2006 Chevrolet Impala Owners Manual

Download PDF Manual
Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. 2-3 (cid:127) (cid:127) (cid:127) (cid:127) At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: (cid:127) Check the distance. You may be too far from your vehicle. You may need to stand closer during rainy or snowy weather. (cid:127) Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again. (cid:127) Check to determine if battery replacement or resynchronization is necessary. See “Battery Replacement” and “Resynchronization” under Remote Keyless Entry System Operation on page 2-4. If you are still having trouble, see your dealer or a qualiﬁed technician for service. Remote Keyless Entry System Operation The vehicle’s doors can be locked and unlocked, and the trunk can be unlatched from about 3 feet (1 m) up to 65 feet (20 m) away with the remote keyless entry transmitter. If your vehicle has the remote start feature you can also start your vehicle with the remote keyless entry transmitter. Your remote keyless entry transmitter, with the remote start button, provides an increased range of 195 feet (60 m) away. However, the range may be less while the vehicle is running. As a result, you may need to be closer to your vehicle to turn it off than you were to turn it on. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry System on page 2-3. 2-4 (cid:127) See DIC Vehicle Customization on page 3-53 for additional information. Pressing the lock button may arm the content theft-deterrent system. See Content Theft-Deterrent on page 2-17. " (Unlock): Press the unlock button to unlock the driver’s door. If the button is pressed again within ﬁve seconds, all remaining doors will unlock. The interior lamps will come on and stay on for 20 seconds or until the ignition is turned on. If enabled through the DIC, the parking lamps will ﬂash once to indicate unlocking has occurred. See DIC Vehicle Customization on page 3-53. Pressing the unlock button on the remote keyless entry transmitter will disarm the content theft-deterrent system. See Content Theft-Deterrent on page 2-17. V (Remote Trunk Release): Press this button to release the trunk lid. The transaxle must be in PARK (P) for this feature to operate. L (Vehicle Locator/Panic Alarm): Press and release this button to locate your vehicle. The turn signal lamps will ﬂash and the horn will sound three times. Press and hold this button for more than two seconds to activate the panic alarm. The turn signal lamps will ﬂash and the horn will sound repeatedly for 30 seconds. The alarm will turn off when the ignition is moved to RUN or the alarm button is pressed again. The ignition must be in OFF for the panic alarm to work. 2-5 Remote Keyless Entry with Remote Start Remote Keyless Entry without Remote Start The following functions may be available if your vehicle has the remote keyless entry system: / (Remote Vehicle Start): If your vehicle has this feature, it may be started from outside the vehicle using the remote keyless entry transmitter. See “Remote Vehicle Start” following for more detailed information. Q (Lock): Press the lock button to lock all the doors. If enabled through the Driver Information Center (DIC), the parking lamps will ﬂash once to indicate locking has occurred. If enabled through the DIC, the horn will chirp when the lock button is pressed again within ﬁve seconds of the previous press of the lock button. Matching Transmitter(s) to Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your GM dealer. Remember to bring any additional transmitters so they can also be re-coded to match the new transmitter. Once your dealer has coded the new transmitter, the lost transmitter will not unlock your vehicle. The vehicle can have a maximum of eight transmitters matched to it. See Remote Key under DIC Operation and Displays on page 3-39. Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. You can tell the battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery. The REPLACE BATTERY IN REMOTE KEY message in the vehicle’s DIC will display if the remote keyless entry transmitter battery is low. See “REPLACE BATTERY IN REMOTE KEY” under DIC Warnings and Messages on page 3-45 for additional information. Notice: When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter. 2-6 3. Slide the new battery into the transmitter with the positive side of the battery facing down. Use a type CR2032 battery, or equivalent type. Make sure the cover is on tightly, so water will not get in. 4. Snap the front and the back of the transmitter together. To replace the battery in the remote keyless entry transmitter do the following: 1. Use a ﬂat object with a thin edge into the notch, located below the trunk release button, and separate the bottom half from the top half of the transmitter. 2. Remove the old battery, but do not use a metal object to do this. 5. Test the operation of the transmitter with the vehicle. Remote Vehicle Start Your vehicle may have a remote starting feature. This feature allows you to start the engine from outside of the vehicle. It may also start up the vehicle’s heating or air conditioning systems and rear window defogger. When the remote start system is active the vehicle will automatically regulate the inside temperature. Normal operation of the system will return after the key is turned to the RUN position. 2-7 If your vehicle has an outside temperature display, during remote start this feature allows the climate control system to default to a heating mode during colder outside temperatures and a cooling mode during warmer outside temperatures. If your vehicle does not have an outside temperature display, during remote start the climate control system will turn on at the setting the vehicle was set to when the vehicle was last turned off. Laws in some communities may restrict the use of remote starters. For example, requiring a person using remote start to have the vehicle in view when doing so. Check local regulations for any requirements on remote starting of vehicles. Do not use the remote start feature if your vehicle is low on fuel. Your vehicle may run out of fuel. Your remote keyless entry transmitter, with the remote start button, provides an increased range of operation. However, the range may be less while the vehicle is running. As a result, you may need to be closer to your vehicle to turn it off, than you were to turn it on. There are other conditions which can affect the performance of the transmitter, see Remote Keyless Entry System on page 2-3 for additional information. / (Remote Start): Press and release the lock button and then press and hold this button to use the remote start feature. 2-8 To start the vehicle using the remote start feature, do the following: 1. Aim the transmitter at the vehicle. 2. Press and release the transmitter’s lock button, then immediately press and hold the transmitter’s remote start button until the turn signal lights ﬂash or if the vehicle’s lights are not visible, press and hold the remote start button for at least four seconds. The vehicle’s doors will lock. Pressing the remote start button again after the vehicle has started will turn off the ignition. 3. When the vehicle starts, the parking lamps will turn on and remain on while the vehicle is running. 