Download PDF Manual

USA (fus)


Locks and Security


pressed, or


Illuminated entry The interior lamps and parking lamps illuminate when the remote entry system is used to unlock the door(s). The illuminated entry system will turn off the lights if: • the ignition switch is turned to the on position, or • the remote transmitter lock control is pressed, or • the 7 • 8 and the 9 • 0 controls on the keyless entry keypad are • after 25 seconds of illumination. The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the ignition has been turned to the off position, 10 minutes after if the dome lamp is off, and 30 minutes after if the dome lamp switch is left on.


icon, you have remote start. The remote start feature has an


Remote start (if equipped) Your vehicle may be equipped with the remote start feature which allows you to start the engine from outside the vehicle. If your transmitter has extended operating range which allows you to remote start your vehicle from a farther distance from your vehicle. All the buttons have this increased range performance capability when equipped with remote start. Many states and provinces have restrictions for the use of remote start. Check your local and state or provincial laws for specific requirements regarding remote start systems. Note: Do not use remote start if your vehicle is low on fuel.


WARNING: To avoid exhaust fumes, do not use remote start if your vehicle is parked indoors or areas that are not well


ventilated.


154


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Locks and Security


hour.


The remote start system will not work if: • The ignition is in the on position. • The alarm system is triggered. • The feature has been disabled. • The hood is not closed. • Two remote vehicle starts have already been attempted within the last • The vehicle is not in P (Park). Starting the engine with remote start To start the engine using remote start: Note: Each button press must be done within 3 seconds of each other. If this sequence is not followed the vehicle will not remote start and the horn will not chirp. 1. Press 2. Press


on the IKT to lock all the doors. two times. The exterior lamps will flash twice.


If for some reason, the system fails to start, the horn will chirp twice.


3. Insert the key in the ignition and turn to the on position before driving. The power windows will be inhibited during the remote start and the radio will not turn on. The parking lamps will remain on and the engine will run for 5, 10, or 15 minutes, depending on how you programmed the system. To select the duration of the remote start system refer to Message center in the Instrument Cluster chapter. Extending the engine run time To keep the engine running for another remote start duration, repeat Steps 1 and 2 with the engine still running. If you programmed the duration to last 10 minutes, the second 10 minutes will begin immediately so that, for example, if the vehicle had been running from the first remote start for five minutes, the engine will continue to run for a total of 15 minutes. You can only extend the remote start once. If the vehicle is remote started then remote stopped, wait at least five seconds before remote starting a second time. The ignition switch must be turned to the on position and then back to the off position or allow one hour to pass before using remote start again.


155


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Locks and Security


Turning the engine off after using remote start • Press


one time. The parking lamps will turn off.


You may have to be closer to the vehicle than when starting due to ground reflection and the added noise of the running engine.


You can disable or enable the remote start system through the message center. Refer to Message center in the Instrument Cluster chapter.


SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to lock or unlock the doors without using a key. The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5–digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.


Programming a personal entry code and keypad association to memory feature To create your own personal entry code: 1. Enter the factory set code. 2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. 4. To associate the entry code with a memory setting, enter a sixth digit to indicate which driver should be set in a memory recalled by the personal entry code: • Pressing 1 • 2 recalls Driver 1 settings. • Pressing 3 • 4 recalls Driver 2 settings. • Pressing other keypad buttons or not pressing a keypad button as a sixth digit does not set a driver and will not recall a memory setting. Note: The factory-set code cannot be associated with a memory setting.


5. The doors will again lock then unlock to confirm that your personal entry code has been programmed to the module. 156


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Locks and Security


Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal


code.


Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. Your personal code is now erased and only the factory set 5–digit code will work.


control on the remote entry transmitter.


Anti-scan feature If an incorrect code has been entered seven times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash during this time. The anti-scan feature will turn off after: • one minute of keypad inactivity. • pressing the • the ignition is turned to the on position. Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. The interior lamps will illuminate after entering a valid keypad entry code. To unlock all doors, press the 3 • 4 control within five seconds. To lock all doors, press the 7 • 8 and the 9 • 0 at the same time. You do not need to enter the keypad code first. Note: The interior lamps will turn off.


157


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Locks and Security


SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) SecuriLock威 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. The message center will display: STARTING SYSTEM FAULT. Your vehicle comes with two coded keys; additional coded keys may be purchased from your authorized dealer. The authorized dealer can program your spare keys to your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The SecuriLock威 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded key and restart the engine. Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle.


Automatic arming The vehicle is armed immediately after turning the ignition off.


Automatic disarming Switching the ignition on with a coded key disarms the vehicle.


Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys. 158


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Locks and Security


Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock威 keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure. If two previously programmed coded keys are not available, you must bring your vehicle to your authorized dealer to have the spare coded key(s) programmed. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition and turn the ignition from the 1 (off) position to the 3 (on) position (maintain ignition in the 3
(on) position for at least one second, but no more than 10 seconds). 2. Turn ignition from the 3 (on) position back to the 1 (off) position in order to remove the first coded key from the ignition. 3. After three seconds but within 10 seconds of removing the first coded key, insert the second previously programmed coded key into the ignition and turn the ignition from the 1 (off) position to the 3 (on) position (maintain ignition in the 3 (on) position for at least one second but no more than 10 seconds). 4. Turn the ignition from the 3 (on) position back to the 1 (off) position in order to remove the second coded key from the ignition. 5. After three seconds but within 10 seconds of removing the second coded key, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from the 1 (off) position to the 3 (on) position (maintain ignition in the 3 (on) position for at least one second, but no more than 10 seconds). This step will program your new key to a coded key. 6. To program additional new unprogrammed key(s), repeat Steps 1
through 5. If successful, the new coded key(s) will start the vehicle’s engine.


159


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Locks and Security


If not successful, the new coded key(s) will not start the vehicle’s engine and you may repeat Steps 1 through 5. If failure repeats, bring your vehicle to your authorized dealer to have the new spare key(s) programmed.


PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn you in the event of an unauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL remote entry transmitters are taken to the authorized dealer to aid in troubleshooting.


Arming the system When armed, this system will respond if unauthorized entry is attempted. When unauthorized entry occurs, the system will flash the park/turn lamps and will sound the horn. The system is ready to arm whenever the key is removed from the ignition. Either of the following actions will prearm the alarm system: • Press the • Open a door and press the power door lock control to lock all the • Press and hold the 7 • 8 and 9 • 0 controls on the keyless entry pad


control on the remote entry transmitter.


doors, and then close the door.


at the same time to lock the doors (driver’s door must be closed).


There is a 20 second countdown when any of the above actions occur before the vehicle becomes armed. Each door and the hood is armed individually, and if any are open, they must be closed before the open entry point can enter the 20 second countdown. The turn signal lamps will flash once when all doors and the hood are closed indicating the vehicle is locked and entering the 20 second countdown.


160


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Locks and Security


transmitter.


Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by pressing the • Turn the ignition to the on position with a programmed coded ignition • Unlock the doors by using your keyless entry pad. • If using a key in the driver’s door to unlock the vehicle, a chime will


control on your remote entry


key.


sound when you open the door and you will have 12 seconds to disarm the alarm system using any of the actions above, otherwise the alarm will trigger.


Pressing the power door unlock control within the 20 second prearmed mode will return the vehicle to a disarmed state. Triggering the anti-theft system The armed system will be triggered if any door or hood is opened without using the key or the remote entry transmitter.


161


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


FRONT SEATS


WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal


injuries in the event of a collision.


WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.


WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped


behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.


WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving.


WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


Adjustable head restraints Your vehicle is equipped with front row outboard head restraints that are vertically adjustable.


WARNING: To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion.


162


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


The adjustable head restraints consist of : • a trimmed energy absorbing foam and structure (1), • two steel stems (2), • a guide sleeve adjust/release • and a guide sleeve unlock/remove


button (3),


button (4).


To adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button (3) and pushing down on the head restraint. Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants of extremely tall stature, adjust the head restraint to its full up position.


WARNING: The adjustable head restraint is a safety device. Whenever possible it should be installed and properly adjusted


when the seat is occupied.


To remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button (3) and the unlock/remove button (4), then pull up on the head restraint.


163


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


To reinstall the adjustable head restraint, do the following: 1. Insert the two stems (2) into the guide sleeve collars. 2. Push the head restraint down until it locks.


Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head. For occupants of extremely tall stature, adjust the head restraint to its full up position.


WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly.


164


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Front seat • Lift the track release bar to move


the seat forward or rearward. Make sure that the seat is relatched into place.


165


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints • Pull the release lever handle


located on the side of the seat up to move the seatback forward or backward.


Using the armrest (if equipped) • Push the release control to move • Pull out the drawer at the bottom


the armrest up or down.


of the center seat to access the cup holders (if equipped)


166


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


• To gain access to the storage compartment (if equipped) in your armrest, lift the latch to open the lid.


Using the manual lumbar support (if equipped) For more lumbar support, turn the lumbar support control toward the front of vehicle. For less lumbar support, turn the lumbar support control toward the rear of vehicle.


167


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the control for additional support. Press the rear side of the control to reduce support.


Adjusting the front power seat (if equipped)


WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving.


WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal


injuries in the event of a collision.


WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.


WARNING: To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in the seatback map pocket (if equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag off” indicator lamp for proper airbag status. Refer to Front passenger sensing system in the Airbag supplemental restraint system (SRS) section for additional details. Failure to follow these instructions may interfere with the front passenger seat sensing system.


168


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


The control is located on the outboard side of the seat cushion. Move the switch to raise or lower the front or rear portion of the seat cushion.


Move the switch to move the seat forward, backward, up or down.


Power recline (if equipped) Move the switch to recline the seatback forward or rearward.


169


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Memory seat/power mirrors/adjustable pedals/steering column (if equipped) This system allows automatic positioning of the driver seat, power mirrors, adjustable pedals, and steering column to two programmable positions. The memory seat control is located on the driver’s seat. • To program position 1, move the memory features to the desired positions using the associated controls. Press and hold button 1 for at least two seconds. A chime will sound confirming that a memory position has been set. • To program position 2, repeat the previous procedure using button 2. A memory seat position may be programmed at any time. To program the memory feature to a remote entry transmitter, refer to Remote entry system in the Locks and Security chapter. A programmed memory position can be recalled: • in any gearshift position if the ignition is not on. • only in P (Park) or N (Neutral) if the ignition is on. The memory positions are also recalled when you press your remote entry transmitter to a memory position) or, when you enter a valid personal entry code that is programmed to a memory position. The mirrors will move to the programmed position and the seat will move to the easy entry position. The seat will move to the final position when the key is in the ignition (if easy entry feature is enabled).


(unlock) control (if the transmitter is programmed


Easy-access/easy-out feature (if equipped) The easy entry feature can be turned off or on through the vehicle message center. Refer to Message center in the Instrument Cluster chapter. The easy entry feature automatically moves the driver’s seat 2 inches (5 cm) forward when: • the transmission is in P (Park) • the key is inserted into the ignition cylinder 170


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


(If the seat is located less than 2 inches [5 cm] from the front of the seat track, the seat will travel up to 1⁄4 inch (6 mm) to the front of the seat track). The easy out feature automatically moves the driver’s seat 2 inches (5 cm) backward when: • the transmission is in P (Park) • the key is removed from the ignition cylinder (If the seat is located less than 2 inches (5 cm) from the rear of the seat track, the seat will travel up to 1⁄4 inch (6 mm) to the rear of the seat track). If the memory setting is programmed through the remote transmitter, upon unlocking the door via remote entry system, the seat position will travel to the desired memory setting less 2 inches (5 cm). Once entering the vehicle and inserting the key in the ignition while in P (Park), the easy entry feature will move the seat an additional 2 inches (5 cm) to the desired memory location. See Locks and Security for activating the memory seat feature through the remote entry system.


Heated seats (if equipped)


WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord


injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.


Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the


seat. Allow the seat to dry thoroughly.


171


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


To operate the heated seats, do the following: Press the heated seat button/symbol to cycle through the various heat settings and off. Warmer settings are indicated by more indicator lights.


Heated and cooled seats (if equipped) The controls for the climate controlled seats are located on the climate control system. Heated seats


WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord


injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.


Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the


seat. Allow the seat to dry thoroughly.


The heated seats will only function when the engine is running. To operate the heated seats: Press the heated seat button/symbol to cycle through the various heat settings and off. Warmer settings are indicated by more indicator lights.


172


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Cooled seats The cooled seats will only function when the engine is running. To operate the cooled seats: Press the cooled seat button/symbol to cycle through the various cooling settings and off. Cooler settings are indicated by more indicator lights.


A/C


If the engine falls below 350 rpm while the cooled seats are on, the feature will turn itself off and will need to be reactivated. Climate controlled seats air filter replacement (if equipped) The heated and cooled seat system includes air filters that must be replaced periodically. Refer to Scheduled maintenance information. • There is a filter located under


each front seat.


• The filter can be accessed from the 2nd row foot-well area. Move the front seats all the way to the full front and full up positions to ease access.


To remove an air filter: 1. Turn the vehicle off. 2. Push up on the outside rigid edge of the filter until the tabs are released, then rotate the air filter toward the front of the vehicle.


173


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


3. Remove filter.


To install a filter: 1. First, position the filter in its housing making sure that the far forward end is all the way up in the housing. 2. Push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.


REAR SEATS


Second row head restraints Your vehicle is equipped with head restraints that are vertically adjustable.


WARNING: To minimize the risk of neck injury in the event of a crash, the driver and passenger occupants should not sit in and/or operate the vehicle, until the head restraint is placed in its proper position. The driver should never adjust the head restraint while the vehicle is in motion.


WARNING: The adjustable head restraint is a safety device. Whenever possible it should be installed and properly adjusted


when the seat is occupied.


174


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


The adjustable head restraints consist of : • a trimmed energy absorbing foam and structure (1), • two steel stems (2), • a guide sleeve adjust/release • and a guide sleeve unlock/remove


button (3),


button (4).


The second row head restraints look differently than the front head restraints, but function similarly. For details about how to raise, lower and remove/reinstall the second row head restraints, refer to Adjustable head restraints at the beginning of this chapter.


Folding up the rear seats (SuperCab only) The rear seat has a split 60/40 cushion. Each seat cushion can be flipped up into a vertical storage position. 1. Pull control to release seat cushion. 2. Rotate seat cushion up until it locks into vertical storage position.


Returning the seat to seating position


WARNING: Make sure that cargo or any objects are not trapped underneath the seat cushion before returning the seat cushion to its original position, and that the seat cushion locks into place. Failure to do so may prevent the seat from operating properly in the event of a crash, which could increase the risk of serious injury.


1. Pull control on the side of the seat to release seat cushion from storage position. 2. Push seat cushion down until it locks into horizontal position.


175


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Folding up the rear seats (SuperCrew vehicles only) The rear seat has a split 60/40 cushion. Each seat cushion can be flipped up into a vertical storage position. • Rotate the seat cushion up by lifting on the corner until it locks into vertical storage position.


Returning the seat to seating position


WARNING: Before returning the seat cushion to its original position, make sure that cargo or any objects are not trapped


underneath the seat cushion.


1. Pull control on the bottom of the seat cushion to release seat cushion from storage position. 2. Push seat cushion down until it rests into the horizontal position.


176


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Armrest and cupholders (if equipped) Pull the strap located on the center seatback to access the armrest and cupholders. The cupholders are located inside the rear seat armrest. To open the cupholders: • Push in gently on the center of the plastic panel on the front edge of the armrest. The cupholders will partially open.


• Pull the cupholder fully open before using. To close the cupholders: • Push the front edge back into the seat until the cupholders are fully • Make sure there is nothing in the cupholders before attempting to


seated.


close them.


Make sure that the cupholders are fully seated before stowing the armrest.


Rear heated seats (if equipped)


WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord


injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.


Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the


seat. Allow the seat to dry thoroughly.


The rear seat heat controls are located on the rear door armrest.


177


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


To operate the heated seats: • Push the indicated side of the control for maximum heat. • Push again to deactivate.


• Push the indicated side of the control for minimum heat. • Push again to deactivate.


The heated seat module resets at every ignition run cycle. While the ignition is in the on position, activating the high or low heated seat switch enables heating mode. When activated, they will turn off automatically when the engine is turned off. The indicator light will illuminate when the heated seats have been activated.


SAFETY RESTRAINTS


Personal Safety System™ The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant classifications and conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations. Your vehicle’s Personal Safety System consists of: • Driver and passenger dual-stage airbag supplemental restraints. • Front outboard safety belts with pretensioners, energy management • Driver’s seat position sensor. • Front crash severity sensor. • Front passenger sensing system 178


retractors, and safety belt usage sensors.


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


• Passenger Airbag Off indicator light. • Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and back-up tone. • The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, and indicator lights.


How does the Personal Safety System™ work? The Personal Safety System can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and occupant classification and conditions. A collection of crash and occupant sensors provides information to the Restraints Control Module (RCM). During a crash, the RCM may activate the safety belt pretensioners and/or either none, one, or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant classification and conditions. The fact that the pretensioners or airbags did not activate for both front seat occupants in a collision does not mean that something is wrong with the system. Rather, it means the Personal Safety System determined the accident conditions (crash severity, belt usage, etc.) were not appropriate to activate these safety devices. Front airbags are designed to activate only in frontal and near-frontal collisions, not rollovers, side-impacts, or rear-impacts unless the collision causes sufficient longitudinal deceleration. Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbag inflation energy. A lower, less forceful energy level is provided for more common, moderate-severity impacts. A higher energy level is used for the most severe impacts. Refer to Airbag Supplemental Restraints (SRS) section in this chapter. Front crash severity sensor The front crash severity sensor enhances the ability to detect the severity of an impact. Positioned up front, it provides valuable information early in the crash event on the severity of the impact. This allows your Personal Safety System to distinguish between different levels of crash severity and modify the deployment strategy of the dual-stage airbags and safety belt pretensioners. Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System to tailor the deployment level of the driver dual-stage airbag based on seat


179


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


position. The system is designed to help protect smaller drivers sitting close to the driver airbag by providing a lower airbag output level. Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, like infants in rear-facing child seats, this occurs because they are initially sitting very close to the airbag. For other occupants, this occurs when the occupant is not properly restrained by safety belts or child safety seats and they move forward during pre-crash braking. The most effective way to reduce the risk of unnecessary injuries is to make sure all occupants are properly restrained. Accident statistics suggest that children are much safer when properly restrained in the rear seating positions than in the front.


WARNING: Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air


bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.


WARNING: Always transport children 12 years old and under in the back seat and always properly use appropriate child


restraints.


WARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position.


The front passenger sensing system can automatically turn off the passenger front airbag when a rear facing child seat, a forward-facing child restraint, or a booster seat is detected. Even with this technology, parents are STRONGLY encouraged to always properly restrain children in the rear seat. The sensor also turns off the passenger front airbag and passenger seat-mounted side airbag when the passenger seat is empty. When the front passenger seat is occupied and the sensing system has turned off the passenger’s frontal airbag, the “pass airbag off” indicator will light and stay lit to remind you that the front passenger frontal airbag is off. See Front passenger sensing system in the Airbag supplemental restraint system (SRS) section of this chapter. 180


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Front safety belt usage sensors The front safety belt usage sensors detect whether or not the driver and front outboard passenger safety belts are fastened. This information allows your Personal Safety System to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage. Refer to Safety belt usage sensors later in this chapter. Front outboard safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’s body during frontal collisions, and in side collisions and rollovers. This helps increase the effectiveness of the safety belts. In frontal collisions, the safety belt pretensioners can be activated alone or, if the collision is of sufficient severity, together with the front airbags. Front outboard safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’s forward momentum. This helps reduce the risk of force-related injuries to the occupant’s chest by limiting the load on the occupant. Refer to Energy management retractors section in this chapter. Determining if the Personal Safety System is operational The Personal Safety System uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the Personal Safety System is not required. The Restraints Control Module (RCM) monitors its own internal circuits and the circuits for the airbag supplemental restraints, crash sensor(s), safety belt pretensioners, front safety belt buckle sensors, and the driver seat position sensor. In addition, the RCM also monitors the restraints warning light in the instrument cluster. A difficulty with the system is indicated by one or more of the following. • The warning light will either flash or stay lit. • The warning light will not illuminate immediately after ignition is • A series of five beeps will be heard. The tone pattern will repeat


turned on.


periodically until the problem and warning light are repaired.


181


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


If any of these things happen, even intermittently, have the Personal Safety System serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision. Safety restraints precautions


WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.


WARNING: To reduce the risk of injury, make sure children sit in a rear seating position where they can be properly restrained.


WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the


child from injury in a collision.


WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an


airbag supplemental restraint system (SRS) is provided.


WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.


WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety


belt.


WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one


tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.


182


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


WARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position.


WARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.


WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an


accident.


Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.


2. To unfasten, push the release button and remove the tongue from the buckle.


183


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Safety belt with cinch tongue (front center seat only) The cinch tongue will slide up and down the belt webbing when the belt is stowed or while putting safety belts on. When the lap/shoulder safety belt is buckled, the cinch tongue will allow the lap portion to be shortened, but pinches the webbing to keep the lap portion from getting longer. The cinch tongue is designed to slip during a crash, so always wear the shoulder belt properly and don’t allow any slack in either the lap or shoulder portions. Before you can reach and latch a combination lap and shoulder belt having a cinch tongue into the buckle, you may have to lengthen the lap belt portion of it. 1. To lengthen the lap belt, pull some webbing out of the shoulder belt retractor. 2. While holding the webbing below the tongue, grasp the tip (metal portion) of the tongue so that it is parallel to the webbing and slide the tongue upward.


3. Provide enough lap belt length so that the tongue can reach the buckle. How to fasten the cinch tongue 1. Pull the combination lap and shoulder belt from the retractor so that the shoulder belt portion of the safety belt crosses your shoulder and chest. 2. Be sure the belt is not twisted. If the belt is twisted, remove the twist. 3. Insert the belt tongue into the proper buckle for your seating position until you hear a snap and feel it latch. 4. Make sure the tongue is securely fastened to the buckle by pulling on the tongue.


WARNING: The lap belt should fit snugly and as low as possible around the hips, not across the waist.


WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an


accident.


184


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one


tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.


While you are fastened in the safety belt, the combination lap/shoulder belt with a cinch tongue adjusts to your movement. However, if you brake hard, turn hard, or if your vehicle receives an impact of 5 mph (8 km/h) or more, the safety belt will become locked and help reduce your forward movement. Restraint of pregnant women


WARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the


safety belt should fit snug and be positioned low across the hips. The shoulder portion of the safety belt should be positioned across the chest. Pregnant women should also follow this practice. See figure below.


Pregnant women should always wear their safety belt. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow. The shoulder belt should be positioned to cross the middle of the shoulder and the center of the chest.


Energy management retractors Your vehicle has a safety belt system equipped with energy management retractors at the driver and front outboard passenger seating positions. An energy management retractor is a device which pays out webbing in a controlled manner. This feature is designed to help further reduce the risk of force-related injuries to the occupant.


185


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Safety belt systems equipped with an energy management retractor must be replaced if they were in use during a frontal collision which resulted in deployment of the frontal airbags. Refer to the Safety belt maintenance section in this chapter.


Safety belt locking modes All safety restraints in the vehicle are combination lap and shoulder belts. The driver safety belt and the optional front center seat’s safety belt have the first locking mode only. All outboard passenger and rear safety belts have both types of locking modes described as follows: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 5 mph (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. In addition, the retractor is designed to lock if the webbing is pulled out too quickly. If this occurs, let the belt retract slightly and pull webbing out again in a slow and controlled manner. Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt or the optional front seat’s center safety belt. When to use the automatic locking mode This mode should be used any time a child safety seat is installed in a front outboard passenger seating position in a Regular Cab / SuperCab / SuperCrew or any rear seating position of a SuperCab or SuperCrew. The optional front seat’s center safety belt has a cinch mechanism. Refer to Safety belt with cinch tongue earlier in this chapter. Children 12 years old and under should be properly restrained in a rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter.


186


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


How to use the automatic locking mode 1. Buckle the combination lap and shoulder belt (front safety belt/buckle shown, rear similar). 2. Grasp the shoulder portion and pull downward until the entire belt is pulled out.


• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.


How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.


WARNING: After any vehicle collision, the safety belt system at all passenger seating positions must be checked by an authorized


dealer to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all safety belts should be checked for proper function.


WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking


retractor” feature or any other safety belt function is not operating properly when checked by an authorized dealer. Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.


Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and right front passenger seating positions. The safety belt pretensioner removes some slack from the safety belt system at the start of a crash. The safety belt pretensioner uses the same crash sensor system as the front airbags and Safety Canopy威 System. When the safety belt pretensioner deploys, the lap and shoulder belt are tightened.


187


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


When the Safety Canopy威 System and/or the front airbags are activated, the safety belt pretensioners for the driver and right front passenger seating positions will be activated when the respective seatbelt is properly buckled.


WARNING: The driver and the right front passenger safety belt system (including retractors, buckles and height adjusters) must


be replaced if the vehicle is involved in a collision that results in deployment of front airbags or Safety Canopy威 System and safety belt pretensioners.


WARNING: Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in


the event of a collision.


Refer to the Safety belt maintenance section in this chapter.


Safety belt usage sensors The driver and front outboard passenger safety belt buckles are equipped with sensors that detect if the safety belts are fastened. The sensors provide information to the Personal Safety System威 which can then adapt the airbag deployment or safety belt pretensioner activation based upon safety belt usage.


WARNING: The Personal Safety System威 provides the most benefit to belted occupants. The system monitors and tailors the


airbag deployment based upon safety belt usage. Failure to properly wear your safety belt will increase your risk of injury.


188


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Front safety belt height adjustment Your vehicle has safety belt height adjustments at the front outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To adjust the shoulder belt height, pull on the center button and slide the height adjuster down. Release the button and pull down on the height adjuster to make sure it is locked in place. To adjust the belt upward, slide the adjuster up and then pull down on the height adjuster to make sure it is locked in place


WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision.


Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.


Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the on position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the on position...


The safety belt warning light and indicator chime remain off.


The safety belt warning light and warning chime turn off.


189


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Belt-Minder姞 The Belt-Minder威 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster when the driver’s and front passenger’s safety belt is unbuckled. The Belt-Minder威 feature uses information from the front passenger sensing system to determine if a front seat passenger is present and therefore potentially in need of a warning. To avoid activating the Belt-Minder威 feature for objects placed in the front passenger seat, warnings will only be given to large front seat occupants as determined by the front passenger sensing system. Both the driver’s and passenger’s safety belt usages are monitored and either may activate the Belt-Minder威 feature. The warnings are the same for the driver and the front passenger. If the Belt-Minder威 warnings have expired (warnings for approximately five minutes) for one occupant (driver or front passenger), the other occupant can still activate the Belt-Minder威 feature. Note: If you are using MyKey威, the Belt-Minder威 warning will not expire. Refer to MyKey威 in the Locks and security chapter. When the Belt-Minder威 feature is activated, the safety belt warning light illuminates and the warning chime sounds for six seconds every 30 seconds, repeating for approximately five minutes or until the safety belts are buckled. The Belt-Minder威 feature uses two different warning chimes. During the first minute of activation, the warning chime will sound once every second. The remaining warning chimes will sound twice every second while the system is activated. If... The driver’s and front passenger’s safety belts are buckled... The driver’s or front passenger’s safety belt is not buckled when the vehicle has reached at least 6 mph and 1-2 minutes have elapsed since the ignition switch has been turned to ON...


The Belt-Minder威 feature is activated - the safety belt warning light illuminates and the warning chime sounds for six seconds every 30 seconds, repeating for approximately five minutes or until the safety belts are buckled.


Then... The Belt-Minder威 feature will not activate.


190


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


If... The driver’s or front passenger’s safety belt becomes unbuckled for approximately 1 minute while the vehicle is traveling at least 6 mph and 1-2 minutes have elapsed since the ignition switch has been turned to ON... The Belt-Minder威 feature is activated and the vehicle speed is less than 3 mph...


Then... The Belt-Minder威 feature is activated - the safety belt warning light illuminates and the warning chime sounds for six seconds every 30 seconds, repeating for approximately five minutes or until the safety belts are buckled.


The Belt-Minder威 feature is suspended - the safety belt warning light remains illuminated, but the warning chime does not sound. This time does not count towards the five-minute expiration time.


The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... “Crashes are rare events”


Consider... 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. 3 of 4 fatal crashes occur within 25
miles of home. We design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. Prime time for an accident. Belt-Minder威 reminds us to take a few seconds to buckle up.


191


“I’m not going far”


“Belts are uncomfortable”


“I was in a hurry”


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Reasons given... “Safety belts don’t work”


“Traffic is light”


“Belts wrinkle my clothes”


“The people I’m with don’t wear belts”


“I have an airbag”


“I’d rather be thrown clear”


Consider... Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4
times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see. Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”.


WARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder威 chime. To


do so may adversely affect the performance of the vehicle’s airbag system.


Deactivating/activating the Belt-Minder姞 feature The driver and front passenger Belt-Minder威 are deactivated/activated independently. When deactivating/activating one seating position, do not buckle the other position as this will terminate the process. 192


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Read Steps 1 - 4 thoroughly before proceeding with the deactivation/activation programming procedure. Note: If you are using MyKey威, the Belt-Minder威 cannot be disabled. Also, if the Belt-Minder威 has been previously disabled, it will be re-enabled after the use of MyKey威. Refer to MyKey威 in the Locks and security chapter. The driver and front passenger Belt-Minder威 features can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set • The gearshift is in P (Park) • The ignition switch is in the off position • The driver and front passenger safety belts are unbuckled


WARNING: While the design allows you to deactivate your Belt-Minder威, this system is designed to improve your chances of


being safely belted and surviving an accident. We recommend you leave the Belt-Minder威 system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do not deactivate/activate the Belt-Minder威 feature while driving the vehicle.


1. Turn the ignition switch to the on position. DO NOT START THE ENGINE. 2. Wait until the safety belt warning light turns off. (Approximately one minute) • Step 3 must be completed within 30 seconds after the safety belt


warning light turns off.


3. For the seating position being disabled, buckle then unbuckle the safety belt three times, ending in the unbuckled state. • After Step 3, the restraint system warning light (airbag light) will be


turned on for three seconds.


4. Within approximately seven seconds of the light turning off, buckle then unbuckle the safety belt. • This will disable the Belt-Minder威 feature for that seating position if it


is currently enabled. As confirmation, the restraint system warning light will flash four times per second for three seconds.


193


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints • This will enable the Belt-Minder威 feature for that seating position if it


is currently disabled. As confirmation, the restraint system warning light will flash four times per second for three seconds, followed by three seconds with the light off, then followed by the restraint system warning light flashing four times per second for three seconds again.


Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch (20 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended.


WARNING: Do not use extensions to change the fit of the shoulder belt across the torso.


AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)


The airbag supplemental restraint system is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries. The term “supplemental restraint” means the airbags are intended as a supplement to the safety belts. Airbags alone cannot protect as well as airbags plus safety belts in impacts for which the airbags are designed to deploy, and airbags do not offer any protection in crashes for which they do not deploy. 194


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


inflators and airbags).


system and Safety Canopy威 system later in this chapter.


The airbag supplemental restraint system consists of: • driver and passenger dual stage airbag modules (which include the • side airbags and Safety Canopy威. Refer to Seat-mounted side airbag • one or more impact and safing sensors. • the same indicator light, RCM (restraints control module) and • Front passenger sensing system • Passenger airbag off indicator light. The airbag supplemental restraints are an integral part of the Personal Safety System. They are designed to be deployed in cases where the Personal Safety System has determined the occupant conditions and crash severity are appropriate to activate these devices. Refer to the Personal Safety System™ section in this chapter.


diagnostic unit used for the Personal safety system.


Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag.


WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air


bag supplemental restraint system (SRS) is provided.


WARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position.


195


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


WARNING: The National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches


(25 cm) between an occupant’s chest and the driver airbag module.


WARNING: Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other


injuries.


pedals comfortably.


To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the • Recline the seat slightly one or two degrees from the upright position. WARNING: Do not put anything on or over the airbag module. Placing objects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury.


WARNING: Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses. Contact your


authorized dealer as soon as possible.


WARNING: The front passenger airbag is not designed to offer protection to an occupant in the center front seating position.


WARNING: Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure


and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of the vehicle.


WARNING: Additional equipment may affect the performance of the airbag sensors increasing the risk of injury.


196


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Children and airbags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seat than in the front seat. Failure to follow these instructions may increase the risk of injury in a collision.


WARNING: Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.


If two adults and a child occupy a Regular Cab, properly restrain the child in the center front unless doing so would interfere with driving the vehicle. This arrangement provides lap and shoulder belt protection for all occupants, and airbag protection for the adults. All occupants of the vehicle should always properly wear their safety belts. Ensure the child is properly restrained in an appropriate child seat or with the use of a booster. A child or infant properly restrained in the center front seat should not incur risk of serious injury from the airbags.


197


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Airbags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts. The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic. While the system is designed to help reduce serious injuries, it may also cause minor abrasions, swelling or temporary hearing loss. Because airbags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag cover as possible while maintaining vehicle control.


WARNING: Several airbag system components get hot after inflation. Do not touch them after inflation.


198


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


WARNING: If the airbag has deployed, the airbag will not function again and must be replaced immediately. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.


Front passenger sensing system The front passenger sensing system is designed to meet the regulatory requirements of Federal Motor Vehicle Safety Standard (FMVSS) 208
and is designed to disable (will not inflate) the front passenger’s frontal airbag under certain conditions. The front passenger sensing system works with sensors that are part of the front passenger’s seat and safety belt. The sensors are designed to detect the presence of a properly seated occupant and determine if the front passenger’s frontal airbag should be enabled (may inflate) or disabled (will not inflate). The front passenger sensing system will disable (will not inflate) the front passenger’s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in • the system determines that an infant is present in a rear-facing infant • the system determines that a small child is present in a forward-facing


seat that is installed according to the manufacturer’s instructions,


the front seat,


child restraint that is installed according to the manufacturer’s instructions,


• the system determines that a small child is present in a booster seat, • a front passenger takes his/her weight off of the seat for a period of • a child or a small person occupies the front passenger seat. Note: When the passenger airbag off light is illuminated, the passenger (seat mounted) side airbag may be disabled to avoid the risk of airbag deployment injuries.


time,


199


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


The front passenger sensing system uses a ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. The indicator lamp is located in the center stack of the instrument panel just above the radio. Note: The indicator lamp will illuminate for a short period of time when the ignition is turned to the on position to confirm it is functional. When the front passenger seat is not occupied (empty seat) or in the event that the front passenger frontal airbag is enabled (may inflate), the indicator lamp will be unlit. The front passenger sensing system is designed to disable (will not inflate) the front passenger’s frontal airbag when a rear facing infant seat, a forward-facing child restraint, or a booster seat is detected. • When the front passenger sensing system disables (will not inflate) the front passenger frontal airbag, the indicator lamp will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. • If the child restraint has been installed and the indicator lamp is not


lit, then turn the vehicle off, remove the child restraint from the vehicle and reinstall the restraint following the child restraint manufacturer’s instructions.


The front passenger sensing system is designed to enable (may inflate) the front passenger’s frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat. • When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator will be unlit and stay unlit. If a person of adult size is sitting in the front passenger’s seat, but the ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it is possible that the person isn’t sitting properly in the seat. If this happens: • Turn the vehicle off and ask the person to place the seatback in the • Have the person sit upright in the seat, centered on the seat cushion, • Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’s frontal airbag.


with the person’s legs comfortably extended.


full upright position.


200


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints • If the indicator lamp remains lit even after this, the person should be


advised to ride in the rear seat.


Occupant


Empty seat Small child in child safety seat or booster Small child with safety belt buckled or unbuckled Adult


Pass Airbag Off Indicator Lamp Unlit Lit


Lit


Unlit


Passenger Airbag


Disabled Disabled


Disabled


Enabled


WARNING: Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a rear seating


position.


After all occupants have adjusted their seats and put on safety belts, it’s very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.


WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion


and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.


The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙pass airbag off⬙ lamp may or may not be illuminated according to the table below.


201


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Pass Airbag Off Indicator Lamp Unlit


Objects


Passenger Airbag


Lit


Disabled


Disabled


Small (i.e. three-ring binder, small purse, bottled water) Medium (i.e. heavy briefcase, fully packed luggage) Empty seat, or small to medium object with safety belt buckled In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. DO NOT attempt to repair or service the system; take your vehicle immediately to an authorized dealer.


Disabled


Lit


WARNING: The front passenger airbag is not designed to offer protection to an occupant in the center seating position.


WARNING: An out of position front center occupant could affect the decision of the front passenger sensing system.


If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance chapter of this Owner’s Guide.


WARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing


system.


Determining if the system is operational The SRS uses readiness lights in the instrument cluster or a tone to indicate the condition of the system. Refer to Airbag readiness in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. 202


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


flash or stay lit.


A difficulty with the system is indicated by one or more of the following: • The readiness lights will either • The readiness lights will not illuminate immediately after ignition is turned on.


• A series of five beeps will be heard. The tone pattern will repeat


periodically until the problem and/or light are repaired.


If any of these things happen, even intermittently, have the SRS serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision.


Seat-mounted side airbag system


WARNING: Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front


seats or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.


WARNING: Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side


airbags and increase the risk of injury in an accident.


WARNING: Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the seatback.


WARNING: Do not attempt to service, repair, or modify the airbag SRS, its fuses or the seat cover on a seat containing an


airbag. See an authorized dealer.


WARNING: All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.


203


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags. The side airbag system consists of the following: • An inflatable bag (airbag) with a gas generator concealed behind the • A special seat cover designed to allow airbag deployment. • The same warning light, electronic control and diagnostic unit as used • Crash sensors located on the front doors. • One crash sensor located on each side of the b-pillar, (SuperCab only). • One crash sensor located on each side of the c-pillar, (SuperCrew


outboard bolster of the driver and front passenger seatbacks.


for the front airbags.


only).


Side airbags, in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision. The side airbags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the airbag on the side affected by the collision will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions. The airbag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Side airbags are designed to inflate in side-impact collisions, not roll-over, rear-impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration. 204


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


WARNING: Several airbag system components get hot after inflation. Do not touch them after inflation.


WARNING: If the side airbag has deployed, the


airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.


Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to Warning lights and chimes in the Instrument Cluster chapter. Routine maintenance of the side airbag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will either • The readiness light will not illuminate immediately after ignition is • A series of five beeps will be heard. The tone pattern will repeat


flash or stay lit.


turned on.


periodically until the problem and/or light are repaired.


If any of these things happen, even intermittently, have the SRS serviced at your authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision.


205


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


Safety Canopy姞 System


WARNING: Do not place objects or mount equipment


on or near the headliner at the siderail that may come into contact with a deploying Safety Canopy威. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.


WARNING: Do not lean your head on the door. The Safety Canopy威 could injure you as it deploys from the headliner.


WARNING: Do not attempt to service, repair, or modify the Safety Canopy威 System, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy威. Contact your authorized dealer as soon as possible.


WARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS


and Safety Canopy威 System is provided.


WARNING: To reduce risk of injury, do not obstruct or place objects in the deployment path of the inflatable Safety Canopy威.


206


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


How does the Safety Canopy姞 System work? The design and development of the Safety Canopy system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety Canopy威). The Safety Canopy system consists of the following: • An inflatable curtain with a gas generator concealed behind the headliner and in the corner or C pillar behind the doors. • A headliner designed to flex open • The same warning light, electronic control and diagnostic unit as used • Two crash sensors located on the C-pillar (one on each side) • Crash sensors located on the front doors. • Rollover sensor in the restraints control module (RCM). The Safety Canopy system, in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision or rollover event. Children 12 years old and under should always be properly restrained in the second row seats. The Safety Canopy will not interfere with children restrained using a properly installed child or boost er seat because it is designed to inflate downward from the headliner above the doors along the side window opening. The Safety Canopy system is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the RCM to initiate Safety Canopy inflation or when a certain likelihood of a rollover event is detected by the rollover sensor.


above the side doors to allow Safety Canopy deployment.


(SuperCab and SuperCrew only).


for the front airbags.


207


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


The Safety Canopy is mounted to roof side-rail sheet metal, behind the headliner, above each row of seats. The Safety Canopy is designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events. The fact that the Safety Canopy did not activate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. The Safety Canopy is designed to inflate in certain side impact collisions or rollover events, not in rear impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration or rollover likelihood.


WARNING: Several Safety Canopy system components


get hot after inflation. Do not touch them after inflation.


WARNING: If the Safety Canopy system has deployed, the Safety Canopy will not function again unless replaced. The


Safety Canopy system (including the A, B, C, and D pillar trim and headliner) must be inspected and serviced by an authorized dealer. If the Safety Canopy is not replaced, it will not function again, which will increase the risk of injury in a future collision.


Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to Warning lights and chimes in the Instrument Cluster chapter. Routine maintenance of the side airbag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will either • The readiness light will not illuminate immediately after ignition is • A series of five beeps will be heard. The tone pattern will repeat


flash or stay lit.


turned on.


periodically until the problem and/or light are repaired.


208


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


If any of these things happen, even intermittently, have the SRS serviced at your authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision.


SOS Post-Crash Alert System™ The system automatically flashes the turn signal lamps and sounds the horn three times at four second intervals in the event of a serious impact that deploys an airbag (front, side, side curtain [if equipped] or Safety Canopy威 [if equipped]) or the safety belt pretensioners. The system can be turned off when any one of the following actions are taken by the driver or any other person: • pressing the hazard control button, • or pressing the panic button on the remote entry transmitter. The feature will continue to operate until the vehicle runs out of power.


Disposal of airbags and airbag equipped vehicles (including pretensioners) Contact your authorized dealer as soon as possible. Airbags MUST BE disposed of by qualified personnel.


SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags.


Important child restraint precautions


WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight.


Child safety restraints must be purchased separately from the vehicle. Failure to follow these instructions and guidelines may result in an increased risk of serious injury or death to your child.


209


2011 F-150 (f12) Owners Guide, 3rd Printing USA (fus)


Seating and Safety Restraints


WARNING: All children are shaped differently. The Recommendations for Safety Restraints are based on probable


child height, age and weight thresholds from NHTSA and other safety organizations or are the minimum requirements of law. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician (CPST) and consult your pediatrician to make sure your child seat is appropriate for your child, and is compatible with and properly installed in the vehicle. To locate a child seat fitting station and CPST contact the NHTSA toll free at 1-888-327-4236 or on the internet at http://www.nhtsa.dot.gov. In Canada, check with your local St. John Ambulance office for referral to a CPST or for further information, contact your provincial ministry of transportation, your

Loading...
x