2015 Ford Escape Owners Manual

I (accessory) - Allows the electrical accessories, such as the radio, to operate while the engine is not running. Note: Do not leave the ignition key in this position for too long. This could cause your vehicle battery to lose charge. II (on) - All electrical circuits are operational and the warning lamps and indicators illuminate. III (start) - cranks the engine. KEYLESS STARTING (If Equipped) Note: The keyless starting system may not function if the key is close to metal objects or electronic devices such as cellular phones Note: A valid key must be located inside your vehicle to switch the ignition on and start the engine.

Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up

the engine compartment and exhaust system, creating the risk of fire.

Do not start the engine in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.

If you smell exhaust fumes inside your vehicle, have your vehicle checked by an authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes.

If you disconnect the battery, your vehicle may exhibit some unusual driving characteristics for approximately 5 miles (8 kilometers) after you reconnect it. This is because the engine management system must realign itself with the engine. You can disregard any unusual driving characteristics during this period. The powertrain control system meets all Canadian interference-causing equipment standard requirements regulating the impulse electrical field or radio noise. When you start the engine, avoid pressing the accelerator pedal before and during operation. Only use the accelerator pedal when you have difficulty starting the engine.

128

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E72128Starting and Stopping the Engine

Ignition Modes

Before starting the engine check the following: • Make sure all occupants have fastened

their safety belts.

• Make sure the headlamps and electrical accessories are off.

• Make sure the parking brake is on. • Move the transmission selector lever

to position P. Turn the ignition key to position II. If your vehicle is equipped with a keyless ignition, see the following instructions.

•

Vehicles with an Ignition Key Note: Do not touch the accelerator pedal. 1. Fully press the brake pedal. 2. Turn the key to position III to start the

engine. Release the key when the engine starts.

Note: The engine may continue cranking for up to 15 seconds or until it starts. Note: If you cannot start the engine on the first try, wait for a short period and try again. Vehicles with Keyless Start Note: Do not touch the accelerator pedal. 1. Fully press the brake pedal. 2. Press the button. The system does not function if: • • If you are unable to start the engine, do the following:

The key frequencies are jammed. The key battery has no charge.

The keyless starting system has three modes: Off: Turns the ignition off. • Without applying the brake pedal, press and release the button once when the ignition is in the on mode, or when the engine is running but the vehicle is not moving.

On: All electrical circuits are operational and the warning lamps and indicators illuminate. • Without applying the brake pedal, press and release the button once.

Start: Starts the engine. • Press the brake pedal, and then press

and hold the button until the engine starts.

STARTING A GASOLINE ENGINE When you start the engine, the idle speed increases, this helps to warm up the engine. If the engine idle speed does not slow down automatically, have your vehicle checked by an authorized dealer.

129

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E142555Starting and Stopping the Engine

Once the engine has started, it remains running until you press the button, even if the system does not detect a valid key. If you open and close a door while the engine is running, the system searches for a valid key. You cannot restart the engine if the system does not detect a valid key within 20 seconds. Failure to Start If you cannot start the engine after three attempts, wait 10 seconds and follow this procedure: 1. Fully press the brake pedal. 2. Fully press the accelerator pedal and

hold it there.

3. Start the engine. Automatic Engine Shutdown If your vehicle is equipped with a keyless ignition, it has a feature that automatically shuts down the engine if it has been idling for an extended period. The ignition also turns off in order to save battery power. Before the engine shuts down, a message appears in the information display showing a timer counting down from 30 seconds. If you do not intervene within 30 seconds, the engine shuts down. Another message appears in the information display to inform you that the engine has shut down in order to save fuel. Start your vehicle as you normally do. Automatic Engine Shutdown Override Note: You cannot permanently switch off the automatic engine shutdown feature. When you switch it off temporarily, it turns on at the next ignition cycle.

3-button remote

5-button remote

1. Hold the key next to the symbol on the

steering column.

2. With the key in this position, you can

use the start button to switch the ignition on and start your vehicle.

Fast Restart The fast restart feature allows you to restart the engine within 20 seconds of switching it off, even if a valid key is not present. Within 20 seconds of switching the engine off, press the brake pedal and press the button. After 20 seconds have expired, you can no longer restart the engine without the key present inside your vehicle.

130

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E145988E142874Starting and Stopping the Engine

Stopping the Engine When Your Vehicle is Moving

WARNING

Switching off the engine when the vehicle is still moving will result in a loss of brake and steering assistance. The steering will not lock, but higher effort will be required. When the ignition is switched off, some electrical circuits, including air bags, warning lamps and indicators may also be off. If the ignition was turned off accidentally, you can shift into neutral (N) and re-start the engine.

Vehicles with an Ignition Key 1. Move the transmission selector lever to position N and use the brakes to bring your vehicle to a safe stop.

2. When your vehicle has stopped, move the transmission selector lever to position P and turn the key to position 0.

3. Apply the parking brake. Vehicles with Keyless Start 1. Move the transmission selector lever to position N and use the brakes to bring your vehicle to a safe stop.

2. When your vehicle has stopped, move

the transmission selector lever to position P.

3. Press and hold the button for one

second, or press it three times within two seconds.

4. Apply the parking brake.

You can stop the engine shutdown, or reset the timer, at any point before the 30-second countdown has expired by doing any of the following: •

You can reset the timer by interacting with your vehicle (such as pressing the brake pedal or accelerator pedal). You can temporarily switch off the shutdown feature any time the ignition is on (for the current ignition cycle only). Use the information display to do so. See Information Displays (page 93).

•

• During the countdown before engine shutdown, you are prompted to press OK or RESET (depending on your type of information display) to temporarily switch the feature off (for the current ignition cycle only).

Stopping the Engine When Your Vehicle is Stationary Vehicles with an Ignition Key 1. Move the transmission selector lever

to position P.

2. Turn the key to position 0. 3. Apply the parking brake. Vehicles with Keyless Start 1. Move the transmission selector lever

to position P.

