1993 Chevrolet Camaro Owners Manual

rhis is normal because the system is designed to cycle the compressor on and Dff to keep the desired cooling and help fuel economy.

Cooling The air conditioner works best if you keep your windows closed. On very hot days, open the windows just long enough for the hot air to escape. 1. Turn the air control knob to A/C for

normal cooling. For faster cooling move the knob to MAX.

2. Turn the temperature control knob to

a comfortable setting.

3. Turn the fan control knob to the right.

Comfort Controls & Audio Systems

(OPTION) The rear window defogger uses a warming grid to remove fog from the rear window. Press the right side of the switch to turn on the defogger. An indicator light will come on to remind you that the defogger is on. The defogger will turn off automatically after about ten minutes of use. If you turn it on again, the defogger will operate for about five minutes only. You can also turn the defogger off by pressing the left side of the switch.

Do not attach anything like a temporary vehicle license or a decal across the defogger grid on the rear window.

lsomething else sharp on the inside of the rear window. ^If you do, you could cut or damage the warming grid, and the repairs wouldn't be

System Your Chevrolet's flow-through ventilation system supplies outside air into the vehicle when it is moving. Outside air will also enter the vehicle when the heater or the air conditioning fan is running.

D Keep the air path under the front seats

clear of objects. This helps air to circulate throughout your vehicle.

Audio Systems

Your Delco@ audio system has been designed to operate easily and give years of listening pleasure. But you will get the most enjoyment out of it if you acquaint yourself with it first. Find out what your Delco@ system can do and how to operate all its controls, to be sure you’re getting the most out of the advanced engineering that went into it.

Ventilation Tips

Keep the hood and front air inlet free of ice, snow, or any other obstruction (such as leaves). The heater and defroster will work far better, reducing the chance of fogging the inside of your windows. When you enter a vehicle in cold weather, turn the fan control knob to the right for a few moments before driving off. This helps clear the intake ducts of snow and moisture, and reduces the chance of fogging the inside of your windows.

Comfort Controls & Audio Systems

noise is almost undetectable

until it is too late. Your hearing can adapt to higher volumes of sound. sure you can add what you want. If Sound that Seems normal can be Ioud and harmful to your hearing. Take precautions by adjusting the volume control on your radio to a safe sound level before your hearing adapts to it. To help avoid hearing damage: a Adjust the volume control to

you can, it’s very important to do it properly. Added sound equipment may interfere with the operation of your vehicle’s engine, Delco@ radio or other systems, and even damage them. And, your vehicle’s systems may interfere with the operation of sound equipment that has been added improperly. So, before adding sound equipment, check with your d er

31

the lowest setting.

loss or

and

I, Increase volume slowly until

you hear comfortably clearly.

1116

Clock

Setting

AM/FM Stereo with Cassette Tape Player 1. Press SET. 2. Within five seconds, press and hold

until the correct hour

SEEK appears.

3. Press and hold SEEK A until the

correct minute appears.

Delco/Bose AM/FM Stereo with Compact Disc Player 1. Press SET. 2. Within five seconds, press and hold

SEEK 4 until the correct hour

3. Press and hold SEEK correct minute appears.

until the

AMIFM Stereo with Cassette Tape Player

To Play the Radio Turn the upper knob to turn the system on or off.

Volume Turn the upper knob to adjust the volume.

AM-FM Press the lower knob to get AM or FM. The lighted display shows your selection.

Tune Turn the lower knob to choose radio stations.

Recall Press the upper knob to recall the station being played or the clock display.

Seek Press SEEK v or A and the radio will tune to the next lower or higher station and stay there.

Scan The scan function uses the same two buttons as the seek function. To go to the next higher station and stay there for a few seconds, press and hold SEEK A and then press SEEK v for an instant. To go to the next lower station and stay there for a few seconds, press and hold SEEK v and then press SEEK A for an instant. To stop the scan function, press either SEEK A or v.

Comfort Controls & Audio Systems

Setting the Tone Bass: Slide the BASS lever up to hear more bass, Treble: Slide the TREB lever up to hear more treble. If a station is weak and noisy, move TREB down to reduce the noise.

Pushbuttons The four pushbuttons let you return to your favorite stations. You can preset up to 14 stations (7 AM and 7 FM). To set the pushbuttons for up to eight stations (four AM and four FM), just: 1. Tune in the station. 2. Press SET. (“SET” will appear on the

display for about five seconds.)

3. Within five seconds, press one of the four pushbuttons. Whenever you press that button, the preset station will return.

Repeat these steps for each pushbutton.

You can preset three more stations on each band by pressing a pair of buttons next to each other at the same time. Just: 1. Tune in the station. 2. Press SET. (“SET” will appear on the

display for about five seconds.) 3. Within five seconds, press two

pushbuttons next to each other at the same time. Whenever you press that pair of buttons, the preset station will return.

Repeat these steps for each pair of pushbuttons.

I

Adjusting the Speakers Balance: Turn the balance control behind the upper knob to move the sound between the right and left speakers if you do not have the Delco/Bose system. With the Delco/Bose system, Your speakers are electronically balanced. Fade: Turn the fade control behind the lower knob to move the sound between the front and rear speakers.

To Play a Cassette Tape Your tape player is built to work best with tapes that are 30 to 45 minutes long on each side. Tapes longer than that are so thin they may not work well in this player. The longer side with the tape visible goes in first. If you hear nothing or hear just a garbled sound, it may not be in squarely. Press STOP-EJECT to remove the tape and start over. Once the tape is playing, use the upper and lower knobs for volume and balance, just as you do for radio. The arrows show which side of the tape is playing.

to rapidly rewind or

Press 4 or advance the tape. Press STOP-EJECT to stop the tape.

119

Comfort Controls & Audio Systems

Automatic Program Search When you push APS you can go to the beginning of a new selection. 0 To go forward to the beginning of the

next selection, press To go back to the beginning of the current selection press 4 . Push 4 again to go to the beginning of the previous selection.

... 120

Program Press the upper knob on your system to switch from one side of the tape to the other. Your cassette tape player can play continuously because the player has an auto-reverse feature.

Eject Press STOP-EJECT to remove the tape or stop the tape and switch to the radio.

Cr02 (Delco/Bose System) The Cr02 button lets you set the system for the type of cassette being used. If you are using chrome or metal tapes, push Cr02 in. If you are using standard tapes, make sure CrO2 is out. Noise Reduction (Delco/Bose System) Your sound system has the Dolby@ automatic noise reduction feature. Dolby@ Noise Reduction is manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.

