2007 Ford E 250 Owners Manual

lifting the front of the child seat. Keeping the child seat just touching the vehicle seat gives the best protection in a severe crash. Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor. Try to tilt the child seat from side to side. Also try to tug the seat forward. Check to see if the anchors hold the seat in place.

If the safety seat is not anchored properly, the risk of a child being injured in a crash greatly increases.

103

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.

Utility vehicles have a significantly higher rollover rate than other types of vehicles. To reduce the risk of serious injury or

death from a rollover or other crash you must: • Avoid sharp turns and abrupt maneuvers; • Drive at safe speeds for the conditions; • Keep tires properly inflated; • Never overload or improperly load your vehicle; and • Make sure every passenger is properly restrained.

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. All occupants must

wear seat belts and children/infants must use appropriate restraints to minimize the risk of injury or ejection.

Study your Owner’s Guide and any supplements for specific information about equipment features, instructions for safe driving and additional precautions to reduce the risk of an accident or serious injury.

104

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

VEHICLE CHARACTERISTICS

How your vehicle differs from other vehicles SUV and trucks can differ from some other vehicles in a few noticeable ways. Your vehicle may be: • Higher – to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody components. • Shorter – to give it the capability

to approach inclines and drive over the crest of a hill without getting hung up or damaging underbody components. All other things held equal, a shorter wheelbase may make your vehicle quicker to respond to steering inputs than a vehicle with a longer wheelbase.

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use.

As a result of the above dimensional differences, SUV’s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car.

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

105

Tires, Wheels and Loading

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic tires for use on passenger cars. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.

Traction AA A B C The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

106

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include

acceleration, cornering, hydroplaning or peak traction characteristics.

Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed,

underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

TIRES Tires are designed to give many thousands of miles of service, but they must be maintained in order to get the maximum benefit from them.

Glossary of tire terminology • Tire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry.

• Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code.

• Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a maximum load at 35 psi [37 psi (2.5 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability.

• Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires].

107

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability.

• kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure. • Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.6 km).

front door.

• Recommended inflation pressure: The cold inflation pressure found on the Safety Compliance Certification Label or Tire Label located on the B-Pillar or the edge of the driver’s door. • B-pillar: The structural member at the side of the vehicle behind the • Bead area of the tire: Area of the tire next to the rim. • Sidewall of the tire: Area between the bead area and the tread. • Tread area of the tire: Area of the perimeter of the tire that • Rim: The metal support (wheel) for a tire or a tire and tube assembly

contacts the road when mounted on the vehicle.

upon which the tire beads are seated.

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. Remember that a tire can lose up to half of its air pressure without appearing flat. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company. Use a tire gauge to check the tire inflation pressure, including the spare (if equipped), at least monthly and before long trips. You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford Motor Company recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge. Use the recommended cold inflation pressure for optimum tire performance and wear. Under-inflation or over-inflation may cause uneven treadwear patterns.

108

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙blowout⬙,

with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents. A tire can lose up to half of its air pressure and not appear to be flat!

Always inflate your tires to the Ford recommended inflation pressure even if it is less than the maximum inflation pressure information found on the tire. The Ford recommended tire inflation pressure is found on the Safety Compliance Certification Label or Tire Label which is located on the B-Pillar or the edge of the driver’s door. Failure to follow the tire pressure recommendations can cause uneven treadwear patterns and adversely affect the way your vehicle handles. Maximum Permissible Inflation Pressure is the tire manufacturer’s maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or Tire Label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or Tire Label. When weather temperature changes occur, tire inflation pressures also change. A 10° F (6° C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recommended cold pressures. A hot tire at or below recommended cold inflation pressure could be significantly under-inflated.

109

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure with the tire gauge. 3. Add enough air to reach the recommended air pressure. Note: If you overfill the tire, release air by pushing on the metal stem in the center of the valve. Then recheck the pressure with your tire gauge. 4. Replace the valve cap. 5. Repeat this procedure for each tire, including the spare. Note: Some spare tires operate at a higher inflation pressure than the other tires. For T-type/mini-spare tires (see T-Type/Mini-Spare Tire Information section for description): Store and maintain at 60 psi (4.15
bar). For Full Size and Dissimilar spare tires (see Dissimilar Spare Tire/Wheel Information section for description): Store and maintain at the higher of the front and rear inflation pressure as shown on the Safety Compliance Certification Label or the Tire Label. 6. Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak. 7. Check the sidewalls to make sure there are no gouges, cuts or bulges.

