2014 Ford EDGE Owners Manual

— —

20A*

5A* — —

15A*

Brake on/off switch Stop lamps Rear seat release Air conditioner clutch Trailer tow stop/turn lamps relay Rear wiper motor Fuel pump Powertrain control module relay Vehicle power #2
Vehicle power #4
Vehicle power #1 (3.5/3.7L engines) Vehicle power #1 (2.0L engine) Air conditioner relay, Vehicle power #3, All-wheel drive module (3.5/3.7L engines), Active grille shutter (2.0L engine) Not used Not used Not used Not used Air conditioner clutch diode (3.5/3.7L engines) Not used Trailer tow park lamps relay Right high-intensity discharge headlamps Adaptive cruise control Not used Not used Rear washer

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Fuses

265

Fuse or relay

number

Fuse amp

rating

Protected components

83
84
85
86

87
88
89

90

91

92
93
94

95
96

97

98

—

20A*

—

7.5A*

5A* — — 5A*

10A*

10A*

5A*

10A* 5A* 30A**

— —

—

—

Not used Trailer tow park lamps Not used Powertrain control module relay, Powertrain control module keep-alive (3.5/3.7L engines) Run/start relay Run/start relay Not used Headlamp leveling motors (China only) Powertrain control module, Transmission Control Module (2.0L engine) Adaptive cruise control (3.5/3.7L engines) Automatic transmission warm-up (2.0L engine) Anti-lock brake system module Blower motor/rear defroster relay Passenger compartment fuse panel run/start Not used Canister purge solenoid diode (2.0L engine) Automatic transmission warm-up diode (2.0L engine) Air conditioner clutch relay

* Mini Fuses ** Cartridge Fuses

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

266

Fuses

Passenger Compartment Fuse Panel The fuse panel is located behind a trim panel on the left side of the driver’s footwell near the parking brake. To remove the trim panel, slide the release lever to the right then pull the trim panel out. To remove the fuse panel cover, press in the tabs on both sides of the cover, then pull the cover off. To reinstall the fuse panel cover, place the top part of the cover on the fuse panel, then push the bottom part of the cover until it clicks into place. Gently pull on the cover to make sure it is secure. To reinstall the trim panel, align the tabs on the bottom of the panel with the grooves, push the panel shut and slide the release lever to the left to secure the panel. To remove a fuse, use the fuse puller tool provided on the fuse panel cover.

10

11

12

13

14

15

16

17

18

19

20

21

49

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

48

40

41

42

43

44

45

46

47

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Fuses

267

Fuse or relay

number

Fuse amp

rating

Protected components

10
11

12

13
14
15

16
17
18

19
20

21

30A 15A 30A 10A 20A 5A 7.5A

10A 10A 10A 10A

15A

15A 15A 15A

10A 10A 10A

20A 20A

10A

Driver front smart window Not used (spare) Not used (spare) Demand lamps relay Not used (spare) Radio frequency module Power mirror switch, Memory seat switch, Driver seat module Not used (spare) Power liftgate Run/accessory relay Instrument panel cluster, Heads-up display Interior lighting, Puddle lamps, Backlighting Right turn signals Left turn signals Reverse lamps, Stop lamps, High-mounted stop lamps Low beam headlamps (right) Low beam headlamps (left) Keypad illumination, Brake shift interlock, Start button LED, Passive anti-theft system, Powertrain control module wake-up, Second row power enable Amplifier (Sony) Lock/unlock relays – vehicles without intelligent access Not used (spare)

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

268

Fuses

Fuse or relay

number

Fuse amp

rating

Protected components

22
23

24
25
26
27
28

29

30

31
32

33
34

35

36
37

38
39

20A 15A

15A 15A 5A 20A 15A

20A

15A

5A 15A

10A 10A

5A

10A 10A

10A 15A

Horn relay Steering wheel control, Intelligent access, Headlamp switch On-board diagnostics Liftgate release Global positioning system module Intelligent access Ignition switch (without intelligent access), Key inhibit solenoid, Push button start (with intelligent access) Radio, Multi-function display screen, Electronic finish panel, SYNC module Front park lamps, Auxiliary park lamps Not used (spare) Lock switch backlighting, Moonroof, Power windows (driver front), Compass/auto-dimming rear view mirror Not used (spare) Reverse sensing system, Rearview camera, Blind spot monitor Heads-up display, Headlamp leveling Not used (spare) Climate control (3.5L/3.7L engines) Not used (spare) High beam headlamps

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Fuses

269

Fuse or relay

Fuse amp

Protected components

number

40

41

42

43
44
45
46
47
48

49

rating

10A

7.5A

5A

10A 10A 5A 10A 15A

30A Circuit

Breaker

Rear park lamps, license plate lamps Occupant classification sensor, Restraints control module Grade assist control switch (2.0L engine) Not used (spare) Not used (spare) Not used (spare) Climate control LED signal mirrors Power windows

—

Delayed accessory relay

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

270

Maintenance

GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized dealers who are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly. They are supported by a wide range of highly specialized tools developed specifically for servicing your vehicle. To help you service your vehicle, we provide Scheduled Maintenance Information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your warranty information to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Motorcraft® parts are designed and built to provide the best performance in your vehicle.

