2004 Honda Accord Coupe Owners Manual

with the switch.

Instruments and Controls

71

Main MenustTable of Contents０３／０７／２６　１９：１３：３１　３１ＳＤＰ６１０　００７５　

Instrument Panel Brightness, Hazard Warning

Instrument Panel Brightness

brightness when you turn the ignition switch to ON (II).

Hazard Warning

If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off in about 30 seconds after closing that door.

If you insert the key but do not turn the ignition switch to ON (II), the illumination turns off in about 10
seconds.

To reduce glare at night, the instru- ment panel illumination dims when or you turn the light switch to

. Turning the Select/Reset

knob fully to the right until you hear a click will cancel the reduced bright- ness.

Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

SELECT/RESET KNOB

The Select/Reset knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness.

The instrument panel will illuminate with reduced brightness when you unlock and open the driver’s door. The brightness will increase slightly when you insert the key in the ignition switch, then go to normal

72

Instruments and Controls

Main MenustTable of Contents０３／０７／２６　１９：１３：３９　３１ＳＤＰ６１０　００７６　

Rear Window Defogger

Manual A/C type shown The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator above/in the button lights to show the defogger is on. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the vehicle.

Auto A/C type shown Make sure the rear window is clear and you have good visibility before starting to drive.

Vehicles with navigation system The defogger and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side to side.

Instruments and Controls

73

Main MenustTable of Contents０３／０７／２６　１９：１３：５０　３１ＳＤＰ６１０　００７７　

3.

Move the steering wheel so it points to your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

4.

Push the lever up to lock the steering wheel in position.

5.

Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.

1.

Insert the key in the ignition switch, and unlock the steering column.

2.

Push the lever under the steering column all the way down.

Steering Wheel Adjustment

15

Seepage forimportantsafety informationabouthowtoproperly positionthesteeringwheel.

Make any steering wheel adjustment before you start driving.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

74

Instruments and Controls

Main MenustTable of Contents０３／０７／２６　１９：１３：５９　３１ＳＤＰ６１０　００７８　

KEY NUMBER TAG

MASTER KEY WITH REMOTE TRANSMITTER

VALET KEY (LIGHT GREY)

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.

These keys contain electronic circuits that are activated by the Immobilizer System. They will not work to start the engine if the circuits are damaged.

Keys and Locks

The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the trunk release handle, rear seat trunk access, and glove box locked when you leave your vehicle and the valet key at a parking facility.

Protect the keys from direct sunlight, high temperature, and high humidity.

Do not drop the keys or set heavy objects on them.

Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.

Instruments and Controls

75

Main MenustTable of Contents０３／０７／２６　１９：１４：０９　３１ＳＤＰ６１０　００７９　

Immobilizer System

The Immobilizer System protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.

The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

If the system repeatedly does not recognize the coding of your key, contact your Honda dealer.

Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undriveable.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

If you have lost your key and cannot start the engine, contact a Honda dealer.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

When you turn the ignition switch to ON (II), the Immobilizer System indicator should come on for a few seconds, then go out. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to LOCK (0), remove the key, reinsert it, and turn the switch to ON (II) again.

76

Instruments and Controls

Main MenustTable of Contents０３／０７／２６　１９：１４：２１　３１ＳＤＰ６１０　００８０　

Ignition Switch

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control.

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).

Remove the key from the ignition switch only when parked.

−

You can insert or

LOCK (0) remove the key only in this position. To turn the key, you must push the key in slightly. If your vehicle has an automatic transmission, the shift lever must also be in park.

−

You can

ACCESSORY (I) operate the audio system and the accessory power sockets in this position.

−

This is the normal key

ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from ACCESSORY (I) to ON (II).

−

Use this position

START (III) only to start the engine. The switch returns to ON (II) when you let go of the key.

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.

On automatic transmission model, the shift lever must be in Park before you can remove the key from the ignition switch.

Instruments and Controls

77

Main MenustTable of Contents０３／０７／２６　１９：１４：３３　３１ＳＤＰ６１０　００８１　

Power Door Locks

MASTER DOOR LOCK SWITCH

LOCK TAB

To lock both doors, push the top of the master door lock switch on either door, or press the lock tab down on the driver’s door, or use the key on the outside lock on the driver’s door.

Pushing the bottom of either master door lock switch will unlock both doors.

78

Instruments and Controls

The lock tab on the passenger’s door lock and unlock only that door. Pulling up on the driver’s door lock tab only unlocks the driver’s door.

To unlock only the driver’s door from the outside, turn the key and release it. If you turn it again, both doors unlock.

You can open or close the windows by using the key in the driver’s door (see page

93

).

To lock the passenger’s door when getting out of the vehicle, push the lock tab down and close the door. To lock the driver’s door, remove the key from the ignition switch and push the lock tab down or push the top of the master switch, then close the door.

LockoutPrevention With the driver’s door open and the key in the ignition, both master door lock switches are disabled. They are not disabled if the driver’s door is closed. Pushing the top of the switch on the open passenger’s door will lock both doors.

Main MenustTable of Contents０３／０７／２６　１９：１４：４４　３１ＳＤＰ６１０　００８２　

Remote Transmitter

UNLOCK BUTTON

PANIC BUTTON

LOCK BUTTON

LED

TRUNK RELEASE BUTTON

−

Press this button once

UNLOCK to unlock the driver’s door. Push it twice to unlock the passenger’s door. Some exterior lights will flash twice each time you push the button. If you do not open either door within 30 seconds, they will automatically relock and the security system sets (except for 4-cylinder LX model). You cannot unlock it if the key is in the ignition switch.

−

Press this button once to

LOCK lock both doors. Some exterior lights will flash once. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors are locked and (if equipped) that the security system has set. You cannot lock it if either door is not fully closed or the key is in the ignition switch.

The ceiling light (if the ceiling light switch is in the center position) and the spotlights (if the switch is in the Door position) will come on when you press the UNLOCK button. If you do not open either door, the lights stay on for about 30 seconds, then fade out. If you relock the doors with the remote transmitter before 30 seconds have elapsed, the lights will go off immediately.

You can also open both power windows from outside the vehicle with the remote transmitter (see page

93

).

TRUNK RELEASE button for about one second to open the trunk. You cannot open it if the key is in the ignition switch.

Press this

−

−

Press this button for

PANIC about two seconds to attract attention: the horn will sound and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter or turn the ignition switch to ON (II).

CONTINUED

Instruments and Controls

79

Main MenustTable of Contents０３／０７／２６　１９：１４：５７　３１ＳＤＰ６１０　００８３　

Remote Transmitter

RemoteTransmitterCare

Avoid dropping or throwing the transmitter.

Protect the transmitter from extreme temperature.

Do not immerse the transmitter in any liquid.

If you lose a transmitter, the replacement needs to be reprogrammed by a Honda dealer.

80

Instruments and Controls

ReplacingtheTransmitterBattery

BATTERY

SCREW

TAB

If it takes several pushes on the button to lock or unlock the doors, replace the battery as soon as possible. Battery type: CR1616

2.

3.

To replace the battery:

1.

Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.

Separate the transmitter by prying its middle seam with your fingernail.

Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.

Main MenustTable of Contents０３／０７／２６　１９：１５：０５　３１ＳＤＰ６１０　００８４　

Remote Transmitter

4.

Remove the old battery from the back of the inner cover, and note the polarity. Make sure the polarity of the new battery is the same ( side facing down), then insert it into the back of the cover.

＋

5.

Install the parts in reverse order.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

Instruments and Controls

81

Main MenustTable of Contents０３／０７／２６　１９：１５：２０　３１ＳＤＰ６１０　００８５　

Trunk

Trunk

Pull

Keep the trunk lid closed at all times while driving to avoid damaging the lid, and to prevent exhaust gas from Carbon getting into the interior. See Monoxide Hazard on page 51

Emergency Trunk Opener

TRUNK RELEASE HANDLE

You can open the trunk in two ways:

Pull the trunk release handle to the left of the driver’s seat.

Press and hold the trunk release button on the remote transmitter.

To close the trunk, press down on the trunk lid.

82

Instruments and Controls

MASTER KEY

To protect items in the trunk when you need to give the key to someone else: 1.

Lock the trunk release handle with the master key.

2.

Give the person the valet key.

As a safety feature, your vehicle has a release lever on the trunk latch so the trunk can be opened from the inside. To open the trunk, push the release lever to the left.

Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page

36

Main MenustTable of Contents０３／０７／２６　１９：１５：３２　３１ＳＤＰ６１０　００８６　

Seats

All V6 models, the 4-cylinder EX-L model, and all Canadian EX models have a power adjustable driver’s seat.

The 4-cylinder EX model has a power seat bottom height adjustment. All other driver’s seat adjustments in this model are manual.

The 4-cylinder LX model has manual driver’s seat adjustments (see next column).

The front passenger’s seat in all models adjusts manually.

−

11 13

Manual Seat Adjustments Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs. Make all seat adjustments before you start driving.

To adjust the seat forward and backward, pull up on the bar under the seat cushion’s front edge. Move the seat to the desired position and release the bar. Try to move the seat to make sure it is locked in position.

To change the seat-back angle, pull up on the lever on the outside of the seat bottom.

Instruments and Controls

83

Main MenustTable of Contents０３／０７／２６　１９：１５：４２　３１ＳＤＰ６１０　００８７　

Seats

Driver’s Seat Manual Height Adjustment

Make sure to pull the lever upward or downward to its full range.

Driver’s Seat Power Height Adjustment

On4-cylinderLXmodel The height of your driver’s seat is adjustable. To raise the seat bottom, repeatedly pull up the lever on the outside of the seat cushion. To lower the seat, push down the lever repeatedly.

Make all seat adjustments before you start driving.

84

Instruments and Controls

On4-cylinderEXmodel The height of your driver’s seat is power adjustable. Pull up on the switch to raise the seat. Push it down to lower the seat.

Make all seat adjustments before you start driving.

Main MenustTable of Contents０３／０７／２６　１９：１５：５４　３１ＳＤＰ６１０　００８８　

Power Seat Adjustments OnallV6models,andthe4-cylinder EX-Lmodel Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.

11 13

−

The controls for the adjustable driver’s power seat are on the outside edge of the seat bottom. You can adjust the power seat with the ignition switch in any position. Make all seat adjustments before you start driving.

Moving the long horizontal switch adjusts the seat bottom in several directions. The seat bottom adjusts in the direction you move the switch. The short vertical switch adjusts the seat-back angle.

Moves the seat forward and backward.

Moves the front of the seat up or down and the rear of the seat up or down.

Seats

Raises or lowers the seat.

Adjusts the seat- back angle forward or backward.

Instruments and Controls

85

Main MenustTable of Contents０３／０７／２６　１９：１６：０６　３１ＳＤＰ６１０　００８９　

Seats

Driver’s Lumbar Support

Armrest

Rear Seat Access Driver’sSide

OnallEXandEX-V6models To change the lumbar support, move the lever on the right side of the seat-back forward or backward. Keep moving the lever forward or backward until you find a suitable position.

To use the console lid as an armrest, slide it to the desired position.

Make sure the passenger’s hands or fingers are away from the armrest before moving it.

RELEASE LEVER

OnallV6modelsand4-cylinderEX-L model To get into the rear seat on the driver’s side, open the door and pull the release lever up on the side of the seat-back. The seat-back will tilt forward to allow easier entry to the rear seat.

86

Instruments and Controls

Main MenustTable of Contents０３／０７／２６　１９：１６：１４　３１ＳＤＰ６１０　００９０　

Passenger’sSide

Seats

After a passenger gets into the back seat, push the seat-back to the upright position and push the whole seat backwards until it latches. Make sure the seat is fully latched before sitting in it.

SEAT-BACK ADJUSTMENT LEVER

RELEASE LEVER

OnLXandEXmodels To get into the rear seat on the driver’s side, open the door and pull up on the seat-back adjustment lever. The seat-back will tilt forward to allow easier entry to the rear seat.

To get into the rear seat on the passenger’s side, push downward on the release lever at the base of the seat-back. The seat-back will tilt forward and the entire seat will move forward to allow easier entry to the rear seat.

Instruments and Controls

87

Main MenustTable of Contents０３／０７／２６　１９：１６：２３　３１ＳＤＰ６１０　００９１　

Seats

Head Restraints Seepage forimportantsafety informationandawarningabouthowto properlypositiontheheadrestraints.

13

Your vehicle has adjustable head restraints on the front seats. They are also on the outside positions of the rear seat.

The head restraints help protect you and your passengers from whiplash and other injuries.

They are most effective when you adjust them so the back of the occupant’s head rests against the center of the restraint.

88

Instruments and Controls

FRONT

REAR

RELEASE BUTTON

The head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways, and push the restraint down.

Main MenustTable of Contents０３／０７／２６　１９：１６：３６　３１ＳＤＰ６１０　００９２　

Folding Rear Seat

MASTER KEY

The left and right halves can be folded separately from inside the vehicle or inside the trunk. To fold down the seat-back from inside the vehicle, insert the master key in the lock on the rear shelf. To fold down the driver’s side, turn the key clockwise, pull down the top of the seat-back, then release the key. To fold down the passenger’s side, turn the key counterclockwise and perform the same procedure.

GUIDE

CENTER SHOULDER BELT When storing cargo, you can move the rear center shoulder belt out of the way by removing the belt from the guide.

Seats

To release the seat-back from inside the trunk, pull the release under the trunk panel. Push the seat-back down, then let go of the release.

Pull

To lock the seat-back upright, push it firmly against the trunk panel. Make sure it is latched in place by pulling on the top of the seat.

Do not put any heavy items on the seat-back when it is folded.

CONTINUED

Instruments and Controls

89

Main MenustTable of Contents０３／０７／２６　１９：１６：４８　３１ＳＤＰ６１０　００９３　

Seats, Seat Heaters

Make sure all rear shoulder belts are positioned in front of the rear seat- back whenever the seat-back is in its upright position.

Seat Heaters

Make sure all items in the trunk, or items extending through the opening into the back seat, are secured. Loose items can fly forward and cause injury if you have to brake hard. See 173

Carrying Cargo

on page

Never drive with the seat-back folded down and the trunk lid open. See on page

Carbon Monoxide Hazard 51

90

Instruments and Controls

SEAT HEATER SWITCH

OnEX-V6modelandEX-Lmodel Both front seats are equipped with seat heaters. Because of the sensors for the side airbag system, there is no heater in the passenger’s seat- back. The ignition switch must be ON (II) to use the heaters.

Push the front of the switch, HI, to rapidly heat up the seat. After the seat reaches a comfortable temperature, select LO by pushing

the back of the switch. This will keep the seat warm.

In HI, the heater turns off when the seat gets warm, and turns back on after the seat’s temperature drops.

In LO, the heater runs continuously. It does not cycle with temperature changes.

Follow these precautions when using the seat heaters:

Use the HI setting only to heat the seats quickly, because it draws large amounts of current from the battery.

If the engine is left idling for an extended period, do not use the seat heaters, even on the LO setting. It can weaken the battery, causing hard starting.

Main MenustTable of Contents０３／０７／２６　１９：１６：５６　３１ＳＤＰ６１０　００９４　

You vehicle’s windows are electrically-powered. Turn the ignition switch to ON (II) to raise or lower either window.

Each door has a switch that controls its window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Close the window by pulling back on the switch and holding it.

MAIN SWITCH

DRIVER’S WINDOW SWITCH The driver’s armrest has a master power window control panel. To open the passenger’s window, push down on the switch and hold it down until the window reaches the desired position. To close the window, pull back on the window switch. Release the switch when the window gets to the position you want.

Power Windows

Closing a power window on someone’s hands or fingers can cause serious injury.

Make sure your passengers are away from the windows before closing them.

CONTINUED

Instruments and Controls

91

Main MenustTable of Contents０３／０７／２６　１９：１７：０８　３１ＳＤＰ６１０　００９５　

Power Windows

−

AUTO To open the driver’s window fully, push the window switch firmly down, then release it. The window automatically goes down all the way. To stop the window from going all the way down, pull back on the window switch briefly.

To close the driver’s window fully, pull back the window switch firmly, then release it. The window automatically goes all the way up. To stop the window from going all the way up, push down on the window switch briefly.

To open or close the driver’s window partially, push down or pull back on the window switch lightly and hold it. The window will stop when you release the switch.

92

Instruments and Controls

When you push the MAIN switch in, the switch is OFF, and the passenger’s window cannot be raised or lowered. To cancel this feature, push on the switch again to get it to pop out. Keep the MAIN switch off when you have children in the vehicle so they do not injure themselves by operating the window unintentionally.

−

If the driver’s

Auto Reverse window runs into any obstacle while it is closing automatically, it will reverse direction and then stop. To close the window, remove the obstacle, then use the window switch again.

Auto reverse stops sensing when the window is almost closed. You should always check that all passengers and objects are away from the window before closing it.

If your vehicle’s battery is disconnected or goes dead, or the driver’s window fuse is removed, the AUTO function will be disabled. The power window system needs to be reset after reconnecting the battery or installing the fuse.

1.

2.

Start the engine. Push down and hold the driver’s window switch until the window is fully open.

Pull and hold the driver’s window switch to close the window completely, then hold the switch for a second or two more.

If the power windows do not operate properly after resetting, have your vehicle checked by a Honda dealer.

Main MenustTable of Contents０３／０７／２６　１９：１７：２３　３１ＳＤＰ６１０　００９６　

The power window system has a key- off delay function. The windows will still operate for up to 10 minutes after you turn off the ignition. Opening either door cancels the delay function. You must turn the ignition switch to ON (II) again before you can raise or lower the windows.

Opening the Windows with the Remote Transmitter You can open both windows from the outside with the remote transmitter.

1.

Press the UNLOCK button once to unlock the driver’s door.

2.

Press the UNLOCK button a second time, and hold it. The passenger’s door unlocks, and both windows start to open. To stop the windows, release the button.

3.

To open the windows further, press the button again.

You cannot close the windows with the remote transmitter.

Power Windows

UNLOCK BUTTON

Open

Close

Opening/Closing the Windows with the Key You can open and close the windows with the key in the driver’s door lock.

To open: 1.

Insert the key in the driver’s door lock.

2.

Turn the key clockwise, then release it.

CONTINUED

Instruments and Controls

93

Main MenustTable of Contents０３／０７／２６　１９：１７：３６　３１ＳＤＰ６１０　００９７　

Power Windows, Moonroof

3.

Turn the key clockwise again, and hold it. Both windows start to open. To stop the windows, release the key.

4.

To open the windows further, turn and hold the key again (within 10 seconds).

NOTE: If the window stops before the desired position, repeat steps 2
and 3.

To close: 1.

Insert the key in the driver’s door lock.

2.

Turn the key counterclockwise, then release it.

3.

Turn the key counterclockwise again, and hold it. Both windows start to close. To stop the windows, release the key.

94

Instruments and Controls

4.

To close the windows further, turn and hold the key again (within 10 seconds).

Moonroof

NOTE: If the window stops before the desired position, repeat steps 2
and 3.

MOONROOF SWITCH

OnallEXandEX-V6models The moonroof has two positions: it can be tilted up in the back for ventilation, or it can be slid back into the roof. Use the switch under the left dashboard vent to operate the moonroof. The ignition switch must be ON (II).

Main MenustTable of Contents０３／０７／２６　１９：１７：４８　３１ＳＤＰ６１０　００９８　

). To open the

To tilt up the back of the moonroof, press and hold the center button ). To close the moonroof, press and hold the upper part of the switch ( moonroof, press and hold the lower part of the switch ( ). Release the switch when the moonroof gets to the desired position. Make sure everyone’s hands are away from the moonroof before opening or closing it.

Opening or closing the moonroof on someone’s hands or fingers can cause serious injury.

Make sure all hands and fingers are clear of the moonroof before opening or closing it.

Moonroof, Mirrors

The moonroof has a key-off delay. You can still open and close the moonroof for up to 10 minutes after you turn off the ignition. The key-off delay cancels as soon as you open either door. You must then turn the ignition to ON (II) for the moonroof to operate.

Mirrors

TAB

If you try to open the moonroof in below-f reezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor.

Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.

The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.

CONTINUED

Instruments and Controls

95

Main MenustTable of Contents０３／０７／２６　１９：１７：５８　３１ＳＤＰ６１０　００９９　

Mirrors

AdjustingthePowerMirrors

ADJUSTMENT KNOB

1.

Turn the ignition switch to ON (II).

2.

Turn the adjustment knob to L (driver’s side) or R (passenger’s side).

96

Instruments and Controls

3.

4.

Push or pull the adjustment knob right, left, up, or down to move the mirror.

When you finish, turn the adjustment knob to the center (off) position. This turns off the adjustment knob to keep your settings.

HEATED MIRROR BUTTON

OnallCanadianmodels The outside mirrors are heated to remove fog and frost. With the ignition switch in the ON (II) position, turn on the heaters by pressing the button. The indicator in the button comes on as a reminder. Press the button again to turn the heaters off.

Main MenustTable of Contents０３／０７／２６　１９：１８：０５　３１ＳＤＰ６１０　０１００　

Parking Brake

Driving the vehicle with the parking brake applied can damage the rear brakes and axles.

PARKING BRAKE LEVER

To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake indicator on the instrument panel should go out when the parking brake is fully released with the ). engine running (see page

59

If you drive at certain speeds without fully releasing the parking brake, the beeper sounds continuously.

Instruments and Controls

97

Main MenustTable of Contents０３／０７／２６　１９：１８：１２　３１ＳＤＰ６１０　０１０１　

Interior Convenience Items

COAT HOOK

CONSOLE COMPARTMENT

BEVERAGE HOLDER

SUN VISOR

BEVERAGE HOLDER

SUNGLASSES HOLDER

VANITY MIRROR

CENTER POCKET

GLOVE BOX

COIN POCKET

ACCESSORY POWER SOCKET

BEVERAGE HOLDER

ACCESSORY POWER SOCKET

98

Instruments and Controls

Main MenustTable of Contents０３／０７／２８　１９：３４：００　３１ＳＤＰ６１０　０１０２　

Glove Box

Beverage Holders

Interior Convenience Items

An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.

Always keep the glove box closed while driving.

GLOVE BOX

Open the glove box by pulling the handle to the left. Close it with a firm push. Lock or unlock the glove box with the master key.

The glove box light comes on when the parking lights are on.

Be careful when you are using the beverage holders. A spilled liquid that is very hot can scald you or your passengers. Liquid can also spill from the door pocket beverage holders when you open or close the doors. Use only resealable containers in the door pockets.

Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior.

Instruments and Controls

99

Main MenustTable of Contents０３／０７／２６　１９：１８：３３　３１ＳＤＰ６１０　０１０３　

Interior Convenience Items

Console Compartment

Center CD Pocket

RIGHT LEVER

LEFT LEVER

Push

CONSOLE COMPARTMENT

To open the console compartment, pull up on the right lever and lift the armrest.

To close, lower the armrest, and push it down until it latches.

You can put small items in the tray located in the console compartment lid. To use the tray, pull up on the left lever and lift up the armrest.

The tray in the console compartment has a coin holder.

OnU.S.vehicleswithoutnavigation systemandallCanadianmodels To open the center CD pocket, push- down on the center of the lid to unlatch it. It will swing open automatically. To close it, push the lid down until it latches. This pocket can store up to 12 CDs.

100

Instruments and Controls

Main MenustTable of Contents０３／０７／２６　１９：１８：４４　３１ＳＤＰ６１０　０１０４　

Interior Convenience Items

Coin Pocket

Sun Visor To use the sun visor, pull it down. When using the sun visor for the side window, remove the support rod from the clip and swing it out.

EXTENSION

SUN VISOR

To open the coin pocket, pull the lid up. To close it, push the lid down until it latches. The compartment cannot be used as an ashtray.

Onvehicleswithoutsidecurtainairbags In this position, the sun visor can be extended by sliding out the extension. Do not use the sun visor extension over the rear view mirror.

Onvehicleswithsidecurtainairbags In this position, the sun visor can be adjusted by moving it on its slider. Do not use the sun visor extension over the rear view mirror.

Make sure you put the sun visor back in place when you are getting into or out of the vehicle.

Instruments and Controls

101

Main MenustTable of Contents０３／０７／２６　１９：１８：５４　３１ＳＤＰ６１０　０１０５　

Interior Convenience Items

Vanity Mirror

Coat Hook

Onvehicleswithsidecurtainairbags

COAT HOOK

Do not put a coat hanger or hard objects on a coat hook. This could result in injuries if your side curtain airbag inflates.

Pull up the vanity mirror cover to use it. The lights beside the mirror come on when you pull up the cover.

To use a coat hook, pull it down. Close it with a firm push.

Make sure the coat hook is closed when you are not using it. This hook is not designed for large or heavy items.

102

Instruments and Controls

Main MenustTable of Contents０３／０７／２６　１９：１９：０７　３１ＳＤＰ６１０　０１０６　

Interior Convenience Items, Interior Lights

Accessory Power Sockets These sockets are intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10
amps).

To use an accessory power socket, the ignition switch must be in ACCESSORY (I) or ON (II).

None of the sockets will power an automotive type cigarette lighter element. When more than one socket is being used, the combined power rating of the accessories should be 120 watts or less (10 amps).

Sunglasses Holder

To open the sunglasses holder, push on the front edge. Make sure the holder is closed while you are driving. Some larger styles of sunglasses may not fit in the holder.

You may also store small items in this holder. Make sure they are small enough to let the holder close and latch, and that they are not heavy enough to cause the holder to pop open while driving.

Ceiling Light

DOOR ACTIVATED

ON

OFF

The ceiling light has a three-position switch; ON, Door Activated, and OFF. In the Door Activated (center) position, the light comes on when you:

Open either door. Unlock the doors with the key or remote transmitter.

CONTINUED

Instruments and Controls

103

Main MenustTable of Contents０３／０７／２６　１９：１９：１６　３１ＳＤＰ６１０　０１０７　

Interior Lights

After both doors are closed tightly, the light dims slightly, then fades out in about 30 seconds.

The ceiling light (with the switch in the center position) comes on when you remove the key from the ignition switch. If you do not open a door, the light stays on, then fades out in about 30 seconds.

If you leave either door open with the key not in the ignition switch, the ceiling light will go off after three minutes.

104

Instruments and Controls

Spotlights

DOOR ACTIVATED

OFF

LX and LX-V6 models

EX and EX-V6 models

Turn on a spotlight by pushing the lens. Push the lens again to turn it off. You can use the spotlights at all times.

OnEXandEX-V6models The spotlights have a two-position switch. In the DOOR position, the lights come on when you open either door. In the OFF position, the lights do not come on.

Main MenustTable of Contents０３／０７／２６　１９：１９：２６　３１ＳＤＰ６１０　０１０８　

The spotlights (with the switch in the DOOR position) also come on when you unlock the door with the key or the remote transmitter, and when you remove the key from the ignition switch.

Courtesy Lights

IGNITION SWITCH LIGHT

Interior Lights

DOOR LIGHT

COURTESY LIGHT

The courtesy light in each door comes on when the door is opened, and goes out when the door is closed.

Your vehicle also has a courtesy light in the ignition switch. This light comes on when you open the driver’s door. It fades out in about 30
seconds after the door is closed.

OnEXandEX-V6models The courtesy light between the spotlights comes on when you turn the parking lights on. To adjust its brightness, turn the Select/Reset knob on the instrument panel.

Instruments and Controls 105

Main MenustTable of Contents０３／０７／２６　１９：１９：２９　３１ＳＤＰ６１０　０１０９　

106

Main MenustTable of Contents０３／０７／２６　１９：１９：３６　３１ＳＤＰ６１０　０１１０　

Comfort and Convenience Features

The heating and air conditioning systems in your Honda provide a comfortable driving environment in all weather conditions.

The standard audio system has many features. This section de- scribes those features and how to use them.

Onallmodelsexceptfor4-cylinderLX model Your Honda has an anti-theft audio system that requires a code number to enable it.

Navigation Systems are available on U.S. models only.

The security system helps to dis- courage vandalism and theft of your Honda.

Vents, Heating, and A/C

............ ..........................

. 108
. 113

Using the A/C To Cool or Heat Automatically

Dual Temperature Control Climate Control Sensors Playing the Radio Radio Reception Playing the XM Satellite

....................... ......... ............. ......................... ...........................

Radio

......................................... ................................. .................................. ................... ........ .... .............................. ............ ................ ......................... ........................... ..............................

Playing a CD CD Changer Protecting Your CDs CD Player Error Messages CD Changer Error Messages Playing a Tape Steering Wheel Controls Radio Theft Protection Setting the Clock Security System Cruise Control HomeLink Universal

. 115
. 117
. 119
. 120
. 126

. 128
. 134
. 137
. 142
. 143
. 144
. 146
. 152
. 153
. 154
. 155
. 156

Transceiver

...............................

. 159

Comfort and Convenience Features 107

Main Menust０３／０７／２６　１９：１９：４４　３１ＳＤＰ６１０　０１１１　

Vents, Heating, and A/C

LX, EX and LX-V6 models

FAN CONTROL DIAL

TEMPERATURE CONTROL DIAL

RECIRCULATION BUTTON

Without Navigation System 4-cylinder EX-L model and EX-V6 model

TEMPERATURE DISPLAY

DRIVER’ S SIDE TEMPERATURE CONTROL DIAL

FAN CONTROL BUTTONS

PASSENGER’ S SIDE TEMPERATURE CONTROL DIAL

AIR CONDITIONING (A/C) BUTTON

MODE BUTTONS

REAR WINDOW DEFOGGER BUTTON

AUTO BUTTON

OFF BUTTON

MODE BUTTON

REAR WINDOW DEFOGGER BUTTON AIR CONDITIONING (A/C) BUTTON

DUAL BUTTON RECIRCULATION BUTTON

DEFROST BUTTON

108

Comfort and Convenience Features

Main MenustTable of Contents０３／０７／２６　１９：１９：５１　３１ＳＤＰ６１０　０１１２　

With Navigation System (U.S. vehicles only) 4-cylinder EX-L model and EX-V6 model

DRIVER’S SIDE TEMPERATURE DISPLAY

PASSENGER’S SIDE TEMPERATURE DISPLAY

TEMPERATURE DISPLAY

Vents, Heating, and A/C

OFF BUTTON

AUTO BUTTON

RECIRCULATION BUTTON

DEFROST BUTTON

AIR CONDITIONING (A/C) ICONS

A/C BUTTON

MODE ICONS

FAN CONTROL ICONS

DRIVER’S SIDE TEMPERATURE CONTROL BUTTONS

PASSENGER’S SIDE TEMPERATURE CONTROL BUTTONS

DUAL BUTTON

REAR WINDOW DEFOGGER BUTTON

Comfort and Convenience Features 109

Main MenustTable of Contents０３／０７／２６　１９：２０：１０　３１ＳＤＰ６１０　０１１３　

Vents, Heating, and A/C

For EX-L (EX model with leather interior) and EX-V6 model, see page for Automatic Climate Control 115
and Manual Operations information.

Fan Control OnallmodelsexceptforEX-Land EX-V6models Turn this dial clockwise to increase fan speed and increase the airflow.

OnEX-LandEX-V6models ForVehicleswithoutNavigationSystem You can manually select the fan speed by pressing the fan control buttons ( ). The fan speed is shown by vertical bars in the display.

or

ForVehicleswithNavigationSystem You can manually select the fan speed. Press the A/C button to view the display, then press any of the fan control icons.

Temperature Control OnallmodelsexceptforEX-Land EX-V6models Turning this dial clockwise increases the temperature of the airflow.

OnEX-LandEX-V6models The driver and passenger can select independent temperature settings.

ForvehicleswithoutNavigationSystem Push the DUAL button. When the indicator in the button is lit, turn the dials to adjust the temperature.

110

Comfort and Convenience Features

ForvehicleswithNavigationSystem Press the DUAL button. The green indicator in the button will come on. The driver and passenger can each select the temperature control buttons ( ) to the desired setting.

▲

▼

or

When the indicator in the DUAL button is off, both sides adjust to the same temperature.

Dual Button OnEX-LandEX-V6models Press the DUAL button to select dual temperature control mode (see page

117

).

Air Conditioning (A/C) Button/ Icons OnallmodelsexceptforEX-Land EX-V6models This button turns the air conditioning on and off. The light above the button is on when the A/C is on.

Main MenustTable of Contents０３／０７／２６　１９：２０：２８　３１ＳＤＰ６１０　０１１４　

OnEX-LandEX-V6models ForVehicleswithoutNavigationSystem Press the A/C button to turn the air conditioning on and off. You will see A/C ON or A/C OFF selected in the display.

ForVehicleswithNavigationSystem Press the A/C button to view the display. Touching ON or OFF in the display turns the air conditioning on and off. You will see A/C ON or A/C OFF in the display.

OnEX-LandEX-V6models When you turn the A/C off, the system cannot regulate the inside temperature if you set the temperature control below the outside temperature.

Recirculation Button When the indicator in/above the button is on, air from the vehicle’s interior issent throughout the system again.When the light is off, air is brought in from the outside of the vehicle(Fresh Air mode).

The outside air intakes for the heating and cooling system are at the base of the windshield. Keep this area clear of leaves and other debris.

The system should be left in Fresh Air mode under almost all conditions. Keeping the system in Recirculation mode, particularly with the A/C off, can cause the windows to fog up.

Switch to Recirculation mode when driving through dusty or smoky conditions, then return to Fresh Air mode.

Vents, Heating, and A/C

Rear Window Defogger Button This button turns the rear window defogger off and on (see page ). 73

Mode Control Use the mode control buttons or icons to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes.

OnEX-LandEX-V6models ForvehicleswithoutNavigationSystem Each time you press the MODE button, the display shows the mode selected.

ForvehicleswithNavigationSystem Press the A/C button to view the display, then touch any of the mode icons on the display.

CONTINUED

Comfort and Convenience Features

111

Main MenustTable of Contents０３／０７／２６　１９：２０：４９　３１ＳＤＰ６１０　０１１５　

Vents, Heating, and A/C

Air flows from the center and corner vents in the dashboard.

Air flow is divided between the vents in the dashboard and the floor vents.

Air flows from the floor

vents.

Air flow is divided between

the floor vents and the defroster vents at the base of the windshield.

Air flows from the defroster vents at the base of the windshield.

or

When you select the system automatically switches to Fresh Air mode and turns on the A/C. In these modes, the A/C stays on with the indicator off.

112

Comfort and Convenience Features

Using the Heater The heater uses engine coolant to warm the air. If the engine is cold, it will be several minutes before you feel warm air coming through the system.

ExceptforEX-LandEX-V6modelswith NavigationSystem 1.

Select When you select automatically switches to Fresh Air mode. Set the fan to the desired speed. Adjust the warmth of the air with the temperature control dial.

, the system

When you select automatically switches to Fresh Air mode.

, the system

MAX A/C Button OnallmodelsexceptforEX-Land EX-V6models

The system automatically turns on the A/C and switches to Recirculation mode. Air flows from the center and side vents in the dashboard.

Ventilation The flow-through ventilation system draws in outside air, circulates it through the interior, then exhausts it through vents near the rear window.

2. 3.

1.

2. 3. 4.

Set the temperature control dial or the button to the lower limit. Make sure the A/C is off. Select Set the fan to the desired speed.

and Fresh Air mode.

Main MenustTable of Contents０３／０７／２６　１９：２１：００　３１ＳＤＰ６１０　０１１６　

Vents, Heating, and A/C

OnEX-LandEX-V6modelswith NavigationSystem

1.

2.

3.

Press the A/C button, the Manual Operation of A/C screen will appear. Select the desired mode and fan speed icons on the display. Adjust the warmth with the temperature buttons ( or

▲ ▼

).

Using the A/C Air conditioning places an extra load on the engine. Watch the engine coolant temperature gauge (see page 67
turn off the A/C until the gauge reads normally.

). If it moves near the red zone,

ExceptforEX-LandEX-V6modelswith NavigationSystem 1.

Turn on the A/C by pressing the button. The light above the button comes on when a fan speed is selected. The display shows A/C ON. Make sure the temperature control dial is set to the lower limit. Select If the outside air is humid, select the Recirculation mode. If the outside air is dry, select the Fresh Air mode. Set the fan to the desired speed.

2.

3. 4.

5.

2. 3.

OnEX-LandEX-V6modelswith NavigationSystem 1.

Press the A/C button, the Manual Operation of A/C screen will appear. Select the ON icon on the display. Select the desired temperature and MODE selections. If the outside air is humid, select the Recirculation mode. If the outside air is dry, select the Fresh Air mode.

you can

Iftheinteriorisverywarm, cool it down more rapidly by partially opening the windows, turning on the A/C, and setting the fan to maximum speed in Fresh Air mode.

CONTINUED

Comfort and Convenience Features

113

Main MenustTable of Contents０３／０７／２６　１９：２１：１４　３１ＳＤＰ６１０　０１１７　

Vents, Heating, and A/C

OnallmodelsexceptforEX-Land EX-V6models To cool with the interior with MAX A/C: 1. 2.

Set the fan to the desired speed. Select the MAX A/C mode. The system automatically turns on the A/C, selects , and switches to the Recirculation mode. Make sure the temperature control dial is all the way to the left.

3.

Dehumidify the Interior Air conditioning, as it cools, removes moisture from the air. When used in combination with the heater, it makes the interior warm and dry.

1. 2. 3. 4.

Switch the fan on. Turn on the air conditioning. Select Adjust the temperature control dial or buttons to your preference.

and Fresh Air mode.

Once the engine is warmed up, this setting is suitable for all driving conditions.

To Defog and Defrost To remove fog from the inside of the windows:

1.

2.

3.

4.

5.

Set the fan to the desired speed or high for faster defrosting. Select

. When you select

, the system automatically

switches to Fresh Air mode and turns on the A/C. The A/C indicator will not come on, if it was off to start with. Adjust the temperature control dial or buttons so the airflow feels warm. Select rear window. To increase airflow to the