Download PDF Manual

Recorded Disc If the disc or track has already been recorded to MEM, the message The Song(s) is Already Recorded displays.


Stopping the Recording Press the O REC button while recording from an MP3/WMA CD or USB storage device to display the stop recording option. Select Stop Recording Song to MEM. Deleting Tracks From MEM Individual tracks and all tracks can be deleted from MEM. To delete individual tracks, press and release the DEL button while the track is playing. To delete all tracks from MEM, press and hold the DEL button while a track is playing.


Playing From MEM


Playing Back a Previously Recorded CD Turn the MENU/SEL knob to select a track if MEM is already playing from the previously recorded disc. 1. Select Recorded Disc List. 2. Select the disc. 3. Select the track.


Searching For a Track Tracks can be searched for by: . Playlists . Artists . Albums . Song Titles . Genres The number of objects in each category is shown in parentheses after the category.


To search for tracks: 1. Press the MENU/SEL knob. 2. Select Search. 3. Select: Playlists, Artists, Albums,


Song Titles, or Genres.


4. Select the track. The search rate


increases if the menu knob is continuously turned while searching in a list.


Shuffle Songs Select the Shuffle Songs option from the MEM menu to randomly play back tracks stored in MEM. Configuring MEM Favorites During MEM playback, press the FAV button to change between favorite categories. The favorite categories are: . Playlists . Artists . Albums . Genres


Infotainment System 6-27


To remove MEM favorites categories: 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select MEM Favorites. 4. Remove the check mark from the box to remove that MEM favorites category.


Replace the check mark to re-add the removed category. Saving MEM Tracks as Favorites Favorites can be saved by pressing and holding one of the 1 to 6 buttons. Favorites can be stored according to the following list: Playlist: Adds currently playing track to the playlist selected. Artist: Saves the artist associated with the currently playing track in the indicated favorites position.


6-28


Infotainment System


Album: Saves the album associated with the currently playing track in the indicated favorites position. Genre: Saves the genre associated with the currently playing track in the indicated favorites position.


Creating Playlists To create a playlist using tracks stored in MEM: 1. Select Playlist from the MEM


favorites.


2. Select the track to be stored in


the playlist.


3. Press and hold one of the


1 to 6 buttons until the track can be heard again to store the track.


4. Repeat steps 1 though 3 to store


additional tracks in the playlist.


Auxiliary Devices (Radio with CD) The auxiliary input allows portable devices to be connected using the 3.5 mm (1/8 in) input jack or the optional USB port. Portable devices are controlled by using the menu system described in Operation on page 6‑7.


The auxiliary input is located in the center console.


3.5 mm Auxiliary Input Jack Playback of an audio device that is connected to the 3.5 mm auxiliary input jack can only be controlled using the controls on the device.


Adjusting the Volume Turn the VOL/ O knob to adjust the volume of the infotainment system after the volume level has been set on the portable audio device. USB Port For vehicles with a USB port, the following devices may be connected and controlled by the infotainment system.


iPod's


. PlaysForSure Devices (PFD) . USB Drives


Zune's


Not all iPod's, PFD's, USB Drives, and Zune's are compatible with the infotainment system.


Connecting and Controlling an iPod™ Not all iPod's can be controlled by the Infotainment System.


Connecting an iPod Connect the iPod to the USB port.


Searching For a Track Tracks can be searched for by: . Playlists . Artists . Albums . Song Titles . Podcasts . Genres . Audiobooks . Composers


To search for tracks: 1. Press the MENU/SEL knob. 2. Select Search. 3. Select: Playlists, Artists, Albums,


Song Titles, Podcasts, Genres, Audiobooks, or Composers.


4. Select the track.


Shuffle Press the MENU/SEL knob and set Shuffle Songs (Random) to On or Off, then press the 0 BACK button to return the main screen. On: Plays tracks in the current folder in random order. Off: Plays tracks in the current folder in sequential order.


Repeat Press the MENU/SEL knob and set Repeat to On or Off, then press the 0 BACK button to return the main screen.


Infotainment System 6-29


On: Repeats the current track. Off: Playback starts from the beginning of the current track after the last track finishes. Connecting and Controlling a PlaysForSure Device (PFD) or Zune™


Connecting a PFD or Zune Connect the PFD or Zune to the USB port.


Searching For a Track Tracks can be searched for by: . Playlists . Artists . Albums . Song Titles . Podcasts . Genres


6-30


Infotainment System


To search for tracks: 1. Press the MENU/SEL knob. 2. Select Search. 3. Select: Playlists, Artists, Albums,


Song Titles, Podcasts, or Genres.


4. Select the track.


Shuffle Functionality Press the MENU/SEL knob and set Shuffle Songs (Random) to On or Off. On: Plays current tracks in random order. Off: Plays current tracks in sequential order.


Repeat Functionality Press the MENU/SEL knob and set Repeat to On or Off. Repeat On: Repeats the current track. Repeat Off: Playback starts from the beginning of the current track after the last track finishes.


