2008 Honda Accord Coupe Owners Manual

NOTE: speed quickly, use the brakes as you normally would.

Press and hold the SET/DECEL button. Release the button when you reach the desired speed.

To slow down in very small amounts, tap the SET/DECEL button repeatedly. Each time you do this, your vehicle will slow down about 1 mph (1.6 km/h).

Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL indicator on the instrument panel will go out. When the vehicle slows to the desired speed, press the SET/ DECEL button.

CONTINUED

211

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３５：５５　３１ＴＥ０６００　０２１７　

Cruise Control

Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The vehicle will return to the set cruising speed.

Resting your foot on the brake or clutch pedal causes the cruise control to cancel.

Canceling Cruise Control You can cancel cruise control in any of these ways:

Tap the brake or clutch pedal.

Push the CANCEL button on the steering wheel.

Push the CRUISE button on the steering wheel.

Resuming the Set Speed When you push the CANCEL button, or tap the brake or clutch pedal, the system will remember the previously set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h), and then press and release the RES/ACCEL button. The CRUISE CONTROL indicator comes on. The vehicle will accelerate to the same cruising speed as before.

Pressing the CRUISE button turns the system completely off and erases the previous cruising speed.

212

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３６：０４　３１ＴＥ０６００　０２１８　

HomeLink Universal Transceiver

AllV6models The HomeLink universal transceiver built into your vehicle can be programmed to operate up to three remotely controlled devices around your home, such as garage doors, lighting, or home security systems.

General Information Before programming your HomeLink to operate a garage door opener, confirm that the opener has an external entrapment protection system, such as an ‘‘electronic eye,’’ or other safety and reverse stop features.

If your garage door was manufactured before April 1, 1982, you may not be able to program HomeLink to operate it. These units do not have safety features that cause the motor to stop and reverse it if an obstacle is detected during closing, increasing the risk of injury.

Do not use HomeLink with any garage door opener that lacks safety stop and reverse features.

Units manufactured between April 1, 1982 and January 1, 1993 may be equipped with safety stop and reverse features. If your unit does not have an external entrapment protection system, an easy test to confirm the function and performance of the safety stop and reverse feature is to lay a 2
under the closing door. The door should stop and reverse upon contacting the piece of wood.

×

As an additional safety feature, garage door openers manufactured after January 1, 1993 are required to have external entrapment protection systems, such as an electronic eye, which detect an object obstructing the door.

Important Safety Precautions Refer to the safety information that came with your garage door opener to test that the safety features are functioning properly. If you do not have this information, contact the manufacturer of the equipment. Before programming HomeLink to a garage door or gate opener, make sure that people and objects are out of the way of the device to prevent potential injury or damage. When programming a garage door opener, park just outside the garage.

213

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３６：１２　３１ＴＥ０６００　０２１９　

HomeLink Universal Transceiver

−

If you just

Training HomeLink Beforeyoubegin received your vehicle and have not trained any of the buttons in HomeLink before, you should erase any previously learned codes before training the first button. To do this, press and hold the two outside buttons on the HomeLink transceiver for about 10 20 seconds, − until the red indicator flashes. Release the buttons, then proceed to step 1.

If you are training the second or third buttons, go directly to step 1.

1.

Hold the end of the garage door opener remote transmitter 1 to 3
inches from HomeLink. Make sure you are not blocking your view of the red indicator in HomeLink.

214

transmitter may stop transmitting after a short time. Go to step 3.

3.

Press and hold the remote transmitter button and one of the HomeLink buttons at the same time. While continuing to hold the HomeLink button, press and release the remote transmitter button every 2 seconds.

If the red indicator in HomeLink begins to flash slowly at first, then rapidly, release both buttons, and go to step 4.

If the red indicator in HomeLink continues to flash slowly (does not begin to flash rapidly), repeat steps 1 thru 3.

RED INDICATOR

2.

Press and hold the remote transmitter button and one of the HomeLink buttons at the same time.

If the red indicator in HomeLink begins to flash slowly at first, then rapidly, release both buttons, and go to step 4.

If the red indicator in HomeLink continues to flash slowly (does not flash rapidly), your remote

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３６：２２　３１ＴＥ０６００　０２２０　

HomeLink Universal Transceiver

6.

Repeat these steps to train the other two HomeLink buttons to operate any other compatible remotely controlled devices around your home (lighting, automatic gate, security system, etc.).

4.

Test the HomeLink button by pushing it for about 1 second.

If the button works, programming is complete.

If the button does not work go to step 5.

5.

Push and hold the HomeLink button and watch the red indicator on HomeLink.

If the indicator stays on, press the HomeLink button again; the remotely controlled device should operate.

If the indicator flashes rapidly for 2 seconds then stays on, you have a rolling code transmitter: go to ‘‘Training with a Rolling Code System.’’

Training With a Rolling Code System For security purposes, newer garage door opening systems use a ‘‘rolling’’ or variable code. Information from the remote control and the garage door opener is needed before HomeLink can operate the garage door opener.

The ‘‘Training HomeLink’’ procedure trains HomeLink to the proper garage door opener code. The following procedure synchronizes HomeLink to the garage door opener so it sends and receives the correct codes.

1.

Make sure you have properly completed the ‘‘Training HomeLink’’ procedure.

CONTINUED

215

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３６：３１　３１ＴＥ０６００　０２２１　

HomeLink Universal Transceiver

2.

Find the ‘‘learn’’ button on your garage door opener unit. The location will vary, depending on the manufacturer.

LEARN BUTTON

4.

Press and hold the button on HomeLink for 3 to 4 seconds.

5.

Press the HomeLink button again for about 1 second. It should operate the garage door.

Erasing Codes To erase the codes stored in all three buttons, press and hold the two outside buttons until the red indicator begins to flash, then release the buttons.