110

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Tire inflation information All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, they cannot be treated like normal light truck tires. Tire service, including adjusting tire pressure, must be performed by personnel trained, supervised and equipped according to Federal Occupational Safety and Health Administration (OSHA) regulations. For example, during any procedure involving tire inflation, the technician or individual must utilize a remote inflation device, and ensure that all persons are clear of the trajectory area.

WARNING An inflated tire and rim can be very dangerous if improperly used, serviced or maintained. To reduce the risk of

serious injury, never attempt to re-inflate a tire which has been run flat or seriously under-inflated without first removing the tire from the wheel assembly for inspection. Do not attempt to add air to tires or replace tires or wheels without first taking precautions to protect persons and property.

111

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Stay out of the trajectory (1) as indicated in the illustration.

TIRE CARE

Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety, tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail. Improper or inadequate vehicle maintenance can cause tires to wear abnormally. Inspect all your tires, including the spare, frequently, and replace them if one or more of the following conditions exist:

112

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or “wear bars”, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to 1/16th of an inch (2 mm). When the tire tread wears down to the same height as these “wear bars”, the tire is worn out and must be replaced.

Damage Periodically inspect the tire treads and sidewalls for damage (such as bulges in the tread or sidewalls, cracks in the tread groove and separation in the tread or sidewall). If damage is observed or suspected have the tire inspected by a tire professional. Tires can be damaged during off-road use, so inspection after off-road use is also recommended.

Age Tires degrade over time depending on many factors such as

weather, storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear. However, heat caused by hot climates or frequent high loading conditions can accelerate the aging process and may require tires to be replaced more frequently. You should replace your spare tire when you replace the road tires or after six years due to aging even if it has not been used.

113

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall.

Tire Replacement Requirements Your vehicle is equipped with tires designed to provide a safe ride and handling capability.

Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus

LT-metric or all-season versus all-terrain) as those originally provided by Ford. The recommended tire and wheel size may be found on either the Safety Compliance Certification Label or the Tire Label which is located on the B-Pillar or edge of the driver’s door. If this information is not found on these labels then you should consult your Ford Dealer. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Additionally the use of non-recommended tires and wheels could cause steering, suspension, axle or transfer case/power transfer unit failure. If you have questions regarding tire replacement, see an authorized dealer.

114

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the

tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi greater than the maximum pressure on the tire sidewall, the following precautions must be taken to protect the person mounting the tire: 1. Make sure that you have the correct tire and wheel size. 2. Lubricate the tire bead and wheel bead seat area again. 3. Stand at a minimum of 12 feet away from the tire wheel assembly. 4. Use both eye and ear protection. For a mounting pressure more than 20 psi greater than the maximum pressure, a Ford Dealer or other tire service professional should do the mounting. Always inflate steel carcass tires with a remote air fill with the person inflating standing at a minimum of 12 ft. away from the tire wheel assembly.

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. It is recommended that the two front tires or two rear tires generally be replaced as a pair.

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking

If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an

explosion. A tire can explode in as little as three to five seconds.

Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander.

115

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Highway hazards No matter how carefully you drive there’s always the possibility that you may eventually have a flat tire on the highway. Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect your tire or vehicle has been damaged, immediately reduce your speed. Drive with caution until you can safely pull off the road. Stop and inspect the tires for damage. If a tire is under-inflated or damaged, deflate it, remove wheel and replace it with your spare tire and wheel. If you cannot detect a cause, have the vehicle towed to the nearest repair facility or tire dealer to have the vehicle inspected.

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically. Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer. Front wheel drive (FWD) vehicles and those with an independent rear suspension (if equipped) may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear.

Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly, providing better tire performance and longer tire life. Unless otherwise specified, rotate the tires approximately every 5,000 miles (8,000 km).