Connecting and Controlling a USB Drive The infotainment system can only play back .mp3 and .wma files from a USB drive. Only the first 2,500 songs are recognized on the device. When a device is not supported, the message “No supported data found. You can safely disconnect the device” appears.


Connecting a USB Drive Connect the USB drive to the USB port.


Searching For a Track It is normal for the search feature to take some time to display the information after reading the disc due to the amount of information stored on the disc. Files that do not have any meta data stored in the ID3 tag display as Unknown.


Tracks can be searched for by: . Playlists* . Artists . Albums . Song Titles . Genres


Folder View


*This only displays if a playlist is found on the device. To search for tracks: 1. Press the MENU/SEL knob. 2. Select Search. 3. Select: Playlists, Artists, Albums,


Song Titles, Genres, or Folder View. 4. Select the track.


Auxiliary Devices (Radio with CD/DVD/MEM) The auxiliary input allows portable devices to be connected using the 3.5 mm (1/8 in) input jack or the optional USB port. Portable devices are controlled by using the menu system described in Operation on page 6‑7.


Shuffle Functionality Press the MENU/SEL knob and set Shuffle Songs (Random) to On or Off. On: Plays current tracks in random order. Off: Plays current tracks in sequential order.


Repeat Functionality Press the MENU/SEL knob and set Repeat to On or Off. Repeat On: Repeats the current track. Repeat Off: Playback starts from the beginning of the current track after the last track finishes.


The auxiliary input is located in the center console.


Infotainment System 6-31


3.5 mm Auxiliary Input Jack Playback of an audio device that is connected to the 3.5 mm auxiliary input jack can only be controlled using the controls on the device.


Adjusting the Volume Turn the VOL/ O knob to adjust the volume of the infotainment system after the volume level has been set on the portable audio device. USB Port The following devices may be connected to the USB port and controlled by the infotainment system.


iPod's


. USB Mass Storage Devices Not all iPod's or USB Mass Storage Devices are compatible with the infotainment system.


6-32


Infotainment System


Connecting and Controlling an iPod™ Not all iPod's can be controlled by the Infotainment System.


Connecting an iPod Connect the iPod to the USB port.


Selecting a Track Using the control buttons: . Press g SEEK or l SEEK to select the previous or next track. Turn the MENU/SEL knob to select the track in the current sub menu. The track will start to play.


Playing Tracks in Random Order Press the MENU/SEL knob and set Shuffle Songs to On or Off. Shuffle On: Plays current tracks in random order. Shuffle Off: Plays current tracks in sequential order.


Searching For a Track Tracks can be searched for by: . Playlists . Artists . Albums . Song Titles . Genres . Composers . Audiobooks The number of objects in each category is shown in parentheses after the category. To search for tracks: 1. Press the MENU/SEL knob. 2. Select Search. 3. Select: Playlists, Artists,


Albums, Song Titles, Genres, Composers, or Audiobooks.


4. Select the track. The search rate increases if the MENU/SEL knob is continuously turned while searching in a list.


Connecting and Controlling a USB Drive Files that are not stored in folders are displayed in the root directory (USB).


Connecting a USB Drive Connect the USB drive to the USB port.


Disconnecting a USB Drive A USB drive should be ejected from the USB port before disconnecting it. To eject a USB drive: 1. Press the MENU/SEL knob. 2. Select USB Eject.


Playing Tracks in Random Order Press the MENU/SEL knob and then set Shuffle Songs to On.


Selecting a Track Using the control buttons: . Press g SEEK or l SEEK to select the previous or next track. Turn the MENU/SEL knob to select a track in the current sub menu. The track will start to play.


Selecting a track in a different folder: 1. Press the MENU/SEL knob. 2. Select Folder List. 3. Select the folder. 4. Select the track.


Searching for Tracks It is normal for the search feature to take some time to display the information after reading the device due to the amount of information stored. Files that do not have any meta data stored in the ID3 tag display as Unknown.


Tracks can be searched by: . Playlists . Artists . Albums . Song Titles . Genres The number of objects in each category is shown in parentheses after the category. To search for tracks: 1. Press the MENU/SEL knob. 2. Select Search. 3. Select: Playlists, Artists,


Albums, Song Titles, Genres, Composers, or Audiobooks.


4. Select the track. The search rate increases if the MENU/SEL knob is continuously turned while searching in a list.


Recording Tracks to MEM See Mass Storage Media (MEM) on page 6‑25 for more information.


Infotainment System 6-33


Rear Seat Infotainment


Rear Seat Entertainment (RSE) System The vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system works with the vehicle's infotainment system. The DVD player is part of the front radio. The RSE system includes a radio with a DVD player, two rear seat video display screens, audio/video jacks, two wireless headphones, and a remote control. See CD/DVD Player on page 6‑21 or the separate navigation system manual for more information on the vehicle's DVD system.


