2013 Chevrolet Impala Owners Manual

their factory default settings. Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: RESTORE ALL (default): The customization features will be set to their factory default settings. DO NOT RESTORE: The customization features will not be set to their factory default settings.

Exiting the Feature Settings Menu The feature settings menu will be exited when any of the following occurs:

The vehicle is shifted out of P (Park). The vehicle is no longer in ON/RUN. The trip/fuel or vehicle information DIC buttons are pressed. The end of the feature settings menu is reached and exited. . A 40-second time period has

elapsed with no selection made.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (39,1)

Universal Remote System See Radio Frequency Statement on page 13‑15 for information regarding Part 15 of the Federal Communications Commission (FCC) rules and Industry Canada Standards RSS-GEN/210/220/310.

Universal Remote System Programming

This vehicle may have the Universal Home Remote System.

Instruments and Controls

5-39

This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use this system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the transmitter. Because of the steps involved, it may be helpful to have another person available to assist in programming the transmitter. Be sure to keep the original remote control transmitter for use in other vehicles, as well as for future programming. Only the original remote control transmitter is needed for Fixed Code programming. The programmed buttons should be erased when the vehicle is sold or

the lease ends. See “Erasing Universal Home Remote Buttons” in this section. Park the vehicle outside of the garage when programming a garage door. Be sure that people and objects are clear of the garage door or gate that is being programmed. Programming Universal Home Remote — Rolling Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (40,1)

5-40

Instruments and Controls

To program up to three devices: 1. From inside the vehicle, press the two outside buttons at the same time for one to two seconds, and immediately release them.

4.

should slowly blink. This button may need to be held for up to 20 seconds. Immediately, within one second, release the button when the garage door moves. The indicator light will blink rapidly until programming is complete.

5. Press and release the same

button again. The garage door should move, confirming that programming is successful and complete.

To program another Rolling Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1 through 5, choosing a different function button in Step 3
than what was used for the garage door opener. If these instructions do not work, the garage door opener is probably a Fixed Code unit. Follow the Programming instructions that follow for a Fixed Code garage door opener.

2.

3.

In the garage, locate the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button. After pressing this button, complete the following steps in less than 30 seconds. Immediately return to the vehicle. Press and hold the Universal Home Remote button that will be used to control the garage door until the garage door moves. The indicator light, above the selected button,

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (41,1)

Instruments and Controls

5-41

Programming Universal Home Remote — Fixed Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold before 1996 are Fixed Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting. Otherwise, the device will time out and the procedure will have to be repeated.

If there are a row of dip switches similar to the graphic above, the garage door opener is a Fixed Code unit. If you do not see a row of dip switches, return to the previous section for Programming Universal Home Remote – Rolling Code. Your hand-held transmitter can have between 8 to 12 dip switches depending on the brand of transmitter. The garage door opener receiver (motor head unit) could also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head and hand-held transmitter is different,

To program up to three devices: 1. To verify that the garage door opener is a Fixed Code unit, remove the battery cover on the hand held transmitter supplied by the manufacturer of the garage door opener motor.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (42,1)

5-42

Instruments and Controls

or if the dip switch settings are different, use the dip switch settings on the motor head unit to program the Universal Home Remote. The motor head dip switch settings can also be used when the original hand held transmitter is not available.

Example of Eight Dip Switches

with Two Positions

2. Write down the 8 to 12 switch

settings from left to right as follows:

When a switch is in the up position, write “Left.” When a switch is in the down position, write “Right.” If a switch is set between the up and down position, write “Middle.” The switch settings written down in Step 2 will now become the button strokes to be entered into the Universal Home Remote in Step 4. Be sure to enter the switch settings written down in Step 2, in order from left to right, into the Universal Home Remote, when completing Step 4.

Example of Eight Dip Switches

with Three Positions

The panel of switches might not appear exactly as they do in the examples above, but they should be similar. The switch positions on the hand-held transmitter could be labeled, as follows:

A switch in the up position could be labeled as “Up,” “+,” or “On.” A switch in the down position could be labeled as “Down,” “−,” or “Off.” A switch in the middle position could be labeled as “Middle,” “0,” or “Neutral.”

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (43,1)

3. From inside your vehicle, first

4. The indicator lights will blink

6. Press and hold the button that

Instruments and Controls

5-43

firmly press all three buttons at the same time for about three seconds. Release the buttons to put the Universal Home Remote into programming mode.

slowly. Enter each switch setting from Step 2 into your vehicle's Universal Home Remote. You will have two and one-half minutes to complete Step 4. Now press one button on the Universal Home Remote for each switch setting as follows: If you wrote “Left,” press the left button in the vehicle. If you wrote “Right,” press the right button in the vehicle. If you wrote “Middle,” press the middle button in the vehicle.

A. Left Button ("Up," "+,"

or "On.")

B. Middle Button ("Middle," "0,"

or "Neutral.")

C. Right Button ("Down," "-,"

or "Off.")

5. After entering all of the switch

positions, again, firmly press and release all three buttons at the same time. The indicator lights will turn on.

will be used to control the garage door until the garage door moves. The indicator light above the selected button should slowly blink. This button may need to be held for up to 55 seconds. Immediately release the button when the garage door moves. The indicator light will blink rapidly until programming is complete.

