1998 Honda Accord Coupe Owners Manual

Download PDF Manual
level gauge attached to the cap. Maintenance LEVEL GAUGE LEVEL GAUGE 4-cylinder models Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather. When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition the blade edges. 6-cylinder models NOTICE Do not use engine antifreeze or a vinegar/water solution in the windshield washer reservoir. Antif reeze can damage your vehicle's paint, while a vinegar/water solution can damage the windshield washer pump. Use only commercially-available windshield washer fluid. Main MenuTable of ContentsstAutomatic Transmission 4-cylinder models Check the fluid level with the engine at normal operating temperature. DIPSTICK 6-cylinder models 1. Park the vehicle on level ground. DIPSTICK Shut off the engine. 2. Remove the dipstick (yellow loop) from the transmission and wipe it with a clean cloth. Transmission Fluid DIPSTICK UPPER MARK LOWER MARK 3. Insert the dipstick all the way into the transmission securely as shown in the illustration. 4. Remove the dipstick and check the fluid level. It should be between the upper and lower marks. CONTINUED Maintenance Main MenuTable of ContentsstTransmission Fluid 5. If the level is below the lower mark, add fluid into the tube to bring it to the upper mark. Always use Honda Premium Formula Automatic Transmission Fluid (ATF). If it is not available, you may use a DEXRON® III automatic transmission fluid as a temporary replacement. However, continued use can affect shift quality. Have the transmission drained and refilled with Honda ATF as soon as it is convenient. 6. Insert the dipstick all the way back into the transmission securely as shown in the illustration. The transmission should be drained and refilled with new fluid according to the time and distance recommen- dations in the maintenance schedule. Maintenance 5-speed Manual Transmission Correct level FILLER BOLT Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Genuine Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole. Reinstall the filler bolt and tighten it securely. If Honda MTF is not available, you may use an API service SG, SH or SJ grade motor oil with a viscosity of SAE 10W-30 or 10W-40 as a temporary replacement. An SG grade is preferred, but an SH or SJ grade may be used if SG is not available. However, motor oil does not contain the proper additives and continued use can cause stiffer shifting. Replace as soon as convenient. The transmission should be drained and refilled with new fluid according to the time and distance recommen- dations in the maintenance schedule. Main MenuTable of ContentsstCheck the fluid level in the reser- voirs monthly. There are up to two reservoirs, depending on model. They are: Brake fluid reservoir (all models) Clutch fluid reservoir (manual transmission only) The brake fluid in the brake system should be replaced according to the time and distance recommendations in the maintenance schedule. Always use Genuine Honda DOT 3 brake fluid. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement. However, the use of any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda DOT 3 brake fluid as soon as possible. Brake fluid marked DOT 5 is not compatible with your vehicle's braking system and can cause extensive damage. Brake and Clutch Fluid Brake System MAX MIN 4-cylinder models The fluid level should be between the MIN and MAX marks on the side of the reservoir. If the level is at or below the MIN mark, your brake system needs attention. Have the brake system inspected for leaks or worn brake pads. CONTINUED Maintenance Main MenuTable of ContentsstBrake and Clutch Fluid MAX Clutch System MAX Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible. 6-cylinder models MIN MIN The fluid should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system. Maintenance Main MenuTable of ContentsstUPPER LEVEL UPPER LEVEL LOWER LEVEL 4-cylinder models Check the level when the engine is cold. Look at the side of the reservoir. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If it is below the LOWER LEVEL, add power steering fluid to the UPPER LEVEL. 6-cylinder models LOWER LEVEL Always use Genuine Honda Power Steering Fluid. If it is not available, you may use another power steering fluid as an emergency replacement. However, continued use can cause increased wear and poor steering in cold weather. Have the power steering system flushed and refilled with Honda PSF as soon as possible. Power Steering A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently and have the system inspected as soon as possible. NOTICE Turning the steering wheel to full left or right lock and holding it there can damage the power steering pump. Maintenance Main MenuTable of ContentsstAir Cleaner Element The air cleaner element should be cleaned or replaced according to the time and distance recommendations in the maintenance schedule. Replacement 4-cylinder Models HOLD-DOWN CLAMPS Cleaning (Severe Conditions) Clean the air cleaner element by blowing compressed air through it in the opposite direction to normal air flow. If you do not have access to compressed air (such as a service station), ask your Honda dealer to do this service. Follow the replacement procedure for removal and reinstallation. Maintenance The air cleaner element is inside the air cleaner housing on the passenger's side of the engine compartment. To replace it: 1. Unsnap the four hold-down clamps and remove the air cleaner housing cover. 2. Remove the old air cleaner element. AIR CLEANER ELEMENT 3. Clean the inside of the air cleaner housing with a damp rag. 4. Place the new air cleaner element in the air cleaner housing. 5. Reinstall the air cleaner housing cover, snap the four hold-down clamps back into place. Main MenuTable of ContentsstAir Cleaner Element Replacement 6-cylinder Models The air cleaner element is inside the air cleaner housing on the driver's side of the engine compartment. To replace it: BOLTS AIR CLEANER ELEMENT 1. Loosen the four bolts and remove the air cleaner housing cover. 