4. If it is your ﬁrst remote start since last driving, repeat these steps while the engine is still running for a 10 minute time extension. Remote start can be extended two times. When you enter the vehicle during a remote start, and the engine is still running, turn the key to the RUN position to drive the vehicle. If the vehicle is left running it will automatically shut off after 10 minutes unless a time extension has been done. To manually shut off a remote start, do any of the following: (cid:127) Aim the remote keyless entry transmitter at the vehicle and press the remote start button until the parking lamps turn off. Turn on the hazards warning ﬂashers. Turn the ignition switch on and then off. The remote vehicle start feature provides two separate starts, each with 10 minutes of engine running, or it provides one start with 10 minutes of engine running that may be extended with 10 more minutes. If you press and release the transmitter lock button and then press and hold the remote start button, on the remote keyless entry transmitter, again before the ﬁrst 10 minutes of engine running time has expired, 10 minutes are added to the remaining minutes. For example, if the lock button and then the remote start buttons are pressed again after ﬁve minutes of the engine run time, 10 minutes are added and you now have 15 minutes of engine running. The added ten minutes are considered a second remote vehicle start. Once two remote starts or a single start with a time extension have been provided, the vehicle must be started normally with the ignition key to get more remote vehicle starts. The remote vehicle start feature will not operate if the key is in the ignition, the hood is not closed or if there is an emission control system malfunction. Also, the engine will turn off during a remote vehicle start if the coolant temperature gets too high or if the oil pressure gets low. Vehicles equipped with the remote vehicle start feature are shipped from the factory with the remote vehicle start system enabled. The system may be enabled or disabled through the DIC. See “REMOTE START” under DIC Vehicle Customization on page 3-53 for additional information. Remote Start Ready If your vehicle does not have the remote vehicle start feature, it may have the remote start ready feature. This feature allows your dealer to add the manufacturer’s remote vehicle start feature. If your vehicle has the remote start ready feature, your remote keyless entry transmitter will have extended range that will allow you to lock or unlock your vehicle from approximately 195 feet (60 m) away. See your dealer if you would like to add the manufacturer’s remote vehicle start feature to your vehicle. 2-9 (cid:127) (cid:127) There are several ways to lock and unlock your vehicle. From the outside, use your key in the driver’s door or use the remote keyless entry transmitter. From the inside, use the manual or power door locks. To unlock the driver’s side door from the outside with the key, insert the key and turn it counterclockwise. To lock the driver’s side door from the outside with your key, insert the key and turn it clockwise. To lock the door from the inside, push the manual lock knob down. To unlock the door, pull the knob up. Doors and Locks Door Locks {CAUTION: Unlocked doors can be dangerous. (cid:127) Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive. (cid:127) Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it. (cid:127) Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. 2-10 Power Door Locks A power door lock switch is located on both front doors next to the door handle. Press the top of the switch to unlock all doors, or press the bottom of the switch to lock all doors. If your vehicle has the optional content theft-deterrent system and it is armed, the power door lock switches will be disabled. You must use your remote keyless entry transmitter or your key to unlock the doors when the system is armed. See Content Theft-Deterrent on page 2-17. Automatic Door Lock The doors will automatically lock when the shift lever is moved out of PARK (P). The automatic door locking feature cannot be disabled. Programmable Automatic Door Unlock Your vehicle is programmed so that when the shift lever is moved into PARK (P) all doors will unlock. With the vehicle stopped and the engine running, door unlocking can be programmed through prompts displayed on the Driver Information Center (DIC). These prompts allow the driver to choose various unlock settings. For programming information, see DIC Vehicle Customization on page 3-53. 2-11 Rear Door Security Locks Your vehicle has rear door security locks that prevent passengers from opening the rear doors from the inside. The rear door security locks are located on the inside edge of each rear door. You must open the rear doors to access them. When you want to open a rear door when the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter, if equipped, the power door lock switch, or by lifting the rear door manual lock. 2. Open the door from the outside. To cancel the rear door security lock, do the following: 1. Unlock the door and open it from the outside. 2. Insert the key into the security lock slot and turn it so the slot is in the vertical position. To set the locks, do the following: 1. Insert the key into the security lock slot and turn it so the slot is in the horizontal position. 2. Close the door. 2-12 Lockout Protection This feature helps prevent you from locking the doors while your key is in the ignition. Always remember to take your key with you when exiting your vehicle. If the lock switch is pressed on the door that is open and the key is in the ignition, all of the doors will lock and then the driver’s door will unlock. A chime will sound continuously until all doors are closed. Trunk {CAUTION: It can be dangerous to drive with the trunk lid open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the trunk lid: (cid:127) Make sure all other windows are shut. (cid:127) Turn the fan on your heating or cooling system to its highest speed and select the control setting that will force outside air into your vehicle. See Climate Control System. If you have air outlets on or under the instrument panel, open them all the way. See Engine Exhaust on page 2-31. 2-13 (cid:127) Emergency Trunk Release Handle Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk as it could damage the handle. The emergency trunk release handle is only intended to aid a person trapped in a latched trunk, enabling them to open the trunk from the inside. Trunk Release To open the trunk from the outside, press the open trunk button on the remote keyless entry transmitter. Remote Trunk Release You can also open the trunk from inside the vehicle. G (Remote Trunk Release): Press the button with the open trunk symbol on it. The button is located next to the exterior lamps control on the left side of the instrument panel. The shift lever must be in PARK (P) for the remote trunk release button to work. If your vehicle ever loses power, you can open the trunk by lowering the rear seat and pulling the emergency trunk release handle located inside the trunk. See Split Folding Rear Seat on page 1-8 and “Emergency Trunk Release Handle” following. There is a glow-in-the-dark trunk release handle located on the latch inside the trunk. This handle will glow following exposure to light. Pull the release handle to open the trunk from the inside. 2-14 Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 2-15 Express-Down Window The driver’s window switch has an express-down feature labeled AUTO. This allows you to lower the window completely without holding the switch. Press the front of the switch to the second position and release. To stop the window while it is lowering, brieﬂy pull up on the switch. Window Lockout o (Window Lockout): The driver’s window switches also include a lockout switch. Press the right side of the switch to prevent the rear passengers from using their window switches. The driver can still control all the windows and the front passenger can control their own window with the lockout on. Press the left side of the switch to return to normal window operation. A visible red bar on the right side of the switch indicates that the lockout is off. Power Windows The switches on the driver’s door armrest are used to control each of the windows. The power window switches work while the ignition is in RUN, ACCESSORY, or while Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-22. Each passenger door has its own window switch. To lower the window, press and hold the front of the switch to the ﬁrst position until the window is at the desired level. To raise the window, pull up and hold the front of the switch. 2-16 Sun Visors To block out glare, swing down the sun visors. They can be detached from the center retainer and slid along the rod to cover different areas of the front window and rotated to cover the side windows. Visor Vanity Mirror Swing down the sun visors and lift the cover to expose the vanity mirror. Do not drive with the cover lifted due to possible glare impeding other drivers behind or to the side of the vehicle. Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Content Theft-Deterrent Your vehicle may have the optional content theft-deterrent alarm system. To activate the theft-deterrent system: 1. Open the door. 2. Lock the door with the power door lock switch or the remote keyless entry transmitter. If you are using the remote keyless entry transmitter, the door does not need to be open. 3. Close all doors. Once armed, the alarm will go off if someone tries to enter the vehicle without using the remote keyless entry transmitter or a key or turns the ignition on with an incorrect key. The horn will sound and the turn signal lamps will ﬂash for approximately two minutes. When the alarm is armed, the trunk may be opened with the remote keyless entry transmitter. The power door lock switches are disabled and the doors remain locked. You must use your remote keyless entry transmitter or your key to unlock the doors when the system is armed. 2-17 Arming with the Power Lock Switch The alarm system will arm when you use either power lock switch to lock the doors while any door or the trunk is open and the key is removed from the ignition. Arming with the Remote Keyless Entry Transmitter The alarm system will arm when you use your remote keyless entry transmitter to lock the doors, if the key is not in the ignition. Disarming with the Remote Keyless Entry Transmitter The alarm system will disarm when you use your remote keyless entry transmitter to unlock the doors. The ﬁrst time a remote UNLOCK command is received, three ﬂashes will be seen and three horn chirps heard to indicate an alarm condition has occurred since last arming. Disarming with Your Key The alarm system will disarm when you use your key to unlock the doors or insert your key in ignition and turn it from the OFF position. PASS-Key® III+ The PASS-Key® III+ system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. PASS-Key® III+ uses a radio frequency transponder in the key that matches a decoder in your vehicle. 2-18 PASS-Key® III+ Operation Your vehicle has PASS-Key® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key® III+ is a passive theft-deterrent system. This means you do not have to do anything special to arm or disarm the system. It works when you insert or remove the key from the ignition or transition the key from run, accessory or start from the off position. When the PASS-Key® III+ system senses that someone is using the wrong key, it prevents the vehicle from starting. Anyone using a trial-and-error method to start the vehicle will be discouraged because of the high number of electrical key codes. If the engine does not start and the security light comes on when trying to start the vehicle, the key may have a damaged transponder. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the fuse, see Fuses and Circuit Breakers on page 5-92. If the engine still does not start with the other key, your vehicle needs service. If your vehicle does start, the ﬁrst key may be faulty. See your dealer who can service the PASS-Key® III+ to have a new key made. In an emergency, contact Roadside Assistance. It is possible for the PASS-Key® III+ decoder to “learn” the transponder value of a new or replacement key. Up to nine additional keys may be programmed for the vehicle. The following procedure is for programming additional keys only. If all the currently programmed keys are lost or do not operate, you must see your dealer or a locksmith who can service PASS-Key® III+ to have keys made and programmed to the system. See your dealer or a locksmith who can service PASS-Key® III+ to get a new key blank that is cut exactly as the ignition key that operates the system. 2-19 To program the new key do the following: 1. Verify that the new key has a + stamped on it. 2. Insert the original, already programmed, key in the ignition and start the engine. If the engine will not start, see your dealer for service. 3. After the engine has started, turn the key to OFF, and remove the key. 4. Insert the new key to be programmed and turn it to the RUN position within ﬁve seconds of removing the original key. 5. The security light will turn off once the key has been programmed. 6. Repeat Steps 1 through 5 if additional keys are to be programmed. If you are driving and the security light comes on and stays on, you may be able to restart your engine. Your PASS-Key® III+ system, however, may not be working properly and must be serviced by your dealer. If you lose or damage your PASS-Key® III+ key, see your dealer or a locksmith who can service PASS-Key® III+ to have a new key made. Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:127) Do not drive at any one constant speed, fast or slow, for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. Avoid downshifting to brake, or slow, the vehicle. (cid:127) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time your new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:127) Do not tow a trailer during break-in. See Towing a Trailer on page 4-36 for the trailer towing capabilities of your vehicle and more information. Following break-in, engine speed and load can be gradually increased. 2-20 Ignition Positions With the ignition key in the ignition, the key can be turned to four different positions: Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand. Make sure the key is in all the way. If none of this works, then your vehicle needs service. A (OFF): This is the only position in which the ignition key can be inserted or removed. This position locks the ignition and transaxle. It is a theft-deterrent feature. B (ACCESSORY): This position lets the radio and windshield wipers operate while the engine is off. To use ACCESSORY, turn the key clockwise. C (RUN): This position is where the key returns to after the vehicle is started. This position displays some of the warning and indicator lights. D (START): This position starts the engine. A warning chime will sound and the Driver Information Center (DIC) will display a warning message when the driver’s door is opened if the ignition is in OFF, ACCESSORY and the key is in the ignition. See DIC Warnings and Messages on page 3-45 for more information. 2-21 Retained Accessory Power (RAP) The vehicle has Retained Accessory Power (RAP), which will allow your vehicle’s radio to work when the ignition key is in the RUN or ACCESSORY position. Once the key is turned from RUN to OFF the radio will continue to work 10 minutes or until the driver’s door is opened. Also, the power windows will continue to work for up to 10 minutes or until any door is opened. Starting the Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle. Shift into PARK (P) only when your vehicle is stopped. Starting Your Engine 1. With your foot off the accelerator pedal, turn your ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter. 2. If your vehicle does not start within 10 seconds, hold the key in START for about 10 seconds at a time until the engine starts. Wait about 15 seconds between each try. 3. If the engine still will not start, or starts but then stops, it could be ﬂooded with too much gasoline. Try pushing your accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for about three seconds. If the vehicle starts brieﬂy but then stops again, do the same thing. This time keep the pedal down for ﬁve or six seconds to clear the extra gasoline from the engine. After waiting about 15 seconds, repeat the normal starting procedure. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. Any resulting damage would not be covered by your vehicle’s warranty. 2-22 Engine Coolant Heater Your vehicle may have this feature. In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is attached to the underside of the diagonal brace, which is located above the engine air cleaner/ﬁlter assembly. 3. Plug it into a normal, grounded 110-volt AC outlet. {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you will be parking your vehicle. The dealer can give you the best advice for that particular area. 2-23 Displacement on Demand™ (DoD™) (5.3L V8 Engine) Your vehicle’s engine may be equipped with Displacement on Demand™ (DoD™). This system allows the engine to operate on either all or half of its cylinders, depending on your driving conditions. When less power is required, such as cruising at a constant vehicle speed, the system will operate in the half cylinder mode, allowing your vehicle to achieve better fuel economy. When greater power demands are required, such as accelerating from a stop, passing, or merging onto a freeway, the system will maintain full-cylinder operation. When greater power demands are required, such as accelerating from a stop, passing, or merging onto a freeway, the system will maintain eight-cylinder operation. When less power is required, such a cruising at a constant vehicle speed, the system will automatically enable the four-cylinder mode, allowing your vehicle to achieve better fuel economy. Automatic Transaxle Operation Your automatic transaxle has a shift lever on the steering column or on the console between the seats. There is a display, located on the instrument panel cluster that will indicate the gear the vehicle is in. Maximum engine speed is limited on automatic transaxle vehicles while you are in PARK (P) or NEUTRAL (N) to protect driveline components from improper operation. There are several different positions for the shift lever. PARK (P): This position locks your front wheels. It is the best position to use when the engine is started because your vehicle cannot move easily. 2-24 {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 4-36. Make sure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transaxle shift lock control system. You must fully apply your regular brakes before you can shift from PARK (P) while the ignition is in RUN. If you cannot shift out of PARK (P), ease pressure on the shift lever by pushing it all the way into PARK (P) while keeping the brake pedal pushed down. Release the shift lever button if you have a console shift. Then move the shift lever out of PARK (P). See Shifting Out of Park (P) on page 2-30. REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice, or sand without damaging your transaxle, see If Your Vehicle is Stuck in Sand, Mud, Ice or Snow on page 4-28. 2-25 NEUTRAL (N): In this position, your engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when your vehicle is being towed. {CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. Notice: Shifting out of PARK (P) or NEUTRAL (N) while the engine is running at high speed may damage the transaxle. The repairs would not be covered by your warranty. Be sure the engine is not running at high speeds when shifting your vehicle. 2-26 AUTOMATIC OVERDRIVE (D): This position is for normal driving. If you need more power for passing, and you are: (cid:127) Going less than 35 mph (55 km/h), push the accelerator pedal about halfway down. (cid:127) Going about 35 mph (55 km/h) or more, push the accelerator pedal all the way down. If your vehicle seems to start up rather You will shift down to the next gear and have more power. Notice: slowly or not shift gears when you go faster, and you continue to drive your vehicle that way, you could damage the transaxle. Have your vehicle serviced right away. You can drive in SECOND (2) when you are driving less than 35 mph (55 km/h) and AUTOMATIC OVERDRIVE X for higher speeds until then. THIRD (3): This position is also used for normal driving, but it offers more power and lower fuel economy than AUTOMATIC OVERDRIVE (D). Here are some times you might choose THIRD (3) instead of AUTOMATIC OVERDRIVE (D): (cid:127) When driving on hilly, winding roads (cid:127) When towing a trailer, so there is less shifting between gears (cid:127) When going down a steep hill. For more information, see Hill and Mountain Roads on page 4-22. SECOND (2): This position gives you more power but lower fuel economy than THIRD (3). You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads. You would also then want to use your brakes off and on. Notice: Driving in SECOND (2) for more than 25 miles (40 km) or at speeds over 55 mph (90 km/h) may damage the transaxle. Also, shifting into SECOND (2) at speeds above 65 mph (105 km/h) can cause damage. Drive in THIRD (3) or AUTOMATIC OVERDRIVE (D) instead of SECOND (2). FIRST (1): This position gives you even more power, but lower fuel economy than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the shift lever is in FIRST (1), the transaxle will not shift into ﬁrst gear until the vehicle is going slowly enough. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transaxle. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes, or parking brake to hold the vehicle in place. Parking Brake The parking brake is located to the left of the brake pedal, near the driver’s door. To set the parking brake, hold the brake pedal down with your right foot. Push down the parking brake pedal with your left foot. To release the parking brake, hold the brake pedal down with your right foot and push the parking brake pedal with your left foot. When you lift your left foot, the parking brake pedal will follow it to the released position. 2-27 A warning chime will sound and a brake warning light located on the instrument panel cluster will come on, if the parking brake is set, the ignition is on and the shift lever is not in PARK (P). Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and parking on any hill, see Towing a Trailer on page 4-36. Shifting Into Park (P) {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into Park (P) on page 2-28. If you are pulling a trailer, see Towing a Trailer on page 4-36. 2-28 Steering Column Shift Lever 1. Hold the brake pedal down with your right foot and set the parking brake. 2. Move the shift lever into PARK (P) by pulling the shift lever toward you and moving it up as far as it will go. 3. Turn the ignition key to OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). Console Shift Lever 1. Hold the brake pedal down with your right foot and set the parking brake. 2. Move the shift lever into PARK (P) by holding in the button on the shift lever and pushing the lever all the way toward the front of the vehicle. 3. Turn the ignition key to OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into the PARK (P) position, hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pulling it toward you or if you have the console shift lever, without ﬁrst pushing the button. If you can, it means that the shift lever was not fully locked into PARK (P). 2-29 Torque Lock If you are parking on a hill and you do not shift your transaxle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into Park (P) on page 2-28. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transaxle, so you can pull the shift lever out of PARK (P). Shifting Out of Park (P) Your vehicle has an automatic transaxle shift lock control system. You must fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN. See Automatic Transaxle Operation on page 2-24. If you cannot shift out of PARK (P), ease pressure on the shift lever by pushing it all the way into PARK (P) while keeping the brake pedal pushed down. Release the shift lever button if you have a console shift. Then move the shift lever out of PARK (P), being sure to press the shift lever button if you have a console shift. If you ever hold the brake pedal down but still cannot shift out of PARK (P), try this: 1. Turn the ignition key to ACCESSORY. 2. Apply and hold the brake pedal down until the end of Step 4. 3. Shift to NEUTRAL (N). 4. Start the engine and shift to the drive gear you want. 5. Have the vehicle ﬁxed as soon as you can. 2-30 Parking Over Things That Burn Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system had been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. 2-31 {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-31. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-24. It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) on page 2-28. If you are parking on a hill and if you are pulling a trailer, also see Towing a Trailer on page 4-36. 2-32 Mirrors Manual Rearview Mirror If the vehicle has this mirror, it has a lever located at the bottom of the mirror between the two lamps. The lever is used to change the mirror from the day to the night position. To reduce glare from headlamps behind you while driving at night, pull the lever toward you. To return the mirror to the day position, return the lever to its original position. There are two map lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. Manual Rearview Mirror with OnStar® If the vehicle has this mirror, it has a lever located at the bottom of the mirror between the two lamps. The lever is used to change the mirror from the day to the night position. To reduce glare from headlamps behind you while driving at night, pull the lever toward you. To return the mirror to the day position, return the lever to its original position. There are two map lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. There are also OnStar® buttons located at the bottom of the mirror face. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-35 for more information about the services OnStar® provides. Automatic Dimming Rearview Mirror with OnStar® The vehicle may have an automatic dimming rearview mirror with the OnStar® System. Press the button located below the mirror, on the far left, for up to three seconds to turn the automatic dimming feature off and on. There are two map lamps located on the bottom of the mirror. Press the button next to each lamp to turn it on and off. There are also OnStar® buttons located at the bottom of the mirror. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 2-35 for more information about the service OnStar® provides. 2-33 Heated Outside Mirrors If your vehicle has this feature, the surface of the outside mirrors will heat when the rear window defogger is activated. Outside Convex Mirror Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. Outside Power Mirrors The outside power mirror controls are located on the driver’s door armrest. Use the selector switch located below the four-way control panel to choose either the left or right outside mirror. Then press any of the four arrows located on the control pad to move each mirror in the desired direction. Adjust each mirror so you can see the side of your vehicle and the area beside and behind your vehicle. The mirrors can be manually folded toward the vehicle when going through car washes or conﬁned spaces. 2-34 OnStar® System OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar® Emergency where we can request emergency services be sent to your location. If you lock your keys in the car, call OnStar® at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar® button and they will get you the help you need. A complete OnStar® User’s Guide and the Terms and Conditions of the OnStar® Subscription Service Agreement are included in the vehicle’s glove box literature. For more information, visit www.onstar.com or www.onstar.ca. Contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827), or press the OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com or www.onstar.ca. OnStar® Services For new vehicles equipped with OnStar®, the Safe and Sound Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions and Connections® Plan to meet your needs. For more information, press the OnStar® button to speak to an advisor. Safe and Sound Plan (cid:127) Advanced Automatic Collision Notiﬁcation (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Tracking (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) Remote Diagnostics (cid:127) Online Concierge 2-35 Directions and Connections® Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions (cid:127) RideAssist Information and Convenience Services OnStar® Personal Calling As an OnStar® subscriber, the Personal Calling capability allows you to make hands-free calls using a wireless system that is integrated into the vehicle. Calls can be placed nationwide using simple voice commands with no additional contracts and no additional roaming charges. To ﬁnd out more about OnStar® Personal Calling, refer to the OnStar® User’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak to an OnStar® advisor by pressing the OnStar® button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor Your vehicle may have Virtual Advisor. It is a feature of OnStar® Personal Calling that uses minutes to access weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. Customize your information proﬁle at www.myonstar.com. See the OnStar® User’s Guide for more information. OnStar® Steering Wheel Controls Your vehicle may be equipped with a Talk/Mute button that can be used to interact with OnStar®. See Audio Steering Wheel Controls on page 3-80 for more information. When calling into voice-mail systems, or to dial directory numbers, press this button once, wait for the response, say the number(s) to be dialed, wait for the number(s) to be repeated and then say “dial”. See the OnStar® User’s Guide for more information. 2-36 (cid:127) Universal Home Remote System The Universal Home Remote System, provides a way to replace up to three hand-held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems, and home lighting. If your vehicle has the Universal Home Remote Transmitter, it complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Changes and modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Universal Home Remote System Operation Do not use the Universal Home Remote with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the programming of your Universal Home Remote Transmitter. 2-37 Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming steps. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section or, for assistance, see Customer Assistance Offices on page 7-4. Be sure that people and objects are clear of the garage door or gate operator you are programming. When programming a garage door, it is advised to park outside of the garage. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Programming Universal Home Remote Follow these steps to program up to three channels: 1. Press and hold down the two outside Universal Home Remote buttons, releasing only when the Universal Home Remote indicator light begins to ﬂash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third hand-held transmitter to the remaining two Universal Home Remote buttons. 2. Position the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the desired Universal Home Remote button and the hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 4. The indicator light will ﬂash slowly at ﬁrst and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 2-38 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on constantly, programming is complete and your device should activate when the Universal Home Remote button is pressed and released. To program the remaining two Universal Home Remote buttons, begin with Step 2 under “Programming Universal Home Remote.” Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code equipped device, most commonly, a garage door opener. 6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. 8. Return to the vehicle. Firmly press and hold the programmed Universal Home Remote button for two seconds, then release. Repeat the press/hold/release sequence a second time, and depending on the brand of the garage door opener, or other rolling code device, repeat this sequence a third time to complete the programming. The Universal Home Remote should now activate your rolling-code equipped device. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming Universal Home Remote.” You do not want to repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. 2-39 Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons To erase programming from the three Universal Home Remote buttons do the following: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. Do not hold the two outside buttons for longer than 30 seconds. 2. Release both buttons. The Universal Home Remote is now in the train (learning) mode and can be programmed at any time beginning with Step 2 under “Programming Universal Home Remote” shown earlier in this section. Individual buttons cannot be erased, but they can be reprogrammed. See “Reprogramming a Single Universal Home Remote Button” following this section. 2-40 Reprogramming a Single Universal Home Remote Button To program a device to Universal Home Remote using a Universal Home Remote button previously trained, follow these steps: 1. Press and hold the desired Universal Home Remote button. Do not release the button. 