2008 Chrysler Pacifica Owners Manual

† PARK BRAKE ENGAGED (with a single chime) † LOW BRAKE FLUID (with a single chime) † LOW FUEL (with a single chime) † MENU IN PARK ONLY † LIST # ALERT MESSAGES

chime)

† UNLOCK TO OPEN LIFTGATE (with a single chime) † PUT IN PARK FOR LIFTGATE (with a single chime) † TOO COLD FOR PWR LIFTGATE (with a single † TOO HOT FOR PWR LIFTGATE (with a single chime) † PERFORM SERVICE (with a single chime) † LEFT/RIGHT FRONT DOOR AJAR (one or more, † LEFT/RIGHT REAR DOOR AJAR (one or more, with a single chime if speed is above 1 mph) † DOOR(S) AJAR (with a single chime) † DOOR(S) AND GATE AJAR (with a single chime) † LIFT GATE AJAR (with a single chime if speed is

with a single chime if speed is above 1 mph)

above 1 mph)

chime)

† WASHER FLUID LOW (with a single chime) † PEDAL ADJUST DISABLED CRUISE ENGAGED † PEDAL ADJUST DISABLED VEHICLE IN REVERSE † CHANNEL 1, 2, OR 3 TRANSMIT (with a single † CHANNEL 1, 2, OR 3 TRAINING (with a single † CHANNEL 1, 2, OR 3 TRAINED (with a single chime) † CLEARING CHANNELS † CHANNELS CLEARED † CHANNELS DEFAULTED † DID NOT TRAIN

chime)

UNDERSTANDING YOUR INSTRUMENT PANEL 201

† 1,2,3 OR 4 TIRE(S) LOW PRESSURE (Refer to ”Tire Pressure Monitor System” in the “Starting And Oper- ating, Tire Section”) † SERVICE TIRE SYSTEM SOON (Refer to ”Tire Pres- sure Monitor System” in the “Starting And Operating, Tire Section”) † TCS SUSPENDED (Traction Control System, with a † TCS ACTIVE (Traction Control System, with a † SERVICE TCS SYSTEM (Traction Control System, with

graphic and single chime)

graphic)

a graphic and single chime)

202 UNDERSTANDING YOUR INSTRUMENT PANEL

Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Required” message will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the Menu button. To reset the oil change indicator system (after performing the scheduled maintenance) perform the following procedure: 1. Turn the ignition switch to the “ON” position (Do not start the engine).

2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the “LOCK” position. If the indicator message illuminates when you NOTE: start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. NOTE: † The oil change indicator system will not monitor the time since the last oil change. Change the engine oil if it has been 6 months since your last oil change even if the oil change indicator message is NOT illuminated. † Change the engine oil more often if you drive your † Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first.

vehicle off-road for an extended period.

Customer Programmable Features — If Equipped Press the MENU button until one of the following display choices appears: Language? When in this display you may select one of three lan- guages for all display nomenclature, including the trip computer functions and navigation system. Press the STEP button while in this display selects English, Francais, or Espanol. As you continue the displayed information will be shown in the selected language. Park Assist System? ON/OFF When this feature is selected the system scans for objects behind the vehicle using four sensors located in the rear bumper. Objects can be detected from up to 59 inches (150 cm). Pressing the “STEP” button while in this display will disable/enable the Rear Park Assist System. The EVIC will display the following message: PARK

UNDERSTANDING YOUR INSTRUMENT PANEL 203

ASSIST DISABLED after the feature has been disabled and SERVICE PARK ASSIST SYSTEM if there is a prob- lem with the system. Service Interval When this feature is selected a service interval between 2,000 miles (3 200 km) and 6, 000 miles (10 000 km) in 500
mile (800 km) increments may be selected. Pressing the STEP button when in this display will select distances between 2,000 miles (3 200 km) and 6, 000 miles (10 000
km) in 500 mile (800 km) increments. Reset Service Distance (Displays Only if Service Interval was Changed) When this feature is selected the current accumulated service distance can be reset to the newly selected service interval. Pressing the STEP button when in this display will select “Yes” or “No.”

204 UNDERSTANDING YOUR INSTRUMENT PANEL

Use factory Settings? When in this display you may select to use the factory settings and no programmable features will be offered. Tilt Mirrors in Reverse? (Available with Memory Seat Only) When this feature is selected the outside mirrors will move slightly downward from the present position when the vehicle is shifted into the Reverse position. The outside mirrors will then return to the original position when the vehicle is shifted out of Reverse position. Pressing the STEP button when in this display will select 9Yes9 or 9No9. Auto Door Locks? When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches 15 mph (25 km/h). Pressing the STEP button when in this display will select “Yes” or “No.”

Auto Unlock On Exit? When this feature is selected all the vehicle’s doors will unlock when the driver’s door is opened if the vehicle is stopped and the transmission is in P (Park) or N (Neu- tral) position. Pressing the STEP button when in this display will select “Yes” or “No.” Remote Unlock Driver’s Door 1st? When this feature is selected only the driver’s door will unlock on the first press of the remote keyless entry unlock button and require a second press to unlock the remaining locked doors and liftgate. When REMOTE UNLOCK ALL DOORS is selected all of the doors and the liftgate will unlock at the first press of the remote keyless entry unlock button. Pressing the STEP button when in this display will select DRIVER’S DOOR 1ST or ALL DOORS.

Remote Linked To Memory? (Available with Memory Seat Only) When this feature is selected the memory seat, mirror, and radio settings will return to the memory set position when the remote keyless entry “Unlock” button is pressed. If this feature is not selected then the memory seat, mirror, and radio settings can only return to the memory set position using the door mounted switch. Pressing the STEP button when in this display will select “Yes” or “No.” Sound Horn On Lock? When this feature is selected a short horn sound will occur when the remote keyless entry “Lock” button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. Pressing the STEP button when in this display will select “Yes” or “No.”

UNDERSTANDING YOUR INSTRUMENT PANEL 205

Flash Lights On Lock/Unlock? When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter. This feature may be selected with or without the sound horn on lock feature selected. Pressing the STEP button when in this display will select “Yes” or “No.” Headlamp Delay When this feature is selected the driver can choose, when exiting the vehicle, to have the headlamps remain on for 30, 60, or 90 seconds, or not remain on. Pressing the STEP button when in this display will select 30, 60, 90, or OFF. Headlamp On With Wipers? (Available with Auto Headlights Only) When this feature is selected and the headlight switch has at least once been moved to the AUTO position, the headlights will turn on in approximately 10 seconds when the wipers are turned on. The headlights will also

206 UNDERSTANDING YOUR INSTRUMENT PANEL

turn off when the wipers are turned off if they were turned on in this way. Pressing the STEP button when in this display will select “Yes” or “No.” NOTE: Turning the headlights on during the daytime causes the instrument panel lights to dim. To increase the brightness, refer to “Lights” in this section. Power Accessory Delay? When this feature is selected, the power window switches, radio, hands–free system, DVD video system, power sunroof, and power outlets will remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle door or liftgate will cancel this feature. Easy Exit Seat? (Available with Memory Seat Only) This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle.