7.

8. Press and release the same

button again. The garage door should move, confirming that programming is successful and complete.

To program another Fixed Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1 through 8, choosing a different button in Step 6 than what was used for the garage door opener.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (44,1)

5-44

Instruments and Controls

Universal Remote System Operation Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted. Reprogramming Universal Home Remote Buttons Any of the three buttons can be reprogrammed by repeating the instructions.

Erasing Universal Home Remote Buttons The programmed buttons should be erased when the vehicle is sold or the lease ends. To erase either Rolling Code or Fixed Code on the Universal Home Remote device: 1. Press and hold the 2 outside buttons at the same time for approximately 20 seconds, until the indicator lights, located directly above the buttons, begin to blink rapidly.

2. Once the indicator lights begin to

blink, release both buttons. The codes from all buttons will be erased.

For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 13‑3.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (1,1)

Lighting

Exterior Lighting

Exterior Lamp Controls . . . . . . . . 6-1
Headlamp High/Low-Beam

Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2
Daytime Running Lamps

(DRL)/Automatic Headlamp System . . . . . . . . . . . . . . . . . . . . . . 6-2
Hazard Warning Flashers . . . . . 6-3
Turn and Lane-Change

Signals . . . . . . . . . . . . . . . . . . . . . . 6-4
Fog Lamps . . . . . . . . . . . . . . . . . . . . 6-4

Interior Lighting

Instrument Panel Illumination

Control . . . . . . . . . . . . . . . . . . . . . . 6-5
Courtesy Lamps . . . . . . . . . . . . . . 6-5
Dome Lamps . . . . . . . . . . . . . . . . . 6-5
Reading Lamps . . . . . . . . . . . . . . . 6-6

Lighting Features

Entry Lighting . . . . . . . . . . . . . . . . . 6-6
Delayed Entry Lighting . . . . . . . . 6-6
Delayed Exit Lighting . . . . . . . . . 6-7
Parade Dimming . . . . . . . . . . . . . . 6-7
Battery Load Management . . . . 6-7
Battery Power Protection . . . . . . 6-8

Lighting

6-1

Exterior Lighting

Exterior Lamp Controls

The exterior lamp control is on the instrument panel to the left of the steering wheel. There are four positions: O (Off): Turns off the automatic headlamps and Daytime Running Lamps (DRL). Turning the headlamp control to the off position again will turn the automatic headlamps or DRL back on. For vehicles first sold in Canada, the off position only works when the vehicle is shifted into the P (Park) position.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (2,1)

6-2

Lighting

AUTO (Automatic): Automatically turns on the headlamps at normal brightness, together with the following: . Parking Lamps

Instrument Panel Lights Taillamps License Plate Lamps

; (Parking Lamps): Turns on the parking lamps together with the following:

Instrument Panel Lights Taillamps License Plate Lamps

2 (Headlamps): Turns on the headlamps together with the following lamps listed below. When the headlamps are turned on while the vehicle is on, the headlamps will turn off automatically 10 minutes after the ignition is turned off. When the headlamps are turned on while the vehicle is off, the headlamps will stay on for 10 minutes before automatically turning off to prevent

the battery from being drained. Turn the headlamp control to off and then back to the headlamp on position to make the headlamps stay on for an additional 10 minutes. . Parking Lamps

Taillamps License Plate Lamps Instrument Panel Lights

# (Fog Lamps) (If Equipped): Turns on the fog lamps. See Fog Lamps on page 6‑4.

Headlamp High/ Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal lever away from you. This instrument cluster light 3
comes on if the high-beam lamps are turned on while the ignition is in ON/RUN.

To change the headlamps from high beam to low beam, pull the turn signal lever toward you.

Flash-to-Pass This feature is used to signal to the vehicle ahead that you want to pass. If the headlamps are off or in the low‐beam position, pull the turn signal lever toward you to momentarily switch to high beams. Release the lever to turn the high-beam headlamps off.

Daytime Running Lamps (DRL)/Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles first sold in Canada.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (3,1)

The DRL system makes the low-beam headlamps come on at a reduced brightness when the following conditions are met:

The ignition is in the ON/RUN position. The exterior lamps control is in AUTO. The engine is running.

When the DRL are on, the regular headlamps, taillamps, sidemarker, and other lamps are not on. The instrument panel and cluster are also not on. The headlamps automatically change from DRL to the regular headlamps depending on the darkness of the surroundings. The other lamps that come on with the headlamps will also come on. When it is bright enough outside, the headlamps go off and the DRL come on. The regular headlamp system should be turned on when needed.

Lighting

6-3

Hazard Warning Flashers

Do not cover the light sensor on top of the instrument panel because it works with the DRL. Lights On with Wipers If the windshield wipers are activated in daylight with the engine on, and the exterior lamp control is in AUTO, the headlamps, parking lamps, and other exterior lamps come on. The transition time for the lamps coming on varies based on wiper speed. When the wipers are not operating, these lamps turn off. Move the exterior lamp control to P or ; to disable this feature.

