Download PDF Manual

upshifts and downshifts. This shift stabilization feature is designed to determine, before making an upshift, if the engine is able to maintain vehicle speed by analyzing things such as vehicle speed, throttle position, and vehicle load. If the shift stabilization feature determines that a current vehicle speed cannot be maintained, the transmission does not upshift and instead holds the current gear. In some cases, this could appear to be a delayed shift, however the transmission is operating normally. The transmission uses adaptive shift controls. Adaptive shift controls continually compares key shift parameters to pre-programmed ideal shifts stored in the transmissions computer. The transmission constantly makes adjustments to improve vehicle performance according to how the


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (36,1)


9-36


Driving and Operating


vehicle is being used, such as with a heavy load or when temperature changes. During this adaptive shift control process, shifting might feel different as the transmission determines the best settings. When temperatures are very cold, the Allison Transmission and Hydra-Matic 6-Speed transmission's gear shifting could be delayed providing more stable shifts until the engine warms up. Shifts could be more noticeable with a cold transmission. This difference in shifting is normal. M (Manual Mode): This position is available on vehicles with the Allison Transmission or Hydra-Matic 6-Speed transmission. It lets drivers select the range of gears appropriate for current driving conditions. If the vehicle has this feature, see “Range Selection Mode” under Manual Mode on page 9‑37.


3 (Third): This position is also used for normal driving. It reduces vehicle speed more than D (Drive) without using the brakes. You might choose 3 (Third) instead of D (Drive) when driving on hilly, winding roads, when towing a trailer, so there is less shifting between gears and when going down a steep hill. 2 (Second): This position reduces vehicle speed even more than 3 (Third) without using the brakes. You can use 2 (Second) on hills. It can help control vehicle speed as you go down steep mountain roads, but then you would also want to use the brakes off and on. If you manually select 2 (Second) in an automatic transmission, the transmission will start in second gear. You can use this feature for reducing the speed of the rear wheels when you are trying to start the vehicle from a stop on slippery road surfaces.


1 (First): For the Hydra-Matic 4-Speed transmission this position reduces vehicle speed even more than 2 (Second) without using the brakes. You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in 1 (First) while the vehicle is moving forward, the transmission does not shift into first gear until the vehicle is going slowly enough. For an Allison Transmission or Hydra-Matic 6-Speed transmission, this position reduces vehicle speed without using the brakes. You can use it for major/severe downgrades and off-road driving where the vehicle would otherwise accelerate due to steepness of grade. When you shift to 1 (First) it provides the lowest gear appropriate to current road speed and continues to downshift as the vehicle slows, eventually downshifting to 1 (First) gear. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (37,1)


accelerator pedal may damage the transmission. The repair will not be covered by the vehicle warranty. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place. Normal Mode Grade Braking Vehicles with a gasoline engine and 6-Speed automatic transmission have Normal Mode Grade Braking that is enabled when the vehicle is started, but is not enabled in Range Selection Mode. It assists in maintaining desired vehicle speeds when driving on downhill grades by using the engine and transmission to slow the vehicle. The first time the system engages for each ignition key cycle, a DIC message will be displayed. See Transmission Messages on page 5‑44. To disable or enable Normal Mode Grade Braking within the current ignition key cycle, press and hold the Tow/Haul button for


three seconds. A DIC message displays. See Transmission Messages on page 5‑44. For iother forms of grade braking, see Tow/Haul Mode on page 9‑38
and Cruise Control on page 9‑59.


Manual Mode


Range Selection Mode (Allison® Transmission or Hydra-Matic® 6-Speed Transmission)


The vehicle may have a Range Selection Mode. The Range Selection Mode helps control the vehicle's transmission and vehicle speed while driving down hill or towing a trailer by letting you select a desired range of gears.


Driving and Operating


9-37


To use this feature, do the following: 1. Move the shift lever to


M (Manual Mode).


2. Press the plus/minus buttons, located on the steering column shift lever, to select the desired range of gears for current driving conditions.


When M (Manual Mode) is selected a number displays next to the M, indicating the current gear. This number is the highest gear that can be used. However, the vehicle can automatically shift to lower gears as it adjusts to driving conditions. This means that all gears below that number are available. When 5 (Fifth) is selected, 1 (First) through 5 (Fifth) gears are automatically shifted by the vehicle, but 6 (Sixth) cannot be used until the plus/minus button located on the steering column lever is used to change to the gear.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (38,1)


9-38


Driving and Operating


Low Traction Mode If the vehicle has the Allison Transmission, a 4-Speed automatic transmission, or the Hydra-Matic 6-Speed Automatic Transmission with the 6.0L engine, it has a Low Traction Mode that assists in vehicle acceleration when road conditions are slippery, such as with ice or snow. While the vehicle is at a stop, select the second gear range using Range Selection Mode. This will limit torque to the wheels helping to prevent the tires from spinning.


Grade Braking is not available when Range Selection Mode is active. See Tow/Haul Mode on page 9‑38. While using Range Selection Mode, Cruise Control and the Tow/Haul Mode can be used. If the vehicle has an exhaust brake, it can also be used, but will not automatically downshift the transmission. See Exhaust Brake in the Duramax Diesel supplement. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. The repair will not be covered by the vehicle warranty. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place.


Tow/Haul Mode


4-Speed Automatic Transmission


6-Speed Automatic Transmission Vehicles with an automatic transmission have a Tow/Haul Mode. The Tow/Haul Mode adjusts the transmission shift pattern to reduce shift cycling, providing increased performance, vehicle control, and transmission cooling when driving down steep hills or Mountain grades, towing, or hauling heavy loads.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (39,1)


The selector button is located on the end of the shift lever. Turn the Tow/ Haul Mode on and off by pressing the button. When the Tow/Haul Mode is enabled, a light on the instrument panel cluster will come on. See Tow/Haul Mode Light on page 5‑25 and Hill and Mountain Roads on page 9‑11 for more information. Also see “Tow/Haul Mode” under Towing Equipment on page 9‑93 for more information. Tow/Haul Mode Grade Braking (6-Speed Automatic Transmission) Tow/Haul Mode Grade Braking is only enabled while the Tow/Haul Mode is selected and the vehicle is not in the Range Selection Mode. See “Tow/Haul Mode” listed previously and Manual Mode on page 9‑37. Tow/Haul Mode Grade Braking assists in maintaining desired vehicle speeds when driving


on downhill grades by using the engine and transmission to slow the vehicle. On vehicles with a gasoline engine, to disable or enable Tow/Haul Grade Braking within the current ignition key cycle, press and hold the Tow/Haul button for three seconds. A DIC message will be displayed. See Transmission Messages on page 5‑44. On vehicles with a diesel engine. Tow/Haul Mode Grade Braking can be enabled or disabled by pressing the Tow/Haul Mode button. Use the exhaust brake and Tow/Haul Mode for maximum grade braking. See Towing Equipment on page 9‑93 for more information. For other forms of grade braking, see Automatic Transmission on page 9‑33 and Cruise Control on page 9‑59.


