You may also be interested in...
Download PDF Manual

Driving with the Paddle Shifters (Automatic Transmission Only)


When you accelerate from a stop, the transmission starts in first gear, and you must manually upshift between first and fifth gears. Make sure you upshift before the engine speed reaches the tachometer’s red zone.


Downshifting with the paddle shifter allows you to increase the engine braking when going down steep or long hills, and provides more power when climbing uphills. You can upshift the transmission manually to reduce the rpm.


The transmission remains in the selected gear (5, 4, 3, 2, or 1). There is no automatic downshift when your push the accelerator pedal to the floor.


The transmission also shifts automatically as the vehicle comes to a complete stop. It downshifts to first gear when the vehicle speed reaches 6 mph (10 km/h) or less.


When you are driving in 4th or 5th gear, the transmission downshifts to the lower gear under the following conditions:


The vehicle slows down to a certain speed.


You press the brake pedal.


318


The automatic transmission will not allow you to shift up or down if:


You downshift before the engine speed reaches the highest threshold of the lower gear.


If you try to do this, the gear position indicator will flash the number of the lower gear several times, then return to a higher gear.


If the vehicle speed decreases below the redline of the selected lower gear while the indicator is flashing, the transmission downshifts, and the indicator displays the selected gear.


You upshift before the engine speed reaches the lowest threshold of the higher gear.


You pull both paddle shifters at the same time.


2012 Accord Coupe


Driving with the Paddle Shifters (Automatic Transmission Only)



(right) paddle shifter to


StartinginSecondGear When you are in sequential shift mode, and the vehicle is stopped, pull the shift to second gear. You will see ‘‘M2’’ in the display. Starting in second gear helps to reduce wheelspin in deep snow or on a slippery surface.


RecommendedShiftPoints Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you good fuel economy and effective emissions control. The following shift points are recommended:


Shift up


Normal acceleration


1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th


15 mph (24 km/h) 25 mph (40 km/h) 40 mph (64 km/h) 45 mph (72 km/h)


319


2012 Accord Coupe


Parking


Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly, or your vehicle may roll if it is parked on an incline.


If your vehicle has an automatic transmission, set the parking brake before you put the transmission in Park. This keeps the vehicle from moving and putting pressure on the parking mechanism in the transmission.


320


If the vehicle is facing uphill, turn the front wheels away from the curb. If your vehicle has a manual transmission, put it in first gear.


If the vehicle is facing downhill, turn the front wheels toward the curb. If your vehicle has a manual transmission, put it in reverse gear.


Make sure the parking brake is fully released before driving away. Driving with the parking brake partially set can overheat or damage the rear brakes.


Parking Tips


Make sure the moonroof (if equipped) and the windows are closed.


Turn off the lights.


Place any packages, valuables, etc., in the trunk or take them with you.


Lock the doors.


Check the indicator on the instrument panel to verify that the security system is set.


Never park over dry leaves, tall grass, or other flammable materials. The hot three way catalytic converter could cause these materials to catch on fire.


2012 Accord Coupe


Your vehicle is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The emergency brake assist system increases the stopping force when you depress the brake pedal hard in an emergency situation. The anti-lock brake system (ABS) helps you retain steering control when braking very hard.


Resting your foot on the pedal keeps the brakes applied lightly, builds up heat, reduces their effectiveness and reduces brake pad life. In addition, fuel economy can be reduced. It also keeps your brake lights on all the time, confusing drivers behind you.


Constant application of the brakes when going down a long hill builds up heat and reduces their effective- ness. Use the engine to assist the brakes by taking your foot off the accelerator and downshifting to a lower gear.


Check the brakes after driving through deep water. Apply the brakes moderately to see if they feel normal. If not, apply them gently and frequently until they do. Be extra cautious in your driving.


Braking System


Braking System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels.


Brake Pad Wear Indicators The front and rear disc brakes on all models have audible brake pad wear indicators.


If the brake pads need replacing, you will hear a distinctive, metallic screeching sound when you apply the brake pedal. If you do not have the brake pads replaced, they will screech all the time. It is normal for the brakes to occasionally squeal or squeak when you apply them.


321


2012 Accord Coupe You will feel a pulsation in the brake pedal when the ABS activates, and you may hear some noise. This is normal: it is the ABS rapidly pumping the brakes. On dry pavement, you will need to press on the brake pedal very hard before the ABS activates. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice.


Anti-lock Brakes (ABS)


The anti-lock brake system (ABS) helps prevent the wheels from locking up, and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it.


The electronic brake distribution (EBD) system, which is part of the ABS, also balances the front-to-rear braking distribution according to vehicle loading.


Youshouldneverpumpthebrakepedal. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal. This is sometimes referred to as ‘‘stomp and steer.’’


322


ABS Indicator


If this indicator comes on, the anti- lock function of the braking system has shut down. The brakes still work like a conventional system, but without anti-lock. You should have your dealer inspect your vehicle as soon as possible.


If the ABS indicator comes on while driving, test the brakes as shown on page


407


2012 Accord Coupe


If the ABS indicator and the brake system indicator come on together, and the parking brake is fully released, the EBD system may also be shut down.


ImportantSafetyReminders ABS does not reduce the time or distance it takes to stop the vehicle. It only helps with the steering control during braking.


A vehicle with ABS may require a longer distance to stop loose or uneven surfaces, such as gravel snow, than a vehicle without anti-lock.


on


Anti-lock Brakes (ABS)


407


. If the brakes feel normal,


Test your brakes as instructed on page drive slowly and have your vehicle repaired by your dealer as soon as possible. Avoid sudden hard braking which could cause the rear wheels to lock up and possibly lead to a loss of control.


ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. Always drive at a safe speed for the road and weather conditions.


ABS cannot prevent a loss of stability. Always steer moderately when you are braking hard. Severe or sharp steering wheel movement can still cause your vehicle to veer into oncoming traffic or off the road.


323


2012 Accord Coupe


Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System


VSA OFF Indicator


When VSA is off, the VSA OFF indicator comes on as a reminder.


Vehicle Stability Assist (VSA) System Indicator


When VSA activates, you will see the VSA system indicator blink.


If this indicator comes on while driving, pull to the side of the road when it is safe, and turn off the engine. Reset the system by restarting the engine. If the VSA system indicator stays on or comes back on while driving, have the VSA system inspected by your dealer.


The vehicle stability assist (VSA) system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine’s output and by selectively applying the brakes.


When VSA activates, you may notice that the engine does not respond to the accelerator in the same way it does at other times. There may also be some noise from the VSA hydraulic system. You will also see the VSA system indicator blink.


The VSA system cannot enhance the vehicle’s driving stability in all situations and does not control your vehicle’s entire braking system. It is still your responsibility to drive and corner at reasonable speeds and to leave a sufficient margin of safety.


324


The main function of the


NOTE: VSA system is generally known as Electronic Stability Control (ESC). The system also includes a traction control function.


If the low tire pressure indicator or TPMS indicator comes on, the VSA system automatically turns on even if the VSA system is turned off by pressing the VSA OFF switch (see page cannot turn the VSA system off by pressing the VSA OFF switch again.


). If this happens, you


325


Without VSA, your vehicle will have normal braking and cornering ability, but it will not have VSA traction and stability enhancement.


2012 Accord Coupe


Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System


VSA OFF Switch


VSA OFF SWITCH


This switch is under the driver’s side vent. To turn the VSA system on and off, press and hold it until you hear a beep.


When VSA is off, the VSA OFF indicator comes on as a reminder. Press and hold the switch again. It turns the system back on.


VSA is turned on every time you start the engine, even if you turned it off the last time you drove the vehicle.


In certain unusual conditions when your vehicle gets stuck in shallow mud or fresh snow, it may be easier to free it with the VSA temporarily switched off. When the VSA system is off, the traction control system is also off. You should only attempt to free your vehicle with the VSA off if you are not able to free it when the VSA is on.


