2004 Chevrolet Suburban Owners Manual

Download PDF Manual
Additional windshield breakage may also occur from the right front passenger air bag. (cid:127) Air bags are designed to inﬂate only once. After an air bag inﬂates, you’ll need some new parts for your air bag system. If you don’t get them, the air bag system won’t be there to help protect you in another crash. A new system will include air bag modules and possibly other parts. The service manual for your vehicle covers the need to replace other parts. (cid:127) Your vehicle is equipped with electronic frontal sensors which help the sensing system distinguish between a moderate and a more severe frontal impact. Your vehicle is also equipped with a crash sensing and diagnostic module, which records information about the frontal air bag system. The module records information about the readiness of the system and when the system commands air bag inﬂation. It records the status of the driver’s safety belt usage in a crash in which the air bag deploys or a crash in which the air bag nearly deploys. The module also records speed, engine rpm, brake and throttle data. 1-81 (cid:127) Passenger Sensing System If your rearview mirror has one of the indicators pictured in the following illustrations, your vehicle has a passenger sensing system. The indicator will be visible when you turn your ignition key to START or RUN. The words ON and OFF or the symbol for on and off, will be visible on the rearview mirror during the system check. When the system check is complete, either the word ON or the word OFF, or the symbol for on or the symbol for off will be visible. See Passenger Air Bag Status Indicator on page 3-42. If your rearview mirror does not have either of the indicators pictured, then your vehicle does not have the passenger sensing system. Passenger Air Bag Status Indicator – United States The passenger sensing system will turn off the right front passenger’s frontal air bag under certain conditions. The driver’s air bag and the side air bags are not part of the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger’s seat and safety belt. The sensors are designed to detect the presence of a properly-seated occupant and determine if the passenger’s frontal air bag should be enabled (may inﬂate) or not. Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. General Motors recommends that child restraints be secured in a rear seat, including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat. Passenger Air Bag Status Indicator – Canada 1-82 Your vehicle has a rear seat that will accommodate a rear-facing child restraint. A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the air bag deploys. {CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s air bag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating air bag. Even though the passenger sensing system is designed to turn off the passenger’s frontal air bag if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an air bag will not deploy under some unusual circumstance, even though it is turned off. General Motors recommends that rear-facing child restraints be secured in the rear seat, even if the air bag is off. The passenger sensing system is designed to turn off the right front passenger’s frontal air bag if: the right front passenger seat is unoccupied the system determines that an infant is present in a rear-facing infant seat the system determines that a small child is present in a forward-facing child restraint the system determines that a small child is present in a booster seat a right front passenger takes his/her weight off of the seat for a period of time the right front passenger seat is occupied by a smaller person, such as a child who has outgrown child restraints or if there is a critical problem with the air bag system or the passenger sensing system. When the passenger sensing system has turned off the passenger’s frontal air bag, the off indicator will light and stay lit to remind you that the air bag is off. If a child restraint has been installed and the on indicator is lit, turn the vehicle off. Remove the child restraint from the vehicle and reinstall the child restraint following the child restraint manufacturer’s directions and refer to Securing a Child Restraint in the Right Front Seat Position on page 1-68. 1-83 (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) If a person of adult-size is sitting in the right front passenger’s seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, turn the vehicle off and ask the person to place the seatback in the fully upright position, then sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended. Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and then enable the passenger’s air bag. If after reinstalling the child restraint and restarting the vehicle, the on indicator is still lit, check to make sure that the vehicle’s seatback is not pressing the child restraint into the seat cushion. If this happens, slightly recline the vehicle’s seatback and adjust the seat cushion if possible. Also make sure the child restraint is not trapped under the vehicle head restraint. If this happens, adjust the head restraint. If the on indicator is still lit, secure the child in the child restraint in a rear seat position in the vehicle and check with your dealer. The passenger sensing system is designed to enable (may inﬂate) the right front passenger’s frontal air bag anytime the system senses that a person of adult size is sitting properly in the right front passenger’s seat. When the passenger sensing system has allowed the air bag to be enabled, the on indicator will light and stay lit to remind you that the air bag is active. For some children who have outgrown child restraints and for very small adults, the passenger sensing system may or may not turn off the right front passenger’s frontal air bag, depending upon the person’s seating posture and body build. Everyone in your vehicle who has outgrown child restraints should wear a safety belt properly — whether or not there is an air bag for that person. 1-84 {CAUTION: If the air bag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the air bag system. If this ever happens, have the vehicle serviced promptly, because anadult-size person sitting in the right front passenger’s seat may not have the protection of the frontal air bag. See “Air Bag Readiness Light” in the Index for more on this, including important safety information. Aftermarket equipment, such as seat covers, can affect how well the passenger sensing system operates. You may want to consider not using seat covers or other aftermarket equipment if your vehicle has the passenger sensing system. See Adding Equipment to Your Air Bag-Equipped Vehicle on page 1-86 for more information about modiﬁcations that can affect how the system operates. {CAUTION: Stowing of articles under the passenger’s seat or between the passenger’s seat cushion and seatback may interfere with the proper operation of the passenger sensing system. 1-85 Adding Equipment to Your Air Bag-Equipped Vehicle Q: Is there anything I might add to the front or sides of the vehicle that could keep the air bags from working properly? A: Yes. If you add things that change your vehicle’s frame, bumper system, front end or side sheet metal or height, they may keep the air bag system from working properly. Also, the air bag system may not work properly if you relocate any of the air bag sensors. If you have any questions about this, you should contact Customer Assistance before you modify your vehicle. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual. See Customer Satisfaction Procedure on page 7-2. Servicing Your Air Bag-Equipped Vehicle Air bags affect how your vehicle should be serviced. There air bag system parts in several places around your vehicle. You don’t want the system to inﬂate while someone is working on your vehicle. Your dealer and the service manual have information about servicing your vehicle and the air bag system. To purchase a service manual, see Service Publications Ordering Information on page 7-11. {CAUTION: For up to 10 seconds after the ignition key is turned off and the battery is disconnected, an air bag can still inﬂate during improper service. You can be injured if you are close to an air bag when it inﬂates. Avoid yellow connectors. They are probably part of the air bag system. Be sure to follow proper service procedures, and make sure the person performing work for you is qualiﬁed to do so. Air bag systems do not need regular maintenance. 1-86 Q: Because I have a disability, I have to get my vehicle modiﬁed. How can I ﬁnd out whether this will affect my advanced air bag system? A: Changing or moving any parts of the front seats, safety belts, the air bag sensing and diagnostic module (located under the driver’s seat), or the inside rearview mirror can affect the operation of the advanced air bag system. If you have questions, call Customer Assistance. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual. See Customer Satisfaction Procedure on page 7-2. Restraint System Check Checking Your Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Torn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away. Also look for any opened or broken air bag covers, and have them repaired or replaced. (The air bag system does not need regular maintenance.) 