Driving and Operating


9-39


Manual Transmission


If the vehicle is equipped with a manual transmission, this is the shift pattern. Here is how to operate the manual transmission: 1 (First): Press the clutch pedal and shift into 1 (First). Then, slowly let up on the clutch pedal as you slowly press down on the accelerator pedal.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (40,1)


Shift Speeds


{ WARNING


If you skip a gear when you downshift, you could lose control of the vehicle. You could injure yourself or others. Do not shift down more than one gear at a time when you downshift.


9-40


Driving and Operating


You can shift into 1 (First) when you are going less than 30 km/h (20 mph). If you have come to a complete stop and it is hard to shift into 1 (First), put the shift lever in Neutral and let up on the clutch. Then press the clutch pedal back down and shift into 1 (First). 2 (Second): Press the clutch pedal as you let up on the accelerator pedal and shift into 2 (Second). Then, slowly let up on the clutch pedal as you press the accelerator pedal. 3 (Third), 4 (Fourth) and 5 (Fifth): Shift into 3 (Third), 4 (Fourth) and 5 (Fifth) the same way you do for 2 (Second). Slowly let up on the clutch pedal as you press the accelerator pedal. To stop, let up on the accelerator pedal and press the brake pedal. Just before the vehicle stops, press the clutch pedal and the brake pedal, and shift to Neutral. Neutral: Use this position when you start or idle the engine.


R (Reverse): To back up, press the clutch pedal. After the vehicle stops, shift into R (Reverse). Slowly let up on the clutch pedal as you press the accelerator pedal. If it is hard to shift, let the shift lever return to Neutral and release the clutch pedal. Then press the clutch again and shift into R (Reverse). Do not attempt to shift into 5 (Fifth) prior to shifting into R (Reverse). The transmission has a lock out feature which prevents a 5 (Fifth) gear to R (Reverse) gear shift. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped. Use R (Reverse), along with the parking brake, for parking the vehicle.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (41,1)


If the vehicle has StabiliTrak®, shifting into Four-Wheel Drive Low will turn Traction Control and StabiliTrak off. See StabiliTrak® System on page 9‑56. Front Axle The front axle engages and disengages automatically when you shift the transfer case. Some delay for the axle to engage or disengage is normal. Manual Transfer Case


Driving and Operating


9-41


The transfer case shift lever is on the floor to the right of the driver. Use this lever to shift into and out of Four-Wheel Drive.


A Four-Wheel Drive indicator light comes on when you shift into four-wheel drive and the front axle engages. See Four-Wheel-Drive Light on page 5‑25. Some delay between shifting and when the indicator light comes on is normal.


Drive Systems


Four-Wheel Drive If the vehicle has Four-Wheel Drive, you can send the engine's driving power to all four wheels for extra traction. To get the most satisfaction out of Four-Wheel Drive, you must be familiar with its operation. Read the following before using Four-Wheel Drive. See the appropriate text for the transfer case in the vehicle. Notice: Driving on clean, dry pavement in Four-Wheel Drive High or Four-Wheel Drive Low for an extended period of time may cause premature wear on the vehicle's powertrain. Do not drive on clean, dry pavement in Four-Wheel Drive High or Four-Wheel Drive Low for extended periods of time. While driving on clean dry pavement and during tight turns, you may experience vibration in the steering system.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (42,1)


9-42


Driving and Operating


Recommended Transfer Case Settings


Driving Conditions


Normal Severe Extreme


Vehicle in Tow*


Transfer Case Settings


4m


4n


2m


YES


YES


YES


YES


*See Recreational Vehicle Towing on page 10‑89 or Towing the Vehicle on page 10‑89.


Notice: Driving on clean, dry pavement in four-wheel drive for an extended period of time can cause premature wear on the vehicle's powertrain. Do not drive on clean, dry pavement in Four-Wheel Drive for extended periods of time.


4 n (Four-Wheel Drive Low): This setting also engages the front axle and delivers extra torque. You may never need Four-Wheel Drive Low. It sends maximum power to all four wheels. You might choose Four-Wheel Drive Low if you are driving off-road in deep sand, deep mud, deep snow, and while climbing or descending steep hills.


If the vehicle has StabiliTrak®, shifting into Four-Wheel Drive Low will turn Traction Control and StabiliTrak off. See StabiliTrak® System on page 9‑56.


A parking brake symbol is located next to the N (Neutral) symbol as a reminder to set the parking brake before shifting the transfer case into N (Neutral).


{ WARNING Shifting the transfer case to N (Neutral) can cause the vehicle to roll even if the transmission is in P (Park). You or someone else could be seriously injured. Be sure to set the parking brake


(Continued)


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (43,1)


Driving and Operating


9-43


WARNING (Continued)


before placing the transfer case in N (Neutral). See Parking Brake on page 9‑54.


N (Neutral): Shift to this setting only when the vehicle needs to be towed. See Recreational Vehicle Towing on page 10‑89 or Towing the Vehicle on page 10‑89. 2 m (Two-Wheel Drive High): This setting is used for driving in most street and highway situations. The front axle is not engaged in two-wheel drive. This setting also provides the best fuel economy. 4 m (Four-Wheel Drive High): Use this setting when you need extra traction, such as on snowy or icy roads or in most off-road situations. This setting also engages the front axle to help drive your vehicle. This is the best setting to use when plowing snow.


You can shift from Two-Wheel Drive High to Four-Wheel Drive High or Four-Wheel Drive High to Two-Wheel Drive High while the vehicle is moving. In extremely cold weather, it may be necessary to stop or slow the vehicle to shift into Four-Wheel Drive High.


When Using the Manual Transfer Case . Shifts into or out of Four-Wheel Drive Low or N (Neutral) should be made using quick motions to avoid excessive gear grinding. Shifting slowly may make it more difficult to shift.


