2008 GMC Acadia Owners Manual

Download PDF Manual
1-888-4-ONSTAR (1-888-466-7827). OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar Owner’s Guide for more information (Only available in the continental U.S.). OnStar Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-128 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” to activate the OnStar Hands-Free Calling. On some vehicles, the mute button can be used to dial numbers into voicemail systems, or to dial phone extensions. See the OnStar Owner’s Guide for more information. How OnStar Service Works Your vehicle’s OnStar system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar Call Center at the time of an OnStar button press, Emergency button press or if your airbags or AACN system deploys. The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar Hands-Free Calling, your vehicle also sends OnStar your GPS location so that we can provide you with location-based services. 2-49 OnStar service cannot work unless your vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless you are in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. Location information about your vehicle is only available if the GPS satellite signals are unobstructed and available. Your vehicle must have a working electrical system (including adequate battery power) for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility Increase the radio volume if you cannot hear the OnStar advisor. If the light next to the OnStar buttons is red, this means that your system is not functioning properly and should be checked by your dealer/retailer. If the light appears clear (no light is appearing), your OnStar subscription has expired. You can always press the OnStar button to conﬁrm that your OnStar equipment is active. 2-50 Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Universal Home Remote System Operation (With One Triangular LED) If there is one triangular Light Emitting Diode (LED) indicator light above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming the Universal Home Remote. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section. When programming a garage door, park outside of the garage. Park directly in line with and facing the garage door opener motor-head or gate motor-head. Be sure that people and objects are clear of the garage door or gate you are programming. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Programming the Universal Home Remote System If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. 2-51 To program up to three devices: 1. From inside the vehicle, press and hold down the two outside buttons at the same time, releasing only when the Universal Home Remote indicator light begins to ﬂash, after 20 seconds. This step will erase the factory settings or all previously programmed buttons. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program the remaining two Universal Home Remote buttons. 2. Hold the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. The hand-held transmitter was supplied by the manufacturer of your garage door opener receiver (motor head unit). 3. At the same time, press and hold both the Universal Home Remote button that you would like to use to control the garage door and the hand-held 2-52 transmitter button. Do not release the Universal Home Remote button or the hand-held transmitter button until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 4. The indicator light on the Universal Home Remote will ﬂash slowly at ﬁrst and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on continuously, the programming is complete and your garage door should move when the Universal Home Remote button is pressed and released. You do not need to continue the programming Steps 6 through 8 and can stop here. If the Universal Home Remote indicator light blinks rapidly for two seconds and then turns to a constant light, continue with the programming Steps 6 through 8. It may be helpful to have another person available to assist with the remaining steps. 8. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, chosen in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it. Again, if the door does not move, press and hold the same button a third time for two seconds, and then release. The Universal Home Remote should now activate the garage door. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming the Universal Home Remote System.” Do not repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. 2-53 6. After Steps 1 through 5 have been completed, locate inside the garage the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. 7. Firmly press and release the “Learn” or “Smart” button. After you press this button, you will have 30 seconds to complete Step 8. Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. 2-54 Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons Erase the programmed buttons when you sell or terminate your lease. To erase all programmed buttons on the Universal Home Remote device: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. 2. Release both buttons. Reprogramming a Single Universal Home Remote Button To reprogram any of the three Universal Home Remote buttons, repeat the programming instructions earlier in this section, beginning with Step 2. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 7-5. Storage Areas Glove Box To open, lift the handle up. Use the key to lock and unlock. Cupholder(s) There are two cupholders, with removable liners, located in front of the center console. There are cupholders located in the second row seat armrest. To access, pull the armrest down. There are additional cupholders located on each side of the third row seat and in each door. There are cupholders located behind the center console. To access, pull down on the handle. Instrument Panel Storage Your vehicle has an instrument panel storage area located above the radio. To open the cover, press the button. 2-55 Center Console Storage Second Row Center Console The armrest on the center console can slide forwards and backwards by holding up the lever located on the front of it. To open the armrest storage area, press the button located on the front of the armrest. There is additional storage under the armrest. Move the armrest all the way to the rear position. The tray can be removed for additional storage. Your vehicle may have a second row center console. 2-56 To access the upper storage area, press the upper button (2) and lift up. To access the lower storage area, press the lower button (3) and lift up. The top of the console can be folded forward for increased storage area. Lift up on handle on the rear of the console (1) and pull forward. {CAUTION: Never open more than one of the three latches at a time. This is to help avoid personal injury and damage to the console. Notice: Slide the front console as far forward as it will go before folding the second row console forward. This will help prevent damage to the consoles. Floor Mats There is a grommet in the driver side ﬂoor mat that attaches to a hook on the ﬂoor of the vehicle to hold the ﬂoor mat in place. To remove the ﬂoor mat, pull the mat towards the rear of the vehicle until the grommet can be removed from the hook. 2-57 Luggage Carrier {CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along. This can cause you to lose control. What you are carrying could be violently torn off, and this could cause you or other drivers to have a collision, and of course damage your vehicle. You may be able to carry something like this inside. But, never carry something longer or wider than the luggage carrier on top of your vehicle. If you have the luggage carrier, you can load things on top of your vehicle. Crossrails are not standard on this vehicle and must be purchased at your dealer/retailer. Notice: Loading cargo on the luggage carrier that weighs more than 200 lbs (91 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests as far forward as possible and against the side rails, making sure to fasten it securely. 2-58 Do not exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-21. To prevent damage or loss of cargo as you are driving, check to make sure the cargo is still securely fastened. Rear Seat Armrest Your vehicle may have a rear seat armrest that contains two cupholders. To access the cupholders, pull the armrest down from the rear seatback. Convenience Net Your vehicle may have a convenience net in the rear of the vehicle. Store small loads as far forward as possible. The net should not be used to store heavy loads. Cargo Cover Your vehicle may have a cargo cover. It can be used to cover items in the rear of the vehicle. To install the cover, place the loops on each corner of the cover on the four hooks in the rear of the vehicle. The cover should be stored securely when not in use. Cargo Tie Downs Cargo tie-downs located in the rear of the vehicle are used to secure small loads. Cargo Management System Your vehicle has a cargo management system located in the rear of the vehicle. To open, pull the handle toward the rear of the vehicle and lift the cover up. To remove the cargo management system: 1. Open the lid. 2. Remove the side panels and place inside the bin. 3. Loosen the retaining nuts on each side of the system by turning them counterclockwise. 4. Close the lid. 5. Pull up on the system by using the built in handles and remove it from the vehicle. There is an additional storage compartment on each side of the system. To open, unlatch and lift the panel up. 2-59 Sunroof The vehicle may have a sunroof over the front seats, and a rear sunroof over the second row seats. The rear sunroof does not open. The switches to operate the front sunroof and rear sunshade are located on the headliner above the rearview mirror. The ignition must be in ON or ACCESSORY to operate the sunroof. See Ignition Positions on page 2-26. Express-open/Express-close: From the closed position, press and release the rear of the driver’s side switch to express-open the sunroof. Press and release the front of the driver’s side switch to express-close the sunroof. The front sunshade must be opened and closed manually. Push up on the sunshade handle to open the sunshade. Notice: The rear sunshade could be damaged if you attempt to open or close it manually. Do not manually open or close the rear sunshade. To open the rear sunshade, located over the second row seats, press and release the rear of the passenger’s side switch. Press and release the front of the switch to close the sunshade. Vent: From the closed position, press and hold the front of the driver’s side switch to vent the sunroof. Press and hold the rear of the driver’s side switch to close the sunroof. 2-60 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt and Telescopic Steering Wheel ...................3-6 Power Tilt Wheel and Telescopic Steering Column ......................................................3-7 Turn Signal/Multifunction Lever .........................3-8 Turn and Lane-Change Signals ........................3-8 Headlamp High/Low-Beam Changer ..................3-9 Flash-to-Pass .................................................3-9 Windshield Wipers ..........................................3-9 Windshield Washer .......................................3-10 Rear Window Wiper/Washer ...........................3-11 Cruise Control ..............................................3-12 Exterior Lamps .............................................3-14 Delayed Headlamps ......................................3-15 Daytime Running Lamps (DRL)/ Automatic Headlamp System .......................3-16 Fog Lamps ..................................................3-16 Instrument Panel Brightness ...........................3-17 Courtesy Lamps ...........................................3-17 Dome Lamps ...............................................3-17 Dome Lamp Override ....................................3-17 Entry Lighting ...............................................3-17 Delayed Entry Lighting ...................................3-18 Delayed Exit Lighting .....................................3-18 Parade Dimming ...........................................3-18 Reading Lamps ............................................3-19 Electric Power Management ...........................3-19 Battery Run-Down Protection ..........................3-20 Head-Up Display (HUD) .................................3-20 Accessory Power Outlet(s) .............................3-24 Power Outlet 115 Volt Alternating Current ........3-25 Climate Controls ............................................3-26 Climate Control System .................................3-26 Dual Automatic Climate Control System ...........3-29 Outlet Adjustment .........................................3-36 Rear Air Conditioning and Heating System .........................................3-36 Rear Air Conditioning and Heating System and Electronic Climate Controls .........................3-38 Warning Lights, Gages, and Indicators .............................................3-39 Instrument Panel Cluster ................................3-40 Speedometer and Odometer ...........................3-41 Tachometer .................................................3-41 Safety Belt Reminders ...................................3-41 Airbag Readiness Light ..................................3-42 Passenger Airbag Status Indicator ...................3-43 Charging System Light ..................................3-45 Voltmeter Gage ............................................3-46 Brake System Warning Light ..........................3-47 3-1 Section 3 Instrument Panel Antilock Brake System Warning Light ...........................................3-48 StabiliTrak® Indicator Light ..............................3-48 Engine Coolant Temperature Warning Light ......3-49 Engine Coolant Temperature Gage ..................3-49 Tire Pressure Light .......................................3-50 Malfunction Indicator Lamp .............................3-50 Oil Pressure Light .........................................3-54 Security Light ...............................................3-54 Fog Lamp Light ............................................3-55 Cruise Control Light ......................................3-55 Highbeam On Light .......................................3-55 Tow/Haul Mode Light ....................................3-55 Fuel Gage ...................................................3-56 Driver Information Center (DIC) .......................3-57 DIC Operation and Displays (With DIC Buttons) ....................................3-57 DIC Operation and Displays (Without DIC Buttons) ...................................................3-63 DIC Warnings and Messages .........................3-66 DIC Vehicle Customization (With DIC Buttons) ....3-75 Audio System(s) .............................................3-84 Setting the Time ...........................................3-85 Radio(s) (MP3) .............................................3-87 Using an MP3 (Radio with CD and Six-Disc CD Player) .............................................3-104 Using an MP3 (Radio with CD and DVD Player) ...................................................3-108 XM Radio Messages ...................................3-113 Navigation/Radio System ..............................3-115 Rear Seat Entertainment (RSE) System .........3-115 Rear Seat Audio (RSA) ................................3-125 Rear Audio Controller (RAC) .........................3-127 Theft-Deterrent Feature ................................3-127 Audio Steering Wheel Controls ......................3-128 Radio Reception .........................................3-129 Multi-Band Antenna .....................................3-129 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of your instrument panel are listed here: A. Air Vent. See Outlet Adjustment on page 3-36. B. Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-8. Windshield Wipers. See Turn Signal/Multifunction Lever on page 3-8. C. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-40. D. Head-Up Display (HUD) Buttons. See Head-Up Display (HUD) on page 3-20. E. Audio System. See Audio System(s) on page 3-84. Navigation/Radio System (If Equipped). See Navigation/Radio System on page 3-115. F. Exterior Lamps Control. See Exterior Lamps on page 3-14. G. Hood Release. See Hood Release on page 5-13. H. Dome Lamp Override Button. See Dome Lamp Override on page 3-17. Instrument Panel Brightness Control. See Instrument Panel Brightness on page 3-17. I. Cruise Control Buttons. See Cruise Control on page 3-12. J. Tilt and Telescopic Steering Wheel. See Tilt and Telescopic Steering Wheel on page 3-6. Power Tilt Wheel and Telescopic Steering (If Equipped). See Power Tilt Wheel and Telescopic Steering Column on page 3-7. K. Horn. See Horn on page 3-6. L. Audio Steering Wheel Control Buttons. See Audio Steering Wheel Controls on page 3-128. M. Driver Information Center. See Driver Information Center (DIC) on page 3-57. N. Dual Automatic Climate Controls. See Dual Automatic Climate Control System on page 3-29. O. Center Console Shift Lever (If Equipped). See “Console Shift Lever” under Shifting Into PARK (P) on page 2-36. P. Hazard Warning Flasher Button. See Hazard Warning Flashers on page 3-6. Q. Cupholders. See Cupholder(s) on page 2-55. R. Accessory Power Outlets. See Accessory Power Outlet(s) on page 3-24. S. Rear Window Wiper/Washer. See Rear Window Wiper/Washer on page 3-11. Traction Control System (TCS) Disable Button. See StabiliTrak® System on page 4-6. Tow/Haul Selector Button (If Equipped). See Tow/Haul Mode on page 2-34. Power Liftgate Button (If Equipped). See Power Liftgate on page 2-14. T. Heated Seats Button. See Heated Seats on page 1-5. U. Passenger Air Bag status Indicator. See Passenger Sensing System on page 1-70. V. Glove Box. See Glove Box on page 2-55. 3-5 Hazard Warning Flashers The hazard warning ﬂashers let you warn others. They also let police know you have a problem. The front and rear turn signal lamps will ﬂash on and off. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. The hazard warning ﬂasher button is located in the center of the instrument panel, below the audio system. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. The hazard warning ﬂashers work at all times. However, when they are on, the turn signals will not work. Horn Press near or on the horn symbols on the steering wheel pad to sound the horn. Tilt and Telescopic Steering Wheel A tilt and telescope wheel lets you adjust the steering wheel before you drive. The steering wheel can be raised to the highest level to give your legs more room when you enter and exit the vehicle. The lever that lets you tilt and telescope the steering wheel is located on the left side of the steering column. 3-6 Power Tilt Wheel and Telescopic Steering Column If your vehicle has this feature, the power tilt wheel control is located on the left side of the steering column. To tilt and telescope the steering wheel, pull down the lever. Then move the steering wheel up or down or backward or forward into a comfortable position. Pull the lever up to lock the steering wheel in place. Do not adjust the tilt and telescope lever while driving. To operate the power tilt feature, push the control up and the steering wheel will tilt up. Push the control down and the steering wheel will go down. Push the control forward and the steering wheel moves toward the front of the vehicle. Push the control rearward and the steering wheel moves toward the rear of the vehicle. 3-7 Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: (cid:129) GTurn and Lane Change Signals. See Turn and Lane-Change Signals on page 3-8. (cid:129) 3Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-9. Flash-to-Pass. See Flash-to-Pass on page 3-9. (cid:129) NWindshield Wipers. See Windshield Wipers on page 3-9. (cid:129) LWindshield Washer. See Windshield Washer on page 3-10. For information on the headlamps, see Exterior Lamps on page 3-14. 3-8 Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. To signal a lane change, raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever will return by itself when you release it. If you momentarily press and release the lever, the turn signal will ﬂash three times. If the arrow ﬂashes faster than normal as you signal a turn or a lane change, a signal bulb may be burned out and other drivers will not see your turn signal. (cid:129) If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check for burned-out bulbs and then check the fuse. See Fuses and Circuit Breakers on page 5-100. Turn Signal On Chime If either one of the turn signals are left on and you have drove more than 3/4 mile (1.2 km), a chime will sound. Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever toward the front of the vehicle. This light on the instrument panel cluster comes on if the high beam lamps are turned on while the ignition is on. Flash-to-Pass With the turn signal lever in the low-beam position, pull the lever toward you momentarily to switch to high-beam, to signal that you are going to pass. If the headlamps are on, they will return to low-beam when the lever is released. Windshield Wipers Clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, gently loosen or thaw them. Damaged wiper blades may not clear the windshield well, making it harder to see and drive safely. If the blades do become damaged, install new blades or blade inserts. For more information, see Windshield Wiper Blade Replacement on page 5-47. Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Clear away snow or ice to prevent an overload. Turn the band with the wiper symbol to control the windshield wipers. To change the headlamps from high beam to low beam, pull the turn signal lever toward the rear of the vehicle. 3-9 8(Mist): Turn the band to mist for a single wiping cycle. Hold it there until the wipers start. Then let go. The wipers stop after one wipe. Hold the band on mist longer, for more wipe cycles. 9(Off): To stop the wipers, move the band to off. 6 (Delay): Turn the band to adjust the delay time. The delay between wiping cycles becomes shorter as the band is moved to the top of the lever. This can be very useful in light rain or snow. 1 (Low Speed): Turn the band away from you to the ﬁrst solid band past the delay settings, for steady wiping at low speed. 2 (High Speed): Turn the band further, to the second solid band past the delay settings, for high-speed wiping. Windshield Washer J(Washer Fluid): Press the button located at the end of the turn signal/multifunction lever, to spray washer ﬂuid on the windshield. The wipers clear the windshield and either stop or return to the preset speed. The ignition key must be in ACCESSORY or ON for this to work. See Windshield Washer Fluid on page 5-34 Windshield Washer Fluid. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. WASHER FLUID LOW ADD FLUID is displayed on the Driver Information Center (DIC) when the washer ﬂuid is low. See DIC Warnings and Messages on page 3-66. 3-10 Heated Windshield Washer If your vehicle has the heated windshield washer ﬂuid system it can be used to help clear ice, snow, tree sap, or bugs from the windshield. This feature only works with the front wiper system. The button is located to the left of the steering column below the instrument panel brightness control knob. Push the heated washer ﬂuid button to activate the heated windshield washer ﬂuid system. This activation begins four heated wash/wipe cycles. The ﬁrst heated wash/wipe cycle can take up to 40 seconds to occur, depending on outside temperature. After the ﬁrst wash/wipe cycle, it can take up to 20 seconds for each of the remaining cycles. Press the button again to turn off the heated windshield washer ﬂuid system or it will automatically turn off after four wipe cycles have been completed. When the heated windshield washer ﬂuid system is activated under certain outside temperature conditions, steam might ﬂow out of the washer nozzles for a short period of time before washer ﬂuid is sprayed. This is a normal condition. WASHER FLUID LOW ADD FLUID is displayed on the DIC when the washer ﬂuid is low. See DIC Warnings and Messages on page 3-66. Rear Window Wiper/Washer The rear wiper and rear wash button is located on the instrument panel below the climate control system. Z (Rear Wiper): Press this symbol to turn the rear wiper on and off. The wiper speed cannot be changed. Y (Wash): Press this symbol to spray washer ﬂuid on the rear window. The window wiper will also come on. Release the button when enough ﬂuid has been sprayed on the window. The rear wiper will run a few more cycles after it is released. If the rear wiper function was already on, prior to pressing the wash button, it will stay on until the wiper button is pressed again. The rear window washer uses the same ﬂuid that is in the windshield washer reservoir. See Windshield Washer Fluid on page 5-34. 3-11 Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When you apply your brakes, cruise control is turned off. {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. 3-12 The cruise control buttons are located on left side of the steering wheel. T (On/Off): Press this button to turn cruise control on and off. The indicator comes on when cruise control is on. + RES (Resume/Accelerate): Press this button to make the vehicle accelerate or resume to a previously set speed. SET–: Press this button to set the speed or make the vehicle decelerate. [ (Cancel): Press this button to cancel cruise control. Setting Cruise Control Cruise control will not work if your parking brake is set, or if the master cylinder brake ﬂuid level is low. The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed. {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Press the cruise control on/off button. 2. Get up to the speed desired. 3. Press and release the SET– button located on the steering wheel. 4. Take your foot off the accelerator. Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This shuts off the cruise control. But you do not need to reset it. Once you are driving about 25 mph (40 km/h) or more, press the +RES button on your steering wheel. The vehicle will go back to the previously chosen speed and stay there. Increasing Speed While Using Cruise Control To increase the cruise speed while using cruise control: (cid:129) Press and hold the +RES button on the steering wheel until you reach the desired speed, then release it. To increase vehicle speed in small increments, press the +RES button. Reducing Speed While Using Cruise Control To reduce your speed while using cruise control: (cid:129) Press and hold the SET– button on the steering wheel until you reach the lower speed desired, then release it. To slow down in very small amounts, press the SET– button on the steering wheel brieﬂy. Each time this is done, the vehicle will go about 1 mph (1.6 km/h) slower. 3-13 (cid:129) (cid:129) Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase vehicle speed. When you take your foot off the pedal, your vehicle will slow down to the previously set cruise speed. Using Cruise Control on Hills How well your cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle speed down. Of course, applying the brake turns off the cruise control. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control There are three ways to end cruise control: (cid:129) Step lightly on the brake pedal. (cid:129) Press the [ (cancel) button on the steering wheel. (cid:129) Press the T(on/off) button on the steering wheel. Erasing Speed Memory The cruise control set speed memory is erased by turning off the cruise control or the ignition. 3-14 Exterior Lamps The exterior lamps control is located on the instrument panel to the left of the steering wheel. It controls the following systems: (cid:129) Headlamps Taillamps (cid:129) Parking Lamps License Plate Lamps Instrument Panel Lights Fog Lamps The exterior lamps control has four positions: 9(Off): Brieﬂy turn the control to this position to turn off the automatic light control. Brieﬂy turn to this position again to turn automatic light control on again. (cid:129) (cid:129) (cid:129) (cid:129) AUTO (Automatic): Turn the control to this position to automatically turn on the headlamps at normal brightness, together with the following: (cid:129) Parking Lamps Taillamps License Plate Lamps Instrument Panel Lights ;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: Taillamps License Plate Lamps Instrument Panel Lights 2(Headlamps): Turn the control to this position to turn on the headlamps together with the following lamps listed below. A warning chime will sound if you open the driver’s door when the ignition switch is off and the headlamps are on. (cid:129) Parking Lamps Taillamps License Plate Lamps Instrument Panel Lights -(Fog Lamps): Push the fog lamps control in to turn on the fog lamps. See Fog Lamps on page 3-16. Delayed Headlamps The delayed headlamps feature provides a period of exterior lighting as you leave the area around your vehicle. The feature is activated when the headlamps are on due to the automatic headlamps control feature described previously in this section, and when the ignition is turned off. Your headlamps will then remain on until the exterior lamps control is moved to the parking lamps position or until the pre-selected delayed headlamp lighting period has ended. If you turn off the ignition with the headlamps switch in the parking lamps or headlamps position, the delayed headlamps cycle will not occur. To disable the delayed headlamps feature or change the time of delay, see DIC Vehicle Customization (With DIC Buttons) on page 3-75. 3-15 (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) Daytime Running Lamps (DRL)/ Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. A light sensor on top of the instrument panel makes the DRL work, so be sure it is not covered. The DRL system’s automatic headlamp control will make the low-beam headlamps come on at a reduced brightness when the following conditions are met: The ignition is in the ON/RUN position. The exterior lamps control is in AUTO. The engine is running. When the DRL are on, only the low-beam headlamps, at a reduced level of brightness, will be on. The headlamps, taillamps, sidemarker, and other lamps will not be on. The instrument panel and cluster will also not be lit. When it is dark enough outside, the low-beam headlamps will turn off and the headlamps and parking lamps will turn on. The other lamps that come on with the headlamps will also come on. 3-16 When it is bright enough outside, the headlamps will go off and the DRL will come on. As with any vehicle, you should turn on the regular headlamp system when it is needed. Fog Lamps Use the fog lamps for better vision in foggy or misty conditions. -(Fog Lamps): The fog lamps button is located on the exterior lamps control. The exterior lamps control is located on the instrument panel to the left of the steering column. The ignition must be on for the fog lamps to work. Press the exterior lamps button to turn the fog lamps on or off. A light will come on in the instrument panel cluster when the fog lamps are in use. When the headlamps are changed to high-beam, the fog lamps will turn off. The fog lamps come back on again when the high-beam headlamps are turned off. Some localities have laws that require the headlamps to be on along with the fog lamps. (cid:129) (cid:129) (cid:129) Instrument Panel Brightness D (Instrument Panel Brightness): The knob with this symbol on it is located next to the exterior lamps control. Push the knob in all the way until it extends out and then turn the knob clockwise to brighten or counterclockwise to dim the lights. Push the knob back in when ﬁnished. Courtesy Lamps When a door is opened, the courtesy lamps automatically come on. They make it easy for you to enter and leave your vehicle. You can also manually turn these lamps on by fully turning the instrument panel brightness control clockwise. The reading lamps, located on the headliner above the rearview mirror, can be turned on or off independent of the automatic courtesy lamps, when the doors are closed. Dome Lamps The dome lamps automatically come on when a door is opened, unless the dome lamp override button is pressed in. The lamps can also be turned on and off by turning the instrument panel brightness control clockwise to the farthest position. Dome Lamp Override The dome lamp override button is located next to the exterior lamps control. The dome lamp override is used to set the dome lamps to remain off or come on automatically when a door is opened. E (Dome Lamp Override): Press the button in and the dome lamps remain off when a door is opened. Press the button again to return it to the extended position so that the dome lamps come on when a door is opened. Entry Lighting Your vehicle may have courtesy lamps that will come on and stay on for a set time whenever the unlock symbol is pressed on the Remote Keyless Entry (RKE) Transmitter, if the vehicle has one. If a door is opened, the lamps stay on while it is open and then turn off automatically about 25 seconds after the door is closed. If the unlock symbol is pressed and you do not open a door, the lamps turn off after about 20 seconds. 3-17 Entry lighting includes a feature called theater dimming. With theater dimming, the lamps do not turn off at the end of the delay time. Instead, they slowly dim after the delay time until they go out. The delay time is canceled if you turn the ignition key to ON/RUN or press the power door lock switch. The lamps will dim right away. When the ignition is on, illuminated entry is inactive, which means the courtesy lamps will not come on unless a door is opened. Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after all the doors have been closed, the delayed entry lighting feature will continue to work until one of the following occurs: The ignition is in ON/RUN. The doors are locked. (cid:129) An illumination period of 25 seconds has elapsed. If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open. 3-18 Delayed Exit Lighting This feature illuminates the interior for a period of time after the key is removed from the ignition. The ignition must be off for delayed exit lighting to work. When the key is removed, interior illumination will activate and remain on until one of the following occurs: The ignition is in ON/RUN. The power door locks are activated. (cid:129) An illumination period of 20 seconds has elapsed. If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open. Parade Dimming The instrument panel has an added feature called parade mode. It automatically prohibits the dimming of the instrument panel displays during the daylight while the headlamps are on so that you will still be able to see the displays. (cid:129) (cid:129) (cid:129) (cid:129) Reading Lamps The vehicle has reading lamps that also act as the dome lamp. Press the button to turn them on and off. Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as Battery Saver Active or Service Battery Charging System. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. See DIC Warnings and Messages on page 3-66. 3-19 Battery Run-Down Protection This vehicle has a feature to help prevent the battery from being drained, if the interior courtesy lamps, reading/map lamps, visor vanity lamps or trunk lamp are accidentally left on. If any of these lamps are left on, they will automatically turn off after 10 minutes, if the ignition is off. The lamps will not come back on again until one of the following occurs: The ignition is turned on. The exterior lamps control is turned off, then on again. The headlamps will timeout after 10 minutes, if they are manually turned on before the ignition is off. Head-Up Display (HUD) {CAUTION: If the HUD image is too bright or too high in your ﬁeld of view, it may take you more time to see things you need to see when it is dark outside. Be sure to keep the HUD image dim and placed low in your ﬁeld of view. If the vehicle has the Head-Up Display (HUD), some information concerning the operation of the vehicle is projected onto the windshield. This includes the speedometer reading, RPM reading, transmission position, outside air temperature, the tap shift gear, and a brief display of the current radio station, including XM information or CD track. It will also display turn-by-turn navigation information if the vehicle has a navigation radio. The images are projected by the HUD lens located on the driver’s side of the instrument panel. The tap shift gear will also appear on the HUD if the vehicle has tap shift and it is active. 3-20 (cid:129) (cid:129) The HUD information can be displayed in one of three languages, English, French, or Spanish. The speedometer reading and other numerical values can be displayed in either English or metric units. The language selection and the units of measurement are changed through the trip computer in the Driver Information Center (DIC). See DIC Vehicle Customization (With DIC Buttons) on page 3-75. The HUD information appears as an image focused out toward the front of the vehicle. When the ignition key is turned to RUN, the HUD will display an introductory message for a short time, until the HUD is ready. The following indicator lights come on the instrument panel when activated and will also appear on the HUD: Turn Signal Indicators (cid:129) High-Beam Indicator Symbol The HUD will temporarily display CHECK GAGES and ICE POSSIBLE when there are messages on the DIC trip computer. The HUD will also display the following messages on vehicles with these systems, when they are active: TRACTION CONTROL ACTIVE (cid:129) STABILITRAK ACTIVE If you try to use the HUD image as a parking Notice: aid, you may misjudge the distance and damage your vehicle. Do not use the HUD image as a parking aid. When the HUD is on, the speedometer reading will continually be displayed. The current radio station or CD track number will display for a short period of time after the radio or CD track status changes. This will happen whenever radio information is changed. The speedometer size will be reduced when radio, CD information, warnings, or turn-by-turn navigation information are displayed on the HUD. 3-21 (cid:129) (cid:129) The HUD control is located to the right of the steering wheel. w (Up): x(Down): Press the up or down arrows to center the HUD image in your view. The HUD image can only be adjusted up and down, not side to side. ? (Page): Press this button to select the display formats. Release the page button when the format number with the desired display is shown on the HUD. The three formats are as follows: To adjust the HUD image so that items are properly displayed, do the following: 1. Adjust the driver’s seat to a comfortable position. 2. Start the engine. 3. Adjust the HUD controls. Use the following settings to adjust the HUD. 9(Off): To turn HUD off, rotate the dimming knob fully counterclockwise until the HUD display turns off. Brightness: Turn the knob on the HUD control clockwise to brighten the display and counterclockwise to dim it. 3-22 Format One: This display gives the speedometer reading (in English or metric units), turn signal indication, high beam indication, transmission positions, and the outside air temperature. Format Two: This display includes the information in Format One without the transmission information and the outside air temperature. Format Three: This display includes all the information in Format One along with a circular tachometer, but without outside air temperature. All formats will show the turn-by-turn navigation information and provide details about the next driving maneuver to be made. When you near your destination, the HUD will display a distance bar that will ﬁll in the closer you get to your destination. All navigation information is provided to the HUD by the navigation radio, if the vehicle has one. The HUD image displayed on the windshield will automatically dim and brighten to compensate for outside lighting. The HUD image can temporarily light up depending on the angle and position of the sunlight on the HUD display. This is normal and will change when the angle of the sunlight on the HUD display changes. Polarized sunglasses could make the HUD image harder to see. Care of the HUD Clean the inside of the windshield as needed to remove any dirt or ﬁlm that could reduce the sharpness or clarity of the HUD image. To clean the HUD lens, use a soft, clean cloth that has household glass cleaner sprayed on it. Wipe the HUD lens gently, then dry it. Do not spray cleaner directly on the lens because the cleaner could leak into the unit. 3-23 If You Cannot See the HUD Image When the Ignition Is On Is anything covering the HUD lens? Is the HUD dimmer setting bright enough? Is the HUD image adjusted to the proper height? (cid:129) Are you wearing polarized sunglasses? (cid:129) Still no HUD image? Check the fuse in the instrument panel fuse block. See Instrument Panel Fuse Block on page 5-100. If the HUD Image Is Not Clear Is the HUD image too bright? (cid:129) Are the windshield and HUD lens clean? If the HUD image is not correct, contact your dealer/retailer. Keep in mind that the windshield is part of the HUD system. Accessory Power Outlet(s) The accessory power outlets can be used to connect electrical equipment such as a cellular phone or CB radio. Your vehicle may have four accessory power outlets. They are located on the instrument panel below the climate controls, inside the front center console storage bin, at the rear of the center console, and in the rear cargo area. To use the outlets, remove the cover. When not in use, always cover the outlet with the protective cap. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating of 20 amperes. 3-24 (cid:129) (cid:129) (cid:129) (cid:129) Power Outlet 115 Volt Alternating Current Your vehicle may have a power outlet that can be used to plug in electrical equipment that uses a maximum limit of 150 watts. The power outlet is located on the rear of the center console. Certain electrical accessories may not be compatible with the accessory power outlets and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer/retailer for additional information on the accessory power outlet. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment. When adding electrical equipment, be sure to follow the installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. An indicator light on the outlet turns on to show it is in use. The light comes on when the ignition is in ON/RUN and equipment requiring less than 150 watts is plugged into the outlet, and no system fault is detected. 3-25 The indicator light does not come on when the ignition is in LOCK/OFF or if no equipment is plugged into the outlet. If you try to connect equipment using more than 150 watts or a system fault is detected, a protection circuit shuts off the power supply and the indicator light turns off. To reset the circuit, unplug the item and plug it back in or turn the Remote Accessory Power (RAP) off and then back on. See Retained Accessory Power (RAP) on page 2-27. The power restarts when equipment using 150 watts or less is plugged into the outlet and a system fault is not detected. The power outlet is not designed for the following electrical equipment and may not work properly if these items are plugged into the power outlet: (cid:129) Equipment with high initial peak wattage such as: compressor-driven refrigerators and electric power tools. (cid:129) Other equipment requiring an extremely stable power supply such as: microcomputer-controlled electric blankets, touch sensor lamps, etc. See High Voltage Devices and Wiring on page 5-99. 3-26 Climate Controls Climate Control System With this system you can control the heating, cooling, defrost, defog, and ventilation of the vehicle. Manual Operation 9(Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob all the way counterclockwise to turn the front system off. Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the temperature of the air ﬂowing from the system. Airﬂow Mode Control: Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of the vehicle. To change the current mode, select one of the following: H (Vent): This mode directs air to the instrument panel outlets. ) (Bi-Level): This mode directs about half of the air to the instrument panel outlets and half to the ﬂoor outlets. A little air is directed towards the windshield and side window outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. 6 (Floor): This mode directs most of the air to the ﬂoor outlets, with some of the air directed to the windshield, side window outlets, and second row ﬂoor outlets. In this mode, the system automatically selects outside air. Recirculation cannot be selected when in Floor Mode. The right knob can also be used to select defog or defrost mode. For more information, see “Defogging and Defrosting” later in this section. By positioning the right knob between two modes, a combination of those two modes is selected. @ (Recirculation): Press this button to turn the recirculation mode on or off. The indicator light on the button turns on when this mode is selected. This mode keeps outside air from entering the vehicle. It can be used to reduce the outside air and odors entering the vehicle. Recirculation may also help cool the air inside the vehicle more quickly once the temperature inside the vehicle is less than the outside temperature. The recirculation mode can be turned off in vent and bi-level modes by pressing the button again. Recirculation mode automatically turns off when the engine is turned off and must be re-selected when the engine is turned on again. The recirculation mode cannot be used with ﬂoor, defrost, or defogging modes. If you try to select recirculation in one of those modes, the indicator ﬂashes three times and turns off. The air conditioning compressor also comes on when this mode is activated unless the outside air temperature is less than 40°F (4°C). While in recirculation mode the windows may fog when the weather is cold and damp. To clear the fog, select either the defog or defrost mode and increase the fan speed. #(Air Conditioning): Press this button on the left knob to turn the air conditioning system on or off. When A/C is pressed, an indicator light comes on to show that the air conditioning has been activated. The air conditioning compressor does not operate when outside temperatures fall below 40°F (4°C). The indicator light ﬂashes three times and turns off when outside conditions affect air conditioning operation. This is normal. 3-27 For quicker cool down on hot days, do the following: 1. Open the windows to let hot air escape. 2. Select the vent mode. 3. Select the air conditioner. 4. Select the coolest temperature. 5. Select the highest fan speed. 6. Close the windows after the hot air has escaped. 7. Once the vehicle’s interior temperature is below the outside temperature, select recirculation mode for better cooling. This helps to reduce the time it takes for the vehicle to cool down. It also helps the system to operate more efficiently. Using recirculation for long periods of time may cause the air inside of the vehicle to become too dry. To prevent this from happening, after the inside of the vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air, so you might notice a small amount of water dripping underneath the front center and right rear of the vehicle while idling or after turning off the engine. This is normal. Defogging and Defrosting Fog on the inside of the windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from the windshield. Turn the right knob clockwise to select the defog or defrost mode. -(Defog): The defog mode is used to clear the windows of fog or moisture and warm the passengers. This mode directs air to the windshield, ﬂoor outlets, and side window vents. When you select this mode, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is less than 40°F (4°C). The recirculation mode cannot be selected while in the defog mode. Do not drive the vehicle until all the windows are clear. 0(Defrost): The defrost mode is used to remove fog or frost from the windshield more quickly. This mode directs most of the air to the windshield and side window vents and some to the ﬂoor vents. In this mode, the system will automatically force outside air into your vehicle. The recirculation mode cannot be selected while in the defrost mode. The air conditioning compressor will run automatically in this setting, unless the outside temperature is less than 40°F (4°C). Do not drive the vehicle until all the windows are clear. 3-28 AUX (Auxiliary): Press this button to turn the rear heating and air conditioning on. See Rear Air Conditioning and Heating System on page 3-36 or Rear Air Conditioning and Heating System and Electronic Climate Controls on page 3-38. Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. <(Rear Window Defogger): Press this button on the right knob to turn the rear window defogger on or off. The rear window defogger stays on about 10 minutes after the button is pressed, before turning off. The defogger can also be turned off by pressing the button again or by turning off the engine. Do not drive the vehicle until all the windows are clear. If your vehicle has heated outside rearview mirrors, the mirrors heat to help clear fog or frost from the surface of the mirror when the rear window defog button is pressed. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid. Dual Automatic Climate Control System The heating, cooling, and ventilation in your vehicle can be controlled with this system. Your vehicle also has a ﬂow-through ventilation system described later in this section. Different temperature settings can be selected for the driver and all passengers. Display Function Each time the temperature, mode, or fan control buttons are pressed the display shows that function along with the inside temperature setting. The display automatically reverts back to the outside temperature display after a short delay. 3-29 Driver’s Side Temperature Control The driver side temperature buttons are used to adjust the temperature of the air coming through the system on the driver side. The temperature can be adjusted even if the system is turned off. This is possible since outside air will always ﬂow through the system as the vehicle is moving forward unless it is set to recirculation mode. See “Recirculation” later in this section. Press the + or − buttons to increase or decrease the temperature. The driver side temperature display will show the temperature setting decreasing or increasing. Passenger’s Side Temperature Control The passenger’s temperature buttons can be used to change the temperature of the air coming through the system on the passenger side of the vehicle. The temperature can be adjusted even if the system is turned off. This is possible since outside air will always ﬂow through the system as the vehicle is moving forward unless it is set to recirculation mode. See “Recirculation” later in this section. Press the + or − buttons to increase or decrease the temperature. The passenger side display will show the temperature setting decreasing or increasing. The passenger’s temperature setting can be set to match the driver’s temperature setting by pressing the PASS button and turning off the PASS indicator. 3-30 When the passenger’s temperature setting is set different than the driver’s setting, the indicator on the PASS button comes on and both the driver side and passenger side temperature displays are shown. Automatic Operation AUTO (Automatic): When automatic operation is active the system controls the inside temperature, the air delivery, and the fan speed. Use the steps below to place the entire system in automatic mode: 1. Press the AUTO button. When AUTO is selected, the display shows the current temperature(s) selected and AUTO is on the display. The current delivery mode and fan speed also display for approximately 5 seconds. When AUTO is selected, the air conditioning operation and air inlet are automatically controlled. The air conditioning compressor runs when the outside temperature is over about 40°F (4°C). The air inlet is normally set to outside air. If it is hot outside, the air inlet can automatically switch to recirculate inside air to help quickly cool down your vehicle. The light comes on the recirculation button while in recirculation. 2. Set the driver’s and passenger’s temperature. To ﬁnd your comfort setting, start with a 73°F (22°C) temperature setting and allow about 20 minutes for the system to regulate. Use the driver’s or passenger’s temperature buttons to adjust the temperature setting as necessary. If you choose the temperature setting of 60°F (15°C), the system remains at the maximum cooling setting. If you choose the temperature setting of 90°F (32°C), the system remains at the maximum heat setting. Choosing either maximum setting will not cause the vehicle to heat or cool any faster. Do not cover the solar sensor located on the top of the instrument panel near the windshield. This sensor regulates air temperature based on sun load and also turns on your vehicle’s headlamps. For more information on the solar sensor, see “Sensors” later in this section. To avoid blowing cold air in cold weather, the system delays turning on the fan until warm air is available. The length of delay depends on the engine coolant temperature. Press the fan switch to override this delay and change the fan to a selected speed. O(On/Off): Press this button to turn off the climate control system. Outside air still enters the vehicle, and is directed to the ﬂoor. This direction can be changed by pressing the mode button. Recirculation can only be selected in vent or bi-level mode. The temperature can also be adjusted using either temperature button. If you adjust the air delivery mode or temperature settings with the system off, the display comes on brieﬂy to show the settings and then turns off. Press the on/off button or the up down arrows on the fan switch, the defrost button, AUTO button, or the air conditioning button to turn the system on when it is off. Manual Operation The air delivery mode or fan speed can be manually adjusted. DC (Fan): The buttons with the fan symbols let you manually adjust the fan speed. Press the up arrow to increase fan speed and the down arrow to decrease fan speed. Pressing a fan button while the system is off will turn the system on. Pressing a fan button while in automatic control places the fan under manual control. The fan setting remains displayed, the word AUTO is no longer displayed, and the AUTO button indicator light turns off. The air delivery mode remains in automatic control. yN z(Mode): Press the mode up and down buttons to manually change the direction of the airﬂow in the vehicle. Repeatedly press the button until the desired mode appears on the display. Pressing a mode button while the system is off will change air delivery mode without turning the system on. Pressing one of these buttons while in automatic control to place the mode under manual control. 3-31 The air delivery mode setting remains displayed, the word AUTO is no longer displayed, and the AUTO button indicator light turns off. H (Vent): This setting delivers air to the instrument panel outlets. ) (Bi-Level): This mode directs air to the instrument panel outlets and to the ﬂoor outlets. A little air is directed towards the windshield and side window outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. 6 (Floor): This mode directs most of the air to the ﬂoor outlets, with some of the air directed to the windshield, side window outlets, and second row ﬂoor outlets. In this mode, the system automatically selects outside air. Recirculation cannot be selected in ﬂoor mode. - (Defog): See “Defogging and Defrosting” later in this section. @ (Recirculation): Press this button to turn the recirculation mode on. When the button is pressed, an indicator light comes on. This mode keeps outside air from entering the vehicle. It can be used to reduce outside air and prevent odors from entering your vehicle. Recirculation also helps to quickly cool the warmer air inside your vehicle. The recirculation mode cannot be used with ﬂoor, defrost, or defogging modes. If you try to select recirculation in one of those modes, the indicator ﬂashes three times and turns off. The air conditioning compressor also comes on when this mode is activated. While in recirculation mode the windows may fog when the weather is cold and damp. To clear the fog, select either the defog or defrost mode and increase the fan speed. Press the button again to turn off the recirculation mode. It automatically turns off when the engine is turned off and must be re-selected when the engine is turned on again. 3-32 Air Conditioning #(Air Conditioning): Press this button to turn the air conditioning (A/C) compressor on and off. When air conditioning is selected, an indicator light comes on to show that the air conditioning has been activated. The air conditioning compressor does not work when outside temperatures fall below 40°F (4°C). Pressing this button when the outside temperature is too cool makes the air conditioning indicator ﬂash three times and turn off to let you know the air conditioning mode is not available. If the air conditioning is on and the outside temperature drops below a temperature which is too cool for air conditioning to be effective, the air conditioning light turns off to show that the air conditioning mode has been canceled. On hot days, open the windows long enough to let hot inside air escape. This helps to reduce the time it takes for the vehicle to cool down. It also helps the system to operate more efficiently. The air conditioning system removes moisture from the air, so a small amount of water may drip underneath your vehicle while idling or after turning off the engine. This is normal. Sensors The solar sensor, located in the defrost grille in the middle of the instrument panel, monitors the solar radiation. Do not cover the solar sensor or the system will not work properly. 3-33 The climate control system uses the information from these sensors to maintain your comfort setting by adjusting the outlet temperature, fan speed, and the air delivery mode. The system may also supply cooler air to the side of the vehicle facing the sun. The recirculation mode will also be used as needed to maintain cool outlet temperatures. Defogging and Defrosting Fog on the inside of the windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield. Use the mode up and down arrows to select the defog mode. Use the defrost button to select the defrost mode. - (Defog): The defog mode is used to clear the windows of fog or moisture and warm the passengers. This mode directs air to the windshield, ﬂoor outlets, and side window vents. When this mode is selected, the system turns off recirculation and runs the air conditioning compressor unless the outside temperature is close to freezing. The recirculation mode cannot be selected while in the defog mode. Do not drive the vehicle until all the windows are clear. The interior temperature sensor located on the instrument panel to the right of the steering column, measures the temperature of the air inside the vehicle. There is also an exterior temperature sensor located behind the front grille. This sensor reads the outside air temperature and helps maintain the temperature inside the vehicle. Any cover on the front of the vehicle could cause a false reading in the displayed temperature. 3-34 To clear fog from the rear seat side windows, select the bi-level mode on the rear climate control system and direct the headliner outlets toward the side windows. 0 (Defrost): Press this button to remove fog or frost from the windshield more quickly. This mode directs most of the air to the windshield and side window vents and some to the ﬂoor vents. In this mode, the system automatically forces outside air into the vehicle. The recirculation mode cannot be selected while in the defrost mode. The air conditioning compressor runs automatically in this setting, unless the outside temperature is close to freezing. Do not drive the vehicle until all the windows are clear. While in defrost mode, if the PASS button is pressed, the PASS button indicator will ﬂash three times to let you know that the passenger climate control system cannot be activated. If the passenger temperature buttons are adjusted while in defrost mode, the driver temperature indicator will change. The passenger temperature will not be displayed. AUX (Auxiliary): Press this button to turn the rear heating and air conditioning on. See Rear Air Conditioning and Heating System on page 3-36 or Rear Air Conditioning and Heating System and Electronic Climate Controls on page 3-38. Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. < (Rear Window Defogger): Press this button to turn the rear window defogger on or off. The rear window defogger stays on for about 10 minutes after the button is pressed, before turning off. The defogger can also be turned off by pressing the button again or by turning off the engine. Do not drive the vehicle until all the windows are clear. If your vehicle has heated outside rearview mirrors, the mirrors will heat to help clear fog or frost from the surface of the mirror when the rear window defog button is pressed. Notice: Do not use a razor blade or sharp object to clear the inside rear window. Do not adhere anything to the defogger grid lines in the rear glass. These actions may damage the rear defogger. Repairs would not be covered by your warranty. 3-35 Outlet Adjustment Use the slider switch in the center of the outlet, to change the direction of the air ﬂow. Use the thumbwheel near the outlet to control the amount of air ﬂow or to shut off the airﬂow completely. Keep all outlets open whenever possible for best system performance. Operation Tips (cid:129) Clear away any ice, snow, or leaves from the air inlets at the base of the windshield that can block the ﬂow of air into the vehicle. (cid:129) Use of non-GM approved hood deﬂectors can adversely affect the performance of the system. (cid:129) Keep the path under all seats clear of objects to help circulate the air inside the vehicle more effectively. If fogging reoccurs while in vent or bi-level modes with mild temperature throughout the vehicle, turn on the air conditioner to reduce windshield fogging. Rear Air Conditioning and Heating System If your vehicle has this system, the rear controls are three knobs located on the rear of the center console. The system can be controlled from the front controls as well as the rear controls. To turn the system on, press the AUX button on the front climate control system, an indicator will be lit. Pressing the AUX button the ﬁrst time will turn the rear system on in a mimic mode. In this mode, the airﬂow in the rear will be approximately the same direction, temperature, and fan speed as the front. Pressing the AUX button again will turn the rear system and the indicator off. If the rear controls are adjusted, the system turns on in a rear independent mode. Airﬂow in the rear will then be directed according to the settings of the rear controls. The rear system can be turned off by pressing the AUX button on the front climate control system and the indicator will turn off. The system can be turned back on, by adjusting any of the rear air conditioning control knobs. 3-36 (cid:129) Fan Knob Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob all the way counterclockwise to turn the rear system off. Temperature Knob The middle knob on the control panel lets you select the temperature of the air ﬂowing into the passenger area. Turn the knob clockwise or counterclockwise for warmer or cooler air. Mode Knob The right knob on the control panel lets you choose the direction of the air ﬂow. H(Vent): This setting directs the air through the headliner outlets. )(Bi-Level): This setting directs the air through the rear ﬂoor outlets under the third row seat, as well as the headliner outlets. The ﬂow can be divided between headliner and ﬂoor outlets depending upon where the knob is placed between the settings. 6(Floor): This setting directs the air through the ﬂoor outlets. The rear system ﬂoor outlets are located under the third row seats. 3-37 Rear Air Conditioning and Heating System and Electronic Climate Controls If your vehicle has this rear climate control system there are rear seat audio controls located in the center console. The rear system can be controlled through the AUX button on the front climate control panel. Press the AUX button to turn the rear climate control system on or off. An indicator light in the AUX button comes on when the rear climate control system is on. The direction, temperature, and speed of the airﬂow for the rear of the vehicle will be the same as those set for the front of the vehicle. Use the controls located in the rear of the front console, to independently control the air ﬂow for the rear of the vehicle separately from that of the front of the vehicle. To turn the system on, press any of the rear air conditioning control buttons, except the C button. To turn the system off, press and hold the C button. 3-38 Rear Climate Control with Rear Seat Audio Controls Manual Operation DC (Fan): The fan buttons on the rear seat audio control panel let you manually adjust the fan speed. Press D to increase airﬂow and C to decrease airﬂow. +/− (Increase/Decrease Temperature): These buttons select the temperature of the air ﬂowing into the rear passenger area. Press the + button for warmer air and press the − button for cooler air. The temperature settings will display in 0-12 increments, going from the coolest (0) to the warmest (12) setting. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As the details show on the next few pages, some warning lights come on brieﬂy when you start the engine just to let you know they are working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there is a problem with your vehicle. When one of the warning lights comes on and stays on as you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly and even dangerous. So get to know your vehicle’s warning lights and gages. They can be a big help. N (Mode): Press the mode button to manually change the direction of the airﬂow in the vehicle. Repeatedly press the button until the desired mode appears on the display. Multiple presses cycles through the delivery selections. H (Vent): This mode directs air through the headliner outlets. ) (Bi-Level): This mode directs air through the ﬂoor outlets as well as the headliner outlets. The rear system ﬂoor outlets are located under the third row seats. 6 (Floor): This mode directs air through the ﬂoor outlets. The rear system ﬂoor outlets are located under the third row seats. Warning Lights, Gages, and Indicators This section describes the warning lights and gages on your vehicle. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gages could also save you or others from injury. 3-39 Instrument Panel Cluster The instrument cluster is designed to let you know at a glance how the vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically. United States version shown, Canada similar 3-40 Speedometer and Odometer The speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far your vehicle has been driven, in either miles or kilometers. Your vehicle has a tamper-resistant odometer. If your vehicle needs a new odometer installed, the new one will be set to the mileage total of the old odometer. If this is not possible, it will be set at zero and a label must be put on the driver’s door to show the old mileage reading when the new odometer was installed. If the mileage is unknown, the label should then indicate “previous mileage unknown”. Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. The safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. This chime and light is repeated if the driver remains unbuckled and the vehicle is in motion. If the driver’s belt is already buckled, neither the chime nor the light will come on. 3-41 Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 1-70 for more information. The passenger safety belt light, located on the instrument panel, will come on and stay on for several seconds and then ﬂash for several more. This chime and light are repeated if the passenger remains unbuckled and the vehicle is in motion. If the passenger’s safety belt is buckled, neither the chime nor the light will come on. Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-61. This light will come on when you start your vehicle, and it will ﬂash for a few seconds. The light should go out and the system is ready. If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. 3-42 {CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. The airbag readiness light should ﬂash for a few seconds when you start the engine. If the light does not come on then, have it ﬁxed immediately. If there is a problem with the airbag system, an airbag Driver Information Center (DIC) message may also come on. See DIC Warnings and Messages on page 3-66 for more information. Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your instrument panel has a passenger airbag status indicator. United States Canada When you start the vehicle, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. If you use remote start to start your vehicle from a distance, if equipped, you may not see the system check. 3-43 Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal and seat-mounted side impact airbags. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag and seat-mounted side impact airbag are enabled (may inﬂate). {CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag and seat-mounted side impact airbag (if equipped). A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Do not use a rear-facing child restraint in the right front passenger’s seat if the airbag is turned on. 3-44 {CAUTION: Even though the passenger sensing system is designed to turn off the right front passenger’s frontal airbag and seat-mounted side impact airbag (if equipped) if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be secured in a rear seat, even if the airbag is or airbags are off. If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal airbag and seat-mounted side impact airbag. See Passenger Sensing System on page 1-70 for more on this, including important safety information. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. {CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the airbag(s). See Airbag Readiness Light on page 3-42 for more on this, including important safety information. Charging System Light This light will come on brieﬂy when you turn on the ignition, but the engine is not running, as a check to show you it is working. It should go out once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the charging system. A charging system Driver Information Center (DIC) message may also appear. See DIC Warnings and Messages on page 3-66 for more information. This light could indicate that you have problems with a generator drive belt, or another electrical problem. Have it checked right away. If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and air conditioner. 3-45 Voltmeter Gage When the engine is not running, but the ignition is turned on, this gage shows the battery’s state of charge in DC volts. When the engine is running, this gage shows the condition of the charging system. The vehicle’s charging system regulates voltage based on the state of charge of the battery. The voltmeter may ﬂuctuate. This is normal. Readings between the low and high warning zones indicate the normal operating range. Readings in the low warning zone may occur when a large number of electrical accessories are operating in the vehicle and the engine is left idling for an extended period. If there is a problem with the battery charging system, a SERVICE BATTERY CHARGING SYSTEM message will appear in the Driver Information Center (DIC) and/or the charging system light will come on. See DIC Warnings and Messages on page 3-66 and Charging System Light on page 3-45 for more information. However, readings in either warning zone may indicate a possible problem in the electrical system. Have the vehicle serviced as soon as possible. 3-46 Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem. Have your brake system inspected right away. When the ignition is on, the brake system warning light will also come on when you set your parking brake. The light will stay on if your parking brake does not release fully. If it stays on after your parking brake is fully released, it means you have a brake problem. If the light comes on while you are driving, pull off the road and stop carefully. Make sure the parking brake

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2008 GMC Acadia Owners Manual