6-34


Infotainment System


Before Driving The RSE is for rear seat passengers only. The driver cannot safely view the video screen while driving. In severe or extreme weather conditions, the RSE system may not work until the temperature is within the operating range. The operating range is above −20°C (−4°F) and below 60°C (140°F). If the temperature is outside of this range, heat or cool the vehicle until it is within the operating range. Global Off Depending on the infotainment system, the RSE system may have a Global Off feature. The Global Off feature disables all RSE system features. Press and hold the radio power button for more than three seconds for Global Off to disable the RSE features.


On some infotainment systems, the Global Off feature can be turned off by performing one of the following: . Press and hold the radio power


button for more than three seconds. Insert or eject any disc. Insert a DVD video disc.


. Press the Remote Control power


button.


. Press the MEM/DVD/AUX button


or the k button when a DVD video disc is in the player.


. Press the SRC button on the steering wheel when a DVD video disc is in the player.


. Cycle the ignition.


Headphones RSE includes two 2-channel wireless headphones. Channel 1
is dedicated to the DVD player, and Channel 2 is dedicated to any external auxiliary device connected to the A/V jacks. The headphones are used to listen to various multi‐media. The wireless headphones have an On/Off button, channel 1/2 switch, and a volume control. Turn the headphones off when not in use. Push the On/Off button to turn on the headphones. A light on the headphones comes on. If the light does not come on, check the batteries. Intermittent sound or static can also indicate weak batteries. See “Battery Replacement” later in this section for more information.


Infrared transmitters are on the top of the left seatback video screen. The headphones shut off automatically to save the battery power if the RSE system is shut off or if the headphones are out of range of the transmitters for more than three minutes. Moving too far forward or stepping out of the vehicle, can cause the headphones to lose the signal or have static. The headphones may automatically turn off after four hours of continuous use. To adjust the volume on the headphones, use the volume control. For best audio performance, the headphones must be worn correctly, with the headband over the top of the head. L (Left) and R (Right) are above the ear pads and are indicators as to how the headphones should be placed on the head.


Notice: Do not store the headphones in heat or direct sunlight. This could damage the headphones and repairs will not be covered by the warranty. Storage in extreme cold can weaken the batteries. Keep the headphones stored in a cool, dry place. If the foam ear pads become worn or damaged, they can be replaced separately from the headphones. See your dealer/retailer for more information.


Battery Replacement To change the batteries: 1. Loosen the screw to the battery door located on the left side of the headphones.


2. Slide the battery door open. 3. Replace the two AAA batteries. 4. Replace the battery door and


tighten the screw.


Infotainment System 6-35


Remove the batteries if the headphones are not going to be used for a long period of time. Audio/Video (A/V) Jacks If available, the A/V jacks are located on the rear of the floor console. They allow audio or video cables to be connected from an auxiliary device such as a camcorder or a video game system. The A/V jacks are color coded: . Yellow for video input. . White for left audio input. . Red for right audio input. Power for auxiliary devices is not supplied by the radio system. To use the auxiliary inputs of the RSE system: 1. Connect the auxiliary device


cables to the A/V jacks.


2. Power on both the auxiliary device and the RSE video screen.


6-36


Infotainment System


Changing the Source on the Video Display Screens The image from the auxiliary device can be switched between the video display screens. To change the display: 1. Press the AUX button on the remote control to change the source of both video screens from the DVD player to the auxiliary device.


2. Press the AUX button a second


time to change the left video screen source to the DVD player and the right video screen to the auxiliary device.


3. Press the AUX button a third time to change the left video screen source to the auxiliary device and the right video screen to the DVD player.


4. Press the AUX button a fourth


time to change the source of both video screens to the DVD player.


How to Change the RSE Video Screen Settings The screen display mode, brightness, and language can be changed from the setup menu using the remote control. To change a setting: 1. Press z . 2. Use n , q , p , o and r to


select the settings.


3. Press z again to exit the


setup menu.


Audio Output Audio from the DVD player or auxiliary inputs can be heard through the following: . Wireless Headphones . Vehicle Speakers The RSE system transmits the audio signal to the wireless headphones if an audio signal is available. See “Headphones” earlier in this section for more information. The front seat passengers are able to listen to playback from the A/V jacks through the vehicle speakers by selecting Rear A/V as the source on the radio.


Video Screens The video screens are located in the back of the driver and front passenger seats.


To use the video screen: 1. Push the release button located


on the seatback console.


2. Move the screen to the desired


viewing position.


Push the video screen down into its locked position when it is not in use, the screen turns off automatically. Only the left RSE seatback console contains the infrared transmitters for the wireless headphones, they may be visible as eight illuminated LEDs. These LEDs are not on the right video screen. Both seatback consoles contain an infrared receiver for the remote control. They are located at the top of each console. Notice: Avoid directly touching the video screen, as damage may occur. See “Cleaning the Video Screen” later in this section for more information.


Infotainment System 6-37


Video Screen Input Jack Each video screen is equipped with a video input jack to allow video cables to be connected from an auxiliary device such as a camcorder or a video game system. This signal will override any video provided by the RSE system; either the DVD or Auxiliary A/V jack source. The RSE system must be on for this input to operate. Remote Control To use the remote control, aim it at the transmitter window at either seatback console and press the button. Direct sunlight or very bright light could affect the ability of the RSE transmitter to receive signals from the remote control. Check the batteries if the remote control does not seem to be working. See “Battery Replacement” later in this section. Objects blocking the line of sight could also affect the function of the remote control.


6-38


Infotainment System


If a CD, DVD, or MP3 disc is in the Radio DVD slot, the remote control O button can be used to turn on the video screen display and start the disc. The infotainment system can also turn on the video screen display. See CD/DVD Player on page 6‑21 or the separate navigation system manual for more information. Notice: Storing the remote control in a hot area or in direct sunlight can damage it, and the repairs will not be covered by the warranty. Storage in extreme cold can weaken the batteries. Keep the remote control stored in a cool, dry place.


Remote Control Buttons O (Power): Press to turn the video screens on and off. P (Illumination): Press to turn the remote control backlight on. The backlight times out after several seconds if no other button is pressed.


v (Title): Press to return to the main menu of the DVD. This function could vary for each disc. y (Main Menu): Press to access the DVD menu. The DVD menu is different on every DVD. Use the navigation arrows to move the cursor. After making a selection press the enter button. This button only operates when using a DVD. n , q, p, o (Menu Navigation Arrows): Use the arrow buttons to navigate through a menu. r (Enter): Press to select the highlighted choice in any menu. z (Display Menu): Press to adjust the brightness, screen display mode, and display the language menu. q (Return): Press to exit the current active menu and return to the previous menu. This button operates only when the display menu or a DVD menu is active.


c (Stop): Press to stop playing, rewinding, or fast forwarding a DVD. Press twice to return to the beginning of the DVD. s (Play/Pause): Press to start playing a DVD. Press to pause a DVD while it is playing. Press again to continue playing. Depending on the infotainment system in the vehicle, DVD playback may be slowed down by pressing s then [. Reverse slow play by pressing s then r. Press s again to cancel slow play. t (Previous Track/Chapter): Press to go to the start of the current track or chapter. Press again to go to the previous track or chapter. This button may not work when the DVD is playing the copyright information or the previews.


Infotainment System 6-39


} 10 (Double Digit Entries) (If Available): Press this button to select chapter or track numbers greater than 9. Press this button before inputting the number. 1 through 0 (Numeric Keypad): The numbered keypad provides the capability of direct chapter or track number selection.


Replacing the Remote Control If the remote control becomes lost or damaged, a new universal remote control can be purchased. Use a Toshiba® code set for replacement universal remote controls.


e (Audio): Press to change audio tracks on DVDs that have this feature when the DVD is playing. { (Subtitles): Press to turn ON/OFF subtitles and to move through subtitle options when a DVD is playing. AUX (Auxiliary): Press to switch the video display between the DVD player and an auxiliary source. d (Camera): Press to change the camera angle on DVDs that have this feature when the DVD is playing. \ (Clear) (If Available): Press this button within three seconds after inputting a numeric selection, to clear all numeric inputs.


u (Next Track/Chapter): Press to go to the beginning of the next chapter or track. This button might not work when the DVD is playing the copyright information or the previews. r (Fast Reverse): Press to quickly reverse the DVD or CD. To stop fast reversing a DVD video, press s. To stop fast reversing a DVD audio or CD, release r. This button might not work when the DVD is playing the copyright information or the previews. [ (Fast Forward): Press to fast forward the DVD or CD. To stop fast forwarding a DVD video, press s To stop fast forwarding a DVD audio or CD, release [. This button might not work when the DVD is playing the copyright information or the previews.


6-40


Infotainment System


Battery Replacement To change the remote control batteries: 1. Slide back the rear cover on the


remote control.


2. Replace the two batteries in the


compartment.


3. Replace the battery cover. Remove the batteries from the remote control if unused for an extended period of time.


Tips and Troubleshooting Chart


Problem


Recommended Action


No power.


The picture does not fill the screen. There are black borders on the top and bottom or on both sides or it looks stretched out. In auxiliary mode, the picture moves or scrolls. The remote control does not work.


After stopping the player, I push Play but sometimes the DVD starts where I left off and sometimes at the beginning.


The ignition might not be turned to ON/RUN or in ACC/ACCESSORY. Check the display mode settings in the setup menu by pressing the display menu button on the remote control. Check the auxiliary input connections at both devices. Check to make sure there is no obstruction between the remote control and the transmitter window. Check the batteries to make sure they are not dead or installed incorrectly. If the stop button was pressed one time, the DVD player resumes playing where the DVD was stopped. If the stop button was pressed two times the DVD player begins to play from the beginning of the DVD.


Tips and Troubleshooting Chart (cont'd) Problem


Recommended Action


The auxiliary source is running but there is no picture or sound.


Sometimes the wireless headphone audio cuts out or buzzes.


I lost the remote and/or the headphones. The DVD is playing, but there is no picture or sound.


Check that the RSE video screen is in the auxiliary source mode by pressing the AUX button on the remote control. Check the auxiliary input connections at both devices. Check for obstructions, low batteries, reception range, and interference from cellular telephone towers or by using a cellular telephone in the vehicle. Check that the headphones are on correctly using the L (left) and R (right) on the headphones. Check that the headphones are positioned properly with the headband across the top of the head. See your dealer/retailer for assistance. Check that the RSE video screen is sourced to the DVD player by pressing the AUX button on the remote control.


Infotainment System 6-41


DVD Display Error Messages The DVD display error message depends on which radio the vehicle has. The video screen may display one of the following: Disc Load/Eject Error or Mechanical Error: There are disc load or eject problems. Disc Format Error or Unknown Format: The disc is inserted with the disc label wrong side up, or if the disc is damaged. Disc Region Error or Disc Error: The disc is not from a correct region. No Disc Inserted: No disc is present when the Z EJECT or MEM/DVD/AUX button is pressed on the radio.


6-42


Infotainment System


DVD Distortion Video distortion can occur when operating cellular phones, scanners, CB radios, Global Position Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It might be necessary to turn off the DVD player when operating one of these devices in or near the vehicle. *Excludes the OnStar® System. Cleaning the RSE Seatback Console Use only a clean cloth dampened with clean water to clean the RSE seatback console surface. Cleaning the Video Screen Use only a clean cloth dampened with clean water. Use care when touching or cleaning the screen as damage could result.


Phone


Bluetooth (Overview) Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands‐Free Profile to make and receive phone calls. The infotainment system and voice recognition are used to control the system. The system can be used while the ignition is in ON/RUN or ACC/ACCESSORY. The range of the Bluetooth system can be up to 9.1 m (30 ft.). Not all phones support all functions and not all phones work with the Bluetooth system. See www.gm.com/bluetooth for more information about compatible phones. Bluetooth Controls Use the buttons located on the infotainment system and the steering wheel to operate the Bluetooth system.


Steering Wheel Controls b / g (Push To Talk): Press to answer incoming calls, to confirm system information, and to start voice recognition. $ / c (Mute/End Call): Press to end a call, reject a call, or to cancel an operation.


Infotainment System Controls For information about how to navigate the menu system using the infotainment controls, see Operation on page 6‑7. 5 (Phone): Press to enter the Phone main menu. Voice Recognition The voice recognition system uses commands to control the system and dial phone numbers. Noise: The system may not recognize voice commands if there is too much background noise.


When to Speak: A tone sounds to indicate that the system is ready for a voice command. Wait for the tone and then speak. How to Speak: Speak clearly in a calm and natural voice. Audio System When using the Bluetooth system, sound comes through the vehicle's front audio system speakers and overrides the audio system. Use the VOL/ O knob during a call to change the volume level. The adjusted volume level remains in memory for later calls. The system maintains a minimum volume level. Other Information The Bluetooth® word mark and logos are owned by the Bluetooth® SIG, Inc. and any use of such marks by General Motors is under license. Other trademarks and trade names are those of their respective owners. See Radio Frequency Statement on page 12‑16 for FCC information.


Bluetooth (Infotainment Controls) For information about how to navigate the menu system using the infotainment controls, see Operation on page 6‑7 . Pairing A Bluetooth enabled cell phone must be paired to the Bluetooth system first and then connected to the vehicle before it can be used. See the cell phone manufacturer user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected, calls will be made using OnStar® Hands‐Free Calling, if available. Refer to the OnStar Owner's Guide for more information. The pairing process can be started by using the voice recognition system or the controls on the infotainment system.


Infotainment System 6-43


Pairing Information: . Up to five cell phones can be


paired to the Bluetooth system. The pairing process is disabled when the vehicle is moving. The Bluetooth system links with the first available paired cell phone in the order the phone was paired.


. Only one paired cell phone can be connected to the Bluetooth system at a time.


. Pairing should only need to be


completed once, unless changes to the pairing information have been made or the phone is deleted.


To link to a different paired phone, see “Linking to a Different Phone” later in this section.


6-44


Infotainment System


Pairing a Phone 1. Press the CONFIG button. 2. Select Phone Settings. 3. Select Bluetooth. 4. Select Pair Device (Phone).


A four digit PIN number appears on the display.


5. Start the pairing process on the cell phone that will be paired to the vehicle. Reference the cell phone manufacturers user guide for information on this process. Locate the device named “General Motors” in the list on the cell phone and follow the instructions on the cell phone to enter the four digit PIN number provided by the system.


6. The system prompts for a name for the phone and confirms the name provided. This name is used to indicate which phone is connected.


7. The system responds with “ has been successfully paired” after the pairing process is complete.


8. Repeat Steps 1 through 7 to pair


additional phones.


Listing All Paired and Connected Phones 1. Press the CONFIG button. 2. Select Phone Settings. 3. Select Bluetooth. 4. Select Device List.


Deleting a Paired Phone 1. Press the CONFIG button. 2. Select Phone Settings. 3. Select Bluetooth. 4. Select Device List. 5. Select the phone to delete and follow the on screen prompts.


Linking to a Different Phone To link to a different phone, the new phone must be in the vehicle and available to be connected to the bluetooth system before the process is started. 1. Press the CONFIG button. 2. Select Phone Settings. 3. Select Bluetooth. 4. Select Device List. 5. Select the new phone to link to


and follow the on screen prompts. If delete is selected, the highlighted phone will be deleted.


Infotainment System 6-45


Making a Call


Radio with CD


1. Press the 5 / 0 button.


2. Enter the character sequence.


See “Entering a Character Sequence” in Operation on page 6‑7 for more information.


3. Select Call to start dialing the


number.


Radio with CD/DVD and MEM


1. Press the 5 / 0 button.


2. Select Enter number. 3. Enter the character sequence.


See “Entering a Character Sequence” in Operation on page 6‑7 for more information.


4. Select Call to start dialing the


number.


Accepting or Declining a Call When a call is received, the infotainment system mutes and a ring tone is heard in the vehicle.


Declining a Call Turn the MENU/SEL knob to Decline and press the MENU/SEL knob.


Accepting a Call Turn the MENU/SEL knob to Answer and press the MENU/SEL knob.


Declining a Call Turn the MENU/SEL knob to Decline and press the MENU/SEL knob. Call Waiting Call waiting must be supported on the bluetooth phone and enabled by the wireless service carrier to work.


Accepting a Call Turn the MENU/SEL knob to Answer and press the MENU/SEL knob.


Switching Between Calls (Call Waiting Calls Only) To switch between calls: 1. Press the MENU/SEL knob. 2. Select Switch Call from


the menu.


Conference Calling Conference calling and three way calling must be supported on the bluetooth phone and enabled by the wireless service carrier to work. To start a conference while in a current call: 1. Press the MENU/SEL knob. 2. Select Enter Number.


6-46


Infotainment System


3. Enter the character sequence then select Call. See “Entering a Character Sequence” in Operation on page 6‑7 for more information.


4. After the call has been placed, press the MENU/SEL knob and choose Merge Calls.


5. To add more callers to the


conference call, repeat Steps 1 through 4. The amount of callers that can be added are limited by your wireless service carrier.


Ending a Call Press the MENU/SEL knob and select Hang Up.


Muting a Call


To Mute a Call Press the MENU/SEL knob and select Mute Call.


To Cancel Mute Press the MENU/SEL knob and select Mute Call. Dual Tone Multi-Frequency (DTMF) Tones The in‐vehicle Bluetooth system can send numbers during a call. This is used when calling a menu driven phone system. 1. Press the MENU/SEL knob and


select Enter Number.


2. Enter the character sequence,


see “Entering a Character Sequence” in Operation on page 6‑7 for more information.


Bluetooth (Voice Recognition)


Pairing A Bluetooth cell phone must be paired to the Bluetooth system and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected, calls will be made using OnStar® Hands‐Free Calling, if available. Refer to the OnStar owner's guide for more information. The pairing process can be started by using the voice recognition system or the controls on the infotainment system.


Pairing Information: . Up to five cell phones can be


paired to the Bluetooth system. The pairing process is disabled when the vehicle is moving. The Bluetooth system links with the first available paired cell phone in the order the phone was paired.


. Only one paired cell phone can be connected to the Bluetooth system at a time.


. Pairing only needs to be


completed once, unless the pairing information changes or the phone is deleted.


To link to a different paired phone, see Linking to a Different Phone later in this section.


Pairing a Phone 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Bluetooth”. The system responds “Bluetooth ready”, followed by a tone.


3. Say “Pair”. The system responds with instructions and a four‐digit PIN number. The PIN number will be used in Step 4.


Infotainment System 6-47


4. Start the pairing process on the cell phone that will be paired to the vehicle. Reference the cell phone manufacturers user guide for information on this process. Locate the device named “General Motors” in the list on the cell phone and follow the instructions on the cell phone to enter the four‐digit PIN number that was provided in Step 3.


5. The system prompts for a name for the phone. This name will be used to indicate which phone is connected. The system confirms the name.


6. The system responds with “ has been successfully paired” after the pairing process is complete. 7. Repeat Steps 1 through 7 for


additional phones to be paired.


6-48


Infotainment System


Listing All Paired and Connected Phones 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Bluetooth”. The system responds “Bluetooth ready”, followed by a tone.


3. Say “List”. The system lists all the paired Bluetooth devices. The system will respond “is connected” if a phone is connected to the vehicle.


Deleting a Paired Phone 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Bluetooth”. The system responds “Bluetooth ready”, followed by a tone.


3. Say “Delete”. The system asks which phone to delete followed by a tone.


4. Say the name of the phone to be deleted. If the phone name is unknown, use the “List” command for a list of all paired phones. The system responds “Would you like to delete ? Yes or No”, followed by a tone.


5. Say “Yes” to delete the phone.


The system responds “OK, deleting ”.


Linking to a Different Phone 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Bluetooth”. The system responds “Bluetooth ready”, followed by a tone.


3. Say “Change phone”. The


system responds “Please wait while I search for other phones”.


Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Store”. The system responds “Store, number please”, followed by a tone.


If another phone is found, the response will be “ is now connected”. If another phone is not found, the original phone remains connected.


Storing Name Tags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve phone numbers: . Store . Digit Store . Directory


Infotainment System 6-49


3. Say the complete phone number


to be stored at once with no pauses.


If the system recognizes the number, the response is “OK, Storing”. If the system does not recognize the phone number, the response is “Store ”. “Please say yes or no”. If the number is correct, say “Yes”. If the number is not correct, say “No”. The system will ask for the number again.


4. After the system stores the phone number, it responds “Please say the name tag”, followed by a tone.


6-50


Infotainment System


5. Say a name tag for the phone


number. The name tag is recorded and the system responds “About to store . Does that sound OK?”.


If the name tag does not sound correct, say “No” and repeat Step 5. If the name tag sounds correct, say “Yes” and the name tag is stored. After the number is stored the system returns to the main menu.


Using the Digit Store Command The digit store command allows a phone number to be stored by entering the digits individually. 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone.


For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Digit Store”. The system responds with “Please say the first digit to store”, followed by a tone.


3. Say the first digit to be stored.


The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete.


If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number. To hear all of the numbers recognized by the system, say “Verify” at any time.


4. After the complete number has been entered, say “Store”. The system responds “Please say the name tag”, followed by a tone.


5. Say a name tag for the phone


number. The name tag is recorded and the system responds “About to store . Does that sound OK?”.


If the name tag does not sound correct, say “No” and repeat Step 5. If the name tag sounds correct, say “Yes” and the name tag is stored. After the number is stored the system returns to the main menu.


Using the Directory Command The directory command lists all of the name tags stored by the system. To use the directory command: 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Directory”. The system


responds “Directory” and lists all stored name tags. The system returns to the main menu when the list is complete.


Deleting Name Tags The system uses the following commands to delete name tags: . Delete . Delete all name tags


Using the Delete Command The delete command is used to delete specific name tags. To delete name tags: 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


Infotainment System 6-51


2. Say “Delete”. The system


responds “Delete, please say the name tag”, followed by a tone.


3. Say the name tag to be deleted.


The system responds “Would you like to delete, ? Please say yes or no”.


If the name tag is correct, say “Yes” to delete the name tag. The system responds with “OK, deleting , returning to the main menu.” If the name tag is incorrect, say “No”. The system responds with “No. OK, let's try again, please say the name tag.”


6-52


Infotainment System


Using the Delete All Name Tags Command The Delete All Name Tags command deletes all stored phone book name tags and route name tags for OnStar, if stored. To delete all name tags: 1. Press b / g .


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Delete all name tags”. The system responds “You are about to delete all name tags stored in your phone directory and your route destination directory. Are you sure you want to do this? Please say yes or no.”


Say “Yes” to delete all name tags. Say “No” to cancel the function and return to the main menu.


Making a Call Calls can be made using the following commands: . Dial . Digit Dial . Call . Re‐dial


Using the Dial Command 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Dial”. The system responds


“Dial using . “Number please”, followed by a tone.


3. Say the entire number without


pausing.


If the system recognizes the number, it responds with “OK, Dialing” and dials the number. If the system does not recognize the number, it confirms the numbers followed by a tone. If the number is correct, say “Yes”. The system responds “OK, Dialing” and dials the number. If the number is not correct, say “No”. The system will ask for the number again.


Using the Digit Dial Command 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Digit Dial”. The system


responds “Digit dial using , please say the first digit to dial”, followed by a tone.


Infotainment System 6-53


3. Say the digits to be dialed one at a time. The system repeats back the digit it heard followed by a tone.


4. Continue entering digits until the number to be dialed is complete. After the whole number has been entered, say “Dial”. The system responds “OK, Dialing” and dials the number.


If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number. To hear all of the numbers recognized by the system, say “Verify” at any time.


6-54


Infotainment System


Using the Call Command 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Call”. The system responds


“Call using . Please say the name tag”, followed by a tone.


3. Say the name tag of the person


to call.


If the system recognizes the name tag it responds “OK, calling, ” and dials the number. If the system does not recognize the name tag, it confirms the name tag followed by a tone. If the name tag is correct, say “Yes”. The system responds with “OK, calling, ” and dials the number. If the name tag is not correct, say “No”. The system will ask for the name tag again.


Once connected, the person called will be heard through the audio speakers.


Using the Re‐dial Command 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds with “Ready”, followed by a tone.


2. After the tone, say “Re‐dial”. The system responds “Re‐dial using ” and dials the last number called from the connected Bluetooth phone.


Once connected, the person called will be heard through the audio speakers.


Receiving a Call When an incoming call is received, the audio system mutes and a ring tone is heard in the vehicle. . Press b g to answer the call. . Press c / $ to ignore a call. Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier. . Press b g to answer an


incoming call when another call is active. The original call is placed on hold.


. Press b g again to return to the


original call. To ignore the incoming call, no action is required.


. Press c / $ to disconnect the current call and switch to the call on hold.


Three‐Way Calling Three‐way calling must be supported on the Bluetooth phone and enabled by the wireless service carrier. 1. While on a call, press b g. The system responds with “Ready”, followed by a tone.


2. Say “Three‐way call”.


The system responds with “Three‐way call, please say dial or call”.


3. Use the dial or call command to dial the number of the third party to be called.


4. Once the call is connected,


press b g to link all the callers together.


Ending a Call Press c / $ to end a call.


Infotainment System 6-55


Muting a Call During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them.


To Mute a call 1. Press b g. The system


responds “Ready”, followed by a tone.


2. Say “Mute Call”. The system


responds “Call muted”.


To Cancel Mute 1. Press b g. The system


responds “Ready”, followed by a tone.


2. After the tone, say “Mute Call”.


The system responds “Resuming call”.


6-56


Infotainment System


Transferring a Call Audio can be transferred between the in‐vehicle Bluetooth system and the cell phone.


To Transfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press b g . The system


responds “Ready”, followed by a tone.


2. Say “Transfer Call.” The system responds “Transferring call” and the audio transfers to the cell phone.


To Transfer Audio to the In-Vehicle Bluetooth System The cell phone must be paired and connected with the Bluetooth system before a call can be transferred. The connection process can take up to two minutes after the ignition is turned to ON/RUN or ACC/ACCESSORY.


For vehicles without a navigation system, press b g during a call with the audio on the cell phone, the audio transfers to the vehicle. For vehicles with a navigation system, press b g during a call with the audio on the cell phone. If the audio does not transfer to the vehicle, use the audio transfer feature on the cell phone. See the cell phone manufacturers user guide for more information. Voice Pass-Thru Voice pass‐thru allows access to the voice recognition commands on the cell phone. See the cell phone manufacturers user guide to see if the cell phone supports this feature.


To access contacts stored in the cell phone: 1. Press b / g.


For vehicles without a navigation system, the system responds “Ready”, followed by a tone. For vehicles with a navigation system, the system responds with a tone. After the tone say “Hands Free”. The system responds “Ready”, followed by a tone.


2. Say “Bluetooth”. The system responds “Bluetooth ready”, followed by a tone.


3. Say “Voice”. The system responds “OK, accessing ”.


The cell phone's normal prompt messages will go through its cycle according to the phone's operating instructions.


Dual Tone Multi-Frequency (DTMF) Tones The in‐vehicle Bluetooth system can send numbers and the numbers stored as name tags during a call. Use this feature when calling a menu driven phone system. Account numbers can also be stored for use.


Sending a Number During a Call 1. Press b g. The system


responds “Ready”, followed by a tone.


2. Say “Dial”. The system responds


“Say a number to send tones”, followed by a tone.


3. Say the number to send.


If the system recognizes the number, it responds “OK, Sending Number” and the dial tones are sent and the call continues.


If the system does not recognize the number, it responds “Dial Number, please say yes or no?”, followed by a tone. If the number is correct, say “Yes”. The system responds “OK, Sending Number” and the dial tones are sent and the call continues.


Sending a Stored Name Tag During a Call 1. Press b g. The system


responds “Ready”, followed by a tone.


2. Say “Send name tag.” The


system responds “Say a name tag to send tones”, followed by a tone.


3. Say the name tag to send.


If the system recognizes the number, it responds “OK, Sending ” and the dial tones are sent and the call continues.


Infotainment System 6-57


If the system does not recognize the name tag, it responds “Dial , please say yes or no?”, followed by a tone. If the name tag is correct, say “Yes”. The system responds with “OK, Sending ” and the dial tones are sent and the call continues.


Clearing the System Unless information is deleted out of the in‐vehicle Bluetooth system, it will be retained indefinitely. This includes all saved name tags in the phone book and phone pairing information. For information on how to delete this information, see the previous sections on Deleting a Paired Phone and Deleting Name Tags.


6-58


Infotainment System


Bluetooth (Navigation) For information about how to navigate the menu system using the infotainment controls, see “Overview” under Introduction, in the Navigation supplement. Bluetooth Pairing To make calls with a Bluetooth cell phone through your vehicle, it must be paired to the vehicle's Bluetooth system first and then connected to the vehicle before it can be used. Refer to the cell phone manufacturer's user guide for Bluetooth pairing instructions. If a Bluetooth phone is off or not connected, calls will automatically be made using the OnStar® Hands‐Free Calling feature, if available. Refer to the OnStar owner's guide for more information about OnStar Hands-Free Calling.


The pairing process can be started by using the voice recognition system or the controls on the infotainment system. Pairing Information: . Up to five cell phones can be


paired to the Bluetooth system. The pairing process is disabled when the vehicle is moving. The Bluetooth system automatically links with the paired cell phone in the order the phones are listed in the device list.


. Only one paired cell phone can


be connected to the vehicle's Bluetooth system at a time.


. Pairing should only need to be


completed once.


Pairing a Phone 1. Press the CONFIG hard key


repeatedly until the Phone menu is shown or touch the Phone tab on the screen.


2. Select the Bluetooth submenu.


Infotainment System 6-59

Loading...
x