and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
6. If your vehicle will be towing a trailer, the load
from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
Your vehicle is not designed nor intended to tow a trailer.
Example 1
Item
Description
Vehicle Capacity Weight or Maximum Load for Example 1 = Subtract Occupant Weight 150 lbs (68 kg) × 2 = Available Occupant and Cargo Weight =
Total
1,000 lbs (453 kg)
300 lbs (136 kg)
700 lbs (317 kg)
4-21
Example 2
Example 3
Item
Description
Vehicle Capacity Weight or Maximum Load for Example 2 = Subtract Occupant Weight 150 lbs (68 kg) × 5 = Available Cargo Weight =
Total
1,000 lbs (453 kg)
750 lbs (340 kg)
250 lbs (113 kg)
4-22
Item
Description
Vehicle Capacity Weight or Maximum Load for Example 3 = Subtract Occupant Weight 200 lbs (91kg) × 5 = Available Cargo Weight =
Total
1,000 lbs (453 kg)
1,000 lbs (453 kg)
0 lbs (0 kg)
Refer to your vehicle’s Tire and Loading Information label for specific information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s maximum load weight.
Certification Label
A vehicle specific Certification label is attached to the center pillar (B-pillar), below the driver’s door latch. This label tells you the gross weight capacity of your vehicle, called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel and cargo. Never exceed the GVWR for your vehicle, or the Gross Axle Weight Rating (GAWR) for either the front or rear axle. And, if you do have a heavy load, you should spread it out. See “Steps for Determining Correct Load Limit” earlier in this section.
Label Example - United States
{ CAUTION:
Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on the vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of the vehicle.
Notice: Overloading your vehicle may cause damage. Repairs would not be covered by your warranty. Do not overload your vehicle.
4-23
Label Example - Canada
If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going.
{ CAUTION:
Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash.
(cid:129) Put things in the cargo area of your
vehicle. Try to spread the weight evenly. (cid:129) Never stack heavier things, like suitcases,
inside the vehicle so that some of them are above the tops of the seats.
(cid:129) Do not leave an unsecured child restraint
in your vehicle.
(cid:129) When you carry something inside the vehicle, secure it whenever you can.
(cid:129) Do not leave a seat folded down unless
you need to.
Towing
Towing Your Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 7-7. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motorhome, see “Recreational Vehicle Towing” following.
Recreational Vehicle Towing Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motorhome. The two most common types of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground. Dolly towing is towing the vehicle with two wheels on the ground and two wheels up on a device known as a dolly.
4-24
Here are some important things to consider before recreational vehicle towing: (cid:129) What is the towing capacity of the towing vehicle?
Be sure to read the tow vehicle manufacturer’s recommendations.
(cid:129) What is the distance that will be travelled? Some
vehicles have restrictions on how far and how long they can tow. Is the proper towing equipment going to be used? See your dealer/retailer or trailering professional for additional advice and equipment recommendations. Is the vehicle ready to be towed? Just as preparing the vehicle for a long trip, make sure the vehicle is prepared to be towed. See Before Leaving on a Long Trip on page 4-11.
Dinghy Towing
If the vehicle is towed with all four wheels
Notice: on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty. Do not tow the vehicle with all four wheels on the ground. The vehicle was not designed to be towed with all four wheels on the ground. If the vehicle must be towed, a dolly should be used. See “Dolly Towing” that follows for more information.
4-25
(cid:129) (cid:129) Dolly Towing From the Front
3. Put an automatic transmission in P (Park) or a
manual transmission in N (Neutral).
4. Set the parking brake and remove the key. 5. For an automatic transmission, insert the key into the shift-lock release slot and shift to N (Neutral). See Shifting Out of Park on page 2-30.
6. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing.
7. Release the parking brake.
The vehicle can be towed from the front using a dolly. To tow the vehicle using a dolly, follow these steps: 1. Attach the dolly to the tow vehicle following the
dolly manufacturer’s instructions.
2. Drive the front wheels onto the dolly.
4-26
Dolly Towing From the Rear
Towing a Trailer The vehicle is neither designed nor intended to tow a trailer.
Notice: Towing the vehicle from the rear with the front wheels on the ground could cause transmission damage. Do not tow the vehicle from the rear with the front wheels on the ground.
