2008 Cadillac Escalade Premium Owners Manual

Download PDF Manual
CAUTION: (Continued) 2-39 Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 2-39. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 4-30. It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into PARK (P) on page 2-36. If you are pulling a trailer, see Towing a Trailer on page 4-44. 2-40 Mirrors Automatic Dimming Rearview Mirror with Intellibeam®, OnStar®, Compass, and Temperature Display Your vehicle may have an automatic dimming rearview mirror with Intellibeam®, OnStar®, compass and temperature display. For more information on OnStar®, see OnStar® System on page 2-50. For more information on Intellibeam®, see “Intellibeam® Intelligent High-Beam Headlamp Control System” under Exterior Lamps on page 3-16. The mirror includes an eight-point compass display in the upper right corner of the mirror face. When on, the compass automatically calibrates as the vehicle is driven. Outside temperature is also shown in the display. Automatic Dimming Your vehicle has an inside automatic dimming rearview mirror. The automatic dimming feature is activated whenever the vehicle is turned on and dims only during nighttime driving. Compass Operation AUTO 3: Press and hold the “auto highbeam” button for about three seconds to turn the compass/temperature display on or off. When the ignition and the display features are on, the display will show two character boxes for about two seconds. After two seconds, the mirror will display the compass heading and temperature. Compass Calibration If after two seconds the display does not show the correct direction, (N for North for example), there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder, or a similar magnetic item. The compass can be placed in calibration mode manually by pressing and holding the “auto highbeam” button for about nine seconds until CAL is shown in the compass display. The mirror can then be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads the correct direction. 2-41 Compass Variance The mirror is set to zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if the vehicle is driven outside zone eight. Under certain circumstances, such as a long distance, cross-country trip, it will be necessary to adjust the compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If the mirror is not adjusted to account for zone changes, the compass could give false readings. To adjust for zone changes: 1. Find your current location and variance zone number on the zone map that follows. 2-42 2. Press and hold the “auto highbeam” button about six seconds until a zone number appears in the display. 3. Once the zone number appears in the display, press the “auto highbeam” button quickly until you reach the correct zone number. Stop pressing the button and the mirror will return to normal operation. If C appears in the compass window, the compass needs calibration. See “Compass Calibration” listed previously. Outside Temperature Outside temperature is shown in the mirror display. Temperature will be displayed in Fahrenheit or Celsius based on the choice of English or metric in the vehicle’s conﬁguration menu. If an abnormal temperature reading is displayed for an extended period of time, please consult your dealer/retailer. Under certain circumstances, a delay in updating the temperature is normal. Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display Your vehicle has this feature. When on, the automatic dimming mirror dims to the proper level to minimize glare from lights behind you after dark. The mirror has a dual display in the upper right corner of the mirror face that shows the compass reading and the outside temperature. Control buttons for the OnStar® system are at the bottom of the mirror. See OnStar® System on page 2-50 for more information about the services OnStar® provides. P(On/Off): This is the on/off button. Temperature and Compass Display Press the on/off button, located to the far left, brieﬂy to turn the compass/temperature display on or off. If the display reads CAL, the compass needs to be calibrated. For more information, see “Compass Calibration” following. To adjust between Fahrenheit and Celsius, do the following: 1. Press and hold the on/off button for approximately four seconds until either a ﬂashing F or C appears. 2. Press the button again to change the display to the desired unit of measurement. After approximately four seconds of inactivity, the new unit will be locked in and the compass/temperature display will return. If an abnormal temperature reading is displayed for an extended period of time, please see your GM dealer. Under certain circumstances, a delay in updating the temperature is normal. 2-43 Automatic Dimming Mirror Operation The automatic dimming mirror function is turned on automatically each time the ignition is started. To operate the automatic dimming mirror, do the following: 1. Make sure the green indicator light, located to the left of the on/off button, is lit. If it is not, press and hold the on/off button for approximately six seconds until the green light comes on, indicating that the mirror is in automatic dimming mode. 2. Turn off the automatic dimming mirror function by pressing and holding the on/off button for approximately six seconds, until the green indicator light turns off. Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if the vehicle is outside of zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, the compass could give false readings. 2-44 To adjust for compass variance, do the following: 1. Find your current location and variance zone number on the following zone map. 2. Press and hold the on/off button until a Z and a zone number appears in the display. The compass is now in zone mode. 3. Keep pressing the on/off button until the desired zone number appears in the display. Release the button. After approximately four seconds of inactivity, the new zone number will be locked in and the compass/temperature display will return. 4. Calibrate the compass as described next. Compass Calibration The compass may need calibration if one of the following occurs: (cid:129) After approximately ﬁve seconds, the display does not show a compass heading, N for North, for example, there may be a strong magnetic ﬁeld interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder, or a similar magnetic item. The compass does not display the correct heading and the compass zone variance is set correctly. In order to calibrate, CAL must be displayed in the mirror compass windows. If CAL is not displayed, push the on/off button for approximately 12 seconds or until CAL is displayed. The compass can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Outside Power Foldaway Mirrors If your vehicle is equipped with outside power foldaway mirrors, the controls are located on the driver’s door armrest. (cid:129) Press (A) to select the driver’s side mirror. Then press the arrows located on the four-way control pad to adjust the mirror. Press (A) again to deselect the mirror. (cid:129) Press (B) to select the passenger’s side mirror. Then press the arrows located on the four-way control pad to adjust the mirror. Press (B) again to deselect the mirror. 2-45 (cid:129) Automatic Dimming The driver’s outside mirror will adjust for the glare of the headlamps behind you. See Automatic Dimming Rearview Mirror with OnStar®, Compass and Temperature Display on page 2-43. Park Tilt Mirrors If your vehicle has the memory package, the outside mirrors are able to perform the park tilt function. This feature may be useful in allowing the driver to view the curb when parallel parking. This feature will cause the passenger’s and/or driver’s mirror to tilt to a preselected position when the vehicle is in REVERSE (R). The passenger’s and/or driver’s mirror will return to its original position when the vehicle is shifted out of REVERSE (R), or the ignition is turned off or to OFF/LOCK. This feature can be turned on or off through the Driver Information Center (DIC). See DIC Vehicle Customization on page 3-61. (cid:129) Press (C) to fold the mirrors out to the driving position. (cid:129) Press (D) to fold the mirrors in to the folded position. If the mirrors are accidentally folded/unfolded manually, they may shake or ﬂutter at normal driving speeds and may not stay in the unfolded position. If this happens, you will need to reset the mirrors. See “Resetting the Power Foldaway Mirrors” next. Resetting the Power Foldaway Mirrors You will need to reset the power foldaway mirrors if the following occurs: The mirrors are accidentally obstructed while folding. They are accidentally manually folded/unfolded. The mirrors will not stay in the unfolded position. The mirrors shake and ﬂutter at normal driving speeds. To reset the power foldaway mirrors, fold and unfold them one time using the mirror controls. This will reset them to their normal position. This mirror has the following features. 2-46 (cid:129) (cid:129) (cid:129) (cid:129) Heated Mirrors The button to turn the heated mirrors on or off is located on the climate control panel. Press this button to warm the driver’s and passenger’s outside rearview mirrors to help clear them of ice, snow, and condensation. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 3-26 for more information. Convex Mirror {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. The passenger’s side mirror may have convex glass. A convex mirror’s surface is curved so more can be seen from the driver’s seat. Your vehicle may also have a turn signal indicator on the mirror. An arrow on the mirror will ﬂash in the direction of the turn or lane change. 2-47 Object Detection Systems Ultrasonic Rear Parking Assist (URPA) If your vehicle has the Ultrasonic Rear Parking Assist (URPA) system, it helps you park easier and avoid other vehicles while in REVERSE (R). It operates at speeds less than 5 mph (8 km/h). It can determine how close objects are to the rear bumper, up to 8 feet (2.5 m) behind your vehicle. The distance sensors are located on the rear bumper. {CAUTION: The Ultrasonic Rear Parking Assist (URPA) system does not replace driver vision. It cannot detect: (cid:129) objects that are below the bumper, underneath the vehicle, or if they are too close or far from the vehicle (cid:129) children, pedestrians, bicyclists, or pets. CAUTION: (Continued) 2-48 CAUTION: (Continued) If you do not use proper care before and while backing; vehicle damage, injury, or death could occur. Even with URPA, always check behind your vehicle before backing up. While backing, be sure to look for objects and check your vehicle’s mirrors. On some vehicles this display is located near the passenger side rear window and can be seen by looking over your right shoulder. If your vehicle has the display, there are three color-coded lights to provide distance and system information. If your vehicle does not have the display and it has URPA, you will hear the beeps as described in the following information. How the System Works URPA comes on automatically when the shift lever is moved into REVERSE (R). The rear display will then brieﬂy illuminate to let you know the system is working. URPA operates only at speeds less than 5 mph (8 km/h). If you are above this speed, the red light on the rear display will ﬂash. To be detected, objects must be at least 10 inches (25.4 cm) off the ground and below liftgate level. Objects must also be within 8 feet (2.5 m) from your rear bumper. This distance may be less during warmer or humid weather. A single beep will sound the ﬁrst time an object is detected between 20 inches (0.5 m) and 8 feet (2.5 m) away. Beeping will occur for three seconds when you are closer than 1 foot (0.3 m) from the object. The following describes what will occur with the URPA display as you get closer to a detected object: Description amber light amber/amber lights amber/amber/red lights amber/amber/red lights ﬂashing and beep for three seconds English 8 ft 40 in 23 in 1 ft Metric 2.5 m 1.0 m 0.6 m 0.3 m The system can be disabled by pressing the rear park aid disable button located next to the radio. The indicator light will come on to indicate that URPA is off. 2-49 OnStar® System OnStar uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location. If you lock your keys in the vehicle, call OnStar at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar button and they can contact Roadside Service for you. When the System Does Not Seem to Work Properly The driver disables the system. The parking brake pedal is depressed. The ultrasonic sensors are not clean. Keep your vehicle’s rear bumper free of mud, dirt, snow, ice and slush. For cleaning instructions, see Washing Your Vehicle on page 5-102. (cid:129) A trailer was attached to your vehicle, or a bicycle or an object was hanging out of your liftgate/liftglass during your last drive cycle, the red light may illuminate in the rear display. Once the attached object is removed, URPA will return to normal operation. (cid:129) A tow bar is attached to your vehicle. The vehicle’s bumper is damaged. Take the vehicle to your dealer/retailer to repair the system. (cid:129) Other conditions may affect system performance, such as vibrations from a jackhammer or the compression of air brakes on a very large truck. If the system is still disabled, after driving forward at least 15 mph (25 km/h), take your vehicle to your dealer/retailer. 2-50 (cid:129) (cid:129) (cid:129) (cid:129) OnStar service is provided to you subject to the OnStar Terms and Conditions. You may cancel your OnStar service at any time by contacting OnStar. A complete OnStar Owner’s Guide and the OnStar Terms and Conditions are included in the vehicle’s OnStar Subscriber glove box literature. For more information, visit onstar.com or onstar.ca, contact OnStar at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar button to speak with an OnStar advisor 24 hours a day, 7 days a week. Not all OnStar features are available on all vehicles. To check if your vehicle is equipped to provide the services described below, or for a full description of OnStar services and system limitations, see the OnStar Owner’s Guide in your glove box or visit onstar.com. OnStar Services For new vehicles with OnStar, the Safe & Sound Plan, or the Directions & Connections Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions & Connections Plan. For more information, press the OnStar button to speak with an advisor. Some OnStar services (such as Remote Door Unlock or Stolen Vehicle Location Assistance) may not be available until you register with OnStar. Available Services with Safe & Sound Plan (cid:129) Automatic Notiﬁcation of Airbag Deployment (cid:129) Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) Link to Emergency Services (cid:129) Roadside Assistance (cid:129) Stolen Vehicle Location Assistance (cid:129) AccidentAssist (cid:129) Remote Door Unlock/Vehicle Alert (cid:129) OnStar Vehicle Diagnostics (cid:129) GM Goodwrench® On Demand Diagnostics (cid:129) OnStar Hands-Free Calling with 30 complimentary minutes (cid:129) OnStar Virtual Advisor (U.S. Only) Available Services included with Directions & Connections Plan (cid:129) All Safe and Sound Plan Services (cid:129) Driving Directions - Advisor delivered or OnStar Turn-by-Turn Navigation (If equipped) (cid:129) RideAssist Information and Convenience Services 2-51 (cid:129) (cid:129) OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Hands-Free Calling may also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To ﬁnd out more, refer to the OnStar Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar advisor by pressing the OnStar button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar Owner’s Guide for more information (Only available in the continental U.S.). 2-52 OnStar Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-106 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” to activate the OnStar Hands-Free Calling. On some vehicles, the mute button can be used to dial numbers into voicemail systems, or to dial phone extensions. See the OnStar Owner’s Guide for more information. How OnStar Service Works Your vehicle’s OnStar system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar Call Center at the time of an OnStar button press, Emergency button press or if your airbags or AACN system deploys. The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar Hands-Free Calling, your vehicle also sends OnStar your GPS location so that we can provide you with location-based services. OnStar service cannot work unless your vehicle is in a place where OnStar has an agreement with a wireless service provider for service in that area. OnStar service also cannot work unless you are in a place where the wireless service provider OnStar has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. Location information about your vehicle is only available if the GPS satellite signals are unobstructed and available. Your vehicle must have a working electrical system (including adequate battery power) for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility Increase the radio volume if you cannot hear the OnStar advisor. If the light next to the OnStar buttons is red, this means that your system is not functioning properly and should be checked by your dealer/retailer. If the light appears clear (no light is appearing), your OnStar subscription has expired. You can always press the OnStar button to conﬁrm that your OnStar equipment is active. Universal Home Remote System Universal Home Remote System The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 2-53 This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Universal Home Remote System Operation (With Three Round LED) Your vehicle may have the Universal Home Remote System. If there are three round Light Emitting Diode (LED) indicator lights above the Universal Home Remote buttons, follow the instructions below. 2-54 This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. Do not use this system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the transmitter. Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter. Be sure to keep the original remote control transmitter for use in other vehicles, as well as, for future programming. You only need the original remote control transmitter for Fixed Code programming. It is also recommended that upon the sale or lease termination of the vehicle, the programmed buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section. When programming a garage door, it is advised to park outside of the garage. Be sure that people and objects are clear of the garage door or security device you are programming. Programming Universal Home Remote — Rolling Code If you have questions or need help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. To program up to three devices: 1. From inside the vehicle, press the two outside buttons at the same time for one to two seconds, and immediately release them. 2. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. It can usually be found where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Press this button. After you press this button, you will have 30 seconds to complete the following steps. 3. Immediately return to your vehicle. Press and hold the Universal Home Remote button that you would like to use to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. You may need to hold the button from ﬁve to 20 seconds. 2-55 4. Immediately, within one second, release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 5. Press and release the same button again. The garage door should move, conﬁrming that programming is successful and complete. To program up to three devices: To program another Rolling Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1 through 5, choosing a different function button in Step 3 than what you used for the garage door opener. If these instructions do not work, you probably have a Fixed Code garage door opener. Follow the Programming instructions that follow for a Fixed Code garage door opener. Programming Universal Home Remote — Fixed Code If you have questions or need help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold before 1996 are Fixed Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. 2-56 1. To verify if you have a Fixed Code garage door opener, remove the battery cover on your hand held transmitter supplied by the manufacturer of your garage door opener motor. If you see a row of dip switches similar to the graphic above, you have a Fixed Code garage door opener. If you do not see a row of dip switches, return to the previous section for Programming Universal Home Remote – Rolling Code. Your hand held transmitter may have between eight to 12 dip switches depending on the brand of transmitter. Your garage door opener receiver (motor head unit) may also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head and hand held transmitter are different, or if the dip switch settings are different, use the dip switch settings on the motor head unit to program your Universal Home Remote. The motor head dip switch settings can also be used when you do not have the original hand held transmitter. Example of Eight Dip Switches with Two Positions Example of Eight Dip Switches with Three Positions Your panel of switches may not appear exactly as they do in the examples, but they should be similar. The switch positions on your hand-held transmitter may be labeled as follows: (cid:129) A switch in the up position may be labeled as “Up,” “+,” or “On.” (cid:129) A switch in the down position may be labeled as “Down,” “−,” or “Off.” (cid:129) A switch in the middle position may be labeled as “Middle,” “0,” or “Neutral.” 2-57 2. Write down the eight to 12 switch settings from left to right as follows: (cid:129) When a switch is in the up position, write “Left.” (cid:129) When a switch is in the down position, write “Right.” If a switch is set between the up and down position, write “Middle.” The switch settings that you wrote down in Step 2 will now become the button strokes you enter into the Universal Home Remote in Step 4. Be sure to enter the switch settings that you wrote down in Step 2, in order from left to right, into the Universal Home Remote, when completing Step 4. 3. From inside your vehicle, ﬁrst ﬁrmly press all three buttons at the same time for about three seconds. Release the buttons to put the Universal Home Remote into programming mode. 4. The indicator lights will blink slowly. Enter each switch setting from Step 2 into your vehicle’s Universal Home Remote. You will have two and one-half minutes to complete Step 4. Now press one button on the Universal Home Remote for each switch setting as follows: If you wrote “Left,” press the left button in the vehicle. If you wrote “Right,” press the right button in the vehicle. If you wrote “Middle,” press the middle button in the vehicle. 2-58 (cid:129) (cid:129) (cid:129) (cid:129) 5. After entering all of the switch positions, again, ﬁrmly press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button you would like to use to control the garage door until the garage door moves. The indicator light above the selected button should slowly blink. You may need to hold the button from ﬁve to 55 seconds. 7. Immediately release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 8. Press and release the same button again. The garage door should move, conﬁrming that programming is successful and complete. To program another Fixed Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1-8, choosing a different button in Step 6 than what you used for the garage door opener. Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted. Reprogramming Universal Home Remote Buttons You can reprogram any of the three buttons by repeating the instructions. Erasing Universal Home Remote Buttons You should erase the programmed buttons when you sell or terminate your lease. To erase either Rolling Code or Fixed Code on the Universal Home Remote device: 1. Press and hold the two outside buttons at the same time for approximately 20 seconds, until the indicator lights, located directly above the buttons, begin to blink rapidly. 2. Once the indicator lights begin to blink, release both buttons. The codes from all buttons will be erased. For help or information on the Universal Home Remote System, call the customer assistance phone number under Customer Assistance Offices on page 7-5. 2-59 Storage Areas Glove Box Open the glove box by pulling the bottom of the handle upward. Use the key to lock and unlock. Cupholder(s) Your vehicle has cupholders for the front and rear passengers. The cupholders are located in the center console for the front passengers and on the rear of the center console for the rear passengers. To use the front cupholders, press down on the access door release. The door will then open. Push the door pack down to close it. The front cupholder may be removed for cleaning by pushing down and then back on the cupholder. 2-60 To access the cupholders in the rear ﬂoor console, pull downward on the lid. Center Console Storage Your vehicle has a console compartment between the bucket seats. The console has both an upper and lower storage bin accessed by lifting up on the latches located at the front of the console lid. The console may have an accessory power outlet inside. See Accessory Power Outlet(s) on page 3-24. The rear of the console also has a cupholder that swings down for the rear seat passengers to use. Assist Handles Your vehicle is equipped with assist handles to be used when getting out of the vehicle. They are located above the rear passenger doors. Pull down to use. Garment Hooks There are garment hooks located on the assist handles. Luggage Carrier If your vehicle has a luggage carrier, you can load things on top of your vehicle. The luggage carrier has siderails attached to the roof and crossrails, if equipped, which can be moved back and forth to help secure cargo. To adjust, turn the knob located at each end of the crossrail counterclockwise until the crossrail can move freely. To secure the crossrail, turn the knob located at each end of the crossrail clockwise until tightened. Tie the load to the siderails or siderail supports. Notice: Loading cargo on the luggage carrier that weighs more than 200 lbs (91 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests as far forward as possible and against the side rails, making sure to fasten it securely. Do not exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 4-35. 2-61 To prevent damage or loss of cargo as you are leaving, check now and then to make sure the luggage and cargo are still securely fastened. Be sure the cargo is properly loaded. If small heavy objects are placed on the roof, place the load in the area over the rear wheels (behind the rear side door on extended models). If you need to, cut a piece of 3/8 inch plywood to ﬁt inside the crossrails and siderails to spread the load. If plywood is used, tie it to the siderail supports. Tie the load to the crossrails or the siderail supports. Use the crossrails only to keep the load from sliding. To move the crossrails, pull out on the latch release handle at each end. Slide the crossrail to the desired position balancing the force side to side. Push the release handle back into the latched position and slide the crossrail back and forth slightly to be sure the latch snaps securely into place. If you need to carry long items, move the crossrails as far apart as they will go. Tie the load to the crossrails and the siderails or siderail supports. Also tie the load to the bumpers. Do not tie the load so tightly that the crossrails or siderails are damaged. (cid:129) After moving a crossrail, be sure it is securely locked into the siderail. Your vehicle has a Center High-Mounted Stoplamp (CHMSL) located above the glass or above the rear load doors. If items are loaded on the roof of the vehicle, care should be taken not to block or damage the CHMSL unit. Rear Storage Area Your vehicle may have a storage compartment located in the rear cargo area of the vehicle in the driver’s side trim panel. To open the utility compartment, turn the knobs and swing the compartment door open. The compartment door can be removed. Rear Seat Armrest Your vehicle’s second row seat may have an armrest/storage compartment. Pull the loop at the top of the armrest out to lower the armrest. To open the compartment, push the button on the front of the armrest and pull the top open. 2-62 (cid:129) (cid:129) (cid:129) Convenience Net Your vehicle may have a convenience net in the rear of the vehicle. Store small loads as far forward as possible. The net should not be used to store heavy loads. Cargo Cover {CAUTION: An improperly stored cargo cover could be thrown about the vehicle during a collision or sudden maneuver. You or others could be injured. If you remove the cover, always store it in the proper storage location. When you put it back, always be sure that it is securely reattached. If your vehicle has a cargo cover, you can use it to cover items in the cargo area of your vehicle. To use the cover, do the following: 1. Pull the cover handle toward the rear of the vehicle. 2. Latch the cover posts into the retaining sockets on the cargo area trim panels. To return the cover to the retracted position, do the following: 1. Pull up on the cover handle to release the cover posts from the retaining sockets. 2. Let the cover move forward to the full retracted position. To remove the cover, from a regular wheelbase model, do the following: 1. Let the cover go all the way into the holder. 2. Then, grasping the driver’s side cover end cap, push the cover end cap toward the passenger’s side of the vehicle. 3. Swing the cover rearward and take it out of the vehicle. To put the cover in the vehicle, do the following: 1. Make sure the cover slot in the holder faces rearward with the round surface facing down. 2. Then, hold the cover at an angle and place the cover end cap into the slot in the passenger’s side trim panel. 3. Move the other end of the cover forward and hold it next to the driver’s side trim panel slot. 2-63 4. Press the end caps in, this will allow the cover to ﬁt into the trim slot. 5. Lightly pull on the cover holder to make sure it is secure. On the extended wheelbase models there are two cover positions. The slots furthest forward allow the cover to be used if the third seat is removed or folded down. The cover can be installed and removed from either side. Cargo Tie Downs Your vehicle may have cargo tie downs in the rear cargo area that allow you to strap cargo in and keep it from moving inside the vehicle. Sunroof Your vehicle may be equipped with a power sliding sunroof. To open or close the sunroof, the ignition needs to be turned to ON, or Retained Accessory Power (RAP) must be active. When RAP is active, the sunroof will work for 10 minutes after the ignition is turned off, or until a front door is opened. See Retained Accessory Power (RAP) on page 2-26 for more information. 2-64 There are two switches in the overhead console that operate the sunroof. Manual-Open/Manual-Close: To open the sunroof press and hold the rear of the driver’s side switch until the sunroof reaches the desired position. To close the sunroof, press and hold the front of the driver’s side switch until the sunroof reaches the desired position. The sunshade will open automatically with the sunroof, but can also be opened manually. The sunroof has a comfort stop feature which stops the sunroof from opening to the full-open position. From the comfort stop position, press the rear of the driver’s side switch a second time to open the sunroof to the full-open position. When the sunroof is opened, an air deﬂector will automatically raise. The air deﬂector will retract when the sunroof is closed. Express-Open/Express-Close: To express-open the sunroof, fully press and release the rear of the driver’s side switch. The sunroof will open automatically. To stop the sunroof partway, press the switch a second time. To express-close the sunroof, fully press and release the front of the driver’s side switch. The sunroof will close automatically. To stop the sunroof partway, press the switch a second time. The sunshade will open automatically with the sunroof, but can also be opened manually. The sunroof has a comfort stop feature which stops the sunroof from opening to the full-open position. From the comfort stop position, press the rear of the driver’s side switch a second time to open the sunroof to the full-open position. When the sunroof is opened, an air deﬂector will automatically raise. The air deﬂector will retract when the sunroof is closed. Vent: The sunroof has an express-vent open feature. From the closed position, press the rear of the passenger’s side switch to vent the sunroof. To stop the sunroof partway, press the switch a second time. To close the sunroof, press and hold the front of the passenger’s side switch. To stop the sunroof partway, release the switch. Anti-Pinch Feature: If an object is in the path of the sunroof while it is closing, the anti-pinch feature will detect the object and stop the sunroof from closing at the point of the obstruction. The sunroof will then open halfway, and the air deﬂector will raise. To close the sunroof once it has re-opened, refer to the “Express-Close” or “Manual-Close” functions described previously. If the sunroof is in the vent position, and there is an object in the path of the sunroof when it closing, the anti-pinch feature will detect the object and stop the sunroof. To close the sunroof once it has re-opened, refer to the “Manual-Close” or “Express-Close” functions described previously. 2-65 ✍ NOTES 2-66 Section 3 Instrument Panel Instrument Panel Overview ...............................3-4 Hazard Warning Flashers ................................3-6 Other Warning Devices ...................................3-6 Horn .............................................................3-6 Tilt Wheel .....................................................3-6 Heated Steering Wheel ...................................3-7 Turn Signal/Multifunction Lever .........................3-7 Turn and Lane-Change Signals ........................3-8 Headlamp High/Low-Beam Changer ..................3-9 Windshield Wipers ..........................................3-9 Rainsense™ II Wipers ...................................3-10 Windshield Washer .......................................3-11 Rear Window Wiper/Washer ...........................3-12 Cruise Control ..............................................3-13 Exterior Lamps .............................................3-16 Headlamps on Reminder ................................3-19 Daytime Running Lamps (DRL) .......................3-20 Automatic Headlamp System ..........................3-20 Fog Lamps ..................................................3-21 Instrument Panel Brightness ...........................3-21 Dome Lamps ...............................................3-22 Dome Lamp Override ....................................3-22 Entry Lighting ...............................................3-22 Exit Lighting .................................................3-22 Reading Lamps ............................................3-22 Electric Power Management ...........................3-23 Battery Run-Down Protection ..........................3-23 Accessory Power Outlet(s) .............................3-24 Ashtray(s) and Cigarette Lighter ......................3-25 Analog Clock ...............................................3-25 Climate Controls ............................................3-26 Dual Automatic Climate Control System ...........3-26 Outlet Adjustment .........................................3-31 Rear Air Conditioning and Heating System and Electronic Climate Controls .........................3-31 Warning Lights, Gages, and Indicators ............3-33 Instrument Panel Cluster ................................3-34 Speedometer and Odometer ...........................3-35 Trip Odometer ..............................................3-35 Tachometer .................................................3-35 Safety Belt Reminders ...................................3-35 Airbag Readiness Light ..................................3-36 Passenger Airbag Status Indicator ...................3-37 Charging System Light ..................................3-39 Brake System Warning Light ..........................3-40 Antilock Brake System Warning Light ...............3-41 StabiliTrak® Indicator Light ..............................3-41 Engine Coolant Temperature Gage ..................3-42 Tire Pressure Light .......................................3-42 Malfunction Indicator Lamp .............................3-43 Oil Pressure Light .........................................3-46 3-1 Section 3 Instrument Panel Security Light ...............................................3-46 Fog Lamp Light ............................................3-46 Lights On Reminder ......................................3-47 Cruise Control Light ......................................3-47 Highbeam On Light .......................................3-47 Tow/Haul Mode Light ....................................3-47 Fuel Gage ...................................................3-48 Driver Information Center (DIC) .......................3-48 DIC Operation and Displays ...........................3-49 DIC Warnings and Messages .........................3-53 DIC Vehicle Customization .............................3-61 Audio System(s) .............................................3-70 Setting the Clock ..........................................3-71 Radio(s) ......................................................3-72 Using an MP3 ..............................................3-90 XM Radio Messages .....................................3-94 Navigation/Radio System ...............................3-95 Rear Seat Entertainment (RSE) System ...........3-95 Rear Seat Audio (RSA) ................................3-104 Theft-Deterrent Feature ................................3-106 Audio Steering Wheel Controls ......................3-106 Radio Reception .........................................3-108 Rear Side Window Antenna ..........................3-109 XM™ Satellite Radio Antenna System ............3-109 3-2 ✍ NOTES 3-3 Instrument Panel Overview United States version shown; Canada similar. 3-4 A. Air Outlets. See Outlet Adjustment on page 3-31. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7. C. Instrument Panel Cluster. See Instrument Panel Cluster on page 3-34. D. Hazard Warning Flasher Button. See Hazard Warning Flashers on page 3-6. E. Shift Lever and Range Selection Mode. See Automatic Transmission Operation on page 2-30. F. Tow/Haul Selector Button. See Tow/Haul Mode on page 2-34. G. Driver Information Center Controls. See Driver Information Center (DIC) on page 3-48. H. Analog Clock. See Analog Clock on page 3-25. I. Audio System. See Audio System(s) on page 3-70. J. StabiliTrak® Button. See StabiliTrak® System on page 4-6. Rear Park Aid Disable Button. See Ultrasonic Rear Parking Assist (URPA) on page 2-48. L. Exterior Lamps Control. See Exterior Lamps on page 3-16. M. Dome Lamp Override Button. See Dome Lamp Override on page 3-22. Instrument Panel Brightness Control. See Instrument Panel Brightness on page 3-21. Fog Lamp Button. See Fog Lamps on page 3-21. N. Cruise Control Buttons. See Cruise Control on page 3-13. O. Horn. See Horn on page 3-6. P. Audio Steering Wheel Controls. See Audio Steering Wheel Controls on page 3-106. Q. Dual Automatic Climate Controls. See Dual Automatic Climate Control System on page 3-26. R. Pedal Adjust Button. See Adjustable Throttle and Brake Pedal on page 2-28. Heated Windshield Washer Fluid Button. See Windshield Washer on page 3-11. Power Running Boards Disable Button (If Equipped). See Power Running Boards on page 2-17. K. Tilt Wheel Lever. See Tilt Wheel on page 3-6. S. Glove Box. See Glove Box on page 2-60. 3-5 Hazard Warning Flashers The hazard warning ﬂashers warn others. They also let police know you have a problem. Horn To sound the horn, press the center pad on the steering wheel. The hazard warning ﬂasher button is located on top of the steering column. Tilt Wheel Your vehicle has a tilt wheel, that lets you adjust the steering wheel before driving. Raising it to the highest level gives more room to exit and enter your vehicle. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. The hazard warning ﬂashers work no matter what ignition position the key is in, and even if the key is not in the ignition. When the hazard warning ﬂashers are on, your vehicle’s turn signals will not work. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. 3-6 The tilt steering wheel lever is located on the lower left side of the column. To tilt the wheel, hold the steering wheel and pull the lever. Then move the steering wheel to a comfortable position and release the lever to lock the wheel in place. Heated Steering Wheel Your vehicle may have a heated steering wheel. The button with this symbol is located on the left side of the steering wheel. Press the button to turn the heated steering wheel on or off. A light on the button will display when the feature is turned on. The steering wheel will take about three minutes to start heating. Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: (cid:129) G Turn and Lane Change Signals. See Turn and Lane-Change Signals on page 3-8. (cid:129) 53 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 3-9. (cid:129) N Windshield Wipers. See Windshield Wipers on page 3-9. (cid:129) L Windshield Washer. See Windshield Washer on page 3-11. 3-7 (cid:129) 5 Rear Wiper Delay. See Rear Window Wiper/Washer on page 3-12. (cid:129) Z Rear Wiper. See Rear Window Wiper/Washer on page 3-12. (cid:129) = Rear Wiper Wash. See Rear Window Wiper/Washer on page 3-12. Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. To signal a lane change, raise or lower the lever for less than one second until the arrow starts to ﬂash. This will cause the turn signals to automatically ﬂash three times. It will ﬂash six times if tow-haul mode is active. Holding the turn signal lever for more than one second will cause the turn signals to ﬂash until you release the lever. The lever will return by itself when it is released. 3-8 An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. As you signal a turn or a lane change, if the arrows ﬂash more quickly than normal, a signal bulb may be burned out and other drivers will not see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check for burned-out bulbs and a blown fuse. See Fuses and Circuit Breakers on page 5-108. Turn Signal On Chime If your turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each ﬂash of the turn signal and the message TURN SIGNAL ON will also appear in the Driver Information Control (DIC). To turn the chime and message off, move the turn signal lever to the off position. Headlamp High/Low-Beam Changer 53(Headlamp High/Low Beam Changer): To change the headlamps from low to high beam, push the lever toward the instrument panel. To return to low-beam headlamps, pull the multifunction lever toward you. Then release it. When the high beams are on, this indicator light on the instrument panel cluster will also be on. Windshield Wipers Clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, gently loosen or thaw them. Damaged wiper blades may not clear the windshield well, making it harder to see and drive safely. If the blades do become damaged, install new blades or blade inserts. For more information, see Windshield Wiper Blade Replacement on page 5-54. Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Clear away snow or ice to prevent an overload. Turn the band with the wiper symbol to control the windshield wipers. 8 (Mist): Turn the band to mist for a single wiping cycle. Hold it there until the wipers start. Then let go. The wipers stop after one wipe. Hold the band on mist longer, for more wipe cycles. 9 (Off): To stop the wipers, move the band to off. 6 (Delay): Turn the band to adjust the delay time. The delay between wiping cycles becomes shorter as the band is moved to the top of the lever. This can be very useful in light rain or snow. 6 (Low Speed): Turn the band away from you to the ﬁrst solid band past the delay settings, for steady wiping at low speed. ? (High Speed): Turn the band further, to the second solid band past the delay settings, for high-speed wiping. 