The hazard warning flashers let you warn others that you have a problem. The hazard warning flasher button is located on top of the steering column. | : Press to make the front and rear turn signal lamps flash on and off. Press the button again to turn the flashers off.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (4,1)

6-4

Lighting

When the hazard warning flashers are on, the turn signals will not work.

Turn and Lane-Change Signals

An arrow on the instrument panel cluster will flash in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn.

Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is completed. If the lever is briefly pressed and released, the turn signal flashes three times. The lever returns to its starting position whenever it is released. If after signaling a turn or lane change the arrow flashes rapidly or does not come on, a signal bulb might be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. See Fuses and Circuit Breakers on page 10‑27. Turn Signal On Chime If either one of the turn signals are left on and the vehicle has been driven more than 1.2 km (0.75 mile), a chime will sound.

Fog Lamps

# (Fog Lamps): For vehicles with fog lamps, the button is located on the exterior lamps control. The exterior lamps control is located on the instrument panel to the left of the steering column. The ignition must be in the ON/RUN position for the fog lamps to come on.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (5,1)

Lighting

6-5

Courtesy Lamps When a door is opened, the courtesy lamps automatically come on. They make it easy for you to enter and leave your vehicle. You can also manually turn these lamps on by fully turning the instrument panel brightness control clockwise. The reading lamps, located on the rearview mirror, can be turned on or off independent of the automatic courtesy lamps, when the doors are closed.

Dome Lamps

Interior Lighting

Instrument Panel Illumination Control

Press # to turn the fog lamps on or off. A light will come on in the instrument panel cluster. When the headlamps are changed to high beam, the fog lamps also go off. Some localities have laws that require the headlamps to be on along with the fog lamps.

D (Instrument Panel Brightness): This knob is located on the instrument panel to the left of the steering wheel. Push the knob in all the way until it extends out and then turn the knob clockwise or counterclockwise to brighten or dim the lights. Push the knob back in when finished.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (6,1)

6-6

Lighting

The center mounted dome lamp overhead comes on when a door is opened. This lamp can also be turned on by turning the instrument panel brightness control clockwise.

Reading Lamps

The vehicle has reading lamps that also act as the dome lamp. Press the button near each lamp to turn them on and off. Map Lamps The vehicle has map lamps on the rearview mirror. Press the button near each lamp on the mirror to turn the map lamps on and off.

Lighting Features

Entry Lighting For vehicles with courtesy lamps, they come on and stay on for a set time whenever the unlock symbol is pressed on the Remote Keyless Entry (RKE) transmitter. If a door is opened, the lamps stay on while it is open and then turn off automatically about 20 seconds after the door is closed. If the unlock symbol is pressed and no door is opened, the lamps turn off after about 20 seconds. Entry lighting includes a feature called theater dimming. With theater dimming, the lamps do not turn off at the end of the delay time. Instead, they slowly dim and then go out. The delay time is canceled if the ignition key is turned to ON/RUN or the power door lock switch is pressed. The lamps will dim right away.

When the ignition is on, illuminated entry is inactive, which means the courtesy lamps will not come on unless a door is opened.

Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after all the doors have been closed, the delayed entry lighting feature continues to work until one of the following occurs:

The ignition is in ON/RUN. The doors are locked.

. An illumination period of about

25 seconds has elapsed.

If during the illumination period a door is opened, the timed illumination period is canceled and the interior lamps remain on.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (7,1)

Delayed Exit Lighting This feature illuminates the interior for a period of time after the key is removed from the ignition. The ignition must be off for delayed exit lighting to work. When the key is removed, interior illumination activates and remains on until one of the following occurs:

The ignition is in ON/RUN. The power door locks are activated.

. An illumination period of 20 seconds has elapsed.

If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open.

Parade Dimming Parade mode automatically prohibits the dimming of the instrument panel displays during the daylight while the headlamps are on so that the displays are still able to be seen.

Battery Load Management The vehicle has Electric Power Management (EPM) that estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery's state of charge is low, the voltage is raised slightly to quickly bring the charge back up.

Lighting

6-7

When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gauge or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (8,1)

6-8

Lighting

EPM works to prevent excessive discharge of the battery. It does this by balancing the generator's output and the vehicle's electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as BATTERY SAVER ACTIVE. If this messages displays, it is recommended that the driver reduce the electrical loads as much as possible. See Driver Information Center (DIC) on page 5‑22.

Battery Power Protection This feature helps prevent the battery from being drained, if the interior courtesy lamps, reading/map lamps, visor vanity lamps, or trunk lamp are accidentally left on. If any of these lamps are left on, they automatically turn off after 10 minutes, if the ignition is off. The lamps will not come back on again until one of the following occurs:

The ignition is turned on. The exterior lamps control is turned off, then on again.

The headlamps will time out after 10 minutes, if they are manually turned on with the ignition on or off.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (1,1)

Infotainment System

Introduction

Infotainment . . . . . . . . . . . . . . . . . . . 7-1
Theft-Deterrent Feature . . . . . . . 7-2
Operation . . . . . . . . . . . . . . . . . . . . . 7-2

Radio

AM-FM Radio . . . . . . . . . . . . . . . . . 7-6
Satellite Radio . . . . . . . . . . . . . . . . 7-8
Radio Reception . . . . . . . . . . . . . 7-11
Backglass Antenna . . . . . . . . . . 7-12
Satellite Radio Antenna . . . . . . 7-13

Audio Players

CD Player . . . . . . . . . . . . . . . . . . . 7-13
Auxiliary Devices . . . . . . . . . . . . 7-18

Phone

Bluetooth . . . . . . . . . . . . . . . . . . . . 7-19

Introduction

Infotainment Determine which radio the vehicle has and read the following pages to become familiar with its features.

