Download PDF Manual

Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2. Repeat the words and phrases when prompted by Uconnect™ Voice. For best results, the “Voice Training” session should be completed when the vehicle is parked, engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135


SEATS Seats are a part of the Occupant Restraint System of the vehicle.


WARNING!


• It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and


using a seat belt properly.


136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Power Seat — If Equipped Some models may be equipped with a six-way power driver seat. The power seat switch is located on the outboard side of the front seat cushion. Use this switch to move the seat up or down, forward or rearward or to tilt the seat.


Power Seat Switch


Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when you have reached the desired position. Tilting The Seat Up Or Down The angle of the seat cushion can be adjusted in four directions. Pull upward or push downward on the front or rear of the seat switch, the front or rear of the seat cushion will move in the direction of the switch. Release the switch when you have reached the desired position.


WARNING!


• Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137


CAUTION!


Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.


Heated Seats — If Equipped On some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. There are two heated seat switches that allow the driver and passenger to operate the seats independently. The controls for each seat are located on a switch bank near the bottom center of the instrument panel.


138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can choose from HIGH, LOW or OFF heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for HIGH, one for LOW and none for OFF.


Press the switch once to select HIGH-level heating. Press the switch a second time to select LOW-level heating. Press the switch a third time to shut the heating elements OFF.


When the HIGH-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal HIGH-level. If the HIGH-level setting is selected, the system will automatically switch to LOW-level after approximately 30 minutes of continuous operation. At that time, the number of illuminated LEDs changes from two to one, indicating the change. The LOW-level setting will turn OFF automatically after approximately 30 min- utes.


NOTE: Once a heat setting is selected, heat will be felt within two to five minutes.


WARNING!


• Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.


Front Manual Seat Adjustment For models equipped with manual seats, the driver and passenger seats can be adjusted forward or rearward by using a bar by the front of the seat cushion, near the floor.


Manual Seat Adjustment


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139
While sitting in the seat, lift up on the bar located and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.


WARNING!


• Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.


140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat — Manual Recline To recline the seatback, lift the recline lever, located on the outboard side of the seat, lean back and release the lever when you reach the desired position.


WARNING!


Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.


Fold-Flat Front Passenger Seat The front passenger seatback can be folded flat to allow for extended cargo space. Pull up on the lever to fold down the seatback.


Seatback Release Lever


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141


WARNING!


The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision.


Active Head Restraints — Front Seats Active Head Restraints are passive, deployable compo- nents, and vehicles with this equipment cannot be readily identified by any markings, only through visual inspec- tion of the head restraint. The head restraint will be split in two halves, with the front half being soft foam and trim, the back half being decorative plastic.


Fold Flat Passenger Seat


Head Restraints Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.


142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts. Refer to “Occupant Re- straints” in “Things To Know Before Starting Your Ve- hicle” for further information. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint.


Push Button


For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143


Active Head Restraint (Normal Position)


Active Head Restraint (Tilted)


NOTE: • The head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer.


144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


• In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things To Know Before Starting Your Vehicle” for further information.


WARNING!


• Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players. These items may interfere with the operation of the Active Head Restraint in the event of a collision and could result in serious injury or death.


(Continued)


WARNING! (Continued)


• Active Head Restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the Ac- tive Head Restraint ensure that all cargo is se- cured, as loose cargo could contact the Active Head Restraint during sudden stops. Failure to follow this warning could cause personal injury if the Active Head Restraint is deployed.


Static Head Restraints — Rear Seats The two outboard seats are equipped with adjustable head restraints. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the adjustment button, located on the base of the head restraint, and push downward on the head restraint.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145


• Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for information on tether routing.


WARNING!


Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should be checked prior to operating the vehicle and never adjusted while the vehicle is in motion.


Adjustment Button


NOTE: • The head restraints should only be removed by quali- fied technicians, for service purposes only. If either of the head restraints require removal, see your autho- rized dealer.


146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 60/40 Split Folding Rear Seat with Fold-Flat Feature To provide additional storage area, each rear seat can be folded flat to allow for extended cargo space and still maintain some rear seating room.


WARNING!


Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.


reposition the front seat to its mid-track position.


NOTE: • Prior to folding the rear seat, it may be necessary to • Be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily.


Rear Seat Release Strap


WARNING!


• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and


using a seat belt properly.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147


To Lower Rear Seat 1. Locate the release strap on the lower outboard side of each rear seatback. 2. Pull the release strap (toward the front of the vehicle).


Rear Seat Release Strap


3. Fold the rear seat completely forward. 4. Push down on the seatback to lock it in the folded position.


148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise Rear Seat If locked in the folded position, pull the release strap (toward the front of the vehicle). Raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position.


WARNING!


Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.


Recliner Adjustment The rear seatback also reclines for additional passenger comfort. Pull the release strap while sitting in the rear seat to recline the seatback.