116

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (AWD) vehicles (front tires at top of diagram)

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare tire/wheel it is intended for temporary use only and should not be used in a tire rotation. Note: After having your tires rotated, inflation pressure must be checked and adjusted to the vehicle requirements.

117

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading • DRW – Six tire rotation If your vehicle is equipped with dual rear wheels it is recommended that the front and rear tires (in pairs) be rotated only side to side. We do not recommend splitting up the dual rear wheels. Rotate them side to side as a set/pair. After tire rotation, inflation pressures must be adjusted for the tires new positions in accordance with vehicle requirements.

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask your authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare tire/wheel it is intended for temporary use only and should not be used in a tire rotation. Note: After having your tires rotated, inflation pressure must be checked and adjusted to the vehicle requirements.

INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall.

118

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the Tire and Rim Association (T&RA), that may be used for service on cars, SUVs, minivans and light trucks. Note: If your tire size does not begin with a letter this may mean it is designated by either ETRTO (European Tire and Rim Technical Organization) or JATMA (Japan Tire Manufacturing Association). 2. 215: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. 3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter. 6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in your Owner’s Guide. If not, contact a local tire dealer. Note: You may not find this information on all tires because it is not required by federal law. 7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for the difference in conditions. The ratings range from 81 mph (130 km/h) to 186 mph (299 km/h). These ratings are listed in the following chart.

119

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Note: You may not find this information on all tires because it is not required by federal law.

Letter rating

Speed rating - mph (km/h)

81 mph (130 km/h) 87 mph (140 km/h) 99 mph (159 km/h) 106 mph (171 km/h) 112 mph (180 km/h) 118 mph (190 km/h) 124 mph (200 km/h) 130 mph (210 km/h) 149 mph (240 km/h) 168 mph (270 km/h) 186 mph (299 km/h)

Note: For tires with a maximum speed capability over 149 mph (240
km/h), tire manufacturers sometimes use the letters ZR. For those with a maximum speed capability over 186 mph (299 km/h), tire manufacturers always use the letters ZR. 8. U.S. DOT Tire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall. 9. M+S or M/S: Mud and Snow, or AT: All Terrain, or AS: All Season. 10. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. 11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the Safety Compliance Certification Label, which is located on the B-Pillar or the edge of the driver’s door, for the correct tire pressure for your vehicle.

120

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the

wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150
would wear one and one-half (11⁄2) times as well on the government course as a tire graded 100. • Traction: The traction grades, from highest to lowest are AA, A, B,

and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

• Temperature: The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or Tire Label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the vehicle label. The tire suppliers may have additional markings, notes or warnings such as standard load, radial tubeless, etc.

121

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/Load Inflation Limits: Indicates the tire’s load-carrying capabilities and its inflation limits. 3. Maximum Load Dual lb. (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a dual; defined as four tires on the rear axle (a total of six or more tires on the vehicle). 4. Maximum Load Single lb. (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a single; defined as two tires (total) on the rear axle.

122

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. 2. 145: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire. 3. 80: Indicates the aspect ratio which gives the tire’s ratio of height to width. Numbers of 70 or lower indicate a short sidewall. 4. D: Indicates a “diagonal” type tire. R: Indicates a “radial” type tire. 5. 16: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter.

Location of the tire label You will find a Tire Label containing tire inflation pressure by tire size and other important information located on the B-Pillar or the edge of the driver’s door. Refer to the payload description and graphic in the Vehicle loading — with and without a trailer section.

123

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

SNOW TIRES AND CHAINS

Snow tires must be the same size and grade as the tires you currently have on your vehicle.

The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same size and specifications) be used, as chains may chip aluminum wheels. Follow these guidelines when using snow tires and chains: • Use only SAE Class S chains. • Install chains securely, verifying that the chains do not touch any • Drive cautiously. If you hear the chains rub or bang against your

wiring, brake lines or fuel lines.

vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent damage to your vehicle.

• If possible, avoid fully loading your vehicle. • Remove the tire chains when they are no longer needed. Do not use • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.

tire chains on dry roads.

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer, to keep your loaded vehicle weight within its design rating capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle’s weight ratings, with or without a trailer, from the vehicle’s Tire Label or Safety Compliance Certification Label: Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, or optional equipment.