The Easy Entry Easy Exit feature is not enabled when the vehicle is delivered from the factory. The Easy Entry Easy Exit feature is enabled (or later disabled) through the programmable features in the Electronic Vehicle Informa- tion Center (EVIC). Pressing the STEP button when in this display will select “Yes” or “No.” The seat will return to the memorized seat location (if REMOTE LINK TO MEMORY is set to YES) when the remote keyless entry transmitter is used to unlock the door. For more informa- tion refer to “Easy Entry/Exit Seat in the Driver Memory Seat section. Display U.S. or Metric? Pressing the US/M button will change the EVIC, odom- eter, navigation system and A/C Control units from US to Metric.

Compass Display — If Equipped This display provides one of eight compass readings to indicate the direction the vehicle is facing. Automatic Compass Calibration This compass is self-calibrating which eliminates the need to manually calibrate the compass. When the ve- hicle is new, the compass may appear erratic and the EVIC will display “COMPASS CALIBRATING” until the compass is calibrated. The compass will function nor- mally. To calibrate the compass, drive the vehicle in one or more complete 360° circles, under 5 mph (8 km/h) in an area free from large metal objects, until the “COMPASS CALI- BRATING” message turns off. Manual Compass Calibration If the compass appears erratic, inaccurate or abnormal, you may wish to manually calibrate the compass. Prior to calibration, make sure the proper zone is selected.

UNDERSTANDING YOUR INSTRUMENT PANEL 207

To put into a Calibration Mode: Turn on the ignition switch and set the display to Compass. Press the RESET button for at least 10 seconds until the “COMPASS CALIBRATING” message appears. Release the MENU button and drive the vehicle in one or more complete three, 360° circles, under 5 mph (8 km/h) in an area free from large metal objects, until the “COMPASS CALI- BRATING” message turns off. Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings. In order to ensure accuracy, the compass vari- ance should be properly set according to the compass variance zone that the vehicle is in.

208 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE: Magnetic materials should be kept away from the overhead console.

To set the variance: Turn the ignition switch ON and set the display to Compass. Press the MENU button for approximately 5 seconds but no more than 10 seconds. The “COMPASS VARIANCE” message and the last vari- ance zone number will be displayed. Press the STEP button to select the proper variance zone as shown in the map. Press the RESET button to set the new variance zone and resume normal operation. Mini-Trip Functions — If Equipped This displays information on the following: † Average Fuel Economy (ECO AVG) Shows the average fuel economy since the last reset. The minimum average fuel economy that will be displayed on reset is 0.3 mpg. † Distance To Empty (DTE) Shows the estimated distance that can be travelled with the fuel remaining in the tank. This estimated distance is determined using the MPG for the last few minutes.

† Off Mode Shows a blank display. † Step Button Push this button to cycle through all functions. To Reset The Display Pressing and releasing the Reset button once will clear the resettable function currently being displayed. The resettable function is average fuel economy. Reset will only occur if the resettable function is currently being displayed.

the Mini-trip

UNDERSTANDING YOUR INSTRUMENT PANEL 209

SETTING THE ANALOG CLOCK

To set the analog clock, at the top center of the instrument panel, press and hold the but- ton until the setting is correct. The clock will adjust slowly at first and then quicker the longer the button is held.

ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes.

210 UNDERSTANDING YOUR INSTRUMENT PANEL

On vehicles equipped with an Analog Clock the radio time display will function as follows: † Radio On — Radio clock will display for approxi- mately 5 seconds after button is pressed, then default back to radio frequency. † Radio Off — Radio clock will display for approxi- mately 5 seconds after button is pressed, then default back to blank screen.

The following radio time options can be changed by your dealer service department: † Radio On — Radio clock will continue to be displayed † Radio Off — Radio clock will displayed continuously.

after button is pressed.

Clock Setting Procedure

1. Turn the ignition switch to the ON or ACC position and press the time button. Using the tip of a ballpoint pen or similar object, press either the hour (H) or minute (M) buttons on the radio. 2. Press the H button to set hours or the M button to set minutes. The time setting will increase each time you press a button.

RADIO GENERAL INFORMATION

Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning. To help

you understand and save you concern about these “ap- parent” malfunctions, you must understand a point or two about the transmission and reception of radio sig- nals. Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal.

UNDERSTANDING YOUR INSTRUMENT PANEL 211

AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs. FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio. NOTE: The radio, steering wheel radio controls (if equipped), and 6 disc CD/DVD changer (if equipped) will remain active for up to 90 seconds after the ignition switch has been turned off, depending upon the acces- sory delay setting. Opening a vehicle front door will cancel this feature.

212 UNDERSTANDING YOUR INSTRUMENT PANEL

SALES CODE RAH — AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS

NOTE: The radio sales code is located on the lower left side of your radio faceplate.

Radio Operation

Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. PTY (Program Type) Pressing the INFO button once while in FM mode will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out, the PTY icon will turn off. Pressing the TUNE button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.

RAH radio

Toggle the TUNE button to select the following format types:

Program Type

Radio Display

Adult Hits Classical Classic Rock College Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music

Adult Hit Classical Classic Rock College Country Inform Jazz Language News Nostalgia Oldies Personality Public R & B Religious Music

UNDERSTANDING YOUR INSTRUMENT PANEL 213

Program Type

Radio Display

Religious Talk Rock Soft Soft Rock Soft R&B Sports Talk Top 40
Weather

Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40
Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM and Satellite (if equipped) modes. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If

214 UNDERSTANDING YOUR INSTRUMENT PANEL

no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station. Mode Press the MODE button to select between, AM, FM, CD, CD/DVD changer or the Satellite Radio (if equipped). When the Satellite Radio (if equipped) is selected “SA” will appear in your radio display. A disc may remain in the radio while in the Satellite or radio mode. Seek Press and release the SEEK button to search for the next station in either the AM, FM or Satellite mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you

make another selection. Holding the button in will by- pass stations without stopping until you release it. Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Balance The Balance control adjusts the left-to-right speaker bal- ance. Press the AUDIO button, select BALANCE, then press SEEK + or SEEK 2 to adjust the balance. Fade The Fade control provides for balance between the front and rear speakers. Press the AUDIO button, select FADE, then press SEEK + or SEEK 2 to adjust the fade balance.