Precautions • Do not work on a hot engine. • Make sure that nothing gets caught in moving parts. • Do not work on a vehicle with the engine running in an enclosed • Keep all open flames and other burning material (such as cigarettes)

space, unless you are sure you have enough ventilation.

away from the battery and all fuel related parts.

Working with the Engine Off 1. Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key (if equipped). 3. Block the wheels.

Working with the Engine On

WARNING: To reduce the risk of vehicle damage or personal burn injuries, do not start your engine with the air cleaner

removed and do not remove it while the engine is running.

1. Set the parking brake and shift to position P (Park). 2. Block the wheels.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

271

OPENING AND CLOSING THE HOOD

1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel near the steering column.

2. Go to the front of the vehicle and release the secondary hood latch that is located under the front center of the hood.

3. Lift the hood and support it with the prop rod. Note: Make sure the hood is properly closed.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

272

Maintenance

UNDER HOOD OVERVIEW

3.5L V6 engine shown, 3.7L V6 engine similar

C D

A. Engine coolant reservoir B. Power steering fluid reservoir C. Engine oil filler cap D. Engine oil dipstick E. Brake fluid reservoir F. Battery G. Power distribution box H. Air filter assembly I. Windshield washer fluid reservoir

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

273

2.0L EcoBoost engine

A. Engine coolant reservoir B. Power steering fluid reservoir C. Engine oil dipstick D. Engine oil filler cap E. Brake fluid reservoir F. Battery G. Power distribution box H. Air filter assembly I. Windshield washer fluid reservoir

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

274

Maintenance

ENGINE OIL DIPSTICK

2.0L EcoBoost

A. MIN B. MAX

A. MIN B. MAX

3.5L, 3.7L and 3.5L EcoBoost

ENGINE OIL CHECK Note: Check the level before starting the engine. Note: Make sure that the level is between the MIN and MAX marks. 1. Make sure that your vehicle is on level ground. 2. Turn the engine off and wait 10 minutes for the oil to drain into the oil pan. 3. Remove the dipstick and wipe it with a clean, lint-free cloth. Replace the dipstick and remove it again to check the oil level. If the level is at the MIN mark, add oil immediately.

Adding Engine Oil Note: Do not remove the filler cap when the engine is running. Note: Do not add engine oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

275

Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricants Specification Advisory Council (ILSAC), comprised of U.S. and Japanese automobile manufacturers.

1. Remove the filler cap. 2. Add engine oil that meets Ford specifications. See Capacities and Specifications for more information. 3. Replace the filler cap. Turn it until you feel a strong resistance.

ENGINE COOLANT CHECK

Checking the Engine Coolant The concentration and level of engine coolant should be checked at the intervals listed in Scheduled Maintenance Information. Note: Make sure that the level is between the COLD FILL RANGE marks on the coolant reservoir. Note: Coolant expands when it is hot. The level may extend beyond the upper COLD FILL RANGE mark. Note: If the level is at the lower COLD FILL RANGE mark, below the lower COLD FILL RANGE mark, or empty, add coolant immediately. See Adding Engine Coolant in this chapter. The coolant concentration should be maintained within 48% to 50% which equates to a freeze point between -30 °F (-34 °C) and -34 °F (-37 °C). Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool ROB75240 available from your dealer. Ford does not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations. Note: Automotive fluids are not interchangeable; do not use engine coolant/antifreeze or windshield washer fluid outside of its specified function and vehicle location.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

276

Maintenance

Adding Engine Coolant

WARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system

can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.

WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant

could make it difficult to see through the windshield.

WARNING: To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly.

WARNING: Do not add coolant further than the MAX mark.

Note: Do not use stop leak pellets, cooling system sealants or additives as they can cause damage to the engine cooling or heating systems. This damage would not be covered under your vehicle’s warranty. Note: During normal vehicle operation, the engine coolant may change color from orange to pink or light red. As long as the engine coolant is clear and uncontaminated, this color change does not indicate the engine coolant has degraded nor does it require the engine coolant to be drained, the system to be flushed, or the engine coolant to be replaced. • DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine coolants may harm your engine’s cooling system. The use of an improper coolant may harm engine and cooling system components and may void the warranty. • In case of emergency, a large amount of water without engine coolant may be added in order to reach a vehicle service location. In this instance, the cooling system must be drained, chemically cleaned with Motorcraft Premium Cooling System Flush, and refilled with engine coolant as soon as possible. Water alone (without engine coolant) can cause engine damage from corrosion, overheating or freezing.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

277
• Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing. • Do not add extra inhibitors or additives to the coolant. These can be

harmful and compromise the corrosion protection of the engine coolant.

Unscrew the cap slowly. Any pressure will escape as you unscrew the cap. Add prediluted engine coolant meeting the Ford specification. See Capacities and Specifications for more information. Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary, add enough prediluted engine coolant to bring the coolant level to the proper level.

Recycled Engine Coolant Ford Motor Company does NOT recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available.

Used engine coolant should be disposed of in an appropriate

manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.

coolant concentration above 50%.