You should erase all three codes before selling the vehicle.

Retraining a Button If you want to retrain a programmed button for a new device, you do not have to erase all button memory. You can replace the existing memory code using this procedure:

1.

Press and hold the HomeLink button to be trained until the HomeLink indicator begins to flash slowly.

3.

Press the learn button on the garage door opener unit until the indicator next to the button comes on. The indicator may blink, or come on and stay on. You then have approximately 30 seconds to complete the following steps.

216

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３６：３８　３１ＴＥ０６００　０２２２　

HomeLink Universal Transceiver

If a rolling code transmitter was previously programmed, the indicator will flash rapidly for 2
seconds, and then stay on for about 23 seconds.

If a standard transmitter was programmed, the indicator will stay on for about 25 seconds.

2.

Once the HomeLink indicator begins to flash slowly, continue to hold the HomeLink button, and follow steps 2 thru 5 under ‘‘Training HomeLink’’ (see page 214

).

Customer Assistance If you have problems with training the HomeLink Universal Transceiver, or would like information on home products that can be operated by HomeLink, call (800) 355-3515. On the Internet, go to www.homelink.com.

HomeLink is a registered trademark of Johnson Controls, Inc.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

217

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３６：４８　３１ＴＥ０６００　０２２３　

Bluetooth HandsFreeLink

Onmodelswithnavigationsystem Your vehicle is equipped with the Bluetooth HandsFreeLink (HFL). HFL uses Bluetooth technology to link your cellphone to your vehicle. With HFL, you can place and receive calls through your vehicle’s audio system, without the distraction of handling your cellphone. To use this feature, you need a Bluetooth- compatible cellphone with the Hands Free Profile. For more information, and a list of compatible cellphones, visit , or call (888) 528-7876. In Canada, visit honda.ca The HFL is available in both English and French (Canadian models only). To change the language, see page 243

, or call (888) 9-HONDA-9.

handsfreelink.honda.com

www.

Here are the main features of the HFL. Instructions for using the HFL begin on page

228

218

, or by calling

handsfreelink.honda.com the Hands Free Link consumer support at (888) 528-7876. In Canada, visit HONDA-9.

, or call (888) 9-

www.honda.ca

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Honda Motor Co., Ltd. is under license. Other trademarks and trade names are those of their respective owners.

Incoming/Outgoing Calls With a linked phone, the HFL allows you to send and receive calls in your vehicle without holding the phone.

Voice Control HFL recognizes simple voice commands, such as phone numbers and names. It uses these commands to automatically dial, receive, and store numbers. For more information on voice control, see Using Voice Control on page 221

Bluetooth Wireless Technology Bluetooth is a registered trademark of Bluetooth SIG, Inc. Bluetooth is the wireless technology that links your phone to the HFL. The HFL uses a Class 2 Bluetooth, which means the maximum range between your phone and vehicle is 30 feet (10 meters).

To use the HFL, your phone must have approved Bluetooth capability along with the Hands Free Profile. This type of phone is available through many phone makers and cellular carriers. You can also find an approved phone by visiting

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３６：５９　３１ＴＥ０６００　０２２４　

Phonebook The HFL can store up to 50 names and phone numbers in its phonebook. With a linked phone, you can then automatically dial any name or number in the phonebook.

Your vehicle’s HFL system has the cellular phonebook import function. This allows you to import your cellular phonebook to the HFL. Using the navigation system, you can make a call directly and store a desired number in the HFL from the list shown on the navigation display. For more information on how to import the phonebook or to make a call, see page

228

You can also store the desired number to the HFL directly from your cellphone using the receive contact function in the HFL.

Microphone The HFL microphone is on the ceiling, between the front spotlights. The microphone is shared with the navigation system.

Audio System When the HFL is in use, the sound comes through the vehicle’s front audio system speakers. If the audio system is in use while operating either of the HFL buttons or making a call, the HFL over-rides the audio system. To change the volume level, use the audio system volume knob, or the steering wheel volume controls.

Bluetooth HandsFreeLink

HFL Buttons

HFL TALK BUTTON

HFL BACK BUTTON

To operate the HFL, use the HFL Talk and Back buttons on the left side of the steering wheel.

The HFL buttons are used as follows:

HFL Talk: This button is used before you give a command, to answer incoming calls, and to confirm system information.

CONTINUED

219

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３７：０６　３１ＴＥ０６００　０２２５　

Bluetooth HandsFreeLink

Press and release the button, then wait for a beep before giving a command.

HFL Back: This button is used to end a call, go back to the previous voice control command, and to cancel an operation.

Information Display

’’ indicator will be displayed on

‘‘ the center display if your phone is linked to the Bluetooth compatible cell phone.

BLUETOOTH INDICATOR

When you are operating the HFL, dialing or receiving calls with the audio system in use, you will see the above screen on the navigation display.

You will also see ‘‘HANDS FREE LINK’’ on the center display.

220

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３７：１６　３１ＴＥ０６００　０２２６　

Bluetooth HandsFreeLink

How to Use the HFL The HFL is operated by the HFL Talk and Back buttons on the left side of the steering wheel. The next few pages provide instructions for all basic features of the HFL.

All phones may not

NOTE: operate identically, and some may cause inconsistent operation of the HFL.

Using Voice Control Here are some guidelines for using voice control:

After pressing the Talk button, wait for the beep, then give a voice command.

Adjust the airflow from both the dashboard and side vents so they do not blow against the microphone on the ceiling.

Close the windows and the moonroof.

Give a voice command in a clear natural speaking voice without pausing between words or numbers. If the system cannot recognize your command because of the background noise, speak louder.

To enter a command, press and release the Talk button. Then, after the beep, say your command in a clear, natural tone.