. You may notice that it is harder to shift when the vehicle is cold. After the vehicle warms up the shifting will return to normal. . While in Four-Wheel High or


Four-Wheel Drive Low you may experience reduced fuel economy.


. Avoid driving in Four-Wheel


Drive on clean, dry pavement. It may cause your tires to wear faster, make the transfer case harder to shift, and run noisier. If the transfer case shifter is in the N (Neutral) position and you have difficulty reaching the selected transfer case mode, with the engine running, shift the transmission momentarily to D (Drive) and then back to N (Neutral). This will realign the gear teeth in the transfer case and allow you to complete the shift.


Shifting from Two-Wheel Drive High to Four-Wheel Drive High . Shifts between Two-Wheel Drive High and Four-Wheel Drive High can be made at any vehicle speed.


. Shift the transfer case lever in


one continuous motion into either the Four-Wheel Drive High or Two-Wheel Drive High position.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (44,1)


9-44


Driving and Operating


. Shifting from Two-Wheel Drive High to Four-Wheel Drive High while the vehicle is in motion may require that moderate force be applied to the shift lever for a few seconds before Four-Wheel Drive High can be engaged, especially in cold weather. In extremely cold weather, it may be necessary to slow or stop the vehicle to shift into Four-Wheel Drive High.


. While in Four-Wheel Drive High, the vehicle can be driven at any posted legal speed limit.


Shifting In or Out of Four-Wheel Drive Low Notice: Shifting the transfer case into Four-Wheel-Drive Low while moving at speeds faster than 5 km/h (3 mph) may cause premature wear to the transfer case, and may cause the gears to grind. To avoid causing premature wear, and grinding the gears, do not shift the transfer


case into Four-Wheel-Drive Low while the vehicle is moving faster than 5 km/h (3 mph). . Shifting into Four-Wheel Drive


Low should be done, if possible, with the vehicle at a slight roll, 5 km/h (3 mph) or less.


. Shift the transmission into


N (Neutral).


{ WARNING Shifting the transfer case to N (Neutral) can cause the vehicle to roll even if the transmission is in P (Park). You or someone else could be seriously injured. Be sure to set the parking brake before placing the transfer case in N (Neutral). See Parking Brake on page 9‑54.


. Shifting into Four-Wheel Drive Low with the vehicle at a stop may be more difficult. You may be unable to complete the shift to Four-Wheel Drive Low, and


the transfer case will end up in N (Neutral). This is normal, and is a function of the gear teeth aligning in the transfer case. When this happens, make sure the engine is on, shift the transmission momentarily to D (Drive) and back to N (Neutral), and then complete the transfer case shift.


. Shift the transfer case shift lever


in one continuous motion into the Four-Wheel Drive Low position.


. When in Four-Wheel Drive Low


do not drive faster than 72 km/h (45 mph). This will reduce wear and extend the life of your transfer case.


Shifting In or Out of Neutral 1. With the vehicle running and the engine at an idle, set the parking brake.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (45,1)


2. Place the transmission into


N (Neutral).


Shift the transfer case in one continuous motion into or out of the N (Neutral) position. Electronic Transfer Case


The transfer case knob is located next to the steering column. Use the dial to shift into and out of four-wheel drive.


Driving and Operating


9-45


Recommended Transfer Case Settings


Driving Conditions


Normal Severe Extreme


Vehicle in Tow*


Transfer Case Settings


4m


4n


2m


YES


YES


YES


YES


*See Recreational Vehicle Towing on page 10‑89 or Towing the Vehicle on page 10‑89.


You can choose among four driving settings: Indicator lights in the dial show which setting you are in. The indicator lights will come on briefly when you turn on the ignition and one will stay on. If the lights do not come on, you should take the vehicle to your dealer for service. An indicator light flashes while shifting the transfer case and remains illuminated when the shift is complete. If for some reason the


transfer case cannot make a requested shift, it will return to the last chosen setting. 2 m (Two-Wheel Drive High): This setting is used for driving in most street and highway situations. The front axle is not engaged in Two-Wheel Drive. This setting also provides the best fuel economy. 4 m (Four-Wheel Drive High): Use the Four-Wheel Drive High position when extra traction is needed, such


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (46,1)


9-46


Driving and Operating


as on snowy or icy roads or in most off-road situations. This setting also engages the front axle to help drive the vehicle. This is the best setting to use when plowing snow. 4 n (Four-Wheel Drive Low): This setting also engages the front axle and delivers extra torque. You may never need this setting. It sends maximum power to all four wheels. You might choose Four-Wheel Drive Low while driving off-road in deep sand, deep mud, deep snow, and while climbing or descending steep hills. If the vehicle has StabiliTrak®, shifting into Four-Wheel Drive Low will turn Traction Control and StabiliTrak off. See StabiliTrak® System on page 9‑56.


{ WARNING Shifting the transfer case to N (Neutral) can cause the vehicle to roll even if the transmission is


(Continued)


WARNING (Continued)


in P (Park). You or someone else could be seriously injured. Be sure to set the parking brake before placing the transfer case in N (Neutral). See Parking Brake on page 9‑54.


N (Neutral): Shift the vehicle's transfer case to N (Neutral) only when towing the vehicle. See Recreational Vehicle Towing on page 10‑89 or Towing the Vehicle on page 10‑89 for more information. If the SERVICE 4 WHEEL DRIVE message stays on, you should take the vehicle to your dealer for service. See “SERVICE 4 WHEEL DRIVE” under Transmission Messages on page 5‑44.


Shifting Into Two-Wheel Drive High Turn the knob to the Two-Wheel Drive High position. This can be done at any speed, except when


shifting from Four-Wheel Drive Low. See “Shifting Out of Four-Wheel Drive Low” for more information.