Deico/Bose AM/FM Stereo with Compact Disc Player

To Play the Radio Turn the upper knob to turn the system on oi off.

Volume Turn the upper knob to ad-just the volume.

AM-FM Press the lower knob to get AM. FMI or FM2.

Tune Turn the lower knob to choose radio stations.

Seek Press SEEK 4 or lower or higher station and stay there

to go to the next

Scan Press SCAN to hear each station for a few seconds. When you want to stop scanning. press SCAN again or the upper knob.

Pushbuttons The five pushbuttons let you return to your favorite stations. To set the pushbuttons for up to 15 stations ( 5 AM, 5 FMI and 5 FM2), just: 1. Press the lower knob to choose AM,

FM 1 or FM2.

2. Tune in the station. 3. Press SET. (“SET” will appear on the

display for about five seconds.)

4. Within five seconds, press one of the pushbuttons. Whenever you press that button, the preset station will return. Repeat these steps for each pushbutton.

121

Comfort Controls & Audio Systems

Setting the Tone Bass: Press BASS A or BASS to hear more or less bass. Treble: Press TREB A or TREB v to hear more or less treble. For the clearest sound, keep both of these adjusted all the way up. If a station is weak and noisy, press TREB v to reduce the noise. Adjusting the Speakers Balance: Turn the balance control behind the upper knob to move the sound between the right and left speakers.

Fade: Turn the fade control behind the lower knob to move the sound between the front and rear speakers. I’o Play a Compact Disc Before you begin, please note: don’t use :he mini-discs that are called “singles.” rhey won’t eject. Use full-size compact jiscs. With the audio system on, insert a disc into the slot with the label side up. “CD” will appear on the display and track 1 will begin to play.

If the disc comes back out and “ERR” appears on the display, it could be that:

The disc is upside down. It is dirty, scratched, or wet. There’s too much moisture in the air. You are driving on a very rough road. The temperature is too hot or too cold.

... 122

Recall Press RCL to see what track is playing. Press it again within five seconds to see how long it has been playing. The track number also appears when the disc is inserted.

To Play the Next Selection Press NEXT to hear the next track now (instead of waiting until the present track is finished). If you press and hold this button or press it more than once, the disc will advance further.

To Replay the Current Selection Press PREV to hear a track again. If you press and hold this button, or press it more than once, the disc will return to previous tracks.

Reverse Press and hold REV to rapidly return to a favorite passage. Release it to play the passage.

Fast Forward Press and hold FWD to quickly advance within a track. Release it to resume playing.

Scan Press SCAN to listen to each track for about 10 seconds. Press RDM or SCAN to stop the scanning.

Compression Press COMP to make loud and soft passages more nearly equal in volume.

Random Press RDM to hear a random selection of tracks.

Comfort Controls & Audio Systems

To Stop the Disc Player

Turn the power off or turn the ignition key off. The disc stays in the player and will resume playing at the point where it stopped. Press ST-PL to stop playing the disc and switch to radio. Press ST-PL to restart the disc at the point where it stopped. Press EJCT to eject the disc and the radio will play. The disc will start playing at track 1 when you reinsert it.

Theft-Deterrent Feature Delco-Loc I1 is a security feature for the compact disc player. It can be used or ignored. If ignored, the system functions normally. If it is used, your system won’t be usable if it’s ever stolen.

Setting Your Security Code The instructions below tell you how to enter a security code into the system. If your vehicle loses battery power for any reason, you must enter the security code again before the system will turn on. 1. Write down any six digit number and

keep it in a safe place.

2. Turn the ignition switch to the Acc

or Run position.

3. Turn the audio system off. 4. Press and hold 1 and 4 together until

“---” shows on the display.

I . 9 124

You are now ready to enter your security code. Don’t wait more than 15 seconds between steps. 5. Press SET and “000” will appear on

the display.

6. Press SCAN and hold until the first digit of your code appears. Release the button.

7. Press SEEK 4 or b and hold until the second and third digits of your code appear. Release the button.

8. Press the lower knob and “000’ will appear. Now you are ready to enter the last three digits of your code.

9. Press SCAN and hold until the

fourth digit of your code appears. Release the button.

10. Press SEEK 4 or b and hold until

the fifth and sixth digits of your code appear. Release the button.

11. Press the lower knob. “rEP’ will appear for five seconds, and then “000” will appear.

12. Repeat steps 6 through 11. “SEC” will appear. This means that your audio system is secured.

Shutting Off the Theft-Deterrent Feature If your audio system is secured (“SEC” shows on display) and you wish to disable it, enter your security code as follows, pausing no more than 15 seconds between steps: 1. Turn the ignition on. Make sure the

audio system is off. The time will show on the display.

2. Press 1 and 4 together for five

seconds. “SEC” will show on the display.

3. Press SET. “000” will appear on the

display.

Comfort Controls & Audio Systems

4. Press SCAN and hold until the first

digit of your code appears. Release the button.

5. Press SEEK 4 or b and hold until the

second and third digits appear. Release the button.

6. Press the lower knob.“000” will

appear on the display.

7. Press SCAN and hold until the fourth digit of your security code appears. Release the button.

126

m m .

8. Press SEEK 4 or b and hold until the

fifth and sixth digits of your code appear. Release the button.

9. Press the lower knob. If ”---” shows, you have shut off the theft-deterrent feature. If “SEC” shows, your audio system is still secured.

NOTE: If you lose or forget your security code. see your dealer for assistance.

Unlocking the Audio System after a Power Failure If power is disrupted to the audio system while in the “SEC” mode, the unit will not work and “LOC” will show on the display whenever the ignition is on. To unlock the unit: 1. Press SET. “000” will appear on the

display.

2. Press SCAN and hold until the first

digit of your code appears. Release the button.

3. Press SEEK 4 or b and hold until the

second and third digits appear. Release the button.

4. Press the lower knob.“000” will

appear on the display.

5. Press SCAN and hold until the fourth digit of your code appears. Release the button.

6. Press SEEK 4 or

and hold until the

fifth and sixth digits of your code appear. Release the button.

7. Press the lower knob. “SEC” will

appear and the unit will work. If “LOC” shows, the numbers did not match and the unit is still locked.

How to Change Your Security Code You can change your security code by following these steps: 1. Using your old code, follow the

directions given under “Shutting Off the Theft-Deterrent Feature.’’

2. Repeat directions of “Setting Your

Security Code” with your new security code.

Understanding Radio Reception FM Stereo FM stereo will give you the best sound. But FM signals will reach only about 10 to 40 miles (16 to 65 km). And, tall buildings or hills can interfere with FM signals, causing the sound to come and go.

AM The range for most AM stations is greater than for FM, especially at night. The longer range, however, can cause stations to interfere with each other. AM can pick up noise from things like storms and power lines. Try reducing the treble to reduce this noise if you ever get it.

1 2 7 - - -

Comfort Controls & Audio Systems

AM Stereo This means the Delco@ system can receive C-QUAM@ stereo broadcasts. Many AM stations around the country use C-QUAM@ to produce stereo, though some do not. (C-QUAM@ is a registered trademark of Motorola, Inc.) If your Delco@ system can get C-QUAM@, your “STEREO” light will come on when you’re receiving it.

Care of Your Cassette Tape Player A tape player that is not cleaned regularly can cause reduced sound quality, ruined cassettes, or a damaged mechanism. Cassette tapes should be stored i n their cases away from contaminants, direct sunlight, and extreme heat. If they aren’t. they may not operate properly or cause failure of the tape player. Your tape player should be cleaned regularly each month or after every IS hours of use. If you notice a reduction i n sound quality. try a known good cassette to see if the tape or the tape player is a1 fault. If this other cassette has no improvenlent i n sound qualily. clean the tape player.

Clean your tape player with a wiping-action, non-abrasive cleaning cassette, and follow the directions provided with it. Cassettes are subject to wear and the sound quality may degrade over time. Always make sure that the cassette tape is i n good condition before you have your tape player serviced.

I Care of Your Compact Discs

Handle discs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge. Be sure never to touch the signal surface when handling discs. Pick up discs by grasping the outer edges or the edge of the hole and the outer edge.

Fixed Mast Antenna The fixed mast antenna can withstand most car washes without being damaged. If the mast should ever become slightly bent, you can straighten it out by hand. If the mast is badly bent, as it might be by vandals, you should replace it. Check every once in a while to be sure the mast is still tightened to the fender.

Notes

... 130

Part 4 Your Driving and the Road

H e r e you’ll find information about driving on different kinds of roads and in varying weather conditions . We’ve also included many other useful tips on driving .

Roadsigns ....................................................... t ........................... Defensive Driving ..................... DrunkenDriving .................................................. Control of a Vehicle ................................................ DrivingatNight ................................................... Driving in the Rain ................................................. Driving in Fog, Mist and Haze ........................................ CityDriving ...................................................... FreewayDriving .................................................. Driving a Long Distance ............................................ HillandMountainRoads ............................................ ParkingonHills ................................................... Winter Driving .................................................... Towing a Trailer ...................................................

132 136 137 140 153 155 158 160 161 163 165 168 170 173

Your Driving and the Road

Road Sigpts

The road signs you see everywhere are coded by color, shape and symbols. It’s a good idea to know these codes so that you can quickly grasp the basic meaning or intent of the sign even before you have a chance to read it.

ISTOPI

WRONG

WAY

L ENTER

Color of Road Signs RED means STOP. It may also indicate that some movement is not allowed. Examples are DO NOT ENTER and WRONG WAY.

RAILROAD ADVANCE CROSSING

YELLOW indicates a general warning. Slow down and be careful when you see a yellow sign. It may signal a railroad crossing ahead, a no-passing zone, or some other potentially dangerous situation. Likewise, a yellow solid line painted on the road means “Don’t Cross.”

LOW

SHOULDER

AHEAD

FLAGGER

ORANGE indicates road construction or maintenance. You’ll want to slow down when you see an orange sign, as part of the road may be closed off or torn up. And there may be workers and maintenance vehicles around, too.

SyRLL I uwfl

RWYTDW

GREEN is used to guide the driver. Green signs may indicate upcoming freeway exits or show the direction you should turn to reach a particular place.

ST0 PI1

V YIELD

HOS

BLUE signs with white letters show motorists’ services.

Shape of Road Signs The shape of the sign will tell you something, too. An OCTAGONAL (eight-sided) sign means STOP. It is always red with white letters.

A TRIANGLE, pointed downward, indicates YIELD. It assigns the right-of-way to traffic on certain approaches to an intersection.

CANOEING

BROWN signs point out recreation areas or points of historic or cultural interest.

END DIVIDED HIGHWAY

A DIAMOND-shaped sign is a warning of something ahead - for example, the end of a divided highway, a curve, steep hill, soft shoulder, or a narrow bridge.

A TRIANGULAR sign also is used on two-lane roads to indicate a NO PASSING ZONE. This sign will be on the left side of the roadway.

Your Driving and the Road

KEEP RIGHT

LEFT OR THROUGH

RIGHT TURN

ONLY

RECTANGULAR (square or oblong) signs show speed limits, parking regulations, give directions, and such information as distances to cities.

Symbols on Road Signs There are many international road signs in use today.

NO U TURN

NO

BICYCLES

NO

PARKING

The basic message of many of these signs is in pictures or graphic symbols. A picture within a circle with a diagonal line across it shows what not to do.

Traffic Lights We’re all familiar with traffic lights or stop lights. Often green arrows are being used in the lights for improved traffic control. On some multilane roads, green arrows light up, indicating that traffic in one or more lanes can move or make a turn. Green arrows don’t mean “go no matter what.’’ You’ll still need to proceed with caution, yielding the right of way to pedestrians and sometimes to other vehicles. Some traffic lights also use red arrows to signify that you must stop before turning on red.

REVERSIBLE LANE ON MULTI-LANE ROADWAY

NO PASSING ZONE

Many city roads and expressways, and 2ven bridges, use reversible-lane traffic control during rush hours. A red X light above a lane means no driving in that lane at that time. A green arrow means you may drive in that lane. Look for the signs posted to warn drivers what hours and days these systems are in effect.

Pavement Markings Pavement markings add to traffic signs and signals. They give information to drivers without taking attention from the roadway. A solid yellow line on your side of the road or lane means “don’t cross.”

Your Own Signals Drivers signal to others, too. It’s not only more polite, it’s safer to let other drivers know what you are doing. And in some places the law requires driver signals. Turn and lane change signals: Always signal when you plan to turn or change lanes. If necessary, you can use hand signals out the window: Left arm straight out for a left turn, down for slow or about-to-stop, and up for a right turn.

Your Driving and the Road

Slowing down: If time allows, tap the brake pedal once or twice in advance of slowing or stopping. This warns the driver behind you. Disabled: Your four-way flashers signal that your vehicle is disabled or is a hazard. See “Hazard Warning Flashers” in the Index.