Immediately after freeing your vehicle, be sure to switch the VSA on again. We do not recommend driving your vehicle with the VSA and traction control systems switched off.


VSA and Tire Sizes Driving with varying tire or wheel sizes may cause the VSA to malfunction. When replacing tires, make sure they are of the same size and type as your original tires (see page


385


).


If you install winter tires, make sure they are the same size as those that were originally supplied with your vehicle. Exercise the same caution during winter driving as you would if your vehicle was not equipped with VSA.


325


2012 Accord Coupe


Tire Pressure Monitoring System (TPMS)


Your vehicle is equipped with a tire pressure monitoring system (TPMS) that turns on every time you start the engine and monitors the pressure in your tires while driving.


Each tire has its own pressure sensor (not including the spare tire). If the air pressure of a tire becomes significantly low while driving, the sensor in that tire immediately sends a signal that causes the low tire pressure indicator to come on.


Low Tire Pressure Indicator


When the low tire pressure indicator is on, one or more of your tires is significantly underinflated. You should stop and check your tires as soon as possible, and inflate them to the proper pressure as indicated on the vehicle’s tire information placard.


If you think you can safely drive a short distance to a service station, proceed slowly, and inflate the tire to the recommended pressure shown on the driver’s doorjamb.


If the tire is flat, or if the tire pressure is too low to continue driving, replace the tire with the compact spare tire (see page 393


).


If you cannot make the low tire pressure indicator go out after inflating the tires to the specified values, have your dealer check the system as soon as possible.


326


Driving on a significantly under inflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.


Because tire pressure varies by temperature and other conditions, the low tire pressure indicator may come on unexpectedly.


2012 Accord Coupe


For example, if you check and fill your tires in a warm area, then drive in extremely cold weather, the tire pressure will be lower than measured and could be underinflated and cause the low tire pressure indicator to come on. Or, if you check and adjust your tire pressure in cooler conditions, and drive into extremely hot conditions, the tire may become overinflated. However, the low tire pressure indicator will not come on if the tires are overinflated.


Refer to page guidelines.


379


for tire inflation


Although your tire pressure is monitored, you must manually check the tire pressures monthly.


Each tire, including the spare, should be checked monthly when cold, and set to the recommended inflation pressure as specified on the tire


Tire Pressure Monitoring System (TPMS)


information label and in the owner’s manual (see page


380


).


Tire Pressure Monitoring System (TPMS) Indicator This indicator comes on and stays on if there is a problem with the tire pressure monitoring system.


If this happens, the system will shut off and no longer monitor tire pressures. Have the system checked by your dealer as soon as possible.


If the low tire pressure indicator or TPMS indicator comes on, the VSA system automatically turns on even if the VSA system is turned off by pressing the VSA OFF switch (see page cannot turn the VSA system off by pressing the VSA OFF switch again.


). If this happens, you


325


When you restart the vehicle with the compact spare tire, the TPMS indicator may also come on and stay on after driving several miles (kilometers).


327


2012 Accord Coupe


Tire Pressure Monitoring System (TPMS)


The low tire pressure indicator or the TPMS indicator will go off, after several miles (kilometers) driving, when you replace the spare tire with the specified regular tire equipped with the tire pressure monitor sensor.


Never use a puncture-repairing agent in a flat tire. If used, you will have to replace the tire pressure sensor. Have the flat tire repaired by your dealer as soon as possible.


AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.


Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.


ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.


Changing a Tire with TPMS If you have a flat tire, the low tire pressure indicator will come on. Replace the flat tire with the compact spare tire (see page


393


).


Each wheel (except the compact spare tire wheel) is equipped with a tire pressure sensor. You must use TPMS specific wheels. It is recommended that you always have your tires serviced by your dealer or qualified technician.


After you replace the flat tire with the compact spare tire, the low tire pressure indicator stays on. This is normal; the system is not monitoring the spare tire pressure. Manually check the spare tire pressure to be sure it is correct. After several miles (kilometers) driving with the compact spare tire, the TPMS indicator comes on and the low tire pressure indicator goes off.