If the microphone picks up voices other than yours, the system may not interpret your voice commands correctly.

Lower the A/C fan speed during voice recognition operation.

If the HFL does not recognize a command, its response is, ‘‘Pardon.’’ If it doesn’t recognize the command a second time, its response is, ‘‘Please repeat.’’ If it doesn’t recognize the command a third time, it plays the Help prompt.

CONTINUED

221

2008 Accord Coupe Table Of ContentsMain MenuWhen you finish a command sequence, the HFL goes back to its main menu. For example, when you store the name, ‘‘Eric,’’ the HFL response is, ‘‘Eric has been stored.’’ The next time you press the Talk button, you will be at the main menu.

０７／０８／０６　１２：３７：２４　３１ＴＥ０６００　０２２７　

Bluetooth HandsFreeLink

To hear a list of available options at any time, press the Talk button, wait for the beep, and say, ‘‘Hands free help.’’

Many commands can be spoken together. For example, you can say, ‘‘Dial 123-456-7891.’’

To enter a string of numbers in a Call or Dial command, you can say them all at once, or you can separate them in blocks of 3, 4, 7, 10, and 11.

To skip a voice prompt, press the Talk button while the HFL is speaking. The HFL will then begin listening for your next command.

To go back one step in a command process, say, ‘‘Go back,’’ or press the Back button. If nothing is said while the HFL is listening for a command, the HFL will time out and stop its voice recognition. The next time you press the Talk button, the HFL begins listening from the point at which it timed out.

To end a command sequence at any time, press and hold the Back button, or press and release the Talk button, wait for the beep, and say, ‘‘Cancel.’’ The next time you press the Talk button, the HFL begins from its main menu.

222

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３７：３３　３１ＴＥ０６００　０２２８　

Setting Up the System The voice of the HFL can be set to male or female (U.S. models only). Also, the incoming notification can be set to a ring tone, a prompt, or no notification.

Tosetupthesystem,dothis: 1.

Press and release the Talk button. After the beep, say ‘‘System.’’ The HFL response is, ‘‘System options are setup and clear.’’

2.

Press and release the Talk button. After the beep, say ‘‘Setup.’’ The HFL response is ‘‘Would you like male or female prompts?’’

3.

4.

Press and release the Talk button. After the beep, say ‘‘Male’’ or ‘‘Female,’’ depending on the system voice you want. The HFL response is, ‘‘Male (Female) prompts have been selected. Would you like an audible notification of an incoming call?’’

Press and release the Talk button. If you say ‘‘Yes’’ after the beep, the HFL response is, ‘‘Would you like the notification to be a ring tone or prompt?’’ If you say ‘‘No’’ after the beep, the HFL returns to its main menu. Saying ‘‘No’’ will result in no ring tone or prompt playback during an incoming call. The audio system will still mute, and a message will be displayed.

Bluetooth HandsFreeLink

5.

6.

Press and release the Talk button. After the beep, say ‘‘Ring tone’’ or ‘‘Prompt.’’ The HFL response is ‘‘A ring tone will be used’’ or ‘‘An incoming call prompt will be used.’’ If you choose ‘‘Ring tone,’’ you will hear a ring tone through the audio speakers to announce an incoming call. If you choose ‘‘Prompt,’’ you will hear this message to announce an incoming call: ‘‘You have an incoming call.’’

The HFL response continues ‘‘A security option is available to lock the HFL system. Each time the vehicle is turned on, a passcode would be required to use this system. Would you like this security option turned on?’’ If you say ‘‘Yes,’’ you can set your passcode. Refer to the setting procedure in the next column.

CONTINUED

223

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３７：４４　３１ＴＥ０６００　０２２９　

Bluetooth HandsFreeLink

Setting Your Passcode The HFL will accept a numeric, four- digit passcode that you can use for security purposes.

Tosetyourpasscode,dothis: Follow the system setup 1. procedure as described previously.

2.

Press and release the Talk button. After the beep, say ‘‘Yes.’’

3.

4.

The HFL response is ‘‘What is the four-digit number you would like to set as your passcode?’’

Press and release the Talk button. After the beep, say the four-digit passcode you want to use. For example, say ‘‘1, 2, 3, 4.’’ The HFL response is ‘‘1, 2, 3, 4. Is this correct?’’

224

5.

Press and release the Talk button. After the beep, say ‘‘Yes.’’ The HFL response is ‘‘Security is on. Each time the vehicle is turned on, the passcode will be required to use the system. The system setup is complete. Returning to the main menu.’’

6.

Press and release the Talk button. If you say ‘‘No.’’ after the beep, the HFL response is ‘‘Security will not be used. The system setup is complete.’’

Toenteryourpasscode,dothis; Once a passcode is set, you can lock the HFL so it only operates after the passcode is entered.

1.

The HFL will prompt you for your passcode each time the ignition switch is turned to the ON (II) position and you press the Talk button. You will only be asked for the passcode once per ignition

2.

3.

cycle. If the passcode is set, its response is ‘‘The system is locked. What is the four-digit passcode?’’

Press and release the Talk button. After the beep, say your four-digit passcode. For example, say ‘‘1, 2, 3, 4.’’

If the passcode is correct, the HFL response is ‘‘Main menu.’’ If the passcode is not correct, the HFL response is ‘‘1, 2, 3, 4 is incorrect. Please try again.’’ Go back to the step 2.

If you forget your passcode and you cannot activate the HFL, consult your dealer to cancel the passcode.

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３７：５５　３１ＴＥ０６００　０２３０　

Pairing Your Phone Your Bluetooth compatible phone with Hands Free Profile must be paired to the HFL before you can make and receive hands-free calls. To confirm that your phone is Bluetooth compatible, visit handsfreelink.honda.com 528-7876. In Canada, call (888) 9- HONDA-9. Your phone retailer should also be able to confirm that your phone is Bluetooth compatible.

, or call (888)

NOTE:

HFL does not allow you to pair your phone if the vehicle is moving. For pairing, your phone must be in its Discovery mode. Up to six phones can be paired to the HFL. The following procedure works for most phones. If you cannot pair your phone to the HFL with this procedure, refer to your phone’s operating manual, visit

, call the

handsfreelink.honda.com Hands Free Link consumer support at (888) 528-7876, or call your phone retailer. In Canada, call (888) 9-HONDA-9. During the pairing process, turn off any previously paired phones before pairing a new phone.

1.

2.

With your phone on and the ignition in the ACCESSORY (I) or ON (II) position, press and release the Talk button. After the beep, say ‘‘Phone setup.’’ The HFL response is ‘‘Phone setup options are status, pair, edit, delete, and list.’’

Press and release the Talk button. After the beep, say ‘‘Pair.’’ The HFL response is ‘‘The pairing process requires operation of your mobile phone. For safety, only perform this function while the vehicle is stopped. State a four- digit code for pairing. Note this

Bluetooth HandsFreeLink

code. It will be requested by the phone.’’

3.

4.

Press and release the Talk button. After the beep, say the four-digit code you want to use. For example, say ‘‘1, 2, 3, 4.’’ The HFL response is, ‘‘1, 2, 3, 4. Is this correct?’’

Press and release the Talk button. After the beep, say ‘‘Yes.’’ The HFL response is ‘‘HFL is now searching for a Bluetooth phone. Make sure the phone you are trying to pair is in discovery mode.’’

Steps 5 and 6 show a

NOTE: common way to get your phone into its Discovery mode. If these steps do not work on your phone, refer to the phone’s operating manual.

CONTINUED

225

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３８：０６　３１ＴＥ０６００　０２３１　

Bluetooth HandsFreeLink

Follow the prompts on your phone to get it into its Discovery mode. The phone will search for the HFL. When it comes up, select HandsFreeLink from the list of options displayed on your phone.

Torenameapairedphone,dothis: 1.

Press and release the Talk button. After the beep, say ‘‘Phone setup.’’ The HFL response is ‘‘Phone setup options are status, pair, edit, delete, and list.’’

Todeleteapairedphone,dothis: 1.

Press and release the Talk button. After the beep, say ‘‘Phone setup.’’ The HFL response is, ‘‘Phone setup options are status, pair, edit, delete, and list.’’

5.

6.

7.

When asked by the phone, enter the four-digit code from step 3 into your phone. The HFL response is ‘‘A new phone has been found. What would you like to name this phone?’’

Press and release the Talk button. After the beep, say the name you want to use. For example, say ‘‘Eric’s phone.’’ The HFL response is ‘‘Eric’s phone has been successfully paired. Returning to the main menu.’’

8.

If you want to pair another phone, repeat steps 1 through 7.

226

2.

3.

Press and release the Talk button. After the beep, say ‘‘Delete.’’ The HFL response is, ‘‘Which phone would you like to delete?’’

Press and release the Talk button. After the beep, say the name of the phone you want to delete. For example say ‘‘Eric’s phone.’’ The HFL response is ‘‘Would you like to delete Eric’s phone?’’

2.

3.

4.

Press and release the Talk button. After the beep, say ‘‘Edit.’’ The HFL response is ‘‘Which phone would you like to edit?’’

Press and release the Talk button. After the beep, say the name of the phone you want to rename. For example, say ‘‘Eric’s phone.’’ The HFL response is ‘‘What is the new name for Eric’s phone?’’

Press and release the Talk button. After the beep, say the new name of the phone. For example, say ‘‘Lisa’s phone.’’ The HFL response is, ‘‘The name has been changed. Returning to the main menu.’’

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３８：１４　３１ＴＥ０６００　０２３２　

4.

5.

Press and release the Talk button. After the beep, say ‘‘Yes.’’ The HFL response is ‘‘Preparing to delete Eric’s phone. Say OK to continue, otherwise, say Go back, or Cancel.’’

Press and release the Talk button. If you say ‘‘OK’’ after the beep, the HFL response is ‘‘The phone has been deleted. Returning to the main menu.’’ If you say ‘‘Go back,’’ or ‘‘Cancel,’’ the phone will not be deleted.

Tolistallpairedphones,dothis: 1.

Press and release the Talk button. After the beep, say ‘‘Phone setup.’’ The HFL response is ‘‘Phone setup options are status, pair, edit, delete, and list.’’

2.

Press and release the Talk button. After the beep, say ‘‘List.’’ The HFL responds by listing the name of each paired phone. When all

phones paired to the system have been read, the HFL response is ‘‘The entire list has been read. Returning to the main menu.’’

Tofindoutthestatusofthephonebeing used,dothis: 1.

Press and release the Talk button. After the beep, say ‘‘Phone setup.’’ The HFL response is, ‘‘Phone setup options are status, pair, edit, delete, and list.’’

2.

Press and release the Talk button. After the beep, say ‘‘Status.’’ An example of the HFL response is, ‘‘Eric’s phone is linked. Battery strength is three bars. Signal strength is five bars, and the phone is roaming. Returning to the main menu.’’

Bluetooth HandsFreeLink

Tochangefromthecurrentlylinked phonetoanotherpairedphone,dothis: 1. Press and release the Talk button. After the beep, say ‘‘Next phone.’’ The HFL response is ‘‘Searching for the next phone.’’ The HFL then disconnects the linked phone and searches for another paired phone. If the HFL finds it, an example of the HFL response is, ‘‘Paul’s phone is linked.’’ If no other phones are found, the first phone remains linked.

227

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３８：２２　３１ＴＥ０６００　０２３３　

2.

Press and release the Talk button. After the beep, say the number you want to call. For example, say ‘‘123 456 7891.’’ The HFL response is ‘‘123 456 7891. Say call, dial, or continue to add numbers.’’

You can also make a call directly from the list shown on the navigation display.

3.

Press and release the Talk button. After the beep, say ‘‘Call’’ or ‘‘Dial.’’ The HFL response is ‘‘Calling’’ or ‘‘Dialing.’’ Once connected, you will hear the person you called through the audio speakers. To change the volume, use the audio system volume knob, or the steering wheel volume controls.

4.

To end the call, press the Back button.

Bluetooth HandsFreeLink

Making a Call You can make calls using any phone number, or by using a name in the HFL phonebook. You can also redial the last number called. During a call, the HFL allows you to talk up to 30
minutes after you remove the key from the ignition switch. Continuing a call without running the engine may discharge and weaken the vehicle’s battery.

Tomakeacallusingaphonenumber, dothis: 1.

With your phone on and the ignition in the ACCESSORY (I) or ON (II) position, press and release the Talk button. After the beep, say ‘‘Call’’ or ‘‘Dial.’’ The HFL response is, ‘‘What name or number would you like to call/ dial?’’

228

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３８：３１　３１ＴＥ０６００　０２３４　

TomakeacallusinganameintheHFL phonebook,dothis: 1.

With your phone on and the ignition in the ACCESSORY (I) or ON (II) position, press and release the Talk button. After the beep, say ‘‘Call’’ or ‘‘Dial.’’ The HFL response is, ‘‘What name or number would you like to call/ dial?’’

2.

3.

Press and release the Talk button. After the beep, say the name you want to call. For example, say ‘‘Eric.’’ The HFL response is ‘‘Would you like to call Eric?’’

Press and release the Talk button. After the beep, say ‘‘Yes.’’ The HFL response is ‘‘Calling’’ or ‘‘Dialing.’’ Once connected, you will hear the person you called through the audio speakers. To change the volume, use the audio system volume knob, or the steering wheel volume controls.

4.

To end the call, press the Back button.

To redial the last number called by the phone, press and release the Talk button. After the beep, say ‘‘Redial.’’ The HFL response is, ‘‘Redialing.’’ Once connected, you will hear the person you called through the audio speakers. To change the volume, use the audio system volume knob, or the steering wheel volume controls.

Bluetooth HandsFreeLink

Sending Numbers or Names During a Call The HFL allows you to send numbers or names during a call. This is useful when you call a menu- driven phone system. You can also program account numbers into the HFL phonebook for easy retrieval during menu-driven calls.

Tosendanumberduringacall,dothis: Press and release the Talk button. 1. After the beep, say ‘‘Send.’’ The HFL response is, ‘‘What name or number would you like to send?’’

2.

Press and release the Talk button. After the beep, say the number you want to send. For example, say ‘‘1, 2, 3.’’ The HFL response is ‘‘1, 2, 3. Say send, or continue to add numbers.’’

To send a pound (

NOTE: ‘‘pound.’’ To send a star (*), say ‘‘star.’’ CONTINUED

), say

＃

229

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３８：４２　３１ＴＥ０６００　０２３５　

Bluetooth HandsFreeLink

3.

Press and release the Talk button. After the beep, say ‘‘Send.’’ The dial tones will be sent, and the call will continue.

Tosendanameduringacall,dothis: 1.

Press and release the Talk button. After the beep, say ‘‘Send.’’ The HFL response is, ‘‘What name or number would you like to send?’’

2.

Press and release the Talk button. After the beep, say the name you want to send. For example, say ‘‘Account number.’’ The HFL response is ‘‘Would you like to send account number?’’

3.

Press and release the Talk button. After the beep, say ‘‘Yes.’’ The dial tones will be sent, and the call will continue.

Receiving a Call If you receive a call when you are not on the phone, the HFL interrupts the audio system (if it is on), and plays the incoming call notification, if activated. To answer the call, press the Talk button and begin speaking. If you don’t want to answer the call, press the Back button.

If your phone has Call Waiting, and you receive a call when you are on the phone, press and release the Talk button to answer it. When you do this, the original call is placed on hold. To return to the original call, press the Talk button again. If you don’t want to answer the new call, disregard it, and continue with your original call. If you want to hang up the original call and answer the new call, press the Back button.

Transferring a Call During a call, you can transfer it from the HFL to your phone, or from your phone to the HFL.

TotransferacallfromtheHFLtoyour phone,dothis: Press and release the Talk button. After the beep, say ‘‘Transfer.’’ The audio switches from the HFL to the phone.

Totransferacallfromyourphonetothe HFL,dothis: Press and release the Talk button. After the beep, say ‘‘Transfer.’’ The audio switches from your phone to the HFL.

230

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３８：５３　３１ＴＥ０６００　０２３６　

Bluetooth HandsFreeLink

Muting a Call During a call, you can mute or unmute your voice to the person you are talking to.

Tomuteyourvoice,dothis: 1.

Press and release the Talk button. After the beep, say ‘‘Mute.’’ The HFL response is, ‘‘Mute is active.’’

Tounmuteyourvoice,dothis: 2.

Press and release the Talk button. After the beep, say ‘‘Mute.’’ The HFL response is, ‘‘Mute is canceled.’’

Setting up the Phonebook The HFL phonebook can store up to 50 names with their associated numbers. These can be any types of numbers. For example, you can store a phone number and use it to make a call, or you can store an account number and use it during a call to a menu-driven phone system.

3.

4.

Toaddaname,dothis: 1.

Press and release the Talk button. After the beep, say ‘‘Phonebook.’’ The HFL response is ‘‘Phonebook options are store, edit, delete, receive contact, and list.’’

2.