{ WARNING

Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to infotainment tasks while driving.

This system provides access to many audio and non-audio listings. To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: . Become familiar with the

operation and controls of the audio system.

Infotainment System 7-1

. Set up the tone, speaker

adjustments, and preset radio stations.

For more information, see Defensive Driving on page 9‑2. Notice: Contact your dealer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment. The vehicle has Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 9‑17 for more information.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (2,1)

7-2

Infotainment System

Theft-Deterrent Feature TheftLock® is designed to discourage theft of the vehicle's radio by learning a portion of the Vehicle Identification Number (VIN). The radio does not operate if it is stolen or moved to a different vehicle.

Operation

Radio with CD (Base)

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (3,1)

Infotainment System 7-3

Using the Radio O (Power/Volume): Press to turn the system on and off. Turn to increase or decrease the volume. 4 (Information): Press to switch the display between the radio station frequency and the time. While the ignition is off, press this button to display the time. Speed Compensated Volume (SCV): Radios with the Speed Compensated Volume (SCV) feature automatically adjust the radio volume to compensate for road and wind noise as the vehicle speeds up or slows down, so that the volume level is consistent. To activate SCV: 1. Set the radio volume to the

desired level.

2. Press MENU to display the radio

setup menu.

3. Press the softkey under the

AUTO VOLUM tab on the radio display.

Radio with CD (MP3)

The vehicle has one of these radios as its infotainment system.

Softkeys The Radio with CD (MP3) has six softkeys located below the radio display. Softkeys are used to control functions that appear on the radio display as tabs directly above the softkeys.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (4,1)

7-4

Infotainment System

4. Press the softkey under the

desired Speed Compensated Volume setting (OFF, Low, Med, or High) to select the level of radio volume compensation. The display times out after approximately 10 seconds. Each higher setting allows for more radio volume compensation at faster vehicle speeds.

Setting the Tone (Bass/Treble) Radio with CD To adjust the bass or treble: 1. Press the f knob until Bass or

Treble displays.

2. To adjust the setting, do one of

the following:

Turn the f knob. Press ¨ SEEK or © SEEK. Press \ FWD or s REV.

EQ (Equalization): Press this button to choose bass and treble equalization settings designed for different types of music. Selecting

MANUAL or changing bass or treble, returns the EQ to the manual bass and treble settings. Unique EQ settings can be saved for each source. Setting the Tone (Bass/ Midrange/Treble) Radio with CD (MP3) BASS/MID/TREB (Bass, Midrange, or Treble): To adjust the bass, midrange, or treble: 1. Press the f knob until the tone

control tabs display.

2. Highlight the desired tone

control tab by doing one of the following:

Press the f knob. Press the softkey under the desired tab.

3. Adjust the setting by doing one

of the following:

Turn the f knob clockwise or counterclockwise.

Press ¨ SEEK or © SEEK. Press \ FWD or s REV. If a station's frequency is weak or if there is static, decrease the treble. To quickly adjust bass, midrange, or treble to the middle position, press the softkey positioned under the BASS, MID, or TREB tab for more than two seconds. A beep sounds and the level adjusts to the middle position. To quickly adjust all tone and speaker controls to the middle position, press the f knob for more than two seconds until a beep sounds. EQ (Equalization): Press this button to choose bass and treble equalization settings designed for different types of music. Selecting MANUAL or changing bass or treble returns the EQ to the manual bass and treble settings. Unique EQ settings can be saved for each source.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (5,1)

Infotainment System 7-5

Radio Messages Calibration Error: Displays if the radio is no longer calibrated properly for the vehicle. The vehicle must be returned to your dealer for service. Loc or Locked: Displays when the TheftLock® system has activated. Take the vehicle to your dealer for service. If any error occurs repeatedly or if an error cannot be corrected, contact your dealer.

If the radio has a Bose® audio system, the EQ settings are either MANUAL or TALK. Adjusting the Speakers (Balance/Fade) Radio with CD To adjust the balance or fade:

1. Press the ` button or press the f knob until the speaker control label displays.

2. To adjust the setting, do one of

the following:

Turn the f knob. Press ¨ SEEK or © SEEK. Press \ FWD or s REV.

Adjusting the Speakers (Balance/Fade) Radio with CD (MP3) BAL/FADE (Balance/Fade): To adjust the balance or fade: 1. Press the f knob until the

speaker control tabs display.

2. Highlight the desired speaker

control tab by doing one of the following:

Press the f knob. Press the softkey under the desired tab.

3. Adjust the setting by doing one

of the following:

Turn the f knob clockwise or counterclockwise. Press ¨ SEEK or © SEEK. Press \ FWD or s REV.