2. The indicator light will begin to ﬂash after 20 seconds. While still holding the Universal Home Remote button, proceed with Step 2 under “Programming Universal Home Remote” shown earlier in this section. For additional information on Universal Home Remote, see Customer Assistance Offices on page 7-4. Storage Areas Glove Box To open the glove box, lift up on the lever. Cupholder(s) If equipped, there are cupholders built into the front center console, front portion of the front center seat and rear armrest. To access the front cupholders, on the ﬁve-passenger model, pull out the swing arm in front of the front center console to divide the opening into two cupholders. To access the front cupholders, on the six-passenger model, fold the front portion of the front center seat forward. Sunglasses Storage Compartment Your vehicle may be equipped with a sunglasses storage compartment located above the rearview mirror. To open, push on cover. Do not operate vehicle with the sunglasses storage compartment cover open, it could obstruct your view. 2-41 Center Console Storage Area If equipped, your vehicle has a front center console area. To open the front center console storage area, pull up on the latch located in the front of the console lid. Inside is a removable tray and an accessory power outlet. Rear Storage Area If your vehicle has the split folding rear seat, there will be two storage areas underneath. To access these storage areas, pull the tab(s) located by the seatbelt buckle on the passenger side and the center of the rear seat on the driver side. See Split Folding Rear Seat on page 1-8 for more information. Rear Seat Armrest Your vehicle may be equipped with a rear seat armrest. To access, pull the tab on the armrest forward. Convenience Net The vehicle may have a convenience net located on the back wall of the trunk. The net is not for larger, heavier loads. Store those in the trunk as far forward as possible. Unhook the net so that it will lie ﬂat when not in use. Sunroof If your vehicle is equipped with a sunroof, the sunroof switches are located on the overhead console. 2-42 The sunroof can only be operated when the ignition is in ACCESSORY, RUN, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-22. Q (Vent/Express-Open): To vent the sunroof when it is closed, press this switch once. When using the vent, the sunshade should be fully opened. The sunshade can be opened or closed manually by sliding it rearward or forward. From the vent position, press this switch again to activate the express-open feature. Press the close switch to stop movement of the sunroof. The sunshade will automatically open when using express-open. A deﬂector will automatically pop up when the sunroof is opened. The deﬂector will retract when the sunroof is closed. R (Close): To close the sunroof, press and hold this switch until the sunroof motor stops, or release the switch when the desired position has been reached. 2-43 ✍ NOTES 2-44 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-7 Headlamp High/Low-Beam Changer ..................3-8 Flash-to-Pass .................................................3-8 Windshield Wipers ..........................................3-8 Windshield Washer .........................................3-9 Cruise Control ..............................................3-10 Exterior Lamps .............................................3-13 Delayed Headlamps ......................................3-14 Daytime Running Lamps (DRL)/Automatic Headlamp System .....................................3-14 Fog Lamps ..................................................3-15 Instrument Panel Brightness ...........................3-15 Courtesy Lamps ...........................................3-15 Dome Lamp .................................................3-15 Entry Lighting ...............................................3-16 Delayed Entry Lighting ...................................3-16 Delayed Exit Lighting .....................................3-16 Parade Dimming ...........................................3-17 Reading Lamps ............................................3-17 Battery Run-Down Protection ..........................3-17 Accessory Power Outlet(s) .............................3-17 Ashtray(s) and Cigarette Lighter ......................3-18 Climate Controls ............................................3-19 Climate Control System .................................3-19 Outlet Adjustment .........................................3-22 Passenger Compartment Air Filter ...................3-23 Warning Lights, Gages, and Indicators ............3-24 Instrument Panel Cluster ................................3-25 Speedometer and Odometer ...........................3-26 Tachometer .................................................3-26 Safety Belt Reminder Light .............................3-26 Passenger Safety Belt Reminder Light .............3-26 Airbag Readiness Light ..................................3-27 Passenger Airbag Status Indicator ...................3-28 Charging System Light ..................................3-30 3-1 Section 3 Instrument Panel Brake System Warning Light ..........................3-30 Anti-Lock Brake System Warning Light .............3-31 Traction Control System (TCS) Warning Light ......3-32 Engine Coolant Temperature Warning Light ......3-32 Engine Coolant Temperature Gage ..................3-33 Tire Pressure Light .......................................3-33 Malfunction Indicator Lamp .............................3-34 Oil Pressure Light .........................................3-36 Security Light ...............................................3-37 Fog Lamp Light ............................................3-37 Cruise Control Light ......................................3-38 Highbeam On Light .......................................3-38 Fuel Gage ...................................................3-38 Driver Information Center (DIC) .......................3-39 DIC Operation and Displays ...........................3-39 DIC Warnings and Messages .........................3-45 DIC Vehicle Customization .............................3-53 Audio System(s) .............................................3-58 Setting the Time (Without Date Display) ...........3-60 Setting the Time (With Date Display) ...............3-60 Radio with CD (Base) ...................................3-61 Radio with CD (MP3) ....................................3-65 Theft-Deterrent Feature ..................................3-80 Audio Steering Wheel Controls .......................3-80 Radio Reception ...........................................3-81 Care of Your CDs .........................................3-82 Care of the CD Player ...................................3-82 Backglass Antenna .......................................3-82 XM™ Satellite Radio Antenna System .............3-83 3-2 ✍ NOTES 3-3 Instrument Panel Overview 3-4 The main components of your instrument panel are listed here: A. Air Vent. See Outlet Adjustment on page 3-22. B. Remote Trunk Release Button. See “Remote Trunk Release” under Trunk on page 2-13. C. Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. D. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-25. E. Hazard Warning Flasher Button. See Hazard Warning Flashers on page 3-6. F. Driver Information Center. See Driver Information Center (DIC) on page 3-39. G. Passenger Air Bag status Indicator. See Passenger Airbag Status Indicator on page 3-28. H. Audio System. See Audio System(s) on page 3-58. I. Exterior Lamps Control. See Exterior Lamps on page 3-13. J. Instrument Lanel Brightness. See Instrument Panel Brightness on page 3-15. K. Traction Control On/Off Button (If Equipped). See Traction Control System (TCS) on page 4-9. L. Tilt Steering Wheel Lever. See Tilt Wheel on page 3-6. M. Steering Wheel Cruise Control (If Equipped). See Cruise Control on page 3-10. N. Hood Release. See Hood Release on page 5-11. O. Horn. See Horn on page 3-6. P. Audio Steering Wheel Controls (Option). See Audio Steering Wheel Controls on page 3-80. Q. Ignition Switch. See Ignition Positions on page 2-21. R. Climate Controls. See Climate Control System on page 3-19. S. Accessory Power Outlets. See Accessory Power Outlet(s) on page 3-17. T. Center Console Shift Lever (If Equipped). See “Console Shift Lever” under Shifting Into Park (P) on page 2-28. U. Glove Box. See Glove Box on page 2-41. 3-5 Horn Press near or on the horn symbols on your steering wheel pad to sound the horn. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise the steering wheel to the highest level to give your legs more room when you enter and exit the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column. To tilt the wheel, hold the wheel and pull the lever. Then move the wheel to a comfortable position and release the lever to lock the wheel in place. Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located on top of the steering column. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key is not in. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals will not work. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. 3-6 Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane Change Signals. See Turn and Lane-Change Signals on page 3-7. (cid:127) 2 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-8. Flash-to-Pass. See Flash-to-Pass on page 3-8. (cid:127) N Windshield Wipers. See Windshield Wipers on page 3-8. (cid:127) LQ Windshield Washer. See Windshield Washer on page 3-9. For information on the headlamps, see Exterior Lamps on page 3-13. Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. To signal a lane change, just raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever will return by itself when you release it. If you momentarily press and release the lever, the turn signal will ﬂash three times. If the arrow ﬂashes faster than normal as you signal a turn or a lane change, a signal bulb may be burned out and other drivers won’t see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows don’t go on at all when you signal a turn, check for burned-out bulbs and then check the fuse. See Fuses and Circuit Breakers on page 5-92. 3-7 (cid:127) Turn Signal On Chime If you leave either one of your turn signals on and drive more than 3/4 mile (1.2 km), a chime will sound to alert you. Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever away from you. When the high beams are on, a light on the instrument panel cluster also will be on if the ignition is in the on position. To change the headlamps from high beam to low beam, pull the turn signal lever toward you. Flash-to-Pass With the turn signal lever in the low-beam position, pull the lever toward you momentarily to switch to high-beams (to signal that you are going to pass). If you have the headlamps on, they will return to low-beams when you release the lever. This feature operates even when the headlamps are off. Windshield Wipers Be sure to clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, gently loosen or thaw them. Damaged wiper blades may not clear the windshield well, making it harder to see and drive safely. If the blades do become damaged, install new blades or blade inserts. For more information, see Windshield Wiper Blade Replacement on page 5-52 Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Clear away snow or ice to prevent an overload. You control the windshield wipers by turning the band with the wiper symbol on it. 8(Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer. 3-8 N(Delay): You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow. Turn the band to choose the delay time. The closer to the top of the lever, the shorter the delay. 6 (Low Speed): For steady wiping at low speed, turn the band away from you to the ﬁrst solid band past the delay settings. For high-speed wiping, turn the band further, to the second solid band past the delay settings. To stop the wipers, move the band to off. 1 (High Speed): For high-speed wiping, turn the band further, to the second solid band past the delay settings. 9(Off): To stop the wipers, move the band to off. Windshield Washer At the top of the multifunction lever, there’s a paddle with the windshield washer symbol on it. To spray washer ﬂuid on the windshield, push the paddle. The wipers will run for several sweeps and then either stop or return to your preset speed. The ignition key must be in ACCESSORY or RUN for this to work. See Windshield Washer Fluid on page 5-39. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. United States Canada When you are low on washer ﬂuid, the LOW WASHER FLUID message will be illuminated in the message center for 60 seconds. When the ignition is turned off, this message will appear again for three seconds to remind you that the ﬂuid level is low. Until the ﬂuid tank is reﬁlled, every time you start your vehicle, the LOW WASHER FLUID message will be illuminated in the message center for 60 seconds. Be sure to reﬁll the tank right away. 3-9 Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When you apply your brakes, cruise control is turned off. {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Do not use cruise control on slippery roads. If your vehicle is in cruise control when the traction control system (option) begins to limit wheel spin, the cruise control will automatically disengage. 3-10 See Traction Control System (TCS) on page 4-9. When road conditions allow you to safely use it again, you may turn the cruise control back on. The cruise control buttons are located on left side of the steering wheel. T(On/Off): This button can both activate and turn off the system. The indicator is lit when cruise control is on and turns off when cruise control is off. + RES (Resume/Accelerate): Press this button to make the vehicle accelerate or resume to a previously set speed. Set– (Set): Press this button to set the speed or make the vehicle decelerate. [ (Cancel): Press this button to cancel cruise control. Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This shuts off the cruise control. But you don’t need to reset it. Once you are driving about 25 mph (40 km/h) or more, press the +RES button on your steering wheel. The vehicle will go back to your chosen speed and stay there. Increasing Speed While Using Cruise Control To increase the cruise speed while using cruise control: (cid:127) Press and hold the +RES button on the steering wheel until you reach your new desired speed, then release it. To increase vehicle speed in small increments, press the +RES button. Setting Cruise Control Cruise control will not work if your parking brake is set, or if the master cylinder brake ﬂuid level is low. If you apply your brakes, the cruise control will shut off. The CRUISE light on the instrument panel cluster will come on after the cruise control has been set to the desired speed. {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Press the cruise control ON/OFF button. 2. Get up to the speed you want. 3. Press the SET- button located on the steering wheel and release it. 4. Take your foot off the accelerator. 3-11 (cid:127) Reducing Speed While Using Cruise Control To reduce your speed while using cruise control: (cid:127) Press and hold the SET– button on the steering wheel until you reach the lower speed you want, then release it. To slow down in very small amounts, press the cancel button on the steering wheel brieﬂy. Each time you do this, you’ll go about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise speed you set earlier. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control There are three ways to end cruise control: (cid:127) Step lightly on the brake pedal. (cid:127) Press the cancel button on the steering wheel. (cid:127) Press the ON/OFF button on the steering wheel. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased. 3-12 (cid:127) Exterior Lamps The exterior lamps control is located on the instrument panel to the left of the steering wheel. Instrument Panel Lights Taillamps ;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: It controls the following systems: (cid:127) Headlamps Taillamps (cid:127) Parking Lamps License Plate Lamps Instrument Panel Lights Fog Lamps The exterior lamps control has four positions: 9(Off): Momentarily turn the control to this position to turn off the automatic light control. Momentarily turn to this position again to turn automatic light control on again. AUTO (Automatic): Turn the control to this position to automatically turn on the headlamps at normal brightness, together with the following: (cid:127) Parking Lamps License Plate Lamps Taillamps License Plate Lamps Instrument Panel Lights 2(Headlamps): Turn the control to this position to turn on the headlamps together with the following lamps listed below. A warning chime will sound if you open the driver’s door when the ignition switch is off and the headlamps are on. (cid:127) Parking Lamps License Plate Lamps Instrument Panel Lights Taillamps - (Fog Lamps): Push the fog lamps control in to turn on the fog lamps. See Fog Lamps on page 3-15. 3-13 (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Delayed Headlamps The delayed headlamps feature provides a period of exterior lighting as you leave the area around your vehicle. The feature is activated when the headlamps are on due to the automatic headlamps control feature described previously in this section, and when the ignition is turned off. Your headlamps will then remain on until the exterior lamps control is moved to the parking lamps position or until the pre-selected delayed headlamp lighting period has ended. If you turn off the ignition with the headlamps switch in the parking lamps or headlamps position, the delayed headlamps cycle will not occur. To disable the delayed headlamps feature or change the time of delay, see DIC Vehicle Customization on page 3-53. Daytime Running Lamps (DRL)/Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. 3-14 A light sensor on top of the instrument panel makes the DRL work, so be sure it isn’t covered. The DRL system’s automatic headlamp control will make your low-beam headlamps come on at a reduced brightness when the following conditions are met: The ignition is in RUN. The exterior lamps control is in AUTO. The engine is running. When the DRL are on, only your low-beam headlamps, at a reduced level of brightness, will be on. The headlamps, taillamps, sidemarker and other lamps won’t be on. Your instrument panel and cluster won’t be lit up either. When it is dark enough outside, your low-beam headlamps will turn off and the headlamps and parking lamps will turn on. The other lamps that come on with your headlamps will also come on. When it’s bright enough outside, your headlamps will go off and your DRL will come on. As with any vehicle, you should turn on the regular headlamp system when you need it. (cid:127) (cid:127) (cid:127) Fog Lamps - (Fog Lamps): If your vehicle is equipped with fog lamps, it is located on the exterior lamps control. The exterior lamps control is located on the instrument panel to the left of the steering column. Your ignition must be in RUN for the fog lamps to illuminate. To turn the fog lamps on, press exterior lamps button. A light will come on in the button to let you know that the fog lamps are on. Press the exterior lamps button again to turn the fog lamps off. The ignition must be in RUN and the parking lamps must be on for your fog lamps to work. Parking lamps will turn on automatically when you turn on the fog lamps. The fog lamps will go off while you change to high-beam headlamps. The fog lamps will need to be turned on each time the ignition is turned off and back on again. Some localities have laws that require the headlamps to be on along with the fog lamps. Instrument Panel Brightness D (Instrument Panel Brightness): This feature controls the brightness of the instrument panel lights. The knob for this control is located next to the exterior lamps control and between the traction control button and the trunk release button. Push and pull the knob out halfway and turn the knob clockwise for brightness of the instrument panel lights and counter clockwise to turn the brightness down. Turning the knob completely clockwise to the detente will turn on the courtesy lamps. Courtesy Lamps When any door is opened, several lamps come on. These lamps are courtesy lamps. They make it easy for you to enter and leave your vehicle. You can also turn these lamps on by turning the instrument panel brightness control all the way clockwise. Dome Lamp If your vehicle has this feature, the dome lamp will come on when you open a door. You can also turn this lamp on by turning the instrument panel brightness control clockwise as far as it will go. 3-15 Entry Lighting Your vehicle may be equipped with courtesy lamps that will come on and stay on for a set time whenever you press UNLOCK on the remote keyless entry transmitter (if equipped). If you open a door, the lamps will stay on while it’s open and then turn off automatically about 25 seconds after you close it. If you press UNLOCK and don’t open a door, the lamps will turn off after about 40 seconds. Entry lighting includes a feature called theater dimming. With theater dimming, the lamps don’t just turn off at the end of the delay time. Instead, they slowly dim after the delay time until they go out. The delay time is canceled if you turn the ignition key to ON or press the power door lock switch. The lamps will dim right away. When the ignition is on, illuminated entry is inactive, which means the courtesy lamps won’t come on unless a door is opened. Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after all the doors have been closed, the delayed entry lighting feature will continue to work until one of the following occurs: The ignition is in RUN. The doors are locked. (cid:127) An illumination period of 25 seconds has elapsed. If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open. Delayed Exit Lighting This feature illuminates the interior for a period of time after the key is removed from the ignition. The ignition must be off for delayed exit lighting to work. When the key is removed, interior illumination will activate and remain on until one of the following occurs: The ignition is RUN. The power door locks are activated. (cid:127) An illumination period of 20 seconds has elapsed. If during the illumination period a door is opened, the timed illumination period will be canceled and the interior lamps will remain on because a door is open. 3-16 (cid:127) (cid:127) (cid:127) (cid:127) Parade Dimming The instrument panel has an added feature called parade mode. This feature prohibits the dimming of your instrument panel displays during the daylight while the headlamps are on so that you’ll still be able to see the displays. Reading Lamps Your vehicle may be equipped with reading lamps that are located in the dome lamp. Press the button to turn them on and off. Battery Run-Down Protection Your vehicle has a feature to help prevent you from draining the battery in case you accidentally leave on the interior courtesy lamps, reading/map lamps, visor vanity lamps or trunk lamp. If you leave any of these lamps on, they will automatically turn off after 10 minutes, if the ignition is off. The lamps won’t come back on again until you do the following: Turn the ignition on, or turn the exterior lamps control off, then on again. If your vehicle has less than 15 miles (25 km) on the odometer, the battery saver will turn off the lamps after only three minutes. Battery rundown protection will also work if the headlamps are left on. After having been left on for 10 minutes, the headlamps and the parking lamps will ﬂash three times. They will remain on for one more minute before turning off automatically. Accessory Power Outlet(s) Your vehicle has three 12-volt outlets which can be used to plug in electrical equipment such as a cellular telephone, a compact disc player, etc. On vehicles with a center console, one outlet is located at the rear of the console in the bottom of the bin and two outlets are located at the front of the console bin under the instrument panel. Lift the cover to access the outlet. Close the cover when not using the outlet. On vehicles without a center console, two are located under the climate controls and another outlet for the rear seat passengers is at the rear of the center front seat. Remove the rubber cover to access the outlets. When not using the outlet, make sure the cover is on it. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating. 3-17 (cid:127) (cid:127) Certain accessory plugs may not be compatible to the accessory power outlet and could result in blown vehicle

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2006 Chevrolet Impala Owners Manual