Severe Climates If you drive in extremely cold climates: • It may be necessary to have a Ford authorized dealer increase the • A coolant concentration of 60% will provide improved freeze point protection. Engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.

If you drive in extremely hot climates: • It may be necessary to have a Ford authorized dealer decrease the • A coolant concentration of 40% will provide improved overheat

coolant concentration to 40%.

protection. Engine coolant concentrations below 40% will decrease the corrosion/freeze protection characteristics of the engine coolant and may cause engine damage.

Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

278

Maintenance

Engine fluid temperature management (EcoBoost engine only)

WARNING: To reduce the risk of collision and injury, be prepared that the vehicle speed may reduce and the vehicle may

not be able to accelerate with full power until the fluid temperatures reduce.

Your vehicle has been designed to pull a trailer, but because of the added load, the vehicle’s engine may temporarily reach higher temperatures during severe operating conditions such as ascending a long or steep grade while pulling a trailer in hot ambient temperatures. At this time, you may notice your engine coolant temperature gauge needle move toward the H (hot) and the POWER REDUCED TO LOWER TEMP message may appear on the message center. You may notice a reduction in the vehicle’s speed caused by reduced engine power. Your vehicle has been designed to enter this mode if certain high temperature/high load conditions take place in order to manage the engine’s fluid temperatures. The amount of speed reduction will depend on the vehicle loading, towing, grade, ambient temperature, and other factors. If this occurs, there is no need to pull off the road. The vehicle can continue to be driven while this message is active. The air conditioning may also cycle on and off during severe operating conditions to protect overheating of the engine. When the engine coolant temperature decreases to a more normal operating temperature, the air conditioning will turn on once again. If you notice any of the following: • the engine coolant temperature gauge moves fully into the red (hot) • the coolant temperature warning light illuminates • the service engine soon indicator illuminates 1. Pull off the road as soon as safely possible and place the vehicle in P (Park). 2. Leave the engine running until the coolant temperature gauge needle moves away from the H range. After several minutes, if this does not happen, follow the remaining steps. 3. Turn the engine off and wait for it to cool before checking the coolant level.

area

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

279

WARNING: Never remove the coolant reservoir cap while the engine is running or hot.

4. If the coolant level is normal, you may restart your engine and continue on. 5. If the coolant is low, add coolant, restart the engine and take your vehicle to an authorized dealer. See Adding engine coolant in this chapter for more information. Refer to fail-safe cooling for additional information.

What You Should Know About Fail-Safe Cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The fail-safe distance depends on ambient temperatures, vehicle load and terrain. How Fail-Safe Cooling Works If the engine begins to overheat, the engine coolant temperature gauge will move to the red (hot) area and:

The coolant temperature warning light will illuminate.

The service engine soon indicator will illuminate.

If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature and the engine will completely shut down, causing steering and braking effort to increase. Once the engine temperature cools, the engine can be restarted. Take your vehicle to an authorized dealer as soon as possible to minimize engine damage.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

280

Maintenance

When Fail-Safe Mode is Activated

WARNING: Fail-safe mode is for use during emergencies only. Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs. When in fail-safe mode, the vehicle will have limited power, will not be able to maintain high-speed operation, and may completely shut down without warning, potentially losing engine power, power steering assist, and power brake assist, which may increase the possibility of a crash resulting in serious injury.

WARNING: Never remove the coolant reservoir cap while the engine is running or hot.

You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine. 2. Arrange for the vehicle to be taken to an authorized dealer. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low. 5. Restart the engine and take your vehicle to an authorized dealer. Note: Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to an authorized dealer as soon as possible.

TRANSMISSION FLUID CHECK

6F50 transmission (if equipped)

WARNING: The dipstick cap and surrounding components may be hot; gloves are recommended.

Note: Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is warmed up (approximately 20 miles [30 km]). If your vehicle has been operated for

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

281

an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off until normal operating temperatures are reached to allow the fluid to cool before checking. Depending on vehicle use, cooling times could take up to 30 minutes or longer. Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage. 1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3. With the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow a minimum of 10 seconds for each gear to engage. 4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Under hood overview in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube by turning it to the locked position. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal operating temperature. Low fluid level MAX

MIN

If the fluid level is below the MIN range of the dipstick, add fluid to reach the hash mark level. Note: If the fluid level is below the MIN level,

do not drive the vehicle. An underfill condition may cause shift and/or engagement concerns and/or possible damage. Correct fluid level The transmission fluid should be checked at normal operating temperature 180°F-200°F (82°C-93°C) on a level surface. The normal operating temperature can be reached after approximately 20 miles (30 km) of driving.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

282

Maintenance

The transmission fluid level should be targeted within the cross-hatch area if at normal operating temperature 180°F-200°F (82°C-93°C) .

High fluid level MAX

MIN

If the fluid level is above the MAX range of the dipstick, remove fluid to reach the hashmark level. Note: Fluid level above the MAX level may

cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off until normal operating temperatures are reached. Depending on vehicle use, cooling times could take up to 30 minutes or longer. Adjusting automatic transmission fluid levels Note: Use of a non-approved automatic transmission fluid may cause internal transmission component damage. Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Capacities and Specifications chapter.

MIN

MAX

If necessary, add fluid in 1/2 pint (250 ml) increments through the filler tube until the level is correct.

If an overfill occurs, excess fluid should be removed by an authorized dealer.

Note: An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

283

6F35 TRANSMISSION (if equipped) Note: Transmission fluid should be checked by an authorized dealer. If required, fluid should be added by an authorized dealer. The automatic transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, (i.e., if the transmission slips or shifts slowly) or if you notice some sign of fluid leakage. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components.

BRAKE FLUID CHECK Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately.

POWER STEERING FLUID CHECK Check the power steering fluid. Refer to scheduled maintenance information. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir. Refer to the Capacities and Specifications chapter for the proper fluid type.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

284

Maintenance

FUEL FILTER Your vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance or replacement is not needed.

WASHER FLUID CHECK

WARNING: If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze protection. Failure

to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.

Add fluid to fill the reservoir if the level is low. Only use a washer fluid that meets Ford specifications. See the technical specifications chart in the Capacities and Specifications chapter. Note: The front and rear washer systems are supplied from the same reservoir. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.

CHANGING THE VEHICLE BATTERY

WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.

WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

285

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.

Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.

WARNING: Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.

Your vehicle is equipped with a Motorcraft® maintenance-free battery which normally does not require additional water during its life of service. Note: If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time. To ensure proper operation of the battery management system (BMS), any electrical devices that are added to the vehicle should not have their ground connection made directly at the negative battery post. A connection at the negative battery post can cause inaccurate measurements of the battery condition and potential incorrect system operation. Note: Electrical or electronic accessories or components added to the vehicle by the dealer or the owner may adversely affect battery performance and durability and may also affect the performance of other electrical systems in the vehicle. When a battery replacement is required, the battery should only be replaced with a Ford recommended replacement battery that matches the electrical requirements of the vehicle.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

286

Maintenance

When the battery is disconnected or a new battery installed, the automatic transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly when first driven. This operation is considered normal and will fully update transmission operation to its optimum shift feel. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. Note: Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more to • Note: If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.

relearn the idle and fuel trim strategy.

If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

287

CHECKING THE WIPER BLADES

Run the tip of your fingers over the edge of the blade to check for roughness. Clean the wiper blades with washer fluid or water applied with a soft sponge or cloth.

CHANGING THE WIPER BLADES

1. Pull the wiper arm away from the vehicle. Turn the blade at an angle from the wiper arm. Press the lock tab to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard.

Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be improved by cleaning the wiper blades and the windshield. To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

288

Maintenance

Changing rear window wiper blade The rear wiper arm is designed without a service position. This reduces the risk of damage to the blade in an automatic car wash. To replace the wiper blade:

1. Grab the wiper arm with one hand close to the arm/blade joint and pull it as far away from the glass as possible. Do not use excessive force because it can break the wiper arm at the heel. Hold it there until the next step.

2. Grab the primary structure of the blade with the other hand close to the arm/blade joint. 3. Grip tightly and press on the arm/blade joint from beneath and separate the blade from the arm.

4. Attach the new wiper to the wiper arm and press it into place until a click is heard.

If you find this procedure too difficult, please see your dealer.

AIR FILTER CHECK

WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner

removed and do not remove it while the engine is running.

When changing the air filter element, use only the air filter element listed. Refer to Motorcraft® Part Numbers in the Capacities and Specifications chapter. For EcoBoost equipped vehicles: When servicing the air cleaner, it is important that no foreign material enter the air induction system. The engine and turbocharger are susceptible to damage from even small particles.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

289

Refer to Scheduled Maintenance for the appropriate intervals for changing the air filter element. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not used.

Changing the air filter element

1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing.

5. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated.

6. Replace the air filter housing cover and secure the clamps. Be sure that the air cleaner cover tabs are engaged into the slots of the air cleaner housing.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

290

Maintenance

ADJUSTING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident, an authorized dealer should check the alignment of your headlamps.

Vertical Aim Adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away.

• (1) 8 feet (2.4 meters) • (2) Center height of lamp to • (3) 25 feet (7.6 meters) • (4) Horizontal reference line

ground

2. Measure the height of the headlamp bulb center from the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height. 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other. For Vehicles with Halogen Headlamps:

On the wall or screen you will observe a flat zone of high intensity light located at the top of the right hand portion of the beam pattern. If the top edge of the high intensity light zone is not at the horizontal reference line, the headlamp will need to be adjusted.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

291

For Vehicles with HID Headlamps:

There is a distinct cut-off (change from light to dark) in the left portion of the beam pattern. The top edge of this cut-off should be positioned 2 inches (5 centimeters) below the horizontal reference line.

4. Locate the vertical adjuster on each headlamp. Using a Hex head driver, turn the adjuster either clockwise or counterclockwise in order to adjust the vertical aim of the headlamp.

5. Close the hood and turn off the lamps. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE.

CHANGING A BULB

Lamp Assembly Condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a thin film of mist can form on the interior of the lens. The thin mist eventually clears and exits through the vents during normal operation. Clearing time may take as long as 48 hours under dry weather conditions. These are examples of acceptable condensation: • Presence of thin mist (no streaks, drip marks or droplets). • Fine mist covers less than 50% of the lens.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

292

Maintenance

These are examples of unacceptable moisture (usually caused by a lamp water leak): • Water puddle inside the lamp. • Large water droplets, drip marks or streaks present on the interior of

the lens.