Traffic Officer The traffic police officer is also a source of important information. The officer’s signals govern, no matter what the traffic lights or other signs say. The next section discusses some of the road conditions you may encounter.

136

Defensive Driving

The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your Chevrolet: Buckle up. (See “Safety Belts” in the Index.) Defensive driving really means “be ready for anything.“ On city streets, rural roads, or freeways, it means “always expect the unexpected.” Assume that pedestrians or other drivers are going to be careless and make mistakes. Anticipate what they might do. Be ready for their mistakes. Expect children to dash out from behind parked cars, often followed by other children. Expect occupants in parked cars to open doors into traffic. Watch for

movement in parked cars - someone may be about to open a door. Expect other drivers to run stop signs when you are on a through street. Be ready to brake if necessary as you go :hrough intersections. You may not have :o use the brake, but if you do, you will be -eady. If you’re driving through a shopping center parking lot where there are well-marked lanes, directional arrows, and designated parking areas, expect some drivers to ignore all these markings and dash straight toward one part of the lot.

?edestrians can be careless. Watch for hem. In general, you must give way to Jedestrians even if you know you have .he right of way. Xear-end collisions are about the most xeventable of accidents. Yet they are :ommon. Allow enough following listance. It’s the best defensive driving maneuver, in both city and rural driving. You never know when the vehicle in front 3f you is going to brake or turn suddenly.

Here’s a final bit of information about defensive driving. The most dangerous time for driving in the U.S. is very early on Sunday morning. In fact, GM Research studies show that the most and the least dangerous times for driving, every week, fall on the same day. That day is Sunday. The most dangerous time is Sunday from 3 a.m. to 4 a.m. The safest time is Sunday from 10 a.m. to 11 a.m. Driving the same distance on a Sunday at 3 a.m. isn’t just a little more dangerous than it is at 10 a.m. It‘s about 134 times more dangerous! That leads to the next section.

Drunken Driving

Death and injury associated with drinking and driving is a national tragedy. It’s the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol takes away three things that anyone needs to drive a vehicle: 0 Judgment 0 Muscular Coordination

Vision

Police records show that half of all motor vehicle-related deaths involve alcohol - a driver, a passenger or someone else, such as a pedestrian, had been drinking.

Your Driving and the Road

In most cases, these deaths are the result of someone who was drinking and driving. Over 25,000 motor vehicle-related deaths occur each year because of alcohol, and thousands of people are injured. Just how much alcohol is too much if a person plans to drive? Ideally, no one should drink alcohol and then drive. But if one does, then what’s “too much”? It can be a lot less than many might think. Although it depends on each person and situation, here is some general information on the problem.

... 138

The Blood Alcohol Content (BAC) of someone who is drinking depends upon four things:

How much alcohol is in the drink. The drinker’s body weight. The amount of food that is consumed before and during drinking. The length of time it has taken the drinker to consume the alcohol.

According to the American Medical Association, a 180-pound (82 kg) person who drinks three 12-ounce (355 ml) bottles of beer in an hour will end up with a BAC of about 0.06 percent. The person would reach the same BAC by drinking three 4-ounce (120 ml) glasses of wine or three mixed drinks if each had 1-1/2 ounces (45 ml) of a liquor like whiskey, gin or vodka. It’s the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s BAC would be close to 0.12 percent, A person who consumes food just before or during drinking will have a slightly lower BAC level.

DRlNKlNa THAT Wlll RESULT IN A BAC OF .O6% IN THE TIME SHOWN

I 3 HOURS

100 120 140 160 180 200 220 240

BODY WEIGHT IN POUNDS

The law in most U.S. states sets the legal limit at a BAC of 0.10 percent. In Canada the limit is 0.08 percent, and in some other countries it’s lower than that. The BAC will be over 0.10 percent after three to six drinks (in one hour). Of course, as we’ve seen, it depends on how much alcohol is in the drinks, and how quickly the person drinks them.

But it’s very important to keep in mind that the ability to drive is affected well below a BAC of 0.10 percent. Research shows that the driving skills of many people are impaired at a BAC approaching 0.05 percent, and that the effects are worse at night. All drivers are impaired at BAC levels above 0.05 percent. Statistics show that the chance of being in an accident increases sharply for drivers who have a BAC of 0.05 percent or above. A driver with a BAC level of 0.06 percent (three beers in one hour for a 180-pound or 82 kg person) has doubled his or her chance of having an accident.

At a BAC level of 0.10 percent, the chance of that driver having an accident is six times greater; at a level of 0.15 percent, the chances are twenty-five times greater! And, the body takes about an hour to rid itself of the alcohol in one drink. No amount of coffee or number of cold showers will speed that up. “I’ll be careful” isn’t the right answer. What if there’s an emergency, a need to take sudden action, as when a child darts into the street? A person with a higher BAC might not be able to react quickly enough to avoid the collision.

Your Driving and the Road

I U I I urrnKing ana men awing IS very dangerous. Your reflexes,

perceptions, and judgment will be affected by even a small amount of alcohol. You could have a serious - or even fatal - accident if you drive after drinking. Please don’t drink and drive or ride with a driver who has been drinking. Ride home in a cab; or if you’re with a group, designate a driver who will not drink.

Control of a Vehicle

You have three systems that make your vehicle go where you want it lo go. They are the brakes, the steering and the accelerator. All three systems have to do their work at the places where the tires meet the road. Sometimes, as when you’re driving on snow or ice, it’s easy to ask more of those control systems than the tires and road can provide. That means you can lose control of your vehicle.

There’s something else about drinking and driving that many people don’t know. Medical research shows that alcohol in a person’s system can make crash injuries worse. That’s especially true for brain, spinal cord and heart injuries. That means that if anyone who has been drinking - driver or passenger - is in a crash, the chance of being killed or permanently disabled is higher than if that person had not been drinking. And we’ve already seen that the chance of a crash itself is higher for drinking drivers.

... 140

Braking Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That’s perception time. Then you have to bring up your foot and do it. That’s reaction time. Average reaction time is about 3/4 of a second. But that’s only an average. It might be less with one driver and as long as two or three seconds or more with another. Age, physical condition, alertness, coordination, and eyesight all play a part. So do alcohol, drugs and frustration. But even in 3/4 of a second, a vehicle moving at 60 mph ( 100 km/h) travels 66 feet (20 m). That could be a lot of distance in an emergency, so keeping

:nough space between your vehicle and Dthers is important. And, of course, actual stopping distances vary greatly with the surface of the road :whether it’s pavement or gravel); the ;ondition of the road (wet, dry, icy); tire tread; and the condition of your brakes. Most drivers treat their brakes with care, Some, however, overwork the braking system with poor driving habits.

B Avoid needless heavy braking. Some

people drive in spurts - heavy acceleration followed by heavy braking - rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking. Don’t “ride” the brakes by letting your left foot rest lightly on the brake pedal while driving.

Your Driving and the Road

CAUTION: -

6 6 . nlulllg YVUl UlaKGS Cdn Cause them to overheat to the point

that they won’t work well. You might not be able to stop your vehicle in time to avoid an accident. If you “ride” your brakes, they will get so hot they will require a lot of pedal force to slow you down. Avoid “riding” the brakes.

Klamg-. me DraaKes wears tnern 01 lnuch faster. You would need costly brake replacement much sooner than normal, and it also reduces fuel economy.

If you keep pace with the traffic and allow realistic following distances, you will eliminate a lot of unnecessary braking. That means better braking and longer brake life.

If your engine ever stops while you’re driving, brake normally but don’t pump your brakes. If you do, the pedal may get harder to push down. If your engine stops, you will still have some power brake assist. But you will use it when you brake. Once the power assist is used up, it may take longer to stop and the brake pedal will be harder to push.

Anti-Lock Brakes (ABS) Your Chevrolet has an advanced electronic braking system that will help prevent skidding.

If there's a problem with the anti-lock brake system. the ABS INOP warning light will stay on or flash. See "Anti-Lock Brake System Warning Light" in the Index.

This light on the instrument panel will go on when you start your vehicle. When you start your vehicle, you may hear a momentary motor or clicking noise. And you may even notice that your brake pedal moves a little while this is going on. This is the ABS system testing itself. If you have your foot on the brake pedal, this check won't happen until the vehicle goes about 3 mph ( 5 km/h) or until you take your foot off the brake pedal.

1 4 3 . m -

Your Driving and the Road

Here's how anti-lock works. Let's say the road is wet. You're driving safely. Suddenly an animal jumps out in front of you. You slam on the brakes. Here's what happens with ABS. A computer senses that wheels are slowing down. The computer separately works the brakes at each front wheel and at the rear wheels. The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions.

You can steer around the obstacle while braking hard. As you brake, your conlputer keeps receiving updates on wheel speed and controls braking pressure accordingly. A Anti-lock doesn't change the I CAUTION;

time you need to get your foot up to the brake pedal. If you get too close to the vehicle in front of you, you won't have time to apply your brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even though you have anti-lock brakes.

I'o Use Anti-Lock: Don't pump the brakes. Just hold the brake pedal down and let anti-lock work for you. When the ABS is active, the LOW TRAC light comes on to indicate low traction conditions. Adjust your driving accordingly. The light will stay on for about four seconds after the ABS stops being active.

Disc Brake Wear Indicators Unless you have the four-wheel disc brake option, your Chevrolet has front disc brakes and rear drum brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake peda .1 firmly).

1 The brake wear warning sound - means that sooner or later your brakes won’t work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced.

LullllllullIg 1u UIIVt: W l l l l W U I I I - U U brake pads could result in r n c t l \ ~ brake repair.

Some driving conditions or climates may cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with your brakes. Rear Drum Brakes If you have rear drum brakes, they don’t have wear indicators, but if you ever hear a rear brake rubbing noise, have the rear brake linings inspected. Also, the rear brake drums should be removed and inspected each time the tires are removed for rotation or changing. When you have the front brakes replaced, have the rear brakes inspected, too. Brake linings should always be replaced as complete axle sets.

Your Driving and the Road

Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble.

If your brake pedal goes down farther than normal, your rear drum brakes may need adjustment. Adjust them by backing up and firmly applying the brakes a few times.

Brake Adjustment Every time you make a moderate brake stop, your disc brakes adjust for wear. If you rarely make a moderate or heavier stop, then your brakes might not adjust correctly. If you drive in that way, then - very carefully - make a few moderate brake stops about every 1000 miles (1 600 km), so your brakes will adjust properly.

Braking in Emergencies Use your anti-lock braking system when you need to. With anti-lock, you can steer and brake at the same time. In many emergencies, steering can help you more than even the very best braking.

Steering Power Steering If you lose power steering assist because the engine stops or the system fails to function, you can steer but it will take much more effort. Steering Tips Driving on Curves It’s important to take curves at a reasonable speed. A lot of the “driver lost control” accidents mentioned on the news happen on curves. Here’s why: Experienced driver or beginner, each of us is subject to the same laws of physics when driving on curves. The traction of

the tires against the road surface makes it possible for the vehicle to change its path when you turn the front wheels. If there’s no traction, inertia will keep the vehicle going in the same direction. If you’ve ever tried to steer a vehicle on wet ice, you’ll understand this. The traction you can get in a curve depends on the condition of your tires and the road surface, the angle at which the curve is banked, and your speed. While you’re in a curve, speed is the one factor you can control.

Suppose you’re steering through a sharp curve. Then you suddenly accelerate. Those two control systems - steering and acceleration - can overwhelm those places where the tires meet the road and make you lose control. What should you do if this ever happens? Let up on the accelerator pedal, steer the vehicle the way you want it to go, and slow down. Speed limit signs near curves warn that you should adjust your speed. Of course, the posted speeds are based on good weather and road conditions. Under less favorable conditions you’ll want to go slower.

If you need to reduce your speed as you approach a curve, do it before you enter the curve, while your front wheels are straight ahead. Try to adjust your speed so you can “drive” through the curve. Maintain a reasonable, steady speed. Wait to accelerate until you are out of the curve, and then accelerate gently into the straightaway. When you drive into a curve at night, it’s harder to see the road ahead of you because it bends away from the straight beams of your lights. This is one good reason to drive slower.

Your Driving and the Road

Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you. You can avoid these problems by braking - if you can stop in time. But sometimes you can’t; there isn’t room. That’s the time for evasive action - steering around the problem.

Your Chevrolet can perform very well in emergencies like these. First apply your brakes. It is better to remove as much speed as you can from a possible collision. Then steer around the problem, to the left or right depending on the space available. An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand.

But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object. You must then be prepared to steer back to your original lane and then brake to a controlled stop. Depending on your speed, this can be rather violent for an unprepared driver. This is one of the reasons driving experts recommend that you use your safety belts and keep both hands on the steering wheel. The fact that such emergency situations are always possible is a good reason to practice defensive driving at all times.

I Off-Road Recovery

You may find sometime that your right wheels have dropped off the edge of a road onto the shoulder (A) while you’re driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement. You can turn the steering wheel up to 1/4 turn (B) until the right front tire contacts the pavement edge. Then turn your steering wheel to go straight down the roadway.

If the shoulder appears to be about four inches (100 mm) or more below the pavement, this difference can cause problems. If there is not enough room to pull entirely onto the shoulder and stop, then follow the same procedures. But if the right front tire scrubs against the side of the pavement, do NOT steer more sharply. With too much steering angle, the vehicle may jump back onto the road with so much steering input that it crosses over into the oncoming traffic before you can bring it back under control. Instead, ease off again on the accelerator and steering input, straddle the pavement once more, then try again.

Passing The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again. A simple maneuver? Not necessarily! Passing another vehicle on a two-lane highway is a potentially dangerous move, since the passing vehicle occupies the same lane as oncoming traffic for several seconds. A miscalculation, an error in judgment, or a brief surrender to frustration or anger can suddenly put the passing driver face to face with the worst of all traffic accidents - the head-on collision.

149

Your Driving and the Road

So here are some tips for passing:

“Drive ahead.” Look down the road, to the sides, and to crossroads for situations that might affect your passing patterns. If you have any doubt whatsoever about making a successful pass, wait for a better time. Watch for traffic signs, pavement markings, and lines. If you can see a sign up ahead that might indicate a turn or an intersection, delay your pass. A broken center line usually indicates it’s all right to pass (providing the road ahead is clear).

..

= 150

Never cross a solid line on your side of the lane or a double solid line, even if the road seems empty of approaching traffic. If you suspect that the driver of the vehicle you want to pass isn’t aware of your presence, tap the horn a couple of times before passing. Do not get too close to the vehicle you want to pass while you’re awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you’re following a larger vehicle. Also, you won’t have adequate space if the vehicle ahead suddenly slows or stops. Keep back a reasonable distance.

0 When it looks like a chance to pass is coming up, start to accelerate but stay in the right lane and don’t get too close. Time your move so you will be increasing speed as the time comes to move into the other lane. If the way is clear to pass, you will have a “running start” that more than makes up for the distance you would lose by dropping back. And if something happens to cause you to cancel your pass, you need only slow down and drop back again and wait for another opportunity.

If other cars are lined up to pass a slow vehicle, wait your turn. But take care that someone isn’t trying to pass you as you pull out to pass the slow vehicle. Remember to glance over your shoulder and check the blind spot. Check your mirrors, glance over your shoulder, and start your left lane change signal before moving out of the right lane to pass. When you are far enough ahead of the passed vehicle to see its front in your inside mirror, activate your right lane change signal and move back into the right lane.

(Remember that your right outside mirror is convex. The vehicle you just passed may seem to be farther away from you than it really is.) Try not to pass more than one vehicle at a time on two-lane roads. Reconsider before passing the next vehicle. Don’t overtake a slowly moving vehicle too rapidly. Even though the brake lights are not flashing, it may be slowing down or starting to turn. If you’re being passed, make it easy for the following driver to get ahead of you. Perhaps you can ease a little to the right.

Loss of Control Let’s review what driving experts say about what happens when the three control systems (brakes, steering and acceleration) don’t have enough friction where the tires meet the road to do what the driver has asked. In any emergency, don’t give up. Keep trying to steer and constantly seek an escape route or area of less danger.

Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not “overdriving” those conditions. But skids are always possible.

Your Driving and the Road

The three types of skids correspond to your Chevrolet’s three control systems. In the braking skid your wheels aren’t rolling. In the steering or cornering skid, too much speed or steering in a curve causes tires to slip and lose cornering force. And in the acceleration skid too much throttle causes the driving wheels to spin. A cornering skid and an acceleration skid are best handled by easing your foot off the accelerator pedal. If your vehicle starts to slide (as when you turn a corner on a wet, snow- or ice-covered road), ease your foot off the accelerator pedal as soon as you feel the vehicle start to slide. Quickly steer the way you want the

vehicle to go. If you start steering quickly enough, your vehicle will straighten out. As it does, straighten the front wheels. Of course, traction is reduced when water, snow, ice, gravel, or other material is on the road. For safety, you’ll want to slow down and adjust your driving to these conditions. It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited.

While driving on a surface with reduced traction, try your best to avoid sudden steering, acceleration, or braking (including engine braking by shifting to a lower gear). Any sudden changes could cause the tires to slide. You may not realize the surface is slippery until your vehicle is skidding. Learn to recognize warning clues - such as enough water, ice or packed snow on the road to make a “mirrored surface” - and slow down when you have any doubt. Remember: Any anti-lock braking system (ABS) helps avoid only the braking skid. Steer the way you want to go.

Driving at Night

Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired - by alcohol or drugs, with night vision problems, or by fatigue. Here are some tips on night driving.

Drive defensively. Remember, this is the most dangerous time. Don’t drink and drive. (See “Drunken Driving’’ in the Index for more on this problem.) Adjust your inside rearview mirror to reduce the glare from headlights behind you.

Since you can’t see as well, you may need to slow down and keep more space between you and other vehicles. It’s hard to tell how fast the vehicle ahead is going just by looking at its taillights. Slow down, especially on higher speed roads. Your headlights can light up only so much road ahead. In remote areas, watch for animals. If you’re tired, pull off the road in a safe place and rest.

Night Vision No one can see as well at night as in the daytime. But as we get older these differences increase. A 50-year-old driver may require at least twice as much light to see the same thing at night as a 20-year-old. What you do in the daytime can also affect your night vision. For example, if you spend the day in bright sunshine you are wise to wear sunglasses. Your eyes will have less trouble adjusting to night.

Your Driving and the Road

But if you’re driving, don’t wear sunglasses at night. They may cut down on glare from headlights, but they also make a lot of things invisible that should remain visible - such as parked cars, obstacles, pedestrians, or even trains blocking railway crossings. You may want to put on your sunglasses after you have pulled into a brightly-lighted service or refreshment area. Eyes shielded from that glare may adjust more quickly to darkness back on the road. But be sure to remove your sunglasses before you leave the service area.-^-

You can be temporarily blinded by approaching lights. It can take a second or two, or even several seconds, for your eyes to readjust to the dark. When you are faced with severe glare (as from a driver who doesn’t lower the high beams, or a vehicle with misaimed headlights), slow down a little. Avoid staring directly into the approaching lights. If there is a line of opposing traffic, make occasional glances over the line of headlights to make certain that one of the vehicles isn’t starting to move into your lane. Once you are past the bright lights, give your eyes time to readjust before resuming speed.

High Beams [f the vehicle approaching you has its high beams on, signal by flicking yours to high and then back to low beam. This is :he usual signal to lower the headlight beams. If the other driver still doesn’t lower the beams, resist the temptation to put your high beams on. This only makes two half-blinded drivers. On a freeway, use your high beams only in remote areas where you won’t impair approaching drivers. In some places, like Zities, using high beams is illegal.

When you follow another vehicle on a freeway or highway, use low beams. True, most vehicles now have day/night mirrors that enable the driver to reduce glare. But outside mirrors are not of this type and high beams from behind can bother the driver ahead.

A Few More Night Driving Suggestions Keep your windshield and all the glass on your vehicle clean - inside and out. Glare at night is made much worse by dirt on the glass. Even the inside of the glass can build up a film caused by dust. Tobacco smoke also makes inside glass surfaces very filmy and can be a vision hazard if it’s left there.

Dirty glass makes lights dazzle and flash more than clean glass would, making the pupils of your eyes contract repeatedly. You might even want to keep a cloth and some glass cleaner in your vehicle if you need to clean your glass frequently. Remember that your headlights light up far less of a roadway when you are in a turn or curve. Keep your eyes moving; that way, it’s easier to pick out dimly lighted objects. Just as your headlights should be checked regularly for proper aim, so should your eyes be examined regularly. Some drivers suffer from night blindness - the inability to see in dim light - and aren’t even aware of it.

Driving in the Rain Rain and wet roads can mean driving trouble. On a wet road you can’t stop, accelerate or turn as well because your tire-to-road traction isn’t as good as on dry roads. And, if your tires don’t have much tread left, you’ll get even less traction. It’s always wise to go slower and be cautious if rain starts to fall while you are driving. The surface may get wet suddenly when your reflexes are tuned for driving on dry pavement.

Your Driving and the Road

Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you can’t, try to slow down before you hit them.

I I

Wet brakes can cause

- L accidents. They won’t work well in a quick stop and may cause pulling to one side. You could lose control of the vehicle. After driving through a large puddle of water or a car wash, apply your brake pedal lightly until your brakes work normally.

The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road, and even people walking. Road spray can often be worse for vision than rain, especially if it comes from a dirty road. So it is wise to keep your wiping equipment in good shape and keep your windshield washer tank filled. Replace your windshield wiper inserts when they show signs of streaking or missing areas on the windshield, or when strips of rubber start to separate from the inserts.

. I . 156

Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you’re going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road. You might not be aware of hydroplaning. You could drive along for some time without realizing your tires aren’t in constant contact with the road. You could find out the hard way: when you have to slow, turn, move out to pass - or if you get hit by a gust of wind. You could suddenly find yourself out of control.

Hydroplaning doesn’t happen often. But it can if your tires haven’t much tread or if the pressure in one or more is low. It can happen if a lot of water is standing on the road. If you can see reflections from trees, telephone poles, or other vehicles, and raindrops “dimple” the water’s surface, there could be hydroplaning. Hydroplaning usually happens at higher speeds. There just isn’t a hard and fast rule about hydroplaning. The best advice is to slow down when it is raining, and be careful.

Some Other Rainy Weather Tips

Turn on your headlights - not just your parking lights - to help make you more visible to others. Look for hard-to-see vehicles coming from behind. You may want to use your headlights even in daytime if it’s raining hard.

Your Driving and the Road

Besides slowing down, allow some extra following distance. And be especially careful when you pass another vehicle. Allow yourself more clear room ahead, and be prepared to have your view restricted by road spray. If the road spray is so heavy you are actually blinded, drop back. Don’t pass until conditions improve. Going more slowly is better than having an accident. Use your defogger if it helps. Have good tires with proper tread depth. (See “Tires” in the Index.)

. . 158

Driving in Fog, Mist and Haze

Fog can occur with high humidity or heavy frost. It can be so mild that you can see through it for several hundred feet (meters). Or it might be so thick that you can see only a few feet (meters) ahead. It may come suddenly to an otherwise clear road. And it can be a major hazard. When you drive into a fog patch, your visibility will be reduced quickly. The biggest dangers are striking the vehicle ahead or being struck by the one behind. Try to “read” the fog density down the road. If the vehicle ahead starts to become less clear or, at night, if the taillights are harder to see, the fog is probably thickening. Slow down to give traffic

behind you a chance to slow down. Everybody then has a better chance to avoid hitting the vehicle ahead. A patch of dense fog may extend only for a few feet (meters) or for miles (kilometers); you can’t really tell while you’re in it. You can only treat the situation with extreme care. One common fog condition - sometimes called mist or ground fog - can happen in weather that seems perfect, especially at night or in the early morning in valley and low, marshy areas. You can be suddenly enveloped in thick, wet haze that may even coat your windshield. You can often spot these fog patches or mist layers with your headlights. But

sometimes they can be waiting for you as you come over a hill or dip into a shallow valley. Start your windshield wipers and washer, to help clear accumulated road dirt. Slow down carefully.

Tips on Driving in Fog If you get caught in fog, turn your headlights on low beam, even in daytime. You’ll see - and be seen - better. Use your fog lights if your vehicle has them. Don’t use your high beams. The light will bounce off the water droplets that make up fog and reflect back at you.

Use your defogger. In high humidity, even a light buildup of moisture on the inside of the glass will cut down on your already limited visibility. Run your windshield wipers and washer occasionally. Moisture can build up on the outside glass, and what seems to be fog may actually be moisture on the outside of your windshield. Treat dense fog as an emergency. Try to find a place to pull off the road. Of course you want to respect another’s property, but you might need to put something between you and moving vehicles - space, trees, telephone poles, a private driveway, anything that removes you from other traffic.

[f visibility is near zero and you must stop but are unsure whether you are away from the road, turn your lights on, start your hazard warning flashers, and sound your horn at intervals or when you hear approaching traffic. Pass other vehicles in fog only if you can see far enough ahead to pass safely. Even then, be prepared to delay your pass if you suspect the fog is worse up ahead. If other vehicles try to pass you, make it easy for them.

Your Driving and the Road

City Driving

One of the biggest problems with city streets is the amount of traffic on them. You’ll want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: 0 Know the best way to get to where

you are going. Try not to drive around trying to pick out a familiar street or landmark. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip.

9 160

Try to use the freeways that rim and crisscross most large cities. You’ll save time and energy. (See the next section, “Freeway Driving.”) Treat a green light as a warning signal. A traffic light is there because the corner is busy enough to need it. When a light turns green, and just before you start to move, check both ways for vehicles that have not cleared the intersection or may be running the red light.

Obey all posted speed limits. But remember that they are for ideal road, weather and visibility conditions. You may need to drive below the posted limit in bad weather or when visibility is especially poor. Pull to the right (with care) and stop clear of intersections when you see or hear emergency vehicles.

Freeway Driving

Mile for mile. freeways (also called thruways, parkways, expressways, turnpikes, or superhighways) are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving. Too-Past or too-slow driving breaks a smooth traffic flow. Treat the left lane on a freeway as a passing lane.

Entering the Freeway At the entrance there is usually a ramp that leads to the freeway. If you have a clear view of the freeway as you drive along the entrance ramp, you should begin to check traffic. Try to determine where you expect to blend with the flow. If traffic is light. you may have no problem. But if it is heavy. find a gap as you move along the entering lane and time your approach. Try to merge into the gap at close to the prevailing speed. Switch on your turn signal, check your rearview mirrors as you move along, and glance over your shoulder as often as necessary. Try to blend smoothly with the traffic flow.

Driving on the Freeway Once you are on the freeway, adjust your speed to the posted limit or to the prevailing rate if it's slower. Stay in the right lane unless you want to pass. If you are on a two-lane freeway, treat the right lane as the slow lane and the left lane as the passing lane. If you are on a three-lane freeway, treat the right lane as the slower-speed through lane, the middle lane as the higher-speed through lane, and the left lane as the passing lane. Before changing lanes, check your rearview mirrors. Then use your turn signal.

Your Driving and the Road

Just before you leave the lane,’ glance quickly over your shoulder to make sure there isn’t another vehicle in your “blind” spot. If you are moving from an outside to a center lane on a freeway having more than two lanes, make sure another vehicle isn’t about to move into the same spot. Look at the vehicles two lanes over and watch for telltale signs: turn signals flashing, an increase in speed, or moving toward the edge of the lane. Be prepared to delay your move. Once you are moving on the freeway, make certain you allow a reasonable following distance. Expect to move slightly slower at night.

Leaving the Freeway When you want to leave the freeway, move to the proper lane well in advance. Dashing across lanes at the last minute is dangerous. If you miss your exit do not, under any circumstances, stop and back up. Drive on to the next exit. At each exit point is a deceleration lane. Ideally it should be long enough for you to enter it at freeway speed (after signaling, of course) and then do your braking before moving onto the exit ramp. Unfortunately, not all deceleration lanes are long enough - some are too short for all the braking. Decide when to start braking. If you must brake on the through lane, and if there is traffic close

162

behind you, you can allow a little extra time and flash your brake lights (in addition to your turn signal) as extra warning that you are about to slow down and exit. The exit ramp can be curved, sometimes quite sharply. The exit speed is usually posted. Reduce your speed according to your speedometer, not to your sense of motion. After driving for any distance at higher speeds, you may tend to think you are going slower than you actually are. For example, 40 mph (65 km/h) might seem like only 20 mph (30 km/h). Obviously, this could lead to serious trouble on a ramp designed for 20 mph (30 km/h)!

Driving a Long Distance

Although most long trips today are made on freeways, there are still many made on regular highways. Long-distance driving on freeways and regular highways is the same in some ways. The trip has to be planned and the vehicle prepared, you drive at higher-than-city speeds, and there are longer turns behind the wheel. You’ll enjoy your trip more if you and your vehicle are in good shape. Here are some :ips for a successful long trip.

Before Leaving on a Long Trip Make sure you’re ready. Try to be well rested. If you must start when you’re not fresh - such as after a day’s work - don’t plan to make too many miles that first part of the journey. Wear comfortable clothing and shoes you can easily drive in. Is your vehicle ready for a long trip? If you keep it serviced and maintained, it’s ready to go. If it needs service, have it done before starting out. Of course, you’ll find experienced and able service experts in Chevrolet dealerships all across North America. They’ll be ready and willing to help if you need it.

Here are some things you can check before a trip:

Windshield Washer Fluid: Is the reservoir full? Are all windows clean inside and outside? Wiper Blades: Are they in good shape? Fuel, Engine Oil, Other Fluids: Have you checked all levels? Lights: Are they all working? Are the lenses clean? Tires: They are vitally important to a safe, trouble-free trip. Is the tread good enough for long-distance driving? Are the tires all inflated to the recommended pressure?

163 -

Your Driving and the Road

0 Weather Forecasts: What’s the

weather outlook along your route? Should you delay your trip a short time to avoid a major storm system?

0 Maps: Do you have up-to-date

maps?

On the Road Unless you are the only driver, it is good to share the driving task with others. Limit turns behind the wheel to about 100 miles (160 km) or two hours at a sitting. Then, either change drivers or stop for some refreshment like coffee, tea or soft drinks and some limbering up. But do stop and move around. Eat lightly along the way. Heavier meals tend to make some people sleepy.

164

m .

On two-lane highways or undivided multilane highways that do not have controlled access, you’ll want to watch for some situations not usually found on freeways. Examples are: stop signs and signals, shopping centers with direct access to the highway, no passing zones and school zones, vehicles turning left and right off the road, pedestrians, cyclists, parked vehicles, and even animals.

Highway Hypnosis Is there actually such a condition as “highway hypnosis”? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy. Don’t let it happen to you! If it does, your vehicle can leave the road in less than a second, and you could crash and be injured.

What can you do about highway hypnosis'? First, be aware that it can happen. Then here are some tips:

Make sure your vehicle is well ventilated, with a comfortably cool interior. Keep your eyes moving. Scan the road ahead and to the sides. Check your rearview mirrors frequently and your instruments from time to time. This can help you avoid a fixed stare.

Wear good sunglasses in bright light. Glare can cause drowsiness. But don't wear sunglasses at night. They will drastically reduce your overall vision at the very time you need all the seeing power you have. If you get sleepy, pull off the road into a rest, service, or parking area and take a nap, get some exercise, or both. For safety, treat drowsiness on the highway as an emergency.

As in any driving situation. keep pace with traffic and allow adequate following distances.

Hill and Mountain Roads

Driving on steep hills or mountains is different from driving in flat or rolling