124

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment.

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label). Look for “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for maximum payload. The payload listed on the Tire Label is the maximum payload for the vehicle as built by the assembly plant. If any aftermarket or authorized-dealer installed equipment has been installed on the vehicle, the weight of the equipment must be subtracted from the payload listed on the Tire Label in order to determine the new payload.

The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available. Overloading or improperly loading your vehicle can contribute to loss of vehicle control and vehicle rollover.

125

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Example only:

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.

126

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR. Note: For trailer towing information refer to Trailer towing found in this chapter or the RV and Trailer Towing Guide provided by your authorized dealer.

GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo + passengers. GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The GVW must never exceed the GVWR.

Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury.

127

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing vehicle’s braking system is rated for operation at GVWR, not at GCWR.) Separate functional brakes should be used for safe control of towed vehicles and for trailers where the GCW of the towing vehicle plus the trailer exceed the GVWR of the towing vehicle. The GCW must never exceed the GCWR. Maximum Loaded Trailer Weight – is the highest possible weight of a fully loaded trailer the vehicle can tow. It assumes a vehicle with only mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer) for more detailed information. Tongue Load or Fifth Wheel King Pin Weight – refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5,000 lb. (2,268 kg) conventional trailer, multiply 5,000
by 0.10 and 0.15 to obtain a proper tongue load range of 500 to 750 lb. (227 to 340 kg). For an 11,500 lb. (5,216 kg) fifth wheel trailer, multiply by 0.15 and 0.25 to obtain a proper king pin load range of 1,725 to 2,875
lb. (782 to 1,304 kg)

Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label.

Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s

GVWR and GAWR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GAWR limitations.

128

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury.

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1,400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400-750 (5 x 150) = 650 lb.). In metric units (635-340 (5 x 68) = 295 kg.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity: • Another example for your vehicle with 1400 lb. (635 kg) of cargo and luggage capacity. You decide to go golfing. Is there enough load capacity to carry you, 4 of your friends and all the golf bags? You and four friends average 220 lb. (99 kg) each and the golf bags weigh approximately 30 lb. (13.5 kg) each. The calculation would be: 1400 - (5 x 220) - (5 x 30) = 1400 - 1100 - 150 = 150 lb. Yes, you have enough load capacity in your vehicle to transport four friends and your golf bags. In metric units, the calculation would be: 635 kg - (5 x 99 kg) - (5 x 13.5 kg) = 635 - 495 - 67.5 = 72.5 kg.

• A final example for your vehicle with 1400 lb. (635 kg) of cargo and luggage capacity. You and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100
lb. (45 kg) bags of cement. Do you have enough load capacity to

129

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 - 540 = -103 kg. You will need to reduce the load weight by at least 240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, then the load calculation would be: 1400 - (2 x 220) - (9 x 100) = 1400 - 440 - 900 = 60 lb. Now you have the load capacity to transport the cement and your friend home. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (9 x 45 kg) = 635 - 198 - 405 = 32 kg.

The above calculations also assume that the loads are positioned in your vehicle in a manner that does not overload the Front or the Rear Gross Axle Weight Rating specified for your vehicle on the Safety Compliance Certification Label found on the edge of the driver’s door.

Special loading instructions for owners of pickup trucks and utility-type vehicles

For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in

the Driving chapter of this Owner’s Guide.

Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping

distance, should be taken when driving a heavily loaded vehicle.

Your vehicle can haul more cargo and people than most passenger cars. Depending upon the type and placement of the load, hauling cargo and people may raise the center of gravity of the vehicle.

TRAILER TOWING Refer to 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for Diesel engine towing information. Your vehicle may tow a class I, II or III trailer, provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio on the following charts.

130

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GCWR (Gross Combined Weight Rating)/Trailer Weights

Engine

Rear axle ratio

Maximum GCWR - lb.

