2009 Honda Accord Coupe Owners Manual

then to normal play.

You can also select the disc scan feature from the menu items with the selector knob (see page ).

155

To Stop Playing a Disc Press the eject button ( remove the disc. If you eject the disc, but do not remove it from the slot, the system will automatically reload the disc after 10 seconds and begin playing.

) to

You can also eject the disc when the ignition switch is off.

To play the radio when a disc is playing, press the AM, FM or XM (if equipped) button. Press the CD (CD/AUX on models with XM satellite radio) button again to switch back to the disc changer.

158

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４７：５４　３１ＴＥ０６１０　０１６４　

Playing Discs (Models without navigation system)

If you turn the system off while a disc is playing, either with the power/volume knob or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the disc will begin playing where it left off.

RemovingDiscsfromtheIn-dash DiscChanger To remove the disc currently in play, press the eject button. When a disc is removed from a slot, the system automatically begins the load sequence so you can load another disc in that position. If you do not remove the disc from the changer within 10 seconds, the disc will reload into the slot. Then the system returns to the previous mode (AM, FM, or XM Radio).

To remove a different disc from the changer, first select it with the appropriate preset button. When that disc begins playing, press the eject button. Continue pressing the eject button to remove all the discs from the changer.

You can also eject discs when the ignition switch is off. The disc that was last selected is ejected first.

Protecting Discs For information on how to handle and protect compact discs, see page 193

159

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４８：０３　３１ＴＥ０６１０　０１６５　

Disc Changer Error Message (Models without navigation system)

Error Message

Cause

Solution

HEAT ERROR

High Temperature

Track/File format not supported

Mechanical Error

UNSUPPORTED

BAD DISC

PLEASE CHECK

OWNER’S

MANUAL PUSH

EJECT

BAD DISC

PLEASE CHECK

Servo Error

OWNER’S MANUAL

Will disappear when the temperature returns to normal. Current track will be skipped. The next supported track or file plays automatically. Press the EJECT button and pull out the disc(s). Check the disc for serious damage, signs of deformation, excessive scratches, and/or dirt (see page 194). Insert the disc again. If the code does not disappear, or the disc(s) cannot be removed, consult your dealer. Do not try to force the disc out of the player.

The chart on the right explains the error messages you may see in the display while playing a disc.

If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For additional information on damaged discs, see page 194

The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.

160

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４８：１１　３１ＴＥ０６１０　０１６６　

Audio System (Models with navigation system)

Interface Dial Most audio system functions can still be controlled by standard buttons, dials, and knobs, but some functions can only be accessed using the interface dial. The interface dial has two parts, a knob and a selector.

KNOB

ENTER

Voice Control System The audio system can also be operated by voice control. See the Navi section in your quick start guide for an overview of this system, and the navigation system manual for complete details.

SELECTOR

The knob turns left and right. Use it to make selections or adjustments to a list or menu on the screen.

The selector can be pushed left, right, up, down, and in. Use the selector to scroll through lists, to select menus, and to highlight menu items. When you make a selection, push the center of the selector (ENTER) to go to that selection.

161

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４８：１７　３１ＴＥ０６１０　０１６７　

Playing the FM/AM Radio (Models with navigation system)

NAVIGATION SCREEN

POWER/VOLUME KNOB

CENTER DISPLAY

SOUND BUTTON

SKIP BAR SCAN/A.SEL (SCAN/AUTO SELECT) BAR

FM/AM BUTTON

CATEGORY BAR TUNE BAR

AUDIO BUTTON

U.S. model is shown.

162

INTERFACE DIAL

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４８：２７　３１ＴＥ０６１０　０１６８　

To Play the FM/AM Radio

STEREO ICON

BAND

The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Press the AUDIO button to view the audio control display. Turn the system on by pressing the power/volume knob or the FM/AM button. Adjust the volume by turning the power/volume knob.

The band and frequency that the radio was last tuned to are shown on the display. To change bands, press

Playing the FM/AM Radio (Models with navigation system)

the FM/AM button. You can also change bands by pushing the interface selector up. Each time you push it up, the band will change to FM1, FM2, or AM. On the FM bands, STEREO will be shown on the navigation screen and ST on the center display, if the station is broadcasting in stereo. Stereo reproduction on AM is not available.

To Select a Station You can use any of five methods to find radio stations on the selected band: tune, skip (seek), scan, the preset buttons, and auto select. On the FM band, you can also use the features provided by the radio data system (RDS). For more information on the RDS, see page 166

On the AM band, AM noise reduction turns on automatically.

CONTINUED

163

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４８：３５　３１ＴＥ０６１０　０１６９　

Playing the FM/AM Radio (Models with navigation system)

−

The skip (seek)

SKIP (SEEK) function searches up and down from the current frequency to find a station with a strong signal. To activate it, press either side (

or ) of the SKIP bar, then release

it. You can also activate the skip function (SEEK is displayed on the screen) by pushing the interface selector to the right or left.

SCAN ICON

−

The SCAN function

SCAN samples all stations with strong signals on the selected band. To activate it, press the SCAN side of the SCAN/A.SEL bar, then release it.

To scan with the interface dial, push the selector down, and then push it to the right. You will see SCAN flashing on the screen.

