2006 GMC Sierra Owners Manual

damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on your vehicle.

Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible. Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Washing with water is all that is usually needed. However, you may use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts.

5-117

Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap, or other material may be on the blade or windshield. Clean the outside of the windshield with a glass cleaning liquid or powder and water solution. The windshield is clean if beads do not form when it is rinsed with water. Grime from the windshield will stick to the wiper blades and affect their performance. Clean the blade by wiping vigorously with a cloth soaked in full-strength windshield washer solvent. Then rinse the blade with water. Check the wiper blades and clean them as necessary; replace blades that look worn.

If you use strong soaps, chemicals,

Aluminum or Chrome-Plated Wheels The vehicle may be equipped with either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. Notice: abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s). The repairs would not be covered by your warranty. Use only GM-approved cleaners on aluminum or chrome-plated wheels. The surface of these wheels is similar to the painted surface of your vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because you could damage the surface. Do not use chrome polish on aluminum wheels.

5-118

If you drive your vehicle through an

Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on chrome wheels only. Use chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application. Notice: automatic car wash that has silicone carbide tire cleaning brushes, you could damage the aluminum or chrome-plated wheels. The repairs would not be covered by your warranty. Never drive a vehicle equipped with aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes. Do not take your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes. These brushes can also damage the surface of these wheels.

Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.

Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.

5-119

Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, GM will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.

Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your GM dealer. Larger areas of finish damage can be corrected in your GM dealer’s body and paint shop.

Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your dealer or an underbody car washing system can do this for you.

5-120

Vehicle Care/Appearance Materials

Description

Usage

Description

Polishing Cloth Wax-Treated Tar and Road Oil Remover Chrome Cleaner and Polish White Sidewall Tire Cleaner Vinyl Cleaner

Glass Cleaner

Chrome and Wire Wheel Cleaner

Finish Enhancer

Usage

Interior and exterior polishing cloth. Removes tar, road oil, and asphalt. Use on chrome or stainless steel. Removes soil and black marks from whitewalls. Cleans vinyl. Removes dirt, grime, smoke and fingerprints. Removes dirt and grime from chrome wheels and wire wheel covers. Removes dust, fingerprints, and surface contaminants. Spray on and wipe off.

Swirl Remover Polish

Cleaner Wax

Foaming Tire Shine Low Gloss

Wash Wax Concentrate

Spot Lifter

Odor Eliminator

Removes swirl marks, fine scratches, and other light surface contamination. Removes light scratches and protects finish. Cleans, shines, and protects in one step. No wiping necessary. Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free. Quickly removes spots and stains from carpets, vinyl, and cloth upholstery. Odorless spray odor eliminator used on fabrics, vinyl, leather and carpet.

5-121

Vehicle Identification

Vehicle Identification Number (VIN)

This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration.

Engine Identification The eighth character in the VIN is the engine code. This code will help you identify your vehicle’s engine, specifications, and replacement parts.

Service Parts Identification Label You will find this label on the inside of the glove box. It is very helpful if you ever need to order parts. On this label, you will find the following: (cid:127) VIN (cid:127) Model designation (cid:127) Paint information (cid:127) Production options and special equipment Be sure that this label is not removed from the vehicle.

5-122

Electrical System

Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Your vehicle has an airbag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Airbag-Equipped Vehicle on page 1-86.

Windshield Wiper Fuses The windshield wiper motor is protected by an internal circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem and not snow, etc., be sure to get it fixed.

Power Windows and Other Power Options Circuit breakers protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed or goes away.

Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating. If you ever have a problem on the road and don’t have a spare fuse, you can borrow one that has the same amperage. Just pick some feature of your vehicle that you can get along without – like the radio or cigarette lighter – and use its fuse, if it is the correct amperage. Replace it as soon as you can.

5-123

Instrument Panel Fuse Block

The fuse block access door is on the driver’s side edge of the instrument panel. Pull off the cover to access the fuse block.

To remove fuses, hold the end of the fuse between your thumb and index finger and pull straight out. You may have spare fuses located behind the fuse block access door. These can be used to replace a bad fuse. However, make sure it is of the correct amperage.

Fuses

RR WPR

SEO ACCY

WS WPR

TBC ACCY

Usage

Not Used

Special Equipment Option Accessory

Windshield Wipers

Truck Body Controller Accessory

5-124

Fuses

Usage

Fuses

Usage

IGN 3

4WD

HTR A/C

LOCK (Relay)

HVAC 1

LT DR

CRUISE

UNLCK (Relay)

RR FOG LP

BRAKE

Ignition, Heated Seats

Four-Wheel Drive System, Auxiliary Battery

Climate Control System

Power Door Lock Relay (Lock Function)

Climate Control System

Driver’s Door Harness Connection

Cruise Control, Power Take Off (PTO)

Power Door Lock Relay (Unlock Function)

Not Used

DRIVER UNLCK

IGN 0

TBC IGN 0

VEH CHMSL

Power Door Lock Relay (Driver’s Door Unlock Function)

TCM

Truck Body Controller

Vehicle and Trailer High Mounted Stoplamp

LT TRLR ST/TRN

Left Turn Signal/Stop Trailer

LT TRN

VEH STOP

Left Turn Signals and Sidemarkers

Vehicle Stoplamps, Brake Module, Electronic Throttle Control Module

RT TRLR ST/TRN

Right Turn Signal/Stop Trailer

Anti-Lock Brake System

RT TRN

Right Turn Signals and Sidemarkers

5-125

Center Instrument Panel Fuse Block The center instrument panel utility block is located underneath the instrument panel, to the left of the steering column.

Device

Usage

SEO

TRAILER

UPFIT

Special Equipment Option

Trailer Brake Wiring

Upfitter (Not Used)

Fuses

Usage

BODY

DDM

Harness Connector

Driver Door Module

AUX PWR 2, M/GATE Not Used

LCKS

ECC, TPM

TBC 2C

HAZRD

CB LT DRS

TBC 2B

TBC 2A

Power Door Lock System

Tire Pressure Monitoring System

Truck Body Controller

Flasher Module

Left Power Windows Circuit Breaker

Truck Body Controller

Truck Body Controller

5-126

Device

Usage

Underhood Fuse Block

SL RIDE

HDLR 2

BODY

DEFOG

HDLNR 1

Ride Control Harness Connection

Headliner Wiring Connector

Body Wiring Connector

Rear Defogger Relay

Headliner Wiring Connector 1

SPARE RELAY

Not Used

CB SEAT

CB RT DOOR

SPARE

INFO

Driver and Passenger Seat Module Circuit Breaker

Right Power Windows Circuit Breaker

Not Used

Infotainment Harness Connection

The underhood fuse block in the engine compartment on the driver’s side of the vehicle near the battery. Lift the cover for access to the fuse/relay block. To remove fuses hold the end of the fuse between your thumb and index finger and pull straight out. See Engine Compartment Overview on page 5-14 for more information on its location.

5-127

5-128

*1 Fuel Injection Rail #2-Gasoline Engine; Engine

Control Module-Diesel Engine.

*2 Fuel Injection Rail #1-Gasoline Engine;

Actuator-Diesel Engine.

*3 Oxygen Sensors-Gasoline Engine; Fuel Heater-Diesel

Engine.

*4 Oxygen Sensors-Gasoline Engine; Engine Control

Module 1-Diesel Engine.

*5 Ignition 1-Gasoline Engine; Engine Control

Module-Diesel Engine.

*6 Powertrain Control Module B-Gasoline Engine;

Engine Control Module B-Diesel Engine.

*7 Rear Climate Control. *8 Sunroof.

Fuses

Usage

GLOW PLUG

CUST FEED HYBRID

STUD #1

Diesel Glow Plugs and Intake Air Heater Gasoline Accessory Power Hybrid Auxiliary Power (Single Battery and Diesels Only)/ Dual Battery (TP2) Do not install fuse.

Fuses

Usage

MBEC

BLWR

LBEC

STUD #2*

ABS VSES/ECAS IGN A IGN B

LBEC 1

TRL PARK

RR PARK

Mid Bussed Electrical Center Power Feed, Front Seats, Right Doors Front Climate Control Fan Left Bussed Electrical Center, Door Modules, Door Locks, Auxiliary Power Outlet—Rear Cargo Area and Instrument Panel Accessory Power/Trailer Wiring Brake Feed Anti-lock Brakes Vehicle Stability Ignition Power Ignition Power Left Bussed Electrical Center, Left Doors, Truck Body Controller, Flasher Module Parking Lamps Trailer Wiring Right Rear Parking and Sidemarker Lamps

5-129

Fuses

Usage

Fuses

Usage

Left Rear Parking and Sidemarker Lamps Parking Lamps Relay Starter Relay Interior Lamps Stoplamps Truck Body Controller Battery Feed Off-Road Lamps Not Used Auxiliary Power Outlet — Console Powertrain Control Module Electronic Throttle Control, Electronic Brake Controller-Gasoline Engine, Fan Clutch-Diesel Engines Instrument Panel Cluster, Air Conditioning Relay, Turn Signal/Hazard Switch, Starter Relay

RTD TRL B/U F/PMP

B/U LP

RR DEFOG HDLP-HI PRIME

AIRBAG

FRT PARK

DRL

SEO IGN TBC IGN1
HI HDLP-LT LH HID

Ride Control Backup Lamps Trailer Wiring Fuel Pump (Relay) Back-up Lamps, Automatic Transmission Shift Lock Control System Rear Window Defogger Headlamp High Beam Relay Not Used Supplemental Inflatable Restraint System Front Parking Lamps, Sidemarker Lamps Daytime Running Lamps (Relay) Rear Defog Relay Truck Body Controller Ignition High Beam Headlamp-Left Not Used

LR PARK

PARK LP STRTR INTPARK STOP LP

TBC BATT

SEO B2
4WS

AUX PWR

PCM 1

ETC/ECM

IGN E

5-130

Fuses

Usage

Fuses

Usage

DRL RVC

IPC/DIC

HVAC/ECAS CIG LTR HI HDLP-RT HDLP-LOW

A/C COMP

A/C COMP TCMB RR WPR RADIO

SEO B1

LO HDLP-LT

Daytime Running Lamps Regulated Voltage Control Instrument Panel Cluster/Driver Information Center Climate Control Controller Cigarette Lighter High Beam Headlamp-Right Headlamp Low Beam Relay Air Conditioning Compressor Relay Air Conditioning Compressor Transmission Control Module Not Used Audio System Mid Bussed Electrical Center, Rear Heated Seats, Universal Home Remote System Headlamp Low Beam-Left

BTSI

CRNK LO HDLP-RT FOG LP FOG LP HORN

W/S WASH

W/S WASH

INFO

RADIO AMP RH HID HORN EAP TREC SBA

Brake Transmission Shift Interlock System Starting System Headlamp Low Beam-Right Fog Lamps Relay Fog Lamps Horn Relay Windshield Washer Pump Relay Windshield Washer Pump OnStar®/Rear Seat Entertainment Radio Amplifier Not Used Horn Not Used Not Used Supplemental Brake Assist

5-131

Auxiliary Electric Cooling Fan Fuse Block

The auxiliary electric cooling fan fuse block is located in the engine compartment on the driver’s side of the vehicle next to the underhood fuse block.

Lift the cover for access to the fuse/relay block.

Fuses

COOL/FAN

COOL/FAN

COOL/FAN

Usage

Cooling Fan

Cooling Fan Relay Fuse

Cooling Fan Fuse

Relays

Usage

COOL/FAN 1

Cooling Fan Relay 1

COOL/FAN 3

Cooling Fan Relay 3

COOL/FAN 2

Cooling Fan Relay 2

5-132

Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants (Gasoline Engine) on page 6-14 for more information.

Application

Cooling System

4.3L V6 Automatic with Front A/C* 4.3L V6 Automatic with Front A/C** 4.3L V6 Manual with Front A/C* 4.3L V6 Manual with Front A/C** 4.8L V8 Automatic with Front A/C* 4.8L V8 Automatic with Front A/C** 4.8L V8 Manual with Front A/C* 4.8L V8 Manual with Front A/C** 5.3L V8 Automatic with Front A/C* 5.3L V8 Automatic with Front A/C** 6.0L V8 Automatic* 6.0L V8 Automatic** 6.0L V8 Manual*

Capacities

English

14.8 qt 16.5 qt 15.1 qt 16.6 qt 15.2 qt 16.8 qt 15.5 qt 17.0 qt 15.2 qt 16.8 qt 16.2 qt 16.7 qt 16.7 qt

Metric

14.0 L 15.6 L 14.3 L 15.7 L 14.4 L 15.9 L 14.7 L 16.1 L 14.4 L 15.9 L 15.3 L 15.8 L 15.8 L

5-133

Application

8.1L V8 HD Automatic* 8.1L V8 Automatic* 8.1 V8 Manual*

* Engine Fan Driven cooling system ** Electric Cooling Fan system Engine Oil with Filter

4.3 V6
4.8 V8; 5.3 V8; 6.0 V8
8.1 V8
Fuel Tank

Short Bed and 2500 LD Long Bed and Chassis Cab (Pickup Box Delete) Chassis Cab 3500 and 3500HD — front Chassis Cab 3500 and 3500HD — rear

Capacities

English 25.0 qt 26.9 qt 27.1 qt

4.5 qt 6.0 qt 6.5 qt

Metric 23.7 L 25.5 L 25.6 L

4.3 L 5.7 L 6.1 L

26.0 gal 34.0 gal 27.0 gal 23.0 gal 2.0 qt 140 ft lb

98.0 L 128.7 L 102.0 L 87.0 L 1.9 L

Transfer Case Fluid Wheel Nut Torque After refill, the level must be rechecked. Add enough engine coolant so that the fluid is within the proper operating range.

190 Y

5-134

Engine

VIN Code

Transmission

Spark Plug Gap

Engine Specifications

VORTEC™ 4.3L V6

VORTEC™ 4.8L V8

VORTEC™ 5.3L V8
VORTEC™ 5.3L V8

VORTEC™ 6.0 V8

VORTEC™ 6.0L V8

VORTEC™ 8.1L V8

Automatic

Manual

Automatic

Manual

Automatic Automatic Automatic

Manual

Automatic

Manual

Automatic

Manual

0.060 inches (1.52 mm)

0.040 inches (1.01 mm)

0.040 inches (1.01 mm) 0.040 inches (1.01 mm)

0.040 inches (1.01 mm)

0.040 inches (1.01 mm)

0.060 inches (1.52 mm)

5-135

✍ NOTES

5-136

Section 6

Maintenance Schedule

Maintenance Schedule ......................................6-2
Introduction ...................................................6-2
Maintenance Requirements ..............................6-2
Your Vehicle and the Environment ....................6-2
Using the Maintenance Schedule ......................6-3
Scheduled Maintenance

(Gasoline Engine) .......................................6-4

Additional Required Services

(Gasoline Engine) .......................................6-7

Maintenance Footnotes

(Gasoline Engine) .......................................6-9
Owner Checks and Services ..........................6-11

At the First 100, 1,000 and 6,000 Miles

(160, 1 600 and 10 000 km) .......................6-11
At Each Fuel Fill ..........................................6-11
At Least Once a Month .................................6-12
At Least Once a Year ...................................6-12
Recommended Fluids and Lubricants

(Gasoline Engine) ......................................6-14

Normal Maintenance Replacement Parts

(Gasoline Engines) ....................................6-18
Engine Drive Belt Routing ..............................6-19
Maintenance Record .....................................6-20

6-1

Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance may not be covered by warranty.

Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance is important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, be sure to maintain your vehicle properly.

Maintenance Schedule

Introduction This maintenance section applies to vehicles with a gasoline engine. If your vehicle has a diesel engine, see the maintenance schedule section in the DURAMAX® Diesel Engine Supplement. Important: Keep engine oil at the proper level and change as recommended.

Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details.

6-2

Using the Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands, or in many other ways. Because of all the different ways people use their vehicles, maintenance needs vary. You may need more frequent checks and replacements. So please read the following and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your GM Goodwrench® dealer. This schedule is for vehicles that:

carry passengers and cargo within recommended limits. You will find these limits on the tire and loading information label. See Loading Your Vehicle on page 4-48. are driven on reasonable road surfaces within legal driving limits. are driven off-road in the recommended manner. See Off-Road Driving on page 4-16. use the recommended fuel. See Gasoline Octane on page 5-6.

The services in Scheduled Maintenance (Gasoline Engine) on page 6-4 should be performed when indicated. See Additional Required Services (Gasoline Engine) on page 6-7 and Maintenance Footnotes (Gasoline Engine) on page 6-9 for further information.

{CAUTION:

Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, see your GM Goodwrench® dealer to have a qualified technician do the work. See Doing Your Own Service Work on page 5-5.

Some maintenance services can be complex. So, unless you are technically qualified and have the necessary equipment, you should have your GM Goodwrench® dealer do these jobs. When you go to your GM Goodwrench® dealer for your service needs, you will know that GM-trained and supported service technicians will perform the work using genuine GM parts.

6-3

(cid:127) (cid:127) (cid:127) (cid:127) If you want to purchase service information, see Service Publications Ordering Information on page 7-15. Owner Checks and Services on page 6-11 tells you what should be checked, when to check it, and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants (Gasoline Engine) on page 6-14 and Normal Maintenance Replacement Parts (Gasoline Engines) on page 6-18. When your vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. We recommend the use of genuine GM parts.

Scheduled Maintenance (Gasoline Engine) This maintenance section applies to vehicles with a gasoline engine. If your vehicle has a diesel engine, see the maintenance schedule section in the DURAMAX® Diesel Engine Supplement. When the CHANGE ENGINE OIL message comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year. However, your engine oil and filter must be changed

6-4

at least once a year and at this time the system must be reset. Your GM Goodwrench® dealer has GM-trained service technicians who will perform this work using genuine GM parts and reset the system. If the engine oil life system is ever reset accidentally, you must service your vehicle within 3,000 miles (5 000 km) since your last service. Remember to reset the oil life system whenever the oil is changed. See Engine Oil Life System (Gasoline Engine) on page 5-23 for information on the Engine Oil Life System and resetting the system. When the CHANGE ENGINE OIL message appears, certain services, checks, and inspections are required. Required services are described in the following for “Maintenance I” and “Maintenance II.” Generally, it is recommended that your first service be Maintenance I, your second service be Maintenance II, and that you alternate Maintenance I and Maintenance II thereafter. However, in some cases, Maintenance II may be required more often. Maintenance I — Use Maintenance I if the CHANGE ENGINE OIL message comes on within 10 months since the vehicle was purchased or Maintenance II was performed. Maintenance II — Use Maintenance II if the previous service performed was Maintenance I. Always use Maintenance II whenever the message comes on 10 months or more since the last service or if the message has not come on at all for one year.

Scheduled Maintenance

Service

Maintenance I Maintenance II

Change engine oil and filter. See Engine Oil (Gasoline Engine) on page 5-20. Reset oil life system. See Engine Oil Life System (Gasoline Engine) on page 5-23. An Emission Control Service. Allison Transmission® only: Replace external control-main filter only at the first maintenance service performed on the vehicle. Lubricate chassis components. See footnote #. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner filter or change indicator (if equipped). If necessary, replace filter. See Engine Air Cleaner/Filter (Gasoline Engines) on page 5-25. See footnote (p). Rotate tires and check inflation pressures and wear. See Tire Inspection and Rotation on page 5-81 and “Tire Wear Inspection” in At Least Once a Month on page 6-12. Inspect brake system. See footnote (a). Check engine coolant and windshield washer fluid levels and add fluid as needed.

•

• •

•

•

•

•

• •

•

•

•

•

6-5

Scheduled Maintenance (cont’d) Service

Maintenance I Maintenance II

Perform any needed additional services. See “Additional Required Services” in this section. Inspect suspension and steering components. See footnote (b). Inspect engine cooling system. See footnote (c). Inspect wiper blades. See footnote (d). Inspect restraint system components. See footnote (e). Lubricate body components. See footnote (f). Check transmission fluid level and add fluid as needed. Inspect shields, vehicles with diesel engine or with GVWR above 10,000 lbs (4 536 kg) only. See footnote (n).

•

•

• • • • • •

•

6-6

Additional Required Services (Gasoline Engine) This maintenance section applies to vehicles with a gasoline engine. If your vehicle has a diesel engine, see the maintenance schedule section in the DURAMAX® Diesel Engine Supplement. The following services should be performed at the first maintenance service (I or II) after the indicated miles (kilometers) shown for each item.

Additional Required Services 75,000

25,000
(41 500)

50,000
(83 000)

(125 000)

100,000
(166 000)

125,000
(207 500)

150,000
(240 000)

Service and Miles (Kilometers)

Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components. Vehicles without a filter restriction indicator: Replace engine air cleaner filter. See Engine Air Cleaner/Filter (Gasoline Engines) on page 5-25. 6-speed manual transmission only: Change clutch fluid. See footnote (l). Allison Transmission® only: Change automatic transmission fluid and filter (severe service). See footnote (m). Allison Transmission® only: Change automatic transmission fluid and filter (normal service).

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

6-7

Additional Required Services (cont’d)

Service and Miles (Kilometers)

Except Allison Transmission®: Change automatic transmission fluid and filter (severe service). See footnote (h). Except Allison Transmission®: Change automatic transmission fluid and filter (normal service). Four-wheel drive with automatic transfer case only: Change transfer case fluid. See footnote (g). Inspect evaporative control system. An Emission Control Service. See footnotes † and (k). Replace spark plugs and inspect spark plug wires. An Emission Control Service. 5-speed manual transmission only: Change manual transmission fluid. Engine cooling system service (or every five years, whichever occurs first). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. See footnote (q).

6-8

25,000
(41 500)

50,000
(83 000)

75,000

(125 000)

100,000
(166 000)

125,000
(207 500)

150,000
(240 000)

•

•

•

•

•

•

•

•

•

•

•

•

•

•

Maintenance Footnotes (Gasoline Engine) This maintenance section applies to vehicles with a gasoline engine. If your vehicle has a diesel engine, see the maintenance schedule section in the DURAMAX® Diesel Engine Supplement. † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded. # Lubricate the front suspension, ball joints, steering linkage, transmission shift linkage, and parking brake cable guides. Ball joints should not be lubricated unless their temperature is 10°F (−12°C) or higher, or they could be damaged. Vehicles used under severe commercial operating conditions require lubrication on a regular basis every 3,000 miles (5 000 km). (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect drum brake linings/shoes for wear or cracks. Inspect other brake parts, including drums, wheel cylinders, calipers, parking brake, etc.

(b) Visually inspect front and rear suspension and steering system for damaged, loose or missing parts, signs of wear or lack of lubrication. Inspect power steering lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Visually check constant velocity joints, rubber boots, and axle seals for leaks. (c) Visually inspect hoses and have them replaced if they are cracked, swollen, or deteriorated. Inspect all pipes, fittings and clamps; replace with genuine GM parts as needed. To help ensure proper operation, a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year. (d) Visually inspect wiper blades for wear or cracking. Replace wiper blades that appear worn or damaged or that streak or miss areas of the windshield. (e) Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors, and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also look for any opened or broken airbag coverings, and have them repaired or replaced. The airbag system does not need regular maintenance.

6-9

(f) Lubricate all key lock cylinders, body door hinges, hood latch assembly, secondary latch, pivots, spring anchor, release pawl, tailgate hinges, tailgate linkage, tailgate handle pivot points, latch bolt, fuel door hinge, locks, and folding seat hardware. More frequent lubrication may be required when exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth will make them last longer, seal better and not stick or squeak. (g) Check vent hose at transfer case for kinks and proper installation. (h) Change automatic transmission fluid and filter if the vehicle Gross Vehicle Weight Rating (GVWR) is over 8600 lbs or if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside temperature

regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery

service.

(i) Drain, flush, and refill cooling system. This service can be complex; you should have your dealer perform this service. See Engine Coolant on page 5-35 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap, and filler neck. Pressure test the cooling system and pressure cap.

6-10

(j) A fluid loss in any vehicle system could indicate a problem. Have the system inspected and repaired and the fluid level checked. Add fluid if needed. (k) Inspect system. Check all fuel and vapor lines and hoses for proper hook-up, routing, and condition. Check that the purge valve works properly, if equipped. Replace as needed. (l) Change clutch fluid (or every 24 months, whichever occurs first). (m) Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:

− In heavy city traffic where the outside temperature

regularly reaches 90°F (32°C) or higher.

− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police, or delivery

service.

(n) Vehicles with diesel engine or with GVWR above 10,000 lbs (4 536 kg) only: Inspect shields for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable to vehicles sold in the United States and recommended for vehicles sold in Canada.

(p) If you drive regularly under dusty conditions, inspect the filter or change indicator (if equipped) at each engine oil change. (q) Visually inspect belt for fraying, excessive cracks, or obvious damage. Replace belt if necessary.

Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure the safety, dependability, and emission control performance of your vehicle. Your GM Goodwrench® dealer can assist you with these checks and services. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Recommended Fluids and Lubricants (Gasoline Engine) on page 6-14.

At the First 100, 1,000 and 6,000
Miles (160, 1 600 and 10 000 km) Check dual wheel nut torque. For proper torque, see Capacities and Specifications on page 5-133.

It is important to check your oil regularly

At Each Fuel Fill It is important to perform these underhood checks at each fuel fill. Engine Oil Level Check Check the engine oil level and add the proper oil if necessary. See Engine Oil (Gasoline Engine) on page 5-20 for further details. Notice: and keep it at the proper level. Failure to keep your engine oil at the proper level can cause damage to your engine not covered by your warranty. Engine Coolant Level Check Check the engine coolant level and add DEX-COOL® coolant mixture if necessary. See Engine Coolant on page 5-35 for further details. Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer fluid reservoir and add the proper fluid if necessary.

6-11

At Least Once a Month Tire Inflation Check Visually inspect your vehicle’s tires and make sure they are inflated to the correct pressures. Do not forget to check the spare tire. See Tires on page 5-72 for further details. Check to make sure the spare tire is stored securely. See Changing a Flat Tire on page 5-91. Tire Wear Inspection Tire rotation may be required for high mileage highway drivers prior to the Engine Oil Life System service notification. Check the tires for wear and, if necessary, rotate the tires. See Tire Inspection and Rotation on page 5-81.

At Least Once a Year Starter Switch Check

{CAUTION:

When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.

1. Before you start, be sure you have enough room

around the vehicle.

2. Firmly apply both the parking brake and the regular

brake. See Parking Brake on page 2-52. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.

3. Try to start the engine in each gear. The vehicle should start only in PARK (P) or NEUTRAL (N). If the vehicle starts in any other position, contact your GM Goodwrench® dealer for service.

6-12

Automatic Transmission Shift Lock Control System Check

{CAUTION:

When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.

1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.

2. Firmly apply the parking brake. See Parking Brake

on page 2-52. Be ready to apply the regular brake immediately if the vehicle begins to move.

3. With the engine off, turn the ignition to RUN, but do

not start the engine. Without applying the regular brake, try to move the shift lever out of PARK (P) with normal effort. If the shift lever moves out of PARK (P), contact your GM Goodwrench® dealer for service.

Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK in each shift lever position.

The ignition should turn to LOCK only when the shift lever is in PARK (P). The key should come out only in LOCK.

Contact your GM Goodwrench® dealer if service is required.

6-13

(cid:127) (cid:127) Parking Brake and Automatic Transmission Park (P) Mechanism Check

{CAUTION:

When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.

Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.

To check the parking brake’s holding ability: With the engine running and transmission in NEUTRAL (N), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only.

To check the PARK (P) mechanism’s holding ability: With the engine running, shift to PARK (P). Then release the parking brake followed by the regular brake.

Contact your GM Goodwrench® dealer if service is required. Underbody Flushing Service At least every spring, use plain water to flush any corrosive materials from the underbody. Take care to clean thoroughly any areas where mud and other debris can collect.

Recommended Fluids and Lubricants (Gasoline Engine) This maintenance section applies to vehicles with a gasoline engine. If your vehicle has a diesel engine, see the maintenance schedule section in the DURAMAX® Diesel Engine Supplement. Fluids and lubricants identified below by name, part number, or specification may be obtained from your dealer.

6-14

(cid:127) (cid:127) Usage

Engine Oil

Engine Coolant

Hydraulic Brake

System

Windshield

Washer Hydraulic

Clutch System

(5–Speed

Trans.) Hydraulic

Clutch System

(6–Speed

Trans.)

Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. GM Goodwrench® oil meets all the requirements for your vehicle. To determine the proper viscosity for your vehicle’s engine, see Engine Oil (Gasoline Engine) on page 5-20. 50/50 mixture of clean, drinkable water and use only DEX-COOL® coolant. See Engine Coolant on page 5-35. Delco® Supreme 11 Brake Fluid or equivalent DOT-3 brake fluid.

GM Optikleen® Washer Solvent.

Hydraulic Clutch Fluid (GM Part No. U.S. 12345347, in Canada 10953517) or equivalent DOT-3
brake fluid.

Hydraulic Clutch Fluid. Use only GM Part No. U.S. 88958860, in Canada 88901244, Super DOT-4 brake fluid.

Usage

Fluid/Lubricant

Power Steering

System

Manual

Transmission (5–Speed with

Low Gear, RPO MW3)

Manual

Transmission

(5–Speed

without

Low Gear, RPO MG5)

Manual

Transmission

(6–Speed)

Automatic

Transmission

Key Lock Cylinders

GM Power Steering Fluid (GM Part No. U.S. 89021184, in Canada 89021186). GM Goodwrench® Synthetic Manual Transmission Fluid (GM Part No. U.S. 12346190, in Canada 10953477) or equivalent SAE 75W-85 GL-4 gear oil.

Synchromesh Transmission Fluid (GM Part No. U.S. 12345349, in Canada 10953465).

Synthetic Transmission Fluid approved to Allison Transmission® specification TES-295 (GM Part No. U.S. 12378515, in Canada 88900701). DEXRON®-VI Automatic Transmission Fluid. Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474).

6-15

Usage

Fluid/Lubricant

Usage

Fluid/Lubricant

Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2
Category LB or GC-LB. Chassis Lubricant (GM Part No. U.S. 12377985, in Canada 88901242) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. SAE 80W-90 Axle Lubricant (GM Part No. U.S. 1052271, in Canada 10950849).

SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 12378261, in Canada 10953455) meeting GM Specification 9986115.

SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 12378261, in Canada 10953455) meeting GM Specification 9986115.

Manual

Transfer Case

Automatic

Transfer Case

DEXRON®-III Automatic Transmission Fluid. Look for “Approved for the H-Specification” on the label. AUTO-TRAK II Fluid (GM Part No. U.S. 12378508, in Canada 10953626).

Front Axle Propshaft Spline or One-Piece Propshaft

Spline

(Two-Wheel Drive with

Auto. Trans.)

Spline Lubricant, Special Lubricant (GM Part No. U.S. 12345879, in Canada 10953511) or lubricant meeting requirements of GM 9985830.

Rear Driveline Center Spline

Chassis Lubricant (GM Part No. U.S. 12377985, in Canada 88901242) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB.

Floor Shift Linkage

Chassis

Lubrication

Front Axle

(1500 Series)

Front Axle (1500 HD,

2500, 2500 HD,

and 3500
Series)

Rear Axle

6-16

Body Door Hinge Pins,

Tailgate Hinge and Linkage, Folding Seats, and Fuel Door

Hinge

Usage

Fluid/Lubricant

Usage

Fluid/Lubricant

Hood Hinges

Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474).

Tailgate Handle

Pivot Points, Hinges, Latch

Bolt, and Linkage

Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474).

Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474).

Weatherstrip Conditioning

Weatherstrip

Squeaks

Dielectric Silicone Grease (GM Part No. U.S. 12345579, in Canada 992887). Synthetic Grease with Teflon, Superlube (GM Part No. U.S. 12371287, in Canada 10953437).

6-17

Normal Maintenance Replacement Parts (Gasoline Engines) Replacement parts identified below by name, part number, or specification can be obtained from your GM dealer. If your vehicle has a diesel engine see the maintenance schedule section in the DURAMAX® Diesel Engine Supplement.

Part

GM Part Number

ACDelco® Part Number

Engine Air Cleaner/Filter

High Capacity Standard

Oil Filter

4.3L V6
4.8L V8; 5.3L V8; 6.0L V8
8.1L V8

Spark Plugs

4.3L V6
4.8L V8; 5.3L V8; 6.0L V8
8.1L V8

Wiper Blades (ITTA Type) 22 inches (56.0 cm) *A1518C high-capacity air cleaner filter may be substituted.

10368768
25311916*

25010792
88984215
25324052

89017883
12571164
12578277

15153642

A1518C A1519C*

PF47
PF46
PF454

41-932
41-985
41-983

—

6-18

Engine Drive Belt Routing

V6 Engines

V8 Engines

6-19

Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-11 can be added on the following record pages. You should retain all maintenance receipts.

Maintenance Record

Date

Odometer Reading

Serviced By

Maintenance I or Maintenance II

Services Performed

6-20

Date

Odometer Reading

Serviced By

Maintenance I or Maintenance II

Services Performed

Maintenance Record (cont’d)

6-21

Date

Odometer Reading

Serviced By

Maintenance I or Maintenance II

Services Performed

Maintenance Record (cont’d)

6-22

Section 7

Customer Assistance and Information

Customer Assistance and Information ...............7-2
Customer Satisfaction Procedure ......................7-2
Online Owner Center ......................................7-3
Customer Assistance for Text Telephone

(TTY) Users ...............................................7-4
Customer Assistance Offices ............................7-4
GM Mobility Reimbursement Program ................7-5
Roadside Assistance Program ..........................7-6
Courtesy Transportation ...................................7-7
Vehicle Data Collection and Event

Data Recorders ..........................................7-9
Collision Damage Repair ................................7-10

Reporting Safety Defects ................................7-13

Reporting Safety Defects to the

United States Government ..........................7-13

Reporting Safety Defects to the

Canadian Government ................................7-14

Reporting Safety Defects to

General Motors .........................................7-14
Service Publications Ordering Information .........7-15

7-1

Customer Assistance and Information

Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to GMC. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur. If your concern has not been resolved to your satisfaction, the following steps should be taken:

STEP ONE: Discuss your concern with a member of dealership management. Normally, concerns can be quickly resolved at that level. If the matter has already been reviewed with the sales, service or parts manager, contact the owner of the dealership or the general manager.

STEP TWO: If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, contact the GMC Consumer Relations Manager by calling 1-800-GMC-8782 (1-800-462-8782, Customer Assistance prompt). In Canada, contact GM of Canada Customer Communication by calling 1-800-263-3777 (English) or 1-800-263-7854 (French).

7-2

We encourage you to call the toll-free number in order to give your inquiry prompt attention. Please have the following information available to give the Customer Assistance Representative: (cid:127) Vehicle Identification Number (VIN). This is available from the vehicle registration or title, or the plate at the top left of the instrument panel and visible through the windshield.

(cid:127) Dealership name and location. (cid:127) Vehicle delivery date and present mileage. When contacting GMC, please remember that your concern will likely be resolved at a dealer’s facility. That is why we suggest you follow Step One first if you have a concern.

STEP THREE: Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However, if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two, you should file with the BBB Auto Line Program to enforce any additional rights you may have. Canadian owners refer to your Warranty and Owner Assistance Information booklet for information on the Canadian Motor Vehicle Arbitration Plan (CAMVAP).

The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty.

Although you may be required to resort to this informal dispute resolution program prior to filling out a court action, use of the program is free of charge and your case will generally be heard within 40 days. If you do not agree with the decision given in your case, you may reject it and proceed with any other venue for relief available to you.

You may contact the BBB Auto Line Program using the toll-free telephone number or write them at the following address:

BBB Auto Line Program Council of Better Business Bureaus, Inc. 4200 Wilson Boulevard Suite 800
Arlington, VA 22203-1838
Telephone: 1-800-955-5100

This program is available in all 50 states and the District of Columbia. Eligibility is limited by vehicle age, mileage, and other factors. General Motors reserves the right to change eligibility limitations and/or discontinue its participation in this program.

Online Owner Center The Owner Center is a resource for your GM ownership needs. Specific vehicle information can be found in one place. The Online Owner Center allows you to: (cid:127) Get e-mail service reminders. (cid:127) Access information about your specific vehicle,

including tips and videos and an electronic version of this owner’s manual (United States only).

(cid:127) Keep track of your vehicle’s service history and

maintenance schedule. Find GM dealers for service nationwide.

(cid:127) Receive special promotions and privileges only

available to members (United States only).

Refer to the web for updated information. To register your vehicle, visit www.MyGMLink.com (United States) or My GM Canada within www.gmcanada.com (Canada).

7-3

(cid:127) From Puerto Rico

1-800-496-9992 (English) 1-800-496-9993 (Spanish) Fax Number: 313-381-0022

U.S. Virgin Islands: 1-800-496-9994
Fax Number: 313-381-0022

Canada

General Motors of Canada Limited Customer Communication Centre, 163-005
1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7
1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-268-6800

All Overseas Locations Please contact the local General Motors Business Unit.

Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use the Text Telephones (TTYs), GMC has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with GMC by dialing: 1-800-GMC-8583 (462-8583). (TTY users in Canada can dial 1-800-263-3830.)

Customer Assistance Offices GMC encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail GMC, refer to the addresses below. United States

GMC Customer Assistance Center P.O. Box 33172
Detroit, MI 48232-5172
www.GMC.com 1-800-GMC-8782 (462-8782) 1-800-GMC-8583 (462-8583) (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-GMC-8782 (462-8782) Fax Number: 313-381-0022

7-4

Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands)

GM Mobility Reimbursement Program

General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740
Col. Lomas de Bezares C.P. 11910, Mexico, D.F. 01-800-508-0000
Long Distance: 011-52-53 29 0 800

This program, available to qualified applicants, can reimburse you up to $1,000 of the cost of eligible aftermarket adaptive equipment required for your vehicle, such as hand controls or a wheelchair/scooter lift. The offer is available for a very limited period of time from the date of vehicle purchase/lease. For more details, or to determine your vehicle’s eligibility, visit gmmobility.com or call the GM Mobility Assistance Center at 1-800-323-9935. Text telephone (TTY) users, call 1-800-833-9935. GM of Canada also has a Mobility Program. Call 1-800-GM-DRIVE (463-7483) for details. TTY users call 1-800-263-3830.

7-5

Flat Tire Change: Installation of a spare tire will be covered at no charge. The customer is responsible for the repair or replacement of the tire if not covered by a warrantable failure. Jump Start: No-start occurrences which require a battery jump start will be covered at no charge.

(cid:127) Dealer Locator Service

Trip Routing: Your Roadside Assistance Representative can provide you with specific information regarding this feature. Trip Interruption Expense Benefits: Your Roadside Assistance Representative can provide you with specific information regarding this feature.