Shifting Into Four-Wheel Drive Low When Four-Wheel Drive Low is engaged, vehicle speed should be kept below 72 km/h (45 mph). Extended high-speed operation in Four-Wheel Drive Low may damage or shorten the life of the drivetrain. To shift to the Four-Wheel Drive Low position, the ignition must be in ON/RUN and the vehicle must be stopped or moving less than 5 km/h (3 mph) with the transmission in N (Neutral). The preferred method for shifting into Four-Wheel Drive Low is to have the vehicle moving 1.6 to 3.2 km/h (1 to 2 mph). Turn the knob to the Four-Wheel Drive Low position. You must wait for the Four-Wheel Drive Low indicator light to stop flashing and remain on before shifting the transmission in gear.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (47,1)


Notice: Shifting the transmission into gear before the requested mode indicator light has stopped flashing could damage the transfer case. To help avoid damaging the vehicle, always wait for the mode indicator lights to stop flashing before shifting the transmission into gear. It is typical for the vehicle to exhibit significant engagement noise and bump when shifting between Four-Wheel Drive Low and Four-Wheel Drive High ranges or from transfer case N (Neutral) with the engine running. If the knob is turned to the Four-Wheel Drive Low position when the vehicle is in gear and/or moving more than 5 km/h (3 mph), the Four-Wheel Drive Low indicator light will flash for 30 seconds and not complete the shift. After 30 seconds the transfer case will shift to Four-Wheel Drive High mode. With the vehicle moving


less than 5 km/h (3 mph), and the transmission in N (Neutral), attempt the shift again.


Shifting Out of Four-Wheel Drive Low To shift from Four-Wheel Drive Low to Four-Wheel Drive High, or Two-Wheel Drive High, the vehicle must be stopped or moving less than 5 km/h (3 mph) with the transmission in N (Neutral) and the ignition in ON/RUN. The preferred method for shifting out of Four-Wheel Drive Low is to have the vehicle moving 1.6 to 3.2 km/h (1 to 2 mph). Turn the knob to the Four-Wheel Drive High or Two-Wheel Drive High position. You must wait for the Four-Wheel Drive High or Two-Wheel Drive High indicator light to stop flashing and remain on before shifting the transmission into gear. Notice: Shifting the transmission into gear before the requested mode indicator light has stopped flashing could damage the


Driving and Operating


9-47


transfer case. To help avoid damaging the vehicle, always wait for the mode indicator lights to stop flashing before shifting the transmission into gear. It is typical for the vehicle to exhibit significant engagement noise and bump when shifting between Four-Wheel Drive Low and Four-Wheel Drive High ranges or from transfer case N (Neutral) with the engine running. If the knob is turned to the Four-Wheel Drive High, or Two-Wheel Drive High switch position when the vehicle is in gear and/or moving more than 5 km/h (3 mph), the Four-Wheel Drive High, AUTO, or Two-Wheel Drive High indicator light will flash for 30 seconds but will not complete the shift. With the vehicle moving less than 5 km/h (3 mph), and the transmission in N (Neutral), attempt the shift again.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (48,1)


9-48


Driving and Operating


Shifting into Neutral To shift the transfer case to N (Neutral) do the following: 1. Make sure the vehicle is parked


so that it will not roll.


2. Set the parking brake and press


and hold the regular brake pedal. See Parking Brake on page 9‑54 for more information.


3. Start the vehicle or turn the


ignition to ON/RUN.


4. Shift the transmission to


N (Neutral).


5. Shift the transfer case to


Two-Wheel Drive High.


6. Turn the transfer case dial


clockwise to N (Neutral) until it stops and hold it there until the Neutral light starts blinking. This will take at least 10 seconds. Then slowly release the dial to the four low position. The N (Neutral) light will come on when the transfer case shift to N (Neutral) is complete.


7.


If the engine is running, verify that the transfer case is in N (Neutral) by shifting the transmission to R (Reverse) for one second, then shift the transmission to D (Drive) for one second.


8. Turn the ignition to ACC/


ACCESSORY, which will turn the engine off.


9. Place the transmission shift


lever in P (Park).


10. Release the parking brake prior


to moving the vehicle.


11. Turn the ignition to LOCK/OFF.


Shifting Out of Neutral To shift the transfer case out of N (Neutral) do the following: 1. Set the parking brake and apply


the regular brake pedal.


2. Turn the ignition to ON/RUN with


the engine off, and shift the transmission to N (Neutral).


3. Turn the transfer case dial to


Two-Wheel Drive High. After the transfer case has shifted out of N (Neutral), the N (Neutral) light will go out.


4. Release the parking brake prior


to moving the vehicle.


Notice: Shifting the transmission into gear before the requested mode indicator light has stopped flashing could damage the transfer case. To help avoid damaging the vehicle, always wait for the mode indicator lights to stop flashing before shifting the transmission into gear. 5. Start the engine and shift the


transmission to the desired position.


Excessively shifting the transfer case into or out of the different modes may cause the transfer case to enter the shift protection mode. This will protect the transfer case from possible damage and will only allow the transfer case to respond to


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (49,1)


one shift per 10 seconds. The transfer case may stay in this mode for up to three minutes. Automatic Transfer Case


The transfer case knob is located next to the steering column. Use the dial to shift into and out of Four-Wheel Drive. You can choose among five driving settings: Indicator lights in the dial show which setting you are in. The indicator lights will come on briefly


Driving and Operating


9-49


when you turn on the ignition and one will stay on. If the lights do not come on, you should take the vehicle to your dealer for service. An indicator light will flash while shifting the transfer case. It will remain illuminated when the shift is complete. If for some reason the transfer case cannot make a requested shift, it will return to the last chosen setting. 2 m (Two-Wheel Drive High): This setting is used for driving in most street and highway situations. The front axle is not engaged in Two-Wheel Drive. This setting also provides the best fuel economy. AUTO (Automatic Four-Wheel Drive): This setting is ideal for use when road surface traction conditions are variable. When driving the vehicle in AUTO, the front axle is engaged, but the vehicle's power is sent only to the front and rear wheels automatically based on driving conditions. Driving


in this mode results in slightly lower fuel economy than Two-Wheel Drive High. 4 m (Four-Wheel Drive High): Use the Four-Wheel Drive High position when extra traction is needed, such as on snowy or icy roads or in most off-road situations. This setting also engages the front axle to help drive the vehicle. This is the best setting to use when plowing snow. 4 n (Four-Wheel Drive Low): This setting also engages the front axle and delivers extra torque. You may never need this setting. It sends maximum power to all four wheels. You might choose Four-Wheel Drive Low if you are driving off-road in deep sand, deep mud, deep snow, and while climbing or descending steep hills. If the vehicle has StabiliTrak®, shifting into Four-Wheel Drive Low will turn Traction Control and StabiliTrak off. See StabiliTrak® System on page 9‑56.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (50,1)


9-50


Driving and Operating


{ WARNING Shifting the transfer case to N (Neutral) can cause the vehicle to roll even if the transmission is in P (Park). You or someone else could be seriously injured. Be sure to set the parking brake before placing the transfer case in N (Neutral). See Parking Brake on page 9‑54.