328


2012 Accord Coupe


Load Limits


Your vehicle has been designed primarily to carry passengers and their cargo. You can also use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section.


Towing a Trailer


Break-InPeriod Avoid towing a trailer during your vehicle’s first 600 miles (1,000 km) (see page


284


).


Exceeding any load limit or improperly loading your vehicle and trailer can cause a crash in which you can be seriously hurt or killed.


Check the loading of your vehicle and trailer carefully before starting to drive.


The


Total Trailer Weight: maximum allowable weight of the trailer and everything in or on it must not exceed 1,000 lbs (450 kg). Towing a load that is too heavy can seriously affect your vehicle’s handling and performance. It can also damage the engine and drivetrain.


The weight that


Tongue Load: the tongue of a fully-loaded trailer puts on the hitch should be approximately 10% of the total trailer weight. Too much tongue load reduces front-tire traction and steering control. Too little tongue load can make the trailer unstable and cause it to sway.


CONTINUED


329


2012 Accord Coupe


Towing a Trailer


To achieve a proper tongue load, start by loading 60% of the load toward the front of the trailer and 40% toward the rear, then re-adjust the load as needed.


Gross Vehicle Weight Rating (GVWR): The maximum allowable weight of the vehicle, all occupants, all accessories, all cargo, and the tongue load is:


Canadian models


LX:


1,970 kg


EXandEX-L:


2,020 kg


V6modelswithautomatic transmission:


2,075 kg


V6modelswithmanualtransmission:


2,040 kg


U.S. models


LX:


4,299 lbs (1,950 kg)


EXandEX-L:


4,409 lbs (2,000 kg)


V6modelswithautomatic transmission:


4,541 lbs (2,060 kg)


V6modelswithmanualtransmission:


4,475 lbs (2,030 kg)


330


2012 Accord Coupe


Gross Axle Weight Rating (GAWR): The maximum allowable weight at the vehicle axles is:


U.S. models


V6modelswithmanualtransmission:


2,425 lbs (1,100 kg) on the front axle 2,050 lbs (930 kg) on the rear axle


LX:


2,337 lbs (1,060 kg) on the front axle 2,006 lbs (910 kg) on the rear axle


EXandEX-L:


2,414 lbs (1,095 kg) on the front axle 2,039 lbs (925 kg) on the rear axle


V6modelswithautomatic transmission:


2,535 lbs (1,150 kg) on the front axle 2,050 lbs (930 kg) on the rear axle


Towing a Trailer


Canadian models


LX:


1,065 kg on the front axle 910 kg on the rear axle


EXandEX-L:


1,095 kg on the front axle 930 kg on the rear axle


V6modelswithautomatic transmission:


1,160 kg on the front axle 950 kg on the rear axle


V6modelswithmanualtransmission:


1,110 kg on the front axle 950 kg on the rear axle


331


2012 Accord Coupe


Towing a Trailer


Checking Loads The best way to confirm that all loads are within limits is to check them at a public scale. For public scales in your area, check your local phone book, or contact your trailer dealer or rental agency for assistance.


If you cannot get to a public scale, you can estimate the total trailer weight by adding the weight of your trailer (as quoted by the manufacturer) with everything in or on the trailer.


Towing Equipment and Accessories Towing can require a variety of equipment, depending on the size of your trailer, how it will be used, how much load you are towing, and where you tow.


Discuss your needs with your trailer sales or rental agency, and follow the guidelines in this section. Also make sure that all equipment is properly installed and maintained, and that it meets federal, state, province, territory, and local regulations.


Hitches Any hitch used on your vehicle must be properly bolted to the underbody.


SafetyChains Always use safety chains when you tow a trailer. Make sure the chains are secured to the trailer and hitch, and that they cross under the tongue and can catch the trailer if it becomes unhitched. Leave enough slack to allow the trailer to turn corners easily, but do not let the chains drag on the ground.


If you normally pull the same load each time you tow a trailer, you can use a suitable scale or a special tongue load gauge to check the tongue load the first time you set up a towing combination (a fully loaded vehicle and trailer), then recheck the tongue load whenever the conditions change.


332


2012 Accord Coupe


TrailerBrakes There are two common types of trailer brakes: surge and electric. Surge brakes are common for boat trailers, since the brakes will get wet.


If you choose electric brakes, be sure they are electronically actuated. Do not attempt to tap into your vehicle’s hydraulic system. No matter how successful it may seem, any attempt to attach trailer brakes to your vehicle’s hydraulic system will lower braking effectiveness and create a potential hazard.


See your trailer dealer or rental agency for more information on installing electric brakes.


TrailerLights Trailer lights and equipment must comply with federal, state, province, territory, and local regulations. Check with your local trailer sales or rental agencies for the requirements in the area where you plan to tow, and use only equipment designed for your vehicle.


Since lighting and wiring vary by trailer type and brand, you should have a qualified technician install a suitable connector between the vehicle and the trailer. Improper equipment or installation can cause damage to your vehicle’s electrical system and affect your vehicle warranty.


Towing a Trailer


AdditionalTowingEquipment Many states and Canadian provinces/territories require special outside mirrors when towing a trailer. Even if they don’t, you should install special mirrors if you cannot clearly see behind you, or if the trailer creates a blind spot.


Ask your trailer sales or rental agency if any other items are recommended or required for your towing situation.


333


2012 Accord Coupe The lights and brakes on your vehicle and the trailer are working properly.


Your vehicle tires and spare are properly inflated, and the trailer tires and spare are inflated as recommended by the trailer maker.


Driving Safely With a Trailer The added weight, length, and height of a trailer will affect your vehicle’s handling and performance, so driving with a trailer requires some special driving skills and techniques.


For your safety and the safety of others, take time to practice driving maneuvers before heading for the open road, and follow the guidelines in this section.


Towing a Trailer


Pre-Tow Checklist When preparing to tow, and before driving away, be sure to check the following:


The vehicle has been properly serviced, and the suspension and the cooling system are in good operating condition.


The trailer has been properly serviced and is in good condition.


All weights and loads are within limits.


The hitch, safety chains, and any other attachments are secure.


All items in or on the trailer are properly secured and cannot shift while you drive.


334


2012 Accord Coupe


TowingSpeedsandGears Drive slower than normal in all driving situations, and obey posted speed limits for vehicles with trailers.


Do not exceed the limited speed when towing a trailer. At higher speeds, the trailer may sway or affect vehicle handling (see ‘‘ ’’ in the next page for onHills additional gear information).


Driving


If your vehicle has an automatic transmission, use the D position when towing a trailer on level roads.


4-cylindermodelswith automatic transmission D3 is the proper shift lever position to use when towing a trailer in hilly terrain.


V6modelswithautomatictransmission When driving uphill and downhill, use the S position (without using the paddle shifters) to provide the proper engine power and engine braking on each gear. You can also use the paddle shifters. In this case, select third, second, or first gear with the paddle shifter; depending on the vehicle speeds and road condition. Do not use fourth and fifth gears.


Towing a Trailer


If the automatic transmission fluid temperature increases and exceeds the specified limit, the transmission will also automatically downshift to the first gear even with the Sequential Sportshift Mode. This prevents the automatic transmission from overheating. In this case, the gear position ‘‘1’’ next to the ‘‘M’’ indicator in the instrument panel blinks for about five seconds, then it stays on.


MakingTurnsandBraking Make turns more slowly and wider than normal. The trailer tracks a smaller arc than your vehicle, and it can hit or run over something the vehicle misses. Allow more time and distance for braking. Do not brake or turn suddenly as this could cause the trailer to jackknife or turn over.


CONTINUED


335


2012 Accord Coupe


Towing a Trailer


DrivingonHills When climbing hills, closely watch your temperature gauge. If it nears the red (Hot) mark, turn the air conditioning off, reduce speed and, if necessary, pull to the side of the road to let the engine cool.


When driving down hills, reduce your speed and always apply engine braking by shifting down. If your vehicle has a manual transmission, when going down a steep hill, use the second gear to provide greater engine braking.


4-cylindermodelswith automatic transmission If the automatic transmission shifts frequently while going up a hill, shift to D3.


When driving down hills, reduce your speed and shift down to the second gear.


336


V6modelswithautomatictransmission When driving down hills, reduce your speed and use the S mode. You can also use the paddle shifters to change the gear position. Select third, second or first gear depending on the vehicle speeds and road condition. When going down a steep hill, use second gear to provide greater engine braking. Shift down to first gear when driving up steep hills.


Do not ‘‘ride’’ the brakes, and remember, it will take longer to slow down and stop when towing a trailer.


If you must stop when facing uphill, use the foot brake or parking brake. Do not try to hold the vehicle in place by pressing on the accelerator, as this can cause the automatic transmission to overheat.


HandlingCrosswindsandBuffeting Crosswinds and air turbulence caused by passing trucks can disrupt your steering and cause the trailer to sway. When being passed by a large vehicle, keep a constant speed, and steer straight ahead. Do not try to make quick steering or braking corrections.


2012 Accord Coupe


BackingUp Always drive slowly and have someone guide you when backing up. Grip the of the steering wheel, then turn the wheel to the left to get the trailer to move to the left, and turn the wheel right to move the trailer to the right.


bottom


Parking Follow all normal precautions when parking, including firmly setting the parking brake and putting the transmission in Park (automatic) or in first or reverse (manual). Also, place wheel chocks at each of the trailer’s tires.


Towing Your Vehicle Your vehicle is not designed to be towed behind a motor home. If your vehicle needs to be towed in an emergency, see page


415


Towing a Trailer


337


2012 Accord Coupe


338


2012 Accord Coupe


This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions.


This section also includes instructions on how to read the Maintenance Minder messages on the information display, and instructions for simple maintenance tasks you may want to take care of yourself.


If you have the skills and tools to perform more complex maintenance tasks on your vehicle, you may want to purchase the service manual. See page for information on how to obtain a copy, or see your dealer.


439


U.S. Vehicles: Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.


Maintenance


TM


Maintenance Safety Maintenance Minder Fluid Locations Adding Engine Oil Changing the Engine Oil and


...................... ................. .............................. ........................


Filter


Engine Coolant Windshield Washers Transmission Fluid


........................................... .............................. .................... ....................... .......... .............. ................ .................... .................................... ............................................. ................ ..................................... .................. ................................. ............................................... ................... ............................. ..................................


Automatic Transmission Manual Transmission Brake and Clutch Fluid Power Steering Fluid Timing Belt Lights Cleaning the Seat Belts Floor Mats Dust and Pollen Filter Wiper Blades Tires Checking the Battery Vehicle Storage Interior Care


. 340
. 341
. 348
. 350


. 352
. 354
. 356
. 357
. 357
. 359
. 362
. 363
. 364
. 365
. 374
. 375
. 375
. 376
. 379
. 387
. 388
. 389


339


2012 Accord Coupe


Maintenance Safety


All service items not detailed in this section should be performed by a certified technician or qualified mechanic.


Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required.


Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off.


To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.


To reduce the possibility of fire or explosion, keep cigarettes, sparks, and flames away from the battery and all fuel-related parts.


Wear eye protection and protective clothing when working with the battery or compressed air.


340


Improperly maintaining this vehicle, or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.


Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.


Injury from moving parts. not run the engine unless instructed to do so.


Do


Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.


Always follow the procedures and precautions in this owner’s manual.


Potential Vehicle Hazards


Carbon Monoxide poison from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine.


Burns from hot parts. Let the engine and exhaust system cool down before touching any parts.


Some of the most important safety precautions are given here. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.


2012 Accord Coupe


Your vehicle displays engine oil life and maintenance service items on the information display to show you when you should have your dealer do engine oil replacement and indicated maintenance service.


Based on the engine operating conditions, the onboard computer in your vehicle calculates the remaining engine oil life and displays it as a percentage.