(kg)

Maximum

Loaded

Trailer Weight

- lb. (kg)

Maximum

frontal area of

trailer - ft2

(m2)

4.6L

4.6L

4.6L

4.6L

E-150 Regular/RV Van (8520 GVWR)

3.73

4.10

11500
(5216) 12000
(5443)

6000 (2722)

60 (5.52)

6500 (2948)

60 (5.52)

E-150 Van (Crew) (8520 GVWR)

3.73

4.10

11500
(5216) 12000
(5443)

5900 (2676)

60 (5.52)

6400 (2903)

60 (5.52)

E-150 Regular Wagon (7–passenger) (8520 GVWR)

4.6L

4.10

12000
(5443)

5900 (2676)

60 (5.52)

E-150 Regular Wagon (8–passenger) (8520 GVWR)

4.6L

4.10

12000
(5443)

6200 (2812)

60 (5.52)

E-150 Regular/RV Van (8600 GVWR)

5.4L

5.4L

5.4L

5.4L

3.55

3.73

12000
(5443) 13000
(5897)

6500 (2948)

60 (5.52)

7500 (3402)

60 (5.52)

E-150 Van (Crew) (8600 GVWR)

3.55

3.73

12000
(5443) 13000
(5897)

6300 (2858)

60 (5.52)

7300 (3311)

60 (5.52)

131

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GCWR (Gross Combined Weight Rating)/Trailer Weights

Engine

Rear axle ratio

Maximum GCWR - lb.

(kg)

Maximum

Loaded

Trailer Weight

- lb. (kg)

Maximum

frontal area of

trailer - ft2

(m2)

E-150 Regular Wagon (7–passenger) (8600 GVWR)

3.55

3.73

12000
(5443) 13000
(5897)

5900 (2676)

60 (5.52)

6900 (3130)

60 (5.52)

E-150 Regular Wagon (8–passenger) (8600 GVWR)

3.55

3.73

12000
(5443) 13000
(5897)

6100 (2767)

60 (5.52)

7100 (3221)

60 (5.52)

E-250 Regular/RV Van (8900 GVWR)

3.73

4.10

11500
(5216) 12000
(5443)

6100 (2767)

60 (5.52)

6600 (2994)

60 (5.52)

E-250 Regular Van (Crew) (8900 GVWR)

3.73

4.10

11500
(5216) 12000
(5443)

5900 (2676)

60 (5.52)

6400 (2903)

60 (5.52)

E-250 Extended/RV Van (8900 GVWR)

3.73

4.10

11500
(5216) 12000
(5443)

5900 (2676)

60 (5.52)

6400 (2903)

60 (5.52)

5.4L

5.4L

5.4L

5.4L

4.6L

4.6L

4.6L

4.6L

4.6L

4.6L

132

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GCWR (Gross Combined Weight Rating)/Trailer Weights

Engine

Rear axle ratio

Maximum GCWR - lb.

(kg)

Maximum

Loaded

Trailer Weight

- lb. (kg)

Maximum

frontal area of

trailer - ft2

(m2)

E-250 Extended Van (Crew) (8900 GVWR)

4.6L

4.6L

3.73

4.10

11500
(5216) 12000
(5443)

5700 (2585)

60 (5.52)

6200 (2812)

60 (5.52)

E-250 Regular/RV Van (9000 GVWR)

5.4L

3.73

13000
(5896)

7500 (3402)

60 (5.52)

E-250 Regular Van (Crew) (9000 GVWR)

5.4L

3.73

13000
(5896)

7300 (3311)

60 (5.52)

E-250 Extended/RV Van (9000 GVWR)

5.4L

3.73

13000
(5896)

7400 (3357)

60 (5.52)

E-250 Extended Van (Crew) (9000 GVWR)

5.4L

3.73

13000
(5896)

7200 (3266)

60 (5.52)

E-250 Cutaway (8600 GVWR)

4.6L

4.10

12000
(5443)

7500 (3402)

60 (5.52)

E-350 Regular/RV Van (9500 GVWR)

5.4L

5.4L

6.8L

6.8L

3.73

4.10

3.73

4.10

13000
(5897) 13000
(5897) 15000
(6804) 18500
(8391)

7500 (3402)

60 (5.52)

7500 (3402)

60 (5.52)

9200 (4173)

60 (5.52)

10000 (4536)

60 (5.52)

133

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GCWR (Gross Combined Weight Rating)/Trailer Weights

Engine

Rear axle ratio

Maximum GCWR - lb.