Tone Control The Bass and/or Treble controls sound for the desired tone. Press the AUDIO button, select Bass or TREBLE, then press SEEK + or SEEK 2 to increase or decrease amplification of the band. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button. If a station is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in

UNDERSTANDING YOUR INSTRUMENT PANEL 215

both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into memory. You can recall the stations stored in SET 2 memory by pressing the push- button twice. To Change From Clock To Radio Mode Press the TIME button to change the display between radio frequency and time. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.

216 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE: Changes or modifications not expressively ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: † The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. † This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.

Inserting The Compact Disc

CAUTION!

This CD player will accept only 4–3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.

You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one.

Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear. The disc can be ejected with the radio OFF. FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW (Reverse) button works in a similar manner.

UNDERSTANDING YOUR INSTRUMENT PANEL 217

RND — Random Play Press the RND button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press TUNE FF to fast forward through the tracks. Press the FF button a second time to stop the fast forward feature. If TUNE RW is pressed, the current track will reverse to the beginning of the track and begin playing. Press the RND button a second time to stop Random Play.

218 UNDERSTANDING YOUR INSTRUMENT PANEL

CD/DVD Changer Operation Press the MODE button to select between the CD player and the optional remote CD/DVD changer. Time Press the TIME button to change the display from elapsed CD or DVD playing time to time of day. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3
file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported media (disc types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW. Supported medium formats (file systems) The medium formats supported by the radio are ISO 9660
Level 1 and Level 2 and includes the Joliet extension.

When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: † Maximum number of directory levels: 15
† Maximum number of files: 255
† Maximum number of folders: 100
† Maximum number of characters in file/folder names: † Level 1: 12 (including a separator 9.9 and a 3
† Level 2: 31 (including a separator 9.9 and a 3

character extension)

character extension)

Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal

CD audio tracks and computer files (including MP3 files). Discs created with an option such as 9keep disc open after writing9 are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 file formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.mp3
extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.

UNDERSTANDING YOUR INSTRUMENT PANEL 219

MPEG

Specification

Sampling Fre- quency (kHz)

MPEG-1 Audio

Layer 3

48, 44.1, 32

MPEG-2 Audio

Layer 3

24, 22.05, 16

Bit rate (kbps)

320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32
160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24,

16, 8

ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.

220 UNDERSTANDING YOUR INSTRUMENT PANEL

Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: † Media - CD-RW media may take longer to load than † Medium formats - Multisession discs may take longer † Number of files and folders - Loading times will

to load than non-multisession discs

CD-R media

increase with more files and folders

To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the Disc at Once option before writing to the disc.

Operation Instructions - (CD Mode For MP3 Audio Play)

SEEK Button (CD Mode For MP3 Play) Pressing the SEEK + button plays the next MP3 File. Pressing the SEEK 2 button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file. INFO Button (CD Mode For MP3 Play) Press and INFO button while playing MP3 disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if avail- able). Press the INFO button once more to return to 9elapsed time9 priority mode.

RW/FF (CD Mode For MP3 Play) Press the FF side of the button to move forward through the MP3 selection. Press the RW side of the button to move back through the MP3 selection. AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode. RND Button (CD Mode For MP3 Play) Pressing this button plays files randomly. DIR Button (CD Mode For MP3 Play) Press the DIR Button to display folders, when playing an MP3 discs that have a file/folder structure. Press DISC up (button 1) or DISC down (button 5) to move through the folders. Press the SET button to select a folder.

UNDERSTANDING YOUR INSTRUMENT PANEL 221

Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone section of the Owner’s Manual. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of Manual. Operating Instructions - Video Entertainment System (VESt) (If Equipped) Refer to 6 Disc CD/DVD Changer (RDV) section of the Owner’s Manual.

the Owner’s

222 UNDERSTANDING YOUR INSTRUMENT PANEL

SALES CODE REV — AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS

NOTE: The radio sales code is located on the lower left side of your radio faceplate.

Radio Operation

Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. PTY (Program Type) Pressing the INFO button once while in FM mode will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out, the PTY icon will turn off. Pressing the TUNE button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.

REV Radio

Toggle the TUNE button to select the following format types:

Program Type

Radio Display

Adult Hits Classical Classic Rock College Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music

Adult Hit Classical Classic Rock College Country Inform Jazz Language News Nostalgia Oldies Personality Public R & B Religious Music

UNDERSTANDING YOUR INSTRUMENT PANEL 223

Program Type

Radio Display

Religious Talk Rock Soft Soft Rock Soft R & B Sports Talk Top 40
Weather

Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40
Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM and Satellite (if equipped) modes. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If

224 UNDERSTANDING YOUR INSTRUMENT PANEL

no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station. Mode Press the MODE button to select between, AM, FM, CD, CD/DVD changer or the Satellite Radio (if equipped). When the Satellite Radio (if equipped) is selected “SA” will appear in your radio display. A disc may remain in the radio while in the Satellite or radio mode. Seek Press and release the SEEK button to search for the next station in either the AM, FM or Satellite mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you

make another selection. Holding the button in will by- pass stations without stopping until you release it. Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Balance The Balance control adjusts the left-to-right speaker bal- ance. Press the AUDIO button, select BALANCE, then press SEEK + or SEEK 2 to adjust the balance. Fade The Fade control provides for balance between the front and rear speakers. Press the AUDIO button, select FADE, then press SEEK + or SEEK 2 to adjust the fade balance.

Tone Control The Bass and/or Treble controls sound for the desired tone. Press the AUDIO button, select Bass or TREBLE, then press SEEK + or SEEK 2 to increase or decrease amplification of the band. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button. If a station is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in

UNDERSTANDING YOUR INSTRUMENT PANEL 225

both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into memory. You can recall the stations stored in SET 2 memory by pressing the push- button twice. To Change From Clock To Radio Mode Press the TIME button to change the display between radio frequency and time. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.

226 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE: Changes or modifications not expressively ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: † The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. † This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW) compact discs with MP3 tracks and multi-session compact discs with CD and MP3 tracks.

Inserting The Compact Disc

CAUTION!

This CD player will accept only 4–3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.

You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one.

Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode. If you do not remove the disc within 15 seconds, it will be reloaded. The radio mode will continue to appear. The disc can be ejected with the radio OFF. FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW (Reverse) button works in a similar manner.

UNDERSTANDING YOUR INSTRUMENT PANEL 227

RND — Random Play Press the RND button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press TUNE FF to fast forward through the tracks. Press the FF button a second time to stop the fast forward feature. If TUNE RW is pressed, the current track will reverse to the beginning of the track and begin playing. Press the RND button a second time to stop Random Play.

228 UNDERSTANDING YOUR INSTRUMENT PANEL

CD/DVD Changer Operation Press the MODE button to select between the CD player and the optional remote CD/DVD changer. Time Press the TIME button to change the display from elapsed CD or DVD playing time to time of day. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3
file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported media (disc types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW. Supported medium formats (file systems) The medium formats supported by the radio are ISO 9660
Level 1 and Level 2 and includes the Joliet extension.