1-87 Replacing Restraint System Parts After a Crash {CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible. If you’ve had a crash, do you need new belts or LATCH system parts? After a very minor collision, nothing may be necessary. But if the belts were stretched, as they would be if worn during a more severe crash, then you need new parts. If the LATCH system was being used during a more severe crash, you may need new LATCH system parts. If belts are cut or damaged, replace them. Collision damage also may mean you will need to have LATCH system, safety belt or seat parts repaired or replaced. New parts and repairs may be necessary even if the belt or LATCH system wasn’t being used at the time of the collision. If an air bag inﬂates, you’ll need to replace air bag system parts. See the part on the air bag system earlier in this section. 1-88 Section 2 Features and Controls Keys ...............................................................2-3 Remote Keyless Entry System .........................2-4 Remote Keyless Entry System Operation ...........2-5 Doors and Locks .............................................2-8 Door Locks ....................................................2-8 Power Door Locks ..........................................2-9 Delayed Locking ...........................................2-10 Programmable Automatic Door Locks ..............2-10 Rear Door Security Locks ..............................2-12 Lockout Protection ........................................2-13 Liftgate ........................................................2-13 Windows ........................................................2-15 Manual Windows ..........................................2-16 Power Windows ............................................2-16 Sun Visors ...................................................2-17 Theft-Deterrent Systems ..................................2-18 Content Theft-Deterrent .................................2-18 Passlock® ....................................................2-20 Starting and Operating Your Vehicle ................2-20 New Vehicle Break-In ....................................2-20 Ignition Positions ..........................................2-21 Starting Your Engine .....................................2-22 Adjustable Throttle and Brake Pedal ................2-23 Engine Coolant Heater ..................................2-23 Automatic Transmission Operation ...................2-25 Four-Wheel Drive ..........................................2-28 All-Wheel Drive with Stabilitrak® ......................2-33 Parking Brake ..............................................2-36 Shifting Into Park (P) .....................................2-37 Shifting Out of Park (P) .................................2-39 Parking Over Things That Burn .......................2-40 Engine Exhaust ............................................2-40 Running Your Engine While You Are Parked .......2-41 Mirrors ...........................................................2-42 Manual Rearview Mirror .................................2-42 Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display ....................................................2-42 Automatic Dimming Rearview Mirror with Compass and Temperature Display ..............2-44 Outside Manual Mirrors ..................................2-47 Outside Camper-Type Mirrors .........................2-47 Outside Power Mirrors ...................................2-48 Outside Power Camper-Type Mirror .................2-48 Outside Power Foldaway Mirrors .....................2-48 2-1 Section 2 Features and Controls Outside Automatic Dimming Mirror ..................2-49 Outside Curb View Assist Mirrors ....................2-50 Outside Convex Mirror ...................................2-50 Outside Heated Mirrors ..................................2-50 OnStar® System .............................................2-51 HomeLink® Transmitter ...................................2-53 Programming the HomeLink® Transmitter .........2-53 Storage Areas ................................................2-57 Glove Box ...................................................2-57 Cupholder(s) ................................................2-57 Front Storage Area .......................................2-57 Center Console Storage Area .........................2-57 Luggage Carrier ...........................................2-57 Rear Storage Area ........................................2-59 Convenience Net ..........................................2-59 Cargo Cover ................................................2-59 Sunroof .........................................................2-60 Vehicle Personalization ...................................2-61 Memory Seat ...............................................2-61 2-2 Keys {CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children. 2-3 Remote Keyless Entry System If equipped, the keyless entry system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference received, including interference that may cause undesired operation of the device. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Your vehicle has one double-sided key for the ignition and all door locks as well as the spare tire hoist lock, if equipped. If you ever lock your keys in your vehicle, If you ever lose your keys, your dealer will be able to assist you with obtaining replacements. Notice: you may have to damage the vehicle to get in. Be sure you have spare keys. If you ever do get locked out of your vehicle, call the GM Roadside Assistance Center. See Roadside Assistance Program on page 7-6. If your vehicle is equipped with the OnStar® system with an active subscription and you lock your keys inside the vehicle, OnStar® may be able to send a command to unlock your vehicle. See OnStar® System on page 2-51 for more information. 2-4 At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: (cid:127) Check the distance. You may be too far from your vehicle. You may need to stand closer during rainy or snowy weather. (cid:127) Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again. (cid:127) Check to determine if battery replacement is necessary. See “Battery Replacement” under Remote Keyless Entry System Operation on page 2-5. If you are still having trouble, see your dealer or a qualiﬁed technician for service. Remote Keyless Entry System Operation If your vehicle has this feature, you can lock and unlock your doors from about 3 feet (1 m) up to 30 feet (9 m) away using the remote keyless entry transmitter supplied with your vehicle. UNLOCK: Pressing this button once will unlock the driver’s door. The parking lamps will ﬂash and the interior lights will come on. The ground illumination lamps will come on. Pressing UNLOCK again within three seconds will cause the remaining doors to unlock. The parking lamps will ﬂash and the interior lights will come on. LOCK: Pressing this button once will lock all of the doors. Wait one second, then press LOCK again and the horn will chirp. Operating the keyless entry transmitter may interact with the theft-deterrent system. See Content Theft-Deterrent on page 2-18. 2-5 (cid:127) Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about two years. You can tell the battery is weak if the transmitter won’t work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it’s probably time to change the battery. Notice: When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter. Remote Alarm When the panic button with the horn symbol on the keyless entry transmitter is pressed, the horn will sound and the headlamps and taillamps will ﬂash for up to 30 seconds. This can be turned off by pressing the panic button again, waiting for 30 seconds, or starting the vehicle. Matching Transmitter(s) to Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer. When the dealer matches the replacement transmitter to your vehicle, any remaining transmitters must also be matched. Once your dealer has coded the new transmitter, the lost transmitter will not unlock your vehicle. Each vehicle can have a maximum of four transmitters matched to it. 2-6 To replace the battery in the keyless entry transmitter do the following: Resynchronization Resynchronization may be necessary due to the security method used by this system. The transmitter does not send the same signal twice to the receiver. The receiver will not respond to a signal that has been sent previously. This prevents anyone from recording and playing back the signal from the transmitter. To resynchronize your transmitter, stand close to your vehicle and press and hold the LOCK and UNLOCK buttons on the transmitter at the same time for 15 seconds. The door locks should cycle to conﬁrm synchronization. If the locks do not cycle, see your dealer for service. 1. Insert a dime, or similar object, in the slot between the covers of the transmitter housing near the key ring hole. Remove the bottom by twisting the dime. 2. Remove and replace the battery with a three-volt CR2032 or equivalent battery, positive (+) side up. 3. Align the covers and snap them together. 4. Resynchronize the transmitter. 5. Check the operation of the transmitter. 2-7 There are several ways to lock and unlock your vehicle. You can use the keyless entry system, if equipped, or you can also use your key. To lock the door from the inside, slide the lever rearward. To unlock the door, slide the lever forward. Doors and Locks Door Locks {CAUTION: Unlocked doors can be dangerous. (cid:127) Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive. (cid:127) Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it. (cid:127) Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. 2-8 Power Door Locks If your vehicle is equipped with power door locks, press the raised side of the switch, with the lock symbol, on either front door to lock all the doors at once. If your vehicle has this power door lock switch, press the bottom of the switch on either front door to lock all the doors at once. Press the recessed side of the switch with the unlock symbol, to unlock all the doors at once. If your vehicle has the delayed locking feature, see “Delayed Locking” later in this section. Press the top of the switch to unlock all the doors at once. The power door locks will operate at any time even when the ignition is off. Operating the power locks may interact with the theft-deterrent system (if equipped). See Content Theft-Deterrent on page 2-18. 2-9 Delayed Locking When locking the doors with the power lock switch or the keyless entry transmitter and a door or the liftgate (if equipped) is open, the delayed locking feature will delay locking the doors until ﬁve seconds after the last door is closed. You will hear three chimes to signal that the delayed locking feature is in use. Pressing the power lock switch or the lock button on the keyless entry transmitter twice will override the delayed locking feature and immediately lock all the doors. You can turn the delayed locking feature off or back on again by doing the following: 1. Press and hold the power door lock switch in the lock position. 2. Press unlock twice on the remote keyless entry transmitter. This feature will not operate if the key is in the ignition. You can also program this feature using the DIC. See “Delayed Locking” under DIC Operation and Displays on page 3-56. Programmable Automatic Door Locks Your vehicle is equipped with an automatic lock/unlock feature which enables you to program your vehicle’s power door locks. You can program this feature through the Driver Information Center (DIC), or by the following method. Programmable Locking Feature The following is the list of available programming options: Mode 1: All doors lock when the transmission is shifted into gear. Mode 2: All doors lock when the vehicle speed is greater than 8 mph (13 km/h). Mode 3: No automatic door locking. The automatic door locks were pre-programmed at the factory to lock all the doors when the transmission is shifted into gear. The following instructions detail how to program your door locks differently than the factory setting. Choose one of the three programming options listed above before entering the program mode. 2-10 Programmable Unlocking Feature The following is the list of available programming options: Mode 1: Driver’s door unlocks when the transmission is shifted into PARK (P). Mode 2: All doors unlock when the transmission is shifted into PARK (P). Mode 3: All doors unlock when the key is removed from the ignition. Mode 4: No automatic door unlock. The automatic door locks were pre-programmed at the factory to unlock the driver’s door once the transmission is shifted to PARK (P). The following instructions detail how to program your door locks differently than the factory setting. Choose one of the four programming options listed above before entering the program mode. To enter the program mode, do the following: 1. Begin with the ignition off. Then pull the turn signal/multifunction lever toward you and hold it there while you perform the next step. 2. Turn the key to RUN and LOCK twice. Then, with the key in LOCK, release the turn signal/multifunction lever. Once you do this, you will hear the lock switch lock and unlock, the horn will chirp twice, and a 30 second program timer will begin. You are now ready to program the automatic door locks. 3. Select one of the three programming options listed previously, and press the lock side of the power door lock switch to cycle through the lock options. You will have 30 seconds to begin programming. If you exceed the 30 second limit, the locks will automatically lock and unlock and the horn will chirp twice to indicate that you have left the program mode. If this occurs, repeat the procedure beginning with Step 1 to re-enter the programming mode. You can exit the program mode any time by turning the ignition to RUN (the locks will automatically lock and unlock and the horn will chirp twice to indicate that you are leaving the program mode). If the lock/unlock switches are not pressed while in the programming mode, the current auto lock/unlock setting will not be modiﬁed. See your dealer for more information. 2-11 To enter the program mode, do the following: 1. Begin with the ignition off. Then pull the turn signal/multifunction lever toward you and hold it there while you perform the next step. 2. Turn the key to RUN and LOCK twice. Then, with the key in LOCK, release the turn signal/multifunction lever. Once you do this, you will hear the lock switch lock and unlock, the horn will chirp twice, and a 30-second program timer will begin. 3. You are now ready to program the automatic door locks. Select one of the four programming options listed previously, and press the unlock side of the power door lock switch to cycle through the unlocking options. You will have 30 seconds to begin programming. If you exceed the 30-second limit, the locks will automatically lock and unlock and the horn will chirp twice to indicate that you have left the program mode. If this occurs, repeat the procedure beginning with Step 1 to re-enter the programming mode. You can exit the program mode any time by turning the ignition to RUN. The locks will automatically lock and unlock and the horn will chirp twice to indicate that you are leaving the program mode. If the lock/unlock switches are not pressed while in the programming mode, the current auto lock/unlock setting will not be modiﬁed. See your dealer for more information. 2-12 Rear Door Security Locks If your vehicle is equipped with this feature, you can lock the rear side doors so they cannot be opened from the inside by passengers. This feature is located on the inside edge of the rear doors. To use one of the locks do the following: 1. Open one of the rear doors. 2. To engage the rear door security locks, move the lever forward. 3. To disengage the lock, move the lever rearward. 4. Close the door. 5. Do the same thing to the other rear door. The rear doors of your vehicle cannot be opened from the inside when this feature is in use. If you want to open the rear door while the security lock is engaged, unlock the door and open the door from the outside. Lockout Protection This feature protects you from locking your key in the vehicle when the key is in the ignition and a door is open. If the power lock switch is pressed when a door is open and the key is in the ignition, all of the doors will lock and then the driver’s door will unlock. Liftgate {CAUTION: It can be dangerous to drive with the liftgate glass, liftgate or rear doors open because carbon monoxide (CO) gas can come into your vehicle. You can not see or smell CO. It can cause unconsciousness and even death. If you must drive with the liftgate glass, liftgate or rear doors open or if electrical wiring or other cable connections must pass through the seal between the body and the liftgate glass, liftgate or rear doors: (cid:127) Make sure all other windows are shut. (cid:127) Turn the fan on your heating or cooling system to its highest speed with the setting on VENT or OUTSIDE AIR. That will force outside air into your vehicle. See Climate Control System on page 3-22. If you have air outlets on or under the instrument panel, open them all the way. See Engine Exhaust on page 2-40. 2-13 (cid:127) Liftgate Glass and Liftgate To open a mechanical lock system from the outside, insert the key into the lock and turn it counterclockwise to unlock the glass and liftgate. The liftgate glass can be opened using the button on the liftgate after the doors have been unlocked. This can be done by using either the power door locks or the remote keyless entry system. To open the entire liftgate, lift the handle located in the center of the door. To lock a power lock system from the outside, insert the key into the lock button and turn clockwise. All doors will lock. You may also use the keyless entry system or the power door locks to lock the liftgate and liftgate glass. Panel Doors To open the rear panel doors, you must open the passenger’s side panel door ﬁrst. If the door is locked, insert your door key in the lock and turn it counterclockwise to unlock it. To open the passenger’s side panel door, pull on the handle and pull the door open. To open the driver’s side panel door, ﬁrst open the passenger’s side door. Then, pull the handle on the left door edge out and pull the door open. To close the doors, close the driver’s side door ﬁrst. After securely closing the door, close the passenger’s side door. Make sure both doors are latched securely. To lock the rear doors from outside the vehicle, put your key in the lock and turn it clockwise. If you have power door locks, you can lock the side doors as well as the rear doors from inside the vehicle. For more information, see Power Door Locks on page 2-9 earlier in this section. 2-14 Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 2-15 Manual Windows Turn the hand crank on each door to manually raise or lower the manual windows. Power Windows If you have power windows, the controls are located on each of the side doors. The driver’s door has a switch for the passenger’s windows as well. Your power windows will work when the ignition has been turned to ACCESSORY or RUN or when Retained Accessory Power (RAP) is active. See Ignition Positions on page 2-21. (cid:127) Pull up the front edge of the switch to raise the window. (cid:127) Press the front edge of the switch to lower the window. Express-Down Windows The driver and front passenger windows have an express down feature that allows the windows to be lowered without holding the switch. Press down on the front edge of the window switch to activate the express down mode. The express down mode can be canceled at any time by pulling up on the switch. To open the window partway, lightly tap the switch until the window is at the desired position. 2-16 Lock-Out Switch If you have power windows, the driver’s door power window switch has a lock-out feature. The lock-out switch is located in front of the power window switches. This feature prevents all passenger windows from operating, except from the driver’s position, when the lock-out switch is engaged. To engage the lock-out feature press the switch, and an indicator light will illuminate. To disengage the feature, press the switch again and the indicator light will go off. When the button is not engaged, the passenger’s power windows switches will operate. Sun Visors To block out glare, you can swing down the top and bottom visors (if equipped). You can also swing the bottom visor from side-to-side. Your visors may have an extension that can be pulled out for additional glare protection. Lighted Visor Vanity Mirror If equipped, pull the sun visor down and lift the mirror cover to turn on the lamps. There is a slide switch to adjust the brightness of the lamps. 2-17 Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. However, there are ways you can help. Content Theft-Deterrent Your vehicle may be equipped with a content theft-deterrent alarm system. With this system, the security light will ﬂash as you open the door, with the ignition off, to let you know that you are activating the system. This message reminds you to activate the theft-deterrent system. Here’s how to do it: 1. Open the door. 2. Lock the door with the power door lock switch or the remote keyless entry transmitter. The security light should come on and ﬂash. If using the remote keyless entry transmitter, the door does not need to be open. If the delayed locking feature is active, the alarm will not be activated until all doors are closed and the security light goes off. 3. Close all doors. The security light will stop ﬂashing and stay solid. The light should go off after approximately 30 seconds. The alarm is not armed until the security light goes off. If a door is opened without the key or the remote keyless entry transmitter, the alarm will go off. Your vehicle’s headlamps will ﬂash and the horn will sound for about two minutes, then will turn off to save the battery power. 2-18 Remember, the theft-deterrent system won’t activate if you lock the doors with a key or use the manual door lock. It activates only if you use a power door lock switch with the door open, or with the remote keyless entry transmitter. You should also remember that you can start your vehicle with the correct ignition key if the alarm has been set off. Here’s how to avoid setting off the alarm by accident: If you don’t want to activate the theft-deterrent system, the vehicle should be locked with the door key after the doors are closed. (cid:127) Always unlock a door with a key, or use the remote keyless entry transmitter. Unlocking a door any other way will set off the alarm if the system has been armed. If you set off the alarm by accident, unlock any door with the key. You can also turn off the alarm by pressing UNLOCK on the remote keyless entry transmitter or by placing the key in the ignition and turning it to START. Testing the Alarm The alarm can be tested by following these steps: 1. From inside the vehicle, lower the driver’s window and open the driver’s door. 2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the remote keyless entry transmitter. 3. Get out of the vehicle, close the door and wait for the security light to go out. 4. Then reach in through the window, unlock the door with the manual door lock and open the door. This should set off the alarm. If the alarm does not sound when it should but the vehicle’s headlamps ﬂash, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see Fuses and Circuit Breakers on page 5-111. If the alarm does not sound or the vehicle’s headlamps do not ﬂash, the vehicle should be serviced by an authorized service center. 2-19 (cid:127) Passlock® Your vehicle is equipped with the Passlock® theft-deterrent system. Passlock® is a passive theft-deterrent system. Passlock® enables fuel if the ignition lock cylinder is turned with a valid key. If a correct key is not used or the ignition lock cylinder is tampered with, fuel is disabled. If the engine stalls and the security light ﬂashes, wait until the light stops ﬂashing before trying to restart the engine. Remember to release the key from START as soon as the engine starts. If the engine is running and the security light comes on, you will be able to restart the engine if you turn the engine off. However, your Passlock® system is not working properly and must be serviced by your dealer. Your vehicle is not protected by Passlock® at this time. You may also want to check the fuse. See Fuses and Circuit Breakers on page 5-111. See your dealer for service. In an emergency, call the GM Roadside Assistance Center. See Roadside Assistance Program on page 7-6. Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate “break-in.” But it will perform better in the long run if you follow these guidelines: (cid:127) Keep your speed at 55 mph (88 km/h) or less for the ﬁrst 500 miles (805 km). (cid:127) Do not drive at any one speed — fast or slow — for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. (cid:127) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time your new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:127) Do not tow a trailer during break-in. See Towing a Trailer on page 4-65 for more information. 2-20 Ignition Positions With the key in the ignition switch, you can turn the key to four different positions. A (LOCK): This position locks your ignition and transmission. It’s a theft-deterrent feature. You will only be able to remove your key when the ignition is turned to LOCK. B (ACCESSORY): This position lets you use things like the radio, power windows and the windshield wipers when the engine is off. If your key seems stuck in LOCK and you Notice: can not turn it, be sure you are using the correct key; if so, is it all the way in? Turn the key only with your hand. Using a tool to force it could break the key or the ignition switch. If none of these works, then your vehicle needs service. C (RUN): This is the position for driving. D (START): This position starts your engine. Retained Accessory Power (RAP) Your vehicle may be equipped with a Retained Accessory Power (RAP) feature which will allow certain features on your vehicle to continue to work up to 10 minutes after the ignition key is turned to OFF. Your radio, power windows, sunroof (if equipped), and OnStar® System (if equipped) will work when the ignition key is in RUN or ACCESSORY. Once the key is turned from RUN to LOCK, these features will continue to work for up to 10 minutes or until a door is opened. 2-21 When starting your engine in very cold weather (below 0°F or −18°C), do this: 1. With your foot off the accelerator pedal, turn the ignition key to START and hold it there up to 15 seconds. When the engine starts, let go of the key. 2. If your engine still won’t start (or starts but then stops), it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for about three seconds. When the engine starts, let go of the key and accelerator. If the vehicle starts brieﬂy but then stops again, do the same thing, but this time keep the pedal down for ﬁve or six seconds. This clears the extra gasoline from the engine. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. Starting Your Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine won’t start in any other position – that’s a safety feature. To restart when you’re already moving, use NEUTRAL (N) only. Notice: Do not try to shift to PARK (P) if your vehicle is moving. If you do, you could damage the transmission. Shift to PARK (P) only when your vehicle is stopped. 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2. If it doesn’t start within 10 seconds, push the accelerator pedal all the way to the ﬂoor, while you hold the ignition key in START. When the engine starts, let go of the key and let up on the accelerator pedal. Wait about 15 seconds between each try. 2-22 Adjustable Throttle and Brake Pedal If your vehicle is equipped with this feature, you can change the position of the throttle and brake pedals. This feature is designed for shorter drivers, since the pedals can not move farther away from the standard position, but can move toward the driver for better pedal reach. The vehicle must be in PARK (P) for this feature to operate. The switch used to adjust the pedals is located on the driver’s side door panel. Engine Coolant Heater In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. Press the arrow at the end of the switch closest to you to move the pedals closer to your body. Press the arrow at the far end of the switch to move the pedals away from your body. 2-23 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you don’t, it could be damaged. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you’ll be parking your vehicle. The dealer can give you the best advice for that particular area. To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is located on the driver’s side of the engine compartment, near the power steering ﬂuid reservoir. 3. Plug it into a normal, grounded 110-volt AC outlet. {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 2-24 Automatic Transmission Operation There are several different positions for your shift lever. Your vehicle is equipped with an automatic transmission and features an electronic shift position indicator within the instrument panel cluster. This display must be powered anytime the shift lever is capable of being moved out of PARK (P). PARK (P): This position locks your rear wheels. It’s the best position to use when you start your engine because your vehicle can’t move easily. {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. CAUTION: (Continued) CAUTION: (Continued) To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into Park (P) on page 2-37. If you are pulling a trailer, see Towing a Trailer on page 4-65. {CAUTION: If you have four-wheel drive, your vehicle will be free to roll — even if your shift lever is in PARK (P) — if your transfer case is in NEUTRAL. So, be sure the transfer case is in a drive gear, two-wheel high (2H) or four-wheel high (4H) or four-wheel low (4L) — not in NEUTRAL. See Shifting Into Park (P) on page 2-37. 2-25 Notice: Shifting out of PARK (P) or NEUTRAL (N) with the engine running at high speed may damage the transmission. The repairs would not be covered by your warranty. Be sure the engine is not running at high speed when shifting your vehicle. DRIVE (D): This position is for normal driving. If you need more power for passing, and you’re: (cid:127) Going less than about 35 mph (56 km/h), push your accelerator pedal about halfway down. (cid:127) Going about 35 mph (56 km/h) or more, push the accelerator all the way down. You’ll shift down to the next gear and have more power. DRIVE (D) can be used when towing a trailer, carrying a heavy load, driving on steep hills or for off-road driving. You may want to shift the transmission to THIRD (3) or, if necessary, a lower gear selection if the transmission shifts too often. THIRD (3): This position is also used for normal driving, however it offers more power and lower fuel economy than DRIVE (D). REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transmission. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transmission, see If You Are Stuck: In Sand, Mud, Ice or Snow on page 4-52. NEUTRAL (N): In this position, your engine doesn’t connect with the wheels. To restart when you’re already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when your two-wheel drive vehicle is being towed. {CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. 2-26 SECOND (2): This position gives you more power but lower fuel economy. You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. If you manually select SECOND (2) in a light duty automatic transmission, the transmission will drive in second gear. You may use this feature for reducing the speed of the rear wheels when you are trying to start your vehicle from a stop on slippery road surfaces. FIRST (1): This position gives you even more power (but lower fuel economy) than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in FIRST (1) while the vehicle is moving forward, the transmission won’t shift into ﬁrst gear until the vehicle is going slowly enough. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place. On cold days, approximately 32°F (0°C) or colder, your transmission is designed to shift differently until the engine reaches normal operating temperature. This is intended to improve heater performance. Tow/Haul Mode Your vehicle may be equipped with a Tow/Haul mode. If so, the selector button is located on the end of the column shift lever. You can use this feature to assist when towing or hauling a heavy load. See Towing a Trailer on page 4-65 for more information. 2-27 When Tow/Haul mode is selected the Tow/Haul indicator light will illuminate. The Tow/Haul mode also interacts with the Autoride™ feature, if your vehicle is so equipped, to enhance the ride when trailering or with a loaded vehicle. See Autoride™ on page 4-64. Four-Wheel Drive If your vehicle has four-wheel drive, you can send your engine’s driving power to all four wheels for extra traction. To get the most satisfaction out of four-wheel drive, you must be familiar with its operation. Read the part that follows before using four-wheel drive. See the appropriate text for the transfer case in your vehicle. Notice: Driving on pavement in four-wheel drive for an extended period of time may cause premature wear on your vehicle’s powertrain. Do not drive in four-wheel drive on pavement for extended periods of time. Front Axle Locking Feature The front axle locks and unlocks automatically when you shift the transfer case. Some delay for the axle to lock or unlock is normal. 2-28 Automatic Transfer Case {CAUTION: Shifting the transfer case to NEUTRAL can cause your vehicle to roll even if the transmission is in PARK (P). You or someone else could be seriously injured. Be sure to set the parking brake before placing the transfer case in NEUTRAL. See Parking Brake on page 2-36. The transfer case buttons are located to the left of the instrument panel cluster. Use these buttons to shift into and out of four-wheel drive. You can choose among four driving settings: h (2HI): This setting is used for driving in most street and highway situations. Your front axle is not engaged in two-wheel drive. This setting also provides the best fuel economy. AUTO 4WD: This setting is ideal for use when road conditions are variable. When driving your vehicle in AUTO 4WD, the front axle is engaged, but the vehicle’s power is sent only to the rear wheels. When the vehicle senses a loss of traction, the system will automatically engage four-wheel drive. Driving in this mode results in slightly lower fuel economy than 2HI. G (4HI): Use the 4HI position when you need extra traction, such as on snowy or icy roads or in most off-road situations. This setting also engages your front axle to help drive your vehicle. This is the best setting to use when plowing snow. 2-29 5(4LO): This setting also engages your front axle and delivers extra torque. You may never need this setting. It sends maximum power to all four wheels. You might choose 4LO if you are driving off-road in deep sand, deep mud, deep snow and climbing or descending steep hills. {CAUTION: Shifting the transfer case to NEUTRAL can cause your vehicle to roll even if the transmission is in PARK (P). You or someone else could be seriously injured. Be sure to set the parking brake before placing the transfer case in NEUTRAL. See Parking Brake on page 2-36. NEUTRAL (N): Shift the vehicle’s transfer case to NEUTRAL only when towing your vehicle. See Recreational Vehicle Towing on page 4-55 or Towing Your Vehicle on page 4-55 for more information. Indicator lights in the button show which setting you are in. The indicator lights will come on brieﬂy when you turn on the ignition and one will stay on. If the lights do not come on, you should take your vehicle to your dealer for service. An indicator light will ﬂash while shifting the transfer case. It will remain illuminated when the shift is complete. If for some reason the transfer case cannot make a requested shift, it will return to the last chosen setting. If the SERVICE 4WD message stays on, you should take your vehicle to your dealer for service. See ″Service 4WD message″ under Driver Information Center (DIC) on page 3-56. Shifting into 4HI or AUTO 4WD Press and release the 4HI or AUTO 4WD button. This can be done at any speed (except when shifting from 4LO), and the indicator light will ﬂash while shifting. It will remain illuminated when the shift is completed. Shifting into 2HI Press and release the 2HI button. This can be done at any speed (except when shifting from 4LO). 2-30 Shifting into 4LO To shift to the 4LO position, the ignition must be in RUN and the vehicle must be stopped or moving less than 3 mph (4.8 km/h) with the transmission in NEUTRAL (N). The preferred method for shifting into 4LO is to have your vehicle moving 1 to 2 mph (1.6 to 3.2 km/h). Press and release the 4LO button. You must wait for the 4LO indicator light to stop ﬂashing and remain illuminated before shifting your transmission in gear. Notice: Shifting the transmission into gear before the 4LO indicator light has stopped ﬂashing could damage the transfer case. To help avoid damaging your vehicle, always wait for the 4LO indicator light to stop ﬂashing before shifting the transmission into gear. It is typical for your vehicle to exhibit signiﬁcant engagment noise and bump when shifting between 4LO and 4HI ranges or from NEUTRAL with the engine running. If the 4LO button is pressed when your vehicle is in gear and/or moving, the 4LO indicator light will ﬂash for 30 seconds and not complete the shift unless your vehicle is moving less than 3 mph (4.8 km/h) and the transmission is in NEUTRAL (N). After 30 seconds the transfer case will shift to 4HI mode. Shifting Out of 4LO To shift from 4LO to 4HI, AUTO 4WD or 2HI your vehicle must be stopped or moving less than 3 mph (4.8 km/h) with the transmission in NEUTRAL (N) and the ignition in RUN. The preferred method for shifting out of 4LO is to have your vehicle moving 1 to 2 mph (1.6 to 3.2 km/h). Press and release the 4HI, AUTO 4WD or 2HI button. You must wait for the 4HI, AUTO 4WD or 2HI indicator light to stop ﬂashing and remain illuminated before shifting your transmission into gear. Notice: Shifting the transmission into gear before the 4LO indicator light has stopped ﬂashing could damage the transfer case. To help avoid damaging your vehicle, always wait for the 4LO indicator light to stop ﬂashing before shifting the transmission into gear. It is typical for your vehicle to exhibit signiﬁcant engagment noise and bump when shifting between 4LO and 4HI ranges or from NEUTRAL with the engine running. If the 4HI, AUTO 4WD or 2HI switch is pressed when your vehicle is in gear and/or moving, the 4HI, AUTO 4WD or 2HI indicator light will ﬂash for 30 seconds but will not complete the shift unless your vehicle is moving less than 3 mph (4.8 km/h) and the transmission is in NEUTRAL (N). 2-31 Shifting into NEUTRAL To shift the transfer case to NEUTRAL do the following: 1. Make sure the vehicle is parked so that it will not roll. 2. Set the parking brake. 3. Start the vehicle or turn the ignition to RUN. 4. Connect the vehicle to the towing vehicle. 5. Put the transmission in NEUTRAL (N). 6. Shift the transfer case to 2HI. 7. Simultaneously press and hold the 2HI and 4LO buttons for 10 seconds. The red NEUTRAL light will come on when the transfer case shift to NEUTRAL is complete. 8. Shift the transmission to REVERSE (R) for one second, then shift the transmission to DRIVE (D) for one second. 9. Turn the ignition to LOCK. 10. Place the transmission shift lever in PARK (P). 11. Release the parking brake prior to towing. Shifting Out of NEUTRAL To shift out of NEUTRAL: 1. Set the parking brake and apply the regular brake pedal. 2. Shift the transmission to NEUTRAL (N) and turn the ignition to RUN with the engine off. 3. Press the button for the desired transfer case shift position (2HI, 4HI, AUTO 4WD OR 4LO). 4. After the transfer case has shifted out of NEUTRAL the red light will go out. 5. Release the parking brake. 6. You may start the engine and shift the transmission to the desired position. Excessively shifting the transfer case into or out of the different modes may cause the transfer case to enter the shift protection mode. This will protect the transfer case from possible damage and will only allow the transfer case to respond to one shift per 10 seconds. The transfer case may stay in this mode for up to three minutes. 2-32 All-Wheel Drive with Stabilitrak® With this feature, engine power is sent to all four wheels all the time. This is like four-wheel drive, but there is no separate lever or switch to engage or disengage the front axle. It is fully automatic, and adjust itself as needed for road conditions. The transfer case buttons are located to the left of the instrument panel cluster. You can choose among three driving settings: d (Stabilitrak®): This button is used with the Stabilitrak® system and is also used to shift the transfer case into Neutral (N). For more information on using Stabilitrak® see Stabilitrak® System on page 4-12. f (All-Wheel Drive): This setting delivers power to all four wheels as needed depending on road and driving conditions. g (4LO): This setting delivers extra torque. You may never need this setting. It sends maximum power to all four wheels. You might choose 4LO if you are driving off-road in deep sand, deep mud, deep snow and climbing or descending steep hills. Use these buttons to shift into and out of four-wheel drive. 2-33 {CAUTION: Shifting the transfer case to NEUTRAL can cause your vehicle to roll even if the transmission is in PARK (P). You or someone else could be seriously injured. Be sure to set the parking brake before placing the transfer case in NEUTRAL. See Parking Brake on page 2-36. NEUTRAL: Shift the vehicle’s transfer case to NEUTRAL only when towing your vehicle. See Recreational Vehicle Towing on page 4-55 or Towing Your Vehicle on page 4-55 for more information. Indicator lights in the buttons show which setting you are in. The indicator lights will come on brieﬂy when you turn on the ignition and one will stay on. If the lights do not come on, you should take your vehicle to your dealer for service. An indicator light will ﬂash while shifting the transfer case. It will remain illuminated when the shift is complete. If for some reason the transfer case cannot make a requested shift, it will return to the last chosen setting. If the SERVICE 4WD message stays on, you should take your vehicle to your dealer for service. See SERVICE 4WD under Driver Information Center (DIC) on page 3-56. 2-34 Shifting into 4LO To shift to the 4LO position, the ignition must be in RUN and the vehicle must be stopped or moving less than 3 mph (4.8 km/h) with the transmission in NEUTRAL (N). The preferred method for shifting into 4LO is to have your vehicle moving 1 to 2 mph (1.6 to 3.2 km/h). Press and release the 4LO switch. You must wait for the 4LO indicator light to stop ﬂashing and remain illuminated before shifting your transmission in gear. Notice: Shifting the transmission into gear before the 4LO indicator light has stopped ﬂashing could damage the transfer case. To help avoid damaging your vehicle, always wait for the 4LO indicator light to stop ﬂashing before shifting the transmission into gear. If the 4LO button is pressed when your vehicle is in gear and/or moving, the 4LO indicator light will ﬂash for 30 seconds and not complete the shift unless your vehicle is moving less than 3 mph (4.8 km/h) and the transmission is in NEUTRAL (N). After 30 seconds the transfer case will return to the setting last chosen. When in 4LO, the vehicle stability is disabled. For more information see Stabilitrak® System on page 4-12. Shifting Out of 4LO To shift from 4LO to All-Wheel Drive your vehicle must be stopped or moving less than 3 mph (4.8 km/h) with the transmission in NEUTRAL (N) and the ignition in RUN. The preferred method for shifting out of 4LO is to have your vehicle moving 1 to 2 mph (1.6 to 3.2 km/h). Press and release the All-Wheel Drive button. You must wait for the AWD indicator light to stop ﬂashing and remain illuminated before shifting your transmission into gear. If the All-Wheel Drive button is pressed when your vehicle is in gear and/or moving, the All-Wheel Drive indicator light will ﬂash for 30 seconds but will not complete the shift unless your vehicle is moving less than 3 mph (4.8 km/h) and the transmission is in NEUTRAL (N). Shifting into NEUTRAL To shift the transfer case to NEUTRAL do the following: 1. Make sure the vehicle is parked so that it will not roll. 2. Set the parking brake. 3. Start the vehicle or turn the ignition to RUN. 4. Connect the vehicle to the towing vehicle. 5. Put the transmission in NEUTRAL (N). 6. Shift the transfer case to All-Wheel Drive. 7. Simultaneously press and hold the Stabilitrak® and 4LO buttons for 10 seconds. The red NEUTRAL light will come on when the transfer case shift to NEUTRAL is complete. 8. Shift the transmission to REVERSE (R) for one second, then shift the transmission to DRIVE (D) for one second. 9. Turn the ignition to LOCK. 10. Place the transmission shift lever in PARK (P). 11. Release the parking brake prior to towing. Shifting Out of NEUTRAL To shift out of NEUTRAL: 1. Set the parking brake and apply the regular brake pedal. 2. Shift the transmission to NEUTRAL (N) and turn the ignition to RUN with the engine off. 3. Press the button for the desired transfer case shift position (All-Wheel Drive or 4LO). 4. After the transfer case has shifted out of NEUTRAL the red light will go out. 5. Release the parking brake. 6. You may start the engine and shift the transmission to the desired position. 2-35 Parking Brake To set the parking brake, hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your left foot. A chime will activate and the warning light will ﬂash when the parking brake is applied and the vehicle is moving at least 3 mph (5 km/h) for at least three seconds. To release the parking brake, hold the regular brake pedal down. Pull the bottom edge of the lever, located above the parking brake pedal, with the parking brake symbol, to release the parking brake. If the ignition is on when the parking brake is released, the brake system warning light will go off. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and are parking on any hill, see Towing a Trailer on page 4-65. 2-36 Shifting Into Park (P) {CAUTION: 1. Hold the brake pedal down with your right foot and set the parking brake. 2. Move the shift lever into the PARK (P) position like this: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. With four-wheel drive, if your transfer case is in NEUTRAL, your vehicle will be free to roll, even if your shift lever is in PARK (P). So, be sure the transfer case is in a drive gear — not in NEUTRAL. If you are pulling a trailer, see Towing a Trailer on page 4-65. (cid:127) Pull the shift lever toward you. 2-37 Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. If you have four-wheel drive and your transfer case is in NEUTRAL, your vehicle will be free to roll, even if your shift lever is in PARK (P). So be sure the transfer case is in a drive gear – not in NEUTRAL. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Don’t leave your vehicle with the engine running unless you have to. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and the parking brake is ﬁrmly set before you leave it. After you move the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pulling it toward you. If you can, it means that the shift lever wasn’t fully locked into PARK (P). (cid:127) Move the lever up as far as it will go. 3. Be sure the transfer case is in a drive gear – not in NEUTRAL (N). 4. Turn the ignition key to LOCK. 5. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). 2-38 Torque Lock If you are parking on a hill and you don’t shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called ″torque lock.″ To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into Park (P) on page 2-37. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transmission, so you can pull the shift lever out of PARK (P). Shifting Out of Park (P) Your vehicle has an automatic transmission shift lock control system which locks the shift lever in PARK when the ignition is in the LOCK position. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN. See Automatic Transmission Operation on page 2-25. If you cannot shift out of PARK (P), ease pressure on the shift lever and push the shift lever all the way up into PARK (P) as you maintain brake application. Then, move the shift lever into the gear you want. If you ever hold the brake pedal down but still can’t shift out of PARK (P), try this: 1. Turn the key to ACCESSORY. There is no shift interlock in this key position. 2. Apply and hold the brake until the end of Step 4. 3. Shift the transmission to NEUTRAL (N). 4. Start the vehicle and then shift to the gear you want. 5. Have the system ﬁxed as soon as you can. 2-39 Parking Over Things That Burn Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can not see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system had been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. 2-40 Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier Caution under Engine Exhaust on page 2-40. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-48. {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). {CAUTION: Four-wheel drive vehicles with the transfer case in NEUTRAL will allow the vehicle to roll, even if your shift lever is in PARK (P). So, be sure the transfer case is in a drive gear — not in NEUTRAL. Always set your parking brake. Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) on page 2-37. If you are pulling a trailer, see Towing a Trailer on page 4-65. 2-41 Mirrors Manual Rearview Mirror Pull the tab under the mirror toward you to reduce glare from headlamps behind you after dark. Push the tab away from you for normal daytime operation. Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display Your vehicle may have this feature. When on, an automatic dimming mirror automatically dims to the proper level to minimize glare from lights behind you after dark. Temperature and Compass Display Press the on/off button, located to the far left, brieﬂy to turn the compass/temperature display on or off. If the display reads CAL, you will need to calibrate the compass. For more information on calibration, see below. To adjust between Fahrenheit and Celsius do the following: 1. Press and hold the on/off button for approximately four seconds until either a ﬂashing °F, or °C appears. 2. Press the button again to change the display to the desired unit of measurement. After approximately four seconds of inactivity, the new unit will be locked in and the compass/temperature display will return. If an abnormal temperature reading is displayed for an extended period of time, please consult your dealer. Under certain circumstances, a delay in updating the temperature is normal. The mirror also includes a dual display in the upper right corner of the mirror face. The compass reading and the outside temperature will both appear in the display at the same time. P (On/Off): This is the on/off button. 2-42 Automatic Dimming Mirror Operation The automatic dimming mirror function is turned on automatically each time the ignition is started. To operate the automatic dimming mirror, do the following: 1. Make sure the green indicator light, located to the left of the on/off button, is lit. If it’s not, press and hold the on/off button for approximately six seconds until the green light comes on, indicating that the mirror is in automatic dimming mode. 2. Turn off the automatic dimming mirror function by pressing and holding the on/off button for approximately six seconds, until the green indicator light turns off. Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside of zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance do the following: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the on/off button until a Z and a zone number appears in the display. The compass is now in zone mode. 3. Keep pressing the on/off button until the desired zone number appears in the display. Release the button. After approximately four seconds of inactivity, the new zone number will be locked in and the compass/temperature display will return. 4. Calibrate the compass as described below. 2-43 Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Automatic Dimming Rearview Mirror with Compass and Temperature Display If your vehicle is equipped with an automatic mirror, it will, when on, automatically dim to the proper level to minimize glare from lights behind you after dark. The mirror also includes a display in the upper right corner of the mirror face. The compass reading and the outside temperature will both appear in the display at the same time. The dual display can be turned on or off by brieﬂy pressing either the TEMP or the COMP button. Compass Calibration The compass may need calibration if one of the following occurs: (cid:127) After approximately ﬁve seconds, the display does not show a compass heading (N for North, for example), there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder or a similar magnetic item. The compass does not display the correct heading and the compass zone variance is set correctly. In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, push the on/off button for approximately 12 seconds or until CAL is displayed. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Passenger Air Bag Indicator Your vehicle may be equipped with a passenger air bag indicator, on the mirror glass, just above the buttons. If your vehicle has this feature, the mirror will display the word ON, or an air bag symbol in Canada, when the passenger air bag is enabled. For more information, see Passenger Sensing System on page 1-82. 2-44 (cid:127) Temperature Display The temperature can be displayed by pressing the TEMP button. Pressing the TEMP button once brieﬂy, will toggle the temperature reading on and off. To alternate the temperature reading between Fahrenheit and Celsius, press and hold the TEMP button for approximately four seconds until the display blinks °F and °C. Press and release the TEMP button to toggle between the Fahrenheit and Celsius readings. After approximately four seconds of inactivity, the display will stop blinking and display the last selection made. If an abnormal reading is displayed, for an extended period of time, please consult your dealer. Under certain circumstances, a delay in updating the temperature is normal. Automatic Dimming Mirror Operation The time period you need to press and hold the TEMP button to turn the automatic dimming feature on or off is approximately eight seconds. The indicator light to the left of the TEMP button will still turn on or off to show you when the automatic dimming feature is activated. Once the mirror is turned off, it will remain off until it is turned back on, or until the vehicle is restarted. Compass Operation Press the COMP button once brieﬂy to turn the compass on or off. When the ignition and the compass feature are on, the compass will show two character boxes for approximately two seconds. After two seconds, the mirror will display the compass heading. Compass Calibration The compass may need calibration if one of the following occurs: If CAL is displayed while driving in the vehicle. (cid:127) After approximately ﬁve seconds, the display does not show a compass heading (N for North, for example), there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder or a similar magnetic item. The compass does not display the correct heading and the compass zone variance is set correctly. In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, push in the COMP button for approximately eight seconds or until CAL is displayed. The compass can be calibrated by driving the vehicle in circles at ﬁve mph (8 km/h) or less until the display reads a direction. 2-45 (cid:127) (cid:127) Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the COMP button for ﬁve seconds until a zone number appears in the display. 3. Press the COMP button on the bottom of the mirror until the new zone number appears in the display. After you stop pressing the button, the display will show a compass direction within a few seconds. 2-46 Passenger Air Bag Indicator Your mirror may be equipped with a passenger air bag indicator on the mirror glass, just above the buttons. If you have this feature the mirror will display the word ON, or an airbag symbol in Canada, when the passenger air bag is enabled. For more information see Passenger Sensing System on page 1-82. Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Outside Manual Mirrors Adjust your outside mirrors so you can just see the side of your vehicle and have a clear view of objects behind you. The mirrors can be folded in to enter narrow areas. The use of hood-mounted air deﬂectors and add-on convex mirror attachments may adversely affect mirror performance. Outside Camper-Type Mirrors If your vehicle is equipped with camper-type mirrors, they can be adjusted so you can have a clear view of the objects behind you. Pull out the mirror head to extend it for better visibility when towing a trailer. 2-47 Outside Power Mirrors If your vehicle is equipped with power outside mirrors, the controls are located on the driver’s door armrest. Move the selector switch located above the control pad to the left or right to choose the mirror you want to adjust, then press the dots located on the four-way control pad to adjust the mirror. The mirrors also include a memory function which works in conjunction with the memory seats. See “Memory Seats” in the Index for more information. Outside Power Camper-Type Mirror If your vehicle is equipped with outside power camper-type mirrors, they can be adjusted so you can have a clear view of objects behind you. To extend the mirrors move the selector switch, located above the mirror control, to the middle position. The mirror control will illuminate. Press the left side of the mirror control to slide the mirror heads away from the body of the vehicle. Press the right side of the mirror control to slide the mirror heads toward the body of the vehicle. Outside Power Foldaway Mirrors If your vehicle is equipped with this feature, the controls are located on the driver’s door armrest. 2-48 Move the upper selector switch to the left or right to choose the mirror you want to adjust; then press the dots located on the four-way control pad to adjust the mirror. The mirrors may also include a memory function which works in conjunction with the memory seats. See “Memory Seats” under Memory Seat on page 2-61 for more information. To fold or unfold the mirrors, move the selector switch, located about the mirror control, to the middle position. The mirror control will illuminate. Press the right or left side of the mirror control to fold or unfold the mirrors. You may notice the mirror glass adjust as the mirrors fold in; this is normal. The mirror glass will reposition itself once the mirrors are unfolded. If the mirrors are accidentally folded/unfolded manually, they may shake or ﬂutter at normal driving speeds and may not stay in the unfolded position. If this happens, you will need to reset the mirrors. See “Resetting the Power Foldaway Mirrors” next. Resetting the Power Foldaway Mirrors You will need to reset the power foldaway mirrors if the following occurs: They are accidentally manually folded/unfolded. The mirrors will not stay in the unfolded position. The mirrors shake and ﬂutter at normal driving speeds. To reset the power foldaway mirrors, fold and unfold then at least three times using the mirror controls. This will reset them to their normal detent position. Outside Automatic Dimming Mirror If your vehicle is equipped with this feature, the driver’s outside mirror will adjust for the glare of headlamps behind you. This feature is controlled by the on and off settings found on the electrochromic mirror. See Automatic Dimming Rearview Mirror with Compass and Temperature Display on page 2-44. 2-49 (cid:127) (cid:127) (cid:127) Outside Curb View Assist Mirrors If your vehicle has the optional memory package you may have this feature. The vehicle’s mirrors are capable of performing the curb view assist mirror function. This feature will cause the passenger’s and/or driver’s mirror to tilt to a preselected position when the vehicle is in REVERSE (R). This feature may be useful in allowing you to view the curb when you are parallel parking. When the vehicle is shifted out of REVERSE (R) and a short delay has occurred, the passenger’s and/or driver’s mirror will return to its original position. To change the preselected tilt position, adjust the mirrors to the desired position while the vehicle is in REVERSE (R). When the vehicle is shifted out of REVERSE (R), this new position is saved in memory as the tilt position. You may be able to enable/disable this feature through the Driver Information Center. See Driver Information Center (DIC) on page 3-56. Outside Convex Mirror Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. Outside Heated Mirrors The outside rearview mirrors with this option have a defrost mode. To turn on the defrost feature, press the rear window defogger button. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 3-27 for further information. 2-50 OnStar® System OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and state of the art call centers to provide you with a wide range of safety, security, information and convenience services. A complete OnStar® user’s guide and the terms and conditions of the OnStar® Subscription Service Agreement are included in your OnStar®-equipped vehicle’s glove box literature. For more information, visit www.onstar.com, contact OnStar® at 1−888−4−ONSTAR (1−888−466−7827), or press the blue OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. A completed Subscription Service Agreement is required prior to delivery of OnStar® services and prepaid calling minutes are also required for OnStar® Personal Calling and OnStar® Virtual Advisor use. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com. OnStar® Services One of the following plans is normally included for a speciﬁc duration with each vehicle equipped with OnStar®. You can upgrade or extend your OnStar® service plan to meet your needs. Safe and Sound Plan (cid:127) Automatic Notiﬁcation of Air Bag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Assistance (cid:127) AccidentAssist (cid:127) Remote Door Unlock (cid:127) Remote Diagnostics (cid:127) Online Concierge 2-51 Directions and Connections Plan (cid:127) All Safe and Sound Plan services (cid:127) Route Support (cid:127) RideAssist Information and Convenience Services Luxury and Leisure Plan (cid:127) All Directions and Connections Plan services (cid:127) Personal Concierge OnStar® Personal Calling With OnStar® Personal Calling, you have a safer way to stay connected while driving. It’s a hands-free wireless phone that’s integrated into your vehicle. You can place calls nationwide using voice-activated dialing with no contracts and no additional roaming charges. To ﬁnd out more about OnStar® Personal Calling, refer to the OnStar® owner’s guide in your vehicle’s glove box, or call OnStar® at 1−888−4−ONSTAR (1−888−466−7827). OnStar® Virtual Advisor With OnStar® Virtual Advisor you can listen to your favorite news, entertainment and information topics, such as traffic and weather reports, stock quotes and sports scores. You listen to your e-mail through your vehicle’s speakers, and reply with your hands on the wheel and your eyes on the road. OnStar® Steering Wheel Controls g: If your vehicle is equipped with the steering wheel control buttons you can use them to interact with the OnStar® system. See the OnStar® manual provided with your vehicle for more information. 2-52

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2004 Chevrolet Suburban Owners Manual