4-27
✍ NOTES
4-28
Section 5
Service and Appearance Care
Service ............................................................5-3
Accessories and Modifications ..........................5-3
California Proposition 65 Warning .....................5-4
California Perchlorate Materials Requirements .....5-4
Doing Your Own Service Work .........................5-4
Adding Equipment to the Outside of
the Vehicle .................................................5-5
Fuel ................................................................5-5
Gasoline Octane ............................................5-5
Gasoline Specifications ....................................5-5
California Fuel
...............................................5-6
Additives .......................................................5-6
Fuels in Foreign Countries ...............................5-7
Filling the Tank ..............................................5-8
Filling a Portable Fuel Container .....................5-11
Checking Things Under the Hood ....................5-11
Hood Release ..............................................5-12
Engine Compartment Overview .......................5-14
Engine Oil ...................................................5-16
Engine Oil Life System ..................................5-18
Engine Air Cleaner/Filter ................................5-19
Automatic Transmission Fluid .........................5-21
Manual Transmission Fluid .............................5-23
Hydraulic Clutch ...........................................5-23
Cooling System ............................................5-24
Engine Coolant .............................................5-25
Engine Overheating .......................................5-30
Power Steering Fluid .....................................5-32
Windshield Washer Fluid ................................5-33
Brakes ........................................................5-34
Battery ........................................................5-37
Jump Starting ...............................................5-38
Headlamp Aiming ...........................................5-43
Bulb Replacement ..........................................5-43
Halogen Bulbs ..............................................5-43
Headlamps ..................................................5-44
Front Turn Signal, Sidemarker and
Parking Lamps ..........................................5-45
Center High-Mounted Stoplamp (CHMSL)
(Hatchback) ..............................................5-47
Center High-Mounted Stoplamp (CHMSL)
(Sedan) ...................................................5-47
Taillamps, Turn Signal, Sidemarker,
Stoplamps and Back-up Lamps ...................5-48
License Plate Lamp ......................................5-49
Replacement Bulbs .......................................5-49
Windshield Wiper Blade Replacement ..............5-50
Tires ..............................................................5-51
Tire Sidewall Labeling ...................................5-52
Tire Terminology and Definitions .....................5-54
Inflation - Tire Pressure .................................5-57
Tire Pressure Monitor System .........................5-59
5-1
Section 5
Service and Appearance Care
Tire Pressure Monitor Operation .....................5-60
Tire Inspection and Rotation ...........................5-62
When It Is Time for New Tires .......................5-63
Buying New Tires .........................................5-64
Different Size Tires and Wheels ......................5-65
Uniform Tire Quality Grading ..........................5-66
Wheel Alignment and Tire Balance ..................5-67
Wheel Replacement ......................................5-67
Tire Chains ..................................................5-68
If a Tire Goes Flat ........................................5-69
Changing a Flat Tire .....................................5-70
Removing the Spare Tire and Tools ................5-71
Removing the Flat Tire and Installing the
Spare Tire ................................................5-73
Storing a Flat or Spare Tire and Tools ............5-78
Compact Spare Tire ......................................5-78
Appearance Care ............................................5-79
Interior Cleaning ...........................................5-79
Fabric/Carpet ...............................................5-80
Leather .......................................................5-81
Instrument Panel, Vinyl, and Other Plastic
Surfaces ..................................................5-81
Care of Safety Belts ......................................5-82
Weatherstrips ...............................................5-82
Washing Your Vehicle ...................................5-82
Cleaning Exterior Lamps/Lenses .....................5-83
Finish Care ..................................................5-83
Windshield and Wiper Blades .........................5-84
Aluminum Wheels .........................................5-84
Tires ...........................................................5-85
Sheet Metal Damage .....................................5-85
Finish Damage .............................................5-85
Underbody Maintenance ................................5-85
Chemical Paint Spotting .................................5-85
Vehicle Identification ......................................5-86
Vehicle Identification Number (VIN) .................5-86
Service Parts Identification Label .....................5-86
Electrical System ............................................5-86
Add-On Electrical Equipment ..........................5-86
Headlamp Wiring ..........................................5-87
Windshield Wiper Fuses ................................5-87
Power Windows and Other Power Options .......5-87
Fuses and Circuit Breakers ............................5-87
Instrument Panel Fuse Block ..........................5-88
Engine Compartment Fuse Block ....................5-89
Capacities and Specifications ..........................5-93
5-2
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks:
Accessories and Modifications When non-dealer/non-retailer accessories are added to the vehicle, they can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes, traction control, and stability control. Some of these accessories could even cause malfunction or damage not covered by the vehicle warranty. Damage to vehicle components resulting from the installation or use of non-GM certified parts, including control module modifications, are not covered under the terms of the vehicle warranty and may affect remaining warranty coverage for affected parts. GM Accessories are designed to complement and function with other systems on the vehicle. Your GM dealer/retailer can accessorize the vehicle using genuine GM Accessories. When you go to your GM dealer/retailer and ask for GM Accessories, you will know that GM-trained and supported service technicians will perform the work using genuine GM Accessories. Also, see Adding Equipment to Your Airbag-Equipped Vehicle on page 1-74.
5-3
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many fluids, and some component wear by-products contain and/or emit these chemicals.
California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, seat belt pretensioners, and lithium batteries contained in remote keyless transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/perchlorate.
5-4
Doing Your Own Service Work
{ CAUTION:
You can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it.
(cid:129) Be sure you have sufficient knowledge,
experience, the proper replacement parts, and tools before attempting any vehicle maintenance task.
(cid:129) Be sure to use the proper nuts, bolts, and
other fasteners. English and metric fasteners can be easily confused. If the wrong fasteners are used, parts can later break or fall off. You could be hurt.
If doing some of your own service work, use the proper service manual. It tells you much more about how to service the vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-17.
This vehicle has an airbag system. Before attempting to do your own service work, see Servicing Your Airbag-Equipped Vehicle on page 1-73. Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 6-17.
Adding Equipment to the Outside of the Vehicle Things added to the outside of the vehicle can affect the airflow around it. This can cause wind noise and can affect fuel economy and windshield washer performance. Check with your dealer/retailer before adding equipment to the outside of the vehicle. Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. To help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline.
Gasoline Octane Use regular unleaded gasoline with a posted octane rating of 87 or higher. If the octane rating is less than 87, you might notice an audible knocking noise when you drive, commonly referred to as spark knock. If this occurs, use a gasoline rated at 87 octane or higher as soon as possible. If you are using gasoline rated at 87 octane or higher and you hear heavy knocking, the engine needs service.
Gasoline Specifications At a minimum, gasoline should meet ASTM specification D 4814 in the United States or CAN/CGSB-3.5 or 3.511 in Canada. Some gasolines contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). We recommend against the use of gasolines containing MMT. See Additives on page 5-6 for additional information.
5-5
California Fuel If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, the vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance might be affected. The malfunction indicator lamp could turn on and the vehicle might fail a smog-check test. See Malfunction Indicator Lamp on page 3-32. If this occurs, return to your authorized dealer/retailer for diagnosis. If it is determined that the condition is caused by the type of fuel used, repairs might not be covered by the vehicle warranty.
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S. Environmental Protection Agency regulations. To help keep fuel injectors and intake valves clean, or if the vehicle experiences problems due to dirty injectors or valves, look for gasoline that is advertised as TOP TIER Detergent Gasoline. For customers who do not use TOP TIER Detergent Gasoline regularly, one bottle of GM Fuel System Treatment PLUS, added to the fuel tank at every engine oil change, can help clean deposits from fuel injectors and intake valves. GM Fuel System Treatment PLUS is the only gasoline additive recommended by General Motors.
5-6
Also, your dealer/retailer has additives that will help correct and prevent most deposit-related problems. Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the specifications described earlier. However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels. Notice: This vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in the fuel system and also damage plastic and rubber parts. That damage would not be covered under the vehicle warranty.
Some gasolines that are not reformulated for low emissions can contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT); ask the attendant where you buy gasoline whether the fuel contains MMT. We recommend against the use of such gasolines. Fuels containing MMT can reduce the life of spark plugs and the performance of the emission control system could be affected. The malfunction indicator lamp might turn on. If this occurs, return to your dealer/retailer for service.
Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel might be hard to find. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty. To check the fuel availability, ask an auto club, or contact a major oil company that does business in the country where you will be driving.
5-7
To open the fuel filler door, pull up on the release lever with this symbol on it. It is located on the floor on the outboard side of the driver seat.
Filling the Tank
{ CAUTION:
Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling. Do not smoke if you are near fuel or refueling the vehicle. Do not use cellular phones. Keep sparks, flames, and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling the vehicle. This is against the law in some places. Do not re-enter the vehicle while pumping fuel. Keep children away from the fuel pump; never let children pump fuel.
5-8
Hatchback shown. Sedan similar
The tethered fuel cap is located behind a hinged fuel door on the passenger side of the vehicle. To remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right.
{ CAUTION:
Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop. Then unscrew the cap all the way.
Be careful not to spill fuel. Do not top off or overfill the tank and wait a few seconds after you have finished pumping before removing the nozzle. Clean fuel from painted surfaces as soon as possible. See Washing Your Vehicle on page 5-82.
5-9
When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 3-32.
If a new fuel cap is needed, be sure to get
Notice: the right type. Your dealer/retailer can get one for you. The wrong type might not fit properly. This can cause the malfunction indicator lamp to light and can damage the fuel tank and emissions system. See Malfunction Indicator Lamp on page 3-32.
{ CAUTION:
If a fire starts while you are refueling, do not remove the nozzle. Shut off the flow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately.
5-10
Filling a Portable Fuel Container
{ CAUTION:
Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others:
(cid:129) Dispense fuel only into approved containers. (cid:129) Do not fill a container while it is inside a
vehicle, in a vehicle’s trunk, pickup bed, or on any surface other than the ground.
(cid:129) Bring the fill nozzle in contact with the inside of the fill opening before operating the nozzle. Contact should be maintained until the filling is complete.
(cid:129) Do not smoke while pumping fuel. (cid:129) Do not use a cellular phone while
pumping fuel.
Checking Things Under the Hood
{ CAUTION:
An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan.
{ CAUTION:
Things that burn can get on hot engine parts and start a fire. These include liquids like fuel, oil, coolant, brake fluid, windshield washer and other fluids, and plastic or rubber. You or others could be burned. Be careful not to drop or spill things that will burn onto a hot engine.
5-11
Hood Release To open the hood:
1. Pull the hood release
handle inside the vehicle. It is located on the lower left side of the instrument panel.
5-12
2. Then go to the front of the vehicle and lift up on the
secondary hood release lever, located under the front center of the hood.
3. Lift the hood and release the hood prop from its
retainer located on the underside of the hood.
4. Securely place the hood prop into the slot on the
inner fender.
Before closing the hood, be sure all the filler caps are on properly. Then lift the hood to relieve pressure on the hood prop. Remove the hood prop from the slot in the inner fender and return the prop to its retainer. Lower the hood 12 inches (30 cm) above the vehicle and release it so it fully latches. Check to make sure the hood is closed and repeat the process if necessary.
5-13
Engine Compartment Overview
Automatic Transmission shown, Manual Transmission similar
5-14
A. Engine Air Cleaner/Filter on page 5-19. B. Engine Oil Fill Cap. See “When to Add Engine Oil”
under Engine Oil on page 5-16.
C. Brake/Clutch Fluid Reservoir. See “Brake Fluid”
under Brakes on page 5-34 and Hydraulic Clutch on page 5-23.
D. Engine Coolant Surge Tank. See Cooling System on
page 5-24.
E. Engine Compartment Fuse Block on page 5-89. F. Battery on page 5-37.
G. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under Windshield Washer Fluid on page 5-33.
H. Engine Oil Dipstick. See “Checking Engine Oil”
under Engine Oil on page 5-16.
I. Automatic Transmission Dipstick. See Automatic
Transmission Fluid on page 5-21.
J. Power Steering Fluid Reservoir. See Power Steering
Fluid on page 5-32.
5-15
Engine Oil
When to Add Engine Oil
If the engine oil pressure light comes on, check the engine oil level right away.
The oil pressure light is on the instrument panel cluster. See Oil Pressure Light on page 3-34. Check the engine oil level regularly; this is an added reminder. Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 5-14 for the location of the engine oil dipstick. 1. Turn off the engine and give the oil several minutes to drain back into the oil pan. If this is not done, the oil dipstick might not show the actual level.
2. Pull the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down and check the level.
5-16
If the oil is below the MIN (minimum) mark on the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 5-93. Notice: Do not add too much oil. If the engine has so much oil that the oil level gets above the upper mark that shows the proper operating range, the engine could be damaged. See Engine Compartment Overview on page 5-14 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when through.
What Kind of Engine Oil to Use Look for three things:
(cid:129) GM6094M
Use only an oil that meets GM Standard GM6094M.
(cid:129) SAE 5W-30
SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50.
(cid:129) American Petroleum Institute (API) starburst symbol
Oils meeting these requirements should have the starburst symbol on the container. This symbol indicates that the oil has been certified by the American Petroleum Institute (API).
Notice: Use only engine oil identified as meeting
GM Standard GM6094M and showing the American
Petroleum Institute Certified For Gasoline Engines
starburst symbol. Failure to use the recommended
oil can result in engine damage not covered by
the vehicle warranty.
Cold Temperature Operation
If in an area of extreme cold, where the temperature
falls below −20°F (−29°C), use either an SAE 5W-30
synthetic oil or an SAE 0W-30 engine oil. Both provide
easier cold starting for the engine at extremely low
temperatures. Always use an oil that meets the required
specification, GM6094M. See “What Kind of Engine
Oil to Use” for more information.
5-17
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty.
Engine Oil Life System When to Change Engine Oil This vehicle has the Engine Oil Life System, a computer system that indicates when to change the engine oil and filter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change is indicated can vary considerably. For the oil life system to work properly, the system must be reset every time the oil is changed. When the system has calculated that oil life has been diminished, it indicates that an oil change is necessary. A change engine oil light displays. Change the oil as soon as possible within the next 600 miles (1 000 km).
It is possible that, if driving under the best conditions, the oil life system might not indicate that an oil change is necessary for over a year. However, the engine oil and filter must be changed at least once a year and at this time the system must be reset. Your dealer/retailer has trained service people who will perform this work using genuine parts and reset the system. It is also important to check the oil regularly and keep it at the proper level. If the system is ever reset accidentally, the oil must be changed at 3,000 miles (5 000 km) since the last oil change. Remember to reset the oil life system whenever the oil is changed. How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a change engine oil light being turned on, reset the system. After changing the engine oil, the system must be reset: 1. With the engine off, turn the ignition key to ON/RUN. 2. Fully press and release the accelerator pedal slowly
three times within five seconds.
3. Turn the key to LOCK/OFF, then start the vehicle.
5-18
If the change engine oil light comes back on when the vehicle is started, the engine oil life system has not reset. Repeat the reset procedure. What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly dispose of clothing or rags containing used engine oil. See the manufacturer’s warnings about the use and disposal of oil products. Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the filter before disposal. Never dispose of oil by putting it in the trash, pouring it on the ground, into sewers, or into streams or bodies of water. Recycle it by taking it to a place that collects used oil.
Engine Air Cleaner/Filter The engine air cleaner/filter is located in the engine compartment on the passenger side of the vehicle. See Engine Compartment Overview on page 5-14 for more information on location. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/filter at the Maintenance II intervals and replace it at the first oil change after each 50,000 mile (80 000 km) interval. See Scheduled Maintenance on page 6-4 for more information. If you are driving in dusty/dirty conditions, inspect the filter at each engine oil change. How to Inspect the Engine Air Cleaner/Filter To inspect the engine air cleaner/filter, remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt. If the filter remains caked with dirt, a new filter is required.
5-19
{ CAUTION:
Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. If it is not there and the engine backfires, you could be burned. Do not drive with it off, and be careful working on the engine with the air cleaner/filter off.
If the air cleaner/filter is off, a backfire can
Notice: cause a damaging engine fire. And, dirt can easily get into the engine, which will damage it. Always have the air cleaner/filter in place when you are driving.
To inspect or replace the air cleaner/filter:
1. Remove the screws and lift off the cover. 2. Inspect or replace the engine air cleaner/filter. 3. Put the cover back on tightly and tighten the screws. See Additional Required Services on page 6-6 for replacement intervals.
5-20
Automatic Transmission Fluid When to Check Automatic Transmission Fluid Check the automatic transmission fluid level at least twice a year. Add fluid if needed. See Scheduled Maintenance on page 6-4. How to Check Automatic Transmission Fluid Because this operation can be a little difficult, you may choose to have this done at the dealer/retailer service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. Notice: Too much or too little fluid can damage your transmission. Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts, starting a fire. Too little fluid could cause the transmission to overheat. Be sure to get an accurate reading if you check your transmission fluid.
Wait at least 30 minutes before checking the transmission fluid level if you have been driving: (cid:129) When outside temperatures are above 90°F (32°C). (cid:129) At high speed for quite a while.
In heavy traffic — especially in hot weather.
To get the right reading, the fluid should be at normal operating temperature, which is 158°F to 176°F (70°C to 80°C). Get the vehicle warmed up by driving about 15 miles (24 km) when outside temperatures are above 50°F (10°C). If it is colder than 50°F (10°C), you may have to drive longer. Checking the Fluid Level Prepare the vehicle as follows: 1. Park the vehicle on a level place. Keep the engine
running.
2. With the parking brake applied, place the shift lever
in P (Park).
3. With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, position the shift lever in P (Park).
4. Let the engine run at idle for three to five minutes.
5-21
(cid:129) Then, without shutting off the engine, follow these steps: 1. Locate the automatic transmission dipstick which
is located toward the front of the engine
compartment, near the power steering fluid
reservoir.
See Engine Compartment Overview on page 5-14
for more information on location.
2. Pull out the dipstick and wipe it with a clean rag or
paper towel.
3. Push the dipstick back in all the way, wait three
seconds, and then pull it back out again.
4. Check both sides of the dipstick. The fluid should be between MIN (A) and MAX (B) mark of the hot area of the dipstick.
5. If the fluid level is in the acceptable range, push the
dipstick back in all the way.
5-22
How to Add Automatic Transmission Fluid Refer to the Maintenance Schedule to determine what kind of transmission fluid to use. See Recommended Fluids and Lubricants on page 6-13. If the fluid level is low, add only enough of the proper fluid to bring the level into the area between the two dimples in the hot range on the dipstick. 1. Pull out the dipstick. 2. Using a long-neck funnel, add enough fluid at the
dipstick hole to bring it to the proper level. It does not take much fluid, generally less than one pint (0.5 L). Do not overfill.
Notice: Use of the incorrect automatic transmission fluid may damage the vehicle, and the damages may not be covered by the vehicle’s warranty. Always use the automatic transmission fluid listed in Recommended Fluids and Lubricants on page 6-13. 3. After adding fluid, recheck the fluid level as described under “How to Check Automatic Transmission Fluid” earlier in this section.
4. When the correct fluid level is obtained, push the
dipstick back in all the way.
Manual Transmission Fluid It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to the dealer/retailer service department and have it repaired as soon as possible. See Recommended Fluids and Lubricants on page 6-13 for the proper fluid to use.
Hydraulic Clutch There is one reservoir for both the brake and the hydraulic clutch fluid. See Brakes on page 5-34 for more information. The hydraulic clutch linkage in the vehicle is self-adjusting. The master cylinder reservoir is filled with hydraulic fluid. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. When to Check and What to Use Refer to the Maintenance Schedule to determine how often to check the fluid level in the master cylinder reservoir and for the proper fluid. See Owner Checks and Services on page 6-9 and Recommended Fluids and Lubricants on page 6-13.
How to Check and Add Fluid The reservoir is located near the back of the engine compartment on the driver side of the vehicle. See Engine Compartment Overview on page 5-14 for more information on location.
To check the fluid level, look on the side of the reservoir. If the fluid reaches the MAX (A) mark on the reservoir, the fluid level is correct. If the fluid does not reach the MIN (B) mark on the reservoir, then fluid needs to be added.
5-23
Cooling System The cooling system allows the engine to maintain the correct working temperature.
{ CAUTION:
An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.
A. Electric Engine Cooling Fan B. Coolant Surge Tank with Pressure Cap
5-24
{ CAUTION:
Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle.
Notice: Using coolant other than DEX-COOL® can cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant may require changing sooner, at the first maintenance service after each 30,000 miles (50 000 km) or 24 months, whichever occurs first. Any repairs would not be covered by the vehicle warranty. Always use DEX-COOL® (silicate-free) coolant in the vehicle.
Engine Coolant The cooling system in the vehicle is filled with DEX-COOL® engine coolant. This coolant is designed to remain in the vehicle for five years or 150,000 miles (240 000 km), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low. If there is a problem with engine overheating, see Engine Overheating on page 5-30.
5-25
What to Use
{ CAUTION:
Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and DEX-COOL® coolant.
Use a 50/50 mixture of clean, drinkable water and DEX-COOL® coolant. If using this mixture, nothing else needs to be added. This mixture: (cid:129) Gives freezing protection down to −34°F (−37°C),
outside temperature.
(cid:129) Gives boiling protection up to 265°F (129°C), engine
temperature.
(cid:129) Protects against rust and corrosion.
5-26
If an improper coolant mixture is used,
(cid:129) Will not damage aluminum parts. (cid:129) Helps keep the proper engine temperature. Notice: the engine could overheat and be badly damaged. The repair cost would not be covered by the vehicle warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core, and other parts. Notice: If extra inhibitors and/or additives are used in the vehicle’s cooling system, the vehicle could be damaged. Use only the proper mixture of the engine coolant listed in this manual for the cooling system. See Recommended Fluids and Lubricants on page 6-13 for more information. Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant surge tank. If the coolant inside the coolant surge tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not between the Minimum and Maximum marks, add a 50/50 mixture of clean, drinkable water and DEX-COOL® coolant at the coolant surge tank, but be sure the cooling system is cool before this is done. See Engine Coolant on page 5-25 for more information.
The engine coolant surge tank is located in the rear of the engine compartment on the driver side of the vehicle. See Engine Compartment Overview on page 5-14 for more information on location.
{ CAUTION:
Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. Never turn the surge tank pressure cap — even a little — when the engine and radiator are hot.
When the engine is cold, the coolant level should be between the Maximum (A) and Minimum (B) marks on the coolant surge tank. The level rises at engine operation temperature and drops again when the engine cools down. The coolant should be between the Maximum (A) and Minimum (B) marks, when the engine is cold. If it is not, there could be a leak in the cooling system.
5-27
How to Add Coolant to the Coolant Surge Tank
{ CAUTION:
{ CAUTION:
You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine.
Notice: This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged.
{ CAUTION:
An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.
Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the surge tank pressure cap — even a little — they can come out at high speed. Never turn the cap when the cooling system, including the surge tank pressure cap, is hot. Wait for the cooling system and surge tank pressure cap to cool if you ever have to turn the pressure cap.
If no coolant is visible in the surge tank, add coolant as follows: 1. Remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise about two or two and one-half turns. If you hear a hiss, wait for that to stop. This will allow any pressure still left to be vented out the discharge hose.
5-28
2. Then keep turning the pressure cap slowly and
remove it.
3. Fill the coolant surge tank with the proper mixture to the Maximum mark on the coolant surge tank. Wait about five minutes, then check to see if the level is below the mark. If the level is below the Maximum mark, add additional coolant to bring the level up to the mark. Repeat this procedure until the level remains constant at the Maximum mark for at least five minutes.
5-29
4. With the coolant surge tank pressure cap off, start
the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. By this time, the coolant level inside the coolant surge tank may be lower. If the level is lower than the Maximum mark, add more of the proper mixture to the coolant surge tank until the level reaches the mark.
5. Replace the pressure cap. Be sure the pressure
cap is hand-tight and fully seated.
If the pressure cap is not tightly installed,
Notice: coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured.
Engine Overheating The vehicle has an indicator to warn of the engine overheating. There is a coolant temperature gage on the instrument panel cluster. See Engine Coolant Temperature Gage on page 3-31. You may decide not to lift the hood when this warning appears, but instead get service help right away. See Roadside Assistance Program on page 7-7. If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fan is running. If the engine is overheating, the fan should be running. If it is not, do not continue to run the engine and have the vehicle serviced. Notice: Engine damage from running the engine without coolant is not covered by the warranty. Notice: driven with no coolant, your vehicle can be badly damaged. The costly repairs would not be covered by the vehicle warranty.
If the engine catches fire because of being
5-30
If Steam Is Coming From The Engine Compartment
{ CAUTION:
Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood. If you keep driving when your engine is overheated, the liquids in it can catch fire. You or others could be badly burned. Stop your engine if it overheats, and get out of the vehicle until the engine is cool.
If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: (cid:129) Climbs a long hill on a hot day. (cid:129) Stops after high-speed driving. Idles for long periods in traffic.
If the overheat warning is displayed with no sign of steam: 1. Turn the air conditioning off. 2. Turn the heater on to the highest temperature and
to the highest fan speed. Open the windows as necessary.
3. If in a traffic jam, let the engine idle in N (Neutral)
while stopped. If it is safe to do so, pull off the road, shift to P (Park) or N (Neutral) and let the engine idle.
If the temperature overheat gage is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you. If the warning does not come back on, continue to drive normally.
5-31
(cid:129) If the warning continues, pull over, stop, and park the vehicle right away. If there is no sign of steam, idle the engine for three minutes while parked. If the warning is still displayed, turn off the engine until it cools down.
Power Steering Fluid When to Check Power Steering Fluid The power steering fluid reservoir is located toward the front of the engine compartment on the driver’s side of the vehicle. See Engine Compartment Overview on page 5-14 for reservoir location. It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired.
5-32
How to Check Power Steering Fluid Turn the key off and let the engine compartment cool down.
The level should be between the MIN (B) and MAX (A) marks on the reservoir. If the level drops below the MIN (B) mark, add power steering fluid. Do not overfill the reservoir and remember to replace the cap tightly when you are finished and clean up any spilled fluid.
What to Use To determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 6-13. Always use the proper fluid. Failure to use the proper fluid can cause leaks and damage hoses and seals.
Windshield Washer Fluid What to Use When you need windshield washer fluid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Adding Washer Fluid
Notice: (cid:129) When using concentrated washer fluid, follow
the manufacturer’s instructions for adding water.
(cid:129) Do not mix water with ready-to-use washer fluid.
Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system. Also, water does not clean as well as washer fluid. Fill the washer fluid tank only three-quarters full when it is very cold. This allows for fluid expansion if freezing occurs, which could damage the tank if it is completely full.
(cid:129) Do not use engine coolant (antifreeze) in your windshield washer. It can damage the vehicle’s windshield washer system and paint.
Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 5-14 for reservoir location.
5-33
(cid:129) Do not top off the brake fluid. Adding brake fluid does not correct a leak. If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed. Add or remove fluid, as necessary, only when work is done on the brake or clutch hydraulic system.
{ CAUTION:
If too much brake fluid is added, it can spill on the engine and burn, if the engine is hot enough. You or others could be burned, and the vehicle could be damaged. Add brake fluid only when work is done on the brake and/or clutch hydraulic system.
When the brake fluid falls to a low level, the brake warning light comes on. See Brake System Warning Light on page 3-28.
Brakes Brake Fluid
The vehicle has one reservoir for both the brake and clutch hydraulic systems. It is filled with DOT-3 brake fluid.
See Engine Compartment Overview on page 5-14 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down:
The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up.
(cid:129) A fluid leak in the brake or clutch hydraulic system can also cause a low fluid level. Have the brake or clutch hydraulic system fixed, since a leak means that sooner or later the brakes will not work well.
5-34
(cid:129) What to Add Use only new DOT-3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 6-13. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
{ CAUTION:
With the wrong kind of fluid in the brake or clutch hydraulic system, the brakes or clutch might not work well. This could cause a crash. Always use the proper brake fluid.
Notice: (cid:129) Using the wrong fluid can badly damage brake or clutch hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake or clutch hydraulic system can damage brake or clutch hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid. If brake fluid is spilled on the vehicle’s painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle. If you do, wash it off immediately. See Washing Your Vehicle on page 5-82.
5-35
(cid:129) Brake Wear This vehicle has front disc brakes and could have rear drum brakes or rear disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
{ CAUTION:
The brake wear warning sound means that soon the brakes will not work well. That could lead to an accident. When the brake wear warning sound is heard, have the vehicle serviced.
Notice: Continuing to drive with worn-out brake pads could result in costly brake repair. Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with the brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque specifications in Capacities and Specifications on page 5-93.
5-36
If the vehicle has rear drum brakes, they do not have wear indicators, but if a rear brake rubbing noise is heard, have the rear brake linings inspected immediately. Rear brake drums should be removed and inspected each time the tires are removed for rotation or changing. When the front brake pads are replaced, have the rear brakes inspected, too. Brake linings should always be replaced as complete axle sets. Brake Pedal Travel See your dealer/retailer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service might be required. Brake Adjustment Every moderate brake stop, the disc brakes adjust for wear. If rarely making moderate or heavier brake stops, the brakes might not adjust correctly. Very carefully making a few moderate brake stops about every 1,000 miles (1 600 km) will adjust the brakes properly. If the vehicle has rear drum brakes and the brake pedal goes down farther than normal, the rear drum brakes might need adjustment. Adjust them by backing up and firmly applying the brakes a few times.
Vehicle Storage
{ CAUTION:
Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 5-38 for tips on working around a battery without getting hurt.
Infrequent Usage: If the vehicle is driven infrequently, remove the black, negative (−) cable from the battery. This helps keep the battery from running down. Extended Storage: For extended storage of the vehicle, remove the black, negative (−) cable from the battery or use a battery trickle charger. This helps maintain the charge of the battery over an extended period of time.
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced — for example, when the brake linings wear down and new ones are installed — be sure to get new approved replacement parts. If this is not done, the brakes might not work properly. For example, if someone puts in brake linings that are wrong for the vehicle, the balance between the front and rear brakes can change — for the worse. The braking performance expected can change in many other ways if the wrong replacement brake parts are installed.
Battery This vehicle has a maintenance free battery. When it is time for a new battery, see your dealer/retailer for one that has the replacement number shown on the original battery’s label. See Engine Compartment Overview on page 5-14 for battery location. Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
5-37
Jump Starting If the vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.
{ CAUTION:
Batteries can hurt you. They can be dangerous because:
(cid:129) They contain acid that can burn you. (cid:129) They contain gas that can explode or ignite. (cid:129) They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you.