TUNE ICON

−

Use the TUNE bar to tune

TUNE the radio to a desired frequency. Press the right side of the bar to tune to a higher frequency, or the left side to tune to a lower frequency. To tune with the interface dial, push the selector down, and turn the knob to TUNE icon. Then press ENTER on the selector, and turn the knob to the desired frequency. To exit the TUNE mode, press ENTER on the selector, then push the selector up.

164

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４８：４６　３１ＴＥ０６１０　０１７０　

Playing the FM/AM Radio (Models with navigation system)

2.

3.

Use the tune, skip (seek), scan, or RDS function to tune the radio to a desired station.

Press the preset button, and hold it until you hear a beep. You can also store frequencies with the interface dial. Select the preset icon you want to store the frequency on, then press ENTER on the interface selector, and hold it for more than 2 seconds.

4.

Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.

The system will scan for a station with a strong signal. When it finds one, it will stop and play that station for about 10 seconds. If you do nothing, the system will then scan for the next strong station and play it for 10 seconds. When it plays a station that you want to listen to, press the scan side of the bar again, or push the interface selector to the right again.

−

Each preset button or

Preset preset icon can store one frequency on AM and two frequencies on FM.

Tostoreapresetmemorylocation: Select the desired band, AM or 1. FM. FM1 and FM2 let you store two sets of FM frequencies with the preset buttons (on-screen icons).

A.SEL INDICATOR

PRESET ICON

A.SEL ICON

−

If you are

AUTO SELECT traveling far from home and can no longer receive your preset stations, you can use the auto select feature to find stations in the local area.

Push the interface selector down to scroll down the screen, highlight A.SEL, then press ENTER on the interface selector. You will see A.SEL on the screen, and the system goes into scan mode for several seconds.

CONTINUED

165

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４８：５８　３１ＴＥ０６１０　０１７１　

Playing the FM/AM Radio (Models with navigation system)

Toturnoffautoselect, on the interface selector.

press ENTER

You can also press the A.SEL side of the SCAN/A.SEL bar. You will see A.SEL on the screen, and the system goes into scan mode for several seconds. The system stores the frequencies of six AM and twelve FM stations in the preset buttons.

You will see ‘‘0’’ displayed if auto select cannot find a strong station for every preset button. If you do not like the stations auto select has stored, you can store other frequencies on the preset buttons (icons) as previously described.

Toturnoffautoselect A. SEL side of the bar. This restores the presets you originally set.

, press the

For information on FM/AM radio frequencies and reception, see page 196

Radio Data System (RDS) On the FM band, you can select a favorite station and display the program service name according to the information provided by the radio data system (RDS).

ProgramService(PS)NameDisplay The program service name display function shows the name of the station you are listening to. With the audio system on and the FM band selected, you can turn this function on or off.

166

PS ON MESSAGE

To switch the PS name display function on and off, press and release the TITLE button. With the system on, you will see the ‘‘PS ON’’ message on the center display. If the station you are listening to is an RDS station, the displayed frequency switches to the station name.

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４９：１３　３１ＴＥ０６１０　０１７２　

Playing the FM/AM Radio (Models with navigation system)

RadioDataSystem(RDS)Category

If the station you are listening to is not an RDS station, the audio screen and the center display continue to show the frequency with the PS name display function on.

When you turn off this function by pressing the TITLE button, the center display shows ‘‘PS OFF.’’

RDS SEARCH ICON

With the FM band selected, you can select the program type provided by the RDS. Press the AUDIO button to display the radio information on the screen. Push down the selector on the interface dial, then turn the knob to select RDS SEARCH icon. Press ENTER to set your selection. The principal RDS categories are shown as follows:

ALL: All RDS category stations

ROCK: Rock, classic rock and soft rock music COUNTRY: Country music SOFT: Adult hits and soft music TOP 40: Top 40 hits OLDIES: Nostalgia music and oldies R & B: Rhythm and blues, and soft rhythm and blues RELIGION: Religious music and religious talk CLASSIC: Classical music JAZZ: Jazz INFO: News, information, sports, talk, foreign language, personality, public, college, and weather TRAFFIC: Traffic information

CONTINUED

167

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４９：２２　３１ＴＥ０６１０　０１７３　

Playing the FM/AM Radio (Models with navigation system)

RDS CATEGORY

RDS CATEGORY

U.S. model is shown.

▲ ▼

You can also select an RDS category with the CATEGORY bar. Press either side ( CATEGORY bar to display an RDS category in the center display. Select a category by pressing either side of the bar.

) of the

or

Turn the selector to select an RDS category. You can use the search or scan function to find radio stations on the selected RDS category by pressing the selector to the right repeatedly. Press ENTER to set your selection. If you do nothing while the RDS category is selected, the selected category is canceled.

168

RDSProgramSearch This function searches up and down a frequency for the strongest signal from the frequencies that carry the selected RDS category information. This can help you to find a station in your favorite category. To activate it, press and release either side will also see the selected RDS category name blinking in the center display while searching it. When the system finds a station, the selected RDS category name will be displayed again for about 5 seconds in the center display.