3-9 Rainsense™ II Wipers Your vehicle has Rainsense™ II windshield wipers. These wipers automatically turn on when a sensor, mounted next to the inside rearview mirror, detects moisture on the windshield. When active, these wipers are able to detect moisture on the windshield and automatically turn on the wipers. To turn on the Rainsense™ feature, the wipers must be set to one of the ﬁve delay settings. Each of the ﬁve settings adjusts the sensitivity of the rain sensor. Since different drivers have different setting preferences, it is recommended that the mid-range setting, position three, be used initially. For more wipes, select the higher settings; for fewer wipes, select the lower settings located closer to the off position on the multifunction lever. The rain sensor will automatically control the frequency of the wipes from off to high speed according to the weather conditions. The wipers can be left in a Rainsense™ mode even when it is not raining. When Rainsense™ II is active, the headlamps will turn on automatically after approximately eight wipes. The headlamps will turn off if the wiper switch is set to a delay position, and there have been no wipes for approximately three minutes, or if the wiper switch is turned to the off position. If it is dark outside, the headlamps will remain on. Notice: Going through an automatic car wash with the wipers on can damage them. Turn the wipers off when going through an automatic car wash. 3-10 Windshield Washer {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. L (Washer Fluid): There is a paddle marked with the windshield washer symbol at the top of the multifunction lever. To spray washer ﬂuid on the windshield, push the paddle. The wipers will clear the window and then either stop or return to your preset speed. Heated Windshield Washer The heated windshield washer ﬂuid system may be used to help clear ice, snow, tree sap, or bugs from your windshield. The button is located in the switchbank under the climate controls. Push the heated washer ﬂuid button while the ignition is turned on to activate the heated windshield washer ﬂuid system. The indicator light will ﬂash. This activation will initiate four heated wash/wipe cycles. The ﬁrst heated wash/wipe cycle may take up to 40 seconds to occur, depending on outside temperature. After the ﬁrst wash/wipe cycle, it may take up to 20 seconds for each of the remaining cycles to begin. Press the button again to turn off the heated windshield washer ﬂuid system or it will automatically turn off after four wash/wipe cycles have been completed. When the heated windshield washer ﬂuid system is activated under certain outside temperature conditions, steam may ﬂow out of the washer nozzles for a short period of time before washer ﬂuid is sprayed. This is a normal condition. 3-11 Z (Rear Wiper): To turn on the rear wiper, slide the lever to this setting. = (Rear Wiper Wash): To turn on the rear wiper wash, push the button on the end of the turn signal/multifunction lever to spray washer ﬂuid on the rear window. The wipers will clear the rear window and either stop or return to your preset speed. For more washer cycles, press and hold the button. The rear window wiper/washer will not operate if the liftgate or liftglass is open or ajar. If the liftgate or liftglass is opened while the rear wiper is on, the wiper will return to the parked position and stop. Rear Window Wiper/Washer {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. The rear wiper control is located on the turn signal/multifunction lever. To turn the rear wiper on, slide the lever to a wiper position. 9(Off): To turn the wiper off, slide the lever to this setting. 5 (Rear Wiper Delay): To turn on the rear wiper delay, slide the lever to this setting. 3-12 Cruise Control {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When you apply your brakes, cruise control is turned off. If your vehicle has the StabiliTrak® system and begins to limit wheel spin while you are using cruise control, the cruise control will automatically disengage. See StabiliTrak® System on page 4-6. When road conditions allow you to safely use it again, you may turn the cruise control back on. The cruise control buttons are located on left side of the steering wheel. T (On/Off): This button can both activate and turn off the system. The indicator light on the button turns on when cruise control is on and turns off when cruise control is off. + RES (Resume/Accelerate): Press this button to make the vehicle accelerate or resume to a previously set speed. SET − (Set/Coast): Press this button to set the speed or make the vehicle decelerate. [ (Cancel): Press this button to cancel cruise control without erasing the set speed from memory. 3-13 Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This shuts off the cruise control. But you do not need to reset it. Once you are driving about 25 mph (40 km/h) or more, press the +RES button on your steering wheel. The vehicle will go back to the previous set speed and stay there. Increasing Speed While Using Cruise Control To increase the cruise speed while using cruise control: (cid:129) Press and hold the +RES button on the steering wheel until you reach your new desired speed, then release it. To increase vehicle speed in small increments, press the +RES button. Each time you do this, you will go about 1 mph (1.6 km/h) faster. Setting Cruise Control Cruise control will not work if your parking brake is set, or if the master cylinder brake ﬂuid level is low. The cruise control light on the instrument panel cluster will come on after the cruise control has been set to the desired speed. {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Press the cruise control On/Off button. 2. Get up to the desired speed. 3. Press the SET− button located on the steering wheel and release it. 4. Take your foot off the accelerator. 3-14 (cid:129) Reducing Speed While Using Cruise Control To reduce your speed while using cruise control: (cid:129) Press and hold the SET– button on the steering wheel until the desired lower speed is reached, then release it. To slow down in very small amounts, press the SET– button on the steering wheel brieﬂy. Each time you do this, the vehicle will go about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the previous set cruise speed. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load, and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain the vehicle’s speed. When going downhill, you may have to brake or shift to a lower gear to keep the vehicle’s speed down. Of course, applying the brake takes you out of cruise control. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control There are three ways to end cruise control: (cid:129) Step lightly on the brake pedal. (cid:129) Press the cancel button on the steering wheel. (cid:129) Press the On/Off button on the steering wheel. Erasing Speed Memory When you turn off the cruise control or the ignition, the cruise control set speed memory is erased. 3-15 (cid:129) Exterior Lamps The exterior lamps control is located on the instrument panel to the left of the steering wheel. It controls the following systems: (cid:129) Headlamps Taillamps (cid:129) Parking Lamps License Plate Lamps Instrument Panel Lights 3-16 The exterior lamps control has four positions: 9 (Off): Turn the control to this position to turn off the automatic headlamps and daytime running lamps (DRL). Turning the headlamp control to the off position again will turn the automatic headlamps or DRL back on. For vehicles ﬁrst sold in Canada, the off position will only work when the vehicle is shifted into the PARK (P) position. AUTO (Automatic): Turn the control to this position to set the headlamps to automatically turn on at normal brightness, together with the following: (cid:129) Parking Lamps Instrument Panel Lights Taillamps License Plate Lamps ;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: Instrument Panel Lights Taillamps License Plate Lamps (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) 2(Headlamps): Turn the control to this position to turn on the headlamps together with the following lamps listed below. When the headlamps are turned on while the vehicle is on, the headlamps will turn off automatically 10 minutes after the ignition is turned off. When the headlamps are turned on while the vehicle is off, the headlamps will stay on for 10 minutes before automatically turning off to prevent the battery from being drained. Turn the headlamp control to off and then back to the headlamp on position to make the headlamps stay on for an additional 10 minutes. (cid:129) Parking Lamps Instrument Panel Lights Taillamps License Plate Lamps IntelliBeam® Intelligent High-Beam Headlamp Control System If your vehicle has this feature, be sure to read this entire section before using it. IntelliBeam® is an enhancement to your vehicle’s headlamp system. Using a digital light sensor on your rearview mirror, this system will turn the vehicle’s high-beam headlamps on and off according to surrounding traffic conditions. The IntelliBeam® system will turn your high-beam headlamps on when it is dark enough, there is no other traffic present, and the IntelliBeam® system is enabled. Turning On and Enabling IntelliBeam® Press and release the IntelliBeam® button on the inside rear view mirror. The IntelliBeam® indicator on the mirror will turn on to let you know the system has been turned on. Once the system has been turned on, it will remain on each time the vehicle is started. Additionally, the IntelliBeam® system must be enabled. To enable the IntelliBeam® system, turn the exterior lamp control to AUTO, with the turn signal/multifunction lever in its neutral position. The High-Beam On Light will appear on the instrument panel cluster when the high-beams are on. See Highbeam On Light on page 3-47. 