5-38
Ignoring these steps could result in costly
Notice: damage to the vehicle that would not be covered by the warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle. 1. Check the other vehicle. It must have a 12-volt
battery with a negative ground system.
If the other vehicle’s system is not a 12-volt
Notice: system with a negative ground, both vehicles can be damaged. Only use vehicles with 12-volt systems with negative grounds to jump start your vehicle. 2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles are not touching each other. If they are, it could cause a ground connection you do not want. You would not be able to start your vehicle, and the bad grounding could damage the electrical systems. To avoid the possibility of the vehicles rolling, set the parking brake firmly on both vehicles involved in the jump start procedure. Put an automatic transmission in P (Park) or a manual transmission in N (Neutral) before setting the parking brake.
If you leave the radio or other accessories
Notice: on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3. Turn off the ignition on both vehicles. Unplug
unnecessary accessories plugged into the cigarette lighter or the accessory power outlet. Turn off the radio and all lamps that are not needed. This will avoid sparks and help save both batteries. And it could save the radio!
4. Open the hoods and locate the batteries. Find the positive (+) and negative (−) terminal locations on each vehicle. See Engine Compartment Overview on page 5-14 for more information on location.
{ CAUTION:
An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.
{ CAUTION:
Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle. But if a battery has filler caps, be sure the right amount of fluid is there. If it is low, add water to take care of that first. If you don’t, explosive gas could be present. Battery fluid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately.
5-39
{ CAUTION:
Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.
5. Check that the jumper cables do not have loose or
missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative (−) will go to a heavy, unpainted metal engine part or to a remote negative (−) terminal if the vehicle has one. Do not connect positive (+) to negative (−) or you will get a short that would damage the battery and maybe other parts too. And do not connect the negative (−) cable to the negative (−) terminal on the dead battery because this can cause sparks.
5-40
6. Connect the red positive (+) cable to the positive (+)
terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one.
7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.
8. Now connect the black negative (−) cable to the negative (−) terminal of the good battery. Use a remote negative (−) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative (−) cable does not go to the dead battery. It goes to a heavy, unpainted metal engine part or to a remote negative (−) terminal on the vehicle with the dead battery.
5-41
9. Connect the other end of the negative (−) cable at
least 18 inches (45 cm) away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, and the chance of sparks getting back to the battery is much less.
10. Now start the vehicle with the good battery and run
the engine for a while.
11. Try to start the vehicle that had the dead battery.
If it will not start after a few tries, it probably needs service.
If the jumper cables are connected or
Notice: removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
5-42
Jumper Cable Removal
A. Heavy, Unpainted Metal Engine Part or Remote
Negative (–) Terminal
B. Good Battery or Remote Positive (+) and Remote
Negative (−) Terminals
C. Dead Battery or Remote Positive (+) Terminal
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the
vehicle that had the dead battery.
2. Disconnect the black negative (−) cable from the
vehicle with the good battery.
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-49. For any bulb changing procedure not listed in this section, contact your dealer/retailer.
3. Disconnect the red positive (+) cable from the
vehicle with the good battery.
Halogen Bulbs
4. Disconnect the red positive (+) cable from the other
vehicle.
Headlamp Aiming Headlamp aim has been preset at the factory and should need no further adjustment. However, if your vehicle is damaged in a crash, the headlamp aim may be affected. Aim adjustment to the low-beam headlamps may be necessary if oncoming drivers flash their high-beam headlamps at you (for vertical aim). If the headlamps need to be re-aimed, it is recommended that you take the vehicle to your dealer/retailer for service.
{ CAUTION:
Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.
5-43
Headlamps To replace a headlamp bulb: 1. Open the hood. See Hood Release on page 5-12.
4. Remove the headlamp cap. 5. Release the spring that retains the bulb by
loosening the screw.
6. Remove the old bulb and install the new bulb. 7. Install the bulb retaining spring and tighten
the screw.
8. Reinstall the headlamp cap. 9. Reconnect the wiring harness at the rear of
the bulb.
2. Remove the three bolts to remove the headlamp
assembly.
3. Disconnect the wiring harness connector from the
rear of the bulb.
5-44
10. Reinstall the headlamp assembly using the
three bolts.
Front Turn Signal, Sidemarker and
Parking Lamps
To replace a front turn signal or parking lamp bulb:
1. Open the hood. See Hood Release on page 5-12
for more information.
2. Remove the three bolts to remove the headlamp
assembly.
3. Disconnect the wiring harness connector from the
rear of the bulb.
5-45
4. Turn the front turn signal bulb socket
counterclockwise.
10. Reinstall the headlamp assembly using the
three bolts.
5. Pull the front turn signal bulb socket out of the lamp
housing.
6. Press the bulb inward and turn it counterclockwise
to remove it from the bulb socket.
7. Install the new bulb into the socket by pressing it in
and turning it clockwise.
8. Install the socket into the lamp housing by turning it
clockwise.
9. Reconnect the wiring harness connector at the rear
of the bulb.
5-46
Center High-Mounted Stoplamp (CHMSL) (Hatchback) To replace a CHMSL bulb on the hatchback: 1. Open the liftgate. See Liftgate (Hatchback) on
page 2-10 for more information.
Center High-Mounted Stoplamp (CHMSL) (Sedan) To replace a CHMSL bulb on the sedan: 1. Open the trunk. See Trunk (Sedan) on page 2-8 for
more information.
2. Remove the two screws and the lamp housing. Disconnect the wiring harness connector before removing the lamp housing.
2. Pull down on the lamp assembly while holding the
end of the bracket.
3. Remove the lens cover using a flat head
screwdriver.
4. Remove the bulb by pulling it straight out of the
bulb holder.
5. Install the new bulb. 6. Reverse Steps 1 through 3 to reinstall.
3. Remove the five screws and the reflector assembly. 4. Remove the bulb by pulling it straight out of the
bulb holder.