Rear Seatback Release Strap


WARNING!


Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death.


TO OPEN AND CLOSE THE HOOD To open the hood, there are two latches that must be released. 1. Pull the hood release lever located under the left side of the instrument panel.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149


Hood Release Lever


150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Push the safety latch lever to the right. It is located between the grille and hood opening left of the center.


Safety Latch


CAUTION!


To prevent possible damage:


(Continued)


CAUTION! (Continued)


• Do not slam the hood to close it. • Lower the hood to approximately 6 in (15.2 cm) above the closed position and drop the hood to latch it. • Never drive your vehicle unless the hood is fully


closed, with both latches engaged.


NOTE: Ensure hood prop rod is fully seated into clip before closing hood to prevent damage to grille.


WARNING!


Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.


LIGHTS Multifunction Lever The multifunction lever controls the operation of the parking lights, headlights, headlight beam selection, passing light, fog lights, instrument panel light dimming and turn signals. The multifunction lever is located on the left side of the steering column.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151


Headlights and Parking Lights Turn the end of the multifunction lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation.


Multifunction Lever


Headlight Switch


152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, rotate the center portion of the multifunction lever up or down. If the driver’s door is left open, and the head- NOTE: lights or parking lights are left on, a chime will sound. Daytime Running Lights — If Equipped The high beam headlights will turn on as Daytime Running Lights (DRL) and operate at lower intensity whenever the ignition is ON, the engine is running, the headlight switch is off, the parking brake is released and the shift lever is in any position except PARK. NOTE: The Daytime Running Lights will turn off automatically when a turn signal is in operation and turn on again when the turn signal is not operating.


Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beams. Pull the lever toward you to switch the headlights back to low beams. Flash-to-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer- ing wheel. This will turn on the high beam headlights until the lever is released. Front Fog Lights — If Equipped


The front fog light switch is in the multifunction lever. To activate the front fog lights, turn on the parking or low beam headlights and pull out the


end of the lever.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153


Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.


Fog Light Operation


NOTE: The fog lights will only operate with the parking lights or the headlights on low beam. Selecting high beam headlights will turn off the fog lights.


Turn Signal Operation


154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. • A tone will chime if the turn signals are left on for


more than 1 mile (2 km).


Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off.


Instrument Panel Dimmer Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on. Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are on. Rotate the center portion of the lever upward to the last detent to turn on the interior lighting.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155


Interior Lights The overhead light comes on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the multifunction lever fully upward. The overhead light will automatically turn off in approxi- mately 10 minutes if a door is left open or the dimmer control is left in the dome light position and the key is not in the ignition. Turn the ignition switch ON to restore the overhead light operation. Daytime Brightness Feature Certain instrument panel components (odometer, radio display) can be illuminated at full brightness during the daytime. This can be helpful when driving with your headlights on during the daytime, such as in a parade or a funeral procession. To activate this feature, rotate the left stalk one detent lower than the dome light.


Dimmer Control


156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located at the end of the lever. For information on using the rear window wiper/ washer, refer to “Rear Window Features” in “Under- standing the Features of Your Vehicle”.


Windshield Wiper Operation Rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper opera- tion.


Wiper/Washer Lever


Front Wiper Control


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157


CAUTION! (Continued)


• Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.


NOTE: The wipers will automatically return to the “park” position if you turn OFF the ignition switch while they are operating. The wipers will resume operation when you turn the ignition switch back to the ON position.


CAUTION!


• Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • In cold weather, always turn off the wiper switch and allow the wipers to return to the “Park” position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.


(Continued)


158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Use the intermittent wiper system when weather condi- tions make a single wiping cycle with a variable pause between cycles desirable. Rotate the end of the wind- shield wiper/washer control lever to the first detent, and then turn the end of the lever to select the desired delay interval.


Front Wiper Control


There are five delay settings, which allow you to regulate the wipe interval from a minimum of one cycle every second to a maximum of approximately 36 seconds between cycles or from a minimum of one cycle every second to a maximum of approximately 18 seconds between cycles at vehicle speeds greater than 10 mph (16 km/h). NOTE: The wiper delay times depend on vehicle speed. If the vehicle is moving less than 10 mph (16 km/h), delay times will be doubled. Windshield Washers To use the washer, pull the windshield wiper/washer control lever toward you and hold it for as long as washer spray is desired (for a maximum of 10 seconds). If you activate the washer while the wiper control is in the delay range, the wipers will operate in low-speed for two or three wipe cycles after releasing the lever and then resume the intermittent interval previously selected.


If you activate the washer while the wiper control is in the off position, the wipers will operate for two or three wipe cycles and then turn off.


WARNING!


Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.


Mist Feature Push downward on the windshield wiper/washer con- trol lever to activate a single wipe cycle to clear the windshield of road mist or spray from a passing vehicle. The wipers will continue to operate until you release the lever.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159


Mist Control


TILT STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the turn signal lever.


160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Push the lever down to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Pull the lever up to lock the column firmly in place.


Tilt Steering Control Handle


WARNING!


Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this warning may result in serious injury or death.


ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The Electronic Speed Control lever is located on the right side of the steering wheel.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161
System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate. To turn the system off, push the ON/OFF button a second time. The CRUISE indicator will turn off. The system should be turned off when not in use.


WARNING!


Electronic Speed Control Lever


In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control


Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it.


162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set A Desired Speed Turn the Electronic Speed Control ON. When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever. To Deactivate A soft tap on the brake pedal, pulling the Electronic Speed Control lever toward you, “CANCEL”, or normal brake or clutch pressure while slowing the vehicle will deactivate speed control without erasing the set speed memory. Pressing the ON/OFF button or turning off the ignition switch erases the set speed memory. To Resume Speed To resume a previously set speed, push the RESUME ACCEL lever up and release. Resume can be used at any speed above 25 mph (40 km/h).


To Vary The Speed Setting When the Electronic Speed Control is set, you can in- crease speed by pushing up and holding the RESUME ACCEL lever. If the lever is continually held in the RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. Tapping the RESUME ACCEL lever once will result in a 1 mph (2 km/h) increase in set speed. Each subsequent tap of the lever results in an increase of 1 mph (2 km/h). To decrease speed while the Electronic Speed Control is set, push down and hold the SET DECEL lever. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and the new set speed will be established.


Tapping the SET DECEL lever once will result in a 1 mph (2 km/h) decrease in set speed. Each subsequent tap of the lever results in a decrease of 1 mph (2 km/h). To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without Electronic Speed Control.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163


WARNING!


Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.


PARKSENSE姞 REAR PARK ASSIST — IF EQUIPPED ParkSense威 Rear Park Assist is a driver aid that senses for obstacles behind the vehicle and provides both visible and audible warnings to indicate the range of the object. System Usage Precautions NOTE: • Ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep ParkSense威 operating properly.


164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


affect the performance of ParkSense威.


• Jackhammers, large trucks, and other vibrations could • When you turn ParkSense威 off, the instrument cluster will display “PARK ASSIST DISABLED.” Further- more, once you turn ParkSense威 off, it remains off until you turn it on again, even if you cycle the ignition key. • When you move the shift lever to the REVERSE position and ParkSense威 is turned off, a single chime will sound once per ignition cycle and the instrument cluster will display “PARK ASSIST DISABLED.” • ParkSense威, when on, will MUTE the radio when it is • If a ParkSense威 system malfunction occurs, a single chime will sound once per ignition cycle. In addition, the Electronic Vehicle Information Center (EVIC) will display “SERVICE PARK ASSIST SYSTEM” and the


sounding a tone.


LED in the ParkSense威 Rear Park Assist switch will illuminate. If this occurs after making sure the rear bumper is free of snow, ice, mud, dirt and debris, see your authorized dealer for service.


CAUTION!


• ParkSense威 is only a parking aid and it is unable to recognize every obstacle, including small ob- stacles. Parking curbs might be temporarily de- tected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense威 to be able to stop in time when the obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense威.


(Continued)


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165


WARNING! (Continued)


• Before using the ParkSense威 Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns the red LEDs ON. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.


CAUTION! (Continued)


• Clean the ParkSense威 sensors with water, car wash soap, and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Other- wise, you could damage the sensors.


WARNING!


• Drivers must be careful when backing up even when using the ParkSense威 Rear Park Assist Sys- tem. Always check carefully behind your vehicle, look behind you, and be sure to check for pedes- trians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.


(Continued)


166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enabling And Disabling ParkSense姞 There are times when you may want to disable Park- Sense威, such as when towing a trailer. Vehicles Equipped With The Electronic Vehicle Information Center (EVIC) You can turn ParkSense威 on or off through the EVIC. Refer to “Electronic Vehicle Information Center (EVIC)/ Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information. Vehicles Equipped With ParkSense威 Rear Park Assist Switch


You can turn ParkSense威 on or off by pressing the ParkSense威 Rear Park Assist switch located on the lower switch bank below the climate controls.


ParkSense姞 Operation ParkSense威 uses four sensors located in the rear bumper fascia to scan for obstacles up to 79 in (200 cm) away from the rear bumper fascia. The warning display located above the rear window provides both visible and audible warnings to indicate the range of the object.