3-17 (cid:129) (cid:129) (cid:129) Driving with IntelliBeam® IntelliBeam® will only activate your high-beams when driving over 20 mph (32 km/h). The high-beam headlamps will remain on, under the automatic control of IntelliBeam®, until any of the following situations occur: The system detects an approaching vehicle’s headlamps. The system detects a preceding vehicle’s taillamps. The outside light is bright enough that high-beam headlamps are not required. The vehicle’s speed drops below 15 mph (24 km/h). The headlamp stalk is moved forward to the high-beam position. See Headlamp High/Low-Beam Changer on page 3-9. When either of these conditions occur, the IntelliBeam® feature will be disabled and the IntelliBeam® light in the mirror will turn off until the high-beam stalk is returned to the neutral position. If IntelliBeam® was using low-beams prior to this action, the IntelliBeam® feature will be temporarily disabled until the stalk is returned to the neutral position. 3-18 The exterior lamp control is turned to any setting except AUTO. When this occurs, IntelliBeam® will be disabled until the control is turned back to the AUTO position. The IntelliBeam® system is turned off at the inside rearview mirror. IntelliBeam® may not turn off the high-beams if the system cannot detect other vehicle’s lamps because of any of the following: The others vehicle’s lamp(s) are missing, damaged, obstructed from view or otherwise undetected. The other vehicle’s lamp(s) are covered with dirt, snow and/or road spray. The other vehicle’s lamp(s) cannot be detected due to dense exhaust, smoke, fog, snow, road spray, mist or other airborne obstructions. (cid:129) Your vehicle’s windshield is dirty, cracked or obstructed by something that blocks the view of the IntelliBeam light sensor. (cid:129) Your vehicle’s windshield is covered with ice, dirt, haze or other obstructions. (cid:129) Your vehicle is loaded such that the front end of the vehicle points upward, causing the IntelliBeam sensor to aim high and not detect headlamps and taillamps. (cid:129) You are driving on winding or hilly roads. (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) You may need to manually disable or cancel the high-beam headlamps by turning the low-beam headlamps on, if any of the above conditions exist. Disabling and Resetting IntelliBeam® at the Rearview Mirror IntelliBeam® can be disabled by using the controls on the inside rearview mirror. AUTO 3 (On/Off): To disable the system, press this button on the inside rearview mirror. The IntelliBeam® indicator will turn off and will not come back on until the IntelliBeam® button is pressed again. (Stalk Disable): When IntelliBeam® has turned on the high-beams, pull or push the high-beam stalk. This will disable IntelliBeam®. The IntelliBeam® indicator on the mirror will turn off. To re-enable IntelliBeam®, press the IntelliBeam® button on the mirror. A different sensitivity setting is available for dealer diagnostics. This is done by pushing and holding this button for 20 seconds until the IntelliBeam® indicator light ﬂashes three times. If you accidentally activate this, the vehicle’s setting will automatically be reset each time the ignition is turned off and then on again. Cleaning the IntelliBeam® Light Sensor The light sensor is located on the inside of the vehicle in front of the inside rearview mirror. Clean the light sensor window, periodically, using glass cleaner on a soft cloth. Gently wipe the sensor window. Do not spray glass cleaner directly on the surface of the sensor window. Headlamps on Reminder If a door is open, a reminder chime will sound when your headlamps or parking lamps are manually turned on and your key is out of the ignition. To turn off the chime, turn the headlamp switch to off or AUTO and then back on, or close and re-open the door. In the AUTO mode, the headlamps turn off once the ignition is in LOCK or may remain on until the headlamp delay ends (if enabled in the DIC). See “Exit Lighting” under DIC Vehicle Customization on page 3-61. 3-19 Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The DRL system will come on when the following conditions are met: The ignition is on. The exterior lamps control is in AUTO. The transmission is not in PARK (P). The light sensor determines it is daytime. When the DRL are on, only the DRL lamps will be on. The taillamps, sidemarker, and other lamps will not be on. The instrument panel will not be lit up either. When it begins to get dark, the automatic headlamp system will switch from DRL to the headlamps. To turn off the DRL lamps, turn the exterior lamps control to the OFF position and then release. For vehicles ﬁrst sold in Canada, the transmission must be in the PARK (P) position, before the DRL lamps can be turned off. 3-20 Automatic Headlamp System When it is dark enough outside, the automatic headlamp system will turn on the headlamps at the normal brightness, along with the taillamps, sidemarker, parking lamps, and the instrument panel lights. The radio lights will also be dim. To turn off the automatic headlamp system, turn the exterior lamps switch to the off position and then release it. For vehicles ﬁrst sold in Canada, the transmission must be in the PARK (P) position, before the automatic headlamp system can be turned off. The vehicle has a light sensor located on the top of the instrument panel in the defroster grille that regulates when the automatic headlamps turn on. Be sure it is not covered, or the headlamps will come on whenever the ignition is on. The system may also turn on the headlamps when driving through a parking garage, heavy overcast weather, or a tunnel. This is normal. There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor detects a change in lighting lasting longer than the delay. (cid:129) (cid:129) (cid:129) (cid:129) If the vehicle is started in a dark garage, the automatic headlamp system will come on immediately. Once the vehicle leaves the garage, it takes approximately one minute for the automatic headlamp system to change to DRL if it is bright enough outside. During that delay, the instrument panel cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See Instrument Panel Brightness on page 3-21. To idle the vehicle with the automatic headlamp system off, turn the control to the off position. The headlamps will also stay on after you exit the vehicle. This feature can be programmed using the Driver Information Center (DIC). See DIC Vehicle Customization on page 3-61. The regular headlamp system can be turned on when needed. Fog Lamps - (Fog Lamps): If your vehicle has fog lamps, the control is located next to the exterior lamps control on the instrument panel to the left of the steering column. The ignition must be in the ON/RUN position for the fog lamps to come on. Press the button to turn the fog lamps on or off. A light will come on in the instrument panel cluster. When the fog lamps are turned on, the headlamps automatically turn on. When the headlamps are changed to high-beam, the fog lamps also go off. When the high-beam headlamps go off, the fog lamps will come on again. Some localities have laws that require the headlamps to be on along with the fog lamps. Instrument Panel Brightness D(Instrument Panel Brightness): This feature controls the brightness of the instrument panel lights and is located next to the exterior lamp control. Push the knob to extend out and then it can be turned. Turn the knob clockwise or counterclockwise to brighten or dim the instrument panel lights. Turning the knob to the farthest clockwise position turns on the dome lamps. 3-21 Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. The dome lamps can also be turned on by turning the instrument panel brightness knob, located next to the exterior lamps control, clockwise to the farthest position. In this position, the dome lamps remain on whether a door is opened or closed. Dome Lamp Override The dome lamp override button is located next to the exterior lamps control. k (Dome Off): Press the button in and the dome lamps remain off when a door is opened. Press the button again to return it to the extended position so that the dome lamps come on when a door is opened. Entry Lighting Your vehicle has an illuminated entry feature. When the doors are opened, the dome lamps will come on if the dome override button is in the extended position. If the dome override button is pressed in, the lamps will not come on. Exit Lighting The interior lamps come on when the key is removed from the ignition. They turn off automatically in 20 seconds. The lights do not come on if the dome override button is pressed in. Reading Lamps If your vehicle has reading lamps, press the button located next to the lamp to turn it on or off. Your vehicle may also have reading lamps in other locations. To turn each one on or off, press the button located next to the lamp. The lamps cannot be adjusted. 3-22 Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as Battery Saver Active or Service Battery Charging System. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. See DIC Warnings and Messages on page 3-53. Battery Run-Down Protection This feature shuts off the dome lamps if they are left on for more than 10 minutes when the ignition is in LOCK. This will help prevent the battery from running down. 3-23 Accessory Power Outlet(s) The accessory power outlets let you plug in auxiliary electrical equipment, such as a cellular telephone or CB radio. Your vehicle has one accessory power outlet inside the ﬂoor console storage bin, one on the back of the ﬂoor console, and one power outlet in the rear cargo area on the passenger side. To use an accessory power outlet, remove the protective cap. When not in use, always cover the accessory power outlet with the protective cap. Certain power accessory plugs may not be compatible to the accessory power outlet and could result in blown adapter or vehicle fuses. If you experience a problem, see your dealer/retailer for additional information on the accessory power plugs. The accessory power outlets are powered, even when the ignition is in LOCK/OFF. Continuing to use power outlets while the ignition is in LOCK/OFF may cause the vehicle’s battery to run down. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Do not use equipment exceeding the maximum amperage rating of 20 amperes. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Improper use of the power outlet can cause 3-24 If you put papers, pins, or other ﬂammable Ashtray(s) and Cigarette Lighter The front ashtray and cigarette lighter are located in the center console near the cupholders, if the vehicle has them. Press on the access door to open it and use the ashtray and lighter. Notice: items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. To remove the ashtray, pull it from the center console. Slide it back in and push down to be sure it is secure. To use the cigarette lighter, push it in all the way, and let go. When it is ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot. Damage from overheating can occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Analog Clock The analog clock is not connected with any other vehicle system and runs by itself. To adjust the clock, do the following: 1. Locate the adjustment button, near the lower left corner of the clock. 2. Push and hold the adjustment button to advance the clock hands. Holding the button down will cause the clock to advance faster. Release the button before you get to the desired time. 3. Push and release the button to increase the time by one minute increments until the desired time is reached. 3-25 Climate Controls Dual Automatic Climate Control System With this system, you can control the heating, cooling, and ventilation in your vehicle. Your vehicle also has a ﬂow-through ventilation system described later in this section. Climate Control with Cooled and Heated Seats shown You can select different climate control settings for the driver and passengers. 3-26 Driver’s Side Temperature Knob The driver’s side knob is used to adjust the temperature of the air coming through the system on the driver’s side. The temperature can be adjusted even if the system is turned off. This is possible since outside air will always ﬂow through the system as the vehicle is moving forward unless it is set to recirculation mode. See “Recirculation” later in this section. Turn the knob counterclockwise or clockwise to lower or increase the cabin temperature. The display will show the temperature setting decreasing or increasing. Passenger’s Side Temperature Knob The passenger’s side knob can be used to change the temperature of the air coming through the system on the passenger’s side of the vehicle. The temperature can be adjusted even if the system is turned off. This is possible since outside air will always ﬂow through the system as the vehicle is moving forward unless it is set to recirculation mode. See “Recirculation” later in this section. Turn the knob counterclockwise or clockwise to lower or increase the cabin temperature. The display will show the temperature setting decreasing or increasing. Set the passenger’s temperature setting to match the driver’s temperature setting by pressing the passenger power knob. Automatic Operation AUTO (Automatic): When automatic operation is active the system will control the inside temperature, the air delivery, and the fan speed. Use the steps below to place the entire system in automatic mode: 1. Press the AUTO button. When AUTO is selected, the display will change to show the current temperature(s) and AUTO come on the display. The current delivery mode and fan speed will also be displayed for approximately ﬁve seconds. When AUTO is selected, the air conditioning operation and air inlet will be automatically controlled. The air conditioning compressor will run when the outside temperature is over about 40°F (4°C). The air inlet will normally be set to outside air. If it is hot outside, the air inlet may automatically switch to recirculate inside air to help quickly cool down your vehicle. The light on the button will come on in recirculation. 2. Set the driver’s and passenger’s temperature. To ﬁnd your comfort setting, start with a 74°F (23°C) temperature setting and allow about 20 minutes for the system to regulate. Use the driver’s or passenger’s temperature buttons to adjust the temperature setting as necessary. If you choose the temperature setting of 60°F (15°C), the system will remain at the maximum cooling setting. If you choose the temperature setting of 90°F (32°C), the system will remain at the maximum heat setting. Choosing either maximum setting will not cause the vehicle to heat or cool any faster. Be careful not to cover the sensor located on the top of the instrument panel near the windshield. This sensor regulates air temperature based on sun load and also turns on your headlamps. To avoid blowing cold air in cold weather, the system will delay turning on the fan until warm air is available. The length of delay depends on the engine coolant temperature. Pressing the fan switch will override this delay and change the fan to a selected speed. O (Off): Press the driver’s side temperature knob to turn off the climate control system. Outside air will still enter the vehicle, and will be directed to the ﬂoor. This direction can be changed by pressing the mode button. The temperature can also be adjusted using either temperature knob. Press the up or down arrows on the fan switch, the defrost button, the AUTO button, driver’s side temperature knob, or the air conditioning button to turn the system on when it is off. 3-27 Manual Operation You may manually adjust the air delivery mode or fan speed. y9 z (Fan): The switch with the fan symbol allows you to manually adjust the fan speed. Press the up arrow to increase fan speed and the down arrow to decrease fan speed. Pressing this button when the system is off will turn the system on. Pressing either arrow while using automatic operation will place the fan in manual operation. The fan setting will display and the AUTO light will turn off. The air delivery will remain in automatic operation. N (Mode): Press this button to manually change the direction of the airﬂow in your vehicle. Repeatedly press the button until the desired mode appears on the display. When the system is turned off, the display will go blank after displaying the current status of the system. H (Vent): This setting will deliver air to the instrument panel outlets. ) (Bi-Level): This mode allows for split air to the instrument panel outlets and to the ﬂoor outlets. The ﬂow can be divided between vent and ﬂoor outlets depending upon where the knob is placed between the settings. A little air is directed towards the windshield and side window vents. Cooler air is directed to the upper vents and warmer air to the ﬂoor vents. 6 (Floor): This mode directs most of the air to the ﬂoor outlets, with some of the air directed to the windshield, side window outlets, and second row ﬂoor outlets. In this mode, the system will automatically select Outside Air. - (Defog): See “Defogging and Defrosting” later in this section. 3-28 @ (Recirculation): Press this button to turn the recirculation mode on. When the button is pressed, an indicator light will come on. This mode keeps outside air from entering the vehicle. It can be used to reduce outside air and odors from entering your vehicle. Recirculation may also help cool the air inside your vehicle more quickly once the temperature inside the vehicle is less than the outside temperature. The recirculation mode cannot be used with ﬂoor, defrost, or defogging modes. If you try to select recirculation in one of those modes, the indicator will ﬂash three times and turn off. The air conditioning compressor will also come on when this mode is activated. While in recirculation mode the windows may fog when the weather is cold and damp. To clear the fog, select either the blend or defrost mode and increase the fan speed. Recirculation mode can be turned off by pressing the button again, or turning off the engine. Air Conditioning # (Air Conditioning): Press this button to turn the air conditioning (A/C) compressor on and off. When air conditioning is selected, an indicator light will come on to let you know that the air conditioning has been activated.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2008 Cadillac Escalade Premium Owners Manual