4. Place the new air cleaner element in the air cleaner housing. 2. Remove the old air cleaner element. 5. Reinstall the air cleaner housing cover, tighten the four bolts. 3. Clean the inside of the air cleaner housing with a damp rag. Maintenance Main MenuTable of ContentsstSpark Plugs (4-cylinder Models) The spark plugs in your vehicle should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement SPARK PLUG CAP 1. Clean up any dirt and oil around the spark plug caps. 2. Remove the spark plug cap by pulling it straight out. 3. Remove the spark plug with a five-eighths inch (16 mm) spark plug socket. 4. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. Maintenance Main MenuTable of ContentsstSpark Plugs (4-cylinder Models) NOTICE Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head. 6. Install the spark plug cap. 7. Repeat this procedure for the other three spark plugs. Specifications: NGK: DENSO: ZFR5F-11 KJ16CR-L11 Spark Plug Gap: 0.04 in (1.1 mm) Maintenance 5. Torque the spark plug. (If you do not have a torque wrench, tighten the spark plug two-thirds of a turn after it contacts the cylinder head.) Tightening torque: 13 lbf.ft (18 N.m, 1.8 kgf.m) Main MenuTable of ContentsstSpark Plugs (6-cylinder Models) SPARK PLUG CAP The spark plugs in your vehicle are a special platinum-tipped design for longer life. The spark plugs should be replaced according to the time and distance recommendations in the maintenance schedule. Replacement COVER 2. Clean up any dirt and oil around the spark plug caps. 3. Remove the spark plug cap by pulling it straight out. 4. Remove the spark plug with a five-eighths inch (16 mm) spark plug socket. 5. Put the new spark plug into the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it. 1. Remove the cover on the front cylinder bank by pulling on the front edge. Maintenance Main MenuTable of ContentsstSpark Plugs (6-cylinder Models) NOTICE Specifications: NGK: DENSO: PZFR5F-11 PKJ16CR-L11 Spark Plug Gap: 0.04 in (1.1 mm) Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage, the engine. Overtightening can cause damage to the threads in the cylinder head. 1. Install the spark plug cap. 8. Repeat this procedure for the other five spark plugs. 9. Reinstall the cover on the front cylinder bank. 6. Torque the spark plug. (If you do not have a torque wrench, tighten the spark plug two-thirds of a turn after it contacts the cylinder head.) Tightening torque: 13 lbf.ft (18 N.m, 1.8 kgf.m) Maintenance Main MenuTable of ContentsstBattery Check the condition of your vehicle's battery monthly. You should check the color of the test indicator window, and for corrosion on the terminals. TEST INDICATOR WINDOW TEST INDICATOR WINDOW 4-cylinder models Check the battery condition by looking at the test indicator window on the battery. The label on the battery explains the test indicator's colors. 6-cylinder models Check the battery terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent future corrosion. Maintenance Main MenuTable of Contentsst4-cylinder models 6-cylinder models If you need to connect the battery to a charger, disconnect both cables to prevent damage to the vehicle's electrical system. If the terminals are severely cor- roded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals. Always disconnect the negative ( — ) cable first and recon- nect it last. Clean the battery termi- nals with a terminal cleaning tool or wire brush. Reconnect and tighten the cables, then coat the terminals with grease. Battery The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance. CONTINUED Maintenance Main MenuTable of ContentsstBattery On EX and EX-V6 models If your vehicle's battery is discon- nected or goes dead, the audio system will disable itself. The next time you turn on the radio you will see "Code" in the frequency display. Use the Preset buttons to enter the five-digit code (see page 150 ). NOTICE Charging the battery with the cables connected can seriously damage your vehicle's electronic controls. Detach the battery cables before connecting the battery to a charger. Maintenance Main MenuTable of ContentsstCheck the condition of the wiper blades at least every six months. Look for signs of cracking in the rubber, or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used. WIPER ARMS Wiper Blades To replace the blade: 1. Raise the wiper arm off the windshield. Raise the driver's side first, then the passenger's side. LOCK TAB 2. Disconnect the blade assembly from the wiper arm by pushing in the lock tab. Hold it in while you push the blade assembly toward the base of the arm. CONTINUED Maintenance Main MenuTable of ContentsstWiper Blades BLADE BLADE 5. Slide the new wiper blade into the holder until the tabs lock. 6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. 7. Lower the wiper arm down against the windshield. Lower the passenger's side first, then the driver's side. 3. Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder. REINFORCEMENT 4. Examine the new wiper blades. If they have no plastic or metal rein- forcement along the back edge, remove the metal reinforcement strips from the old wiper blade and install them in the slots along the edge of the new blade. Maintenance Main MenuTable of ContentsstYour vehicle's air conditioning is a sealed system. Any major mainte- nance, such as recharging, should be done by a qualified mechanic. You can do a couple of things to make sure the air conditioning works efficiently. Periodically check the engine's radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front surface. These block the air flow and reduce cooling efficiency. Use a light spray from a hose or a soft brush to remove them. NOTICE The condenser and radiator fins bend easily. Only use a low-pressure spray or soft-bristle brush to clean them. AIR CONDITIONING CONDENSER Run the air conditioning at least