Maintenance Minder


TM


Engine Oil Life Display


SELECT/RESET KNOB


The remaining engine oil life is shown on the display according to this table:


Calculated Engine


Displayed


ENGINE OIL LIFE INDICATOR


U.S. V6 model is shown.


To see the current engine oil life, turn the ignition switch to the ON (II) position, then press and release the select/reset knob repeatedly until the engine oil life indicator appears (see page


64


).


Oil Life (%) 91% 100% 81% 90% 71% 80% 61% 70% 60% 51% 41% 50% 31% 40% 21% 30% 16% 20% 15% 11% 6% 10% 5% 1%


− − − − − − − − − − − − 0%


Engine Oil Life (%)


100% 90% 80% 70% 60% 50% 40% 30% 20% 15% 10% 5% 0%


CONTINUED


341


2012 Accord Coupe


Maintenance Minder


TM


MAINTENANCE MINDER INDICATOR


ENGINE OIL LIFE INDICATOR


MAINTENANCE ITEM CODE(S)


U.S. V6 model is shown.


If the remaining engine oil life is 15
to 6 percent, you will see the engine oil life indicator every time you turn the ignition switch to the ON (II) position. The Maintenance Minder indicator will also come on, and the maintenance item code(s) for other scheduled maintenance items needing service will be displayed next to the engine oil life indicator.


342


The 15 and 10 percent oil life indicators remind you that your vehicle will soon be due for scheduled maintenance.


When the remaining engine oil life is 5 to 1 percent, you will see a ‘‘SERVICE’’ message along with the same maintenance item code(s), every time you turn the ignition switch to the ON (II) position.


2012 Accord Coupe


Maintenance Minder


TM


The maintenance item code or codes indicate the main and sub items required at the time of the oil change (see page


347


).


You can switch the information display from the engine oil life display to the odometer or the trip meter. Press and release the select/ reset knob on the instrument panel.


When the engine oil life is 15 to 1
percent, the Maintenance Minder indicator ( ) comes on every time you turn the ignition switch to the ON (II) position, then it goes out if you switch the information display.


When you see this message, have the indicated maintenance performed by your dealer as soon as possible.


NEGATIVE DISTANCE TRAVELED


When the remaining engine oil life is 0 percent, the engine oil life indicator will blink. The display comes on every time you turn the ignition switch to the ON (II) position. The Maintenance Minder indicator on in the instrument panel. When you see this message, immediately have the indicated maintenance done by your dealer.


) also comes on and remains


If you do not perform the indicated maintenance, negative distance traveled is displayed and begins to blink after the vehicle has been driven 10 miles (10 km) or more.


Negative distance traveled means your vehicle has passed the maintenance required point. Immediately have the indicated maintenance done by your dealer.


CONTINUED


343


2012 Accord Coupe


Maintenance Minder


TM


To change the information display from the engine oil life display to the odometer or the trip meter, press and release the select/reset knob.


When the engine oil life is 0 percent or negative distance traveled, the Maintenance Minder indicator ) remains on even if you change the information display.


Immediately have the service performed, and make sure to reset the display as described as follows.


344


Maintenance Main Items and Sub Items


MAINTENANCE MINDER INDICATOR


MAINTENANCE MAIN ITEM


ENGINE OIL LIFE


MAINTENANCE SUB ITEM(S)


U.S. V6 model is shown.


All maintenance items displayed on the information display are in code. For an explanation of these maintenance codes, see page


347


Resetting the Engine Oil Life Display Your dealer will reset the display after completing the required maintenance service. You will see ‘‘OIL LIFE 100%’’ on the information display the next time you turn the ignition switch to the ON (II) position.


If maintenance service is done by someone other than your dealer, reset the Maintenance Minder as follows:


1.


Turn the ignition switch to the ON (II) position.


2.


Press the select/reset knob repeatedly until the engine oil life indicator is displayed.


2012 Accord Coupe


3.


Press the select/reset knob for about 10 seconds. The engine oil life and the maintenance item code(s) will blink.


4.


Press the select/reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to ‘‘100.’’


Maintenance Minder


TM


Important Maintenance Precautions If you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the correct maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed.


Your authorized Honda dealer knows your vehicle best and can provide competent, efficient service.


CONTINUED


345


2012 Accord Coupe


Maintenance Minder


TM


However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Make sure to have the service facility or person reset the display as previously described. Keep all receipts as proof of completion, and have the person who does the work fill out your Honda Service History or Canadian Maintenance Log. Check your warranty booklet for more information.


We recommend using Honda parts and fluids whenever you have maintenance done. These are manufactured to the same high quality standards as the original components, so you can be confident of their performance and durability.


346



U.S. Vehicles: According to state and federal regulations, failure to perform maintenance on the items marked with will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the information display.


Owner’s Maintenance Checks You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed.


Engine oil level time you fill the fuel tank. See page


Check every


291



Engine coolant level radiator reserve tank every time you fill the fuel tank. See page


Check the



292


Automatic transmission Check the fluid level monthly. See page 357



Brakes monthly. See page



Check the fluid level


362



Tires Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 379



Check the operation of


Lights all the lights monthly. See page 365


2012 Accord Coupe


Symbol


Maintenance Main Items


Replace engine oil * Replace engine oil and oil filter * Inspect front and rear brakes Check parking brake adjustment Inspect these items:


Tie rod ends, steering gear box, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS/VSA) All fluid levels and condition of fluids Exhaust system # Fuel lines and connections #



1 :


If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every year.



See information on maintenance and emissions warranty in the center column on page


346


NOTE:


Independent of the Maintenance Minder information, replace the brake fluid every 3 years.


Inspect idle speed every 160,000 miles (256,000 km).


Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.


Maintenance Minder


TM


Symbol


Maintenance Sub Items


Rotate tires Replace air cleaner element


If you drive in dusty conditions, replace every 15,000
miles (24,000 km).


Replace dust and pollen filter


If you drive primarily in urban areas that have high concentrations of soot in the air from industry and from diesel-powered vehicles, replace every 15,000 miles (24,000 km).


Inspect drive belt Replace transmission fluid Replace spark plugs Replace timing belt and inspect water pump (V6 engine only)


If you drive regularly in very high temperatures (over 110°F, 43°C), or in very low temperatures (under − (Canada).


29°C), replace every 60,000 miles (U.S.)/100,000 km



20°F,


Inspect valve clearance Replace engine coolant


347


2012 Accord Coupe


Fluid Locations


4-cylinder models


BRAKE FLUID (Black cap)


ENGINE OIL DIPSTICK (Orange handle)


POWER STEERING FLUID (Red cap)


WASHER FLUID (Blue cap)


ENGINE COOLANT RESERVOIR


348


CLUTCH FLUID (Manual Transmission only) (Light gray cap)


ENGINE OIL FILL CAP


AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop)


RADIATOR CAP


2012 Accord Coupe


V6 models


ENGINE OIL DIPSTICK (Orange loop)


POWER STEERING FLUID (Red cap)


WASHER FLUID (Blue cap)


ENGINE COOLANT RESERVOIR


Fluid Locations


BRAKE FLUID (Black cap)


CLUTCH FLUID (Manual Transmission only) (Light gray cap)


ENGINE OIL FILL CAP


AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop)


RADIATOR CAP


349


2012 Accord Coupe Recommended Engine Oil Oil is a major contributor to your engine’s performance and longevity. Always use a premium-grade 0W-20
detergent oil displaying the API Certification Seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements.


Adding Engine Oil


ENGINE OIL FILL CAP


ENGINE OIL FILL CAP


4-cylinder models


V6 models


Unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil slowly and carefully so you do not spill any. Clean up any spills immediately. Spilled oil could damage components in the engine compartment.


Reinstall the engine oil fill cap, and tighten it securely. Wait a few minutes, and recheck the oil level on the engine oil dipstick. Do not fill above the upper mark; you could damage the engine.


350


2012 Accord Coupe


Loading...
x