) of the SKIP bar. You

or

If the system does not find a station, ‘‘NOTHING’’ will be blinking for about 5 seconds, then the system goes back to the last selected station.

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４９：３０　３１ＴＥ０６１０　０１７４　

Playing the FM/AM Radio (Models with navigation system)

SEEK/SCAN ICON

Turn the knob to the desired RDS category.

While the RDS category is selected, move the selector knob to the right to select SEEK in the upper right corner of the screen. Then press ENTER to activate the seek function.

RDS CATEGORY LIST

SEEK is selected.

To activate RDS program search with the interface dial, push the AUDIO button to display the FM radio information on the screen. Push the selector down, and turn the knob to select RDS SEARCH icon. Press ENTER on the selector. The screen shows you the RDS category list.

RDSProgramSCAN The scan function samples all stations with strong signals on the selected RDS category. To activate it, press and release the SCAN side of the SCAN/A.SEL bar. You will see SCAN in the center display. The system will scan for a station with a strong signal in the selected RDS category. You will also see the selected RDS category name blinking in the center display while searching it. When the system finds one, it will stop and play that station for about 10 seconds.

CONTINUED

169

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４９：３８　３１ＴＥ０６１０　０１７５　

Playing the FM/AM Radio (Models with navigation system)

If you do nothing, the system will scan for the next strong station and play it for 10 seconds. When it plays a station that you want to listen to, press the SCAN side of the SCAN/ A.SEL bar again.

If the system does not find a station, ‘‘NOTHING’’ will be blinking for about 5 seconds, then the system goes back to the last selected station.

Turn the knob to the desired RDS category.

While the RDS category is selected, move the selector knob to the right to select SCAN in the upper right corner of the screen. Then press ENTER to activate the scan function.

You can use the RDS program search or scan function even if the PS name display function is off. In this case, the display shows a frequency in place of a PS name.

SEEK/SCAN ICON

RDS CATEGORY LIST

SCAN is selected.

To activate RDS program scan with the interface dial, push the AUDIO button to display the FM radio information on the screen. Push the selector down, and turn the knob to select RDS SEARCH icon. Press ENTER on the selector. The screen shows you the RDS category list.

170

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４９：４７　３１ＴＥ０６１０　０１７６　

RadioTextDisplay This function displays the radio text information of the selected RDS station.

If the selected RDS station has the radio text information, you will see the text indicator on the screen.

Playing the FM/AM Radio (Models with navigation system)

TEXT INDICATOR

RADIO TEXT ICON

The text is displayed according to the information from RDS.

To activate radio text display, use the interface dial. Push the selector down, and turn the knob to select RADIO TEXT icon. Press ENTER on the selector to enter the setting.

The display shows up to about 64
characters of text data on the selected RDS station.

171

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：４９：５６　３１ＴＥ０６１０　０１７７　

Playing the FM/AM Radio (Models with navigation system)

Adjusting the Sound BASS, TREBLE, FADER, and BALANCE are each adjustable. You can also adjust the strength of the sound coming from the subwoofer speaker. In addition, you can set the speed-sensitive volume compensation (SVC).

These adjustments can be made by the SOUND button or the interface dial.

172

SOUND ICON

To adjust them, press the AUDIO button, push the interface selector down, and turn the interface knob to SOUND. Then press ENTER on the selector.

Select the mode you want to adjust by turning the interface dial.

You can also adjust the sound by pushing the SOUND button repeatedly. Each mode is shown in the center display as it changes. Turn the power/volume knob to adjust the setting to your liking. When the level reaches the center, you will see ‘‘C’’ in the display.

The system will return to the audio playing mode in the center display about 10 seconds after you stop adjusting a mode.

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５０：０３　３１ＴＥ０６１０　０１７８　

Playing the FM/AM Radio (Models with navigation system)

−

To adjust the

SUBWOOFER strength of the sound from the subwoofer speaker, select it and press ENTER on the interface selector. Turn the interface knob to the desired level, and enter your selection by pressing ENTER on the interface selector.

−

To adjust bass BASS/TREBLE and treble, select BASS or TREBLE, and press ENTER on the interface selector. The current setting is shown on the display. Turn the interface knob to the desired level, and enter your selection by pressing ENTER on the interface selector.

−

FADER/BALANCE These modes adjust the strength of the sound coming from each speaker. Fader adjusts the front-to-back strength, while balance adjusts the side-to-side strength. To adjust fader and balance, select FADER or BALANCE, then press ENTER on the interface selector. The current setting is shown on the screen. Turn the interface knob to the desired level, and enter your selection by pressing ENTER on the interface selector. To equalize the fader or balance, turn the interface knob until the marks on the sound grid come to the center of the adjustment bar.

Speed-sensitiveVolume Compensation(SVC) The SVC mode controls the volume based on vehicle speed. The faster you go, the louder the audio volume becomes. As you slow down, the audio volume decreases.

The SVC has four modes; SVC OFF, SVC LOW, SVC MID, and SVC HIGH. The default setting is MID. To change the SVC mode, select SVC, then press ENTER on the interface selector. The current setting is shown on the screen. Turn the interface knob to the desired level, and enter your selection by pressing ENTER on the interface selector. If you feel the sound is too loud, choose low. If you feel the sound is too quiet, choose high.

173

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５０：１０　３１ＴＥ０６１０　０１７９　

Playing the XM Satellite Radio (Models with navigation system)

XM RADIO BUTTON

TITLE BUTTON PRESET BUTTONS CATEGORY BAR

POWER/VOLUME KNOB

SKIP BAR SCAN/A.SEL (SCAN/AUTO SELECT) BAR

TUNE BAR

AUDIO BUTTON

INTERFACE DIAL

U.S. model is shown.

174

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５０：１８　３１ＴＥ０６１０　０１８０　

Playing the XM Satellite Radio (Models with navigation system)

Your vehicle is capable of receiving XM Satellite Radio anywhere in the United States, and Canada, except Hawaii and Alaska. XM is a registered trademark of XM Satellite Radio, Inc.

XM Satellite Radio receives signals from two satellites to produce clear, high-quality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, XM Satellite Radio also allows you to view channel and category selections in the audio display.

Operating the XM Radio

Push the AUDIO button to display XM information on the screen. You can operate the XM Satellite Radio system with the interface dial.

To listen to XM satellite radio, turn the ignition switch to the ACCESSORY (I) or ON (II) position, and press the last channel you listened to will show in the audio screen and the center display. Adjust the volume by turning the power/volume knob.

button. The

CONTINUED

175

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５０：２５　３１ＴＥ０６１０　０１８１　

Playing the XM Satellite Radio (Models with navigation system)

−

Push down the

CHANNEL LIST interface selector to select AUDIO MENU, then turn the interface knob to select CHANNEL LIST and press ENTER on the selector. Turn the interface knob to select a channel, then press ENTER to set your selection.

On the screen, you will see the selected CHANNEL (number), CATEGORY, NAME (artist name), and TITLE (music title).

−

side of the

side for lower

Press either side of the

TUNE TUNE bar to change channel selections. Press the bar for higher numbered channels and the numbered channels. You can also change channels with the interface selector, push down the interface selector to select AUDIO MENU, then turn the interface knob to choose TUNE and press ENTER on the selector. Turn the interface knob to the appropriate direction. In the category mode, you can only select channels within that category.

−

To switch between the MODE category mode and channel mode, press and hold the TITLE button until the mode changes. The CATEGORY or CHANNEL mode is displayed on the screen. To switch the mode with the interface dial, push down the interface selector to select AUDIO MENU, then turn the knob to select MODE, and press ENTER on the selector repeatedly.

In the category mode, such as Jazz, Rock, Classical, etc., you can navigate through all of the channels within that category. In the channel mode, you can select all of the available channels.

Each time you press and release the TITLE button, the center display changes in the following sequence: NAME (artist name), TITLE (music title), and CHANNEL NAME (channel name).

176

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５０：３７　３１ＴＥ０６１０　０１８２　

Playing the XM Satellite Radio (Models with navigation system)

or

Press

▼ ▲ −

CATEGORY ( either side of the bar to select another category. You can also change a category by pushing the interface selector left or right.

−

The scan function gives

SCAN you a sampling of all channels while in the channel mode. In the category mode, only the channels within that category are scanned. To activate SCAN, press the SCAN side of the SCAN/A.SEL bar. To scan with the interface dial, scroll down, and push interface selector to the right. You will see SCAN on the screen and center display.

The system plays each channel in numerical order for a few seconds, then selects the next channel. When you hear a channel you want to continue listening to, push the interface selector to the right again or press the SCAN side of the bar to cancel.

XM BAND

−

You can store up to 12

Preset preset channels using the six preset buttons. Each button stores one channel from the XM1 band and one channel from the XM2 band.

To store a channel: 1.

button or scroll

Press the up by pushing the interface selector up. Either XM1 or XM2
will be shown on the display.

2.

Use the tune, skip (seek), or scan function to tune to a desired channel.

In category mode, only channels within that category can be selected. In channel mode, all channels can be selected.

3.

Pick the preset button you want for that channel. Press and hold the preset button until you hear a beep. You can also pick the number with the interface dial. Select your desired number and press and hold ENTER on the interface selector.

4.

Repeat steps 2 and 3 to store the first six channels.

CONTINUED

177

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５０：４７　３１ＴＥ０６１０　０１８３　

Playing the XM Satellite Radio (Models with navigation system)

XM Satellite Radio Display Messages ‘‘LOADING’’

−

XM is loading the audio or program information.

‘‘OFF AIR’’

−

The channel currently selected is no longer broadcasting.

‘‘NO SIGNAL’’

−

The signal is currently too weak. Move the vehicle to an area away from tall buildings, and with an unobstructed view of the southern horizon.

‘‘UPDATING’’

−

The encryption code is being updated. Wait until the encryption code is fully updated. Channels 0 and 1
should still work normally.

‘‘ - - - - ’’

−

The selected channel number does not exist, or is not part of your subscription, or this channel has no artist or title information at this time.

‘‘ANTENNA’’

There is a problem

− with the XM antenna. Please consult your dealer.

5.

Press the button or scroll up again. The other XM band will be shown. Store the next six channels using steps 2 and 3.

Once a channel is stored, press and release the proper preset button to tune to it.

178

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５０：５５　３１ＴＥ０６１０　０１８４　

Playing the XM Satellite Radio (Models with navigation system)

Signal may be blocked by mountains or large obstacles to the south.

Signal weaker in these areas.

SATELLITE

The XM satellites are in orbit over the equator; therefore, objects south of the vehicle may cause satellite reception interruptions. To help compensate for this, ground-based repeaters are placed in major metropolitan areas. Satellite signals are more likely to be blocked by tall buildings and mountains the farther north you travel from the equator.

Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions:

Driving on the north side of an east/west mountain road.

Driving on the north side of a large commercial truck on an east/west road.

GROUND REPEATER

Driving in tunnels.

CONTINUED

179

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５１：０５　３１ＴＥ０６１０　０１８５　

Playing the XM Satellite Radio (Models with navigation system)

Driving on a road beside a vertical wall, steep cliff, or hill to the south of you.

Driving on the lower level of a multi-tiered road.

Driving on a single lane road alongside dense trees taller than 50 ft. (15 m) to the south of you.

There may be other geographic situations that could affect XM Satellite Radio reception.

AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

180

Receiving XM Satellite Radio Service If your XM Satellite Radio service has expired or you purchased your vehicle from a previous owner, you can listen to a sampling of the broadcasts available on XM Satellite Radio. With the ignition switch in the ACCESSORY (I) or the ON (II) position, press the button. A variety of music types and styles will play.

, or at

www.xmradio.com

If you decide to purchase XM satellite radio service, contact XM Radio at 1-800-852-9696. In Canada, contact , or call 1-877-438- www.xmradio.ca 9677. You will need to give them your radio I.D. number and your credit card number. To get your radio I.D. number, press and release the side of the TUNE bar until ‘‘0’’ appears in the display. Your I.D. will appear in the display.

After you’ve registered with XM Radio, keep your audio system in the XM Satellite Radio mode while you wait for activation. This should take about 30 minutes.

While waiting for activation, make sure your vehicle remains in an open area with good reception. Once your audio system is activated, CAT (category) or CH (channel) will appear in the center display, and you’ll be able to listen to XM Radio broadcasts. XM Radio will continue to send an activation signal to your vehicle for at least 12 hours from the activation request. If the service has not been activated after 36 hours, contact XM Radio.

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５１：１３　３１ＴＥ０６１０　０１８６　

Playing Discs (Models with navigation system)

CENTER DISPLAY

TITLE BUTTON PRESET BUTTONS

DISC LOAD BUTTON

U.S. model is shown.

AUDIO BUTTON

INTERFACE DIAL

NAVIGATION SCREEN

POWER/VOLUME KNOB

CD BUTTON

SKIP BAR SCAN/A.SEL (SCAN/AUTO SELECT) BAR

DISC EJECT BUTTON

DISC SLOT

CONTINUED 181

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５１：２６　３１ＴＥ０６１０　０１８７　

Playing Discs (Models with navigation system)

The disc packages or jackets should have one of these marks.

Your vehicle’s audio system has an in-dash disc changer with the same controls used for the radio. To operate the disc changer, the ignition switch must be in the ACCESSORY (I) or the ON (II) position.

The disc changer can play these disc formats:

CD (CD-DA) MP3/WMA

The changer can also play MP3 or WMA format (see page

188

).

When playing a disc in MP3, you will see ‘‘MP3’’ in the display. In WMA format, ‘‘WMA’’ will appear in the display.

182

NOTE: If a file on an MP3 or WMA disc is protected by digital rights management (DRM), the audio system displays UNSUPPORTED in the center display, and then skips to the next file.

Video CDs and DVDs will not work in this unit.

Some CD-DA and CD-ROM mixed discs are not playable.

You cannot load and play 3-inch (8-cm) discs in this system.

Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５１：３９　３１ＴＥ０６１０　０１８８　

Playing Discs (Models with navigation system)

Loading Discs in the Changer To load multiple discs in one operation:

1.

2.

3.

With the ignition in the ACCESSORY (I) or the ON (II) position, press and hold the LOAD button until you hear a beep and see ‘‘LOAD’’ in the center display, then release the button.

Insert a disc into the slot. Insert it only about halfway; the drive will pull it in the rest of the way. You will see ‘‘BUSY’’ in the center display. When you insert the first disc, the changer will start to play the disc.

When ‘‘LOAD’’ appears in the center display again, insert the next disc into the slot. Do not try to insert a disc until ‘‘LOAD’’ appears. You could damage the audio unit.

4.

Repeat this until all six positions are loaded. If you are not loading all six positions, the system will then begin playing the last disc loaded.

If you stop loading discs before all six positions are filled, the system will wait for 10 seconds, stop the load operation, and begin playing the last disc loaded.

To load a single disc: 1.

Press and release the LOAD button.

2.

‘‘NO DISC’’ is shown on the screen for an empty position in the changer. When the green load indicator comes on and you see ‘‘LOAD’’ in the center display, insert the disc into the slot. Insert it only about halfway; the drive will pull it in the rest of the way.

Do not try to insert a disc until ‘‘LOAD’’ appears. You could damage the audio unit.