N (Neutral): Shift the vehicle's transfer case to N (Neutral) only when towing the vehicle. See Recreational Vehicle Towing on page 10‑89 or Towing the Vehicle on page 10‑89 for more information. If the SERVICE 4 WHEEL DRIVE message stays on, you should take the vehicle to your dealer for service. See “SERVICE 4 WHEEL DRIVE” under Transmission Messages on page 5‑44.


Shifting Into Four-Wheel Drive High or AUTO (Automatic Four-Wheel Drive) Turn the knob to the Four-Wheel Drive High or AUTO position. This can be done at any speed, except when shifting from Four-Wheel Drive Low. The indicator light will flash while shifting. It will remain on when the shift is completed.


Shifting Into Two-Wheel Drive High Turn the knob to the Two-Wheel Drive High position. This can be done at any speed, except when shifting from Four-Wheel Drive Low. The indicator light will flash while shifting. It will remain on when the shift is completed.


Shifting Into Four-Wheel Drive Low When Four-Wheel Drive Low is engaged, vehicle speed should be kept below 72 km/h (45 mph).


Extended high-speed operation in Four-Wheel Drive Low may damage or shorten the life of the drivetrain. To shift to the Four-Wheel Drive Low position, the ignition must be in ON/RUN and the vehicle must be stopped or moving less than 5 km/h (3 mph) with the transmission in N (Neutral). The preferred method for shifting into Four-Wheel Drive Low is to have the vehicle moving 1.6 to 3.2 km/h (1 to 2 mph). Turn the knob to the Four-Wheel Drive Low position. You must wait for the Four-Wheel Drive Low indicator light to stop flashing and remain on before shifting the transmission into gear. Notice: Shifting the transmission into gear before the requested mode indicator light has stopped flashing could damage the transfer case. To help avoid damaging the vehicle, always wait for the mode indicator lights to stop flashing before shifting the transmission into gear.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (51,1)


Driving and Operating


9-51


It is typical for the vehicle to exhibit significant engagement noise and bump when shifting between Four-Wheel Drive Low and Four-Wheel Drive High ranges or from N (Neutral) with the engine running. If the knob is turned to the Four-Wheel Drive Low position when the vehicle is in gear and/or moving more than 5 km/h (3 mph), the Four-Wheel Drive Low indicator light will flash for 30 seconds and not complete the shift. After 30 seconds the transfer case will shift to Four-Wheel Drive High mode. With the vehicle moving less than 5 km/h (3 mph), and the transmission in N (Neutral), attempt the shift again.


Shifting Out of Four-Wheel Drive Low To shift from Four-Wheel Drive Low to Four-Wheel Drive High, AUTO or Two-Wheel Drive High, the vehicle must be stopped or moving less than 5 km/h (3 mph) with the


transmission in N (Neutral) and the ignition in ON/RUN. The preferred method for shifting out of Four-Wheel Drive Low is to have the vehicle moving 1.6 to 3.2 km/h (1 to 2 mph). Turn the knob to the Four-Wheel Drive High, AUTO or Two-Wheel Drive High position. You must wait for the Four-Wheel Drive High, AUTO or Two-Wheel Drive High indicator light to stop flashing and remain on before shifting the transmission into gear. Notice: Shifting the transmission into gear before the requested mode indicator light has stopped flashing could damage the transfer case. To help avoid damaging the vehicle, always wait for the mode indicator lights to stop flashing before shifting the transmission into gear. It is typical for the vehicle to exhibit significant engagement noise and bump when shifting between Four-Wheel Drive Low and


Four-Wheel Drive High ranges or from N (Neutral) with the engine running. If the knob is turned to the Four-Wheel Drive High, AUTO, or Two-Wheel Drive High switch position when the vehicle is in gear and/or moving more than 5 km/h (3 mph), the Four-Wheel Drive High, AUTO or Two-Wheel Drive High indicator light will flash for 30 seconds but will not complete the shift. With the vehicle moving less than 5 km/h (3 mph), and the transmission in N (Neutral), attempt the shift again.


Shifting into Neutral To shift the transfer case to N (Neutral) do the following: 1. Make sure the vehicle is parked


so that it will not roll.


2. Set the parking brake and apply


the regular brake pedal. See Parking Brake on page 9‑54 for more information.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (52,1)


Notice: Shifting the transmission into gear before the requested mode indicator light has stopped flashing could damage the transfer case. To help avoid damaging the vehicle, always wait for the mode indicator lights to stop flashing before shifting the transmission into gear. 5. Start the engine and shift the


transmission to the desired position.


9-52


Driving and Operating


3. Start the vehicle or turn the


9. Place the transmission shift


ignition in ON/RUN.


lever in P (Park).


4. Put the transmission in


10. Release the parking brake prior


N (Neutral).


to moving the vehicle.


5. Shift the transfer case to


Two-Wheel Drive High.


6. Turn the transfer case dial


clockwise to N (Neutral) until it stops and hold it there until the N (Neutral) light starts blinking. This will take at least 10 seconds. Then slowly release the dial to the four low position. The N (Neutral) light will come on when the transfer case shift to N (Neutral) is complete. If the engine is running, make sure that the transfer case is in N (Neutral) by shifting the transmission to R (Reverse) for one second, then shift the transmission to D (Drive) for one second.


7.


8. Turn the ignition to ACC/


ACCESSORY, which will turn the engine off.


11. Turn the ignition to LOCK/OFF.


Shifting Out of Neutral To shift out of N (Neutral) do the following: 1. Set the parking brake and apply


the regular brake pedal.


2. Turn the ignition to ON/RUN with


the engine off, and shift the transmission to N (Neutral).


3. Turn the transfer case dial to


Two-Wheel Drive High, Four-Wheel Drive High, or AUTO. After the transfer case has shifted out of N (Neutral), the N (Neutral) light will go out.


4. Release the parking brake prior


to moving the vehicle.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (53,1)


Brakes


Antilock Brake System (ABS) This vehicle might have the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on. This is normal.


If there is a problem with ABS, this warning light stays on. See Antilock Brake System (ABS) Warning Light on page 5‑24.


Driving and Operating


9-53


Along with ABS, the vehicle has a Dynamic Rear Proportioning (DRP) system. If there is a DRP problem, both the brake and ABS warning lights come on accompanied by a 10‐second chime. The lights and chime will come on each time the ignition is turned on until the problem is repaired. See your dealer for service. Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that the wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each front wheel and at both rear wheels. ABS can change the brake pressure to each wheel, as required, faster than any driver could. This can help the driver steer around the obstacle while braking hard.


As the brakes are applied, the computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, there will not be enough time to apply the brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS. Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let antilock work. You might feel the brakes vibrate or hear some noise, but this is normal. Braking in Emergencies If the vehicle has ABS, it allows the driver to steer and brake at the same time. However, if the vehicle does not have ABS, the first reaction, to hit the brake pedal hard


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (54,1)


9-54


Driving and Operating


and hold it down, might be the wrong thing to do. The wheels can stop rolling. Once they do, the vehicle cannot respond to the driver's steering. Momentum will carry it in whatever direction it was headed when the wheels stopped rolling. That could be off the road, into the very thing the driver was trying to avoid, or into traffic. If the vehicle does not have ABS, use a squeeze braking technique. This gives maximum braking while maintaining steering control. Do this by pushing on the brake pedal with steadily increasing pressure. In an emergency, you will probably want to squeeze the brakes hard without locking the wheels. If you hear or feel the wheels sliding, ease off the brake pedal. This helps retain steering control. With ABS, it is different. In many emergencies, steering can help more than even the very best braking.


Parking Brake


For vehicles with a release handle, set the parking brake by holding the regular brake pedal down, then pushing down the parking brake pedal. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 5‑24. A chime sounds and the warning light flashes when the parking brake is applied and the vehicle is moving at least 8 km/h (5 mph).


To release the parking brake, hold the regular brake pedal down. Then pull the bottom edge of the lever with the parking brake symbol, located above the parking brake pedal. If the ignition is on when the parking brake is released, the brake system warning light goes off. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and are parking on any hill, see Driving Characteristics and Towing Tips on page 9‑75.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (55,1)


Driving and Operating


9-55


brake is fully released and the brake warning light is off before driving. To release the parking brake, hold the regular brake pedal down, then push down momentarily on the parking brake pedal until you feel the pedal release. Slowly pull your foot up off the park brake pedal. If the parking brake is not released when you begin to drive, the brake system warning light will flash and a chime will sound warning you that the parking brake is still on. If you are towing a trailer and are parking on a hill, see Driving Characteristics and Towing Tips on page 9‑75.


Brake Assist If this vehicle has StabiliTrak®, it also has a Brake Assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions. This feature uses the stability system hydraulic brake


control module to supplement the power brake system under conditions where the driver has quickly and forcefully applied the brake pedal in an attempt to quickly stop or slow down the vehicle. The stability system hydraulic brake control module increases brake pressure at each corner of the vehicle until the ABS activates. Minor brake pedal pulsation or pedal movement during this time is normal and the driver should continue to apply the brake pedal as the driving situation dictates The Brake Assist feature will automatically disengage when the brake pedal is released or brake pedal pressure is quickly decreased.


Hill Start Assist (HSA) Non‐hybrid vehicles with StabiliTrak have a Hill Start Assist (HSA) feature, which may be useful when the vehicle is stopped on a grade. This feature is designed to prevent the vehicle from rolling, either


For vehicles without a release handle, set the parking brake by holding the regular brake pedal down, then pushing down the parking brake pedal. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 5‑24. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (56,1)


9-56


Driving and Operating


forward or rearward, during vehicle drive off. After the driver completely stops and holds the vehicle in a complete standstill on a grade, HSA will be automatically activated. During the transition period between when the driver releases the brake pedal and starts to accelerate to drive off on a grade, HSA holds the braking pressure for a maximum of two seconds to ensure that there is no rolling. The brakes will automatically release when the accelerator pedal is applied within the two‐second window. If the vehicle is equipped with the Integrated Trailer Brake Control (ITBC) system, HSA may also apply the trailer brakes. It will not activate if the vehicle is in a drive gear and facing downhill or if the vehicle is facing uphill and in R (Reverse). There may be situations on minor hills (less than 5% grade) with a loaded vehicle or while pulling a trailer where HSA will not activate.


Ride Control Systems


StabiliTrak® System The vehicle has a vehicle stability enhancement system called StabiliTrak. It is an advanced computer-controlled system that assists the driver with directional control of the vehicle in difficult driving conditions. StabiliTrak activates when the computer senses a discrepancy between the intended path and the direction the vehicle is actually traveling. StabiliTrak selectively applies braking pressure at any one of the vehicle's brakes to assist the driver with keeping the vehicle on the intended path. StabiliTrak is on automatically whenever the vehicle is started. To assist with directional control of the vehicle, the system should always be left on. Trailer Sway Control (TSC) is also on automatically when the vehicle is started. See Trailer Sway Control (TSC) on page 9‑104.


When the vehicle is started and begins to move, the system performs several diagnostic checks to insure there are no problems. The system may be heard or felt while it is working. This is normal and does not mean there is a problem with the vehicle. If cruise control is being used when StabiliTrak activates, the cruise control automatically disengages. The cruise control can be re-engaged when road conditions allow. See Cruise Control on page 9‑59. If the system fails to turn on or activate, the StabiliTrak light along with a message will be displayed on the Driver Information Center (DIC). If a DIC message appears, make sure the StabiliTrak system has not been turned off using the Traction Control System (TCS)/StabiliTrak button. Then turn the vehicle off, wait 15 seconds, and then turn it back on again to reset the system. If any of the messages still appear on the DIC, the vehicle should be


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (57,1)


Driving and Operating


9-57


taken in for service. For more information on the DIC messages, see Ride Control System Messages on page 5‑42.


The traction control part of StabiliTrak can be turned off by pressing and releasing the TCS/ StabiliTrak button if both systems (traction control and StabiliTrak) were previously on.


The StabiliTrak light will flash on the instrument panel cluster when the system or the TSC feature is both on and activated. The system may be heard or felt while it is working; this is normal.


The TCS/StabiliTrak button is located on the instrument panel.


To disable both TCS and StabiliTrak, press and hold the TCS/ StabiliTrak button until the StabiliTrak OFF light illuminates and the appropriate DIC message displays. This will also disable the TSC feature. Traction control and StabiliTrak can be turned on by pressing and releasing the TCS/StabiliTrak button if they are not automatically shut off for any other reason. This will also enable the TSC feature.


When the TCS or StabiliTrak system is turned off, the StabiliTrak light and the appropriate message will be displayed on the DIC to warn the driver. The vehicle will still have brake-traction control when traction control is off, but will not be able to use the engine speed management system. See “Traction Control Operation” next for more information. When the TCS has been turned off, system noises may still be heard as a result of the brake-traction control coming on. It is recommended to leave the system on for normal driving conditions, but it may be necessary to turn the system off if the vehicle is stuck in sand, mud, ice or snow, and you want to “rock” the vehicle to attempt to free it. It may also be necessary to turn off the system when driving in extreme off-road conditions where high wheel spin is required. See If the Vehicle Is Stuck on page 9‑14.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (58,1)


9-58


Driving and Operating


When the transfer case is in 4LO, the stability system is automatically disabled, the StabiliTrak light comes on, and the appropriate message will appear on the DIC. Both traction control and StabiliTrak are automatically disabled in this condition. Traction Control Operation The TCS is part of the StabiliTrak system. Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary. The TCS is enabled automatically when the vehicle is started. It will activate and the StabiliTrak light will flash if it senses that any of the wheels are spinning or beginning to lose traction while driving. If traction control is turned off, only the brake-traction control portion of traction control will work. The engine speed management will be


disabled. In this mode, engine power is not reduced automatically and the driven wheels can spin more freely. This can cause the brake-traction control to activate constantly. Notice: If the wheel(s) of one axle is allowed to spin excessively while the StabiliTrak®, ABS, brake warning lights, and any relevant DIC messages are displayed, the transfer case could be damaged. The repairs would not be covered by the vehicle warranty. Reduce engine power and do not spin the wheel(s) excessively while these lights and messages are displayed. The TCS may activate on dry or rough roads or under conditions such as heavy acceleration while turning or abrupt upshifts/downshifts of the transmission. When this happens, a reduction in acceleration may be noticed, or a noise or vibration may be heard. This is normal.


If cruise control is being used when the system activates, the StabiliTrak light will flash and cruise control will automatically disengage. Cruise control may be reengaged when road conditions allow. See Cruise Control on page 9‑59. StabiliTrak may also turn off automatically if it determines that a problem exists with the system. If the problem does not clear itself after restarting the vehicle, see your dealer for service. Vehicles with StabiliTrak have a Trailer Sway Control (TSC) feature. See Trailer Sway Control (TSC) on page 9‑104. Vehicles with StabiliTrak have a Hill Start Assist (HSA) feature. See Hill Start Assist (HSA) on page 9‑55. Adding non-dealer accessories can affect the vehicle's performance. See Accessories and Modifications on page 10‑3.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (59,1)


Locking Rear Axle Vehicles with a locking rear axle can give more traction on snow, mud, ice, sand, or gravel. It works like a standard axle most of the time, but when traction is low, this feature will allow the rear wheel with the most traction to move the vehicle.


Driving and Operating


9-59


For vehicles with an Allison or Hydra-Matic 6-speed automatic transmission, see “Grade Braking” under Tow/Haul Mode on page 9‑38
for an explanation of how cruise control interacts with the Range Selection Mode, tow/haul and grade braking systems. For vehicles with the StabiliTrak system that begins to limit wheel spin while you are using cruise control, the cruise control will automatically disengage. See StabiliTrak® System on page 9‑56. When road conditions allow the cruise control to be safely used again, it can be turned back on.


Cruise Control


{ WARNING


Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use the cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads.


For vehicles with cruise control, a speed of about 40 km/h (25 mph) or more can be maintained without keeping your foot on the accelerator. Cruise control does not work at speeds below about 40 km/h (25 mph). When the brakes are applied, cruise control is turned off.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (60,1)


9-60


Driving and Operating


[ (Cancel): Press to disengage cruise control without erasing the set speed from memory.


Setting Cruise Control If the cruise button is on when not in use, it could get bumped and go into cruise when not desired. Keep the cruise control switch off when cruise is not being used. The cruise control light on the instrument panel cluster will come on after the cruise control has been set to the desired speed. 1. Press I. 2. Get up to the desired speed. 3. Press the SET− button located


on the steering wheel and release it.


4. Take your foot off the


accelerator.


Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied, the cruise control is disengaged without erasing the set speed from memory. Once the vehicle speed reaches about 40 km/h (25 mph) or more, press the +RES button on the steering wheel. The vehicle returns to the previous set speed and stays there.


Increasing Speed While Using Cruise Control If the cruise control system is already activated, . Press and hold the +RES button


on the steering wheel until the desired speed is reached, then release it. To increase vehicle speed in small amounts, press the +RES button. Each time this is done, the vehicle goes about 1.6 km/h (1 mph) faster.


I (On/Off): Press to turn the system on or off. The indicator light is on when cruise control is on and turns off when cruise control is off. + RES (Resume/Accelerate): Press briefly to resume to a previously set speed, or press and hold to accelerate. SET − (Set/Coast): Press to set the speed and activate cruise control or make the vehicle decelerate.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (61,1)


Driving and Operating


9-61


To disable and enable Cruise Grade Braking for the current ignition key cycle, press and hold the Tow/Haul button for three seconds. A DIC message displays. See Transmission Messages on page 5‑44.


. Vehicles with a diesel engine


have Cruise Grade Braking enabled when Tow/Haul Mode is on, the exhaust brake is on, or both are on.


For other forms of Grade Braking, see Automatic Transmission on page 9‑33 andTow/Haul Mode on page 9‑38.


Reducing Speed While Using Cruise Control If the cruise control system is already activated, . Press and hold the SET– button


on the steering wheel until the desired lower speed is reached, then release it. To slow down in small amounts, press the SET– button on the steering wheel briefly. Each time this is done, the vehicle goes about 1.6 km/h (1 mph) slower.


Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle will slow down to the previous set cruise speed.


Using Cruise Control on Hills How well the cruise control works on hills depends on the vehicle speed, the load, and the steepness of the hills. When going up steep


hills, pressing the accelerator pedal may be necessary to maintain vehicle speed. While going downhill: . Vehicles with a four speed


automatic transmission may need to have the brakes applied or the transmission shifted to a lower gear to maintain driver selected speed.


. Vehicles with a six speed


automatic transmission and a gasoline engine have Cruise Grade Braking to help maintain driver selected speed. Cruise Grade Braking is enabled when the vehicle is started and Cruise Control is active. It is not enabled in Range Selection Mode. It assists in maintaining driver selected speed when driving on downhill grades by using the engine and transmission to slow the vehicle.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (62,1)


9-62


Driving and Operating


Ending Cruise Control There are three ways to end cruise control:


To disengage cruise control; step lightly on the brake pedal.


. Press [ on the steering wheel.


To turn off the cruise control, press I on the steering wheel.


Erasing Speed Memory The cruise control set speed is erased from memory by pressing I or if the ignition is turned off.


Object Detection Systems


Ultrasonic Parking Assist If available, the Ultrasonic Rear Parking Assist (URPA) system assists the driver with parking and avoiding objects while in R (Reverse). URPA operates at speeds less than 8 km/h (5 mph). The sensors on the rear bumper detect objects up to 2.5 m (8 ft) behind the vehicle, and at least 25 cm (10 in) off the ground. { WARNING


The URPA system does not detect children, pedestrians, bicyclists, animals, or objects below the bumper or that are too close or too far from the vehicle. It is not available at speeds greater than 8 km/h (5 mph). To prevent injury, death, or vehicle


(Continued)


WARNING (Continued)


damage, even with URPA, always check the area around the vehicle and check all mirrors before backing.


How the System Works URPA comes on automatically when the shift lever is moved into R (Reverse). A single tone sounds to indicate the system is working. URPA operates only at speeds less than 8 km/h (5 mph). An obstacle is indicated by audible beeps. The interval between the beeps becomes shorter as the vehicle gets closer to the obstacle. When the distance is less than 30 cm (12 in) the beeping is a continuous tone for five seconds. To be detected, objects must be at least 25 cm (10 in) off the ground and below tailgate level. Objects must also be within 2.5 m (8 ft) from


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (63,1)


the rear bumper. This distance may be less during warmer or humid weather. Turning the System On and Off The URPA system can be turned on and off using the rear park aid disable button located next to the radio.


The indicator light comes on when the system is disabled and turns off when the system is on. When the system is off, PARK ASSIST OFF displays on the Driver Information Center (DIC). The message disappears after a short period of time. URPA defaults to the on setting each time the vehicle is started.


Driving and Operating


9-63


Notice: If you use URPA while the tailgate is lowered, it may not detect an object behind your vehicle, and you might back into the object and damage your vehicle. Always verify the tailgate is closed when using URPA or turn off URPA when driving with the tailgate lowered. When the System Does Not Seem to Work Properly The following messages may be displayed on the DIC: SERVICE PARK ASSIST: message occurs, take the vehicle to your dealer to repair the system. PARK ASST BLOCKED SEE OWNERS MANUAL: This message can occur under the following conditions:


If this


The ultrasonic sensors are not clean. Keep the vehicle's rear bumper free of mud, dirt, snow, ice, and slush. For cleaning instructions, see Exterior Care on page 10‑93.


The park assist sensors are covered by frost or ice. Frost or ice can form around and behind the sensors and may not always be seen; this can occur after washing the vehicle in cold weather. The message may not clear until the frost or ice has melted.


. A trailer was attached to the


vehicle, or an object was hanging out of the tailgate during the last drive cycle. Once the object is removed and the tailgate is raised, URPA will return to normal operation. . A tow bar is attached to the


vehicle. The bumper is damaged. Take the vehicle to your dealer to repair the system.


. Other conditions, such as


vibrations from a jackhammer or the compression of air brakes on a very large truck, are affecting system performance.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (64,1)


9-64


Driving and Operating


Rear Vision Camera (RVC) If available, the Rear Vision Camera (RVC) system displays part of the scene behind the vehicle. { WARNING


The RVC system does not display children, pedestrians, bicyclists, animals, or any other object located outside the camera's field of view, below the bumper, or under the vehicle. Perceived distances may be different from actual distances. Do not back the vehicle using only the RVC screen, during longer, higher speed backing maneuvers, or where there could be cross traffic. Failure to use proper care before backing may result in injury, death, or vehicle damage. Always check behind and around the vehicle before backing.


Vehicles without Navigation System The RVC system displays a view of the area behind the vehicle. When the vehicle is on and shifted into R (Reverse) the video image appears on the inside rearview mirror. The video image disappears after the vehicle is shifted out of R (Reverse).


Turning the RVC System On or Off To turn off the RVC system, press and hold z , located on the inside rearview mirror, until the left indicator light turns off. The RVC display is now disabled. To turn the RVC system on, press and hold z until the left indicator light comes on. The RVC system display will appear in the mirror. Vehicles with Navigation System The RVC system is designed to help the driver when backing up by displaying a view of the area behind


the vehicle. When the vehicle is shifted into R (Reverse), the video image appears on the navigation screen. After a delay, the navigation screen displays the last screen after the vehicle is shifted out of R (Reverse).


Turning the RVC System On or Off To turn the RVC system on or off: 1. Shift into P (Park). 2. Press MENU to enter the


configure menu options. Turn the Multifunction knob until the Display feature is highlighted and press the Multifunction knob. Or press the Display screen button


3. Select the Rear Camera Options screen button. The Rear Camera Options screen displays.


4. Select the Video screen button.


When the Video screen button is highlighted the RVC system is on.


Chevrolet Silverado Owner Manual - 2013 - crc2 - 8/13/12


Black plate (65,1)


Driving and Operating


9-65


The delay after shifting out of R (Reverse) is approximately 10 seconds. The delay can be canceled by performing one of the following: . Pressing a hard key on the


navigation system.


. Shifting into P (Park). . Reaching a vehicle speed of


8 km/h (5 mph).


Symbols The navigation system may have a feature that allows for viewing parking assist symbols on the navigation screen while using the RVC. The Ultrasonic Rear Park Assist (URPA) system must not be disabled to use the caution symbols. If URPA has been disabled and the symbols have been turned on, the Rear Parking Assist Symbols Unavailable error message may display. See Ultrasonic Parking Assist on page 9‑62.


The symbols appear near objects detected by the URPA system. The symbol may cover the object when viewing the navigation screen. To turn the symbols on or off: 1. Make sure that URPA has not


been disabled.


2. Shift into P (Park).

Loading...
x