ParkSense威 LED Display


The warning display contains two sets of yellow and red LEDs, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The driver can view the LEDs either through the rear view mirror or by looking at the display above the rear window. When the ignition is turned to the ON position, and the system is enabled, the warning display will turn on all of its LEDs for approximately one second. Then, the system dimly illuminates the two inner most LEDs when it is detecting no obstacles.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167
ParkSense威 is active when the ignition is in the ON position, and the system is enabled, and the driver shifts the transmission into the REVERSE position, and the vehicle speed is less than 11 mph (18 km/h). The following chart shows the warning display operation when the system is detecting an obstacle:


168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES


DISPLAY LED


OBSTACLE DISTANCE FROM:


LED COLOR


AUDIBLE SIGNAL


Inner LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED


REAR CORNERS


31.5 in (80 cm) 25.5 in (65 cm) 20 in (50 cm) 16 in (40 cm) 6 in (15 cm)


REAR CENTER 79 in (200 cm) 51 in (130 cm) 45 in (115 cm) 39 in (100 cm) 33.5 in (85 cm) 28 in (70 cm) 20 in (50 cm) 12 in (30 cm)


Yellow Yellow Yellow Yellow Yellow Yellow Red Red


Sounds for 1⁄2 second


None None None None None


Intermittent Continuous


Service ParkSense姞 Rear Park Assist When the ParkSense威 Rear Park Assist System is defec- tive, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the “SERVICE PARK ASSIST SYSTEM” message. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When


the shift lever is moved to REVERSE and the system has detected a faulted condition, the EVIC will display the “SERVICE PARK ASSIST SYSTEM” message for as long as the vehicle is in REVERSE. Under this condition ParkSense威 will not operate.


If “SERVICE PARK ASSIST SYSTEM” appears in the Electronic Vehicle Information Center (EVIC) after mak- ing sure the rear fascia/bumper is clean and clear of snow, ice, mud, dirt, or other obstruction, see your authorized dealer.


GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit operates off your vehicle’s battery. The HomeLink威 buttons that are located in the headliner or sun visor designate the three different HomeLink威 channels.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169


HomeLink威 Buttons


NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active.


170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


WARNING!


• Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety infor- mation or assistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death.


Programming HomeLink姞


Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. It is recommended that a new battery be placed in the handheld transmitter of the device that is being copied to HomeLink威 for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage when programming. 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the handheld transmitter away from the HomeLink威 button you wish to program.


Place the handheld transmitter 1–3 in (3-8 cm) away from the HomeLink威 button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen HomeLink威 button and the handheld transmitter button until the HomeLink威 indicator changes from a slow to a rapidly blinking light, then release both the HomeLink威 and handheld transmitter buttons. Watch for the HomeLink威 indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you train. NOTE: • Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171


• After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the ga- rage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, proceed to Step 5 “Programming A Rolling Code System.”


4. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLink威 button is pressed. If the indicator light blinks rapidly for two seconds, and then turns to a constant light, continue with program- ming for a Rolling Code. 5. Programming A Rolling Code System At the garage door opener motor (in the garage), locate the “Learn” or “Training” button.


172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door).


1 — Garage Door Opener 2 — Training Button


6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels.


Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink威” Step 3 with the following: 3. Continue to press and hold the HomeLink威 button, while you press and release (“cycle”), your handheld transmitter every two seconds until HomeLink威 has suc- cessfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained.


and release


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173
If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink威” earlier in this section. Using HomeLink姞 To operate, press the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, Security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time. Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position.


174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with Program- ming HomeLink威 Step 2 and follow all remaining steps. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active.


Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the LEARN button on the Garage Door Opener • Did you unplug the device for training, and remember


to complete the training for a Rolling Code.


to plug it back in?


If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.


2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. The term IC before the certification/registration number only signifies that Industry Canada technical specifica- tions were met.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175


POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console.


Power Sunroof Switch


176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


WARNING!


• Never leave unattended children in a vehicle with the key in the ignition switch. Occupants, particu- larly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In a collision, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. • Do not allow small children to operate the sun- roof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result.


Opening Sunroof — Express Press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automati- cally. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Opening Sunroof — Manual Mode To open the sunroof, press and hold the switch rearward to full open. Any release of the switch will stop the movement and the sunroof will remain in a partially opened condition until the switch is pushed and held rearward again.


Closing Sunroof — Express Press the switch forward and release it within one-half second and the sunroof will close automatically from any position. The sunroof will close fully and stop automati- cally. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. Closing Sunroof — Manual Mode To close the sunroof, press and hold the switch in the forward position. Any release of the switch will stop the movement and the sunroof will remain in a partially closed condition until the switch is pushed and held forward again. Pinch Protect Feature This feature will detect an obstruction in the opening of the sunroof during Express Close operation. If an ob- struction in the path of the sunroof is detected, the


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177
sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing and moves the sunroof in the opposite direction, press the switch forward and hold. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof — Express Press and release the ⬙Vent⬙ button within one-half sec- ond and the sunroof will open to the vent position. This is called “Express Vent”, and it will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.


178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) is in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sun- roof opening to minimize the buffeting or open any window.


Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. For vehicles equipped with the EVIC, the power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. The time is programmable. Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further information.


ELECTRICAL POWER OUTLET Your vehicle is equipped with a fused 12 Volt (13 Amp) power outlet. This power outlet is located on the instru- ment panel, below the climate controls. It has power available when the ignition switch is in the ON or ACC position. Insert the cigar lighter or accessory plug into the outlet for use to ensure proper operation. To preserve the heating element, do not hold the lighter in the heating position.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179


Front Power Outlet


NOTE: To ensure proper operation a MOPAR威 knob and element must be used.


180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


CAUTION!


• Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your warranty.


Power Outlet Fuse Location


M7 Fuse 20 A Yellow Cigar Lighter Instrument Panel


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181


CAUTION! (Continued)


• Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery. • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug.


WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an


the vehicle.


electric shock and failure.


CAUTION!


• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.


(Continued)


182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS There are two cupholders for the front seat passengers, located in the center console.


The rear passengers have cupholders at the rear of the center console.


Front Cupholders


Rear Cupholders


STORAGE


Glove Box Storage Compartment The glove box storage compartment is located on the right side of the instrument panel. Pull outward on the latch to open the storage compartment.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183


Front Storage Compartment The front storage compartment (located on the left side of the instrument panel) can hold cell phones, PDAs, and other small items.


Glove Box Storage Compartment


Front Storage Compartment


184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Storage Compartment To open, press the latch and lift the cover.


The center console has a removable storage tray which can hold cell phones, PDAs, and other small items.


Center Console


Removable Storage Tray


WARNING!


Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injury.


CARGO AREA FEATURES


Cargo Light The cargo area light is activated by opening the liftgate, opening any door, or by rotating the dimmer control on the multifunction lever to the extreme top position.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185


Cargo Tie-Down Hooks The tie-downs located on the cargo area floor should be used to safely secure loads when the vehicle is moving.


Cargo Tie-Downs


186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


WARNING!


Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or accident a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers.


WARNING!


The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling. To avoid loss of control resulting in per- sonal injury, follow these guidelines for loading your vehicle: • Do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar.


(Continued)


WARNING! (Continued)


• Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or be- come a dangerous projectile in a sudden stop or accident. • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts.


Cargo Load Floor — If Equipped


The panel in the load floor is reversible for added utility. One side features a plastic lined tray which can hold a variety of items. The maximum load capacity of the load floor is 400 lbs (181 kg). The cargo load floor is held by spring loaded latches. In order to use the cargo load floor, use the following procedure: 1. Push both side mounted release handles (toward the center of the vehicle) at the same time to release cover.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187


2. Lift the cover.


Floor Panel


188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Flip the cover over, and lock panel back into position. REAR WINDOW FEATURES Rear Window Wiper/Washer The rear wiper/washer is controlled by a rotary switch located on the control lever. The control lever is located on the right side of the steering column.


Load Floor


Rear Wiper/Washer Control


Rotate the switch upward to the first detent posi- tion for rear wiper operation.


NOTE: The rear wiper operates in an intermittent mode only.


Rotate the switch upward past the first detent to activate the rear washer. The washer pump will continue to operate as long as the switch is held (for a maximum of 10 seconds). Upon release, the wiper will cycle two times before returning to the set position. If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the “park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set. NOTE: The rear wiper and the rear washer will not operate If the liftgate flipper glass is open.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189


Rear Window Defroster


The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating.


CAUTION!


Failure to follow these cautions can cause damage to the heating elements:


(Continued)


190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


CAUTION! (Continued)


• Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window.


ROOF TRIM APPLIQUE — NON FUNCTIONAL The Roof Trim Applique as provided on the vehicle is non functional. Metal side rails and crossbars can be purchased from MOPAR威 accessories to provide a func- tional roof rack system.


The load carried on the roof, when equipped with a luggage rack, must not exceed 150 lbs (68 kg), and it should be uniformly distributed over the cargo area. Check the straps frequently to be sure that the load remains securely attached. NOTE: Metal rails/crossbars are offered by MOPAR威 accessories. See your authorized dealer. External racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the maximum vehicle load capacity.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191


WARNING!


Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack Cautions when carrying cargo on your roof rack.


CAUTION!


• To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as pos- sible and secure the load appropriately. • Long loads, which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle. • Place a blanket or other protection between the • Travel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward loads. This is especially true on large flat loads and may result in damage to the cargo or your vehicle.


surface of the roof and the load.


UNDERSTANDING YOUR INSTRUMENT PANEL


CONTENTS


䡵 Instrument Panel Features . . . . . . . . . . . . . . . 196
䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 197
䡵 Instrument Cluster Descriptions . . . . . . . . . . . 198
䡵 Compass And Trip Computer — If Equipped . . 212
▫ Control Buttons . . . . . . . . . . . . . . . . . . . . . 212
▫ Trip Conditions . . . . . . . . . . . . . . . . . . . . . 213
▫ Compass/Temperature Display . . . . . . . . . . 214


䡵 Electronic Vehicle Information Center (EVIC) —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 216
▫ Electronic Vehicle Information Center (EVIC)


Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
▫ Oil Change Required . . . . . . . . . . . . . . . . . . 219
▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . 219
▫ Compass Display / ECO


(Fuel Saver Mode) — If Equipped . . . . . . . . 221


▫ Personal Settings


(Customer-Programmable Features)


. . . . . . . 224


194 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Media Center 230 (REQ) — AM/FM Stereo


Radio And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . 227
▫ Operating Instructions - Radio Mode . . . . . . 227
▫ Operation Instructions - (Disc Mode For CD


And MP3/WMA Audio Play, DVD-Video) . . . 236
▫ Notes On Playing MP3/WMA Files . . . . . . . 238
▫ List Button


(Disc Mode For MP3/WMA Play) . . . . . . . . . 240


▫ Info Button (Disc Mode For MP3/WMA


Play)


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240


▫ Uconnect™ Multimedia


(Satellite Radio) — If Equipped . . . . . . . . . . 242


䡵 Media Center 730N/430/430N (RHR/RER/


RBZ/RHB) CD/DVD/HDD/NAV — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 246
▫ Operating Instructions


(Voice Command System) — If Equipped . . . 246


▫ Operating Instructions


(Uconnect™ Phone) — If Equipped . . . . . . . 246
䡵 Media Center 130 (Sales Code RES) . . . . . . . . . 247
▫ Operating Instructions — Radio Mode . . . . . 247
▫ Operation Instructions —


CD Mode For CD And MP3 Audio Play . . . . 250
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 252
▫ Operation Instructions - Auxiliary Mode . . . . 255


䡵 Media Center 130 With Satellite Radio


(Sales Code RES+RSC). . . . . . . . . . . . . . . . . . . 255
▫ Operating Instructions — Radio Mode . . . . . 256
▫ Operation Instructions — CD Mode For CD


And MP3 Audio Play . . . . . . . . . . . . . . . . . 261
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 263
▫ List Button (CD Mode For MP3 Play) . . . . . . 266
▫ Info Button (CD Mode For MP3 Play) . . . . . . 266
▫ Uconnect™ Multimedia (Satellite Radio) —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 267


UNDERSTANDING YOUR INSTRUMENT PANEL 195


䡵 Steering Wheel Audio Controls —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 271
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . 272
▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . 272
䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 273
䡵 Radio Operation And Mobile Phones . . . . . . . 273
䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 273
▫ Manual Heating And Air Conditioning . . . . . 274
▫ Automatic Temperature Control (ATC) —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 278
▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 283


196 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES


1 — Air Outlet 2 — Instrument Cluster 3 — Storage Tray 4 — Center Air Outlet 5 — Radio


6 — Glove Compartment 7 — Climate Control 8 — Heated Seat Switch * 9 — Rear Park Assist Switch * 10 — Passenger Airbag Disable Light


11 — Hazard Warning Flasher 12 — Electronic Stability Control / Traction Control Switch * 13 — Cigar Lighter / Power Outlet 14 — Storage Bin * If Equipped


INSTRUMENT CLUSTER


UNDERSTANDING YOUR INSTRUMENT PANEL 197


198 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS


1. Fuel Gauge The fuel gauge shows level of fuel in tank when ignition switch is in the ON/RUN position. 2. Fuel Door Reminder


This symbol indicates the side of the vehicle where the fuel cap is located.


3. Temperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.


The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.


CAUTION!


Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an autho- rized dealership for service.


WARNING!


A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see “Main- taining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph.


4. Low Fuel Light


When the fuel level reaches approximately 2.0 gal (7.8 L) this light will turn on, and remain on until fuel is added.


5. Seat Belt Reminder Light


When the ignition switch is first turned to ON/ RUN, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.


UNDERSTANDING YOUR INSTRUMENT PANEL 199
After the bulb check or when driving, if the driver’s seat belt remains unbuckled, the Seat Belt Reminder Light will illuminate and the chime will sound. Refer to “Occupant Restraints” in “Things To Know Before Start- ing Your Vehicle” for further information. 6. Engine Temperature Warning Light


This light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches H , this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H , the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the ve- hicle. If the temperature reading does not return to


200 UNDERSTANDING YOUR INSTRUMENT PANEL normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for further information. 7. Speedometer Shows the vehicles speed. 8. High Beam Indicator


This indicator shows that the high beam head- lights are on. Push the multifunction lever forward to switch the headlights to high beam, and pull toward yourself (normal position) to return to low beam. 9. Vehicle Security Light — If Equipped


This light will flash at a fast rate for approxi- mately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.


10. Electronic Stability Control (ESC) Activation/ Malfunction Indicator Light — If Equipped


The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position. It should go out with the engine running. If the “ESC Activation/Malfunction In- dicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. NOTE: • The “ESC Off


Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on mo- mentarily each time the ignition switch is turned to ON/RUN.


• Each time the ignition is turned to ON/RUN, the ESC system will be ON, even if it was turned off previously. • The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.


11. TOW/HAUL Indicator — If Equipped


The TOW/HAUL button is located on the gear shift bezel. This light will illuminate when the TOW/HAUL button has been selected.


12. Turn Signal Indicators


The arrow will flash with the exterior turn signal when the turn signal lever is operated.


UNDERSTANDING YOUR INSTRUMENT PANEL 201
If the vehicle electronics sense that the vehicle is driven more than 1 mile (1.6 km) with either turn signal on, a continuous chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 13. Transmission Temperature Warning Light — If Equipped


This light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. If this light comes on, stop the vehicle and run the engine at idle or faster with the transmission in NEU- TRAL until the light goes off.


CAUTION!


Continuous driving with the Transmission Tempera- ture Warning Light illuminated will eventually cause severe transmission damage or transmission failure.


202 UNDERSTANDING YOUR INSTRUMENT PANEL


WARNING!


If the Transmission Temperature Warning Light is illuminated and you continue operating the vehicle, in some circumstances you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.


14. Brake Warning Light


This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the


Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked.


If brake failure is indicated, immediate repair is neces- sary.


WARNING!


Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.


Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for ap- proximately two seconds. The light should then turn off


UNDERSTANDING YOUR INSTRUMENT PANEL 203
unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN posi- tion. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 15. Electronic Throttle Control (ETC) Light


This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position. The light should turn off. If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible. If


204 UNDERSTANDING YOUR INSTRUMENT PANEL the light is flashing when the engine is running, imme- diate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. The light will come on when the ignition is first turned to ON/RUN and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an autho- rized dealer. 16. Electronic Stability Control (ESC) OFF Indicator Light — If Equipped


This light indicates the Electronic Stability Con- trol (ESC) is off.


17. Charging System Light


This light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first turned to ON/RUN and remain on briefly as a bulb check. If the light stays on or comes on


while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an autho- rized dealer. If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. 18. SERV (Service) 4WD Indicator — If Equipped


The “SERV 4WD Indicator Light” will come on when the ignition key is turned to the ON/ RUN position and will stay on for two seconds. If the light stays on or comes on during driv- ing, it means that the 4WD system is not functioning properly and that service is required.


19. Anti-Lock Brake (ABS) Light


This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON/RUN position and may stay on for as long as four seconds.


If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the ignition switch is turned to the ON/RUN position, have the light inspected by an authorized dealer. 20. Front Fog Light Indicator — If Equipped


This indicator will illuminate when the front fog lights are On.


UNDERSTANDING YOUR INSTRUMENT PANEL 205


21. Oil Pressure Warning Light


This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood. 22. Air Bag Warning Light


This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information.


206 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Tachometer This gauge measures engine revolutions-per-minute (RPM x 1000). When the engine RPM are kept within the green area, you are driving the vehicle in a fuel efficient manner. Before the pointer reaches the red area, ease up on the accelerator to prevent engine damage. 24. Shift Lever Indicator The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. 25. Tire Pressure Monitoring Telltale Light


Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle


has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.


Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the


UNDERSTANDING YOUR INSTRUMENT PANEL 207
TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.


CAUTION!


The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.


208 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Odometer / Trip Odometer Display Area The odometer display shows the total distance the ve- hicle has been driven. The trip odometer shows indi- vidual trip mileage. Refer to “Trip Odometer Button” for additional information. NOTE: U.S. Federal regulations require that upon trans- fer of vehicle ownership, the seller certify to the pur- chaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero.


Vehicle Odometer Messages When the appropriate conditions exist, the following messages will display in the odometer:


ECO . . . . . . . . . . . . . . . . . . . Fuel Saver Indicator Off ECO-ON . . . . . . . . . . . . . . . . Fuel Saver Indicator On door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Ajar gATE . . . . . . . . . . . . . . . . . . . . . . . . . . . Liftgate Ajar gASCAP . . . . . . . . . . . . . . . . . . . . . . . Fuel Cap Fault noFUSE . . . . . . . . . . . . . . . . . . . . . . . . . . Fuse Fault CHAngE OIL . . . . . . . . . . . . . . . Oil Change Required LoWASH . . . . . . . . . . . . . . . . . . . . Low Washer Fluid On vehicles equipped with a Premium Instrument Clus- ter, this display shows the Electronic Vehicle Information Center (EVIC) messages when the appropriate conditions exist. Refer to Electronic Vehicle Information Center (EVIC) for further information.


ECO / ECO-ON (Fuel Saver Indicator) — If Equipped The ECO-ON indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify driving habits in order to increase fuel economy. The ECO display will toggle between ECO and ECO-ON depending on driving habits and vehicle usage. Press the Odometer / Trip Odometer / ECO (Fuel Saver Indicator) button to change the display from odometer to either of the two trip odometer settings or the “ECO” display. gASCAP Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, “gASCAP” will be displayed in the odometer display area. Tighten the fuel filler cap properly and press the odometer reset button to turn the gASCAP message off. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL).


UNDERSTANDING YOUR INSTRUMENT PANEL 209


noFUSE If the vehicle diagnostic system determines that the Ignition Off Draw (IOD) fuse is improperly installed, or damaged, a “noFUSE” message will display in the odom- eter display area. For further information on fuses and fuse locations refer to “Fuses” in “Maintaining Your Vehicle”. CHAngE OIL Message Your vehicle is equipped with an engine oil change indicator system. The “CHAngE OIL” message will flash in the instrument cluster odometer for approximately 12 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the TRIP


210 UNDERSTANDING YOUR INSTRUMENT PANEL ODOMETER button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following proce- dure:


1. Turn the ignition switch to the ON/RUN position. Do not start the engine. 2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the OFF/LOCK position. If the indicator message illuminates when you NOTE: start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. 27. Malfunction Indicator Light (MIL)


The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBD, that monitors engine and automatic transmission con- trol systems. The light will illuminate when the key is in


the ON/RUN position, before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing.


CAUTION!


Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.


WARNING!


29. Odometer / Trip Odometer / ECO (Fuel Saver Indicator) Button


UNDERSTANDING YOUR INSTRUMENT PANEL 211


A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others.


28. Cruise Indicator — If Equipped This indicator lights when the electronic speed control system is turned on.


Changing the Display Press this button to change the display from odometer to either of the two trip odometer settings or the “ECO” display. Trip A or Trip B will appear when in the trip odometer mode. On vehicles equipped with a Base Cluster, press and release it once again to display the outside temperature. On vehicles equipped with a Mid Line Cluster, press and release it once again to display the outside temperature and compass heading in the screen below the speedometer. Refer to “Compass/Trip Com- puter” for details. Resetting the Trip Odometer Display the trip mileage that you want to reset, “Trip A” or “Trip B.” Then push and hold the button (approxi- mately two seconds) until the display resets to 0. The odometer must be in Trip Mode to reset the trip odometer.


located on the lower left part of the cluster below the fuel and engine temperature gauge, and the tachometer.


212 UNDERSTANDING YOUR INSTRUMENT PANEL 30. Compass/Trip Computer or Electronic Vehicle Information Center (EVIC) Display — If Equipped When the appropriate conditions exist, this display shows the Compass/Trip Computer or Electronic Vehicle Information Center (EVIC) messages. For further information, refer to “Compass/Trip Com- puter” or Information Center (EVIC)”. 31. 4WD Indicator — If Equipped


“Electronic Vehicle


This light indicates the vehicle is in four-wheel drive and 4LOCK. 4WD allows all four wheels to engine simultaneously.


from the


receive


torque


COMPASS AND TRIP COMPUTER — IF EQUIPPED The Compass/Trip Computer a driver- interactive display (displays information on outside tem- perature, compass direction, and trip information). It is


features


Compass/Trip Computer Display


Control Buttons Press and release the odometer/trip odometer reset but- ton (right side of the instrument cluster) to access the compass/trip computer displays.


NOTE: The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated tempera- ture is displayed. Engine temperature can also affect the displayed temperature; therefore, temperature readings are not updated when the vehicle is not moving.


Display Button


UNDERSTANDING YOUR INSTRUMENT PANEL 213
The compass/trip computer, when the appropriate con- ditions exist, will show the following messages in the odometer display: • Door Ajar (door) • Lift Gate Ajar (gATE) • Loose Fuel Cap (gASCAP) These messages can be manually turned off by pressing the right button (on the instrument cluster). Trip Conditions


Trip Odometer (ODO) / ECO (Fuel Saver Indicator) — If Equipped This display shows the distance traveled since the last reset. Press and release the right button (on the instru- ment cluster) to switch from odometer to Trip A or Trip B or to ECO. Press and hold the right button while the odometer/trip odometer is displayed to reset.


214 UNDERSTANDING YOUR INSTRUMENT PANEL Trip A Shows the total distance traveled for trip A since the last reset. Trip B Shows the total distance traveled for trip B since the last reset. ECO (Fuel Saver Indicator) — If Equipped The ECO-ON indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify driving habits in order to increase fuel economy. The ECO display will toggle between ECO and ECO-ON depending on driving habits and vehicle usage.


Compass/Temperature Display


Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the

Loading...
x