When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: † Maximum number of directory levels: 15
† Maximum number of files: 255
† Maximum number of folders: 100
† Maximum number of characters in file/folder names: † Level 1: 12 (including a separator 9.9 and a 3
† Level 2: 31 (including a separator 9.9 and a 3

character extension)

character extension)

Multi-session disc formats are supported by the radio. Multi-session discs may contain combinations of normal

CD audio tracks and computer files (including MP3 files). Discs created with an option such as 9keep disc open after writing9 are most likely multi-session discs. The use of multi-session for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 file formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.mp3
extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.

UNDERSTANDING YOUR INSTRUMENT PANEL 229

MPEG

Specification

Sampling Fre- quency (kHz)

MPEG-1 Audio

Layer 3

48, 44.1, 32

MPEG-2 Audio

Layer 3

24, 22.05, 16

Bit rate (kbps)

320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32
160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24,

16, 8

ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.

230 UNDERSTANDING YOUR INSTRUMENT PANEL

Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: † Media - CD-RW media may take longer to load than † Medium formats - Multi-session discs may take longer † Number of files and folders - Loading times will

to load than not multi-session discs

CD-R media

increase with more files and folders

To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the Disc at Once option before writing to the disc.

Operation Instructions - (CD Mode For MP3 Audio Play)

SEEK Button (CD Mode For MP3 Play) Pressing the SEEK + button plays the next MP3 File. Pressing the SEEK 2 button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file. INFO Button (CD Mode For MP3 Play) Press and INFO button while playing MP3 disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if avail- able). Press the INFO button once more to return to 9elapsed time9 priority mode.

RW/FF (CD Mode For MP3 Play) Press the FF side of the button to move forward through the MP3 selection. Press the RW side of the button to move back through the MP3 selection. AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode. RND Button (CD Mode For MP3 Play) Pressing this button plays files randomly. DIR Button (CD Mode For MP3 Play) Press the DIR Button to display folders, when playing an MP3 discs that have a file/folder structure. Press DISC up (button 1) or DISC down (button 5) to move through the folders. Press the SET button to select a folder. Operating Instructions - Hands Free Phone (If Equipped) Refer to Hands Free Phone section of the Owner’s Manual.

UNDERSTANDING YOUR INSTRUMENT PANEL 231

the Owner’s

Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of Manual. Operating Instructions — MP3 Player, Portable Walkman An MP3 player can be connected to the audio system. Connect the cables to the RCA jacks located on the front of the CD/DVD changer. NOTE: Follow the manufactures instructions for the correct colors when connecting the RCA cables. (Refer to the illustration below). Operating Instructions — Video Games/Camcorders A video game unit or camcorder can be connected to the rear audio/video system. Connect the cables to the RCA jacks located on the front of the CD/DVD changer.

232 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE: To operate a video game unit a DC to AC adapter may be required, plug the adapter into any power outlet.

Listed below is the standard RCA Jack/Cable connection. You may also to refer to the manufacture’s want instructions the correct colors when connecting the RCA cables.

for

1. Video in (yellow) 2. Left audio in (white) 3. Right audio in (red) NOTE: MP3 player’s, video game systems, camcorders connected to the RCA jacks and CD’s or DVD’s inserted into the radio, can be heard through the headphones or the cabin when AUX Mode is selected.

6 DISC CD/DVD CHANGER (RDV) — IF EQUIPPED The Rear Seat Audio/Video System allows passengers to listen to a CD or DVD from the 6 disc CD/DVD changer through wireless headphones, while the front seat pas- sengers listen to either AM/FM, Cassette or CDs from the radio speakers. A remote control is provided for func- tions such as changing tracks or DVD functions, as well as selecting discs loaded in the 6 disc CD/DVD changer while listening to the Rear Audio/Video System. The Rear Seat Audio/Video System may be available in a base and premium version. The premium version in- cludes a six disc changer, remote control and two sets of wireless headphones. The base version includes a single disc player and remote control. The CD/DVD Changer will play CD-R, CD-RW, CD- Audio and DVD Video disc formats. The video screen will turn on automatically once a DVD is inserted into the changer.

NOTE: The ignition switch must be in the ON or ACC position before the CD/DVD changer will operate.

Operating Instructions — CD/DVD Changer

Loading The CD/DVD Changer

UNDERSTANDING YOUR INSTRUMENT PANEL 233

The premium version has a multi-disc changer, and will accept up to six discs. The base version is a single-disc player, and will only accept one disc.

To insert disc(s) into the changer, follow the instructions shown: 1. On vehicles equipped with the premium version, select and press any numbered button without an illumi- nated light above it. 2. Gently insert the disc with the label facing up while the light below the loading slot is illuminated. On vehicles equipped with the premium version the light above the chosen button will also be flashing, indicating

Six Disc DVD Changer

234 UNDERSTANDING YOUR INSTRUMENT PANEL

which numbered position the disc will be loaded into. The disc will automatically be pulled into the CD/DVD changer. 3. Upon insertion, the disc will begin to play, and the light below the loading slot will turn off. On vehicles equipped with the premium version the light above the chosen button will remain illuminated. 4. Repeat the process for loading any additional CD/ DVDs into the premium version multi-disc changer. The CD/DVD changer will stop while additional CD/DVDs are loaded. If the radio volume control is ON, the unit will switch from radio to CD/DVD mode and the video screen will turn on. If the DVD supports the autoplay feature, play will begin automatically in approximately 10 seconds, after the DVD disc menu is displayed. If the DVD does not play automatically, press the ENTER button on the remote control or on the side of the video screen to select

play from the menu options. The radio display will show the chapter number and index time in hours and minutes of the DVD, or the track number, minutes and second of the CD. NOTE: † You may eject a disc with the radio OFF. † If you insert a disc with the ignition ON and the radio OFF, the DVD will automatically be pulled into the DVD changer and the display will show the time of day. † It is recommended to label home made burned discs with a permanent marker instead of adhesive labels. These types of labels may become loose and cause the disc to be stuck in the DVD player. This may cause permanent damage to the DVD mechanism.

EJECT (EJT) Button If there is a disc in the changer, press the EJT button and the disc will eject. If you do not remove the disc within 10
seconds, it will be reloaded and the display will show PAUSE. The radio mode will continue to operate. To eject additional discs from the premium version multi-disc changer, first select the numbered button where the disc is located and then press the EJT button. Operating Instructions — Remote Control

NOTE: Aim the remote control at the radio located on the center of the instrument panel and press the desired button. Direct sunlight or objects blocking the line of sight may affect the function of the remote control.