You can select the position to load a disc. Turn the interface knob or press a preset button to select the position, then press ENTER on the selector. This starts the loading sequence. If you do not select the position, the system loads the disc to the first empty position in numerical order.

If you press the LOAD button while a disc is playing, the system will stop playing that disc and start the loading sequence. It will then play the disc just loaded.

183

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５１：４７　３１ＴＥ０６１０　０１８９　

Playing Discs (Models with navigation system)

The player can play CD-TEXT, MP3, and WMA formats.

When you play CD-TEXT, you will see the track name, artist name, and album name on the screen. When you play MP3/WMA discs, you will see the track name and folder name on the screen. If the disc was not recorded with this information, it will not be displayed.

To Change Tracks Each time you press and release the side of the skip bar or push the

interface selector to the right, the player skips forward to the beginning of the next track. Press and release the side of the skip bar or push the interface selector to the left to skip backward to the beginning of the current track. Press the side or push the interface selector to the left again to skip to the previous track. To move rapidly within a track, press and hold either side of the skip bar.

To Play a Disc

CURRENT DISC

Select the changer by pressing the CD button. The system will begin playing the last selected disc in the disc changer. You will see the current disc position highlighted.

To select a different disc, press the corresponding number on the preset buttons, or turn the interface knob to highlight the desired disc number, then press ENTER on the interface selector.

184

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５１：５７　３１ＴＥ０６１０　０１９０　

To Choose a Track

TRACK LIST

You can also choose a track directly from a track list. Press ENTER on the interface selector, and the track list screen will be shown. If there are no track names, track numbers are displayed. You will see the current track is highlighted. Turn the interface knob to select the desired track, then press ENTER on the interface selector.

Playing Discs (Models with navigation system)

To exit the track list display, press the AUDIO button, or push the interface selector to the left.

Track Scan When you press the SCAN side of the SCAN/A. SEL bar or scroll down and push the interface selector to the left, the next track of the current track plays for about 10 seconds. You will see SCAN next to TRACK on the screen and center display. To listen to the rest of the track, press and hold the SCAN side of the bar until you hear a beep or push the interface selector to the left again within 10 seconds.

If you don’t, the system advances to the next track, plays about 10
seconds of it, and continues through the rest of the tracks the same way.

Disc Scan When you press the SCAN side of the SCAN/A. SEL bar repeatedly until you see D-SCAN in the center display, or push down the interface selector to the right, the first track of the current disc plays for about 10
seconds. You will see SCAN next to DISC on the screen. The disc number is blinking and SCAN is also shown in the center display. To listen to the rest of the disc, press and hold the SCAN side of the bar until you hear a beep, or push down the interface selector to the right again within 10 seconds.

If you don’t, the system advances to the next disc, plays about 10 seconds of its first track, and continues through the rest of the discs the same way. When the system reaches the last disc, DISC SCAN is canceled, and that disc continues to play.

185

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５２：０６　３１ＴＥ０６１０　０１９１　

Playing Discs (Models with navigation system)

To Select Repeat or Random Mode:

Push down the selector.

AUDIO MENU SCREEN

You can select any type of repeat and random modes by using the interface dial. Push the AUDIO button to display the audio information on the screen, then scroll down by pushing down the selector to select the audio menu.

Turn the interface knob to select a desired repeat or random mode, then press ENTER to set your selection.

To cancel the selected repeat or random mode, have the selected mode highlighted, then press ENTER on the interface selector.

186

Track Repeat To replay the current track continuously, select TRACK REPEAT, and press ENTER on the interface selector. As a reminder, you will see REPEAT next to TRACK on the screen. To turn this feature off, highlight TRACK REPEAT (if not already highlighted), and press ENTER on the interface selector again.

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５２：１５　３１ＴＥ０６１０　０１９２　

Playing Discs (Models with navigation system)

Disc Repeat To replay the current disc continuously, select DISC REPEAT, and press ENTER on the interface selector. As a reminder, you will see REPEAT next to DISC on the screen. To turn this feature off, highlight DISC REPEAT (if not already highlighted), and press ENTER on the interface selector again.

Random Play To play the tracks on the current disc in random order, select TRACK RANDOM, and press ENTER on the interface selector. As a reminder, you will see RANDOM next to TRACK on the screen. To turn this feature off, highlight TRACK RANDOM (if not already highlighted), and press ENTER on the interface selector again.

To Stop Playing a Disc To take the system out of disc mode, press the FM/AM button, the

button, or the AUX button (if an appropriate unit is connected). To return to disc mode, press the CD button.

If you turn the system off while a disc is playing, either with the power/volume knob or the ignition switch, play will continue at the same point when you turn it back on.

187

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５２：２８　３１ＴＥ０６１０　０１９３　

Playing Discs (Models with navigation system)

Changing the Folders While playing an MP3/WMA disc, you can select a folder within the disc by pressing either side of the category bar. Each time you press either side of the bar, the folder title and its first file’s information appear in the center display in recorded order.

−

The specifications for compatible WMA files are: −

Sampling frequency: 22.05/32/44.1/48 kHz Bitrate: 32/40/48/64/80/96/128/160/192
kbps Compatible with variable bitrate and multi-session Maximum layers (including ROOT): 8 layers

−

To play an MP3/WMA disc, use the disc controls previously described, along with the following information.

Playing an MP3/WMA Disc The changer plays MP3/WMA files in recorded order. Each disc can hold up to 400 playable files within 8
folder layers. When playing MP3
discs, a disc can support a maximum number of 100 folders, and each folder can hold 255 playable files.

−

The specifications for compatible MP3 files are: −

Sampling frequency: 32/44.1/48 kHz (MPEG1) 16/22.05/24 kHz (MPEG2) Bitrate: 32/40/48/56/64/80/96/112/128/ 160/192/224/256/320 kbps (MPEG1) 8/16/24/32/40/48/56/64/80/96/ 112/128/160 kbps (MPEG2) Compatible with variable bitrate and multi-session Maximum layers (including ROOT): 8 layers

−

188

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５２：３８　３１ＴＥ０６１０　０１９４　

ChangingandSelectingtheFolders/ Files

Playing Discs (Models with navigation system)

MP3/WMA INDICATOR

CURRENT FOLDER

Using the interface selector, you can see the list of all the files and folders within a disc. While playing a MP3/ WMA disc, press the AUDIO button. The currently playing folder and file information comes on the screen.

Push the selector to show the folder list. Turn the selector knob, highlight the folder you want to see the information within, and press ENTER.

CURRENT TRACK

You can see the list of all the files in the selected folder. Turn the selector knob, then press ENTER to set your selection.

If the main folder has some additional folders in the lower layer, you can also see each lower folder listed on the screen.

189

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５２：４７　３１ＴＥ０６１０　０１９５　

Playing Discs (Models with navigation system)

Folder Scan This feature, when activated, samples the first file in each folder for 10 seconds. To scan a folder, press the SCAN side of the SCAN/ A. SEL bar repeatedly. You will see SCAN next to FOLDER and the folder number blinking.

To listen to the rest of the folder, press and hold the SCAN side of the bar until you hear a beep. If you do nothing, the system advances to the next folder, plays 10 seconds of it, and continues throughout the rest of the folder in the same way. When the system samples the first file in all folders, folder scan is canceled, and the last file played continues to play.

Folder Repeat This feature, when activated, replays all files in the selected folder. To activate folder repeat mode, select FOLDER REPEAT by interface knob, and press ENTER on the interface selector. You will see REPEAT next to FOLDER on the screen. To turn this feature off, highlight FOLDER REPEAT (if not already highlighted), and press ENTER on the interface selector again.

Folder Random This feature, when activated, plays all files in the current folder in random order. To activate folder random play, select FOLDER RANDOM by interface knob, and press ENTER on the interface selector. You will see RANDOM next to FOLDER on the screen. To turn this feature off, highlight FOLDER RANDOM (if not already highlighted), and press ENTER on the interface selector again.

To select any type of the repeat modes, use the interface dial. For more information, see page

186

To select any type of the random modes, use the interface dial. For more information, see page

186

190

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５２：５５　３１ＴＥ０６１０　０１９６　

Playing Discs (Models with navigation system)

Removing Discs from the Changer To remove the disc that is currently playing, press the eject button. You will see ‘‘EJECT’’ in the center display. When you remove the disc from the slot, the system automatically enters the previous mode AM, FM1, FM2, or XM Satellite Radio. The system also begins the load sequence so you can load another disc. If you do not load another disc, the load sequence is canceled, and the system continues playing in the previous mode.

If you do not remove the disc from the slot, the system will reload the disc after 10 seconds. To begin playing the disc, press the CD button.

To remove a different disc from the changer, first select it by pressing the corresponding number on the preset button or turning the interface knob, and pressing ENTER on the interface selector. When that disc begins playing, press the eject button.

When you press the eject button while listening to the radio, or with the audio system turned off, the disc that was last selected is ejected. After that disc is ejected, pressing the eject button again will eject the next disc in numerical order. By doing this six times, you can remove all the discs from the changer.

You can also eject discs when the ignition switch is off: To eject one disc, press and release the eject button. To eject all discs, press and hold the eject button until you hear a beep.

191

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５３：０３　３１ＴＥ０６１０　０１９７　

Disc Changer Error Messages (Models with navigation system)

Error Message

Cause

Solution

HEAT ERROR

High Temperature

Track/File format not supported

Mechanical Error

UNSUPPORTED

BAD DISC

PLEASE CHECK

OWNER’S

MANUAL PUSH

EJECT

BAD DISC

PLEASE CHECK

Servo Error

OWNER’S MANUAL

Will disappear when the temperature returns to normal. Current track will be skipped. The next supported track or file plays automatically. Press the EJECT button and pull out the disc(s). Check the disc for serious damage, signs of deformation, excessive scratches, and/or dirt (see page 194). Insert the disc again. If the code does not disappear, or the disc(s) cannot be removed, consult your dealer. Do not try to force the disc out of the player.

The chart on the right explains the error messages you may see in the center display while playing a disc.

If you see an error message in the center display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For additional information on damaged discs, see page 194

The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.

192

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５３：１３　３１ＴＥ０６１０　０１９８　

General Information

When using CD-R or CD-RW discs, use only high quality discs labeled for audio use.

When recording a CD-R or CD-RW, the recording must be closed for it to be used by the disc changer.

Play only standard, round, 5-inch (12 cm) discs. Smaller or odd- shaped discs may jam in the drive or cause other problems.

Handle your discs properly to prevent damage and skipping.

Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.

Protecting Discs When a disc is not being played, store it in its case to protect it from dust and other contamination. To prevent warpage, keep discs out of direct sunlight and extreme heat.

To clean a disc, use a clean soft cloth. Wipe across the disc from the center to the outside edge.

A new disc may be rough on the inner and outer edges. The small plastic pieces causing this roughness can flake off and fall on the recording surface of the disc, causing skipping or other problems. Remove these pieces by rubbing the inner and outer edges with the side of a pencil or pen.

Never try to insert foreign objects in the disc changer.

Protecting Your Discs

Handle a disc by its edges; never touch either surface. Do not place stabilizer rings or labels on the disc. These, along with contamination from finger prints, liquids, and felt- tip pens, can cause the disc to not play properly, or possibly jam in the drive.

193

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５３：２６　３１ＴＥ０６１０　０１９９　

Protecting Your Discs

Additional Information on Recommended Discs The in-dash disc player/changer has a sophisticated and delicate mechanism. If you insert a damaged disc as indicated in this section, it may become stuck inside and damage the audio unit.

Examples of these discs are shown to the right:

194

1.

Bubbled, wrinkled, labeled, and excessively thick discs

Bubbled/ Wrinkled

With Label/ Sticker

Using Printer Label Kit

Sealed

With Plastic Ring

2.

Damaged discs

3.

Poor quality discs

Chipped/ Cracked

Warped

Burrs

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５３：３８　３１ＴＥ０６１０　０２００　

4.

Small, irregular shaped discs

5.

Discs with scratches, dirty discs

3-inch (8-cm) CD

Triangle Shape

Fingerprints, scratches, etc.

CD-R or CD-RW may not play due to the recording conditions.

Scratches and fingerprints on the discs may cause the sound to skip.

Can Shape

Arrow Shape

Protecting Your Discs

Recommended discs are printed with the following logo.

Audio unit may not play the following formats.

This audio unit cannot play a Dual- disc .

195

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５３：４８　３１ＴＥ０６１０　０２０１　

FM/AM Radio Reception

FM/AM Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequen- cies:

AM band: 530 to 1,710 kHz FM band: 87.7 to 107.9 MHz

Radio stations on the AM band are assigned frequencies at least 10 kHz apart (530, 540, 550). Stations on the FM band are assigned frequencies at least 0.2 MHz apart (87.9, 88.1, 88.3).

Stations must use these exact frequencies. It is fairly common for stations to round-off the frequency in their advertising, so your radio could display a frequency of 100.9 even though the announcer may identify the station as ‘‘FM101.’’

196

Radio Reception How well the radio receives stations is dependent on many factors, such as the distance from the station’s transmitter, nearby large objects, and atmospheric conditions.

A radio station’s signal gets weaker as you get farther away from its transmitter. If you are listening to an AM station, you will notice the sound volume becoming weaker, and the station drifting in and out. If you are listening to an FM station, you will see the stereo indicator flickering off and on as the signal weakens. Eventually, the stereo indicator will go off and the sound will fade completely as you get out of range of the station’s signal.

Driving very near the transmitter of a station that is broadcasting on a frequency close to the frequency of the station you are listening to can also affect your radio’s reception. You may temporarily hear both stations, or hear only the station you are close to.

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５３：５５　３１ＴＥ０６１０　０２０２　

FM/AM Radio Reception

AsrequiredbytheFCC: Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

197

Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station’s transmitter, and the deflected signal. This causes the sound to distort or flutter. This is a main cause of poor radio reception in city driving.

Radio reception can be affected by atmospheric conditions such as thunderstorms, high humidity, and even sunspots. You may be able to receive a distant radio station one day and not receive it the next day because of a change in conditions.

Electrical interference from passing vehicles and stationary sources can cause temporary reception problems.

2009 Accord Coupe Table Of ContentsMain Menu０８／０６／１１　１８：５４：０３　３１ＴＥ０６１０　０２０３　

Remote Audio Controls

MODE BUTTON

VOL BUTTON

CH BUTTON

Three controls for the audio system are mounted in the steering wheel hub. These let you control basic functions without removing your hand from the wheel.

198

▲

) or down (

The VOL button adjusts the volume up ( ). Press the top or bottom of the button, hold it until the desired volume is reached, then release it.

▼

The MODE button changes the mode. Pressing the button repeatedly selects FM1, FM2, AM, or disc (if a disc(s) is loaded). On models with satellite radio system, you can also select XM1 and XM2.

＋

If you are listening to the radio, use the CH button to change stations. Each time you press the top ( ) of the button, the system goes to the next preset station on the band you are listening to. Press the bottom − station. If you press and hold the CH button ( ), the system goes into the skip (seek) mode. It stops when it finds a station with a strong signal.

) to go back to the previous

) or (

＋

−

If you are playing a disc, the system skips to the beginning of the next track (file in MP3 or WMA format) each time you press the top ( ) of ＋ the CH button. Press the bottom − current track/file. Press it twice to return to the previous track/file.