2. Press the button once. 3. Apply the parking brake. Note: This switches off the ignition, all electrical circuits, warning lamps and indicators.

131

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Starting and Stopping the Engine

The heater acts as a starting aid by warming the engine coolant. This allows the climate control system to respond quickly. The equipment includes a heater element (installed in the engine block) and a wire harness. You can connect the system to a grounded 120-volt AC electrical source. We recommend that you do the following for a safe and correct operation: • Use a 16-gauge outdoor extension cord

that is product certified by Underwriter’s Laboratory (UL) or Canadian Standards Association (CSA). This extension cord must be suitable for use outdoors, in cold temperatures, and be clearly marked Suitable for Use with Outdoor Appliances. Do not use an indoor extension cord outdoors. This could result in an electric shock or become a fire hazard.

• Use as short an extension cord as

possible.

• Do not use multiple extension cords. • Make sure that when in operation, the

extension cord plug and heater cord plug connections are free and clear of water. This could cause an electric shock or fire.

• Make sure your vehicle is parked in a

clean area, clear of combustibles.

• Make sure the heater, heater cord and extension cord are firmly connected.

• Check for heat anywhere in the

electrical hookup once the system has been operating for approximately 30
minutes.

Guarding Against Exhaust Fumes

WARNING

If you smell exhaust fumes inside your vehicle, have your vehicle checked by your authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. Important Ventilating Information If you stop your vehicle and the leave the engine idling for long periods of time, we recommend that you do one of the following: • Open the windows at least 1 inch (2.5

centimeters) Set your climate control to outside air.

• ENGINE BLOCK HEATER (If Equipped)

WARNINGS

Failure to follow engine block heater instructions could result in property damage or serious personal injury. Do not use your heater with ungrounded electrical systems or two-pronged adapters. There is a risk

of electrical shock.

Do not fully close the hood, or allow it to drop under its own weight when using the engine block heater. This could damage the power cable and may cause an electrical short resulting in fire, injury and property damage.

Note: The heater is most effective when outdoor temperatures are below 0°F (-18°C).

132

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Starting and Stopping the Engine

• Make sure the system is unplugged and

properly stowed before starting and driving your vehicle. Make sure the protective cover seals the prongs of the block heater cord plug when not in use.

• Make sure the heater system is

checked for proper operation before winter.

Using the Engine Block Heater Make sure the receptacle terminals are clean and dry prior to use. Clean them with a dry cloth if necessary. The heater uses 0.4 to 1.0 kilowatt-hours of energy per hour of use. The system does not have a thermostat. It achieves maximum temperature after approximately three hours of operation. Using the heater longer than three hours does not improve system performance and unnecessarily uses electricity.

133

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Fuel and Refueling

SAFETY PRECAUTIONS

WARNINGS

Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray

and fire.

The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel capless fuel system), do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.

Automotive fuels can cause serious injury or death if misused or mishandled. Flow of fuel through a fuel pump nozzle can produce static electricity. This can cause a fire if you are filling

an ungrounded fuel container.

Fuel ethanol and gasoline may contain benzene, which is a cancer-causing agent. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes.

Observe the following guidelines when handling automotive fuel: •

Extinguish all smoking materials and any open flames before refueling your vehicle.

• Always turn off the vehicle before

refueling.

Escape (TM2) Canada/United States of America, enUSA, Second Printing

• Automotive fuels can be harmful or

fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours.

• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.

• Avoid getting fuel liquid in your eyes. If

fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin, clothing or both, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.

•

•

134

Fuel and Refueling

FUEL QUALITY Choosing the Right Fuel Use only UNLEADED gasoline or UNLEADED gasoline blended with a maximum of 15% ethanol in your gasoline vehicle. If your vehicle is a Flex Fuel Vehicle (FFV), it will have a yellow bezel placed over the fuel fill inlet. Do not use: •

Fuels containing more than 15% ethanol or E-85 fuel. Fuels containing methanol. Fuels containing metallic based additives, including manganese-based compounds. Fuels containing the octane booster additive, methylcyclopentadienyl manganese tricarbonyl (MMT). Leaded-fuel (The use of leaded fuel is prohibited by law).

• •

•

•

Note: Use of any fuel other than recommended fuel can cause powertrain damage, impair the emission control system or cause loss of vehicle performance. Any damage to vehicle that is caused by use of fuel not recommended will not be covered under warranty. Octane Recommendations

Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, contact an authorized dealer to prevent any engine damage. 2.5L Engines We recommend regular unleaded gasoline with a pump octane rating of 87. Some fuel stations offer fuels posted as regular with an octane rating below 87, particularly in high altitude areas. We do not recommend fuels with an octane rating below 87. 1.6L and 2.0L EcoBoost Engines We recommend regular unleaded gasoline with a pump octane rating of 87. Some fuel stations offer fuels posted as regular with an octane rating below 87, particularly in high altitude areas. We do not recommend fuels with an octane rating below 87. RUNNING OUT OF FUEL Avoid running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel:

135

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E161513Fuel and Refueling

•

You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. With keyless ignition, just start the engine. Crank time will be longer than usual.

• Normally, adding 1 gallon (3.8 liters) of fuel is enough to restart the engine. If the vehicle is out of fuel and on a steep grade, more than 1 gallon (3.8 liters) may be required. The service engine soon indicator may come on. For more information on the service engine soon indicator, See Warning Lamps and Indicators (page 89).

•

Refilling With a Portable Fuel Container

WARNINGS

Do not insert the nozzle of portable fuel containers or aftermarket funnels into the capless fuel system. This could damage the fuel system and its seal, and may cause fuel to run onto the ground instead of filling the tank, which could result in serious personal injury.

Do not try to pry open or push open the capless fuel system with foreign objects. This could damage the fuel system and its seal and cause injury to you or others.

Note: Do not use aftermarket funnels; they will not work with the capless fuel system and can damage it. The included funnel has been specially designed to work safely with your vehicle.

When filling the vehicle’s fuel tank from a portable fuel container, use the funnel included with the vehicle. The funnel is located in the rear of the vehicle, inside the load compartment, underneath the load floor carpet. 1. Locate the portable funnel that comes

with your vehicle.

2. Slowly insert the funnel into the

capless fuel system.

3. Fill the vehicle with fuel from the

portable fuel container.

4. When done, clean the funnel or

properly dispose of it. Extra funnels can be purchased from your authorized dealer if you choose to dispose of the funnel.

136

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E157279E157280Fuel and Refueling

•

Keep the fuel pump nozzle in contact with the fuel container while filling. • Do not use a device that would hold

the fuel pump handle in the fill position. Easy Fuel™ Capless Fuel System

WARNING

The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.

When fueling your vehicle: 1. When your vehicle has stopped, shift into park (P) and switch the ignition off.

2. Open the fuel filler door.

3. Slowly insert the fuel filler nozzle fully

into the fuel system, and leave the nozzle fully inserted until you are done pumping. Hold handle higher during insertion for easier access.

REFUELING

WARNINGS

Fuel vapor burns violently and a fuel fire can cause severe injuries. Read and follow all the instructions on the pump island. When refueling always shut the engine off and never allow sparks or open flames near the fuel tank filler

valve. Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes.

Stay outside your vehicle and do not leave the fuel pump unattended when refueling your vehicle. This is

against the law in some places.

Keep children away from the fuel pump; never let children pump fuel. Wait at least 10 seconds before removing the fuel pump nozzle to allow any residual fuel to drain into

the fuel tank.

Stop refueling after the fuel pump nozzle automatically shuts off for the second time. Failure to follow this

will fill the expansion space in the fuel tank and could lead to fuel overflowing.

Do not remove the fuel pump nozzle from its fully inserted position when refueling.

Use the following guidelines to avoid electrostatic charge build-up, which can produce a spark, when filling an ungrounded fuel container: • Place approved fuel container on the

ground.

• Do not fill a fuel container while it is in the vehicle (including the cargo area).

137

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E156032Fuel and Refueling

If this action corrects the problem, the message may not reset immediately. It may take several driving cycles for the message to turn off. A driving cycle consists of an engine start-up (after 4 or more hours with the engine off) followed by city or highway driving. Continuing to drive with the message on may cause the service engine soon lamp to turn on as well. FUEL CONSUMPTION Note: The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. Empty reserve is the amount of fuel remaining in the tank after the fuel gauge indicates empty. Do not rely on this fuel for driving. The usable capacity of the fuel tank is the amount of fuel that can be put into the tank after the gauge indicates empty. The advertised capacity is the total fuel tank size – it is the combined usable capacity plus the empty reserve. Filling the Tank For consistent results when filling the fuel tank: •

Turn the ignition off before fueling; an inaccurate reading results if the engine is left running.

• Use the same fill rate

(low-medium-high) each time the tank is filled.

• Allow no more than two automatic

click-offs when filling.

Results are most accurate when the filling method is consistent.

4. Wait at least 10 seconds before

removing the fuel pump nozzle to allow any residual fuel to drain into the fuel tank.

Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank. The fill pipe is equipped with a drain hole. Excess fuel due to overfill may drain through the drain hole and drip onto the ground. If the fuel fill inlet was not properly closed, a service engine warning lamp may appear on the instrument cluster. At the next opportunity, do the following: 1. Stop your vehicle as soon as safely

possible and shift the transmission into park (P).

2. Open the fuel filler door and remove

any visible debris from the fuel fill opening. Insert either the fuel fill nozzle or the fuel fill funnel provided with the vehicle several times to allow the inlet to close properly. This will dislodge any debris preventing the inlet from sealing.

3.

138

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E154765Fuel and Refueling

WARNINGS

Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. If

you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.

Your vehicle is equipped with various emission control components and a catalytic converter that will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. • Avoid running out of fuel. • Do not turn off the ignition while your

vehicle is moving, especially at high speeds.

• Have the items listed in scheduled

maintenance information performed according to the specified schedule. The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system. If you use parts other than Ford, Motorcraft or Ford-authorized parts for maintenance replacements, or for service of components affecting emission control, such non-Ford parts should be the equivalent to genuine Ford Motor Company parts in performance and durability. Illumination of the service engine soon indicator, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power could indicate that the emission control system is not working properly.

Calculating Fuel Economy Do not measure fuel economy during the first 1000 miles (1600 kilometers) of driving (this is your engine’s break-in period); a more accurate measurement is obtained after 2000 miles - 3000 miles (3200 kilometers - 4800 kilometers). Also, fuel expense, frequency of fill ups or fuel gauge readings are not accurate ways to measure fuel economy. 1. Fill the fuel tank completely and record

the initial odometer reading.

2. Each time you fill the tank, record the

amount of fuel added.

3. After at least three to five tank fill ups, fill the fuel tank and record the current odometer reading.

4. Subtract your initial odometer reading

from the current odometer reading. 5. Calculate fuel economy by dividing miles traveled by gallons used (For Metric: Multiply liters used by 100, then divide by kilometers traveled).

Keep a record for at least one month and record the type of driving (city or highway). This provides an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter show how temperature impacts fuel economy. In general, lower temperatures mean lower fuel economy. EMISSION CONTROL SYSTEM

WARNINGS

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the

engine compartment and exhaust system, which can start a fire.

139

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Fuel and Refueling

An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately. Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal also lists engine displacement Please consult your warranty information for complete details. On-Board Diagnostics (OBD-II) Your vehicle has a computer known as the on-board diagnostics system (OBD-II) that monitors the engine’s emission control system. The system protects the environment by making sure that your vehicle continues to meet government emission standards. The OBD-II system also assists a service technician in properly servicing your vehicle.

When the service engine soon indicator illuminates, the OBD-II system has detected a

malfunction. Temporary malfunctions may cause the service engine soon indicator to illuminate. Examples of temporary malfunctions are: •

the vehicle has run out of fuel—the engine may misfire or run poorly poor fuel quality or water in the fuel—the engine may misfire or run poorly

•

•

•

the fuel fill inlet may not have closed properly. See Refueling (page 137). driving through deep water—the electrical system may be wet. You can correct these temporary malfunctions by filling the fuel tank with good quality fuel, properly closing the fuel fill inlet or letting the electrical system dry out. After three driving cycles without these or any other temporary malfunctions present, the service engine soon indicator should stay off the next time you start the engine. A driving cycle consists of a cold engine startup followed by mixed city/highway driving. No additional vehicle service is required. If the service engine soon indicator remains on, have your vehicle serviced at the first available opportunity. Although some malfunctions detected by the OBD-II may not have symptoms that are apparent, continued driving with the service engine soon indicator on can result in increased emissions, lower fuel economy, reduced engine and transmission smoothness, and lead to more costly repairs. Readiness for Inspection/Maintenance (I/M) Testing Some state/provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration.

If the service engine soon indicator is on or the bulb does not work, you may need to have

the vehicle serviced. See On-Board Diagnostics (OBD-II).

140

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Fuel and Refueling

Your vehicle may not pass the I/M test if the service engine soon indicator is on or not working properly (bulb is burned out), or if the OBD-II system has determined that some of the emission control systems have not been properly checked. In this case, your vehicle is not ready for I/M testing. If the vehicle’s engine or transmission has just been serviced, or the battery has recently run down or been replaced, the OBD-II system may indicate that the vehicle is not ready for I/M testing. To determine if the vehicle is ready for I/M testing, turn the ignition key to the on position for 15 seconds without cranking the engine. If the service engine soon indicator blinks eight times, it means that the vehicle is not ready for I/M testing; if the service engine soon indicator stays on solid, it means that the vehicle is ready for I/M testing. The OBD-II system monitors the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, you may need to perform the following driving cycle consisting of mixed city and highway driving: Drive on an expressway or highway for a steady 15 minutes, followed by 20 minutes of stop-and-go driving with at least four 30-second idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. If the vehicle is still not ready for I/M testing, you will have to repeat the above driving cycle.

141

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Transmission

Reverse (R) With the gearshift lever in reverse (R), your vehicle will move backward. Always come to a complete stop before shifting into and out of reverse (R). Neutral (N) With the gearshift lever in neutral (N), your vehicle can be started and is free to roll. Hold the brake pedal down while in this position. Drive (D) Drive (D) is the normal driving position for the best fuel economy. The overdrive function allows automatic upshifts and downshifts through gears one through six. Sport (S) Moving the gearshift lever to sport (S): • Provides additional grade (engine)

braking and extends lower gear operation to enhance performance for uphill climbs, hilly terrain or mountainous areas. This will increase engine RPM during engine braking.

• Provides additional lower gear

operation through the automatic transmission shift strategy.

• Gears are selected more quickly and

at higher engine speeds.

SelectShift Automatic™ Transmission Your SelectShift automatic transmission gives you the ability to manually change gears. To use SelectShift, move the gearshift lever into sport (S). Use the +/- buttons on the side of your gearshift lever to manually change gears. • Press the (+) button to upshift. • Press the (-) button to downshift.

AUTOMATIC TRANSMISSION

WARNINGS

Always set the parking brake fully and make sure the gearshift is latched in park (P). Turn the ignition

to the off position and remove the key whenever you leave your vehicle.

Do not apply the brake pedal and accelerator pedal simultaneously. Applying both pedals simultaneously

for more than three seconds will limit engine rpm, which may result in difficulty maintaining speed in traffic and could lead to serious injury. Understanding the Positions of Your Automatic Transmission Putting your vehicle in gear: 1. Fully press down the brake pedal. 2. Press and hold the button on the front

of the gearshift lever.

3. Move the gearshift lever into the

desired gear.

4. Release the button and your

transmission will remain in the selected gear.

Park (P) This position locks the transmission and prevents the wheels from turning.

142

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E142629Transmission

WARNINGS

When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll

freely. To avoid unwanted vehicle movement, always fully set the parking brake prior to doing this procedure. Use wheel chocks if appropriate.

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be

working properly. See your authorized dealer.

Use the brake shift interlock lever to move the gearshift lever from the park position in the event of an electrical malfunction or if your vehicle has a dead battery. Apply the parking brake and turn the ignition off before performing this procedure. 1.

Insert a screwdriver (or similar tool) between the shifter bezel and the top finish panel.

2. Use the tool to unsnap the shifter bezel

from the finish panel.

3. Locate the white lever located on the

left side of the shifter.

4. Using the tool move the white lever

towards the rear of the shifter.

Note: After you have assumed manual control with SelectShift your vehicle will remain in this mode until you return the gearshift lever from sport (S), back to drive (D). Upshift to the recommended shift speeds according to the following chart:

Upshifts when accelerating (recom-

mended for best fuel economy)

Shift from:

1 - 2
2 - 3
3 - 4
4 - 5
5 - 6

15 mph (24 km/h) 25 mph (40 km/h) 40 mph (64 km/h) 45 mph (72 km/h) 50 mph (80 km/h)

The instrument cluster will display the selected gear that you are currently in and a shift indicator arrow to assist in optimizing shifting. SelectShift will automatically make some shifts for you in the event that your engine speed is running at too high, or too low an RPM. Note: Engine damage may occur if excessive engine revving is held without shifting. Brake-Shift Interlock WARNINGS

Do not drive your vehicle until you verify that the brake lamps are working.

143

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E142627Transmission

5. While holding the white lever in the rear position, move the shifter from the park position.

6. Press the shifter bezel back into the top

finish panel until it snaps back into position.

7. Apply the brake pedal, start the vehicle

and release the parking brake.

Note: See your authorized dealer as soon as possible if this procedure is used. If Your Vehicle Gets Stuck In Mud or Snow Note: Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Note: Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat. If your vehicle gets stuck in mud or snow, it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern. Press lightly on the accelerator in each gear.

144

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Four-Wheel Drive (If Equipped)

PRINCIPLE OF OPERATION This system is a proactive system. It has the ability to anticipate wheel slip and transfer torque to the rear wheels before slip occurs. Even when wheel slip is not present, the system is continuously making adjustments to the torque distribution, in an attempt to improve straight line and cornering behavior, both on and off road. The system automatically turns on every time you switch the ignition on. All components of the system are sealed and do not require maintenance. USING FOUR-WHEEL DRIVE Note: When a system malfunction is present, a warning message will be displayed in the information display. See General Information (page 93). This means the system is not functioning correctly and has defaulted to front-wheel drive only. Have your vehicle checked by an authorized dealer. Note: A message will be displayed in the information display when the system overheats and switches to front-wheel drive. This condition may occur if you operate your vehicle in extreme high load conditions or with excessive wheel slip, (i.e. deep sand). To resume four-wheel drive function as soon as possible, stop your vehicle in a safe location and switch the ignition off. After the system cools and normal four-wheel drive functionality resumes, a message will be displayed for approximately five seconds. Note: If a warning message appears in the information display when using the spare tire, it should turn off after reinstalling the repaired or replaced road tire and you switch the ignition on.

Note: It is recommended that you reinstall the repaired tire or replace the tire as soon as possible. Major dissimilar tire sizes between the front and rear axles could cause system damage or default the system to front-wheel drive. The system gives your vehicle some limited off-road capabilities. Operating your vehicle in conditions other than moderate sand, snow, mud or rough roads could subject it to excessive stress and heat which could result in system damage. This will not be covered by your vehicle warranty.

A graphic will be displayed in the information display to advise you of the power distribution between the front and rear wheels. The more the area is filled the more power is being distributed to that wheel. Driving in Special Conditions With Four-Wheel Drive Four-wheel drive vehicles are suitable for driving on sand, snow, mud and rough roads and have operating characteristics that are somewhat different from conventional vehicles, both on and off the freeway. Note: It may be useful to switch Traction control off. This allows for more wheel spin and engine torque in certain off road conditions or if your vehicle becomes stuck.

145

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E142669Four-Wheel Drive (If Equipped)

in loss of vehicle control. Apply smooth pressure to the accelerator pedal or brake pedal when changes in vehicle speed are required. Avoid abrupt steering, acceleration and braking. This could result in an increased risk of vehicle roll over, loss of vehicle control and personal injury. Use all available road surface to bring your vehicle to a safe direction of travel. In the event of an emergency stop, avoid skidding the tires and do not attempt any sharp steering wheel movements. If your vehicle goes from one type of surface to another (i.e. from concrete to gravel) there will be a change in the way your vehicle responds to a maneuver (i.e. steering, acceleration or braking). Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid excessive wheel slip. Do not drive your vehicle in deep sand for an extended period of time. This will cause the system to overheat. A message will be displayed in the information display. See General Information (page 93). To resume operation, switch the ignition off and allow the system to cool down for a minimum of 15 minutes. After the system has cooled down, a message will be displayed briefly in the information display. See General Information (page 93). When driving at slow speeds in deep sand under high outside temperatures, use a low gear when possible. Low gear operation will maximize the engine and transmission cooling capability.

When driving at slow speeds off road under high load conditions, use a low gear when possible. Low gear operation will maximize the engine and transmission cooling capability. Under severe operating conditions, the air conditioning may cycle on and off to prevent the engine from overheating. Basic Operating Principles • Drive slower in strong crosswinds which

can affect the normal steering characteristics of your vehicle.

• When driving your vehicle on surfaces

made slippery by loose sand, water, gravel, snow or ice proceed with care.

If Your Vehicle leaves the Road If your vehicle leaves the road, reduce your vehicle speed and avoid severe braking. When your vehicle speed has been reduced ease your vehicle back onto the road. Do not turn the steering wheel sharply while returning your vehicle to the road. It may be safer to stay on the shoulder of the road and slow down gradually before returning to the road. You may lose control if you do not slow down or if you turn the steering wheel too sharply or abruptly. It may be less risky to strike small objects, such as freeway reflectors, with minor damage to your vehicle rather than attempt a sudden return to the road which could cause your vehicle to slide sideways out of control or roll over. Remember, your safety and the safety of others should be your primary concern. Emergency Maneuvers In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid over-driving your vehicle (i.e. turn the steering wheel only as rapidly and as far as required to avoid the emergency). Excessive steering can result

146

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Four-Wheel Drive (If Equipped)

Driving on Hilly or Sloping Terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. Note: Avoid turning on steep slopes or hills. A danger lies in losing traction, slipping sideways and possible vehicle roll over. Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side. Do not drive in reverse over a hill without the aid of an observer. When climbing a steep slope or hill, start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started. This reduces strain on the engine and the possibility of stalling. If your vehicle stalls, do not try to turn around because this could cause vehicle roll over. It is better to reverse back to a safe location. Apply just enough power to the wheels to climb the hill. Too much power will cause the tires to slip, spin or lose traction, resulting in loss of vehicle control.

Avoid driving at excessive speeds, this causes vehicle momentum to work against you and your vehicle could become stuck to the point that assistance may be required from another vehicle. Remember, you may be able to back out the way you came if you proceed with caution. Mud and Water Mud Be cautious of sudden changes in vehicle speed or direction when you are driving in mud. Even four-wheel drive vehicles can lose traction in slick mud. If your vehicle does slide, steer in the direction of the slide until you regain control of your vehicle. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts can cause an imbalance that could damage drive components. Water If you must drive through high water, drive slowly. Traction or brake capability may be limited. When driving through water, determine the depth and avoid water higher than the bottom of the wheel rims. If the ignition system gets wet, your vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop your vehicle as effectively as dry brakes. Drying can be improved by applying light pressure to the brake pedal while moving slowly. Note: Driving through deep water may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant and power transfer unit lubricant should be checked and changed if necessary.

147

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E143949Four-Wheel Drive (If Equipped)

Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral. Disengage overdrive or move the transmission selector lever to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control. The front wheels have to be turning in order to steer your vehicle. Your vehicle has anti-lock brakes, therefore apply the brakes steadily. Do not pump the brake pedal. Driving on Snow and Ice WARNING

If you are driving in slippery conditions that require tire chains or cables, then it is critical that you drive

cautiously. Keep speeds down, allow for longer stopping distances and avoid aggressive steering to reduce the chances of a loss of vehicle control which can lead to serious injury or death. If the rear end of your vehicle slides while cornering, steer in the direction of the slide until you regain control of your vehicle.

Note: Excessive tire slippage can cause transmission damage. Four-wheel drive vehicles have advantages over two-wheel drive vehicles in snow and ice but can skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control. Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop.

Avoid sudden braking. Although a four-wheel drive vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it will not stop any faster as braking occurs at all four wheels. Do not become overconfident as to road conditions. Make sure you allow sufficient distance between you and other vehicles for stopping. Drive slower than usual and consider using one of the lower gears. In emergency stopping situations, apply the brake steadily. As your vehicle has a four wheel anti-lock brake system, do not pump the brake pedal. See Hints on Driving With Anti-Lock Brakes (page 150). If Your Vehicle Gets Stuck In Mud or Snow If your vehicle gets stuck in mud or snow, it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern. Press lightly on the accelerator in each gear. Note: Do not rock your vehicle if the engine is not at normal operating temperature, damage to the transmission may occur. Note: Do not rock your vehicle for more than a minute, damage to the transmission and tires may occur or the engine may overheat. Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty. For this reason, we strongly recommend that you do not make modifications such as adding or removing parts (i.e. lift kits or stabilizer bars) or by using replacement parts not equivalent to the original factory equipment.

148

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Four-Wheel Drive (If Equipped)

We recommend that you use caution when your vehicle has either a high load or device (i.e. ladder or luggage racks). Any modifications to your vehicle that raise the center of gravity may cause your vehicle to roll over when there is a loss of vehicle control. Failure to maintain your vehicle correctly may void the warranty, increase your repair cost, reduce vehicle performance and operational capabilities and adversely affect you and your passenger's safety. We recommend you frequently inspect your vehicle's chassis components when your vehicle is subject to off road usage.

149

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Brakes

Emergency Brake Assist Emergency brake assist detects when you brake heavily by measuring the rate at which you press the brake pedal. It provides maximum braking efficiency as long as you press the pedal. Emergency brake assist can reduce stopping distances in critical situations. Anti-lock Brake System This system helps you maintain steering control during emergency stops by keeping the brakes from locking.

This lamp momentarily illuminates when you switch the ignition on. If the light does not illuminate during start up, remains on or flashes, the anti-lock braking system may be disabled. Have the system checked by an authorized dealer. If the anti-lock brake system is disabled, normal braking is still effective.

If the brake warning lamp illuminates with the parking brake released, have your brake

system serviced immediately.

HINTS ON DRIVING WITH ANTI-LOCK BRAKES Note: When the system is operating, the brake pedal will pulse and may travel further. Maintain pressure on the brake pedal. You may also hear a noise from the system. This is normal. The anti-lock braking system will not eliminate the risks when: •

You drive too closely to the vehicle in front of you. Your vehicle is hydroplaning. You take corners too fast. The road surface is poor.

GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out and an authorized dealer should check them. If the vehicle has continuous vibration or shudder in the steering wheel while braking, an authorized dealer should check your vehicle. Note: Brake dust may accumulate on the wheels, even under normal driving conditions. Some dust is inevitable as the brakes wear and does not contribute to brake noise. See Cleaning the Alloy Wheels (page 240).

See Warning Lamps and Indicators (page 89).

Wet brakes result in reduced braking efficiency. Gently press the brake pedal a few times when driving from a car wash or standing water to dry the brakes. Brake Over Accelerator In the event the accelerator pedal becomes stuck or entrapped, apply steady and firm pressure to the brake pedal to slow the vehicle and reduce engine power. If you experience this condition, apply the brakes and bring your vehicle to a safe stop. Switch the engine off, move the transmission to park (P) and apply the parking brake. Inspect the accelerator pedal and the area around it for any items or debris that may be obstructing its movement. If none are found and the condition persists, have your vehicle towed to the nearest authorized dealer.

• • •

150

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E138644E138644Brakes

WARNINGS

You must remain in your vehicle when the system turns on. At all times, you are responsible for

controlling your vehicle, supervising the system and intervening, if required. Failure to take care may result in the loss of control of your vehicle, serious personal injury or death.

The system will turn off if a malfunction is apparent or if you rev the engine excessively. Failure to

take care may result in the loss of control of your vehicle, serious personal injury or death.

The system makes it easier to pull away when your vehicle is on a slope without the need to use the parking brake. When the system is active, your vehicle remains stationary on the slope for two to three seconds after you release the brake pedal. This allows time to move your foot from the brake to the accelerator pedal. The system releases the brakes automatically once the engine has developed sufficient drive to prevent your vehicle from rolling down the slope. This is an advantage when pulling away on a slope, for example from a car park ramp, traffic lights or when reversing uphill into a parking space. Note: The system only functions when you bring your vehicle to a complete standstill in an uphill gear (for example, drive when facing uphill or reverse when facing downhill). Note: There is no warning light to indicate the system is either on or off. Using Hill Start Assist 1. Press the brake pedal to bring your

vehicle to a complete standstill. Keep the brake pedal pressed.

PARKING BRAKE

WARNING

Always set the parking brake fully and make sure you shift the gearshift lever to park (P). Switch the ignition off and remove the key whenever you leave your vehicle.

Note: Do not press the release button while pulling the lever up. To apply the parking brake: 1. Press the foot brake pedal firmly. 2. Pull the parking brake lever up to its

fullest extent.

Note: If you park your vehicle on a hill and facing uphill, shift the gearshift lever to park (P) and turn the steering wheel away from the curb. Note: If you park your vehicle on a hill and facing downhill, shift the gearshift lever to park (P) and turn the steering wheel toward the curb. To release the parking brake: 1. Press the brake pedal firmly. 2. Pull the lever up slightly. 3. Press the release button and push the

lever down.

HILL START ASSIST WARNINGS

The system does not replace the parking brake. When you leave your vehicle, always apply the parking

brake. Failure to leave your vehicle securely parked may lead to a crash or injury. See Parking Brake (page 151).

151

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Brakes

2.

If the sensors detect that your vehicle is on a slope, the system activates automatically.

3. When you remove your foot from the brake pedal, your vehicle remains on the slope without rolling away for about two to three seconds. This hold time automatically extends if you are in the process of driving off.

4. Drive off in the normal manner. The

system releases the brakes automatically.

Note: When you remove your foot from the brake pedal and press the pedal again when the system is active, you will experience significantly reduced brake pedal travel. This is normal. Switching the System On and Off Vehicles with Manual Transmission You can switch this feature on or off in the information display. The system remembers the last setting when you start your vehicle. Vehicles with Automatic Transmission You cannot turn the system on or off. When you switch the ignition on, the system automatically turns on.

152

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Traction Control

PRINCIPLE OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. If your vehicle begins to slide, the system applies the brakes to individual wheels and, when needed, reduces engine power at the same time. If the wheels spin when accelerating on slippery or loose surfaces, the system reduces engine power in order to increase traction. USING TRACTION CONTROL

WARNING

The stability and traction control light illuminates steadily if a failure is detected in the system. Verify that

the traction control system was not manually disabled using the information display controls or the switch. If the stability control and traction control light is still illuminating steadily, have the system serviced by an authorized dealer immediately. Operating your vehicle with the traction control disabled could lead to an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.

The system automatically turns on each time you switch the ignition on. If your vehicle is stuck in mud or snow, switching traction control off may be beneficial as this allows the wheels to spin. Note: When you switch traction control off, stability control remains fully active. Switching the System Off When you switch the system off or on, a message appears in the information display showing system status. You can switch the system off by either using the information display controls or the switch.

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Using the Information Display Controls You can switch this feature off or on in the information display. See General Information (page 93). Using a Switch (If Equipped) The switch for the stability control system and traction control system is located on the instrument panel. Use the switch to turn the system off or on. System Indicator Lights and Messages

The stability and traction control light temporarily illuminates on engine start-up and flashes

when a driving condition activates either of the systems.

The stability and traction control off light temporarily illuminates on engine start-up and stays on:

• When you turn the traction control

system off. If a problem occurs in either of the systems.

•

153

E138639Stability Control

If a driving condition activates either the stability control or the traction control system you may experience the following conditions: •

The stability and traction control light flashes. Your vehicle slows down.

• • Reduced engine power. • A vibration in the brake pedal. • •

The brake pedal is stiffer than usual. If the driving condition is severe and your foot is not on the brake, the brake pedal may move as the systems applies higher brake forces.

The stability control system has several features built into it to help you maintain control of your vehicle: Electronic Stability Control The system enhances your vehicle’s ability to prevent skids or lateral slides by applying brakes to one or more of the wheels individually and, if necessary, reducing engine power. Roll Stability Control The system enhances your vehicle’s ability to prevent rollovers by detecting your vehicle’s roll motion and the rate at which it changes by applying the brakes to one or more wheels individually.

PRINCIPLE OF OPERATION

WARNINGS

Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and wheel and tire size may change the handling characteristics of your vehicle and may adversely affect the performance of the electronic stability control system. In addition, installing any stereo loudspeakers may interfere with and adversely affect the electronic stability control system. Install any aftermarket stereo loudspeaker as far as possible from the front center console, the tunnel, and the front seats in order to minimize the risk of interfering with the electronic stability control sensors. Reducing the effectiveness of the electronic stability control system could lead to an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.

Remember that even advanced technology cannot defy the laws of physics. It’s always possible to lose control of a vehicle due to inappropriate driver input for the conditions. Aggressive driving on any road condition can cause you to lose control of your vehicle increasing the risk of personal injury or property damage. Activation of the electronic stability control system is an indication that at least some of the tires have exceeded their ability to grip the road; this could reduce the operator’s ability to control the vehicle potentially resulting in a loss of vehicle control, vehicle rollover, personal injury and death. If your electronic stability control system activates, SLOW DOWN.

The system automatically turns on each time you switch the ignition on.

154

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Stability Control

Traction Control The system enhances your vehicle’s ability to maintain traction of the wheels by detecting and controlling wheel spin. See Using Traction Control (page 153).

Vehicle without stability control skidding off its intended route. Vehicle with stability control maintaining control on a slippery surface.

USING STABILITY CONTROL AdvanceTrac® with Roll Stability Control™ (RSC®) The system automatically activates when you start your vehicle. The AdvanceTrac with RSC system cannot be completely turned off, but the electronic stability control and roll stability control portions of the system are disabled when the transmission is in position R. You can turn off the traction control portion of the system independently. See Using Traction Control (page 153).

155

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E72903AAABBBBParking Aids

Note: If your vehicle is equipped with MyKey®, it is possible to prevent turning the sensing system off. See MyKey™ (page 54). The sensing system warns the driver of obstacles within a certain range of the bumper area. The system turns on automatically whenever the ignition is switched on. When receiving a detection warning, the radio volume is reduced to a predetermined level. After the warning goes away, the radio volume returns to the previous level. Rear Sensing System The rear sensors are only active when the transmission is in R (Reverse). As the vehicle moves closer to the obstacle, the rate of the audible warning increases. When the obstacle is fewer than 12 inches (30 centimeters) away, the warning sounds continuously. If a stationary or receding object is detected farther than 12
inches (30 centimeters) from the side of the vehicle, the tone sounds for only three seconds. Once the system detects an object approaching, the warning sounds again.

PARKING AID (If Equipped)

WARNINGS

To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at parking speeds. Traffic control systems, inclement weather, air brakes, and external motors and fans may also affect the function of the sensing system; this may include reduced performance or a false activation.

To help avoid personal injury, always use caution when in R (Reverse) and when using the sensing system. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.

Certain add-on devices such as large trailer hitches, bike or surfboard racks and any device that may block the

normal detection zone of the system, may create false beeps.

Note: Keep the sensors, located on the bumper or fascia, free from snow, ice and large accumulations of dirt. If the sensors are covered, the system’s accuracy can be affected. Do not clean the sensors with sharp objects. Note: If your vehicle sustains damage to the bumper or fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms.

156

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Parking Aids

Coverage area of up to 27 inches (70 centimeters) from the front of the vehicle and about 14
inches (35 centimeters) to the side of the front end of the vehicle. Refer to the reverse sensing section for details on coverage area.

The system sounds an audible warning when obstacles are near either bumper in the following manner: • Objects detected by the front sensors

are indicated by a high-pitched tone from the front radio speakers.

•

• Objects detected by the rear sensors are indicated by a lower pitched tone from the rear radio speakers. The sensing system reports the obstacle which is closest to the front or rear of the vehicle. For example, if an obstacle is 24 inches (60
centimeters) from the front of the vehicle and, at the same time, an obstacle is only 16 inches (40
centimeters) from the rear of the vehicle, the lower pitched tone sounds.

• An alternating warning sounds from the front and rear if there are objects at both bumpers that are closer than 10 inches (25 centimeters).

Coverage area of up to 6 feet (1.8 meters) from the rear bumper. There is decreased coverage area at the outer corners of the bumper.

The system detects certain objects while the transmission is in R (Reverse): •

and moving toward a stationary object at a speed of 3 mph (5 km/h) or less but not moving, and a moving object is approaching the rear of the vehicle at a speed of 3 mph (5 km/h) or less

•

The system can be switched off through the information display. If a fault is present in the system, a warning message appears in the information display and does not allow the driver to switch the faulted system on. Front Sensing System The front sensors are active when the gearshift is in any position other than P (Park) or N (Neutral) and the vehicle speed is below 6 mph (10 km/h).

157

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E130178E130382AParking Aids

The system may not function correctly if something passes between the front bumper and the parking space (i.e. a pedestrian or cyclist) or if the edge of the neighboring parked vehicle is high from the ground (i.e. a bus, tow truck or flatbed truck). Note: The sensors may not detect objects in heavy rain or other conditions that cause disruptive reflections. Note: The sensors may not detect objects with surfaces that absorb ultrasonic waves. Note: After a tire change the system will go through a relearning procedure. During this time the system performance may deteriorate. The system should not be used if: •

a foreign object (i.e. bike rack or trailer) is attached to the front or rear of the vehicle or at another location close to the sensors. an overhanging object (i.e. surfboard) is attached to the roof. the front bumper or side sensors are damaged (i.e. in a collision) or obstructed by a foreign object (i.e. front bumper cover). • a mini-spare tire is in use. Using Active Park Assist

•

•

For specific information on the reverse sensing portion of the system, refer to that section.

Press the button to switch the system off. It will remain off for the entire ignition cycle. The system can also be switched off through the information display. ACTIVE PARK ASSIST (If Equipped)

WARNING

This system is designed to be a supplementary park aid. It may not work in all conditions and is not

intended to replace the driver’s attention and judgment. The driver is responsible for avoiding hazards and maintaining a safe distance and speed, even when the system is in use.

Note: The driver is always responsible for controlling the vehicle, supervising the system and intervening if required. The system detects an available parallel parking space and automatically steers the vehicle into the space (hands-free) while you control the accelerator, gearshift and brakes. The system visually and audibly instructs you to park the vehicle.

158

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E142434E142733Parking Aids

Press the button. The touch screen displays a message and a corresponding graphic to indicate it's searching for a parking space. Use the turn signal to indicate which side of the vehicle you want

the system to search on. Note: If the turn signal is not on, the system automatically searches on the vehicle's passenger side.

When a suitable space is found, the touch screen displays a message and a chime sounds. Slow down and stop at approximately position (A), then follow the instructions on the touch screen. Note: You must observe that the selected space remains clear of obstructions at all times in the maneuver. Note: Vehicles with overhanging loads (e.g. a bus or a truck), street furniture and other items may not be detected by active park assist. You must make sure the selected space is suitable for parking. Note: The vehicle should be driven as parallel to other vehicles as possible while passing a parking space. Note: The system always offers the last detected parking space (i.e. if the vehicle detects multiple spaces while you are driving, it offers the last one). Note: If driven above approximately 20
mph (35 km/h), the touch screen shows a message to alert you to reduce vehicle speed.

Automatic Steering into Parking Space Note: If vehicle speed exceeds 6 mph (10
km/h), the system switches off and you need to take full control of the vehicle. Note: If a maneuver is interrupted before completion, the system switches off. The steering wheel position will not indicate the actual position of the steering and you have to full take control of the vehicle. With your hands off the wheel (and nothing obstructing its movement) and the transmission in R (Reverse), the vehicle steers itself as instructions to safely move the vehicle back and forward in the space are displayed in the touch screen. While reversing, the touch screen displays a message instructing you to check your surroundings (for safety reasons) and to back-up slowly, accompanied by a corresponding graphic.

159

Escape (TM2) Canada/United States of America, enUSA, Second Printing

AE130107Parking Aids

When you think the vehicle has enough space in front and behind it, or you hear a solid tone from the parking aid, bring the vehicle to a complete stop.

When automatic steering is finished, the touch screen displays a message indicating that the active park assist process is done. The driver is responsible for checking the parking job and making any necessary corrections before putting the transmission in P (Park). Deactivating the Park Assist Feature The system can be deactivated manually by: • • •

pressing the active park assist button grabbing the steering wheel driving above approximately 20 mph (35 km/h) for 30 seconds during an active park search

160

Escape (TM2) Canada/United States of America, enUSA, Second Printing

•

driving above 6 mph (10 km/h) during automatic steering turning off the traction control system.

• Certain vehicle conditions can also deactivate the system, such as: •

Traction control has activated on a slippery or loose surface. There is an anti-lock brake system