1993 Honda Accord Coupe Owners Manual

After washing your car or after heavy rain, check for leaks. Dry any wet areas of your car's interior. Have teaks repaired as soon as possible.

inside rear wheel housing,

under rear bumper.

above subframe,

rear suspension,

CAUTION: Cars with ABS have a speed detection device mounted at each wheel. Care should be taken when clearing mud, snow, etc., from the wheels not to damage the detectors.

SPEED DETECTOR

Body Repair

Replacement Body and Fender Parts If your vehicle incurs body damage and requires replacement parts, we encourage you to use only Genuine Honda sheet metal body and fender parts. Many insurance companies are specifying imitation sheet metal parts for collision repairs in an effort to reduce claim costs; however, if imitation parts are used the following conditions may apply:

There is no assurance that imitation parts will equal the fit and finish of Genuine Honda sheet metal parts; and in our experience they often do not. There is no assurance that imitation parts will resist corrosion as well as Genuine Honda sheet metal parts. Imitation sheet metal parts are not covered by the Honda Limited Warranty.

To ensure your continued satisfaction with your Honda vehicle in the event of an accident, contact your insurance adjuster and insist on Genuine Honda parts in the repair of your vehicle.

Spare Tire

COMPACT Spare Tire Your car is supplied with a COMPACT spare tire and wheel for temporary use only in the event of a flat tire. Use the COMPACT spare only when you have to, and only to go as far as the next garage or dealer to have the regular tire repaired and reinstalled.

Because you will rarely use the COMPACT spare, be sure to regularly check its condition and air pressure (415 kPa, 60 psi), so it will be ready when you need it. This type of tire holds less air at higher pressure than a regular tire, so it will inflate (or deflate if there is a teak) more rapidly; check its pressure often and add air gradually if it needs any.

The COMPACT spare tire has a different tire size, air pressure re- quirement, tread life and maxi- mum speed rating than the four regular tires on your car. Disre- garding these warnings may re- sult in tire failure, toss of vehicle control and possible injury to vehicle occupants. Do not exceed 50 mph (80 km/h) under any circumstances whan using the COMPACT spare. Do not mount snow chains on the COMPACT spare. They will not fit properly and will damage the tire and possibly your car. If you must use the COMPACT spare when driving on roads covered with snow or ice, use it as one of the rear tires and mount chains only on the front two regular tires.

INDICATOR LOCATION MARK

TREAD WEAR INDICATOR

The COMPACT spare tire has a much shorter tread life than regu- lar tires. Replace the tire as soon as tread wear indicators appear as solid bands across the tread. Replace with a tire of exactly the same size and construction. The COMPACT spare tire and wheel set was designed espe- cially for your car; do not use it on any other vehicle; do not in- stall any other tire on this wheel which is not identical to the original in size and construction, and do not use the COMPACT spare tire on any other wheel. Because the COMPACT spare is smaller in size and higher in air pressure than a regular tire, it will ride more harshly with less ground clearance and may have less traction on some road surfaces. Drive cautiously.

Changing a Flat Tire

Do not attempt to change a tire unless the car is on firm, level ground and weft out of the flow of traffic.

Park the car on a firm, level surface, apply the parking brake, turn on the hazard warning switch, turn the ignition off and put the transmission in gear (Park for automatic transmission). 1. Remove the cover. 2. Remove the jack.

NOTE: Turn the connector on the end of the jack counterclockwise to loosen it from its mount.

COVER

JACK

TOOL BAG

COMPACT SPARE

3. Remove the lug wrench/jack handle and jack handle extension

from the tool bag.

4. Remove the spare tire. 5. Place blocks in front and back of the wheel diagonally opposite

the tire you are changing.

6. Use the lug wrench to loosen the wheel lug nuts counterclock-

wise one-half turn. (US: EX/SE, Canada: EX-R/SE) First remove the center cap from the wheel by prying it out with a common flat screwdriver (not included in the tool kit).

CAUTION: Hold the center cap with your hand then pry ft off using a rag to protect the cap and the wheel.

CENTER CAP

SCREWDRIVER

Follow tire changing preparations and procedures carefully to reduce the possibility of injury. The jack is designed for changing tires only. STAND CLEAR, DO NOT get under the car and DO NOT run the engine when the car is supported only by the jack.

7. Place the jack under the car as shown and raise the car by turning

the handle clockwise until the tire is slightly off the ground.

To reduce the possibility of injury, be sure to use the jack provided with the car and the correct jacking points; never use any other part of the car for jack support.

JACK HANDLE EXTENSION

8. Remove the lug nuts and wheel.

LUG WRENCH/JACK HANDLE

(US: DX/LX, Canada: EX) Remove the lug nuts, wheel cover, and wheel.

WHEEL COVER

LUG NUT

(cont'd)

VALVE

Changing a Flat Tire (cont'd)

9. Everytime you install the wheel on the brake hub, use a clean rag to wipe any dirt off the mounting surface of the hub and the wheel. This will assure a tight, even contact between the wheel and hub.

10. Install the spare, and lug nuts hand tight. 11. Lower the car, remove the jack, then tighten the lug nuts

securely in an " X" pattern as shown.

12. Tighten the lug nuts to the recommended torque:

110 N.m (11 kg-m,80 Ib-ft) If a torque wrench was not used, ask an authorized Honda dealer to verify the torque as soon as possible.

TIGHTENING TORQUE 110 N.m (11 kg-m, 80 Ib-ft)

13. Repair or replace the damaged tire as soon as you can, reinstall it

in its original position, then put the spare back in the car.

CAUTION: Always stow the jack, tools, and tire securely to prevent them from becoming dangerous projectiles in an accident,

14.Secure the tire and the spacer as shown in the illustration.

SPACER

COMPACT SPARE TIRE

NORMAL TIRE

Jump Starting

To start a car with a dead battery, use another battery of the same voltage, and the proper jumper cables.

Procedures other than those below could cause injury or damage from battery acid spray, explosion or charging system overload. Never connect the jumper cable directly to the negative post of the "dead" battery. Never allow the two cars to touch each other. Never allow the jumper cable clamps to touch each other. Never lean over the battery when making connections. Never attempt to jump start a vehicle with a frozen battery. The battery could rupture and explode. If you suspect a frozen battery, remove the vent caps and check the fluid. If there seems to be no fluid, or if you see ice, do not attempt a jump start until the fluid thaws.

CAUTION: If jumper cables are connected backwards, the car's main fuse may blow.

1 .Turn off all lights, heater and other electrical loads, set the parking

brake, and shift the transmission to Neutral or Park.

2. Use one cable to connect the positive terminal of the booster

battery to the positive terminal of the "dead" battery.

DEAD BATTERY

Positive to positive

Do not attach cable here.

Negative to the engine, net to the battery

BOOSTER BATTERY

3. Use the other cable to connect the negative terminal of the

booster battery to the engine at the ground cable as shown.

4.To remove the cables, reverse the above procedures exactly.

DO NOT push or tow a car to start it. The forward surge when the engine starts could cause a collision. Also, under some conditions, the three way catalytic converter could be damaged. A car equipped with an automatic transmission cannot be started by pushing or towing.

NOTE: (US: EX/SE, Canada: EX-R/SE) After jump-starting the car, there is a possibility that the ABS indicator may come on due to insufficient battery voltage. After the battery is sufficiently recharged and the engine is turned off and restarted, the ABS indicator should indicate that the ABS is OK, by coming on for a few seconds each time the engine is started. If the indicator remains on after recharging, have it checked by a Honda dealer.

Towing

If towing is necessary, contact a professional towing service. Your authorized Honda dealer can assist you with detailed towing instructions.

Never use tow chains or rope to tow a car; your ability to safely control the car may be adversely affected.

We recommend the following: Flat Bed Equipment —Entire car is winched on a flat bed vehicle. This is the best way of transporting your Honda. Wheel Lift Type —Tow with the front wheels off the ground.

If the car can only be towed with the front wheels on the ground, make sure the transmission is full of fluid (see pages 120 — 121 ), and tow with the transmission in neutral (N) and the ignition key in the I position.

CAUTION: To avoid serious damage on automatic transmission cars, first start the engine and shift to D4, then to N and shut the engine off. If the engine does not run, or the transmission cannot be shifted while the engine is running, the car must be transported on flat bed equipment.

Check local regulations for towing.

CAUTION:

Do not exceed 35 mph (55 km/h) or tow for distances of more than 50 miles (80 km). If a sling type tow is used, the tow truck driver should position wood spacer blocks between your car's frame and the chains and lift straps to avoid damaging the bumper and the body. Do not use the bumpers to lift the car or to support the car's weight while towing.

If Your Car Gets Stuck

If your car gets stuck in sand, mud, or snow, call a professional towing service for assistance in getting your car out.

CAUTION:

Do not rev up the engine and allow the wheels to spin freely at high speed. Severe transmission damage may result if the wheels are allowed to spin for more than a few seconds. DO NOT try to free a car with automatic transmission from snow, etc. by rocking the car alternately between forward and reverse gears. Severe transmission damage may result from shifting into gear with the wheels moving.

Specifications

*1 Including the coolant in the reserve tank 0.6

(0.16 US gal, 0.13 lmp gal) and that

remaining in the engine.

*2 Excluding the oil remaining in the engine. *3 US Cars *4 Canada Cars

page 130.

Identification Numbers

The Vehicle Identification Number (V.I.N.) is stamped on a plate attached to the top left side of the dashboard. It also appears on the Certification label (Canada cars: Canada Motor Vehicle Safety Standard Compliance Label) attached to the driver's door jamb, as well as under the hood on the body, directly behind the engine.

NOTE: The V.I.N. is also provided in bar code on the Certification label.

VEHICLE IDENTIFICATION NUMBER

VEHICLE IDENTIFICATION NUMBER

CERTIFICATION LABEL

ENGINE NUMBER

TRANSMISSION NUMBER

The Engine Number is stamped on the right front side of the engine block. The Transmission Number appears on a label on top of the transmission.

DOT Tire Quality Grades

US Cars The tires on your car meet Federal Safety Requirements. AH tires are also "graded" according to Department of Transportation (DOT) standards for tread wear, traction and temperature.

Three grades are shown on the tire sidewall.

TIRE

WHEEL RIM

Tread Wear The tread wear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one half (1-1/2) times as well on the government course as a tire graded 100. The the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

relative performance of

tires depends upon

Traction The traction grades, from highest to lowest, are A, B, and C, and they represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

The traction grades assigned are based on braking (straight ahead) traction tests and do not include cornering (turning) traction.

(cont'd)

DOT Tire Quality Grades (cont'd)

Temperature The temperature grades are A (the highest), B and C representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

The tire temperature grade is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Emission Controls

Sources of Emissions The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. The evaporation of fuel in the fuel tank also produces hydrocarbons. Control of oxides of nitrogen and hydrocarbons is very important since, under certain conditions, when subjected to sunlight, they react to form photochemical smog. Carbon monoxide does not react to form smog, but it is toxic.

The Clean Air Act The Clean Air Act* requires ail vehicle manufacturers to explain in writing the operation and maintenance of their emission control systems. Maintenance instructions are included on pages 110 — 112; the operation of each system is explained below and on the following page.

Replacement Parts The emission control systems on your new Honda were designed, built and certified the Federal regulations implementing the Clean Air Act. Honda recommends only the use of new, Genuine Honda parts or their equivalent. The use of other replacement parts which are not of equivalent quality may impair the effectiveness of your car's emission control systems.

to conform with

Crankcase Emission Control System To prevent crankcase emissions, your car is equipped with a Positive Crankcase Ventilation (PCV) System which routes blowby gases the Positive Crankcase Ventilation valve and intake manifold, into the combustion chamber.

the crankcase,

through

from

Evaporative Emission Control System The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere. Fuel vapors from the fuel tank are directed into the evaporative emission control canister where they are adsorbed and stored while the engine the engine coolant temperature rises to a certain value, the vapors are drawn into the engine through the throttle body and the intake manifold during normal engine operation.

is stopped or

idling. When

* In Canada, Honda vehicles comply with the Canadian Motor Vehicle Safety Standards (CMVSS) on Emissions valid at the time they are manufactured.

(cont'd)

Emission Controls (cont'd)

Engine Exhaust Controls The engine exhaust emission control systems are designed to control combustion during idle, acceleration, cruise, and deceleration. These systems are entirely separate from the crankcase and evaporative emission control systems described previously.

PGM-FI System The PGM-FI system on this model is a sequential multiport fuel injection. The PGM-FI system consists of three independent sub- systems; Air Intake, Engine Control, and Fuel Control, thus allowing more accurate control of air/fuel ratios under all operating conditions. The Engine Control Module (ECM) detects the amount of air drawn into the cylinders and determines the amount of fuel to be injected to provide the optimum air/fuel ratio for all engine needs.

Ignition Timing Control System This system automatically controls the ignition timing to reduce the amount of HC and NOx.

Three Way Catalytic Converter The catalyst is used to convert hydrocarbons (HC), carbon monoxide (CO) and oxides of nitrogen (NOx) in the exhaust gas, to carbon dioxide (CO

) and water vapor.

), dinitrogen (N

(NOx) caused when

Exhaust Gas Recircutetton (EGR) System The EGR system is designed to control the formation of oxides of nitrogen fuel mixture burns at high temperature. It works by recircuiating exhaust gas through the Exhaust Gas Recirculation valve and intake manifold into the combustion chambers where it reduces peak temperature by diluting the air/fuel mixture.

Three Way Catalytic Converter

A three way catalytic converter is installed in the exhaust system to help clean-up the harmful exhaust gases that can cause air pollution. To be effective, the three way catalytic converter must work at high temperature, so don't park your car over dry grass, leaves or anything else that could burn easily. To stay effective, the three way catalytic converter must not be contaminated by leaded gasoline; use only unleaded gasoline as explained on page 92 .

THREE WAY CATALYTIC CONVERTER

CAUTION: The three way catalytic converter can be overheated and damaged if it's fed too much unowned fuel mixture from the engine, so: —Don't push or tow the car to start it; if the battery is dead, jump

start the car as shown on page 154 .

—Don't turn the key off while the engine is running above idle

speed.

parts.

—Don't change the ignition timing, or remove any emission control

—Use only the spark plugs specified in this manual. —Don't keep driving your car if it isn't running properly, or if its CHARGING system fight comes on; have it checked by your Honda dealer.

Warranty Service

Warranty (US Cars) The following warranties are provided with every new vehicle. 1. New Car Limited Warranty 2. Emission-Related Defects Warranty 3. Emissions Performance Warranty 4. Original Equipment Battery Limited Warranty 5. Rust Perforation Limited Warranty 6. Accessory Limited Warranty 7. Replacement Parts Limited Warranty 8. Replacement Muffler Lifetime Limited Warranty 9. Seat Belt Limited Warranty 10. Replacement Battery Limited Warranty Your car's original tires are covered by their manufacturer. Tire warranty information is in a separate tire warranty booklet. The details of ail warranties pertaining to your car can be found in the Warranty booklet provided with your new car. The required maintenance schedule is contained in this Owner's Manual. If you are unable to obtain warranty service or are dissatisfied with the warranty decision or service you received at an authorized Honda dealership, you should review the matter with that dealership's Service Manager. This will normally resolve your problem. If it does not, you should appeal the decision with the owner of the dealership. Please bear in mind that your problem will likely be resolved in the dealership, using the dealer's facilities, equipment, and personnel. So it is very important that your initial contact be with the dealer or his management.

following these steps,

After to have the matter reviewed by American Honda you should contact the Zone Office serving your area, as shown on the map on the inside of the back cover. When contacting American Honda, please provide the Zone Office with the following information:

if you wish

Vehicle Identification Number Servicing Dealer Name and Address Date of Purchase Mileage on your Car Your Name, Address, and Phone Number Nature of Problem Selling Dealer

After a review of the facts, you will be advised of what can be done.

(Canada Cars) Please refer to the 1993 Warranty and Maintenance Guide that came with your car.

Reporting Safety Defects

(US Cars) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc..

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or American Honda Motor Co., Inc.

To contact NHTSA, you may either call the Auto Safety Hotline toll- free at 1-800-424-9393 (or 366-0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.

Airbag

.......See "Supplemental

Restraint System"

Air Conditioning

Care ........................................ 141
Operation.................................. 64
Air Cleaner................................... 129
Air Pressure, Tires ...................... 137
Aluminum Alloy Wheels.............. 145
Antenna.......................................... 72
Cleaning.................................. 144
Antifreeze .... See "Engine Coolant" Anti-lock Brake System (ABS)..... 34
Anti-lock Brake Fluid............. 126
ABS Indicator........................... 41
Anti-theft Radio............................. 91
Anti-theft Steering Column Lock

System..................................... 96
Appearance Care........................ 143
Ashtrays......................................... 58
Audio System................................. 72
Automatic Transmission

Driving Technique.................. 104
Fluid......................................... 121
Operation .............................. 103
Shift Lever Position Indicator. 38

Battery

Charging System Light............ 39
Jump Starting........................ 154
Maintenance........................... 132
Specification.......................... 159

Beeper System

Fasten Seat Belt Beeper...........12
Key Reminder........................... 96
Light Reminder Chime............. 49

Belt, Seat

..............See "Seat Belt System" Beverage Holder............................. 57
Body Repair.................................. 147
Brake System Light....................... 41
Brakes

ABS Indicator........................... 41
Anti-lock Brake System

(ABS)..................................... 34
Anti-lock Brake Fluid............. 126
Brake Fluid.............................. 126

Index

Brake System Design............ 125
Brake Wear............................ 125
Brake Wear Indicators........... 125
Parking Brake........................... 54
Parking Brake and

Brake System Light............. 41
Break-in Period................................. 2
Bulb

Replacement.......................... 135
Specification.......................... 159
Buzzer........... See "Beeper System"

Capacities..................................... 158
Care and Clearing........................ 143
Certification Label....................... 160
Chains/Tires................................. 138
Check Engine Light........................ 40
Child Safety........................... 2 7-33
Child Seat Locking Clip............ 32
Child Seat Storage................... 33
Guidelines......................... . 28 - 30
Infant Seats.............................. 29
Safety Reminders.................... 28
Seating Location...................... 27
Tethers..................................... 31
Toddler Seats.......................... 30
Cigarette Lighter............................ 58
Clock............................................... 56
Clutch Fluid................................... 127
COMPACT Spare Tire................. 148
Coolant Temperature Gauge........ 37
Cooling (with A/C).......................... 64
Cooling System........................... 122
Crankcase Emission Control

System................................... 163

Cruise Control

Indicator.................................... 38
Operation.................................. 52

Daytime Running Light (DRL)........ 51
DRL Indicator Light.................. 42
Defogger......................................... 47
Defroster........................................ 67
Dimmer Switch, Headlights.......... 49
Doors

Locks....................................3 , 25
(cont'd)

Index (cont'd)

Power Door Locks..................... 4
Warning Light........................... 43

Gauges.............................................. 36
Glove Box........................................ 57

Emergency

Changing Flat Tire.................. 150
Hazard Warning System......... 50
If Your Car Gets Stuck.......... 157
Jump Starting........................ 154
Towing.................................... 156
Warning and indicator Lights.. 38
Emission Controls........................ 163
Engine

Coolant.................................... 122
Coolant Temperature Gauge .. 37
Exhaust Controls................... 164
Identification Number............ 160
Low Oil Pressure Light............ 40
Oil and Filter............................ 117
Specification....................... 159
Engine Exhaust Gas Warning........ 99
Evaporative Emission Control

System................................... 163
Exhaust Gas Recirculation.......... 164
Exterior Care............................... 144

Fitters

Engine Oil................................ 118
Fuel.......................................... 129
Fluid....................................See "Oil" Foreign Countries, Operation in... 93
Front Seat

Adjustment.................................6

Fuel

Fill Door and Cap...................... 94
Filter ....................................... 129
Gasohol..................................... 92
Gasoline.................................... 92
Gauge........................................ 36
Low Fuel Indicator................... 41
Requirement............................. 92

Fuse

Checking and Replacing........ 133
Specification ....................... 159

Gasoline........................... See "Fuel"

Hazard Warning System............... 50
Headlights

Flasher...................................... 49
High Beam Indicator................. 38
High Beam/Low Beam Switch

............................................... 49
Reminder Chime...................... 49
Switch ...................................,.. 49
Head Restraints................................ 7
Heating............................................ 65
High Beam

Indicator.................................... 38
Switch...................................... 48
Hood Latch..................................... 54

Identification Numbers................ 160
Ignition

Keys............................................ 3
Switch...................................... 96
Ignition Switch Light...................... 50
Important Safety Reminders

...................................... 11, 20, 28
Indicator Lights.............................. 38
Inflation Pressures, Tire.............. 137
Instrument Panel............................ 35
Instrument Panel Brightness Control ................................................... 50
Interior Light................................... 5
Interior Trim Care........................ 143

Jack.............................................. 150
Jump Starting.............................. 154

Keys

Door Locks................................. Glove Box................................. 5
Ignition .................................. 9
Key Reminder Beeper............. 9
Keys .......................................... Trunk Lock .................................

Lap Belt........................................... 13
Lap/Shoulder Belt.......................... 12
Lights

Bulb Replacement.................. 135
Daytime Running Lights .......... 51
Fuse Replacement................. 133
Light Reminder Chime............. 49
Operation.................................. 49
Warning and Indicator Light.... 38

Locks

Anti-theft Steering Column Lock ...............................................96
Doors........................................... 3
Fuel Fill Door............................. 94
Glove Box................................. 56
Power Door Lock....................... 4
Trunk........................................... 5
Lumbar Support............................... 8

Maintenance

Indicator.................................... 44
Records.................................. 113
Schedule................................. 110

Manual Transmission

Maximum Allowable Speeds...... 101
Oil............................................ 120
Recommended Shift Speeds..... 101
Shifting................................... 100
Meters, Gauges......... See "Gauges" Mirrors

Manual Mirrors......................... 48
Power Mirrors.......................... 48
Rearview Mirrors..................... 48

Moonroof

If the Moonroof Won't Close.. 71
Maintenance............................ 71
Operation.................................. 70

Numbers, Identification............... 160

Octane Rating,

Gasoline..................... See "Fuel" Odometer....................................... 36

Oil

Clutch Fluid............................. 127
Engine Oil................................ 117
Fluid Locations....................... 116
Low Oil Pressure Light............ 40
Power Steering Fluid............. 128
Transmission Oil/Fluid........... 120
Operation In Foreign Countries.... 93

Panel Brightness Control............... 50
Parking Brake................................. 54
PGM-FI

Check Engine Light.................. 40
Malfunction indicator Lamp.... 40
System................................... 164

Power

Door Locks................................. 4
Mirrors...................................... 48
Steering................................... 128
Windows................................... 55
Pressures, Tire Inflation.............. 137
Preventive Service...................... 146

Radio............................................... 72
Rearview Mirrors...........................48
Rear Quarter Windows................. 56
Rear Window Defogger................. 47
Reminder Lights

.................. See "Warning Lights"

Replacement

Air Cleaner.............................. 129
Bulbs....................................... 135
Engine Coolant....................... 123
Engine Oil................................ 118
Fuel Filter................................ 129
Fuses...................................... 133
Oil Filter................................... 118
Spark Plugs............................ 130
Tires........................................ 139
Wiper Blades.......................... 131
Rust Prevention........................... 145

(cont'd)

Index (cont'd)

Precautions........................... 23

Sefety Defects, Reporting.......... 168
Safety Indicator Lights.................. 43
Safety Items................................... 98
Seat-back Position......................... 24
Seat Belt System........................... 11
Components............................. 12
Lap/Shoulder Belt..............12, 14
Lap Belt.............................. 13, 16
Maintenance............................. 18
Operation.................................. 11
Pregnant Women..................... 18
Reminder Lights and Beeper... 12
Safety Reminders..... 11, 24 - 26
Seat Heater.................................... 69
Seats

Driver's Center Armrest........... 8
Driver's Lumbar Support.......... 8
Front Seat................................... 6
Head Restraints.......................... 7
To Get In/Out of Rear Seat....... 8
Trunk Access from Rear Seat.. 9
Shift Lever Position Indicator....... 38
Shifting

Automatic.............................. 102
5-Speed Manual..................... 100

Spare Tire

Changing a Fiat Tire............... 150
COMPACT Spare Tire........... 148
Specifications......................... 158
Spark Plugs.................................. 130
Specifications.............................. 158
Speedometer................................. 36
SRS Indicator Light........................ 42
Starting the Engine........................ 97
Steering

Anti-theft Column Lock.......... 96
Power Steering...................... 128
Tilt Steering.............................. 45

Stereo Sound System

Operation.................................. 72
Stuck Car..................................... 157
Sunshade........................................ 70
Supplemental Restraint

System (SRS)................... 19 - 23
Components............................. 20
Indicator Light........................... 22
Operation.................................. 21
Safety Reminders.............. 20, 24
System Service........................ 23

Tachometer.................................... 36
Temperature Gauge, Coolant....... 37
Tilt Steering....................................45
Tire

Air Pressure........................... 137
Balancing................................ 140
Chains..................................... 138
Changing a Flat Tire............... 150
COMPACT Spare.................. 148
DOT Tire Quality Grades ...... 161
Inflation Pressures................. 137
Requirement........................... 161
Rotation.................................. 140
Snow Tires............................. 138
Spare Tire............................... 148
Specification.......................... 158
Tools............................................. 150
Towing.......................................... 156
Towing a Trailer........................... 105
Transmission

Capacity.................................. 158
Identification Number............ 160
Oil/Fluid................................... 120
Shifting the Automatic.......... 102
Shifting the Manual................ 100
Tread Wear.................................. 161
Trip Meter...................................... 36
Trunk

Access From Rear Seat............ 9
Lid................................................ 5
Lid Warning Light..................... 43
Turn Signals.................................... 49

Vanity Mirror.................................. 58
Vehicle Identification Number.... 160
Ventilation...................................... 59

Warning Lights............................... 38
Warranty Service........................ 166
Washar

Reservoir Capacity.................. 46
Windshield Washer.................. 46
Washing........................................ 144

Waxing......................................... 144
Wearing Seat Belts Properly ........ 13
Wearing the Lap Belt .................... 16
Wearing a Lap/Shoulder Belt........ 14
Wheels.......................................... 145
Windows

Appearance Care.................. 143
Power Windows...................... 55
Windshield Defogger..................... 47
Windshield Washer....................... 46
Windshield Wipers........................ 46
Wiper Blades................................ 131
Wipers............................................ 46

Your Occupant Protection

System...................................... 10

Authorized Manuals

Purchasing Factory Authorized Manual (U.S. only) The following publications covering the operation and servicing of your vehicle can be obtained from Helm Incorporated either by filling out the reverse side of this form or, for credit card holders, calling the toll free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O.Box 07280, Detroit, Michigan 48207, or call (313) 883-1430.

61SM405

61SM405EL

61SM431

31SM2630

HON-R

Service Manual This manual covers maintenance and recommended procedures for repair to engine and chassis components, It is written for the journeyman mechanic, but is simple enough for most mechanically- irtcSned owners to understand.

Electrical Troubleshooting Manual This manual complements the Service Manual by providing in-depth troubleshooting information for each electrical circuit in your car.

Body Repair Manual This manual describes the procedures involved in the replacement of damaged body parts.

Valid on/y for sales within the U.S. Canadian owners should contact their authorized Honda dealer.

By completing this form you can order the materials desired. You can pay by check or money order, or charge to your credit card. Mail to Helm, Incorporated at the address shown below.

P.O. BOX 07280 DETBOTT, MICHIGAN 482O7 (313) 883-1430

Honda Canada

Atlantic Zone Honda Canada Inc. 800 Windmill Road Dartmouth, N S. B3B ILI (902) 468-4416

Western Zone Honda Canada Inc. 13240 Worster Court Richmond, B.C. V6V 2B8
(604)278-7121

Prairie Zone Honda Canada Inc. 1839 Inkster Blvd. Winnipeg, Manitoba R2X IR3
(204)632-8650

Central Zone Honda Canada Inc. 305 Milner Avenue Suite 105
Scarborough, Ontario M1B 3V4
(416) 299-3400

Quebec Zone Honda Canada Inc. 1750 rue Eiffel Boucherville, Quebec J4B 7W1
(514)655-6161

The above addresses and telephone numbers are subject to change. If you cannot reach your Zone office, ask your Honda dealer for the current information.

1993 Accord Coupe Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com.

Contents

Owner's Identification Form Features & Safety ................................................................................................................................ 2
What you should know before driving your car. Starting & Driving............................................................................................................................. 92
What gas to use, how to change gears, etc. Maintenance ..................................................................................................................................... 110
The Required Maintenance Schedule and some items you can service. Emergency Service .......................................................................................................................... 148
Changing a flat, jump starting, towing. Specifications ................................................................................................................................... 158
Dimensions, weights and capacities. Consumer Information .................................................................................................................... 160
Reporting Safety Detects, warranty service, vehicle identification numbers, etc. Index ................................................................................................................................................ 169

Introduction

This manual contains operation and maintenance of your car.

important

information about

the safe

We urge you to read it carefully, become familiar with the controls it describes, and follow its recommendations, to help make your driving trouble-free and enjoyable.

Statements or labels on the product preceded by the following words are of special significance:

indicates severe personal injury or death will result if instructions are not followed.

indicates a strong possibility of severe personal Injury or death if instructions are not followed.

CAUTION: means hazards or unsafe practices which could cause minor personal injury or product or property damage.

NOTE:

gives helpful information.

Break-in Period During the first 600 mites (1,000 km) of driving, avoid full throttle starts and cruising for extended periods at a constant speed.

NOTE:

This break-in procedure also applies to exchanged or overhauted engines. During and after the break-in period, drive the car at moderate speeds until the engine is fully warmed up.

During the first 200 mites (300 km), try to avoid severe braking Brake misuse during this period will reduce future braking efficiency Remember, your Honds Automobile dealer knows your car best, and should be consulted for service assistance and advice.

Keys and Locks

VALET KEY

MASTER KEY

release, rear seat

Keys Your car is supplied with a master key that fits the ignition and all locks, and a valet key that fits the ignition and doors but not the trunk, trunk remote trunk access or glove box. The valet key is provided for times when you must leave the key with a parking attendant or repair person, but still want to keep valuables safely locked-up. Write down the numbers stamped on both keys and keep the information in your wallet or purse in case you ever need to have duplicates made. Both the master and vatet keys are double-edged, so you can insert them in the locks with either side up.

Door Locks You can lock the doors by pushing the tabs forward. The doors must be unlocked before you can open them. The passenger door can be locked when open, and will stay locked when you close it; the driver's door cannot be locked when open unless you hold the door handle open. Both doors can be locked and unlocked from the outside with the key.

Unlock

Lock

(cont'd)

Keys and Locks (cont'd)

Power Door Locks (US: LX/EX/SE, Canada: EX-R/SE) Both doors can be simultaneously locked and unlocked by operating the master door lock switch located on each door.

MASTER DOOR LOCK SWITCH

Unlock

Lock

In addition, the passenger door will lock automatically when the tab on the driver's door is pushed forward, or when the driver's door is locked from the outside with the key.

Lock

Lock

Unlock

Trunk The trunk can be opened by putting up the lever at the l e ft side of the driver's seat. To open the trunk lid from the outside, put the master key in the lock and turn clockwise. The trunk lid opener lever is lockable with the master key.

Pull up

Lock

MASTER KEY

Open

Keep the trunk fid closed white driving to keep poisonous carbon monoxide exhaust fumes out of the interior; prolonged exposure can cause unconsciousness that may lead to death.

Seats

Front Seat Adjust the seat position by pulling up on the adjustment lever under the front edge of the seat cushion, and sliding the seat to the desired position. Then release the lever and make sure the seat is locked in position by moving it back and forth.

Pull up

Pull up

ADJUSTMENT LEVER

RELEASE LEVER

The angle of the seat-back can be changed by pulling up on the lever at the outside edge of the seat and leaning forward or back. Release the lever and let the seat lock into place when it reaches the desired angle. Seat belts are most effective when the driver and passenger are sitting up straight and well back in each seat.

Do not adjust the driver's seat while the car is moving; the seat could move suddenly, causing loss of vehicle control. To reduce the risk of sliding under the seat belts in a collision, adjust the seat-backs to an upright position and sit well back in the seat.

Front Seat Head Restraints The head restraints are designed to help reduce injuries due to whiplash. They are located at the top of each front seat-back and have several height positions. They can be adjusted by pulling up to the recommended position. To lower them, slide the button next to the restraint's height bar, while pushing the restraint down. Adjust so the top of the restraint is approximately level with the tops of your ears. If a head restraint must be removed (for cleaning, fabric repair, etc.) pull the restraint up to its highest position, then slide the button while pulling the restraint out. To reinstall, reverse the above procedure.

Slide

Do not drive the car with head restraints removed. Do not try to adjust head restraints white driving.

(cont'd)

Seats (cont'd)

Driver's Lumbar Support (US: EX/SE, Canada: EX-R/SE) Support of the lower back can be adjusted by turning the knob on the driver's armrest to give more or less support.

Do not try to adjust lumbar support white driving. Make the adjustment white sitting in your normal driving position before driving away.

Driver's Seat Center Armrest (US: LX/EX/SE, Canada: EX-R/SE) The angle of the driver's armrest on the driver's seat adjusts five positions. To the armrest, push the button on the driver's side of the armrest.

the armrest and

lower

tower

to

Do not try to adjust the armrest while driving. Make the adjustment before driving away.

Push

To Get In/Out of Rear Seat For easier access to or from the rear seat, pull up the angle adjust- ment lever on each front seat to swing the seat-back forward. The front passenger seat has an additional convenience: pulling up the the passenger seat-back will swing the seat-back and slide the entire seat forward.

inside of

lever on

the

Pull up

Trunk Access from Rear Seat The rear seat-back can be released by turning the lock on the rear shelf with the master key and pulling down the top of the seat-back. This allows you access to the trunk and makes it possible to carry long objects inside the car. The rear seat-back can also be released from inside the trunk by pulling the release.

Open

MASTER KEY

Pull

RELEASE

Passengers or pets must not sit on the folded portion of the rear seat. Make sure any luggage or cargo within the trunk, or extending through the rear seat trunk access is secured. Make sure the seat-back latches engage securely when the seat-back is returned to its normal position. Weight limits shown on the label located on the driver's door jamb must be observed. The total weight of passengers and cargo must not exceed the total weight limit on the label. Do not store any items on the shelf behind the rear seat; they may become dangerous projectiles in a collision. Store any luggage or cargo in the trunk. If you are carrying more items than will fit in the trunk, use the floor space between the front and rear seats. Make sure both rear shoulder belts are positioned In front of the rear seat-backs whenever the seat-backs are in their upright position.

When closing the rear seat trunk access, push the seat-back firmly into place, then pull on the top of the seat-back to make sure it is secure.

Your Occupant Protection System

Your Accord is equipped with seat belts and other features that work together to protect you and your passengers during a crash.

Seat belts are the most important part of your occupant protection system. When worn properly, seat belts can reduce the chance of serious injury or death in a crash.

For added protection during a severe frontal collision, all Accords have a Supplemental Restraint System (SRS) with a driver's airbag.

Two indicator lights are also part of your safety system. One reminds you to make sure you and your passengers wear your seat belts. The other alerts you to a possible problem with your supplemental restraint system (see page 22 ).

The seats, head restraints, and door locks also play a role in occupant safety. For example, reclining your seat-back can decrease the effectiveness of your seat belt. Head restraints can help protect your neck and head, especially during rear-end impacts. Door locks help keep your doors from being accidentally opened during a crash.

To get the maximum protection from your occupant protection system, check the following before you drive away:

Everyone in the car is wearing a seat belt properly (see page 13 ).

Infants and small children are properly secured in child safety seats (see page 27 ).

All doors are closed and locked (see page 25 ).

Seat-backs are upright and head restraints are properly adjusted (see page 2 4).

There are no loose items that could be thrown around and hurt someone during a crash or sudden stop (see page 25 ).

By following these guidelines, you can reduce injuries to yourself and your passengers in many crash situations. Remember, however, that no safety system can prevent all injuries or deaths that can occur in severe crashes.

The Seat Belt System and How It Works

Why Wear Seat Belts Wearing seat belts, and wearing them properly, is fundamental to your safety and the safety of your passengers.

During a crash or emergency stop, seat belts can help keep you from being thrown against the inside of the car, against other occupants, or out of the car.

Of course, seat belts cannot completely protect you in every crash. But, in most cases, seat belts reduce your chance of serious injury, and can even save your life. That is why many states and all Canadian provinces require you to wear seat belts.

Not wearing a seat belt increases the chance of being killed or seriously hurt in a crash.

Be sure you and your passengers always wear seat belts and wear them properly.

Important Safety Reminders Seat belts are designed for adults and larger children. All infants and small children must be properly restrained in child safety seats (see page 27 ).

A pregnant woman needs to wear a seat belt to protect herself and her unborn child (see page 18 ).

Two people should never use the same seat belt. If they do, they could be very seriously injured in a crash.

Do not place the shoulder portion of a lap/shoulder belt under your arm or behind your back. This could increase the chance of serious injuries in a crash.

Do not put shoulder belt pads or other accessories on seat belts. They can reduce the effectiveness of the belts and increase the chance of injury.

(cont'd)

The Seat Belt System and How It Works (cont'd)

Seat Belt System Components Your Accord has seat belts in all five seating positions. The front seats and the outside positions of the rear seat have lap/shoulder belts. The center position of the rear seat has a lap belt.

Your seat belt system also includes a light on the instrument panel to remind you to fasten your seat belt, and to make sure your passengers fasten theirs. This light comes on when you turn on the ignition if you have not fastened your seat belt. A beeper also sounds for several seconds (see page 39 ).

The following pages cover more about the seat belt components and how they work.

Lap/Shoulder Belt This style of seat belt has a single belt that goes over your shoulder, across your chest, and across your hips.

Each lap/shoulder belt has an emergency locking retractor. In normal driving, the retractor lets you move freely in your seat while it keeps some tension on the belt. During a collision or sudden stop, the retractor automatically locks the belt to help restrain your body.

SHOULDER PORTION

LATCH PLATE

BUCKLE

UPPER SEAT BELT ANCHOR

To retractor

LAP PORTION

Lap Belt The tap belt has one manually-adjusted belt that fits across the hips. It is similar to safety belts used in airplanes.

LATCH PLATE

BUCKLE

Wearing Seat Belts Properly You can increase the effectiveness of your seat belts if you take a little time to read the following pages and make sure you know how to wear seat belts properly.

Not wearing a seat belt properly increases the chance of serious injury or death in a crash.

Be sure you and your passengers always wear seat belts and wear them properly.

(cont'd)

The Seat Belt System and How it Works (cont'd)

Wearing a Lap/Shoulder Belt Before putting on a front seat belt, be sure your seat is adjusted forward or backward to a good driving or riding position and the back of your seat is upright (see page 24 ).

1. Pull the latch plate across your body and insert it into the buckle.

Tug on the belt to make sure the latch is securely locked.

2. Check that the belt is not twisted.

3. Position the lap portion of the belt as tow as possible across your hips, not across your stomach. This lets your strong pelvic bones take the force of a crash.

4. Pull up on the shoulder part of the belt to remove any slack. Make

sure the belt goes over your collarbone and across your chest.

5. Rear Seat:

If the belt crosses your neck, you should adjust your seating position. Move toward the center of the seat until the belt fits over your collarbone.

(cont'd)

The Seat Belt System and How It Works (cont'd)

To unlatch the seat belt, push the red PRESS button on the buckle. Guide the belt across your body to the door pillar. If the belt doesn't retract easily, pull it out and check for twists or kinks.

Wearing the Lap Belt 1. Pull the latch plate across your hips and insert it into the buckle

marked CENTER.

If the belt is too short, hold the latch plate at a right angle and pull to extend the belt. Insert the latch plate into the buckle.

2. Position the belt as low as possible across your hips and pelvic bones, not across your stomach. Pull the loose end of the belt to adjust for a snug but comfortabte fit.

To unlatch the belt, push the red PRESS button on the buckle.

(cont'd)

The Seat Belt System and How it Works (cont'd)

Advice For Pregnant Women Protecting the mother is the best way to protect her unborn child. Therefore, a pregnant woman should wear a properly-positioned seat belt whenever she drives or rides in a car.

If possible, use the tap/shoulder seat belt, remembering to keep the lap portion as low as possible (see page 14 ). Each time you have a check-up, ask your doctor if it's okay for you to drive and how you should position a lap/shoulder seat belt.

Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly.

Pull out each belt fully and look for frays, cuts, burns, and wear. Check that the latches work smoothly and the lap/shoulder belts retract easily. Any belt not in good condition or not working properly should be replaced.

If a seat belt is worn during a crash, have your dealer replace the belt and inspect the anchors for damage.

If your seat belts get dirty, you can use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. They can weaken the belt material. Let the belts air-dry before you use the car.

Dirt build-up in the metal loops of the seat belt anchors can cause the belts to retract slowly. Wipe the inside of the loops with a clean cloth dampened in isopropyl alcohol or a mixture of mild soap and warm water.

Supplemental Restraint System

All Accords are equipped with a Supplemental Restraint System (SRS) to help protect your head and chest during a severe frontal collision. This system does not replace your seat belt. It supplements, or adds to, the protection offered by your seat belt.

Not wearing a seat belt increases the chance of serious injury or death in a crash, even if you have an airbag.

Be sure you and your passengers always wear seat belts and wear them properly.

S R S

AIRBAG

RIGHT SENSOR

LEFT SENSOR

SRS CONTROL UNIT

The main components in your SRS are:

An airbag in the steering wheel for the driver.

A diagnostic system that, when the ignition is ON (II), continually monitors the sensors, control unit, airbag activator, and all related wiring.

An indicator light to warn you of a possible problem with the system.

Emergency power backup in case your car's electrical system is disconnected in a crash.

(cont'd)

Supplemental Restraint System (cont'd)

Important Safety Reminders

FRONTAL COLLISION RANGE

Even with an airbag, you need to wear a seat belt. The reasons are:

Airbags only inflate in severe frontal collisions. They offer no protection in rear impacts, side impacts, rollovers, or moderate frontal collisions.

An airbag inflates and deflates very quickly. It cannot protect you during any additional impacts that can occur during a crash.

A seat belt helps keep you in the proper position when an airbag inflates. An airbag opens with considerable force and can hurt you if you are not in the proper position.

How the Driver's Airbag Works if you ever have a severe frontal collision, your airbag will instantly inflate to help protect your head and chest.

When the airbag inflates, you may hear a fairly loud noise and you might see smoke and powder. This is normal; it is caused by the inflation of the airbag.

To do its job, the airbag inflates with considerable force. So, white it can reduce serious injuries and even save your life, the airbag might cause some facial or other abrasions.

(cont'd)

Supplemental Restraint System (cont'd)

After the bag completely inflates, it immediately starts deflating so it won't interfere with your visibility, ability to steer, or ability to operate other controls.

The airbag is stored in the center of the steering wheel. For your safety, do not attach any items to the steering wheel. They could interfere with the proper operation of the airbag. Or, if the airbag inflates, they could be propelled inside the car and hurt someone.

S R S

How the SRS indicator Light Works

The purpose of the SRS light on your instrument panel is to alert you of a potential problem with your supplemental restraint system.

Have the system checked if:

The light does not come on when you turn the ignition ON (II).

The light stays on after the engine starts.

The fight comes on or flashes white you are driving.

System Service Your supplemental restraint system is virtually maintenance-free. There are no parts you can safely service.

You must have the system serviced by an authorized Honda deafer:

If your airbag ever inflates. The airbag must be replaced. Do not try to remove or discard the airbag by yourself. This must be done by a Honda dealer.

If the SRS indicator light alerts you of a problem. Have the supplemental restraint system checked as soon as possible. Otherwise, your airbag might not inflate when you need it.

When the car is ten years old. Have the dealer inspect the system. The production date is on the driver's door jamb for your convenience.

System Service Precautions Do not modify your steering wheel or any other part of the supplemental restraint system. Modifications could make the system ineffective.

Do not tamper with the system components or wiring. This could cause the airbag to inflate inadvertently, possibly injuring someone very seriously.

Tell anyone who works on your car that you have a supplemental restraint system. Failure to follow the procedures and precautions in the official Honda service manual could result in personal injury or damage to the system.

Scrapping an entire car that has an uninflated airbag can be dangerous. Get assistance from a Honda dealer if your car must be scrapped.

If you sell your car, please be sure to tell the new owner that the car has a supplemental restraint system. Alert them to the information and precautions in this part of the owner's manual.

Additional Safety Information

Your seat belts and airbag are obviously important parts of your occupant protection system.

In addition, you should know that sitting upright, adjusting the head restraints to the proper positions, locking the doors, and stowing things properly can also increase your safety and possibly even save your life.

Seat-back Position The seat-backs should be in an upright position for you and your passengers to get the most protection from the seat belts.

If you recline a seat-back, you will reduce the protective capability of your seat belt. The farther a seat-back is reclined, the greater the risk that you will slide under the belt in a severe crash and be very seriously injured.

For information on how to adjust the seat-back, see page 6 .

Head Restraint Position Head restraints can help protect you from whiplash and other injuries. For the best protection, adjust the top of the head restraint so it is even with the tops of your ears, or as high as possible. For instructions on adjusting the head restraints, see page 7 .

Door Locks It is not safe to leave your car doors unlocked. A passenger, especially a child, could open a door and accidentally fall out. Also, there is a greater chance of being thrown out of the car during a crash when the doors are not locked.

Storing Cargo Safely Before you drive, make sure you first securely store or tie down any items that could be thrown around the car and hurt someone, or interfere with your ability to operate the controls.

Do not put any items on top of the rear shelf. They can block your view and they could be thrown about the car in a crash.

Be sure to keep compartment doors closed when the car is moving. If a front passenger hits the door of an open glove box, for example, he could injure his knees.

(cont'd)

Additional Safety Information (cont'd)

Driving With Pets Loose pets can be a hazard while you are driving. An unrestrained pet can interfere with your ability to drive the car. in a crash or sudden stop, loose pets or cages can be thrown around inside the car and hurt you or your passengers. It is also for their safety that pets should be properly restrained in your car.

The recommended way to restrain a medium-sized or larger dog is with a special traveling harness. This harness can be secured to the rear seat with a seat belt. Travel harnesses are available at pet stores.

A small dog, cat, or other small animal will be safest in a pet carrier with rigid sides. Choose a style that allows you to secure it to the car's seat by routing a seat belt through the carrier's handle.

For further information, contact your veterinarian or local animal protection society.

Child Safety

Children depend on adults to protect them. To help make sure we do, every state and Canadian province has taws requiring infants and young children to be properly restrained whenever they ride in a car.

An infant or child who is not properly restrained can be killed or seriously injured in a crash.

Be sure any child too small for seat belts is properly secured in a child restraint.

Where Should Children Sit? According to accident statistics, children of all sizes and ages are safer when they are properly restrained in the rear seat rather than the front seat.

We recommend that, whenever possible, you secure your child's infant or toddier seat in the center position of the rear seat with the lap belt.

We also recommend that any child who is too large to use an infant or toddler seat ride in one of the outside positions of the rear seat. The child should then wear the lap/shoulder belt properly for protection.

(cont'd)

Child Safety (cont'd)

Important Safety Reminders Never hold a baby or child on your lap when riding in a car. If you are wearing your seat belt, the violent forces created during a crash will tear the child from your arms. The child could be seriously hurt or killed.

If you are holding a child and not wearing a seat belt in a crash, you could crush the child against the inside of the car.

Never put your seat belt over yourself and a child. During a crash, the belt could press deep into the child, causing serious internal injuries.

Two children should never use the same seat belt. If they do, they could be very seriously injured in a crash.

General Guidelines for Restraining Children Under 40 Pounds (18kg) Use an approved child seat. The seat must meet Federal Motor Vehicle Safety Standard 213 (FMVSS-213) or Canadian Motor Vehicle Safety Standards. Look for the manufacturer's statement of compliance on the box and seat.

Use a seat of the right size. Make sure the seat fits your child. Check the seat's instructions and labels for height and weight limits.

Secure the child seat to the car. All approved child seats are designed to be secured to the car seat by the lap belt or the lap belt portion of a lap/shoulder belt. A child whose seat is not properly secured to the car can be endangered in a crash.

To properly route a seat belt through a child seat, follow the seat maker's instructions. If you use a lap/shoulder belt, be sure you install a locking clip on the belt (see page 32 ).

Secure the child in the child seat. Make sure the infant or child is firmly secured to the child seat. Use the straps provided, and carefully follow the manufacturer's instructions.

Restraining an Infant Who Weighs Less Than 20 Pounds (9 kg) An infant up to about 20 pounds (9 kg) must be restrained in an infant seat or a convertible seat designed for a baby. Because infants must ride in a reclining position, be sure the infant seat always faces the REAR of the car as shown.

We recommend that, whenever possible, you put the infant seat in the center position of the rear seat and secure it to the car with the lap belt.

If you decide to put an infant seat in any other seating position, you must use a locking clip on the car's lap/shoulder belt (see page 32 ).

(cont'd)

Child Safety (cont'd)

Restraining a Child Who Weighs Between 20 and 40 Pounds (9 —18 kg)

Toddler seats are designed for children who weigh between 20 and 40 pounds (9 — 18 kg). The preferred place to put a toddler seat is the center position of the rear seat. Use the car's lap belt to secure the seat to the car.

If you decide to put a toddler seat in any other seating position, you must use a locking clip on the car's lap/shoulder belt (see page 32 ).

Restraining a Child Who Weighs Over 40 Pounds (18 kg) We recommend that, whenever possible, a chad who has outgrown a toddter seat ride in one of the outside positions of the rear seat and use a lap/shoulder belt.

Put the lap/shoulder belt on your child and check its fit. The shoulder belt should fit over the collarbone and across the chest. The lap belt should sit tow on your child's hips, not across the stomach.

If the shoulder belt crosses the neck, have your child move toward the center of the rear seat until the belt fits properly. If the belt still crosses the child's neck, you should use a booster seat.

Several styles of booster seats are available. We recommend a design that aflows the child to use the car's lap/shoulder belt.

Whatever style is used, follow the booster seat manufacturer's instructions.

(cont'd)

Child Safety (cont'd)

Using a Seat Belt Locking Clip Always use a seat belt locking clip when you secure a child seat to your car with a lap/shoulder seat belt. This helps prevent a child seat from shifting position or overturning.

A locking clip is usually included with the child seat. If you need a clip, contact the seat's manufacturer or a store that sells child restraints.

To install a locking clip, do the following:

1. Place the child restraint in the desired position. Route the lap/ the seat

restraint according

to

shoulder belt the manufacturer's instructions.

through

2. Insert the latch plate into the buckle. Pull on the shoulder part of

the belt to make sure there is no slack in the lap portion.

3. Tightly grasp the belt near the latch plate. Pinch both parts of the belt together so they won't slip through the latch plate. Unbuckle the seat belt.

4. Install the locking clip as shown. Position the clip as close as

possible to the latch plate.

5. Insert the latch plate into the buckle. Push and pull on the chile seat to verify that it is held firmly in place. If it is not, repeat these steps until the restraint is secure.

Using Child Restraints With Tethers Your Honda has three attachment points for tether-style child seats. Remove the plug cover from the attachment points shown in the illustration, then install the tether hardware that came with the child seat. Tighten the bolt to: 22 N.m (2.2 kg-m,16 lb-ft)

If you are not sure how to install the bracket, have it installed by your Honda dealer.

If you need an anchor plate and mounting hardware, you can obtain them by writing to:

American Honda Motor Co., Inc. Consumer Affairs 1919 Torrance Blvd. Torrance, CA 90501-2746

Canadian Cars The anchor plate and mounting hardware for a top tether are supplied with the car. When installing, make sure the toothed washer is on the bottom of the bolt.

The supplied anchor plate is designed only for mounting a child restraint. Do not use it for any other purpose.

Storing a Child Seat When you are not using an infant seat or other child restraint, either remove it or make sure it is properly secured so it cannot be thrown around the car during a crash.

Anti-lock Brake System (ABS)

Anti-lock Brakes (US: EX/SE, Canada: EX-R/SE) Your car has an Anti-lock Brake System (ABS). This system helps you to maintain stopping and steering control. It does this by helping to prevent the wheels from locking up and skidding.

The ABS is always "ON". It requires no special effort or driving technique. You will feel a pulsation in the brake pedal when the ABS activates.

Activation varies with the amount of traction your tires have. On dry pavement, you will need to press on the brake pedal very hard before you feel the pedal pulsation that means the ABS has activated. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice. Under all conditions, the ABS is helping to prevent the wheels from locking so you can retain steering control. You should continue to press on the brake pedal with the same force. You may feel a slight movement of the brake pedal just after you start the engine. This is the ABS working.

is self-checking.

If The ABS anything goes wrong, the ABS indicator on the instrument panel comes on (see page 41 ). This means the Anti-lock function of the braking system has shut down. The brakes still work like a conventional system providing normal stopping ability. You should have the dealer inspect your car as soon as possible.

A B S

The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the car. Tire size and construction can affect wheel speed and may cause the system to work inconsistently.

A car with an ABS may require a longer distance to stop on loose or uneven surfaces than an equivalent car without ABS. The ABS cannot make up for road conditions or bad judgment. It is still your responsibility to drive at reasonable speeds for weather and traffic conditions, and to leave a margin of safety.

CAUTION: Be careful not to damage the wiring or the spaed sensors at the back of each wheel when removing mud or snow from the wheel housings.

Instrument Panel

CRUISE CONTROL MASTER SWITCH (Except US: DX)

MOONROOF SWITCH (US: EX/SE, Canada: EX-R/SE)

LIGHT SWITCH

WIPER/WASHER SWITCH

HAZARD WARNING SWITCH

DIGITAL CLOCK

REAR WINDOW DEFOGGER SWITCH

COIN BOX

FUSE BOX

IGNITION SWITCH

HOOD RELEASE HANDLE

TILT STEERING ADJUSTMENT LEVER

US Car Shown:

ASHTRAY

PANEL BRIGHTNESS CONTROL KNOB

HEATING/ COOLING CONTROL P A N E L

CIGARETTE LIGHTER

GLOVE BOX

TACHOMETER

SPEEDOMETER

FUEL GAUGE

SHIFT LEVER POSITlON INDICATOR (Automatic Trans. only)

COOLANT TEMPERATURE GAUGE

MAINTENANCE INDICATOR

TRIP METER

ODOMETER

TRIP METER RESET BUTTON

SAFETY INDICATOR LIGHTS

Gauges

Speedometer US Cars: The speed is indicated in mites per hour (outer scale) and kilometers per hour (inner scale). Canada Cars: The speed is indicated in kilometers per hour (outer scale) and mites per hour (inner scale).

indicate miles (US Cars) or

Odometer The numbers on the odometer kilometers (Canadian Cars). The odometer registers total distance traveled, and serves as your guide for determining when periodic maintenance is due. US Cars: Federal law makes it illegal to alter the odometer of any motor vehicle with the intent to change the number of mites indicated.

Trip Meter The numbers on the trip meter indicate mites (US Cars) or kilometers (Canadian Cars). The trip meter can be returned to zero by pushing in the reset button. Use it for checking fuel consumption or distance traveled per trip.

Tachometer The tachometer indicates engine speed in revolutions per minute. The beginning of the RED ZONE indicates the maximum allowable engine R.P.M. Do not run the engine with the tachometer indicator needle in the RED ZONE.

(17.04 US gal, 14.19 Imp gal)

Fuel Gauge FUEL TANK CAPACITY: Approx. 64.5 As a convenience, the gauge continues to show the same fuel level as when the ignition was last on. After refueling, the gauge will slowly change to the new fuel level when the ignition is switched on. When the needle first indicates E (empty), you have a usable reserve left in the tank of about:

(1.1 US gal, 0.9 Imp gal)

Coolant Temperature Gauge

Do not remove the radiator cap when the engine is hot. The coolant is under pressure and may blow out and scald you.

This gauge shows the temperature of the engine coolant. During normal operation, the needle should stay in the middle of the white range. Under severe driving conditions, such as hot weather or driving uphill for a long period, the needle may rise toward the upper section of the white range. if the needle reaches the red line at " H" (Hot), pull safely off the road and stop the engine. Wait until the engine is cool and check the coolant level in the reserve tank on the passenger side of the radiator under the hood. (See pages 122 — 123.)

Warning and Indicator Lights

US Car Shown:

Shift Lever Position Indicator (Automatic Transmission only) gauges shows which gear you have selected.

lighted indicator between the fuel and coolant temperature

D4 Indicator Light (Automatic Transmission only)

The D4 indicator light in the instrument panel also serves a second function. If the light flashes while driving (in any gear range) it indicates a possible malfunction in the transmission; avoid rapid acceleration and have the transmission checked by an authorized Honda dealer as soon as possible.

Turn Signal and Hazard Warning indicators

When the turn signal lever is pushed for left or right turns, the appropriate green indicator arrow on the instrument panel will blink along with the signal. Pushing the hazard warning switch will make all turn signals and both arrows blink (see page 50 ).

High Beam Indicator

This blue indicator light will go on whenever the high beams are switched on (see page 49 ). (Canada Cars) ft will also go on with a reduced brightness when the Daytime Running Lights (DRL) are on (see page 51 ).

Cruise Control Indicator (Except US: DX)

When the cruise control system is on, this indicator light is on (see pages 52 and 53 ).

Seat Belt Reminder Light

The seat belt reminder light comes on if the driver's seat belt is not fastened, when the ignition switch is turned on. It stays on until the driver fastens his seat belt. (See page 12.)

Charging System Light

The charging system light comes on when there is a problem with the electrical charging system or when the ignition switch is turned on with the engine not running. If the light comes on white driving, get off the road, stop the car and turn off the ignition. Then check the alternator belt for proper tension. To check the belt tension, push with about 98 N (22 Ib) of force on the middle of the belt as shown. The belt should deflect about: 1 0 - 12 mm (0.4-0.5 in)

If the engine has been running, some engine components may be hot enough to burn you. Keep hands away from the radiator fan. The fan may start automatically without warning and run for up to 15 minutes, even after the engine is turned off.

NOTE: If necessary, have the charging system checked by an authorized Honda dealer.

(cont'd)

Warning and Indicator Lights (cont'd)

US

Canada

Malfunction Indicator Lamp

Check Engine Light

This fight comes on for a couple of seconds each time the ignition is turned on. It will also come on, and remain on, if there is a malfunction in the emission control system. If the light comes on while driving, avoid driving at high speed, and have the system checked by a Honda dealer as soon as possible.

Low Oil Pressure Light

A severe fluctuation in engine oil pressure will cause this light to flash on and off. You should pull safely off the road and stop the car. When the engine has cooled down, check the oil level, and add oil if necessary. The low oil pressure light will come on, and remain on, if there is insufficient oil pressure or when the ignition switch is turned on with the engine not running. If the light should come on while driving, get the car off the road as soon as you can, turn the engine off and check the engine oil level (see page 117). Even if the oil level is correct, the engine should be checked by a Honda dealer before the car is driven again.

CAUTION: Running the engine while the low oil pressure fight is on constantly may cause immediate and severe engine damage.

NOTE: The tow oil pressure light will only tight as a result of tow oil pressure. It is not directly an oil level indicator.

US

Canada

Parking Brake and Brake System Light

Check this light every time you start the car. With the parking brake set, this fight should go on when the ignition switch is turned to II or III. With the parking brake released, the light should go on for a few seconds when the ignition switch is turned to III. If the light goes on at any other time, it means the brake fluid level in the master cylinder reservoir is too low; add fluid (see page 126) and have your dealer check for teaks immediately.

Low Fuel indicator

If this indicator glows, it means you should refuel, because the tank contains less than: 8.0

(2.11 US gal, 1.76 Imp gal)

A B S

Anti-lock Brake System (ABS) indicator (US: EX/SE, Canada: EX-R/SE)

The ABS indicator will come on, and remain on, if there is a malfunction in the ABS or when the ignition switch is turned on