To quickly adjust all speaker and tone controls to the middle position, press the f knob for more than two seconds. If the Rear Seat Audio (RSA) is turned on, the radio disables FADE and mutes the rear speakers.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (6,1)

7-6

Infotainment System

Radio

AM-FM Radio

Radio Data System (RDS) The radio may have RDS. The RDS feature is available for use only on FM stations that broadcast RDS information. This system relies upon receiving specific information from these stations and only works when the information is available. While the radio is tuned to an FM-RDS station, the station name or call letters display. In rare cases, a radio station could broadcast incorrect information that causes the radio features to work improperly. If this happens, contact the radio station. 4 (Information) (RDS Features): For vehicles with RDS features, press 4 to display additional text information related to the current FM-RDS station. If information is available, the song title information displays on the top line of the display and artist information

If

displays on the bottom line. When information is not available, “NO INFO” displays. Auto Text (RDS Features): additional information is available for the current song being played, Auto Text will automatically page/ scroll the information every three seconds above the FAV presets on the radio display. By default, Auto Text is enabled. To change the Auto Text setting: 1. Press MENU to display the radio

setup menu.

2. Press the softkey under AUTO

TXT tab on the radio display.

3. Press the softkey under the ON or OFF tab on the radio display. If 4 is pressed and the song title or artist information is longer than what can be displayed, the extra information will page every three seconds when Auto Text is activated.

Finding a Station BAND: Press to choose between FM1, FM2, AM, or XM™ (if equipped) on the Radio with CD (Base). Press to choose between FM, AM, XM (if equipped) on the Radio with CD (MP3). f (Tune): Turn to select radio stations. © SEEK: Press to seek or scan stations with a strong signal in the selected band.

To seek stations, press and release © SEEK to go to the previous station and stay there. To scan stations, press and hold © SEEK for a few seconds until the radio beeps once. The radio goes to a station, plays for a few seconds, then goes to the next station. Press © SEEK again to stop scanning. To scan preset stations in the selected band, press and hold © SEEK for four seconds until a

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (7,1)

double beep sounds. The radio goes to a stored preset, plays for a few seconds, then goes to the next stored preset. Press © SEEK again to stop scanning preset stations.

¨ SEEK: Press to seek or scan stations with a strong signal in the selected band.

To seek stations, press and release ¨ SEEK to go to the next station and stay there. To scan stations, press and hold ¨ SEEK for a few seconds until the radio beeps once. The radio goes to a station, plays for a few seconds, then goes to the next station. Press ¨ SEEK again to stop scanning. To scan preset stations in the selected band, press and hold ¨ SEEK for four seconds until a double beep sounds. The radio goes to a stored preset, plays for a few seconds, then goes to the

next stored preset. Press ¨ SEEK again to stop scanning preset stations.

Storing Radio Stations Drivers are encouraged to store radio station while the vehicle is parked. See Defensive Driving on page 9‑2. Tune to stored radio stations using the presets, favorites button, and steering wheel controls, if the vehicle has this feature. Radios that have a FAV button store radio stations as favorites, up to 36 stations can be programmed as favorites using the 6 softkeys below the radio station frequency tabs and by using the FAV button. Press the FAV button to go through up to 6 pages of favorites, each having 6 favorite stations available per page. Each page of favorites can contain any combination of AM, FM, or XM, if equipped, stations. Radios that do not have a FAV button store radio stations as presets, up to 18 stations (6 FM1,

Infotainment System 7-7

6 FM2, and 6 AM), can be programmed on the 6 numbered pushbuttons.

Storing a Radio Station as a Preset, Radio with CD (Base) Radios that have numbered pushbuttons store radio stations as presets. Up to 18 stations (6 FM1, 6 FM2, and 6 AM), can be programmed on the six numbered buttons. To store preset stations: 1. Tune to a radio station. 2. Press and hold one of the

6 numbered pushbuttons for 3 seconds until a beep sounds. 3. Repeat Steps 1 and 2 to store

additional radio stations.

Storing a Radio Station as a Favorite, Radio with CD (MP3) Radios that have a FAV button store radio stations as favorites. To store a station as a favorite: 1. Tune to a radio station.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (8,1)

7-8

Infotainment System

2. Press the FAV button to display the page where the station will be stored.

3. Press and hold one of the

6 softkeys until a beep sounds.

4. Repeat Steps 1 through 3 to

store additional radio stations.

The number of favorites pages can be set up using the MENU button. To set up the number of favorites pages: 1. Press the MENU button. 2. Press the softkey located below

the FAV 1-6 tab.

3. Select the number of favorites pages by pressing the softkey located below the displayed page numbers.

4. Press the FAV button, or let the menu time out, to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites.

Satellite Radio

SiriusXM® Satellite Radio Service SiriusXM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. SiriusXM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. A service fee is required to receive the XM service. If SiriusXM Service needs to be reactivated, the radio will display “No Subscription Please Renew” on channel XM1. For more information, contact SiriusXM at www.siriusxm.com or call 1-866-635-2349 (U.S.) and www.xmradio.ca or call 1-877-209-0079 (Canada). 4 (Information) (SiriusXM Satellite Radio Service): For vehicles with SiriusXM, press 4 to display additional text information related to the current SiriusXM channel. If information is available, the song

title information displays on the top line of the display and artist information displays on the bottom line. When information is not available, “NO INFO” displays. Auto Text (Satellite Radio Service): If additional information is available for the current song being played, Auto Text will automatically page/scroll the information every three seconds above the FAV presets on the radio display. By default, Auto Text is enabled. To change the Auto Text setting: 1. Press MENU to display the radio

setup menu.

2. Press the softkey under AUTO

TXT tab on the radio display.

3. Press the softkey under the ON or OFF tab on the radio display. If 4 is pressed and the song title or artist information is longer than what can be displayed, the extra information will page every three seconds when Auto Text is activated.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (9,1)

Finding an SiriusXM Channel BAND: Press to switch between AM, FM, or SiriusXM, if equipped. f (Tune): Turn to manually select a SiriusXM channel. © SEEK: Press to go to the previous SiriusXM channel.

To scan stations, press and hold © SEEK for a few seconds until the radio beeps once. The radio goes to a channel, plays for a few seconds, then goes to the next station. Press © SEEK again to stop scanning.

¨ SEEK: Press to go to the next SiriusXM channel.

To scan stations, press and hold ¨ SEEK for a few seconds until the radio beeps once. The radio goes to a station, plays for a few seconds, then goes to the next station. Press ¨ SEEK again to stop scanning.

s REV: Press to go to the previous SiriusXM category.

\ FWD: Press to go to the next SiriusXM category. Finding a Category (CAT) Channel To find SiriusXM channels in a category: 1. Press the CAT button to display

the category tabs. Continue pressing the CAT button until the desired category name displays.

Radios with CD and DVD can also navigate the category list by pressing the \ FWD or the s REV button.

2. Press either of the two softkeys below the desired category tab to immediately tune to the first SiriusXM station in that category. To go to the previous or next SiriusXM station in the selected category, do one of the following:

Turn the f knob.

Infotainment System 7-9

Press the softkey below the right or left arrows in the category tab. Press © SEEK or ¨ SEEK.

3. To exit the category search

mode, press the FAV button or BAND button to display the favorites again.

Adding and Removing Categories Categories cannot be added or removed while the vehicle is moving faster than 8 km/h (5 mph). To add or remove a category: 1. Press the MENU button. 2. Press the softkey located below

the SiriusXM CAT tab.

3. Turn the f knob to display the

category you want to add or remove.

4. Press the softkey located under

the Add or Remove tab. To restore all removed categories, press the softkey under the Restore All tab.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (10,1)

7-10

Infotainment System

5. Repeat the steps to remove

more categories.

Storing SiriusXM Channels Drivers are encouraged to store radio station while the vehicle is parked. See Defensive Driving on page 9‑2. Tune to stored radio stations using the presets, favorites button, and steering wheel controls, if the vehicle has this feature. Up to 36 stations can be programmed as favorites using the 6 softkeys below the radio station frequency tabs and by using the FAV button. Press the FAV button to go through up to 6 pages of favorites, each having 6 favorite stations available per page. Each page of favorites can contain any combination of AM, FM, or SiriusXM, if equipped, stations.

Storing an SiriusXM Channel as a Favorite To store a station as a favorite: 1. Tune to an SiriusXM channel.

2. Press the FAV button to display the page where the station will be stored.

3. Press and hold one of the

6 softkeys until a beep sounds.

4. Repeat Steps 1 through 3 to

store additional radio stations.

The number of favorites pages can be set up using the MENU button. To set up the number of favorites pages: 1. Press the MENU button. 2. Press the softkey located below

the FAV 1-6 tab.

3. Select the number of favorites pages by pressing the softkey located below the displayed page numbers.

4. Press the FAV button, or let the menu time out, to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites.

SiriusXM Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer's request, by calling 1-866-635-2349 (U.S.) and 1-877-209-0079 (Canada). XM Updating: The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds. No XM Signal: The system is functioning correctly, but the vehicle is in a location that is blocking the SiriusXM signal. When the vehicle is moved into an open area, the signal should return. Loading XM: The audio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly. Channel Off Air: This channel is not currently in service. Tune in to another channel.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (11,1)

Infotainment System 7-11

Channel Unauth: This channel is blocked or cannot be received with your SiriusXM subscription package. Channel Unavail: This previously assigned channel is no longer assigned. Tune to another station. If this station was one of the presets, choose another station for that preset button. No Artist Info: No artist information is available at this time on this channel. The system is working properly. No Title Info: No song title information is available at this time on this channel. The system is working properly. No CAT Info: No category information is available at this time on this channel. The system is working properly. No Information: No text or informational messages are available at this time on this channel. The system is working properly.

No Subscription Please Renew: SiriusXM subscription needs to be reactivated. Contact SiriusXM at www.siriusxm.com or call 1-866-635-2349 (U.S.) and www.xmradio.ca or call 1-877-209-0079 (Canada). CAT Not Found: There are no channels available for the selected category. The system is working properly. XM Theftlocked: The XM receiver in the vehicle could have previously been in another vehicle. For security purposes, XM receivers cannot be swapped between vehicles. If this message is received after having the vehicle serviced, check with your dealer. XM Radio ID: this message alternates with the SiriusXM Radio 8 digit radio ID label. This label is needed to activate the service.

If tuned to channel 0,

If this message

If this message is

Unknown: received when tuned to channel 0, there could be a receiver fault. Consult with your dealer. Check Antenna: does not clear within a short period of time, the receiver or antenna could have a fault. Consult with your dealer. Check XM Receivr: message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer. XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer.

If this

Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (12,1)

7-12

Infotainment System

interference or static, unplug the item from the accessory power outlet. AM The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. For better radio reception, most AM radio stations boost the power levels during the day, and then reduce these levels during the night. Static can also occur when things like storms and power lines interfere with radio reception. When this happens, try reducing the treble on the radio. FM Stereo FM signals only reach about 16 to 65 km (10 to 40 mi). Although the radio has a built-in electronic circuit that automatically works to reduce interference, some static can occur, especially around tall buildings or hills, causing the sound to fade in and out.

SiriusXM® Satellite Radio Service SiriusXM Satellite Radio Service gives digital radio reception from coast to coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out. In addition, traveling or standing under heavy foliage, bridges, garages, or tunnels may cause loss of the SiriusXM signal for a period of time. Cellular Phone Usage Cellular phone usage may cause interference with the vehicle's radio. This interference may occur when making or receiving phone calls, charging the phone's battery, or simply having the phone on. This interference causes an increased level of static while listening to the radio. If static is received while listening to the radio, unplug the cellular phone and turn it off.

Backglass Antenna The AM-FM antenna is integrated with the rear window defogger, located in the rear window. Make sure that the inside surface of the rear window is not scratched and that the lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception. For proper radio reception, the antenna connector needs to be properly attached to the post on the glass. If a cellular telephone antenna needs to be attached to the glass, make sure that the grid lines for the AM-FM antenna are not damaged. There is enough space between the grid lines to attach a cellular telephone antenna without interfering with radio reception. Notice: Using a razor blade or sharp object to clear the inside rear window can damage the rear window antenna and/or the rear window defogger. Repairs would

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (13,1)

not be covered by the vehicle warranty. Do not clear the inside rear window with sharp objects. Notice: Do not apply aftermarket glass tinting with metallic film. The metallic film in some tinting materials will interfere with or distort the incoming radio reception. Any damage caused to the backglass antenna due to metallic tinting materials will not be covered by the vehicle warranty.

Satellite Radio Antenna The XM Satellite Radio antenna is located on the roof of the vehicle. Keep the antenna clear of obstructions for clear radio reception. If the vehicle has a sunroof, the performance of the XM system (if equipped) may be affected if the sunroof is open.

Audio Players

CD Player Some CD players can play MP3
CD-R or CD-RW discs. See “MP3” later in this section for more information. The CD player can play the smaller 8 cm (3 in) single discs with an adapter ring. Care of the CD Player Do not add labels to a disc. It could get caught in the CD player. Use a marking pen to write on the top of the disc if a description is needed. Do not use CD lens cleaners. They could damage the CD player. Notice: If a label is added to a CD, more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs, the CD player could be damaged. While using the CD player, use only CDs in good condition without any label,

Infotainment System 7-13

load one CD at a time, and keep the CD player and the loading slot free of foreign materials, liquids, and debris. If an error displays, see “CD Messages” later in this section. Care of CDs Store a disc in its original case or a protective case and away from direct sunlight and dust. If the bottom of a disc is damaged it may not play properly or at all. Do not touch the bottom of a disc while handling it, pick it up by grasping the outer edges or the edge of the hole and the outer edge. If the surface of a disc is dirty, take a soft, lint‐free cloth or dampen a clean, soft cloth in a mild, neutral detergent solution mixed with water, and clean it. Make sure the wiping process starts from the center to the edge.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (14,1)

7-14

Infotainment System

Inserting a Disc Insert the disc partway into the slot, label side up. The player pulls it in and the disc begins playing. Use an adapter ring when playing the smaller 8 cm (3 in) discs. Smaller discs with the adapter ring are loaded the same way as a full-size disc. Ejecting a Disc Z EJECT: Press to eject the disc. If the disc is not removed after several seconds, the CD player automatically pulls the disc back in. Playing a CD When a CD is inserted into the player, the CD symbol displays. As each new track starts to play, the track number displays. If the ignition or radio is turned off when a CD is in the player, the CD stays in the player. If the ignition or radio is turned on when a CD is in

the player, the CD starts to play where it stopped, if it was the last selected audio source.

Buttons and Knobs The buttons and knobs on the radio control the following features. f (Tune): Turn to select tracks on the CD. © SEEK: Press to go to the start of the current track, if more than 10 seconds have played. Press and hold or press multiple times to continue moving backward through the tracks on the CD. ¨ SEEK: Press to go to the next track. Press and hold or press multiple times to continue moving forward through the tracks on the CD. s REV (Reverse): Press and hold to reverse playback quickly within a track. Sound is heard at a reduced volume and the elapsed time of the track displays. Release to resume playing the track.

\ FWD (Fast Forward): Press and hold to advance playback quickly within a track. Sound is heard at a reduced volume and the elapsed time of the track displays. Release to resume playing the track. 4 (Information): Press to display available additional information about the current track. BAND: Press to listen to the radio while a CD is playing. The CD remains inside the CD player. CD/AUX (CD/Auxiliary): Press to play a CD while listening to the radio or a portable audio device. Press this button again and the system automatically searches for an auxiliary input device, such as a portable audio player. If a portable audio player is not connected, No Aux Input Device Found may display.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (15,1)

Softkeys The six softkeys below the radio display are used to control functions that display as tabs. The softkeys below the radio display control the following features. RDM (Random): Tracks can be listened to in random, rather than sequential order. To use random: 1. Press the softkey below the

RDM tab until Random Current Disc displays.

2. Press the softkey again to turn

off random play.

contains both types of audio, the CD player reads all MP3 files first, then the uncompressed CD audio files.

Supported File and Folder Structure The radio supports: . Up to 50 folders. . Up to 8 folders in depth. . Up to 50 playlists. . Up to 255 files. . Playlists with an .m3u or .wpl

extension. Files with an .mp3 or .cda file extension.

MP3 Supported Files The Radio with CD (MP3) has the capability of playing an MP3 CD-R or CD-RW disc. The radio can also play discs that contain both uncompressed CD audio and MP3 files. When a disc

Root Directory The root directory is treated as a folder. Files are stored in the root directory when the disc or storage device does not contain folders. Files accessed from the root directory of a disc display as F1 ROOT.

Infotainment System 7-15

Empty Folder Folders that do not contain files are skipped, and the player advances to the next folder that contains files.

File Naming The song name that displays is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the file name without the file extension as the track name. Track names longer than 32
characters or 4 pages are shortened. The display does not show parts of words on the last page of text and the extension of the filename is not displayed.

Playlists Discs that have playlists that were created using WinAmp™, MusicMatch™, or Real Jukebox™ software can be accessed; however, there is no playlist editing capability using the radio. These playlists are treated as special folders containing compressed audio song files.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (16,1)

7-16

Infotainment System

Playing an MP3

Order of Play Tracks are played in the following order: . Play begins from the first track in

the first playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the first track of the first playlist.

. Play begins from the first track in

the first folder and continues sequentially through all tracks in each folder. When the last track of the last folder has played, play continues from the first track of the first folder.

When playback starts from a new folder, the new track name displays unless folder mode has been chosen as the default display, then the new folder name displays.

Buttons and Knobs The buttons and knobs on the radio control the following features. f (Tune): Turn to select MP3 files on the disc. © SEEK: Press to go to the start of the track, if more than 10 seconds have played. Press and hold or press multiple times to continue moving backward through tracks. ¨ SEEK: Press to go to the next track. Press and hold or press multiple times to continue moving forward through tracks. s REV (Reverse): Press and hold to reverse playback quickly. Sound is heard at a reduced volume and the elapsed time of the track displays. Release s REV to resume playing. \ FWD (Fast Forward): Press and hold to advance playback quickly. Sound is heard at a reduced

volume and the elapsed time of the track displays. Release \ FWD to resume playing. 4 (Information): Press to display available additional information about the current track. BAND: Press to listen to the radio while an MP3 disc is playing. The MP3 disc remains inside the CD player. CD/AUX (CD/Auxiliary): Press to play an MP3 disc while listening to the radio or a portable audio device. Press this button again and the system automatically searches for an auxiliary input device, such as a portable audio player. If a portable audio player is not connected, No Aux Input Device Found may display.

Softkeys The six softkeys below the radio display are used to control functions that display as tabs. The softkeys below the radio display control the following features.

Chevrolet Impala Owner Manual - 2013 - crc - 8/27/12

Black plate (17,1)

S c (Previous Folder): Press the softkey below S c to go to the first track in the previous folder. c T (Next Folder): Press the softkey below c T to go to the first track in the next folder. RDM (Random): MP3 files can be listened to on a CD in random, rather than sequential order. To use random: 1. Press the softkey under the

RDM tab until Random Current Disc displays to play songs from the current CD in random order. 2. Press the same softkey again to

turn off random play.

h (Music Navigator): Press the softkey below h to have the files played in order by artist or album. The player scans the disc to sort the files by artist and album ID3 tag information. It can take several minutes to scan the disc depending

on the number of files on the disc. The radio may begin playing while it is scanning in the background. When the scan is finished, the disc begins playing files in order by artist. The current artist playing is shown on the second line of the display. Once all songs by that artist are played, the player moves to the next artist in alphabetical order and begins playing files by that artist. To listen to files by another artist, press the softkey located below either arrow tab. The disc goes to the next or previous artist in alphabetical order. Continue pressing either softkey below the arrow tab until the desired artist displays. To change from playback by artist to playback by album: 1. Press the softkey located below

the Sort By tab.

2. Press one of the softkeys below

the Album tab from the sort screen.

Infotainment System 7-17

3. Press the softkey below the

Back tab to return to the main music navigator screen.

The album name displays on the second line between the arrows and songs from the current album begins to play. Once all songs from that album have played, the player moves to the next album in alphabetical order on the disc and begins playing MP3 files from that album. To exit music navigator mode, press the softkey below the Back tab to return to normal MP3 playback. CD Player Messages CHECK DISC: If an error message displays and/or the disc comes out, it could be for one of the following reasons: