORY (I) or ON (II).

Load and play only standard round discs. Odd-shaped CDs may jam in the drive or cause other problems. You cannot load and play 3-inch (8-cm) discs in this system.

For best results when using CD-R discs, use only high quality discs labeled for audio use. When recording a CD-R, the recording must be closed in order for the disc to be used by CD players. CD-RW discs will not work in this unit.

Audio System

CD LOAD INDICATOR

CD BUTTON

DISC NUMBER

RPT BUTTON

EJECT BUTTON CD SLOT

LOAD BUTTON

CONTINUED

Comfort and Convenience Features 157

Main MenuTable of Contentsst０２／０７／２３　２２：１４：１２　３１ＳＤＡ６００　０１６１　

Audio System

LoadingCDsintheChanger To load multiple CDs in one operation:

1.

2.

3.

Press and hold the LOAD button until you hear a beep and see ‘‘LOAd’’ in the display, then release the button.

On the upper left side of the display, the disc number for an empty position will begin blinking and the green CD load indicator will come on.

Insert the disc into the CD slot. Insert it only about halfway; the drive will pull it in the rest of the way. You will see ‘‘BUSY’’ in the display. The CD load indicator turns red and blinks as the CD is loaded.

158

Comfort and Convenience Features

4.

When the CD load indicator turns green, press the LOAD button again. When ‘‘LOAd’’ appears in the display, insert the next disc into the CD slot.

5.

Repeat this until all six positions are loaded. The system will then begin playing the last CD loaded.

If you are not loading CDs into all six positions, the system will begin playing the last CD loaded.

If you stop loading CDs before all six positions are filled, and you do not press the LOAD button, the system will wait for ten seconds, then stop the load operation and begin playing the last CD loaded.

To load a single CD:

1.

Press and release the LOAD button.

2.

The disc number for an empty position starts to blink and the green CD load indicator comes on. When you see ‘‘LOAd’’ in the display, insert the disc into the CD slot. Insert it only about halfway; the drive will pull it in the rest of the way.

3.

The system will load the CD, and begin playing it.

Main MenuTable of Contentsst０２／０７／２３　２２：１４：２０　３１ＳＤＡ６００　０１６２　

If you press the LOAD button while a CD is playing, the system will stop playing that CD and start the loading sequence. It will then play the CD just loaded.

You can also load a CD into an empty position while a CD is playing by pressing the appropriate side of a preset bar. Select an empty position (the disc number indicator is off), and press the left or right side of the preset bar for that position (1 to 6). The system will stop playing the current CD and start the loading sequence. It will then play the CD just loaded.

Audio System

CD BUTTON

SCAN INDICATOR

RDM INDICATOR

SKIP BAR

RPT INDICATOR

RPT BUTTON

LOAD BUTTON

SCAN BUTTON

RDM BUTTON

PRESET BARS

CONTINUED

Comfort and Convenience Features 159

Main MenuTable of Contentsst０２／０７／２３　２２：１４：３０　３１ＳＤＡ６００　０１６３　

Audio System

Operation Select the CD changer by pressing the CD button. You will see ‘‘CD’’ in the display. The system will begin playing the last selected disc in the CD changer. You will see the disc and track numbers displayed.

When that disc ends, the next disc in the CD changer is loaded and played. After the last disc finishes, the system returns to disc 1.

To select a different disc, press the appropriate side of a preset bar (1
− 6). If you select an empty position in the CD changer, the system will go into the loading sequence (see page 158

).

You can use the SKIP bar while a disc is playing to select passages and change tracks.

160

Comfort and Convenience Features

To move rapidly within a track, press and hold the left or right side of the SKIP bar. You will hear a beep and the system will continue to move. Press

to move forward, or

to move backward. Release the

bar when the system reaches the point you want.

and

Each time you press release it, the system skips forward to the beginning of the next track. Press and release backward to the beginning of the current track. Press and release it again to skip to the beginning of the previous track.

to skip

−

REPEAT To activate the Repeat feature, press and release the RPT button. You will see RPT in the display as a reminder. The system continuously replays the current track. Press the RPT button again to turn it off. Pressing either side of the SKIP bar also turns off the repeat feature.

−

This feature,

RANDOM PLAY when activated, plays the tracks within a CD in random order, rather than in the order they are recorded on the CD. To activate Random Play, press the RDM button. You will see RDM in the display. The system will then select and play tracks randomly. This continues until you deactivate Random Play by pressing the RDM button again, or you select a different CD with a preset bar.

Main MenuTable of Contentsst０２／０７／２３　２２：１４：３７　３１ＳＤＡ６００　０１６４　

AM/FM BUTTON

To take the system out of CD mode, press the AM/FM button. Each time you press the AM/FM button, the system will change to the next mode; FM1, FM2 or AM. When you return to CD mode by pressing the CD button, play will continue at the same point that it left off.

If you turn the system off while a CD is playing, either with the PWR button or the ignition switch, play will continue at the same point when you turn it back on.

Audio System

CD BUTTON

PWR BUTTON

CONTINUED

Comfort and Convenience Features 161

Main MenuTable of Contentsst０２／０７／２３　２２：１４：４５　３１ＳＤＡ６００　０１６５　

CD BUTTON

CD SLOT

EJECT BUTTON

Audio System

RemovingCDsfromtheChanger To remove the disc that is currently playing, press the eject button. You will see ‘‘EJEC’’ in the display. When you remove the disc from the slot, the system automatically begins the Load sequence so you can load another CD in that position. If you do not load another CD, after 15
seconds, the system selects the previous mode (AM, FM1, or FM2).

If you do not remove the disc from the slot, the system will reload the disc after 15 seconds, and select the previous mode (AM or FM). To begin playing the disc, press the CD button.

To remove a different CD from the changer, first select it with the left or right side of the appropriate preset bar. When that CD begins playing, press the eject button.

162

Comfort and Convenience Features

Main MenuTable of Contentsst０２／０７／２３　２２：１４：５２　３１ＳＤＡ６００　０１６６　

Audio System

Protecting Compact Discs For information on how to handle and protect compact discs, see page 186

If you press the eject button while listening to the radio, or with the audio system turned off, the disc that was last selected is ejected. After that disc is ejected, pressing the eject button again will eject the next disc in numerical order. By doing this six times, you can remove all the CDs from the changer.

In any mode, if you press the eject button and hold it until you hear a beep, the system will eject all of the discs in the changer.

You can also eject discs when the ignition switch is off by pressing the eject button. The disc that was last selected is ejected first. You can eject up to five discs, one at a time.

Comfort and Convenience Features 163

Main MenuTable of Contentsst０２／０７／２３　２２：１５：０１　３１ＳＤＡ６００　０１６７　

Audio System

CD Changer Error Indications If you see an error indication in the display while operating the CD changer, find the cause in the chart to the right. If you cannot clear the error indication, take the car to your Honda dealer.

Indication

Cause

Solution

FOCUS Error

Mechanical Error

No CD in the CD Changer

Press the CD eject button and pull out the CDs. Check for an error indication. Insert the CDs again. If the code does not disappear or the CDs cannot be pulled out, consult your Honda dealer. Press the CD eject button and pull out the CDs. Check for an error indication. Insert the CDs again. If the code does not disappear or the CDs cannot be pulled out, consult your Honda dealer. Insert CDs.

164

Comfort and Convenience Features

Main MenuTable of Contentsst０２／０７／２３　２２：１５：１１　３１ＳＤＡ６００　０１６８　

Operating the Cassette Player (Optional) The cassette system features Dolby noise reduction, automatic sensing of chromium-dioxide (CrO ) tape, and auto-reverse for continuous play.

＊

Audio System

AM/FM BUTTON

TAPE DIRECTION INDICATOR

RPT INDICATOR

CD/AUX BUTTON

To operate the cassette player, the ignition switch must be in ACCESSORY(I) or ON(II). Make sure the tape opening on the cassette is facing to the right, then insert the cassette most of the way into the slot. The system will pull it in the rest of the way, and begin to play.

＊

Dolby noise reduction manufactured under

license from Dolby Laboratories Licensing Corpo- ration. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories

Licensing Corporation.

RPT BUTTON

SEEK/SKIP BAR

PWR/VOL KNOB

PRESET BARS

CONTINUED

Comfort and Convenience Features 165

Main MenuTable of Contentsst０２／０７／２３　２２：１５：１８　３１ＳＤＡ６００　０１６９　

Dolby noise reduction turns on when you insert a cassette. The indi- cator will light in the display. If the tape was not recorded with Dolby noise reduction, turn it off by pressing the Preset 4 (NR) side of the preset bar.

Noise reduction remains off until you turn it on by pressing the button again.

When the system reaches the end of the tape, it will automatically reverse direction and play the other side. If you want to remove the cassette from the drive, press the eject button on the cassette player.

If you turn the system off while a tape is playing, either with the PWR/