5. Install the new bulb. 6. Reverse Steps 1 through 3 to reinstall.
5-47
Taillamps, Turn Signal, Sidemarker, Stoplamps and Back-up Lamps To replace a taillamp, turn signal lamp, stoplamp, or back-up bulb: 1. Open the liftgate or trunk. See Liftgate (Hatchback)
on page 2-10 or Trunk (Sedan) on page 2-8.
Sedan
2. Remove the two screws and the lamp assembly. 3. Turn the bulb socket counterclockwise and remove
the socket.
4. Press the bulb in and turn counterclockwise to
remove from the socket.
5. Press the new bulb in and turn clockwise to install
the bulb into the socket.
6. Turn the bulb socket clockwise to reinstall. 7. Reinstall the lamp assembly and two screws.
Hatchback
5-48
License Plate Lamp To replace one of these bulbs:
1. Remove the two screws holding each of the license
plate lamps.
2. Turn and pull the license plate lamp toward you
through the opening.
3. Turn the bulb socket counterclockwise and pull the
bulb straight out of the socket.
4. Install the new bulb. 5. Push the bulb straight into the socket and turn
clockwise to reinstall.
6. Push and turn the license plate lamp away from
you through the opening.
7. Reinstall the two screws holding the license
plate lamp.
Replacement Bulbs
Exterior Lamp
Bulb Number
Back-Up Lamps Center High-Mounted Stoplamp (CHMSL) Front Parking/Turn Signal Lamps Front Sidemarker Lamps Headlamps License Plate Lamp Rear Sidemarker Lamps Rear Turn Signal Lamps Stoplamp/Taillamps
94535571
94535587
94535578
94535578
94535548
94535587
94535577
94535572
94535577
For replacement bulbs not listed here, contact your dealer/retailer.
5-49
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See “Wiper Blade Check” for more information. Replacement blades come in different types and are removed in different ways. For the proper type, see Maintenance Replacement Parts on page 6-15.
Here is how to remove and replace the windshield wiper blade: 1. Pull the windshield wiper arm away from the
windshield.
2. Press the retaining clip (A) and pull the wiper blade
off the arm.
3. Install a new blade by reversing Steps 1 and 2.
5-50
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer.
{ CAUTION:
Poorly maintained and improperly used tires are dangerous.
(cid:129) Overloading your vehicle’s tires can cause overheating as a result of too much flexing. You could have an air-out and a serious accident. See Loading the Vehicle on page 4-16.
CAUTION:
(Continued)
CAUTION:
(Continued)
(cid:129) Underinflated tires pose the same danger
as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your vehicle’s tires are cold. See Inflation - Tire Pressure on page 5-57.
(cid:129) Overinflated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when you hit a pothole. Keep tires at the recommended pressure.
(cid:129) Worn, old tires can cause accidents.
If the tire’s tread is badly worn, or if your vehicle’s tires have been damaged, replace them.
5-51
Tire Sidewall Labeling Usefulinformation about a tire is molded into its sidewall. The examples below show a typical passenger car tire and a compact spare tire sidewall.
Passenger Car Tire Example
5-52
(A) Tire Size: The tire size is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail. (B) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. (C) Tire Identification Number (TIN): The letters and numbers following DOT code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (D) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (E) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction and temperature resistance. For more information see Uniform Tire Quality Grading on page 5-66.
(F) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. For information on recommended tire pressure see Inflation - Tire Pressure on page 5-57 and Loading the Vehicle on page 4-16.
Compact Spare Tire Example (A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h).
The compact spare tire is for emergency use when a regular road tire has lost air and gone flat. See Compact Spare Tire on page 5-78 and If a Tire Goes Flat on page 5-69. (B) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (C) Tire Identification Number (TIN): The Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (D) Maximum Cold Inflation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. See Compact Spare Tire on page 5-78 and Loading the Vehicle on page 4-16. (E) Tire Inflation: The temporary use tire or compact spare tire should be inflated to 60 psi (420 kPa). For more information on tire pressure and inflation see Inflation - Tire Pressure on page 5-57. (F) Tire Size : A combination of letters and numbers define a tire’s width, height, aspect ratio, construction type and service description. The letter T as the first character in the tire size means the tire is for temporary use only.
5-53
Tire Size The following illustration shows an example of a typical passenger car tire size.
(A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U. S. Tire and Rim Association. (B) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 70, as shown in item C of the illustration, it would mean that the tire’s sidewall is 70% as high as it is wide.
5-54
(D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches. (F) Service Description: These characters represent the load index and speed rating of the tire. The load index represents the load carry capacity a tire is certified to carry. The speed rating is the maximum speed a tire is certified to carry a load.
Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning.
Aspect Ratio: The relationship of a tire’s height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inflation - Tire Pressure on page 5-57. Curb Weight: The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) motor vehicle safety standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand, and date of production.
GVWR: Gross Vehicle Weight Rating. See Loading the Vehicle on page 4-16. GAWR FRT: Gross Axle Weight Rating for the front axle. See Loading the Vehicle on page 4-16. GAWR RR: Gross Axle Weight Rating for the rear axle. See Loading the Vehicle on page 4-16. Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire can be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inflation pressure for that tire.
5-55
Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1/16 inch (1.6 mm) of tread remains. See When It Is Time for New Tires on page 5-63.
Maximum Loaded Vehicle Weight: The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading the Vehicle on page 4-16. Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer’s recommended tire inflation pressure as shown on the tire placard. See Inflation - Tire Pressure on page 5-57 and Loading the Vehicle on page 4-16.
5-56
UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 5-66. Vehicle Capacity Weight: The number of designated seating positions multiplied by 150 lbs (68 kg) plus the rated cargo load. See Loading the Vehicle on page 4-16. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle’s capacity weight and the original equipment tire size and recommended inflation pressure. See “Tire and Loading Information Label” under Loading the Vehicle on page 4-16.
Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right. It is not. If your tires do not have enough air (under-inflation), you can get the following: