2005 Ford FIVE Hundred Owners Manual

SET

51

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).

OFF

ON

CNCL

RSM

SET

SET

• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the SET - control until you get to the desired speed, then release the control. You can also use the SET - control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1
mph (1.6 km/h). • Depress the brake pedal or press CNCL (Cancel) until the desired vehicle speed is reached, press the SET + control.

OFF

ON

CNCL

RSM

SET

SET

OFF

ON

CNCL

RSM

SET

SET

52

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or press CNCL (Cancel). This will not erase your vehicle’s previously set speed.

• Press the speed control OFF

control.

Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

STEERING WHEEL CONTROLS (IF EQUIPPED)

Radio control features • Press MEDIA to select AM, FM1,

FM2, or CD (if equipped).

In Radio mode: • Press SEEK to access the

next/previous strong station.

In CD mode: • Press SEEK to listen to the next

track on the disc.

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

OFF

ON

CNCL

RSM

SET

SET

VOL

SEEK

MEDIA

MUTE

VOL

SEEK

MEDIA

MUTE

53

Driver Controls

In any mode: • Press VOL up or down to adjust • Press MUTE to mute the volume.

the volume.

MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up to ventilate the vehicle. To open the moon roof: The moon roof is equipped with an automatic, one-touch, express opening and closing feature. To stop motion at any time during the one-touch operation, press the control a second time. To open the moon roof, press and release the rear portion of the control. To close the moon roof: To close, press and release the front portion of the control. To vent: To tilt the moon roof into the vent position (when the glass panel is closed), press and hold the middle portion of the control. To close the moon roof from the vent position, press and hold the front portion of the control until the glass panel stops moving. The moon roof has a sliding shade that can be opened or closed when the glass panel is shut. To close the shade, pull it toward the front of the vehicle

Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.

When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the

proximity of the moon roof opening.

54

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.

When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of

the way to prevent potential harm or damage.

Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.

Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the ACC position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal.

55

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat Step 1
to program additional hand-held transmitters to the remaining two HomeLink威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink威. 2. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your visor) while keeping the indicator light in view. 3. Simultaneously press and hold both the HomeLink威 and hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator and Canadian Programming” in this section for Canadian residents. 4. The indicator light will flash slowly and then rapidly. Release both buttons when the indicator light flashes rapidly. (The rapid flashing light indicates acceptance of the hand-held transmitters’ radio frequency signals.) 5. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the light is constant, programming is complete and your device should activate when the HomeLink威 button is pressed and released. Note: To program the remaining two HomeLink威 buttons, begin with Step 2 in the “Programming” section — do not repeat Step 1. Note: If the indicator light blinks rapidly for two seconds and then turns to a continuous red, proceed with Steps 6 through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.)

56

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with Step 2 in the “Programming” section. For questions or comments, please contact HomeLink at www.homelink.com or 1–800–355–3515.

Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Steps 1 and 2
outlined in the “Programming” section, replace Step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink威 button (note Step 3 in the

“Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.

• Proceed with Step 4 in the “Programming” section.

57

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.

HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 2 in the “Programming” section. Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink威 button, follow Step 2 in the “Programming” section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

58

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime. Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • Odometer • Distance to Empty • Average Fuel Economy • Trip Odometer • Fuel Used • Trip Elapsed Drive Time • Compass Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display LOW FUEL LEVEL when you have approximately 20–25 miles (32–40 km) to empty. If you RESET this warning message, this display and tone will return within 10 minutes.

59

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

service stations

DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected. Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100
km. If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic shut-off points on the fuel pumps at • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings. For more information refer to Fuel Information in the Maintenance and Specifications chapter. Fuel Used Selecting this function from the INFO menu. XX.X G USED will display the fuel used since last reset. The information displayed will be in gallons or liters, depending on English/metric mode state.

60

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Trip elapsed drive time Select this function from the INFO menu to display a timer. To operate the Trip Elapsed Drive Time perform the following: 1. Press and release RESET in order to start the timer. 2. Press and release RESET to pause the timer. 3. Press and hold RESET for 2 seconds in order to reset the timer. Compass display Select this function from the INFO menu. Press the INFO button repeatedly until the Compass and Odometer are displayed. (Do not select Trip, DTE, or AFE. The top of the message center must be blank). The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone/calibration adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone/calibration adjustment. Compass zone/calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Turn ignition to the ON position. 2. Start the engine. 3. Press the INFO button repeatedly until the Compass and Odometer are displayed. (Do not select Trip, DTE, or AFE. The top of the message center must be blank).

61

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Note: If the compass displays ⬙CAL 000000.0 mi⬙ instead of heading information, the compass will need to be calibrated. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the ⬙CAL⬙ indicator changes to display compass heading. This may take up to 3 circles to complete calibration. 4. Determine your magnetic zone by referring to the zone map.

23

15

14
13
12

7 8 9 1011

5. Press and hold the RESET until the message center display changes to show the current zone setting.

6. Release the RESET control, then slowly press RESET down again. 7. Press the SETUP control repeatedly until the correct zone setting for your geographic location is displayed on the message center. To exit the zone setting mode press and release the RESET control. 8. Press the RESET control to start the compass calibration function.

9. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the SLOW CIRCLES TO CALIBRATE indicator changes to CALIBRATION COMPLETED. This will take up to three circles to complete calibration.

62

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

63

10. The compass is now calibrated. Setup menu Press this control for the following displays: • Language • Units (English/Metric) • System Check

Language 1. Select this function from the SETUP menu for the current language to be displayed.

2. Pressing the RESET control cycles the message center through each of the language choices.

3. Press and hold the RESET control to set the language choice.

Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric.

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for two to four seconds. Pressing the RESET control cycles the message center through each of the systems being monitored. The sequence of the system check report is as follows: 1. OIL LIFE 2. DOORS CLOSED 3. LIFTGATE/TRUNK CLOSED 4. ENGINE TEMP 5. CHARGING SYSTEM 6. BRAKE SYSTEM 7. PARK BRAKE STATUS 8. OIL PRESSURE 9. WASHER FLUID LEVEL 10. BRAKE FLUID LEVEL 11. COOLANT LEVEL 12. TRANSMISSION STATUS 13. TRACTION CONTROL (if equipped) 14. AWD SYSTEM (if equipped) 15. FUEL LEVEL System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for several seconds.

64

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages that have been reset are divided into three categories: • They will not disappear until a condition is changed. • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been

completed.

This acts as a reminder that these warning conditions still exist within the vehicle.

Status

Warning cannot be reset (CLOSE DOOR TO RESET) will be displayed

RELEASE PARK BRAKE will be displayed Warning returns after 10 minutes

Warnings

Driver’s door ajar Passenger door ajar Left rear door ajar Right rear door ajar Park brake engaged

Check engine temp Reduced engine power ETC-Engine failsafe mode AWD malfunction (if equipped) Check transmission Low fuel level Check fuel cap Check charging system Oil pressure low Check brake system

65

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Warnings

Status

Warning returns after the ignition key is turned from OFF to RUN

Low brake fluid Liftgate ajar (if equipped) Trunk ajar (if equipped) Check Traction Control (if equipped) Washer Fluid level low Coolant level low Check engine Change oil soon Oil change required Data error DRIVER’S DOOR AJAR. Displayed when the driver’s door is not completely closed. PASSENGER DOOR AJAR. Displayed when the passenger side door is not completely closed. LEFT REAR DOOR AJAR. Displayed when the left rear door is not completely closed. RIGHT REAR DOOR AJAR. Displayed when the right rear door is not completely closed. PARK BRAKE ENGAGED. Displayed when the park brake is engaged. If the warning stays on after the park brake is off, contact your dealer as soon as possible. CHECK ENGINE TEMPERATURE. Displayed when the engine coolant is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your dealer as soon as possible. REDUCED ENGINE POWER. Displayed when the engine is overheating. Stop the vehicle as soon as safely possible, turn off the engine. If the warning stays on or continues to come on, contact your dealer as soon as safely possible. ETC-ENGINE FAILSAFE MODE. Displayed when the engine has defaulted to a “limp-home” operation. If the warning stays on or continues to come on, contact your dealer as soon as possible.

66

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

AWD MALFUNCTION (if equipped). Displayed when the AWD system is not operating properly. If the warning stays on or continues to come on, contact your dealer immediately. CHECK TRANSMISSION. Indicates the transmission is not operating properly, contact your dealer as soon as possible. LOW FUEL LEVEL. Displayed as an early reminder of a low fuel condition. CHECK FUEL CAP. Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap for proper installation. Refer to Fuel filler cap in the Maintenance and Specifications chapter. CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible. OIL PRESSURE LOW. Displayed when the engine oil level is low. If this warning message is displayed, check the level of the engine oil. Refer to Engine oil in the Maintenance and Specifications chapter for information about adding engine oil. CHECK BRAKE SYSTEM. Displayed when the brake system needs servicing. If the warning stays on or continues to come on, contact your dealer as soon as possible. LOW BRAKE FLUID. Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid reservoir in the Maintenance and Specifications chapter. LIFTGATE AJAR (if equipped). Displayed when the liftgate is not completely closed. TRUNK AJAR (if equipped). Displayed when the trunk is not completely closed. CHECK TRACTION CONTROL (if equipped). Displayed when the Traction Control娂 system is not operating properly. If this warning stays on, contact your dealer for service as soon as possible. For further information, refer to Traction control娂 in the Driving chapter. LOW WASHER FLUID LEVEL. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter.

67

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

COOLANT LEVEL LOW. Displayed when the engine coolant is low. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your dealer as soon as possible. CHECK ENGINE. Indicates the engine is not operating properly. If this warning stays on, contact your dealer as soon as possible. CHANGE OIL SOON/OIL CHANGE REQUIRED. Oil Life XX%, CHANGE SOON/OIL LIFE 0%, CHANGE OIL, OIL LIFE XX%, CHANGE SOON displayed when the engine oil life remaining is 10 percent and again when the engine oil life remaining is between 5% and 1%. When oil life left reaches 0%, the OIL LIFE 0%, CHANGE OIL message will be displayed. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: 1. Select this function from the SETUP control for current display mode.

2. Press and release the RESET control to display “HOLD RESET TO CONFIRM”.

3. Press and hold the RESET control to display OIL LIFE SET TO 100%. Your oil life is now reset.

To reset the oil monitoring system to your personalized oil life %:

68

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

1. From step 3 above.

Driver Controls

2. Release the RESET control momentarily, then press RESET and SETUP controls at the same time to activate a service mode which will display OIL LIFE XX% RESET TO ALTER. 3. Press RESET until you find your personalized OIL LIFE XX%. 4. With your personalized OIL LIFE XX% displayed, press SETUP to continue the system check. DATA ERR. These messages indicate improper operation of the vehicle network communication between electronic modules. • Fuel computer • Charging system • Coolant system • Traction control (if equipped) • Door sensor • Brake fluid • Compass (if equipped) • Outside temperature (if equipped) • Engine sensor • Transmission control module (TCM) • Fuel cap sensor • Seat belt sensor • Park brake • Oil pressure sensor Contact your dealer as soon as possible if these messages occur on a regular basis.

69

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • Utility compartment with power • Gear Shift • Cup holders • Rear vent (if equipped)

point

Use only soft cups in the cupholder. Hard objects can injure you in a collision.

CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits. Mobile Communication Equipment includes, but is not limited to cellular phones, pagers, portable email devices, in-vehicle communications systems, telematics devices and portable two-way radios.

A driver’s first responsibility is the safe operation of the vehicle. The most important thing you can do to prevent a crash is to

avoid distractions and pay attention to the road. Wait until it is safe to operate Mobile Communications Equipment.

70

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

INTERIOR TRUNK CONTROL Press the remote trunk release control on the instrument panel to the left of the steering wheel.

CARGO AREA FEATURES

Cargo net (if equipped) The cargo net secures lightweight objects in the cargo area. Attach the net to the anchors provided. Do not put more than 50 lbs. (22 kg) in the net.

This net is not designed to restrain objects during a

collision.

71

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized dealer. Refer to the SecuriLock娂 passive anti-theft system section later in this chapter for more information.

POWER DOOR LOCKS Press control to unlock or lock all doors.

Smart locks This feature attempts to help prevent you from locking yourself out of the vehicle if your key is still in the ignition. When you open the driver’s door and you lock the vehicle with the power door lock control (on the driver or passenger door trim panel), all the doors will lock, then the driver’s door will automatically unlock reminding you that your key is still in the ignition. The vehicle can still be locked, with the key in the ignition, using the manual lock control on the door, locking the driver’s door with a key, or using the lock control on the remote entry transmitter. If the driver’s door is closed, then the vehicle can be locked from any method, regardless of whether the key is in the ignition or not.

Power door lock/unlock inhibit feature As a theft deterrent, the power door lock controls can be disabled 20
seconds after the ignition has been turned to the 1 (LOCK) position and the vehicle is locked using the remote entry transmitter or the key in the door lock cylinder. The door lock controls are re-enabled when the vehicle is unlocked using the key in the door lock cylinder, the keypad (if equipped) or by pressing on the remote entry transmitter. This feature can be turned on or off using the following procedure: Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle doors are closed. You must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated.

72

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

1. Place the key in the ignition and turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back to the 3 (RUN) position. The horn will chirp one time to confirm programming mode has been entered and is active. 6. Press the power door lock control on the door panel two times within five seconds. The horn will chirp two times to confirm the feature is off; the horn will chirp two times and honk one time to confirm the feature is on. 7. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. The horn will chirp one time to confirm the programming mode has been exited. Repeat the procedure to turn the feature on or off.

Childproof door locks • Move control up to engage the • Move control down to disengage

childproof lock.

childproof lock.

The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • When the childproof door locks are set, the rear doors cannot be • The rear doors can be opened from the outside when the power door

opened from the inside.

locks are unlocked.

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment.

73

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Adults are advised to familiarize themselves with the operation and location of the release handle. To open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light. The “T” shaped handle will be located either on the luggage compartment door (lid) or inside the luggage compartment near the tail lamps.

Keep vehicle doors and luggage compartment

locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the trunk and risk injury. Children should be taught not to play in vehicles.

On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people or animals to these high

temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.

74

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. The remote entry system allows you to: • unlock the vehicle doors without • lock all the vehicle doors without • open the trunk without a key. • activate the personal alarm. • arm and disarm the perimeter • operate the illuminated entry

anti-theft system.

a key.

a key.

feature.

The remote entry lock/unlock feature operates in any ignition position. The panic feature operates with the key in the 1 (LOCK) or 2 (ACC) position. If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the dealership in order to aid in troubleshooting the problem.

Unlocking the doors 1. Press lamps will illuminate.

and release to unlock the driver’s door. Note: The interior

75

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

and release again within three seconds to unlock all the

2. Press doors. The remote entry system activates the illuminated entry feature; this feature turns on the lamps for 25 seconds or until the ignition is turned to the 3 (RUN) position. The inside lights will not turn off if: • they have been turned on using the dimmer control or • any door is open. The battery saver feature will turn off the interior lamps 30 minutes after the ignition is turned to the 1 (LOCK) position.

and release to lock all the doors. The turn lamps will flash.

Locking the doors 1. Press Note: If any door is not closed properly, the lamps will not flash. 2. Press and release again within three seconds to confirm that all the doors are closed. Note: The doors will lock again, the horn will chirp and the turn lamps will flash once if all the doors and trunk are closed. If any door or the trunk is not closed, or if the hood is not closed in vehicles equipped with the perimeter alarm feature, the horn will chirp twice and the lamps will not flash

Sounding a panic alarm to activate the alarm. The horn will sound and the turn lamps Press will flash for a maximum of 3 minutes. Press again or turn the ignition to the 3 (RUN) position to deactivate, or wait for the alarm to timeout in 3
minutes. Note: The panic alarm will only operate when the ignition is in the 1
(LOCK) or 2 (ACC) position.

Opening the trunk Press • Ensure that the trunk is closed and latched before driving your

once to open the trunk.

vehicle. Failure to properly latch the trunk may cause objects to fall out or block the driver’s rear view.

Memory seats/power mirrors/adjustable pedals (if equipped) The remote entry system can also control the memory seat /power mirrors/adjustable pedals feature.

76

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Press to automatically move the seat, mirrors and adjustable pedals to the desired memory position (the positions correspond to the transmitter being used). For more information on programming the transmitters to Driver 1 and Driver 2 memory positions, refer to How to reprogram your remote entry transmitters later in this chapter. Activating the memory seat feature To activate this feature: 1. Position the seat, mirrors and adjustable pedals to the position desired. 2. Press the SET control on the driver’s door panel. 3. Within 5 five seconds, press the 1
or 2 control on the driver’s door panel to which you would like to associate with the seat, mirrors and adjustable pedals and Driver 1 or Driver 2 positions. 4. Repeat this procedure for the other Driver position if desired.

Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.

77

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. To reprogram the remote entry transmitters:

1. Ensure the vehicle is electronically unlocked.

78

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

2. Put the key in the ignition. 3. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (RUN). Note: The eighth turn must end in the 3 (RUN) position. 4. The doors will lock, then unlock, to confirm that the programming mode has been activated. 5. Within 20 seconds press any button on the remote entry transmitter to be programmed. Note: If more than 20 seconds have passed you will need to start the procedure over again. 6. The doors will lock, then unlock, to confirm that each remote entry transmitter has been programmed. 7. Repeat Step 5 to program each additional remote entry transmitter. Note: The first remote transmitter programmed corresponds to Driver 1; the second, Driver 2. 8. Turn the ignition to the 1 (LOCK) position after you have finished programming all of the remote entry transmitters. Note: If any one of the transmitters is not reprogrammed, it will be erased. 9. The doors will lock, then unlock, to confirm that the programming mode has been exited.

Illuminated entry The interior lamps illuminate when the remote entry system, the keyless entry system keypad (if equipped) or the door lock cylinder (on vehicles equipped with the perimeter alarm system) is used to unlock the door(s). The illuminated entry system will turn off the interior lights if: • the ignition is turned to the 3 (RUN) position, or • the remote transmitter lock control is pressed, or • after 25 seconds of illumination. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Battery saver The battery saver will shut off the interior lamps 30 minutes after the ignition has been turned to the 1 (LOCK) position. • If the dome lamps were turned on using the panel dimmer control, the

battery saver will shut off them off 30 minutes after the ignition has been turned to the 1 (LOCK) position.

79

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security • If the courtesy lamps were turned on because one of the vehicle doors was opened, the battery saver will shut them off 10 minutes after the ignition has been turned to the 1 (LOCK) position.

• The battery saver will shut off the headlamps and foglamps 10

minutes after the ignition has been turned to the 1 (LOCK) position.

Illuminated exit • When all vehicle doors and the trunk are closed, and the key is

removed from the ignition, the interior dome lamps (and the exterior mirror puddle lamps, if equipped) will illuminate.

The lights will turn off if all the doors and the trunk remain closed and • 25 seconds elapse, or • the key is inserted in the ignition. KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to: • lock or unlock the doors without • open the trunk. • recall memory seat/power mirrors/adjustable pedals positions 1 or 2.

using a key.

The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5–digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.

Programming a personal entry code and keypad association to memory seats, mirrors and pedals To create your own personal entry code: 1. Enter the factory set code.

80

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. 4. To associate the entry code with a memory setting, enter a sixth digit to indicate which driver should be set in a memory recalled by the personal entry code: • Pressing 1 • 2 recalls Driver 1 settings. • Pressing 3 • 4 recalls Driver 2 settings. • Pressing other keypad buttons or not pressing a keypad button as a sixth digit does not set a driver and will not recall a memory setting. Note: The factory-set code cannot be associated with a memory setting.

5. The doors will again lock then unlock to confirm that your personal keycode has been programmed to the module. Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal

code.

Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. Your personal code is now erased and only the factory set 5–digit code will work.

Anti-scan feature If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after: • one minute of keypad inactivity. • pressing the UNLOCK • the ignition is turned to the 3 (RUN) position.

control on the remote entry transmitter.

81

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. The interior lamps will illuminate. To unlock all doors, enter the factory set code or your personal code, then press the 3 • 4 control within five seconds. To open the trunk, enter the factory set code or your personal code, then press the 5 • 6 control within five seconds. To lock all doors, press the 7 • 8 and the 9 • 0 at the same time. You do not need to enter the keypad code first.

Autolock The autolock feature will lock all the doors when: • all the doors are closed, • the ignition is in the 3 (RUN) position, • you shift into any gear putting the vehicle in motion, and • the brake pedal is released and the vehicle attains a speed greater

than 5 mph (8 km/h).

The autolock feature repeats when: • any door is opened then closed while the ignition is in the 3 (RUN) • you put the vehicle in motion by releasing the brake pedal and the

position, and

vehicle attains a speed greater than 5 mph (8 km/h).

Deactivating/activating autolock Your vehicle comes with the autolock feature activated. There are three methods to enable/disable this feature: One is through your dealer, the second with a power door unlock/lock sequence, and the third with the keypad. Before following the activation or deactivation procedures, make sure that the anti-theft system is not armed, ignition is off, and all vehicle doors are closed.

82

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Power door unlock/lock procedure You must complete steps 1-5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. Turn the ignition to the 3 (RUN) position. 2. Press the power door unlock control three times. 3. Turn the ignition from the 3 (RUN) to the 1 (LOCK) position. 4. Press the power door unlock control three times. 5. Turn the ignition back to the 3 (RUN) position. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to the 1 (LOCK) position. The horn will chirp once to confirm the procedure is complete. Keyless entry key pad procedure 1. Turn the ignition to the 1 (LOCK) position. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Press and hold the 7 • 8. While holding the 7 • 8 press the 3 • 4. 5. Release the 3 • 4. 6. Release the 7 • 8. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled.

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded keys; additional coded keys may be purchased from your dealer. The dealer can program your spare keys to your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key.

83

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Note: The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded key and restart the engine.

Theft indicator The theft indicator is located in the instrument panel cluster. • When the ignition is in the 1
(LOCK) position, the indicator will flash once every 2 seconds to indicate the SecuriLock娂 system is functioning as a theft deterrent.

• When the ignition is in the 3 (RUN) position, the indicator will glow

for 3 seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (RUN) position. If this occurs, the vehicle will not start and should be taken to an authorized dealer for service.

Automatic arming The vehicle is armed immediately after switching the ignition to the 1
(LOCK) position. The theft indicator will flash every two seconds to act as a theft deterrent when the vehicle is armed.

Automatic disarming The vehicle is disarmed immediately after the ignition is turned from the 1 (LOCK) to the 3 (RUN) position. The theft indicator will illuminate for three seconds and then go out. If the theft indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your dealer.

84

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to a dealership. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.

Programming spare keys You can program your own coded keys to your vehicle. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use SecuriLock娂 keys. • You must have two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible.

• If two previously programmed coded keys are not available, you must

take your vehicle to your dealer to have the spare key(s) programmed.

Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition.

2. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds, but no more than 10 seconds. 3. Turn the ignition to the 1 (LOCK) position and remove the first coded key from the ignition. 4. Within ten seconds of turning the ignition to the 1 (LOCK) position, insert the second previously coded key into the ignition. 5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds, but no more than 10 seconds.

85

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

6. Turn the ignition to the 1 (LOCK) position and remove the second previously programmed coded key from the ignition. 7. Within twenty seconds of turning the ignition to the 1 (LOCK) position and removing the previously programmed coded key, insert the new unprogrammed key (new key/valet key) into the ignition. 8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds but not more than 10 seconds. 9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’s engine and the theft indicator light will flash on and off. Wait 20
seconds and you may repeat Steps 1 through 8. If failure repeats, bring your vehicle to your dealer to have the new key(s) programmed. To program additional new unprogrammed key(s), wait twenty seconds and then repeat this procedure from Step 1.

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help prevent your vehicle from unauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are brought to the dealership, to aid in troubleshooting.

Arming the system When armed, this system will respond if unauthorized entry is attempted. When unauthorized entry occurs, the system will flash the turn signal lamps and will sound the horn. The system is ready to arm whenever the key is removed from the ignition. Either of the following actions will prearm the alarm system: • Press the When you press the lock control twice within three seconds on your remote entry transmitter, the horn will chirp once to let you know that all doors, the hood and the trunk are closed. If any of these are not closed, the horn will chirp twice to warn you that a door, the hood or the trunk is still open.

control on the remote entry transmitter.

86

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

• Press the driver or passenger interior door lock control while the door is open, then close the door.

• Press the 7 • 8 and 9 • 0

controls on the keyless entry pad at the same time to lock the doors (driver’s door must be closed).

There is a 20 second countdown when any of the above actions occur before the vehicle becomes armed. Each door, the hood or the trunk is armed individually, and if any are open, they must be closed for the system to enter the 20 second countdown. The turn signal lamps will flash once when all doors, the hood or the trunk are closed indicating the vehicle is locked and entering the 20
second countdown. Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter. • Unlock the doors by using your keyless entry pad. • Unlock the driver’s door with a key. Turn the key full forward (toward • Turn ignition to the 3 (ON) position. • Press the panic control on the remote entry transmitter. This will only shut off the horn and parking lamps when the alarm is sounding. The alarm system will still be armed.

the front of the vehicle) to make sure the alarm disarms.

Pressing the power door UNLOCK control within the 20 second prearmed mode will return the vehicle to a disarmed state. Triggering the anti-theft system The armed system will be triggered if: • Any door, the hood or the trunk is opened without using the door key,

keypad or the remote entry transmitter.

87

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

SEATING Notes:

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.

Adjustable head restraints Head restraints help to limit head motion in the event of a rear collision. Adjust your head restraint so that it is located directly or as close as possible behind your head. The head restraints can be moved up by pulling up on the head restraint.

Push release button to lower head restraint.

88

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Using the manual lumbar support (if equipped) The lumbar support control is located on the outboard side of the seatback. Move the control up or down to adjust lumbar support.

Folding down the front passenger seatback (if equipped) The front passenger seatback can be folded to a horizontal position to make room for a long load. To fold the seatback: 1. Move the seat as far back as possible. 2. Push the head restraint release button and move the head restraint fully down. 3. Pull the strap located on the back of the seat to fold the front passenger seatback. 4. Without releasing the pull strap, push the seatback forward. 5. Move the seat as far forward as possible.

Cover sharp edges on the load to help prevent injury to occupants. Secure the load to help prevent shifting during

sudden stops.

Ensure that the seatback is latched by pushing and pulling on it. If not latched, the seat may cause injury during a sudden stop.

89

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the

seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.

Adjusting the front manual seat (if equipped)

Never adjust the driver’s seat or seatback when the vehicle is moving.

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

Lift handle to move seat forward or backward.

Pull lever up to adjust seatback.

Adjusting the front power seat (if equipped)

Never adjust the driver’s seat or seatback when the vehicle is moving.

90

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

The control is located on the outboard side of the seat cushion. Press the front or rear portion to tilt the seat. • Driver

Press the control to move the seat forward, backward, up or down. • Driver

Press the control to move the seat forward, or backward. • Passenger

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

91

Seating and Safety Restraints

Press the control (if equipped) to recline the seatback forward or rearward.

Heated seats (if equipped) To operate the heated seats: • Push the control located on the

climate control system panel once to activate high heat. • Push twice to activate low heat. • Push a third time to deactivate. The indicator light on the control will illuminate when activated. For low heat, 1 light will be lit; for high heat, both lights will be lit. The heating of the seat turns off after 10 minutes or when the vehicle is turned off. Memory seats/sideview mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to two programmable positions. The memory seat control is located on the driver door. • To program position 1, move the driver seat, mirrors and pedals (if equipped) to the desired position using the associated controls. Press the SET control. The SET control indicator light will briefly illuminate. While the light is illuminated, press control 1.

• To program position 2, repeat the previous procedure using control 2. A position can be recalled:

92

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

• in any gearshift position if the ignition is not in the RUN position. • only in Park or Neutral if the ignition is in the RUN position. A memory seat position may be programmed at any time. The memory positions are also recalled when you press your remote entry transmitter UNLOCK control if the transmitter is programmed to a memory position or when you enter a valid personal entry code that is programmed to a memory position. To program the memory feature to a remote entry transmitter and for more information on how to use the keypad, refer to Remote entry system in the Locks and Security chapter. REAR SEATS

Head restraints Lift the head restraint so that it is located directly or as close as possible behind your head. The head restraints can be moved up by pulling up on the head restraint.

Push release button to lower head restraint.

Split-folding rear seat One or both rear seatbacks can be folded down to provide additional cargo space.

93

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

To lower the seatback(s) from inside the vehicle, pull the strap located on the outboard side of the seatback to release it, and then fold seatback down.

When raising the seatback(s), make sure you hear the seat latch into place.

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the

seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.

Seat mounted cup holders and armrest storage compartment (if equipped)

Your vehicle is equipped with cup holders and a storage compartment (if equipped) in the rear seat armrest. To access the cup holders, rotate armrest into use position. To open the storage compartment (if equipped), pull up on the latch.

Use only soft cups in the cupholder. Hard objects can injure you in a collision.

94

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

SAFETY RESTRAINTS

Personal Safety System姟 The Personal Safety System娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations. Your vehicle’s Personal Safety System娂 consists of: • Driver and passenger dual-stage airbag supplemental restraints. • Front safety belts with pretensioners, energy management retractors • Driver’s seat position sensor. • Passenger occupant classification sensor • Front crash severity sensor. • Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and back-up tone. • The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, passenger occupant classification sensor, and indicator lights.

(first row only), and safety belt usage sensors.

How does the Personal Safety System姟 work? The Personal Safety System娂 can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints Control Module (RCM). During a crash, the RCM activates the safety belt pretensioners and/or either one or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant conditions. The fact that the pretensioners or airbags did not activate for both front seat occupants in a collision does not mean that something is wrong with the system. Rather, it means the Personal Safety System娂 determined the accident conditions (crash severity, belt usage, etc.) were not appropriate to activate these safety devices. Front airbags are designed to activate only in frontal and near-frontal collisions (not rollovers, side impacts or rear impacts) unless the collision causes sufficient longitudinal deceleration. The pretensioners are designed to activate in frontal and near-frontal collisions, and in side collisions and rollovers when the vehicle is equipped with the Safety Canopy娂 system.

95

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbag inflation energy. A lower, less forceful energy level is provided for more common, moderate-severity impacts. A higher energy level is used for the most severe impacts. Refer to Airbag supplemental restraints section in this chapter. Front crash severity sensor The front crash severity sensor enhances the ability to detect the severity of an impact. Positioned up front, it provides valuable information early in the crash event on the severity of the impact. This allows your Personal Safety System娂 to distinguish between different levels of crash severity and modify the deployment strategy of the dual-stage airbags and safety belt pretensioners. Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System娂 to tailor the deployment level of the driver dual-stage airbag based on seat position. The system is designed to help protect smaller drivers sitting close to the driver airbag by providing a lower airbag output level. Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, this occurs because they are initially sitting very close to the airbag. For other occupants, this occurs when the occupant is not properly restrained by seat belts or child safety seats and they move forward during pre-crash braking. The most effective way to reduce the risk of unnecessary injuries is to make sure all occupants are properly restrained. Accident statistics suggest that children are much safer when properly restrained in the rear seating positions than in the front.

Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must

use a forward-facing child seat in the front seat, move the seat all the way back.

96

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.

The passenger occupant classification sensor can automatically turn off the passenger front airbag. The system is designed to help protect small (child size) occupants from airbag deployments when they are improperly seated or restrained in the front passenger seat contrary to proper child-seating or restraint usage recommendations. Even with this technology, parents are STRONGLY encouraged to always properly restrain children in the rear seat. The sensor also turns off the passenger front airbag and seat-mounted side airbag (if equipped) when the passenger seat is empty to prevent unnecessary replacement of airbag(s) after a collision. Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Personal Safety System娂 to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage. Refer to Safety belt section in this chapter. Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’s body during frontal collisions, and in side collisions and rollovers when the vehicle is equipped with the Safety Canopy娂 system. This maximizes the effectiveness of the safety belts. In frontal collisions, the safety belt pretensioners can be activated alone or, if the collision is of sufficient severity, together with the front airbags. Front safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’s forward momentum. This helps reduce the risk of force-related injuries to the occupant’s chest by limiting the load on the occupant. Refer to Energy management feature section in this chapter. Determining if the Personal Safety System姟 is operational The Personal Safety System娂 uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the Warning light section in the Instrument Cluster chapter. Routine maintenance of the Personal Safety System娂 is not required.

97

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

The Restraints Control Module (RCM) monitors its own internal circuits and the circuits for the airbag supplemental restraints, crash sensor(s), safety belt pretensioners, front safety belt buckle sensors, driver seat position sensor, and passenger occupant classification sensor. In addition, the RCM also monitors the restraints warning light in the instrument cluster. A difficulty with the system is indicated by one or more of the following. • The warning light will either flash or stay lit. • The warning light will not illuminate immediately after ignition is • A series of five beeps will be heard. The tone pattern will repeat

turned on.

periodically until the problem and warning light are repaired.

If any of these things happen, even intermittently, have the Personal Safety System娂 serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision. Safety belt precautions

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

To reduce the risk of injury, make sure children sit where they can be properly restrained.

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from

injury in a collision.

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag

supplemental restraint system (SRS) is provided.

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas

are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.

98

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.

Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that

are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.

2. To unfasten, push the release button and remove the tongue from the buckle.

99

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

All restraints in the vehicle are combination lap and shoulder belts. While you are fastened in the seat belt, the combination lap/shoulder belt adjusts to your movement. However, if you brake hard, turn hard, or if your vehicle receives an impact of 5 mph (8 km/h) or more, the safety belt will become locked and help reduce your forward movement.

Energy Management Feature — Outboard • This vehicle has a safety belt system with an energy management

feature at the front seats to help further reduce the risk of injury in the event of a head-on collision. • This safety belt system has a retractor assembly that is designed to

extend the seat belt webbing in a controlled manner. This helps reduce the belt force acting on the user’s chest.

Failure to inspect and replace if necessary the Belt and Retractor assembly after an accident could increase the risk of

injury in a collision.

Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 5 mph (8
km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. Automatic locking mode

When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. This mode should be used any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter.

100

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

How to use the automatic locking mode • Buckle the combination lap and

shoulder belt.

• Grasp the shoulder portion and pull downward until the entire belt is pulled out.

• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.

How to disengage the automatic locking mode

Ford Motor Company recommends that all passenger safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision to verify that the ⬙automatic locking retractor⬙ feature for child seats is still working properly. Safety belt assemblies should be inspected according to the procedures in the Workshop Manual and must be replaced if either damage or improper operation is noted. Failure to replace the belt and retractor assembly could increase the risk of injury in a collision.

Unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.

101

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Safety belt height adjustment Your vehicle has safety belt height adjustments for the front outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To adjust the shoulder belt height, squeeze the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place.

Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety

belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.

Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.

102

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position...

Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.

The safety belt warning light and warning chime turn off.

The safety belt warning light and indicator chime remain off.

BeltMinder姟 Note: If your vehicle is built without the passenger occupant classification sensor, the passenger BeltMinder娂 feature is not available. The BeltMinder娂 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster when the driver’s and front passenger’s safety belt is unbuckled. The BeltMinder娂 feature uses information from the passenger occupant classification sensor to determine if a front seat passenger is present and therefore potentially in need of a warning. To avoid activating the BeltMinder娂 feature for objects placed in the front passenger seat, warnings will only be given to large front seat occupants as determined by the passenger occupant classification sensor. Both the driver’s and passenger’s safety belt usages are monitored and either may activate the BeltMinder娂 feature. The warnings are the same for the driver and the front passenger. If the BeltMinder娂 warnings have expired (warnings for approximately 5 minutes) for one occupant (driver or front passenger), the other occupant can still activate the BeltMinder娂 feature.

103

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

If... The driver’s and front passenger’s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2
minutes have elapsed since the ignition switch has been turned ON... The driver’s or front passenger’s safety belt is not buckled when the vehicle has reached at least 3 mph (5
km/h) and 1-2 minutes have elapsed since the ignition switch has been turned to ON... The driver’s or front passenger’s safety belt becomes unbuckled for approximately 1
minute while the vehicle is traveling at least 3 mph (5
km/h) and more than 1-2
minutes have elapsed since the ignition switch has been turned to ON...

Then... The BeltMinder娂 feature will not activate.

The BeltMinder娂 feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30
seconds, repeating for approximately 5 minutes or until the safety belts are buckled.

The BeltMinder娂 feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30
seconds, repeating for approximately 5 minutes or until the safety belts are buckled.

104

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... “Crashes are rare events”

Consider... 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. 3 of 4 fatal crashes occur within 25
miles (40 km) of home. We design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. Prime time for an accident. BeltMinder娂 reminds us to take a few seconds to buckle up. Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4
times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see.

“I’m not going far”

“Belts are uncomfortable”

“I was in a hurry”

“Safety belts don’t work”

“Traffic is light”

“Belts wrinkle my clothes”

“The people I’m with don’t wear belts”

105

2005 Five Hundred (500) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Reasons given... “I have an airbag”

“I’d rather be thrown clear”

Consider... Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”.

Do not sit on top of a buckled safety belt to avoid the BeltMinder娂 chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the BeltMinder娂 feature please follow the directions stated below.

One time disable If at any time the driver/front passenger quickly buckles then unbuckles the BeltMinder娂 feature for that seating position, the BeltMinder娂 is disabled for the current ignition cycle. The BeltMinder娂 feature will re-enable during the same ignition cycle if the occupant buckles and remains buckled for approximately 30 seconds. Confirmation is not given for the one time disable. Deactivating/activating the BeltMinder姟 feature The driver and front passenger BeltMinder娂 are deactivated/activated independently. When deactivating/activating one seating position, do not buckle the other position as this will terminate the process. Read Steps 1 - 4 thoroughly before proceeding with the deactivation/activation programming procedure. Note: The driver and front passenger BeltMinder娂 features must be disabled/enabled separately. Both cannot be disable/enabled during the same key cycle.

106