Take your vehicle to a dealer for service if any of the above conditions of unacceptable moisture are present. Replacing headlamp bulbs

WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. 1. Make sure that the headlamp control is in the off position. 2. Open the hood.

3. Remove the bulb cover.

4. Turn the bulb holder counterclockwise and remove it.

5. Disconnect the electrical connector. 6. Reverse the procedure to install the new bulb.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

293

Replacing HID headlamp bulbs (if equipped) The low beam headlamps on your vehicle use a “high intensity discharge” source. These lamps operate at a high voltage. When the bulb is burned out, the bulb and starter capsule assembly must be replaced by your authorized dealer. Replacing front parking lamp/turn signal bulbs 1. Make sure that the headlamp control is in the off position.

2. Open the hood. 3. Reach over the front bolster. 4. Rotate the bulb socket counterclockwise and remove from the lamp assembly. 5. Carefully pull the bulb out of the socket and push in the new bulb.

6. Install the bulb socket into the lamp assembly and rotate clockwise.

Replacing tail/stop/turn/sidemarker/backup lamp bulbs

1. Make sure the headlamp switch is in the off position, then open the liftgate to expose the lamp assembly bolts. 2. Remove the two bolts from the lamp assembly. 3. Carefully remove the lamp assembly away from the vehicle by pulling the assembly straight out to expose the bulb socket.

4. Rotate the bulb socket counterclockwise and remove from lamp assembly. 5. Pull bulb straight out of socket and snap in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. 7. Carefully install the tail lamp assembly on the vehicle by securing the lamp assembly with two bolts.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

294

Maintenance

Replacing high-mount brake lamp bulbs Your vehicle is equipped with an LED center high-mount stop lamp. It is designed to last the life of the vehicle. If replacement is required, see your authorized dealer. Replacing license plate lamp bulbs

1. Make sure the headlamp switch is in the off position. 2. Press the lever and carefully pry the license plate lamp assembly (located above the license plate) from the liftgate. 3. Rotate the bulb socket counterclockwise and remove from lamp assembly.

4. Pull bulb straight out of socket and push in the new bulb. 5. Install the bulb socket into the lamp assembly and rotate clockwise. 6. To install, carefully press the lamp assembly into the liftgate.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Maintenance

295

BULB SPECIFICATION CHART Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.

Function

Number of bulbs

Headlamp high/low beam (halogen) * HID (high intensity discharge) headlamp * Front sidemarker lamp Front park/turn signal lamp

Rear turn lamp

Stop/tail/sidemarker lamp

N/A

Trade number

HIR2

D3S

LED

3457NAK (amber) 3757NAK (amber)

3157K LCP or 3157K

N/A

Backup lamp License plate lamp * High-mount brake lamp Map lamp Second row dome/reading lamp Rear courtesy lamp Visor vanity lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer. * To replace these lamps - see your authorized dealer.

921
168
LED W5W

578
37

578

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

296

Vehicle Care

GENERAL INFORMATION Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes.

CLEANING PRODUCTS For best results, use the following products or products of equivalent quality: Motorcraft Bug and Tar Remover (ZC-42) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Detail Wash (ZC-3-A) Motorcraft Dusting Cloth (ZC-24) Motorcraft Engine Shampoo and Degreaser (United States only) (ZC-20) Motorcraft Engine Shampoo (Canada only) (CXC-66-A) Motorcraft Multi-Purpose Cleaner (Canada only) (CXC-101) Motorcraft Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft Premium Quality Windshield Washer Fluid (Canada only) [CXC-37-(A, B, D or F)] Motorcraft Premium Windshield Wash Concentrate with Bitterant (United States only) (ZC-32-B2) Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft Premium Leather and Vinyl Cleaner (ZC-56) Motorcraft Spot and Stain Remover (United States only) (ZC-14) Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23) Motorcraft Wheel and Tire Cleaner (ZC-37-A)

CLEANING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft® Detail Wash. • Never use strong household detergents or soap, such as dish washing

or laundry liquid. These products can discolor and spot painted surfaces.

• Never wash a vehicle that is hot to the touch or during exposure to • Dry the vehicle with a chamois or soft terry cloth towel in order to

strong, direct sunlight.

eliminate water spotting.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Vehicle Care

297
• Immediately remove items such as gasoline, diesel fuel, bird droppings and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time. Use Motorcraft Bug and Tar Remover. • Note: Suntan lotions and insect repellents can damage any painted

surface; if these substances come in contact with your vehicle, wash it off as soon as possible.

• Remove any exterior accessories before entering a car wash. Stripes or Graphics (if equipped) Do not use a commercial or high-pressure wand on the surface or edge of stripes and graphics. This can cause damage to the film and cause the edge of the film to peel away from the vehicle surface.

Exterior Chrome Note: Never use abrasive materials such as steel wool or plastic pads as they can scratch the chrome surface. Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers. • Wash the vehicle first, using cool or lukewarm water and a neutral pH • Use Motorcraft Custom Bright Metal Cleaner. Apply the product as

shampoo, such as Motorcraft Detail Wash.

you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag.

• Do not apply cleaning product to hot surfaces and do not leave

cleaning product on chrome surfaces for a period of time exceeding that which is recommended. • Note: Using other non-recommended cleaners can result in severe

and permanent cosmetic damage.

Underbody Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt.

Cleaning Plastic Exterior Parts Use only approved products to clean plastic parts. • For routine cleaning, use Motorcraft Detail Wash. • If tar or grease spots are present, use Motorcraft Bug and Tar Remover.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

298

Vehicle Care

WAXING Regular waxing is necessary to protect the paint on your car from the elements. We recommend that you wash and wax the painted surface once or twice a year. When washing and waxing, park your vehicle in a shaded area out of direct sunlight. Always wash your vehicle before applying wax. • Use a quality wax that does not contain abrasives. • Follow the manufacturer’s instructions to apply and remove the wax. • Apply a small amount of wax in a back-and-forth motion, not in • Do not allow wax to come in contact with any non-body (low-gloss black) colored trim. The wax discolors or stains the parts over time, such as: • Bumpers • Grained door handles • Side mouldings • Mirror housings • Windshield cowl area.

• Do not apply wax to glass areas. • After waxing, your car’s paint should feel smooth, and be free of

circles.

streaks and smudges.

spots, road salt and industrial fallout, before repairing paint chips.

REPAIRING MINOR PAINT DAMAGE Your authorized dealer has touch-up paint to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to an authorized dealer to make sure you get the correct color. • Remove particles, such as bird droppings, tree sap, insect deposits, tar • Always read the instructions before using the products. CLEANING THE ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The • Do not spray a hot engine with cold water to avoid cracking the

high-pressure fluid could penetrate the sealed parts and cause damage.

engine block or other engine components.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Vehicle Care

299

• Spray Motorcraft Engine Shampoo and Degreaser on all parts that

running engine may cause internal damage.

require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo. • Never wash or rinse the engine while it is hot or running; water in the • Never wash or rinse any ignition coil, spark plug wire or spark plug • Cover the battery, power distribution box, and air filter assembly to

well, or the area in and around these locations.

prevent water damage when cleaning the engine.

CLEANING THE WINDOWS AND WIPER BLADES The windows and wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. To clean these items, follow these tips: • The windows may be cleaned with a non-abrasive cleaner such as • The wiper blades can be cleaned with isopropyl (rubbing) alcohol or Motorcraft Premium Windshield Washer Concentrates in the U.S., or Motorcraft Premium Quality Windshield Washer Fluid in Canada. Replace your wiper blades when they appear worn or do not function properly.

Motorcraft® Ultra-Clear Spray Glass Cleaner.

• Do not use abrasive materials, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. If you cannot remove those streaks after cleaning with the glass cleaner or if the wipers chatter and move in a jerky motion, clean the outer surface of the windshield and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaning solution. After cleaning, rinse the windshield and wiper blades with clean water. The windshield is clean if beads do not form when you rinse the windshield with water. Note: Do not use sharp objects, such as a razor blade, to clean the inside of the rear window or to remove decals, as it may cause damage to the rear window defroster’s heated grid lines.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

300

Vehicle Care

CLEANING THE INTERIOR

WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt

webbing.

WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products

could contaminate the side airbag system and affect performance of the side airbag in a collision.

For fabric, carpets, cloth seats, safety belts and seats equipped with side airbags: • Remove dust and loose dirt with a vacuum cleaner. • Apply a layer of high quality foam cleaner, designed for automotive

interiors, to the dry stained area (s) of the item you are cleaning and allow soaking for one minute.

• If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover. In Canada, use Motorcraft Multi-Purpose Cleaner. • If a ring forms on the fabric after spot cleaning, clean the entire area • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.

immediately (but do not oversaturate) or the ring can set.

CLEANING THE INSTRUMENT PANEL AND INSTRUMENT CLUSTER LENS

WARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid

contamination of the airbag system.

Note: Follow the same procedure as cleaning leather seats for cleaning leather instrument panels and leather interior trim surfaces. See Cleaning Leather Seats in this chapter. Clean the instrument panel and cluster lens with a clean, damp, white, cotton cloth, then use a clean and dry, white, cotton cloth to dry these areas.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Vehicle Care

301
• Avoid cleaners or polishes that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.

• Be certain to wash or wipe your hands clean if you have been in contact with certain products, such as insect repellent and suntan lotion, in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the • Do not allow air fresheners and hand sanitizers to spill on interior surfaces. If a spill occurs, wipe off immediately. Damage may not be covered by your warranty.

finish of the instrument panel, interior trim and cluster lens.

If a staining liquid like coffee or juice has been spilled on the instrument panel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Use Motorcraft Premium Leather and Vinyl Cleaner or a commercially available leather cleaning product for automotive interiors. Test any cleaner or stain remover on an inconspicuous area. 3. Alternatively, wipe the surface with a damp, clean, white, cotton cloth and a mild soap and water solution. Dry the area with a clean, soft cloth. 4. If necessary, apply more soap and water solution or cleaning product to a clean, white, cotton cloth and press the cloth onto the soiled area. Allow this to set at room temperature for 30 minutes. 5. Remove the soaked cloth, then with a clean, damp cloth, use a rubbing motion for 60 seconds on the soiled area. 6. Following this, wipe area dry with a clean, white, cotton cloth.

CLEANING LEATHER SEATS (IF EQUIPPED) Note: Follow the same procedure as cleaning leather seats for cleaning leather instrument panels and leather interior trim surfaces. For routine cleaning, wipe the surface with a soft, damp cloth and a mild soap and water solution. Dry the area with a clean, soft cloth. For cleaning and removing spots and stains such as dye transfer, use Motorcraft Premium Leather and Vinyl Cleaner or a commercially available leather cleaning product for automotive interiors.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

302

Vehicle Care

Note: Test any cleaner or stain remover on an inconspicuous area. You should: • Remove dust and loose dirt with a vacuum cleaner. • Clean and treat spills and stains as soon as possible. Do not use the following products as these may damage the leather: • Oil and petroleum or silicone-based leather conditioners. • Household cleaners. • Alcohol solutions. • Solvents or cleaners intended specifically for rubber, vinyl and plastics. CLEANING THE ALLOY WHEELS Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers. A clearcoat paint finish coats aluminum wheels and wheel covers. In order to maintain their condition: • Clean weekly with Motorcraft Wheel and Tire Cleaner. Use a sponge to

remove heavy deposits of dirt and brake dust accumulation. Rinse thoroughly with a strong stream of water when you have completed the cleaning process.

• To remove tar and grease, use Motorcraft Bug and Tar Remover. • Never apply any cleaning chemical to hot or warm wheel rims or • Some automatic car washes may cause damage to the finish on your • Industrial-strength (heavy-duty) cleaners, or cleaning chemicals, in

wheel rims or covers.

covers.

combination with brush agitation to remove brake dust and dirt, could wear away the clearcoat finish over time.

• Do not use hydrofluoric acid-based or high caustic-based wheel • If you intend on parking your vehicle for an extended period after

cleaners, steel wool, fuels or strong household detergent.

cleaning the wheels with a wheel cleaner, drive your vehicle for a few minutes before doing so. This reduces the risk of increased corrosion of the brake discs.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Vehicle Care

303

VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time (30 days or more), read the following maintenance recommendations to make sure your vehicle stays in good operating condition. All motor vehicles and their components were engineered and tested for reliable, regular driving. Long-term storage under various conditions may lead to component degradation or failure unless specific precautions are taken to preserve the components. General • Store all vehicles in a dry, ventilated place. • Protect from sunlight, if possible. • If vehicles are stored outside, they require regular maintenance to

protect against rust and damage.

Body • Wash vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear-wheel housing and underside of front fenders. • Periodically wash vehicles stored in exposed locations. • Touch up raw or primed metal to prevent rust. • Cover chrome and stainless steel parts with a thick coat of auto wax

grade oil.

to prevent discoloration. Re-wax as necessary when the vehicle is washed.

• Lubricate hood latch, all door latches and trunk lid hinges with a light • Cover interior trim to prevent fading. • Keep all rubber parts free from oil and solvents. Engine • The engine oil and filter should be changed prior to storage, as used • Start the engine every 15 days. Run at fast idle until it reaches normal • With your foot on the brake, shift through all the gears while the

engine oil contains contaminates that may cause engine damage.

operating temperature.

engine is running.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

304

Vehicle Care

Fuel system • Fill the fuel tank with high-quality fuel until the first automatic shutoff

of the fuel pump nozzle.

Cooling system • Protect against freezing temperatures. • When removing vehicle from storage, check coolant fluid level. Confirm there are no cooling system leaks, and fluid is at the recommended level.

Battery • Check and recharge as necessary. Keep connections clean. • If storing your vehicle for more than 30 days without recharging the battery, it may be advisable to disconnect the battery cables to ensure battery charge is maintained for quick starting.

Note: If battery cables are disconnected, it will be necessary to reset memory features. Brakes • Make sure brakes and parking brake are fully released. Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle are • Move vehicles at least 25 feet (8 meters) every 15 days to lubricate

covered with grease to prevent rust.

working parts and prevent corrosion.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Vehicle Care

305

window surfaces.

during storage (mice/squirrel nests).

Removing Vehicle from Storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up on • Check windshield wipers for any deterioration. • Check under the hood for any foreign material that may have collected • Check the exhaust for any foreign material that may have collected • Check tire pressures and set tire inflation per the Tire Label. • Check brake pedal operation. Drive the vehicle 15 feet (4.5 meters) • Check fluid levels (including coolant, oil and gas) to make sure there • If the battery was removed, clean the battery cable ends and inspect. Contact your authorized dealer if you have any concerns or issues.

are no leaks and fluids are at recommended levels.

back and forth to remove rust build-up.

during storage.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

306

Wheels and Tires

GENERAL INFORMATION

Important Information for P265/40R22 Low-profile Tires and Wheels If your vehicle is equipped with P265/40R22 tires, they are low-profile tires. These tires and wheels are designed to give your vehicle a sport appearance. With low-profile tires, you may notice an increase in road noise and faster tire wear, depending on road conditions and driving styles. Due to their design, low-profile tires and wheels are more prone to road damage from potholes, rough or unpaved roads, car wash rails and curb contact than standard tires and wheels. Note: Your vehicle’s warranty does not cover these types of damage. Tires should always be kept at the correct inflation pressures and extra caution should be taken when operating on rough roads to avoid impacts that could cause wheel and tire damage.

Notice to Crossover Vehicle Owners

Crossover vehicles handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Crossover vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to

perform satisfactorily under off-road conditions.

WARNING: Crossover vehicles have a significantly higher rollover rate than other types of vehicles. To reduce the risk of

serious injury or death from a rollover or other crash you must: • Avoid sharp turns and abrupt maneuvers; • Drive at safe speeds for the conditions; • Keep tires properly inflated; • Never overload or improperly load your vehicle; and • Make sure every passenger is properly restrained.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Wheels and Tires

307

WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.

All occupants must wear seat belts. Children and infants must use appropriate restraints to minimize the risk of injury or ejection.

Study your owner’s manual for specific information about equipment features, instructions for safe driving and additional precautions to reduce the risk of an accident or serious injury.

All-Wheel Drive System (If Equipped)

WARNING: Do not become overconfident in the ability of all-wheel drive vehicles. Although an all-wheel drive vehicle

may accelerate better than a two-wheel drive vehicle in low-traction situations, it will not stop any faster than two-wheel drive vehicles. Always drive at a safe speed.

Note: Your all-wheel drive vehicle is not intended for off-road use. This feature gives your vehicle some limited off-road capabilities in which driving surfaces are relatively level, obstruction-free and otherwise similar to normal on-road driving conditions. Operating your vehicle under other than those conditions could subject the vehicle to excessive stress which might result in damage which is not covered under your warranty. With the all-wheel drive option, power will be delivered to the front wheels and distributed to the rear wheels as needed. This increases traction which may enable you to safely drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot. The system is active all the time and requires no input from the operator. For all-wheel drive vehicles, a spare tire of a different size other than the tire provided should never be used. A dissimilar spare tire size (other than the spare tire provided) or major dissimilar tire sized between the front and rear axles could cause the system to stop functioning and default to front-wheel drive.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

308

Wheels and Tires

How Your Vehicle Differs from Other Vehicles

Crossover vehicles can differ from some other vehicles in a few noticeable ways. Your vehicle may be: • Higher – to allow higher load • Shorter – to give it the capability

carrying capacity.

to approach inclines. All other things held equal, a shorter wheelbase may make your vehicle quicker to respond to steering inputs than a vehicle with a longer wheelbase. • Narrower – to provide greater maneuverability in tight spaces.

As a result of the above dimensional differences, crossover vehicles often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car.

TIRE CARE Information About Uniform Tire Quality Grading

Tire Quality Grades apply to new pneumatic passenger car tires. The Tire Quality Grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic passenger car tires. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, light truck or LT type tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2).

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Wheels and Tires

309

U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear 11⁄2 times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. Traction AA A B C

WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include

acceleration, cornering, hydroplaning or peak traction characteristics.

The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Temperature A B C

WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 139. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

310

Wheels and Tires

Glossary of Tire Terminology • Tire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry.

• Tire Identification Number (TIN): A number on the sidewall of

each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code.

• Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a maximum load at set pressure. For example: For P-metric tires 35 psi (2.4 bar) or 36 (2.5 bar) depending on tire size and for Metric tires 36 psi (2.5 bar). Increasing the inflation pressure beyond this pressure will not increase the tire capability.

• Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 42 psi (2.9 bar). Increasing the inflation pressure beyond this pressure will not increase the tire’s load-carrying capability.

• kPa: KiloPascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure. • Cold tire pressure: The tire pressure when the vehicle has been

stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.6 kilometers). • Recommended inflation pressure: The cold inflation pressure found

on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position) or Tire Label located on the B-Pillar or the edge of the driver’s door.

front door.

• B-pillar: The structural member at the side of the vehicle behind the • Bead area of the tire: Area of the tire next to the rim. • Sidewall of the tire: Area between the bead area and the tread. • Tread area of the tire: Area of the perimeter of the tire that • Rim: The metal support (wheel) for a tire or a tire and tube assembly

contacts the road when mounted on the vehicle.

upon which the tire beads are seated.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

Wheels and Tires

311

INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. Information on P Type Tires

P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.)

C D E

A. P: Indicates a tire, designated by the Tire and Rim Association, that may be used for service on cars, sport utility vehicles, minivans and light trucks. Note: If your tire size does not begin with a letter, this may mean it is designated by either the European Tire and Rim Technical Organization or the Japan Tire Manufacturing Association. B. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. C. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. D. R: Indicates a radial type tire. E. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter.

2014 Edge (edg) Owners Guide gf, 2nd Printing, March 2014
USA (fus)

312

Wheels and Tires

F. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in your owner’s manual. If not, contact a local tire dealer. Note: You may not find this information on all tires because it is not