Press and release the Talk button. After the beep, say ‘‘Store.’’ The HFL response is, ‘‘What name would you like to store?’’

Press and release the Talk button. After the beep, say the name you would like to store. For example, say ‘‘Eric’’ or say ‘‘account number.’’ The HFL response is ‘‘What is the number for Eric,’’ or ‘‘What is the number for account number?’’

Press and release the Talk button. After the beep, say the number. For example, say ‘‘123 456 7891.’’ The HFL response is ‘‘123 456
7891. Say enter, or continue to add numbers.’’

5.

Press and release the Talk button. After the beep, say ‘‘Enter.’’ The HFL response is ‘‘Eric (or account number) has been stored. Returning to the main menu.’’

CONTINUED

231

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３９：０５　３１ＴＥ０６００　０２３７　

Bluetooth HandsFreeLink

Toeditthenumberofaname,dothis: Press and release the Talk button. 1. After the beep, say ‘‘Phonebook.’’ The HFL response is ‘‘Phonebook options are store, edit, delete, receive contact, and list.’’

2.

3.

4.

Press and release the Talk button. After the beep, say ‘‘Edit.’’ The HFL response is, ‘‘What name would you like to edit?’’

Press and release the Talk button. After the beep, say the name you would like to edit. For example, say ‘‘Eric.’’ The HFL response is ‘‘What is the new number for Eric?’’

Press and release the Talk button. After the beep, say the new number for Eric. For example, say ‘‘987 654 3219.’’ The HFL response is, ‘‘987 654 3219. Say enter, or continue to add numbers.’’

232

5.

Press and release the Talk button. After the beep, say ‘‘Enter.’’ The HFL response is ‘‘The number has been changed. Returning to the main menu.’’

4.

Press and release the Talk button. After the beep, say ‘‘Yes.’’ The HFL response is, ‘‘The name has been deleted. Returning to the main menu.’’

Todeleteaname,dothis: 1.

Press and release the Talk button. After the beep, say ‘‘Phonebook.’’ The HFL response is ‘‘Phonebook options are store, edit, delete, receive contact, and list.’’

2.

3.

Press and release the Talk button. After the beep, say ‘‘Delete.’’ The HFL response is, ‘‘What name would you like to delete?’’

Press and release the Talk button. After the beep, say the name you would like to delete. For example, say ‘‘Eric.’’ The HFL response is ‘‘Would you like to delete Eric?’’

Tolistallnamesinthephonebook,do this: 1.

Press and release the Talk button. After the beep, say ‘‘Phonebook.’’ The HFL response is, ‘‘Phonebook options are store, edit, receive contact, and list.’’

2.

Press and release the Talk button. After the beep, say ‘‘List.’’ The HFL responds by listing the names in the phonebook in the order which they were stored. When the end of the list is reached, the HFL response is, ‘‘The entire list has been read. Returning to the main menu.’’

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３９：１３　３１ＴＥ０６００　０２３８　

Tocallanamefromthephonebooklist, dothis: 1.

Press and release the Talk button. After the beep, say ‘‘Phonebook.’’ The HFL response is ‘‘Phonebook options are store, edit, delete, receive contact, and list.’’

2.

Press and release the Talk button. After the beep, say ‘‘List.’’ The HFL responds by listing the names in the phonebook. When it says the name you want to call, for example, Eric, press the Talk button, and then say ‘‘Call.’’ The HFL response is, ‘‘Would you like to call Eric?’’

3.

Press and release the Talk button. After the beep, say ‘‘Yes.’’ The HFL response is ‘‘Calling.’’ Once connected, you will hear the person you called through the audio speakers. To change the volume, use the audio system volume knob, or the steering wheel volume controls.

Bluetooth HandsFreeLink

Storing a Phone Number Directly from Your Phone You can store the desired number to the HFL phonebook directly from your cellular phone.

NOTE: Your phone may not have this capability. Visit handsfreelink. , or call the Hands Free honda.com Link consumer support at (888) 528-7876. In Canada, call (888) 9- HONDA-9. You can see your phone’s owner’s manual for information.

Tostoreaphonenumberfromyour phone: 1.

With your phone on and the ignition switch in the ACCESSORY (I) or ON (II) position, press and release the Talk button. After the beep, say ‘‘Phonebook.’’ The HFL response is, ‘‘Phonebook options are store, edit, delete, receive contact and list.’’

CONTINUED

233

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３９：２１　３１ＴＥ０６００　０２３９　

4.

5.

Press and release the Talk button. After the beep, say the name you would like to store. For example, say ‘‘Neil at work.’’ The HFL response is, ‘‘Neil at work will be stored. Is this correct?’’

Press and release the Talk button. After the beep, say either ‘‘Yes’’ or ‘‘No.’’ If you say ‘‘Yes,’’ the HFL response is, ‘‘Neil at work has been stored. Would you like HFL to receive another contact?’’ Go to step 6.

If you say ‘‘No,’’ the HFL response is ‘‘Returning to the main menu.’’

6.

7.

If you want to continue to store any other numbers, press and release the Talk button. After the beep, say ‘‘Yes.’’ The HFL response is, ‘‘HFL is now waiting to receive a contact from a Bluetooth device.’’

Select a desired number from the list on your phone, and transmit/ send (individual steps will vary for each type of phone, refer to your phone’s owner’s manual) via Bluetooth. The HFL response is ‘‘One phone number has been received for this contact. What name would you like to store for the mobile number? To discard this number, say ‘Discard.’ ’’

Bluetooth HandsFreeLink

2.

3.

Press and release the Talk button. After the beep, say ‘‘Receive contact.’’ The HFL response is, ‘‘The receive process requires operation of your Bluetooth device. For safety, only perform this function while the vehicle is stopped. HFL is now waiting to receive a contact from a Bluetooth device.’’

Select a desired number from the list on your phone, and transmit/ send (individual steps will vary for each type of phone, refer to your phone’s owner’s manual) via Bluetooth. The HFL response is ‘‘One phone number has been received for this contact. What name would you like to store for the mobile number? To discard this number, say ‘Discard.’ ’’

234

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３９：２９　３１ＴＥ０６００　０２４０　

8.

9.

Press and release the Talk button. After the beep, say the name you would like to store. For example, say ‘‘Susan at work.’’ The HFL response is, ‘‘Susan at work will be stored. Is this correct?’’

Press and release the Talk button. After the beep, say either ‘‘Yes’’ or ‘‘No.’’ The HFL response is ‘‘Susan at work has been stored. Would you like HFL to receive another contact?’’

10.

If you do not want to continue to store any other numbers, press and release the Talk button. After the beep, say ‘‘No.’’ The HFL response is ‘‘Returning to the main menu.’’

Cellular Phonebook Options The cellular phonebook option allows you to store up to 1,000 names and 10,000 phone numbers in the phonebook of Bluetooth HandsFreeLink from your cellular phonebook. The maximum names and numbers to be stored varies on the data size. With the HFL, you can then automatically dial any name or number in the phonebook.

NOTE: Your phone may not have this capability. Visit handsfreelink. , or call the Hands Free honda.com Link consumer support at (888) 528-7876. In Canada, call (888) 9- HONDA-9. You can see your phone’s owner’s manual for information.

Bluetooth HandsFreeLink

To use the cellular phonebook with the HFL, say or select ‘‘Cellular Phonebook’’ from the Information screen. The navigation display will change as shown above.

If any phonebook is not stored and your phone is not linked to the HFL, Cellular Phonebook is grayed out.

CONTINUED

235

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３９：３５　３１ＴＥ０６００　０２４１　

Toimportthecellularphonebook You can import the phonebook of your cellular phone in the HFL. Link your phone to the HFL and select ‘‘Import Cellular Phonebook’’ from the ‘‘Select an option’’ screen. When the message ‘‘The import was successful.’’ is displayed, push in on the Interface Dial to select ‘‘OK.’’

Example

Search Imported Phonebook: This option allows you to search the phone numbers stored in the HFL. When you enter keyword for a person’s name, such as the first name or last name, the system will find the number you want and let you make calls.

Delete Imported Phonebook: This option allows you to delete the stored phonebook from the HFL. When you link your phone to the HFL and select this option, the system will automatically delete the phonebook of the linked phone from the HFL (see page

239

).

Bluetooth HandsFreeLink

PIN Number. This option allows you to add, change, or remove a PIN number for any phonebook that has been imported.

Import Cellular Phonebook: This option allows you to store the phonebook of your cellular phone in the HFL. When you link your phone to the HFL and select this option, the system will start importing and loading the phonebook.

236

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３９：４５　３１ＴＥ０６００　０２４２　

NOTE:

HFL does not allow you to pair your phone if the vehicle is moving. Up to six phones can be paired to the HFL.

Tosearchtheimportedphonebook

PIN ICON

For information on linking to the HFL, see page

225

IMPORTED PHONEBOOK

IMPORTED DATE

You can search the stored number by entering keywords to make calls by using the HFL.

Select ‘‘Search Imported Phonebook’’ from the ‘‘Select an option’’ screen. The display will change as shown above.

Bluetooth HandsFreeLink

Select a phonebook from the displayed list. If the phonebook you select has a PIN icon, you will need the 4-digit PIN number to access the phonebook. The following screen will appear.

Enter the PIN number to access the phonebook. You cannot access a PIN protected phonebook if you do not use the correct PIN number.

CONTINUED

237

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：３９：５５　３１ＴＥ０６００　０２４３　

Bluetooth HandsFreeLink

Select the number (1 6) of the desired person from the list.

−

Up to three category icons are displayed in the right side of the list. These category icons indicate how many numbers are stored for the person. If a name has more than three category icons, ‘‘ ’’ is displayed.

…

The following category icons will appear:

Preference

Home

Mobile

Work

Pager

Fax

Car

Voice

Other

Enter the keyword for a person’s name, such as the first name or last name, using the Interface Dial. If the system does not find an exact match, say or select ‘‘LIST’’ when you finish entering the keyword.

The system will display a list of person’s names, with the closest match to the name you entered at the top of the list.

238

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：４０：０５　３１ＴＥ０６００　０２４４　

Bluetooth HandsFreeLink

TostoreintheBluetooth HandsFreeLink

Todeletetheimportedphonebook

After selecting a person, the system will display a list of the person’s phone numbers.

Select the desired number from the list to make a call.

Say or select ‘‘STORE IN HandsFreeLink’’ from the ‘‘Select a number to call’’ screen. The screen shown above will appear.

Select the desired number from the list to store it in the HFL.

You can delete the stored phonebook from the HFL. Link your phone to the HFL and select ‘‘Delete Imported Phonebook’’ from the ‘‘Select an option’’ screen. The display will change as shown above.

CONTINUED

239

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：４０：１３　３１ＴＥ０６００　０２４５　

Bluetooth HandsFreeLink

Select a phonebook from the displayed list. If the phonebook you select has a PIN icon, you will need the 4-digit PIN number to access the phonebook. The following screen will appear.

After you enter the correct PIN number, or if the phonebook you select is not PIN protected, the following screen appears.

Toadd,change,orremoveaPIN numberfromanyphonebook

Say or select ‘‘Yes’’, and the message ‘‘The imported phonebook has been deleted.’’ will appear. Select ‘‘OK’’ to complete the deletion.

You can add, change or remove a PIN number from any phonebook. Select ‘‘PIN Number’’ from the ‘‘Select an Option’’ screen. The display will change as shown above.