(kg)

Maximum

Loaded

Trailer Weight

- lb. (kg)

Maximum

frontal area of

trailer - ft2

(m2)

E-350 Regular Van (Crew) (9500 GVWR)

3.73

4.10

3.73

4.10

13000
(5897) 13000
(5897) 15000
(6804) 18500
(8391)

7300 (3311)

60 (5.52)

7300 (3311)

60 (5.52)

9000 (4082)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Extended/RV Van (9400 GVWR)

3.73

4.10

3.73

4.10

13000
(5897) 13000
(5897) 15000
(6804) 18500
(8391)

7300 (3311)

60 (5.52)

7300 (3311)

60 (5.52)

9100 (4128)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Extended Van (Crew) (9400 GVWR)

3.73

4.10

3.73

4.10

13000
(5897) 13000
(5897) 15000
(6804) 18500
(8391)

7100 (3221)

60 (5.52)

7100 (3221)

60 (5.52)

8900 (4037)

60 (5.52)

10000 (4536)

60 (5.52)

5.4L

5.4L

6.8L

6.8L

5.4L

5.4L

6.8L

6.8L

5.4L

5.4L

6.8L

6.8L

134

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GCWR (Gross Combined Weight Rating)/Trailer Weights

Engine

Rear axle ratio

Maximum GCWR - lb.

(kg)

Maximum

Loaded

Trailer Weight

Maximum

frontal area of

trailer - ft2

(m2) E-350 Regular Wagon (11/12–passenger) (8600 GVWR)

- lb. (kg)

5.4L

3.73

13000
(5897)

6900 (3130)

60 (5.52)

E-350 Extended Wagon (12–passenger) (9300 GVWR)

5.4L

3.73

13000
(5897)

6700 (3039)

60 (5.52)

E-350 Extended Wagon (14/15–passenger) (9100 GVWR)

5.4L

3.73

13000
(5897)

6600 (2994)

60 (5.52)

E-350 Cutaway (138” wheelbase, single rear wheel) (9600

GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

8100 (3674)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Cutaway (138” wheelbase, dual rear wheel) (10000

GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

7900 (3583)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Cutaway (158” wheelbase, dual rear wheel) (10000

GVWR)

5.4L

4.10

13000
(5897)

7900 (3583)

60 (5.52)

135

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GCWR (Gross Combined Weight Rating)/Trailer Weights

Engine

Rear axle ratio

Maximum GCWR - lb.

(kg)

Maximum

Loaded

Trailer Weight

- lb. (kg)

Maximum

frontal area of

trailer - ft2

(m2)

E-350 Cutaway (138” wheelbase, dual rear wheel) (10700

GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

7900 (3583)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Cutaway (158” wheelbase, dual rear wheel) (11500

GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

7900 (3583)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Cutaway (176” wheelbase, dual rear wheel) (11500

GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

7900 (3583)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Stripped Chassis (138” wheelbase, single rear wheel)

(9600 GVWR)

5.4L

5.4L

3.73

4.10

13000
(5897) 13000
(5897)

8800 (3992)

8800 (3992)

8800 (3992)

8800 (3992)

E-350 Stripped Chassis (158” wheelbase, single rear wheel)

(9600 GVWR)

5.4L

5.4L

3.73

4.10

13000
(5897) 13000
(5897)

8700 (3946)

60 (5.52)

8700 (3946)

60 (5.52)

136

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GCWR (Gross Combined Weight Rating)/Trailer Weights

Engine

Rear axle ratio

Maximum GCWR - lb.

(kg)

Maximum

Loaded

Trailer Weight

- lb. (kg)

Maximum

frontal area of

trailer - ft2

(m2)

E-350 Stripped Chassis (138” wheelbase, dual rear wheel)

(10000 GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

8500 (3856)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Stripped Chassis (138” wheelbase, dual rear wheel)

(10000 GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

8500 (3856)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Stripped Chassis (158” wheelbase, dual rear wheel)

(10000 GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

8400 (3810)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Stripped Chassis (158” wheelbase, dual rear wheel)

(11000 GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

8400 (3810)

60 (5.52)

10000 (4536)

60 (5.52)

E-350 Stripped Chassis (176” wheelbase, dual rear wheel)

(10000 GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

8400 (3810)

60 (5.52)

10000 (4536)

60 (5.52)

137

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GCWR (Gross Combined Weight Rating)/Trailer Weights

Engine

Rear axle ratio

Maximum GCWR - lb.

(kg)

Maximum

Loaded

Trailer Weight

- lb. (kg)

Maximum

frontal area of

trailer - ft2

(m2)

E-350 Stripped Chassis (176” wheelbase, dual rear wheel)

(11000 GVWR)

5.4L

6.8L

4.10

4.10

13000
(5897) 18500
(8391)

8400 (3810)

60 (5.52)

10000 (4536)

60 (5.52)

E-450 Cutaway (158” wheelbase, dual rear wheel) (14050

GVWR)

6.8L

4.56

20000
(9072)

10000 (4536)

60 (5.52)

E-450 Cutaway (176” wheelbase, dual rear wheel) (14050

GVWR)

6.8L

4.56

20000
(9072)

10000 (4536)

60 (5.52)

E-450 Stripped Chassis (158” wheelbase, dual rear wheel)

(14050 GVWR)

5.4L

6.8L

4.56

4.56

14050
(6373) 20000
(9072)

9200 (4173)

60 (5.52)

10000 (4536)

60 (5.52)

E-450 Stripped Chassis (176” wheelbase, dual rear wheel)

(14050 GVWR)

5.4L

6.8L

4.56

4.56

14050
(6372) 20000
(9072)

9200 (4173)

60 (5.52)

10000 (4536)

60 (5.52)

138

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

GCWR (Gross Combined Weight Rating)/Trailer Weights

Engine

Rear axle ratio

Maximum GCWR - lb.

(kg)

Maximum

Loaded

Trailer Weight

- lb. (kg)

Maximum

frontal area of

trailer - ft2

(m2)

Maximum trailer weight for all cutaway (E-350 and E-450) vehicles must be calculated by subtracting the weight of the vehicle (including incomplete vehicle weight and payload which includes second unit body weight, cargo and passengers) from the GCW. Otherwise, maximum trailer weight is 10,000 lb. (4536 kg). For high altitude operation reduce GCWR by 2% per 1,000 ft. (300
meters) elevation. To determine the maximum trailer weight designed for your particular vehicle as equipped, follow the section Vehicle loading earlier in this chapter. Your vehicle’s load capacity is designated by weight, not by volume, so you cannot necessarily use all available space when loading a vehicle. Distribute the load so that only 10–15% of the total is on the tongue. Tie down the load so that it does not shift and change the weight on the hitch. Towing a trailer places an additional load on your vehicle’s engine, transmission, axle, brakes, tires and suspension. Inspect these components carefully after any towing operation. Note: Do not exceed the GVWR or the GAWR specified on the certification label.

Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in

engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury.

Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. See your authorized dealer or a reliable trailer dealer if you require assistance. Hitches Do not use or install hitches that clamp onto the bumper or to the axle. Underbody hitches are acceptable if installed properly.

139

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

Tires, Wheels and Loading

Safety chains Always connect the trailer’s safety chains to the frame or hook retainers of the vehicle hitch. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper.

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations.

Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough

braking power and your chances of having a collision greatly increase.

The braking system of the tow vehicle is rated for operation at the GVWR not GCWR.

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. See your authorized dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps.

Using a step bumper (if equipped) The rear bumper is equipped with an integral hitch and only requires a ball with a one inch (25.4 mm) shank diameter. The bumper has a 5,000
lb. (2,270 kg) trailer weight and 500 lb. (227 kg) tongue weight capacity. If it is necessary to relocate the trailer hitch ball position, a frame-mounted trailer hitch must be installed.

Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (112 km/h) during the first 500 miles (800 km) of towing a trailer, and don’t make full throttle starts.

• Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades.

140

2007 Econoline (eco) Owners Guide (post-2002-fmt) USA (fus)

in transmission cooling.

Tires, Wheels and Loading • Consult your local motor vehicle speed regulations for towing a trailer.