once a week during the cold weather months. Run it for at least ten minutes while you are driving at a steady speed with the engine at normal operating temperature. This circulates the lubricating oil con- tained in the refrigerant. Air Conditioning System If the air conditioning does not get as cold as before, have your dealer check the system. Recharge the system with Refrigerant HFC-134a (R-134a). (See Specifications on pages 296 and 298.) NOTICE Whenever you have the air conditioning system serviced, make sure the service facility uses a refrigerant recycling system. This system captures the refrigerant for reuse. Releasing refrigerant into the atmosphere can damage the environment. Maintenance Main MenuTable of ContentsstAir Conditioning Filter, Drive Belts Drive Belts ALTERNATOR BELT POWER STEERING BELT 4-cylinder models POWER STEERING BELT Check the condition of the drive belts (two on 4-cylinder models, one on 6-cylinder models). Examine the edges of each belt for cracks or fraying. 6-cylinder models Check the tension of each belt by pushing on it with your thumb midway between the pulleys. Air Conditioning Filter The air conditioning filter removes pollen and dust that is brought in from the outside trough the heating and cooling system/climate control system. This filter should be replaced every 30,000 miles (48,000 km) under normal conditions. It should be replaced every 15,000 miles (24,000 km) if you drive primarily in urban areas that have high concentrations of soot in the air from industry and diesel-powered vehicles. Replace it more often if air flow from the heating and cooling system/climate control system becomes less than usual. Have the air conditioning filter replaced by your Honda dealer. Maintenance Main MenuTable of ContentsstThe belts should have the following "play" or deflection. 4-cylinder models Alternator belt: 0.28 — 0.35 in (7.0 — 9.0 mm) Power steering belt: 0.51 — 0.63 in (13.0 — 16.0 mm) 6-cylinder models Power steering belt: 0.51 — 0.65 in (13.0 — 16.5 mm) If you see signs of wear or looseness, have your dealer adjust or replace the belts. Drive Belts, Timing Belt Timing Belt The timing belt and balancer belt (4- cylinder models only) should normally be replaced at the intervals shown in the maintenance schedule. Replace these belts at 60,000 miles (U.S.) or 100,000 km (Canada) if you regularly drive your vehicle in one or more of these conditions: In very high temperatures (over 110°F, 43°C). In very low temperatures (under — 20°F, — 29°C). Maintenance Main MenuTable of ContentsstTires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how and when to check air pressure, how to inspect your tires for damage and wear, and what to do when your tires need to be replaced. Inflation Keeping the tires properly inflated provides the best combination of handling, tread life and riding comfort. Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated. Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly. Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed. We recommend that you visually check your tires every day. If you think a tire might be low, check it immediately with a tire gauge. Follow all instructions in this owner's manual regarding tire inflation and maintenance. Use a gauge to measure the air pressure at least once a month. Even tires that are in good condition may lose 1 to 2 psi (7 to 15 kPa, 0.07 to 0.15 kgf/cm2) per month. Remember to check the spare tire at the same time you check all the other tires. Check the pressure in the tires when they are cold. This means the vehicle has been parked for at least three hours. If you have to drive the vehicle before checking the tire pressure, the tires can still be considered "cold" if you drive less than 1 mile (1.6 km). If you check the pressure when the tires are hot (the vehicle has been driven several miles), you will see readings 4 to 6 psi (30 to 40 kPa, 0.3 to 0.4 kgf/cm2) higher than the cold reading. This is normal. Do not let air out to match the specified cold pressure. The tire will be underinflated. You should get your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges. Maintenance Main MenuTable of ContentsstRecommended Tire Pressures for Normal Driving The following chart shows the recommended cold tire pressures for most normal driving conditions and speeds. Tire pressures for high speed driving are the same as for normal driving. (LX, EX) (LX-V6) (EX-V6) The compact spare tire pressure is: 60 psi (420 kPa , 4.2 kgf/cm2) These pressures are also given on the tire information label on the driver's doorjamb. Tubeless tires have some ability to self-seal if they are punctured. However, because leakage is often very slow, you should look closely for punctures if a tire starts losing pressure. Tires Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. You should look for: Bumps or bulges in the tread or side of the tire. Replace the tire if you find either of these conditions. Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord. Excessive tread wear. CONTINUED Maintenance Main MenuTable of ContentsstNOTICE (On some models) Improper wheel weights can damage your vehicle's aluminum wheels. Use only Genuine Honda wheel weights for balancing. Tires INDICATOR LOCATION MARKS TREAD WEAR INDICATORS Your vehicle's tires have wear indica- tors molded into the tread. When the tread wears down to that point, you will see a 1/2 inch (12.7 mm) wide band running across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. A tire that is this worn gives very little traction on wet roads. You should replace the tire if you can see the tread wear indicator in three or more places around the tire. Maintenance Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment. The tires were properly balanced by the factory. They may need to be rebalanced at some time before they are worn out. Have your dealer check the tires if you feel a consis- tent vibration while driving. A tire should always be rebalanced if it is removed from the wheel for repair. Make sure the installer balances the wheels when you have new tires installed. This increases riding comfort and tire life. Your vehicle's original tires were dynamic or "spin" balanced at the factory. For best results, have the installer perform a dynamic balance. Main MenuTable of ContentsstTire Rotation Front Front (For Directional Tires and Wheels) (For Non-directional Tires and Wheels) To help increase tire life and distribute wear more evenly, you should have the tires rotated every 7,500 miles (12,000 km). Move the tires to the positions shown in the chart each time they are rotated. When shopping for replacement tires, you may find that some tires are "directional." This means they are designed to rotate only in one direction. If you use directional tires, they should be rotated only front-to- back. Replacing Tires and Wheels The tires that came with your vehicle were selected to match the performance capabilities of the vehicle while providing the best combination of handling, ride comfort, and long life. You should replace them with radial tires of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire's sidewall). Mixing radial and bias-ply tires on your vehicle can reduce its braking ability, traction, and steering accuracy. Tires Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed. Always use the size and type of tires recommended in this owner's manual. It is best to replace all four tires at the same time. If that is not possible or necessary, then replace the two front tires or the two rear tires as a pair. Replacing just one tire can seriously affect your vehicle's han- dling. CONTINUED Maintenance Main MenuTable of ContentsstTires The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the vehicle. Tire size and construction can affect wheel speed and may cause the system to work inconsistently. If you ever need to replace a wheel, make sure the wheel's specifications match those of the original wheel that came on your vehicle. Re- placement wheels are available at your Honda dealer. Maintenance Winter Driving Tires that are marked "M + S" or "All Season" on the sidewall have an all-weather tread design. They should be suitable for most winter driving conditions. Tires without these markings are designed for optimum traction in dry conditions. They may not provide adequate performance in winter driving. For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions. Wheels and Tires Wheel: (LX, EX) 15 x 6 JJ (LX-V6) 15 x 6 1/2 JJ (EX-V6) 16 x 6 1/2 JJ Tire: (LX, EX) (LX-V6) (EX-V6) P195/65R15 89H P205/65R15 92V P205/60R16 91V See Tire Information on page 300 for additional information about tire and wheel size designations. See page 301 for information about DOT Tire Quality Grading. Main MenuTable of ContentsstSnow Tires If you mount snow tires on your Honda, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your vehicle's handling in all weather conditions. Keep in mind the traction provided by snow tires on dry roads may not be as high as your vehicle's original equipment tires. You should drive cautiously even when the roads are clear. Check with the tire dealer for maximum speed recommenda- tions. Tire Chains Mount snow chains on your vehicle when warranted by driving condi- tions or required by local laws. Make sure the chains are the correct size for your tires. Install them only on the front tires. 4-cylinder models If metal chains are used, they must be SAE class "S". Cable-type traction devices can also be used. 6-cylinder models Use only SAE class "S" cable-type traction devices. Tires When installing chains, follow the manufacturer's instructions and mount them as tightly as you can. Drive slowly with chains installed. If you hear the chains contacting the body or chassis, stop and investigate. Make sure the chains are installed tightly, and that they are not contacting the brake lines or suspension. Remove the chains as soon as you begin driving on cleared roads. NOTICE Chains of the wrong size or that arc improperly installed can damage your vehicle 'x brake lines, suspension, body, and wheels. Stop driving if you hear the chains hitting any part of the vehicle. Maintenance Main MenuTable of ContentsstLights Check the operation of your vehicle's exterior lights at least once a month. A burned out bulb can create an unsafe condition by reducing your vehicle's visibility and the ability to signal your intentions to other drivers. HEADLIGHT HIGH BEAM PARKING LIGHT HEADLIGHT LOW BEAM TURN SIGNAL/SIDE MARKER LIGHT Maintenance Main MenuTable of ContentsstTURN SIGNAL/TAILLIGHT HIGH-MOUNT BRAKE LIGHT REAR SIDE MARKER LIGHT STOP/TAILLIGHT BACK-UP LIGHT Lights Check the following: Headlights (low and high beam) Parking lights Taillights Brake lights High-mount brake light Turn signals Back-up lights Hazard light function License plate light Side marker lights Daytime running lights (Canadian models) If you find any bulbs are burned out, replace them as soon as possible. Refer to the chart on pages 297 and 299 to determine what type of replacement bulb is needed. Maintenance Main MenuTable of ContentsstLights Headlight Aiming The headlights were properly aimed when your vehicle was new. You should check their aim if you regularly carry heavy items in the trunk or pull a trailer. Each headlight assembly has horizontal and vertical adjustment indicators. These are set to their standard positions after the headlights are aimed at the factory. To check these settings: 1. Make sure the fuel tank is full. Park the vehicle on level ground. 2. The driver or someone who weighs the same should be sitting in the driver's seat for all checks and adjustments. Load the trunk with the items you normally carry. Maintenance HORIZONTAL ANGLE GAUGE VERTICAL ANGLE GAUGE 5. Check the vertical angle gauge. The bubble should be located underneath the "0" mark on the gauge. If you usually pull a trailer, load it as you would normally and attach it to the vehicle. Push down on the front and rear bumpers several times to make sure the vehicle is sitting normally. 3. Open the hood. 4. Check the horizontal angle gauge. The line on the adjustment screw indicator should line up with the mark on the gauge. Main MenuTable of ContentsstHORIZONTAL ADJUSTMENT VERTICAL ADJUSTMENT 6. If either indicator is not aligned with its mark as described, an adjustment can be made using a Phillips-head screwdriver to realign it with the mark. Please refer to the illustrations. 7. If you cannot get an indicator to align, have your Honda dealer inspect the vehicle for body damage or suspension problems. Lights Replacing a Headlight Bulb Your vehicle has two bulbs on each side, four in total. Make sure you are replacing the bulb that is burned out. Your vehicle uses halogen headlight bulbs. When replacing a bulb, handle it by its plastic case and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth. NOTICE Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter. CONTINUED Maintenance Main MenuTable of ContentsstLights AIR INTAKE DUCT 4-cylinder models 1. Open the hood. 4-cylinder models If you need to change the head- light bulb on the passenger's side, remove the radiator reserve tank and the air intake duct. 6-cylinder models If you need to change the headlight bulb on the driver's side, remove the radiator reserve tank. Maintenance BULB TAB 2. Remove the electrical connector from the bulb by squeezing the connector to unlock the tab, then slide the connector off the bulb. 3. Remove the bulb by turning it approximately one-quarter turn counterclockwise. 4. Insert the new bulb into the hole and turn it one-quarter turn clock- wise to lock it in place. 5. Push the electrical connector back onto the bulb. Make sure it is on all the way. 6. Turn on the headlights to test the new bulb. 7. 4-cylinder models (Passenger's side) Reinstall the radiator reserve tank and the air intake duct. 6-cylinder models (Driver's side) Reinstall the radiator reserve tank. Main MenuTable of ContentsstReplacing Front Turn Signal and Side Marker Light Bulbs HOLDING CLIP Lights 5. Remove the burned out bulb from the socket by pushing it in and turning counterclockwise until it unlocks. 6. Install the new bulb in the socket. Turn it clockwise to lock it in place. 7. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 8. Test the lights to make sure the new bulb is working. 1. If you are changing the bulb on the driver's side, start the engine, turn the steering wheel all the way to the right, and turn off the engine. If you are changing the bulb on the passenger's side, turn the steering wheel to the left. 2. Use a flat-tipped screwdriver to remove the holding clip from the inner fender. 9. Put the inner fender in place. Install the holding clip. Lock it in place by pushing on the center. 3. Pull the inner fender away from the fender and bumper. 4. Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise. Maintenance Main MenuTable of ContentsstLights Replacing a Parking Light Bulb POWER STEERING FLUID TANK HOLDER 1. Open the hood. The front parking light is next to the headlight bulb. the driver's side, remove the radiator reserve tank. 2. Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise. 4-cylinder models If you need to change a bulb on the passenger's side, remove the radiator reserve tank. On the driver's side, remove the power steering fluid tank. 6-cylinder models If you need to change a bulb on Maintenance 3. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 4. Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place. 5. Turn on the parking lights to make sure the new bulb works. 6. 4-cylinder models (Passenger's side) Reinstall the radiator reserve tank. (Driver's side) Reinstall the power steering fluid tank. 6-cylinder models (Driver's side) Reinstall the radiator reserve tank. Main MenuTable of ContentsstReplacing Rear Bulbs (in Fenders) FASTENER 1. Open the trunk. 2. Remove the fastener on the side of the trunk lining by turning it counterclockwise. Pull the lining back. Lights 4. Remove the socket by turning it one-quarter turn counterclockwise. 5. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 6. Reinstall the socket into the light assembly by turning it clockwise until it locks. 7. Test the lights to make sure the new bulb is working. 3. Determine which of the two bulbs is burned out: stop/taillight or turn signal/taillight. 8. Reinstall the trunk lining. Make sure it is installed under the edge of the trunk seal. CONTINUED Maintenance Main MenuTable of ContentsstLights 9. Reinstall the rear panel. Put each fastener in the hole on the rear panel and push on the center until it locks (the center is flush with the head). 10.Put the fastener in the hole of the side of the trunk lining and push on the center until it locks (the center is flush with the head). Replacing Rear Bulbs (in Trunk Lid) SCREW 1. Open the trunk. 2. Remove the screw securing the plastic cover. Then remove the plastic cover. 3. Determine which of the two bulbs is burned out: stop/taillight or back-up light. Maintenance Main MenuTable of Contentsst4. Remove the socket by turning it one-quarter turn counterclockwise. Replacing a Rear Side Marker Light Bulb Lights 5. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 6. Reinstall the socket into the light assembly. 7. Test the lights to make sure the new bulb is working. 8. Reinstall the plastic cover and secure it with the screw. SCREW 1. Use a Phillips-head screwdriver to loosen the side marker assembly mounting screw. 3. Remove the socket from the light assembly by turning it counter- clockwise. 2. Remove the assembly from the fender by pulling out the back edge and sliding the assembly backwards. 4. Remove the bulb from the socket by pulling it straight out. Install the new bulb. Turn on the headlights to test the bulb. CONTINUED Maintenance Main MenuTable of ContentsstLights 5. Insert the socket in the assembly. Turn it clockwise to lock it in place. Replacing a High-mount Brake Light Bulb 6. Reinstall the side marker assem- bly in the bumper. Tighten the mounting screw securely. 3. Install the new bulb and reinstall the socket. Make sure the new bulb is working. 1. Open the trunk and remove the socket from the light assembly by turning it one-quarter turn counter- clockwise. 2. Remove the burned-out bulb by pulling it straight out of the socket. Maintenance Main MenuTable of ContentsstReplacing a Rear License Bulb 1. Use a Phillips-head screwdriver to loosen the two screws holding the license plate light bracket. Slide the bracket out from the bumper. 2. Remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 3. Pull the bulb straight out of its socket. Push the new bulb in until it bottoms in the socket. Lights 4. Turn on the parking lights and check that the new bulb is working. 5. Put the license light bracket in place. Tighten the two screws securely. Maintenance Main MenuTable of ContentsstLights Replacing Bulbs in the Interior Courtesy Lights The ceiling light, door light and vanity mirror light come apart the same way. They do not all use the same bulb. CEILING LIGHT DOOR LIGHT 1. Remove the lens by carefully prying on the edge of the lens with a fingernail file or a small flat-tip screwdriver. Do not pry on the edge of the housing around the lens. Door light: Pry on the top middle of the lens. Ceiling light: pry on the front edge of the lens near both sides. Maintenance Main MenuTable of ContentsstSPOTLIGHT VANITY MIRROR LIGHT LENS Spotlight: pry on the front edge in front of both spotlights. 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. Snap the lens back in place. Lights Replacing the Trunk Light Bulb TRUNK LIGHT 1. Open the trunk. Pull down the trunk light cover. 2. Remove the bulb by pulling it straight out of its metal tabs. 3. Push the new bulb into the metal tabs. 4. Push the cover back in place. Maintenance Main MenuTable of ContentsstStoring Your Vehicle If you need to park your vehicle for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors. Fill the fuel tank. Change the engine oil and filter (see page 208). Wash and dry the exterior completely. Clean the interior. Make sure the carpeting, floor mats, etc. are completely dry. Leave the parking brake off. Put the transmission in Reverse (5- speed manual) or Park (automatic). Maintenance Block the rear wheels. If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground. Leave one window open slightly (if the vehicle is being stored indoors). Disconnect the battery. Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield. To minimize sticking, apply a silicone spray lubricant to all door and trunk seals. Also, apply a vehicle body wax to the painted surfaces that mate with the door and trunk seals. Cover the vehicle with a "breathable" vehicle cover, one made from a porous material such as cotton. Nonporous materials, such as plastic sheeting, trap moisture, which can damage the paint. If possible, run the engine for a while periodically (preferably once a month). If you store your vehicle for 12 months or longer, have your Honda dealer perform the inspections called for in the 24 months/30,000 miles (48,000 km) maintenance schedule (Normal Conditions) as soon as you take it out of storage (see page 196 ). The replacements called for in the maintenance schedule are not needed unless the vehicle has actually reached that time or mileage. Main MenuTable of ContentsstRegular cleaning and polishing of your Honda helps to keep it "new" looking. This section gives you hints on how to clean your vehicle and preserve its appearance: the paint, brightwork, wheels and interior. Also included are several things you can do to help prevent corrosion. Appearance Care Exterior Care.................................. 260 Washing..................................... 260 Waxing....................................... 261 Aluminum Wheels..................... 261 Paint Touch-up........................... 261 Interior Care................................... 262 Carpeting.................................... 262 Fabric.......................................... 262 Vinyl............................................ 262 Leather....................................... 262 Seat Belts.................................... 263 Windows..................................... 263 Air Fresheners........................... 263 Corrosion Protection..................... 264 Body Repairs.................................. 265 Appearance Care Main MenustExterior Care Washing Frequent washing helps preserve your vehicle's beauty. Dirt and grit can scratch the paint, while tree sap and bird droppings can permanently ruin the finish. Wash your vehicle in a shady area, not in direct sunlight. If the vehicle is parked in the sun, move it into the shade and let the exterior cool down before you start. Only use the solvents and cleaners recommended in this Owner's Manual. NOTICE Chemical solvents and strong cleaners can damage the paint, metal, and plastic on your vehicle. Appearance Care When you have washed and rinsed the whole exterior, dry it with a chamois or soft towel. Letting it air-dry will cause dulling and water spots. As you dry the vehicle, inspect it for chips and scratches that could allow corrosion to start. Repair them with touch-up paint (see page 261). Rinse the vehicle thoroughly with cool water to remove loose dirt. Fill a bucket with cool water. Mix in a mild detergent, such as dishwashing liquid or a product made especially for vehicle washing. Wash the vehicle using the water and detergent solution and a soft- bristle brush, sponge, or soft cloth. Start at the top and work your way down. Rinse frequently. Check the body for road tar, tree sap, etc. Remove these stains with tar remover or turpentine. Rinse it off immediately so it does not harm the finish. Remember to re- wax these areas, even if the rest of the vehicle does not need waxing. Main MenuTable of ContentsstWaxing Always wash and dry the whole vehicle before waxing it. You should wax your vehicle, including the metal trim, whenever water sits on the surface in large patches. It should form into beads or droplets after waxing. You should use a quality liquid or paste wax. Apply it according to the instructions on the container. In general, there are two types of products: Waxes — A wax coats the finish and protects it from damage by exposure to sunlight, air pollution, etc. You should use a wax on your Honda when it is new. Polishes — Polishes and cleaner/ waxes can restore the shine to paint that has oxidized and lost some of its shine. They normally contain mild abrasives and solvents that remove the top layer of the finish. You should use a polish on your Honda if the finish does not have its original shine after using a wax. Cleaning tar, insects, etc. with removers also takes off the wax. Remember to re-wax those areas, even if the rest of the vehicle does not need waxing. Aluminum Wheels On some models Clean your Honda's aluminum alloy wheels as you do the rest of the exterior. Wash them with the same solution, and rinse them thoroughly. The wheels have a protective clear- coat that keeps the aluminum from corroding and tarnishing. Using harsh chemicals, including some commercial wheel cleaners, or stiff brushes can damage this clear-coat. Only use a mild detergent and soft brush or sponge to clean the wheels. Exterior Care Paint Touch-up Your dealer has touch-up paint to match your vehicle's color. The color code is printed on a sticker on the driver's doorjamb. Take this code to your dealer so you are sure to get the correct color. Inspect your vehicle frequently for chips or scratches in the paint. Repair them right away to prevent corrosion of the metal underneath. Use the touch-up paint only on small chips and scratches. More extensive paint damage should be repaired by a professional. Appearance Care Main MenuTable of ContentsstInterior Care Carpeting Vacuum the carpeting frequently to remove dirt. Ground-in dirt will make the carpet wear out faster. Periodically shampoo the carpet to keep it looking new. Use one of the foam-type carpet cleaners on the market. Follow the instructions that come with the cleaner, applying it with a sponge or soft brush. Keep the carpeting as dry as possible by not adding water to the foam. Appearance Care Leather On EX and EX-V6 models Vacuum dirt and dust from the leather frequently. Pay particular attention to the pleats and seams. Clean the leather with a soft cloth dampened with clear water, then buff it with a clean, dry cloth. If further cleaning is needed, use a soap specifically for leather, such as saddle soap. Apply this soap with a damp, soft cloth. Wipe down and buff as described above. Fabric Vacuum dirt and dust out of the material frequently. For general cleaning, use a solution of mild soap and lukewarm water, letting it air dry. To clean off stubborn spots, use a commercially-available fabric cleaner. Test it on a hidden area of the fabric first, to make sure it does not bleach or stain the fabric. Follow the instructions that come with the cleaner. Vinyl Remove dirt and dust with a vacuum cleaner. Wipe the vinyl with a soft cloth dampened in a solution of mild soap and water. Use the same solution with a soft-bristle brush on more difficult spots. You can also use commercially-available spray or foam-type vinyl cleaners. Main MenuTable of ContentsstSeat Belts LOOP If your seat belts get dirty, you can use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. They can weaken the belt material. Let the belts air- dry before you use the vehicle. Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol. Windows Clean the windows, inside and out, with a commercially-available glass cleaner. You can also use a mixture of one part white vinegar to ten parts water. This will remove the haze that builds up on the inside of the windows. Use a soft cloth or paper towels to clean all glass and clear plastic surfaces. Interior Care NOTICE The rear window defogger and antenna wires are bonded to the inside of the glass. Wiping vigorously up-and- down can dislodge and break these wires. When cleaning the rear window, use gentle pressure and wipe side-to- side. Air Fresheners If you want to use an air freshener/ deodorizer in the interior of your vehicle, it is best to use a solid type. Some liquid air fresheners contain chemicals that may cause parts of the interior trim and fabric to crack or discolor. If you use a liquid air freshener, make sure you fasten it securely so it does not spill as you drive. Appearance Care Main MenuTable of ContentsstCorrosion Protection Two factors normally contribute to causing corrosion in your vehicle: 1. Moisture trapped in body cavities. Dirt and road salt that collects in hollows on the underside of the vehicle stays damp, promoting corrosion in that area. Many corrosion-preventive measures are built into your Honda. You can help keep your vehicle from corroding by performing some simple periodic maintenance: Repair chips and scratches in the paint as soon as you discover them. 2. Removal of paint and protective coatings from the exterior and underside of the vehicle. Inspect and clean out the drain holes in the bottom of the doors and body. Check the floor coverings for dampness. Carpeting and floor mats may remain damp for a long time, especially in winter. This dampness can eventually cause the floor panels to corrode. Use a high-pressure spray to clean the underside of your vehicle. This is especially important in areas that use road salt in winter. It is also a good idea in humid climates and areas subject to salt air. Vehicles equipped with ABS have a sensor and wiring at each wheel. Be careful not to damage them. Have the corrosion-preventive coatings on the underside of your vehicle inspected and repaired periodically. Appearance Care Main MenuTable of ContentsstBody repairs can affect your vehicle's resistance to corrosion. If your vehicle needs repairs after a collision, pay close attention to the parts used in the repair and the quality of the work. Make sure the repair facility uses Genuine Honda replacement body parts. Some companies make sheet metal pieces that seem to duplicate the original Honda body parts, but are actually inferior in fit, finish, and corrosion resistance. Once installed, they do not give the same high- quality appearance. When reporting your collision to the insurance company, tell them you want Genuine Honda parts used in the repair. Although most insurers recognize the quality of original parts, some may try to specify that the repairs be done with other available parts. You should investi- gate this before any repairs are begun. Take your vehicle to your authorized Honda dealer for inspection after the repairs are completed. He can make sure that quality materials were used, and that corrosion-preventive coatings were applied to all repaired and replaced parts. Body Repairs Appearance Care Main MenuTable of ContentsstTaking Care of the Unexpected This section covers the more- common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed. Compact Spare Tire....................... 268 Changing a Flat Tire..................... 269 If Your Engine Won't Start........... 274 Nothing Happens or the Starter Motor Operates Very Slowly............................. 275 The Starter Operates Normally................................ 276 Jump Starting................................. 276 If Your Engine Overheats............. 279 Low Oil Pressure Indicator.......... 281 Charging System Indicator........... 282 Malfunction Indicator Lamp ........ 283 Brake System Indicator................ 284 Closing the Moonroof................... 285 Fuses............................................... 286 Checking and Replacing........... 287 Towing............................................ 291 Taking Care of the Unexpected Main MenustCompact Spare Tire Your vehicle has a compact spare tire that takes up less space. Use this spare tire as a temporary replace- ment only. Get your regular tire repaired or replaced and put back on your vehicle as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm2) Taking Care of the Unexpected Follow these precautions whenever you are using the compact spare tire: INDICATOR LOCATION MARK Do not exceed 50 mph (80 km/h) under any circumstances. This tire gives a harsher ride and less traction on some road sur- faces than the regular tire. Use greater caution while driving on this tire. Do not mount snow chains on the compact spare. The wheel of the compact spare tire is designed especially to fit your vehicle. Do not use your spare tire on another vehicle unless it is the same make and model. TREAD WEAR INDICATOR BAR The compact spare tire has a shorter tread life than a regular tire. Replace it when you can see the tread wear indicator bars. The replacement should be the same size and design tire, mounted on the same wheel. The compact spare tire is not designed to be mounted on a regular wheel, and the compact wheel is not designed for mounting a regular tire. Main MenuTable of ContentsstIf you have a flat tire while driving, stop in a safe place to change it. Stopping in traffic or on the shoulder of a busy road is dangerous. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes. The vehicle can easily roll off the jack, seriously injuring anyone underneath. Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack. 1. Park the vehicle on firm, level ground away from traffic. Turn on the hazard warning lights and turn the ignition switch to LOCK (0). Changing a Flat Tire TRUNK FLOOR TOOL KIT SPARE TIRE JACK COVER 2. Put the transmission in Park (automatic) or Reverse (manual). Apply the parking brake. Have all of the passengers get out of the vehicle while you change the tire. 3. Open the trunk. Raise the trunk floor by lifting up on the back edge. 4. The tools are in the tool box on the right side of the trunk. Take the tools out of the tool box. 5. Unscrew the wing bolt and take the spare tire out of its well. 6. The jack is behind a cover in the right fender. Remove the cover by turning the handle counterclock- wise, then pulling on the cover. CONTINUED Taking Care of the Unexpected Main MenuTable of ContentsstChanging a Flat Tire JACK WHEEL NUTS 7. Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. 8. Loosen the four wheel nuts (4- cylinder) or five (V-6) 1/2 turn with the wheel wrench. WHEEL WRENCH JACKING POINT 9. Find the jacking point nearest the wheel you are removing. Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting in the jack notch. Taking Care of the Unexpected Main MenuTable of ContentsstEXTENSION WHEEL COVER Changing a Flat Tire WHEEL WRENCH 10. Use the extension and wheel wrench as shown to raise the vehicle until the flat tire is off the ground. WHEEL NUTS 11. Remove the wheel nuts and flat tire. Temporarily place the flat tire on the ground with the outside surface of the wheel facing up. You could scratch the wheel if you put it face down. On LX and LX-V6 models Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool. The wheel cover cannot be removed without first removing the wheel nuts. CONTINUED Taking Care of the Unexpected Main MenuTable of ContentsstChanging a Flat Tire BRAKE HUB 12. Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully, it may be hot from driving. 13. Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully. 14. Lower the vehicle to the ground and remove the jack. Taking Care of the Unexpected Main MenuTable of ContentsstChanging a Flat Tire 4-cylinder models 6-cylinder models 15. Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. Tighten the wheel nuts to:

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

1998 Honda Accord Coupe Owners Manual