UNDERSTANDING YOUR INSTRUMENT PANEL 235

Remote Control

236 UNDERSTANDING YOUR INSTRUMENT PANEL

Remote Control Buttons

1. Headphone Transmitter 2. Menu Up/Next Track/Chapter 3. Menu Left/Fast Rewind 4. Return 5. Setup 6. Pause/Play 7. Mute 8. Display 9. Mode 10. Program Down - Previous Disc 11. Program Up - Next Disc 12. Slow 13. Stop 14. Menu 15. Menu Down/Previous Track/Chapter 16. Menu Right/Fast Forward

Remote Control Buttons

17. Enter 18. Light Headphone Transmitter Button (1) The headphone transmitter button on the remote control and the power button on the headphones must be turned ON before sound can be heard from the headphones. On some radios the headphone symbol will flash for ap- proximately 5 seconds in the radio display, indicating the headphones are in use. ARROW Buttons (2, 3, 15, 16) These arrow buttons only function in CD/ DVD mode. Use the arrow buttons to toggle through the disc menu screen options.

RTN Button (4) This button only functions in CD/DVD mode. Press this button to return to the previous menu when in the disc menu mode. SETUP Button (5) This button only functions in CD/DVD mode. Press the button after pressing the STOP button to access the set up menu. Use the right and left arrows to move between tabs for language, rating, mark, audio and aspect. Use the up and down arrows to move between options within each tab. To change an item highlighted in blue, press ENTER. This should cause the highlight to turn yellow. Again, using the up and down arrows will cause the arrow to move up or down. Once the arrow is on the desired selection, press ENTER. When finished, press setup or play to return to playing the CD/DVD or Menu to return to the disc menu.

UNDERSTANDING YOUR INSTRUMENT PANEL 237

PAUSE/PLAY Button (6) This button only functions in DVD video mode. Press this button once to pause the video, press a second time to play the video. MUTE Button (7) This button mutes audio playing through the DVD player. DISP Button (8) This button only functions in DVD video mode. When a DVD video is playing, press this button to display the play menu options. MODE Button (9) † With DVD Radio (REV) and DVD changer, this button changes between radio DVD, Radio AUX Jacks and DVD changer input.

† All other radios: No Function.

238 UNDERSTANDING YOUR INSTRUMENT PANEL

This button changes between available modes and can be heard in the headphones. PROG UP/DOWN Buttons (10, 11) PROG UP selects the next disc loaded in the changer. PROG DOWN selects the previous disc loaded in the changer. SLOW Button (12) This button only functions in DVD video mode. Press this button to advance the video. If the DVD is paused, pressing this button will advance the video frame by frame. STOP Button (13) This button only functions in DVD video mode. Press this button to stop the DVD. MENU Button (14) This button only functions in DVD video mode. Press this button to select the DVD disc menu.

NEXT/PREV Buttons (2, 15) Press the up arrow or the NEXT button for the next chapter or track on the disc. Press the down arrow or PREV button to return to the beginning of the current chapter or track. Press the down arrow or PREV button twice within two seconds to return to the previous chapter or track. Each press of the NEXT/PREV button up or down will toggle through the chapters or tracks. FF/RW Buttons (3, 16) Press and hold FF (Fast Forward) once and the CD/DVD changer will begin to fast forward until the FF button is released. The RW (Reverse) button works in a similar manner. ENTER Button (17) This button only functions in DVD video mode. Use the ENTER button to enter selections from the menu screens. Use the arrow buttons to toggle through the menu screen options.

Light Button (18) Pressing this button illuminates the buttons on the re- mote control. Remote Control Battery Service † To replace the batteries for the remote control slide the

cover rearward.

The replacement batteries for the remote control are two AAA batteries. Operating Instructions — Video Screen Push up on the release button to lower the video screen.

UNDERSTANDING YOUR INSTRUMENT PANEL 239

Lowering Video Screen

240 UNDERSTANDING YOUR INSTRUMENT PANEL

1. Screen Width Button

Changes the width of the screen picture.

2. Enter Button

This button will enter the selection from the on-screen menu.

3. Brightness Button

Changes the brightness of the screen picture.

Video Screen and Controls

Operating Instructions — Headphones

Rear Headphones

1. Power Button 2. Volume Control 3. Power Indicator

UNDERSTANDING YOUR INSTRUMENT PANEL 241

Power Button Pressing the power button will turn the headphones ON/OFF. An indicator light will illuminate on the head- phone earpiece to indicate the headphones are ON. NOTE: † The headphones will turn OFF automatically in ap- proximately 3 minutes if they lose the signal form the system or when the radio or rear audio/video system is turned OFF. Volume Control Rotate the volume control to adjust the volume to the desired listening level.

242 UNDERSTANDING YOUR INSTRUMENT PANEL

Headphone Battery Service † Press the button at the bottom of each headphone

earpiece and lift the cover upward.

† Replace the battery in each earpiece and reinstall the

Headphone Battery Service

cover. The headphones require two AAA batteries.

General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. If you do not hear sound coming from the headphones, check for the following conditions: 1. Rear Seat Audio/Video System and headphones are on. Press the headphone transmitter button (1) on the remote control and the power button on the headphones. An indicator light will illuminate on the headphone earpiece to indicate the headphones are ON. 2. Weak batteries in the headphones. 3. Direct sunlight or objects blocking the line of sight between the headphone transmitter on the video screen and the headphones.

Operating Instructions — Auxiliary Input † Connect your auxiliary device (video game system, video camera, or MP3 player) cables to the color coded auxiliary jacks on the front of the DVD changer. (Refer to the illustration below). † Turn your auxiliary device on and adjust its volume to

mid or high position.

NOTE: Audio can now be heard through the vehicle’s speaker system or through the headphones (if Rear Seat Audio is turned ON). † Video will be displayed on the screen if connected to a † Your auxiliary device must be disconnected or turned

video device.

off to return to DVD changer mode.

UNDERSTANDING YOUR INSTRUMENT PANEL 243

NOTE: To operate a video game unit a DC to AC adapter may be required, plug the adapter into any power outlet.

Listed below is the standard RCA Jack/Cable connection. You may also to refer to the manufacture’s want instructions the correct colors when connecting the RCA cables.

for

1. Video in (yellow) 2. Left audio in (white) 3. Right audio in (red)

244 UNDERSTANDING YOUR INSTRUMENT PANEL

NAVIGATION SYSTEM — IF EQUIPPED The navigation system provides maps, turn identifica- tion, selection menus and instructions for selecting a variety of destinations and routes. The buttons to operate the system are located on the instrument panel next to the analog clock. Refer to your Navigation User’s Manual for detailed operating instructions. The navigation DVD unit is located in the underfloor storage compartment in the rear cargo area. A single disc containing map information for the entire United States and parts of Canada is stored in the DVD unit. Updated DVD’s are available from your authorized dealer.

Navigation DVD Location

To replace the navigation map DVD lift the storage bin cover and liner in the rear cargo area, press the eject button and the disc will eject. Gently insert the new disc into the DVD unit with the label facing up. The disc will automatically be pulled into the DVD unit.

SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satel- lite Radio. This service offers over 130 channels of music, sports, news, entertainment, and talk radio, directly from its satellites and broadcasting studios. System Activation Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of SIRIUS audio service that is included with the factory- installed satellite radio system in your vehicle. You are also invited to call Sirius to set up your free internet account so you can listen to Sirius online. For further information, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following information available when changing your subscription:

UNDERSTANDING YOUR INSTRUMENT PANEL 245

1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Your Vehicle Identification Number. Electronic Serial Number/Sirius Identification Number (ENS/SID) The Electronic Serial Number/Sirius Identification Num- ber can be accessed to retrieve the 12 digit number through each radio. To access the ESN/SID, refer to the following steps: ESN/SID Access With RBB, RAH, REVand RBK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD “EJT” button and Time buttons simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will be displayed. Press the SEEK UP (+) button to display the next four digits. Continue to press the SEEK UP (+) button until all twelve ESN/SID digits have been displayed. The SEEK

246 UNDERSTANDING YOUR INSTRUMENT PANEL

DOWN (-) will page down until the first four digits are displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. ESN/SID Access With RBP, RBU, RAZ, RB1 and RBQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID num- bers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RBB, RAH, REV and RBK Radios Press the MODE button repeatedly until 9S A9 appears in the display. A CD or tape may remain in the radio while in the Satellite radio mode.

Selecting Satellite Mode in RBP, RBU, RAZ, RB1
and RBQ Radios Press the MODE button repeatedly until the word 9SIRIUS9 appears in the display. These radios will also display the following: † After 3 seconds, the current channel name and channel † The current program type and channel number will † The current channel number will then be displayed

number will be displayed for 5 seconds.

then be displayed for 5 seconds.

until an action occurs.

A CD or tape may remain in the radio while in the Satellite radio mode.

Selecting a Channel Press and release the SEEK or TUNE buttons to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. Press and release the SCAN button (if equipped) to automatically change channels every 7 seconds. The radio will pause on each channel for 7 seconds before moving on to the next channel. The word 9SCAN9 will appear in the display between each channel change. Press the SCAN button a second time to stop the search. NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539- 7474 to discuss options for channel blocking or unblock- ing. Please have your ESN/SID information available.

UNDERSTANDING YOUR INSTRUMENT PANEL 247

Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations. Follow the memory pre-set procedures that apply to your radio. Using the PTY (Program Type) Button (If Equipped) Follow the PTY button instructions that apply to your radio. PTY Button (SCAN( When the desired program type is obtained, press the 9SCAN9 button within five seconds. The radio will play 7
seconds of the selected channel before moving to the next channel of the selected program type. Press the 9SCAN9
button a second time to stop the search.

248 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE: Pressing the 9SEEK9 or 9SCAN9 button while performing a music type scan will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button (SEEK( When the desired program is obtained, press the 9SEEK9
button within five seconds. The channel will change to the next channel that matches the program type selected. Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location or strap items to the trunk lid around the trunk lid antenna (if equipped). Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger lug- gage items such as bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna.

structure or under a physical obstacle.

Reception Quality Satellite reception may be interrupted due to one of the following reasons. † The vehicle is parked in an underground parking † Dense tree coverage may interrupt reception in the † Driving under wide bridges or along tall buildings can † Placing objects over or too close to the antenna can

cause intermittent reception.

form of short audio mutes.

cause signal blockage.

REMOTE SOUND SYSTEM CONTROLS The remote sound system controls are located on the rear surface of the steering wheel at the 3 and 9 o’clock positions. The right hand rocker switch has a push button in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume and pressing the bottom of the rocker switch will decrease the volume. Pressing the center button changes the operation of the radio from AM to FM to Tape or CD mode depending on which radio is in the vehicle. The left hand rocker switch has a push button in the center. The function of the left hand switch is different depending on which mode you are in. The following describes the left hand rocker switch operation in each mode:

UNDERSTANDING YOUR INSTRUMENT PANEL 249

Radio Operation Pressing the top of the switch will SEEK up for the next listenable station and pressing the bottom of the switch will SEEK down for the next listenable station. The button located in the center of the left hand switch will tune to the next pre-set station that you have programmed in the radio pre-set push-button. CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play. If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch has no function in this mode.

250 UNDERSTANDING YOUR INSTRUMENT PANEL

CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high.

RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio. If your radio performance does not satisfactorily “clear” by the repositioning of the antenna, it is recommended that the radio volume be turned down or off during cellular phone operation.

CLIMATE CONTROLS The Air Conditioning and Heating System is designed to make you comfortable in all types of weather.

Manual Air Conditioning and Heating System

UNDERSTANDING YOUR INSTRUMENT PANEL 251

second time the indicator light turns off, the blower will turn off and the system will be positioned in the recircu- lation mode. Blower Control

The Blower controls the amount of air delivered to the passenger compartment. There are four blower speeds.

The fan speed increases as you move the control clockwise.

Manual Heating and A/C Controls

Power Button When the “POWER” button is pressed the indicator will illuminate and the blower will run at the speed selected by the front blower control. When the button is pressed a

252 UNDERSTANDING YOUR INSTRUMENT PANEL

Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the tem- perature of air coming from the outlets on their side of the vehicle.

Mode Control

The mode control allows you to choose from several patterns of air distribution.

NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots.

Dual Zone Temperature Control

This is accomplished by having a separate temperature control lever for both the driver and front seat passenger. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.

UNDERSTANDING YOUR INSTRUMENT PANEL 253

Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center outlets. The thumbwheel next to the outboard outlets can be rotated to regulate or shut off the air flow from these outlets.

Panel Mode

Panel Outlets

254 UNDERSTANDING YOUR INSTRUMENT PANEL

Bi-Level Mode

Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. In many temperature lever positions, the bi- NOTE: level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.

Bi-Level Outlets

Floor Mode

Mix Mode

UNDERSTANDING YOUR INSTRUMENT PANEL 255

Floor Outlets

Mix Outlets

Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.

Air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while keep- ing the windshield clear.

256 UNDERSTANDING YOUR INSTRUMENT PANEL

Defrost Mode

Defrost Outlets

Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows.

NOTE: For improved safety, the compressor is activated and the recirculation mode is deactivated when Mix or Defrost modes are selected. This is done to assist in drying the air and it will help in keeping the windows from fogging. Manual Air Conditioning Operation

To turn on the air conditioning, set the front blower control to any speed and press the A/C button which is located next to the recirculation button. An indicator light on the A/C button shows that the air conditioning is on. NOTE: The indicator light in the “POWER” button must be on for the climate control system to operate. Cool dehumidified air comes through the outlets selected by the Mode Control. To turn off the air conditioning, press the A/C button a second time. The indicator light will turn off.

been running for a few seconds.

NOTE: † The compressor will not engage until the engine has † If your air conditioning performance seems lower than expected, check the A/C air filter (ATC equipped vehicles only) and the front of the A/C condenser for an accumulation of dirt or insects. The A/C condenser is located in front of the radiator. The A/C air filter is located under the instrument panel on the passenger side. † Fabric type fascia protectors tend to block the amount of air to the condenser and may reduce air condition- ing performance.

Economy Mode If economy mode is desired, press the A/C button to turn off the indicator light, and the A/C compressor. Move the temperature control lever to the desired temperature.

UNDERSTANDING YOUR INSTRUMENT PANEL 257

Recirculation Control

Press the recirculation button to recirculate the air inside the vehicle. This is located next to the A/C button. An indicator light on the button shows that air is being recirculated. Use the recirculation mode to rapidly cool the inside of the vehicle. The recirculation mode can also be used to temporarily block out outside odors, smoke, and dust. NOTE: † When the ignition switch is turned OFF, the recircula- † In cold weather, use of the Recirculation mode may lead to excessive window fogging. The Recirculation mode is not allowed in the Mix and Defrost modes to improve window clearing operation. Recirculation will be disabled automatically if these modes are selected.

tion feature will be cancelled.

258 UNDERSTANDING YOUR INSTRUMENT PANEL

† If the recirculation button is pressed while in the Mix or Defrost mode, the indicator light in the recirculation button will flash 3 times indicating that recirculation is not allowed.

A/C Recirculation Programming The recirculation control is programmed to cancel the recirculation mode when the ignition key is turned OFF and will reset to outside air mode when the ignition key is turned ON. The frequent use of outside air will help keep odors from building up within the air conditioner- heater housing. It is recommended that the recirculation mode be used as little as possible, especially in humid climates. For hot and dry climates, or people who are allergic to pollen and find frequent use of the recirculation mode necessary, the recirculation mode can be programmed to not automatically reset to the outside mode by using the following procedures:

† Turn the ignition switch to the OFF position. † Set the mode control to “PANEL”. † Depress and hold in the “POWER” button. † Start the engine, and continue to hold in the “POWER” button until the indicator light starts flashing repeat- edly. † Press the recirculation button until the indicator light † The selection will be stored when the ignition switch is

remains lit.

turned OFF or if the “POWER” button is pressed.

If the recirculation indicator light is lit, the recirculation mode will not reset when the engine is started. If the recirculation indicator light is not lit, the recirculation mode will reset to the outside air mode when the engine is started. The programmed status can be changed back and forth by following the above mentioned procedure.

Dual-Zone Automatic Temperature Control The Dual Zone Automatic Temperature Control (ATC) System automatically maintains the interior comfort level desired by the driver and front seat passenger. This is accomplished by using two infrared sensors located in the center of the instrument panel. The two infrared sensors independently measure the surface temperature of the driver and front seat passenger. Based on the sensor input, the system automatically adjusts the air temperature, the airflow volume, the airflow distribu- tion, and amount of inside air recirculation to maintain front seat occupant comfort, even under changing out- side weather conditions.

UNDERSTANDING YOUR INSTRUMENT PANEL 259

Dual-Zone Automatic Temperature Control

To operate the system, press either the 9AUTO HI9 or 9AUTO LO9 buttons. The system now automatically regulates the heating and air conditioning system includ- ing blower speed, outlet air temperature, and airflow distribution through the various outlets within the in- strument panel. Using the 9TEMP9 buttons, adjust the

260 UNDERSTANDING YOUR INSTRUMENT PANEL

temperature you would like the system to maintain. When the system is set to your comfort level, it is not necessary to change the settings. You will experience the greatest efficiency by allowing the system to function automatically. The system will operate fully automati- cally in either 9AUTO HI9 or 9AUTO LO9. The 9AUTO LO9 setting will limit the maximum fan speed and should be used when more quiet operation is desired. Use the 9AUTO HI9 setting when the quickest cool-down or warm-up performance is desired. NOTE: † It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to provide comfort as quickly as possible. † The temperature can be displayed in U.S. or Metric by selecting the US/M customer programmable feature.

Refer to the “Electronic Vehicle Information Center- Customer Programmable Features” in Section 3 of this manual.

To provide you with maximum comfort in the automatic mode, during cold start-ups the blower fan will remain off and “DELAY” will appear in the display until the engine warms up. An estimate of the time remaining until the “DELAY” is complete will appear periodically in the display. However, the fan will engage immediately if the defrost mode is selected or by pushing the blower switch and manually adjusting the fan speed. This feature may be disabled using the following proce- dure: † Press and hold the Heated Rear Window and Auto LO † The “DELAY” symbol will flash to indicate that the

buttons for 5 seconds.

feature as been disabled.

This feature may be enabled using the following proce- dure: † Press and hold the Heated Rear Window and Auto HI † The “DELAY” symbol will flash to indicate that the

buttons for 5 seconds.

feature as been enabled.

Power Button This button turns the entire system ON/OFF. When the system is turned on it will return to the previous settings. Dual/Single Zone Operation When 9DUAL9 is displayed in the ATC control unit, the driver and passenger air outlet temperatures can be individually adjusted from the two independent 9TEMP9
buttons. When a front seat passenger is not present, pressing the 9DUAL9 button will match the passenger’s temperature setting to the driver’s temperature setting. This will help equalize air outlet temperatures across the

UNDERSTANDING YOUR INSTRUMENT PANEL 261

left and right side of the instrument panel. The outside temperature will replace the passenger’s temperature setting in the display. Pressing the 9DUAL9 button a second time or adjusting the passenger’s 9TEMP9 button will return the system to dual independent temperature operation. Manual Operation This system offers a full complement of manual override features. The indicator light in both the 9AUTO HI9 or 9AUTO LO9 buttons will turn off when the system is being used in the manual mode. The fan speed, airflow distribution, and outside air/recirculated air can be manually adjusted. NOTE: Each of these features operate independently from each other. If any one feature is controlled manually, the remaining features will continue to operate automati- cally.

262 UNDERSTANDING YOUR INSTRUMENT PANEL

The front blower control can be set to any fixed blower speed by pressing the rocker switch up or down. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode. The fan will now operate at a fixed speed until additional speeds are selected or until either the 9AUTO HI9 or 9AUTO LO9 buttons are pressed. The system will continue to automatically adjust air temperature and airflow distribution. The operator can also select the direction of the air by pressing the mode control rocker switch located to the left of the A/C button and selecting one of the following positions. Panel Mode

Panel Outlets

Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the knob up, down, left, or right will direct the air accordingly. The thumbwheel next to each outlet can be rotated to reduce or shut off the air flow from these outlets.

UNDERSTANDING YOUR INSTRUMENT PANEL 263

Air comes from both the instrument panel outlets and floor outlets. A slight amount of air is also directed through the defrost and side window demister outlets. In many temperature positions, the bi-level NOTE: mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.

Bi-Level Mode

Bi-Level Outlets

264 UNDERSTANDING YOUR INSTRUMENT PANEL

Floor Mode

Mix Mode

Floor Outlets

Mix Outlets

Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.

Air comes from the floor, defrost and side window demist outlets. This mode is not used when operating in either 9AUTO HI9 or 9AUTO LO9. This mode should be used when airflow to the floor and windshield is desired.

Defrost Mode

Defrost Outlets

Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows. If a fog or mist on the

UNDERSTANDING YOUR INSTRUMENT PANEL 265

windshield or side glass starts to impair visibility, press the front blower button and increase the fan speed to maximum. NOTE: While operating in 9AUTO HI9 or 9AUTO LO9, the system will not automatically sense the presence fog, mist, or ice on the windshield. The defrost button must be pressed to clear the windshield and side glass.

Depress the “A/C” button to turn on and off the air conditioning during manual operation only. Cool dehumidified air comes through the outlets selected by the Mode Control. To turn off the air condi- tioning, press the A/C button a second time. The A/C symbol in the display will turn off. If a fog or mist appears on the windshield or NOTE: side glass, press the “A/C” button to engage the com- pressor or press the defrost button. If a fog or mist on the

266 UNDERSTANDING YOUR INSTRUMENT PANEL

windshield or side glass starts to impair visibility, press the front blower button and increase the fan speed to maximum. Recirculation Control

When the outside air contains smoke, odors, high humidity, or if rapid cooling is desired you may wish to recirculate interior air by pressing the recirculation button. The recircu- lation mode should only be used temporarily. The recir- culate symbol will illuminate in the display when this button is selected. Push the button a second time to allow outside air into the vehicle. In cold weather, use of the recirculation mode NOTE: may lead to excessive window fogging. The recirculation mode is not allowed in the Mix and Defrost modes to improve window clearing operation. Recirculation will be disabled automatically if these modes are selected.

A/C Recirculation Programming The recirculation control is programmed to cancel the recirculation mode when the ignition key is turned OFF and will reset to the outside air mode when the ignition key is turned “ON”. The frequent use of outside air will help keep odors from building up within the air conditioner-heater housing. It is recommended that the recirculation mode be used as little as possible, especially in humid climates. For hot and dry climates, or people who are allergic to pollen and find frequent use of the recirculation mode necessary, the recirculation mode can be programmed to not automatically reset to the outside mode by using the following procedures: † Turn the ignition switch to the OFF position. † Press and hold the recirculation button.

† While holding the recirculation button, turn the igni- † Continue holding the recirculation button for 4 sec-

tion switch to the “RUN” position.

onds, then release.

The recirculation control is now programmed so that the recirculation mode will not reset to the outside air mode when the engine is restarted. The recirculation program- ming can be changed back by repeating this procedure. Rear Blower Operation To operate the rear fan, press the 9REAR9 button. The first time this button is pressed the 9REAR AUTO9 display will illuminate indicating that the rear fan speed is automatically controlled. To manually control the rear fan speed, press the 9REAR9 button again and only 9REAR9 will illuminate in the display. This allows the rear seat occupants to control the rear fan speed using the

UNDERSTANDING YOUR INSTRUMENT PANEL 267

switch located in the center console between the second row seats. By pressing the 9REAR9 button a third time, the rear fan will shut off. When the ATC display reads 9REAR AUTO9 or when the rear fan is off, the switch located in the center console between the second row seats is not functional. When the ATC display reads 9REAR9, only the rear seat occupants can control the rear fan speed from the rear switch. When in the “REAR” mode, the rear occupants can set the rear switch to any fan speed including 9OFF9, or 9AUTO9. While in the 9AUTO9 position, the rear fan speed will be automatically controlled. Summer Operation The engine cooling system in air conditioned vehicles must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating. A 50% solution of ethylene

268 UNDERSTANDING YOUR INSTRUMENT PANEL

glycol antifreeze coolant in water is recommended. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection. Winter Operation To insure the best possible heater and defroster perfor- mance, make sure the engine cooling system is function- ing properly and the proper amount, type, and concen- tration of coolant is used. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection. Use of the air Recirculation mode during winter months is not recommended because it may cause window fogging. Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air condi- tioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate

system lubrication to minimize the possibility of com- pressor damage when the system is started again. Window Fogging Vehicle windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C button to reduce the humidity inside the vehicle. Fogging on the inside of the windshield can be quickly removed by pressing the defrost button and increasing the blower speed. Do not use the Recirculation mode without the A/C button for long periods as fogging may occur. Outside Air Intake Before driving, always make sure the air intake located directly in front of the windshield is free of obstructions such as leaves, ice, or snow, which could reduce airflow and/or plug the water drain tube inside the plenum.

A/C Air Filter — If Equipped On vehicles equipped with Automatic Temperature Con- trol (ATC), the climate control system filters out dust and pollen from the air. Refer to section 7 “Air Conditioning” for filter replacement instructions. Outside Temperature Display The outside temperature can be shown in the ATC display by pressing the 9OUTSIDE TEMP9 button. After pressing this button, the front seat passenger’s tempera- ture setting display will be replaced with the current outside temperature. Press the 9OUTSIDE TEMP9 button again or press the passenger’s 9TEMP9 button to return the display to the passenger’s temperature setting.

UNDERSTANDING YOUR INSTRUMENT PANEL 269

Electric Rear Window Defroster

Press this button to turn on the rear window defroster and the heated side mirrors. A light in the button will illuminate to indicate the rear window defroster is ON. The defroster automatically turns off after about 10 minutes of operation.

CAUTION!

To avoid damaging the electrical conductors of the rear window defroster, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. Labels can be peeled off after soaking with warm water.

STARTING AND OPERATING

CONTENTS

m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 275
N Automatic Transmission . . . . . . . . . . . . . . . . 276
N Normal Starting (Above 32°F / 0°C) . . . . . . . . 276
N Extremely Cold Weather Starting (Below 220°F /

–29°C)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276

N High Altitude Starting (Above 4,000 Ft. /

1 219 m) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
N If Engine Fails To Start . . . . . . . . . . . . . . . . . 277
N After Starting . . . . . . . . . . . . . . . . . . . . . . . . 278
m Engine Block Heater — If Equipped . . . . . . . . . 278

m Automatic Transmission . . . . . . . . . . . . . . . . . . 278
N Brake/Transmission Interlock System . . . . . . . 279