Enter the PIN number to access the phonebook. You cannot access a PIN protected phonebook if you do not use the correct PIN number.

240

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：４０：２１　３１ＴＥ０６００　０２４６　

ToaddaPINnumber

TochangeaPINnumber

Bluetooth HandsFreeLink

1.

Select the phonebook you wish to add the PIN number to. The phonebook you select cannot already have a PIN icon. The display will change as shown above.

2.

Enter the 4-digit PIN number. You will be asked to re-enter the PIN to verify.

1.

Select the phonebook that you wish to change the PIN number for. The display will change as shown above.

CONTINUED

241

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：４０：２９　３１ＴＥ０６００　０２４７　

Bluetooth HandsFreeLink

Clearing the System This operation clears the HFL of your passcode, your paired phones, all names in the HFL phonebook, and all imported phonebooks. Clearing is recommended before you sell your vehicle.

Toclearthesystem,dothis: 1.

Press and release the Talk button. After the beep, say ‘‘System.’’ The HFL response is, ‘‘System options are setup and clear.’’

2.

Press and release the Talk button. After the beep, say ‘‘Clear.’’ The HFL response is, ‘‘This process will clear all paired phones, clear all entries in the phonebook, clear the passcode, and restore the defaults in the system setup. Is this what you would like to do?’’

2.

Enter your current PIN number.

3.

Enter your new 4-digit PIN number. You will be asked to re- enter the PIN to verify.

242

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：４０：３８　３１ＴＥ０６００　０２４８　

3.

4.

5.

Press and release the Talk button. After the beep, say ‘‘Yes.’’ The HFL response is ‘‘Preparing to clear all paired phones, all phonebook entries, the passcode, and restore the defaults in the system setup. Say OK to proceed, otherwise say go back or cancel.’’

Changing Language Canadianmodelsonly TochangefromEnglishtoFrench,do this: 1.

Press and release the Talk button. After the beep, say ‘‘Change language.’’ The HFL response is ‘‘English or French?’’

Press and release the Talk button. After the beep, say ‘‘OK’’ to proceed, or say ‘‘Go back’’ or ‘‘Cancel.’’

2.

If you said ‘‘OK,’’ the HFL response is, ‘‘Please wait while the system is cleared.’’ This may take up to 2 minutes to complete, then the HFL response is, ‘‘The system has been cleared. Returning to the main menu.’’

Press and release the Talk button. After the beep, say ‘‘French.’’ The HFL response is ‘‘Vous avez selectionne Français. Les noms enregistres en mode Anglais ne seront pas accessible en mode Français. Voulez-vous continuer? You have selected French. Name tags that were stored while in English mode will not be accessible in French mode. Would you like to continue? ’’

Bluetooth HandsFreeLink

3.

Press and release the Talk button. After the beep, say ‘‘Oui’’ or ‘‘Yes.’’ If there are no paired phones without French name tags, the HFL response is ‘‘Venillez attendre que le systeme change de langue. Please wait while the language is changed.’’ ‘‘La langue a ete changee. Retour au menu principal.’’

If there are paired phones

NOTE: without French name tags, the following prompts will continue.

If there are paired phones without French name tags, the HFL response is ‘‘Pour que le système identifie les téléphones qui ont été jumelés dans une autre langue, les noms des téléphones doivent être ré- enregistrés.’’

CONTINUED

243

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：４０：４５　３１ＴＥ０６００　０２４９　

Bluetooth HandsFreeLink

4.

＞

The HFL response is, for example, ‘‘Quel est le nom Français pour Paul’s phone ?’’ Press and ＜ release the Talk button. After the beep, say ‘‘Téléphone de Paul.’’ The HFL response is, ‘‘Quel est le nom Français pour phone ?’’ Press and release the Talk button. Say ‘‘Téléphone de Pat.’’ After all paired phones missing a French name tag are re- recorded, the HFL will prompt, ‘‘Retour au menu principal.’’

Pat’s

＜

＞

TochangefromFrenchtoEnglish,do this: 1.

Press and release the Talk button. After the beep, say ‘‘Changer Langue.’’ The HFL response is, ‘‘Anglais ou Français?’’

2.

Press and release the Talk button. After the beep, say ‘‘Anglais.’’ The HFL response is, ‘‘You have selected English. Name tags that were stored while in French mode will not be accessible in English mode. Would you like to continue? Vous avez selectionne Anglais. Les noms enregistres en mode Français ne seront pas accessible en mode Anglais. Voulez-vous contnuez?’’

3.

Press and release the Talk button. After the beep, say ‘‘Yes’’ or ‘‘Oui.’’ If there are no paired phones without English name tags, the HFL response is ‘‘Please wait while the language is changed. Venillez attendre que le systeme change de langue.’’ ‘‘The language has been changed. Returning to the main menu.’’

If there are paired phones

NOTE: without English name tags, the following prompts will continue.

If there are paired phones without English name tags, the HFL response is ‘‘The language has been changed. For the system to identify phones that were paired while in another language, the phone names need to be re- recorded.’’

244

2008 Accord Coupe Table Of ContentsMain Menu０７／０８／０６　１２：４０：４９　３１ＴＥ０６００　０２５０　

Bluetooth HandsFreeLink

4.

?’’ Press

Téléphone de Paul

The HFL says, for example, ‘‘What is the English name for ＜ ＞ and release the Talk button. After the beep, say ‘‘Paul’s phone. ’’ The HFL response is ‘‘What is the English name for Téléphone de Pat ?’’ Press and release the Talk button. After the beep, say ‘‘Pat’s phone.’’ After all paired phones missing an English name tag are re-recorded, the HFL will say ‘‘Returning to the main menu.’’

＜

＞

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly