2007 Buick Terraza Owners Manual

Download PDF Manual
OnStar® Virtual Advisor Your vehicle may have Virtual Advisor. It is a feature of OnStar® Hands-Free Calling that uses your minutes to access weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. Customize your information proﬁle at www.myonstar.com. See the OnStar® Owner’s Guide for more information. 146 OnStar® Steering Wheel Controls $: Your vehicle may be equipped with a Talk/Mute button that can be used to interact with OnStar®. See Audio Steering Wheel Controls on page 341 for more information. When calling into voice mail systems or to dial directory numbers, press this button once, wait for the response, say the number(s) to be dialed, wait for the number(s) to be repeated and then say “dial.” See the OnStar® Owner’s Guide for more information. Universal Home Remote System Universal Home Remote System (With Three Round LED) The Universal Home Remote System provides a way to replace up to three hand-held Radio-Frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The FCC Grant of Equipment Authorization Certiﬁcate number is KOBGTE05A. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. The Canadian Registration ID number is 3521A-GTE05A. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. 147 Universal Home Remote System (With One Triangular LED) The Universal Home Remote System provides a way to replace up to three hand-held radio-frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The FCC Grant of Equipment Authorization Certiﬁcate number is CB2SAHL3. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. The Canadian Registration ID number is 2791021849A. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. 148 Universal Home Remote System Operation (With Three Round LED) Your vehicle may have the Universal Home Remote System. If there are three round Light Emitting Diode (LED) above the Universal Home Remote System buttons, follow the instructions below. If there is one triangular LED above the Universal Home Remote System buttons, follow the instructions under Universal Home Remote System Operation (with one triangular LED). This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home lighting. Do not use the this system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read the instructions completely before attempting to program the transmitter. Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter. Be sure to keep the original remote control transmitter for use in other vehicles, as well as, for future programming. You only need the original remote control transmitter for ﬁxed code programming. It is also recommended that upon the sale or lease termination of the vehicle, the programmed buttons should be erased for security purposes. See “Erasing your Universal Home Remote Buttons” later in this section. 149 Be sure that people and objects are clear of the garage door or security device you are programming. When programming a garage door, it is advised to park outside of the garage. Programming Universal Home Remote — Fixed Code Fixed Code garage door openers are used for garage doors produced prior to 1996. Fixed code uses the same coded signal every time, which is manually programmed by setting DIP switches for a unique personal code. Follow these steps to program up to three channels: 1. Remove the battery cover of the hand-held transmitter. If you do not know if your garage door opener is a ﬁxed code or rolling code device, open your garage door opener’s remote control battery cover. Your garage door opener is a ﬁxed code device if there is a panel of switches. If not, your garage door opener is a rolling code device. 150 Example of Switch Settings Example 2. Write down the eight to 12 coding switch settings from left to right. When the switch is in the up position, write “on,” and when a switch is in the down position, write “off”. If a switch is set between the up and down position, write “middle”. 3. Enter these positions into the Universal Home Remote System as follows. Press and release all three buttons at the same time to put the device into programming mode. 4. The indicator light will blink slowly. In order from left to right, and within two and one-half minutes, enter each switch setting into the Universal Home Remote System. Push one button for each switch as follows: (cid:127) Left button = “on” switch position. (cid:127) Right button = “off” switch position. (cid:127) Middle button = “middle” switch position. 151 5. After entering the switch settings, press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button you would like to use to control the garage door until the garage door moves. The indicator light above the selected button should slowly blink. You may need to hold the button from ﬁve to 55 seconds. 7. Immediately release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 8. Press and release the button again. The garage door should move, conﬁrming that programming is successful and complete. To program another device such as an additional garage door opener, a security device, or home lighting, repeat Steps 1 through 8, choosing a different function button in Step 7 than what you used for the garage door opener. Programming Universal Home Remote — Rolling Code Rolling code garage door openers are used for garage doors produced after 1996 and are code protected. Rolling code means the coded signal is changed every time your remote control garage door opener is used. Programming a rolling code garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. Follow these steps to program up to three channels: 1. Press the two outside buttons at the same time for one to two seconds, and immediately release them. 152 2. Go to the garage. Locate the garage door motor head and press and release the “learn” button. After pressing the “learn” button, you have 10 to 30 seconds to complete Step 4 depending on your garage control unit. If you cannot locate the “learn” button, refer to the owners guide for your garage door opener. 3. Press and hold the button you would like to use to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. You may need to hold the button from ﬁve to 20 seconds. 4. Immediately release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 5. Press and release the button again. The garage door should move, conﬁrming that programming is successful and complete. To program another device such as an additional garage door opener, a security device, or home lighting, repeat Steps 1 through 6, choosing a different function button in Step 4 than what you used for the garage door opener. Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted. 153 Reprogramming Universal Home Remote Buttons You can reprogram any of the three buttons by repeating the instructions. Erasing Universal Home Remote Buttons You should erase the programmed buttons when you sell the vehicle or terminate your lease. To erase either rolling code or ﬁxed code on the Universal Home Remote device, do the following: 1. Press and hold the two outside buttons at the same time for approximately 20 seconds, until the indicator lights, located directly above the buttons, begin to blink rapidly. 2. Once the indicator lights begin to blink, release both buttons. The codes from all button will be erased. For additional information on Universal Home Remote, see Customer Assistance Offices on page 530. 154 Universal Home Remote System Operation (With One Triangular LED) Your vehicle may have the Universal Home Remote System. If there is one triangular Light Emitting Diode (LED) above the Universal Home Remote buttons, follow the instructions below. If your vehicle has three round LED above the Universal Home Remote buttons, follow the instructions under Universal Home Remote System Operation (with three round LED). Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the programming of your Universal Home Remote Transmitter. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming steps. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section or, for assistance, see Customer Assistance Offices on page 530. Be sure that people and objects are clear of the garage door or gate operator you are programming. When programming a garage door, it is advised to park outside of the garage. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. Programming Universal Home Remote Follow these steps to program up to three channels: 1. Press and hold down the two outside Universal Home Remote buttons, releasing only when the Universal Home Remote indicator light begins to ﬂash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third hand-held transmitter to the remaining two Universal Home Remote buttons. 2. Position the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the desired Universal Home Remote button and the hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 155 4. The indicator light will ﬂash slowly at ﬁrst and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on continuously, programming is complete and your device should activate when the Universal Home Remote button is pressed and released. To program the remaining two Universal Home Remote buttons, begin with Step 2 under “Programming Universal Home Remote.” Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code device, most commonly, a garage door opener. 7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. 8. Return to the vehicle. Firmly press and hold the programmed Universal Home Remote button for two seconds, then release. Repeat the press/hold/release sequence a second time, and depending on the brand of the garage door opener or other rolling code device, repeat this sequence a third time to complete the programming. The Universal Home Remote should now activate the rolling-code device. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming Universal Home Remote.” Do not repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. 156 Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons To erase programming from the three Universal Home Remote buttons do the following: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. Do not hold the two outside buttons for longer than 30 seconds. 2. Release both buttons. The Universal Home Remote is now in the training (learning) mode and can be programmed at any time beginning with Step 2 under “Programming Universal Home Remote” shown earlier in this section. Individual buttons cannot be erased, but they can be reprogrammed. See “Reprogramming a Single Universal Home Remote Button” following this section. 157 Reprogramming a Single Universal Home Remote Button To program a device to Universal Home Remote using a Universal Home Remote button previously trained, follow these steps: 1. Press and hold the desired Universal Home Remote button. Do not release the button. 2. The indicator light will begin to ﬂash after 20 seconds. While still holding the Universal Home Remote button, proceed with Step 2 under “Programming Universal Home Remote” shown earlier in this section. For additional information on Universal Home Remote, see Customer Assistance Offices on page 530. Storage Areas Your vehicle’s large carrying capacity can store many items. If the vehicle has an extended wheelbase, it can carry even larger items. The ﬂoor pins that are used to attach the seats, can be used to secure larger loads. 158 Glove Box If the glove box has a lock, put your key into the lock and turn the key counterclockwise. To open the glove box, pull the latch release. The glove box door has a detent to prevent the door from lowering too far. Open the glove box until the door is partway open, then pull the door down if you need it fully opened. To close the glove box, the door must be pushed up past the detent. To lock the glove box, put your key into the lock and turn the key clockwise. Cupholder(s) There are cupholders located below the center instrument panel switchbank. The cupholders have a rubber liner that can be removed, so that larger cups can ﬁt into the cupholders. You can also remove the liner to clean it. To use the cupholders, pull the tray out. Push the tray back when not in use. Your vehicle may be equipped with cupholders in the second row. Overhead Console (With Rail) If your vehicle is equipped with an overhead console, it may contain the following: (cid:127) Reading lamps. See Front Reading Lamps on page 186 or Rear Reading Lamps on page 186. (cid:127) Switchbank. See Overhead Console Switchbank on page 188. (cid:127) OnStar® System buttons. See OnStar® System on page 145. (cid:127) Universal Home Remote buttons. See Universal Home Remote System (With Three Round LED) on page 147 or Universal Home Remote System (With One Triangular LED) on page 148. See your dealer to purchase additional items for the rail system. Storage Bin Your vehicle may have a storage bin located on the overhead rail that you can use for storage. If your bin is equipped with the ﬁnger size latches do the following: 1. Place the storage bin on to the rails in the desired location. 2. Push ﬁrmly upward on the bin while supporting it with one hand. 3. Push in on the latch and then rotate it 90 degrees. 159 If your bin is equipped with the hand size latches do the following: 1. Place the storage bin on to the rails in the desired location. 2. Push ﬁrmly upward on the bin while supporting it with one hand. 3. The bin will snap into place. 4. To remove the bin, support the bin with one hand while pulling each latch up and away from the bin. 4. Firmly press down making sure the latch is ﬂat with the ribs (A) on the storage bin. 5. Switch hands and repeat Steps 2 through 4 for the latch on the opposite side of the storage bin. 6. Reverse these steps in order to remove the storage bin. 160 The contents of the bin should never weigh more than 1.5 lbs (0.7 kg). Always make sure to close and latch the bin before driving. Overhead Console (Without Rail) If your vehicle has an overhead console without the rail system, it has two reading lights, a courtesy light, and a switchbank. See Overhead Console Switchbank on page 188 for more information. Floor Console Storage Area If your vehicle has a storage compartment located on the front console below the front cupholders. Pull up and then forward on the handle to open the storage compartment. Folding Tray Your vehicle may be equipped with folding convenience trays located between seats. To use each tray lift up on the handle located on its front end, while pulling up on the tray to lock it into place. There are four cupholders on each tray. 161 Luggage Carrier {CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along. This can cause you to lose control. What you are carrying could be violently torn off, and this could cause you or other drivers to have a collision, and of course damage your vehicle. You may be able to carry something like this inside. But, never carry something longer or wider than the luggage carrier on top of your vehicle. If you have the luggage carrier, you can load things on top of your vehicle. Crossrails are not standard on this vehicle and must be purchased at your dealer. Notice: Loading cargo on the luggage carrier that weighs more than 150 lbs (68 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests on the slats as far forward as possible and against the side rails, making sure to fasten it securely. Do not exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 378. To prevent damage or loss of cargo as you are driving, check now and then to make sure the cargo is still securely fastened. 162 Convenience Net (With Rear Convenience Center) Your vehicle may have a convenience net. The convenience net is designed to help keep small loads, from falling out of the vehicle when the liftgate is opened. Install the convenience net at the rear of your vehicle, inside the liftgate. To use the convenience net, do the following: 1. Attach the upper loops to the posts on both sides of the liftgate opening. The label on the net should be in the upper left corner. 2. Attach the lower loops to the tabs at the rear edge of the rear convenience center. When not in use, it is recommended that you take down the convenience net to extend the life of the net and to help retain its elasticity, and to keep the rear exit clear. Convenience Net (Without Rear Convenience Center) Your vehicle may have a convenience net. The convenience net is designed to help keep small loads, like grocery bags, from falling over. Install the convenience net at the rear of your vehicle, inside the liftgate. To use the convenience net, do the following: 1. Attach the upper loops to the posts on both sides of the liftgate opening. The label on the net should be in the upper left corner. 2. Attach the lower hooks to the metal rings on the ﬂoor. 3. Once you have loaded items into the net, stretch the higher side of the net up and over the top of the load to hold it ﬁrmly in place. The convenience net has a maximum capacity of 100 lbs (45 kg). It is not designed to hold larger, heavier loads. Store such loads on the ﬂoor of your vehicle, as far forward as you can. When not in use, it is recommended that you take down the convenience net to extend the life of the net and to help retain its elasticity, and to keep the rear exit clear. 163 Convenience Center {CAUTION: If any removable convenience item is not secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. Your vehicle may have a convenience center. It provides extra storage space for the rear of the vehicle. To open the convenience center, pull up on the door latch located on the front of the cover. The convenience center cover has two automatic prop rods to hold it up and in place. To close the convenience center cover, you must pull one of the prop rod linkages toward you while holding onto the door latch and lower the convenience center cover to close it. Removing the Convenience Center 1. Make sure that all items are off the convenience center and that it is empty. 2. Turn the hand knob, located at the rear of the convenience center, counterclockwise until the knob is loose. 3. Lift up on the hand knob, then grip and pull up on the convenience center to remove it from the vehicle. 164 Replacing the Convenience Center 1. Make sure the third row seat is properly installed in the vehicle. See Third Row Seat on page 21 for more information. If the third row seat is not in the vehicle with the convenience center, the convenience center will not be locked into the correct position in the vehicle. 2. Make sure that the convenience center is empty and closed. 3. Lift the convenience center up and into the rear of the vehicle. 4. Slide the convenience center in and align it to the rear seat. 5. Press down on the front of the convenience center so the center is aligned on the sill mounting bracket. 6. Turn the hand knob clockwise until it is tight. 7. Pull up on the convenience center to make sure it is locked into place. The cover of the convenience center can be left in its upright position while the vehicle is moving. The convenience center and the third row seat both have a maximum weight capacity of 400 lbs (181.6 kg). Notice: Overloading your vehicle may cause damage. Repairs would not be covered by your warranty. Do not overload your vehicle. 165 ✍ NOTES 166 Section 3 Instrument Panel Instrument Panel Overview ........................ 170 Hazard Warning Flashers .......................... 172 Other Warning Devices ............................. 172 Horn .......................................................... 172 Tilt Wheel .................................................. 172 Turn Signal/Multifunction Lever .................. 173 Turn and Lane-Change Signals ................. 173 Headlamp High/Low-Beam Changer .......... 174 Flash-to-Pass ............................................ 174 Windshield Wipers ..................................... 175 Windshield Washer .................................... 175 Rear Window Wiper/Washer ...................... 176 Cruise Control ........................................... 177 Exterior Lamps .......................................... 181 Wiper Activated Headlamps ....................... 182 Headlamps on Reminder ........................... 182 Daytime Running Lamps (DRL)/ Automatic Headlamp System .................. 182 Instrument Panel Brightness ...................... 183 Interior Lamps Control ............................... 184 Dome Lamp .............................................. 184 Entry Lighting ............................................ 184 Delayed Lighting ........................................ 185 Exit Lighting .............................................. 185 Front Reading Lamps ................................ 186 Rear Reading Lamps ................................ 186 Cargo Lamp .............................................. 186 Electric Power Management ...................... 186 Battery Run-Down Protection ..................... 187 Overhead Console Switchbank .................. 188 Ultrasonic Rear Parking Assist (URPA) ........................................ 188 Accessory Power Outlet(s) ........................ 191 Power Outlet 115 Volt Alternating Current .................................................. 192 Cigarette Lighter ........................................ 193 Climate Controls ......................................... 193 Climate Control System ............................. 193 Dual Climate Control System ..................... 197 Outlet Adjustment ...................................... 200 Rear Climate Control System (Option A, Uplevel) ................................ 200 Rear Climate Control System (Option B, Uplevel) ................................ 203 Passenger Compartment Air Filter ............. 205 Warning Lights, Gages, and Indicators ..... 207 Instrument Panel Cluster ........................... 208 Speedometer and Odometer ...................... 209 Trip Odometer ........................................... 209 167 Section 3 Instrument Panel Tachometer ............................................... 209 Safety Belt Reminder Light ........................ 209 Passenger Safety Belt Reminder Light ....... 210 Airbag Readiness Light ............................. 210 Passenger Airbag Status Indicator ............. 211 Charging System Light .............................. 213 Brake System Warning Light ..................... 214 Anti-Lock Brake System Warning Light ...... 215 Traction Control System (TCS) Warning Light ........................................ 216 Engine Coolant Temperature Gage ............ 217 Malfunction Indicator Lamp ........................ 217 Oil Pressure Light ..................................... 220 Security Light ............................................ 221 Cruise Control Light .................................. 221 Highbeam On Light ................................... 221 Fuel Gage ................................................. 222 Low Fuel Warning Light ............................ 222 Driver Information Center (DIC) .................. 223 DIC Operation and Displays ...................... 224 DIC Compass (Uplevel Only) ..................... 228 DIC Warnings and Messages .................... 230 DIC Vehicle Personalization (Uplevel Only) ........................................ 249 168 Audio System(s) ......................................... 258 Setting the Time ........................................ 259 Radio with CD ........................................... 260 Using an MP3 ........................................... 274 XM Radio Messages ................................. 280 Navigation/Radio System ........................... 282 Rear Seat Entertainment System (Option A, Uplevel) ................................ 282 Rear Seat Entertainment System (Option B, Uplevel) ................................ 298 Rear Seat Audio (RSA) Rear Seat Audio (RSA) (Option A, Uplevel) ................................ 314 (Option B, Uplevel) ................................ 316 Mobile Digital Media System ..................... 319 Theft-Deterrent Feature ............................. 340 Audio Steering Wheel Controls .................. 341 Radio Reception ........................................ 342 Care of Your CDs and DVDs .................... 343 Care of the CD and DVD Player ............... 343 Fixed Mast Antenna .................................. 344 XM™ Satellite Radio Antenna System ....... 344 Chime Level Adjustment ............................ 344 ✍ NOTES 169 Instrument Panel Overview 170 The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 200. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 173. C. Audio Steering Wheel Controls (If Equipped). See Audio Steering Wheel Controls on page 341. D. Instrument Panel Cluster. See Instrument Panel Cluster on page 208. E. Driver Information Center (DIC) Controls (If Equipped). See Driver Information Center (DIC) on page 223. F. Traction Control System Button (If Equipped). See Traction Control System (TCS) on page 353. G. Hazard Warning Flasher Switch. See Hazard Warning Flashers on page 172. H. Passenger Airbag Status And Passenger Seatbelt Reminder Indicator. See Passenger Airbag Status Indicator on page 211 and Passenger Safety Belt Reminder Light on page 210. I. Audio System. See Audio System(s) on page 258. J. Exterior Lamps Control. See Exterior Lamps on page 181. K. Interior Lamps Control. See Interior Lamps Control on page 184. Instrument Panel Brightness Control. See Instrument Panel Brightness on page 183. L. Hood Release. See Hood Release on page 409. M. Parking Brake. See Parking Brake on page 137. N. Horn. See Horn on page 172. O. Cruise Controls (If Equipped). See Cruise Control on page 177. P. Dual Climate Controls. See Dual Climate Control System on page 197. Q. Heated Seat Controls (If Equipped). See Heated Seats on page 10. R. Glove Box. See Glove Box on page 158. 171 Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. Horn Press near or on the horn symbols on your steering wheel pad to sound the horn. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can raise the steering wheel to the highest level to give your legs more room when you enter and exit the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column. To tilt the wheel, hold the wheel and pull the lever. Then move the wheel to a comfortable position and release the lever to lock the wheel in place. The hazard warning ﬂasher button is located in the center of the instrument panel. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key is not in the ignition switch. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals will not work. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. 172 Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane Change Signals. See Turn and Lane-Change Signals on page 173. (cid:127) 53 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 174. (cid:127) Flash-to-Pass. See Flash-to-Pass on page 174. (cid:127) N Windshield Wipers. See Windshield Wipers on page 175. (cid:127) L Windshield Washer. See Windshield Washer on page 175. (cid:127) Z Rear Window Wiper. See Windshield Washer on page 175. (cid:127) = Rear Window Washer. See Windshield Washer on page 175. For information on the headlamps, see Exterior Lamps on page 181. Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever will return automatically. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change. 173 To signal a lane change, just raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever will return by itself when you release it. As you signal a turn or a lane change, if the arrow ﬂashes faster than normal, a signal bulb may be burned out and other drivers will not see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check for burned-out bulbs and check the fuse. See Bulb Replacement on page 443 and Fuses and Circuit Breakers on page 497. If you have a trailer towing option with added wiring for the trailer lamps, the signal indicator will ﬂash at a normal rate even if a turn signal bulb is burned out. Check the front and rear turn signal lamps regularly to make sure they are working. Turn Signal On Chime If either turn signal is left on for more than 3/4 mile (1.2 km), a chime will sound to let the driver know to turn it off. If you need to leave the signal on for more than 3/4 mile (1.2 km), turn off the signal and then turn it back on. 174 Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever away from you. When the high beams are on, this light will appear on the instrument panel cluster. To change the headlamps from high beam to low beam, pull the turn signal/multifunction lever toward you. Flash-to-Pass When the headlamps are off, pull the lever toward you to momentarily turn on the high beams. This will signal that you are going to pass. When you release the lever, they will turn off. Windshield Wipers You control the windshield wipers by turning the band with the wiper symbol on it. 8(Mist): For a single wiping cycle, turn the band to mist. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer. 9(Off): To stop the wipers, move the band to off. N(Delay): You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow. Turn the band to choose the delay time. The closer to the top of the lever, the shorter the delay. 6 (Low Speed): For steady wiping at low speed, turn the band away from you to the ﬁrst solid band past the delay settings. For high-speed wiping, turn the band further, to the second solid band past the delay settings. To stop the wipers, move the band to off. 1 (High Speed): For high-speed wiping, turn the band further, to the second solid band past the delay settings. Be sure to clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, carefully loosen or thaw them. If your blades do become worn or damaged, get new blades or blade inserts. Windshield Washer LQ(Windshield Washer): Press and hold the windshield washer paddle with this symbol on it to wash your windshield. The washers and wipers will operate. When you release the paddle, the washers will stop, and the wipers will continue to operate for two cycles, unless your wipers had already been on. In that case, the wipers will resume the wiper speed you had selected earlier. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. 175 Rear Window Wiper/Washer {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. The controls for the rear window washer/wiper are located on the end of the turn signal/multifunction lever. 9(Off): Move the lever to this position to turn the rear washers/wipers off. Z (Rear Wiper): Move the lever to this position to turn the rear wipers on. =(Rear Washer/Wiper): Move the lever to this position to wash and wipe the rear window. The rear window washer uses the same ﬂuid bottle as the windshield washer. However, the rear window washer will run out of ﬂuid before the windshield washer. If you can wash your windshield but not your rear window, check the ﬂuid level. 176 Cruise Control {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. The cruise control lever is located below the windshield wiper control on the right side of the steering wheel. Q RES + (Resume/Accelerate): Push the lever up to resume the cruise control speed, or to accelerate when passing another vehicle. J(CRUISE CONTROL) ON/OFF q: Press the button on the end of the lever to turn the cruise control on. Press it again to turn cruise control off. R SET — (Set/Coast/Decelerate): Push the lever down to set the cruise speed. If the cruise speed is already set this position can be used to coast or decelerate from a higher speed. CANCEL R: Pull the lever to cancel the cruise control speed. 177 Cruise control allows a speed of approximately 25 mph (40 km/h) or more to be maintained without keeping your foot on the accelerator. This is helpful on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When the brakes are applied, the cruise control shuts off. If the vehicle is in cruise control and the Traction Control System (TCS) begins to limit wheel spin, the cruise control will automatically disengage. See Traction Control System (TCS) on page 353. When road conditions allow, the cruise control can be used again. Setting Cruise Control {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Push the button at the end of the cruise control lever to turn the cruise control on. 2. Accelerate to the desired speed. 3. Push down on the cruise control lever and release it. This will set the speed in cruise control. 4. Remove your foot from the accelerator pedal. This symbol will appear on the instrument panel cluster when the cruise control is set. 178 This symbol will disappear when the brakes are applied or the cruise control is cancelled. It will reappear when the set cruise speed is resumed. Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied, the cruise control shuts off. But the cruise control does not need to be reset. Once the vehicle is traveling approximately 25 mph (40 km/h) or more, the cruise control lever can be pushed upward toward the plus (resume/accelerate) position to return to the preset cruise speed. The vehicle will return to and stay at the preset cruise speed. If the cruise control lever is pushed up and held toward the plus (resume/accelerate) position, the vehicle speed will increase until the lever is released or the brakes are applied. Do not continue to hold the lever in the plus (resume/accelerate) position, unless a faster speed is desired. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: (cid:127) Use the accelerator pedal to get to the higher speed. Push up on the cruise control lever toward the plus (resume/accelerate) position, then release the lever and take your foot off the accelerator pedal. The vehicle will now cruise at the higher speed. (cid:127) Push up and hold the cruise control lever toward the plus (resume/accelerate) position until the vehicle reaches the desired speed. Then release the cruise control lever. To increase the vehicle’s speed in very small amounts, push up brieﬂy on the cruise control lever and release it. Each time this is done, the vehicle will speed up approximately one mph (1.6 km/h). The acceleration feature will only work after the cruise control speed has been set by pushing the cruise control lever down to the set position. 179 Reducing Speed While Using Cruise Control There are two ways to reduce the vehicle’s speed while using cruise control: (cid:127) Push the cruise control lever downward toward the minus (set/coast/decelerate) position until a lower speed is reached, then release it. (cid:127) To slow down in very small amounts, push the cruise control lever downward toward the minus (set/coast/decelerate) position brieﬂy. Each time this is done, the vehicle will slow down approximately one mph (1.6 km/h). Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle’s speed. When you take your foot off the pedal, the vehicle will slow down to the cruise control speed set earlier. Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle’s speed, its load, and the steepness of the hills. When going up steep hills, the accelerator pedal might have to be used in order to maintain the vehicle’s speed. 180 When going downhill, the brakes might have to be applied, or the transaxle might have to be shifted to a lower gear to keep the vehicle’s speed down. Doing either of these things will take the vehicle out of cruise. It may be better not to use the cruise control if the brakes constantly have to be applied, or the vehicle continuously needs to be shifted to a lower gear. Cancelling Cruise Control To cancel a cruise control session, pull the cruise control lever forward, or step lightly on the brake pedal. Doing either of these things will only end the current cruise control session, but the set speed will be retained in memory. Push the button at the end of the cruise control lever to turn the system off. Erasing Speed Memory When the cruise control or the ignition is turned off, the cruise control set speed memory is erased. Exterior Lamps The control to the left of the steering column operates the exterior lamps. 9(Off): Turn the control to this position to toggle off all lamps. This is a momentary control that will spring back to AUTO when released. This momentary control will turn the automatic headlamps and/or the Daytime Running Lamps on and off for U.S. vehicles. For vehicles ﬁrst sold in Canada, this is only true when the transaxle is in PARK (P). AUTO (Automatic): Turn the control to this position to set your headlamps in automatic mode. AUTO mode, if enabled, will turn the exterior lamps on and off automatically depending on how much light is available outside the vehicle. Due to the momentary switch design, your automatic lights may be disabled even if the control is in the AUTO position. ;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: (cid:127) Taillamps (cid:127) 5(Headlamps): Turn the control to this position to turn on the headlamps, together with the previously listed lamps and lights. Instrument Panel Lights 181 Wiper Activated Headlamps This feature, if equipped, will automatically activate the headlamps and parking lamps after the windshield wipers have been in use for about 30 seconds and when all of the following conditions are met. (cid:127) The exterior lamp control is in AUTO. (cid:127) The headlamps have not already been activated by automatic lighting. (cid:127) The automatic lighting feature has not been disabled using the exterior lamp control. See Exterior Lamps on page 181 for additional information. If the wipers are activated for over 30 seconds and the exterior lamp control is in the parking lamps position, or the automatic lighting feature has been disabled using the exterior lamp control, a HEADLAMPS SUGGESTED message will appear on the Driver Information Center, if equipped. Headlamps on Reminder If you turn the ignition to LOCK while leaving the lamps on, you will hear a warning chime once the driver’s door is opened. Daytime Running Lamps (DRL)/ Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional Daytime Running Lamps are required on all vehicles ﬁrst sold in Canada. A light sensor on top of the instrument panel makes the DRL work, so be sure it is not covered. The DRL system will make front parking and turn signal lamps come on in daylight when the following conditions are met: (cid:127) The ignition is on. (cid:127) The exterior lamps control is off. 182 Instrument Panel Brightness The knob to adjust the instrument panel brightness is located in the center of the interior lamp controls. Turn the knob clockwise to brighten the lights and counterclockwise to dim them. When the DRL are on, only your front turn signal lamps will be on. Your instrument panel will not be lit up. When it is dark enough outside, the exterior lamps will come on automatically. When it is bright enough outside, the exterior lamps will turn off and the DRL will turn on. Of course, you may still turn on the headlamps any time you need to. If you start your vehicle in a dark garage, the automatic headlamp system will come on immediately. Once you leave the garage, it will take approximately 30 seconds for the automatic headlamp system to change to DRL if it is light outside. During that delay, your instrument panel cluster may not be as bright as usual. Make sure your instrument panel brightness control is in the full bright position. See Instrument Panel Brightness on page 183. To idle your vehicle with the DRL and automatic headlamps off, toggle the exterior lamp control to off after starting the vehicle. As with any vehicle, you should turn on the regular headlamp system when you need it. 183 Interior Lamps Control The interior lamp control is located to the right of the exterior lamp controls on the instrument panel to the left of the steering column. R(Interior Lamp Override): Turn the outer knob to this position to have your interior lamps remain off while any door is open. 1(Door): Turn the outer knob to this position to turn the interior lamps on while any door is open and when the ignition key is removed from the ignition. +(Interior Lamps): Turn the outer knob to this position to turn the interior lamps on. Turn the inner knob to adjust the instrument panel brightness, described earlier in this section. 184 Dome Lamp The dome lamp is located in the headliner and has two buttons to manually turn it on or off. The dome lamp will come on each time you open a door, unless you turn on the interior lamps override feature. See Interior Lamps Control on page 184. Entry Lighting With entry lighting, the interior of your vehicle is illuminated so that you can see inside before you enter your vehicle. The lamps will come on for 20 seconds if you unlock your door using your key or the remote keyless entry transmitter and the ignition is in LOCK. After 20 seconds have passed, the interior lamps will slowly fade out. The lamps will turn off before the 20 seconds if you do one of the following: (cid:127) Lock all the doors using the key. (cid:127) Press lock on the power door lock switch. (cid:127) Press lock on the remote keyless entry transmitter. When any door is opened, entry lighting is cancelled. The interior lamps will stay on while any door or the liftgate is open, and slowly fade out when all doors and the liftgate are closed. The interior lamps may stay on for up to 25 seconds after all doors have been closed if they have not been locked. See Delayed Lighting on page 185. To turn the entry lighting feature off or on, see DIC Vehicle Personalization (Uplevel Only) on page 249. Delayed Lighting The delayed lighting feature will continue to illuminate the interior for 20 seconds after all doors have been closed, so that you can ﬁnd your ignition and buckle your safety belt at night. Delayed lighting will not occur while the ignition is in RUN or ACCESSORY. After 20 seconds have passed, the interior lamps will slowly fade out. The lamps will fade out before the 20 seconds have passed if you do one of the following: (cid:127) Turn the ignition to RUN or ACCESSORY. (cid:127) Lock all doors using the remote keyless entry transmitter. (cid:127) Lock all doors using the power door lock switch or the key. Exit Lighting With exit lighting, the interior lamps will come on for about 25 seconds whenever you remove the key from the ignition. If you turn the ignition key to RUN or ACCESSORY, the lamps will fade out. The lamps will also fade out if you lock the doors with the power door lock switch or the remote keyless entry transmitter. When any door is opened, exit lighting is cancelled. The interior lamps will stay on while any door or the liftgate is open, and slowly fade out when all doors and the liftgate are closed. The interior lamps may stay on for up to 20 seconds after all doors have been closed if they have not been locked. See Delayed Lighting on page 185. To turn the exit lighting feature off or on, see DIC Vehicle Personalization (Uplevel Only) on page 249. To turn the delayed lighting feature off or on, see DIC Vehicle Personalization (Uplevel Only) on page 249. 185 Front Reading Lamps There are two reading lamps and one courtesy lamp in the overhead console. To turn either reading lamp on or off, press the lens of the lamp. The courtesy lamp will come on each time you open a door, unless you turn on the interior lamps override feature. See Interior Lamps Control on page 184. Rear Reading Lamps There are two reading lamps in the third row headliner. To turn either reading lamp on or off, press the lens of the lamp. There may also be a reading lamp in the second row, integrated with the dome lamp. To turn the second row reading lamp on or off, press the button next to the lamp lens. Cargo Lamp The cargo lamp is located in the rear of your vehicle, above the liftgate opening, and does not have a switch. The cargo lamp will come on each time you open a door, unless you turn on the interior lamps override. See Interior Lamps Control on page 184. Electric Power Management This vehicle has Electric Power Management (EPM), an advanced control system. It estimates the battery’s temperature and state of charge and then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage, you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. 186 The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as Battery Saver Active or Battery Voltage Low. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. Battery Run-Down Protection Your vehicle has a feature to help prevent you from draining the battery, in case you accidentally leave the interior lamps on. If you leave any interior lamps on while the ignition is in lock or off, they will automatically turn off after 10 minutes. The lamps will not come back on again until you do one of the following: (cid:127) Turn the ignition to RUN or ACCESSORY (cid:127) Open a closed door, or close and reopen a door. (cid:127) Turn the interior lamps on if they are in the door or override position. (cid:127) Turn the interior lamps to the door or override position and then to on again if the interior lamp control is in the on position. If your vehicle has less than 15 miles (25 km) on the odometer, the battery saver will turn off the lamps after only three minutes. 187 Overhead Console Switchbank The overhead console switchbank is located in the overhead console. This switchbank may include the following: (cid:127) Power Sliding Door(s)/Override Switch(es). See Power Sliding Door (PSD) on page 112. (cid:127) Power Rear Quarter Windows. See Power Rear Quarter Windows on page 123. (cid:127) Ultrasonic Rear Parking Assist (URPA) Disable Switch. See Ultrasonic Rear Parking Assist (URPA) on page 188. If your vehicle does not have some of these options, there will be a blank. 188 Ultrasonic Rear Parking Assist (URPA) If your vehicle is equipped with the Ultrasonic Rear Parking Assist (URPA) system, it is designed to help you park, while the vehicle is in REVERSE (R). It operates only at very low speeds, less than 3 mph (5 km/h). URPA can help make parking easier and to help you avoid colliding with objects such as parked vehicles. The URPA system can detect objects up to 5 feet (1.5 m) behind the vehicle, and tell you how close these objects are from your rear bumper. Your vehicle’s URPA operates when the shift lever is moved into REVERSE (R) and the vehicle speed is less than 3 mph (5 km/h). Four ultrasonic sensors located at the rear bumper are used to detect the distance to the object. The URPA display is located inside the vehicle, near the rear window. It has three color-coded lights used to provide distance and system information to the driver. {CAUTION: The Ultrasonic Rear Park Assist (URPA) system does not replace driver vision. URPA does not: (cid:127) Operate above speeds of 3 mph (5 km/h). (cid:127) Detect objects more than 5 feet (1.5 meters) behind the vehicle. This distance may be less during warmer or humid weather. (cid:127) Detect objects that are below the bumper, underneath the vehicle, or that are very close to the vehicle. (cid:127) Detect children, pedestrians, bicyclists, or pets. So if you do not use proper care before backing up, you could hit a vehicle, child, pedestrian, bicyclist, or pet, resulting in vehicle damage, injury, or death. Even though the vehicle has the URPA system, always check carefully before backing up by checking behind your vehicle. URPA can be turned off by pressing the rear park aid disable switch located in the overhead console switchbank. While the system is disabled, an indicator light will be lit on the switch. You will not see any lights on the rear display if the switch is in the off position. 189 How the System Works Unless disabled, the URPA will turn on automatically when the shift lever is moved into REVERSE (R). When the system turns on, the three lights on the display will illuminate for one and a half seconds to let you know that the system is working. If your vehicle is moving in REVERSE (R) at a speed greater than 3 mph (5 km/h), the red light will ﬂash to remind you that the system does not work at speed greater than 3 mph (5 km/h). If an object is detected at a REVERSE (R) speed of less than 3 mph (5 km/h), one of the following will occur: Description amber light amber/amber lights amber/amber/red lights & continuous chime amber/amber/ red lights ﬂashing & continuous chime English 5 ft 40 in 20 in 1 ft Metric 1.5 m 1.0 m 0.5 m 0.3 m A chime will sound the ﬁrst time an object is detected between 20 inches (0.5 m) and 5 feet (1.5 m) away. 190 URPA cannot detect objects that are above liftgate level. In order for the rear sensors to recognize an object, it must be within detection range behind the vehicle. When the System Does Not Seem to Work Properly The light may ﬂash red when the vehicle is in REVERSE (R) if the ultrasonic sensors are not kept clean. So be sure to keep your rear bumper free of mud, dirt, snow, ice and slush. Other conditions that may affect system performance include things like the vibrations from a jackhammer or the compression of air brakes on a very large truck. If after cleaning the rear bumper and then driving forward at least 15 mph (25 km/h), the display continues to ﬂash red, see your dealer. If a trailer was attached to your vehicle, or a bicycle or an object was on the back of, or hanging out of your liftgate during your last drive cycle, the light may also ﬂash red. The light will continue to ﬂash whenever in REVERSE (R) until your vehicle is driven forward at least 15 mph (25 km/h) without any obstructions behind the vehicle. Accessory Power Outlet(s) Your vehicle may be equipped with a front accessory power outlet located below the climate controls on the instrument panel. It can be used to plug in electrical equipment such as a cellular telephone or CB radio. Pull the cover down to use the accessory power outlet. When not in use, keep the cover on. The rear accessory power outlet is located on the rear compartment on the driver’s side. To remove the cover, pull the tab on the cover and pull it off. To put the cover back on, line up the tabs at the back of the cover and put the cover in place. Push down the tab to secure the cover. When not in use, always cover the rear accessory power outlet with the protective cap. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating of 20 amperes. Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem see your dealer for additional information on accessory power outlets. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. 191 Power Outlet 115 Volt Alternating Current Your vehicle may have a power outlet that can be used to plug in auxiliary electrical equipment with a maximum limit of 150 watts. If you try to use equipment that requires more than the limit, a protection circuit will cut the power supply. To reset the outlet, unplug the item and plug it back in or turn the ignition to LOCK or ACCESSORY and then back on. The power will automatically restart when equipment that operates within the limit is plugged in. The power outlet is located behind the third row seats on the passenger’s side rear quarter trim panel. The power outlet is not designed for the following electrical equipment and may not work properly if these items are plugged into the power outlet: (cid:127) Equipment with high initial peak wattage such as: compressor-driven refrigerators and electric power tools. (cid:127) Other equipment requiring an extremely stable power supply such as: microcomputer-controlled electric blankets, touch sensor lamps, etc. 192 Climate Controls Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. Cigarette Lighter Your vehicle may have a cigarette lighter. To use the lighter, located on the instrument panel below the climate controls, push it in all the way and let go. When it is ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating. Notice: ﬂammable items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put ﬂammable items in the ashtray. If you put papers, pins, or other Operation Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of your vehicle. 193 To change the current mode, select one of the following: H(Vent): This mode directs air to the instrument panel outlets. )(Bi-Level): This mode directs half of the air to the instrument panel outlets, then directs the remaining air to the ﬂoor outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. 6(Floor): This mode directs most of the air to the ﬂoor outlets. Use this mode to send air to the rear of the vehicle. Keep the area under the front seats free of objects that could obstruct airﬂow to the rear of the vehicle. The right knob can also be used to select defog or defrost mode. For more information, see “Defogging and Defrosting” later in this section. Outside Air: This mode will be automatically selected when your vehicle is in any mode except maximum air conditioning. A (Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob to 0 to turn off the fan. The fan must be turned on for the air conditioning compressor to operate. Temperature Control: Turn the center knob clockwise or counterclockwise to increase or decrease the air temperature inside your vehicle. #(Air Conditioning): Press this button to turn the air-conditioning system on or off. When it is pressed, an indicator light in the button will come on to let you know that air conditioning is activated. You may notice a slight change in engine performance when the air conditioning compressor shuts off and turns on again. This is normal. The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature. On hot days, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for your vehicle to cool down. It also helps the system to operate more efficiently. 194 The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. @ MAX A/C (Maximum Air Conditioning): Turn the right knob to this position for maximum air conditioning. This will select air conditioning and recirculation for maximum cooling of your vehicle. This mode directs air to the instrument panel outlets. Recirculation: This mode keeps outside air from coming in the vehicle. It can be used to prevent outside air and odors from entering your vehicle or help heat or cool the air inside your vehicle more quickly. This mode will automatically be selected when you select maximum air conditioning. ((Heated Seats): Press this button to turn on the heated seats. The button on the left controls the driver’s seat and the button on the right controls the passenger’s seat. See Heated Seats on page 10 for additional information. Defogging and Defrosting Fog on the inside of windows is a result of high humidity, or moisture, condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. Turn the right knob to select the defog or defrost mode. -(Defog): This mode directs air to the windshield and the ﬂoor outlets. When you select this mode, the system runs the air-conditioning compressor unless the outside temperature is at or below freezing. The recirculation mode cannot be selected while in the defog mode. 195 0(Defrost): This mode directs most of the air to the windshield and the side window outlets, with some air directed to the ﬂoor outlets. In this mode, the system will automatically run the air-conditioning compressor, unless the outside temperature is at or below freezing. Recirculation cannot be selected while in the defrost mode. Do not drive the vehicle until all the windows are clear. Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. < REAR: Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated. The rear window defogger will turn off about 10 minutes after the button is pressed. If turned on again, the defogger will only run for about ﬁve minutes before turning off. The defogger can also be turned off by pressing the button again or by turning off the engine. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid. 196 Dual Climate Control System Your vehicle may have a dual climate control system. With this system you can control the heating, cooling, and ventilation for your vehicle. Operation 9(Fan): Turn the left knob clockwise or counterclockwise to increase or decrease the fan speed. Turn the knob to 0 to turn off the fan. The fan must be turned on for the air conditioning compressor to operate. Temperature Control: Use the driver’s and passenger’s levers to increase or decrease the air temperature inside your vehicle. Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of your vehicle. To change the current mode, select one of the following: @ MAX A/C (Maximum Air Conditioning): Turn the right knob to this position for maximum air conditioning. This will select air conditioning and recirculation for maximum cooling of your vehicle. Recirculation: This mode keeps outside air from coming in the vehicle. It can be used to prevent outside air and odors from entering your vehicle or help heat or cool the air inside your vehicle more quickly. This mode will automatically be selected when maximum air conditioning is selected. H(Vent): This mode directs air to the instrument panel outlets. 197 )(Bi-Level): This mode directs half of the air to the instrument panel outlets, then directs the remaining air to the ﬂoor outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. 6(Floor): This mode directs most of the air to the ﬂoor outlets. Use this mode to send air to the rear of the vehicle. Keep the area under the front seats free of objects that could obstruct airﬂow to the rear of the vehicle. Outside Air: This mode is automatically selected when your vehicle is in any mode except maximum air conditioning. The right knob can also be used to select defog or defrost mode. For more information, see “Defogging and Defrosting” later in this section. #(Air Conditioning): Press this button to turn the air conditioning system on or off. When it is pressed, an indicator light in the button will come on to let you know that air conditioning is activated. You may notice a slight change in engine performance when the air conditioning compressor shuts off and turns on again. This is normal. The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature. On hot days, open the windows to let hot inside air escape; then close them and switch to maximum air conditioning mode. This helps to reduce the time it takes for your vehicle to cool down. It also helps the system to operate more efficiently. The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. ((Heated Seats): Press this button to turn on the heated seats. The button on the left controls the driver’s seat and the button on the right controls the passenger’s seat. See Heated Seats on page 10 for additional information. 198 Defogging and Defrosting Fog on the inside of windows is a result of high humidity, or moisture, condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. Turn the right knob to select the defog or defrost mode. -(Defog): This mode directs air to the windshield and the ﬂoor outlets. When this mode is selected, the system runs the air conditioning compressor unless the outside temperature is at or below freezing. The recirculation mode cannot be selected while in the defog mode. 0(Defrost): This mode directs most of the air to the windshield and the side window outlets, with some air directed to the ﬂoor outlets. In this mode, the system will automatically run the air conditioning compressor, unless the outside temperature is at or below freezing. Recirculation cannot be selected while in the defrost mode. Do not drive the vehicle until all the windows are clear. Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. <(Rear Window Defogger): Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated. The rear window defogger will turn off about 10 minutes after the button is pressed. If turned on again, the defogger will only run for about ﬁve minutes before turning off. The defogger can also be turned off by pressing the button again or by turning off the engine. Notice: Do not use anything sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs would not be covered by your warranty. Do not attach a temporary vehicle license, tape, a decal or anything similar to the defogger grid. 199 Outlet Adjustment k(Open): Turn the thumbwheel to this position to open the air outlets. l(Closed): Turn the thumbwheel to this position to close the air outlets. Use the louvers located on the air outlets to change the direction of the airﬂow. Operation Tips (cid:127) Clear away any ice, snow, or leaves from the air inlets at the base of the vehicle that may block the ﬂow of air into your vehicle. (cid:127) Use of non-GM approved hood deﬂectors may adversely affect the performance of the system. (cid:127) Keep the path under the front seats clear of objects to help circulate the air inside of your vehicle more effectively. 200 Rear Climate Control System (Option A, Uplevel) Your vehicle may have a rear climate control system that allows the driver to adjust the fan speed for the rear seating area. This system works with the main climate control system in your vehicle. This lever is located below the main climate control system on the instrument panel. Use this lever to adjust the fan speed for the rear seat passengers. A (Fan): Slide the lever to 1, 2, or 3 to increase or decrease airﬂow to the rear seating area. Slide the fan knob to 0 to turn the fan off. AUX: Slide the lever to AUX to allow the rear passengers to adjust the temperature and airﬂow to the rear seating area. Your vehicle may also have a rear climate control system that allows the rear passengers to adjust the temperature and fan speed for the rear seating area. When the front climate control is in AUX and the rear climate control fan or temperature button is pressed, the display will show the same airﬂow modes as the front climate control system. See Dual Climate Control System on page 197 The front control must be in AUX position to enable adjustment of the temperature and fan speed on the rear control system. If it is not in AUX, pressing the fan or temperature button on the rear climate control will show a DISABLED message on the rear seat entertainment system display. t r(Decrease Setting): Press this button to decrease the fan or temperature setting when arrows are active in the display. 201 Rear Air Outlets The outlet behind the left rear seat is the cold air return outlet. Be sure to keep it free from obstructions. Also, keep the area around the base of the center instrument panel console, between and under the front seats, free of objects that could also obstruct airﬂow to the rear seating area. For more information on how to use the main climate control system, see Dual Climate Control System on page 197. For information on ventilation, see Outlet Adjustment on page 200. [ u(Increase Setting): Press this button to increase the fan or temperature setting when arrows are active in display. 9(Fan): Press this button to increase or decrease fan speed. After pressing this button, arrows and a fan will appear in the display. The arrows indicate that to increase or decrease fan speed, you need to press either the left or right arrow button. The displayed arrows and fan will disappear after a few seconds. b(Temperature): Press this button to increase or decrease temperature. After pressing this button, arrows and a temperature scale will appear in the display. The arrows indicate that to increase or decrease temperature, you need to press either the left or right arrow button. The displayed arrows and temperature scale will disappear after a few seconds. 202 Rear Climate Control System (Option B, Uplevel) Your vehicle may have a rear climate control system that allows the driver to adjust the fan speed for the rear seating area. This system works with the main climate control system in your vehicle. A (Fan): Slide the lever to 1, 2, or 3 to increase or decrease airﬂow to the rear seating area. Slide the fan knob to 0 to turn the fan off. AUX: Slide the lever to AUX to allow the rear passengers to adjust the temperature and airﬂow to the rear seating area. Your vehicle may also have a rear climate control system that allows the rear passengers to adjust the temperature and fan speed for the rear seating area. When the front climate control is in AUX and the rear climate control fan or temperature button is pressed, the display will show the same airﬂow modes as the front climate control system. See Dual Climate Control System on page 197 This lever is located below the main climate control system on the instrument panel. Use this lever to adjust the fan speed for the rear seat passengers. 203 9(Fan)b(Temperature): Press this button once to enable adjustment of the fan speed. After pressing this button, the current fan speed setting will be highlighted and appear in the on screen display. The arrows indicate that to increase or decrease fan speed, you need to press either the left or right arrow button. The on screen display will disappear after a few seconds. Press this button twice to enable temperature adjustment. After pressing this button, the current temperature settings will be highlighted and appear in the on screen display. The arrows indicate that to increase or decrease temperature, you need to press either the left or right arrow button. The on screen display will disappear after a few seconds. Pressing this button a third time will turn off the on screen display. QR: Press the up and down arrows to toggle between the fan and temperature settings. The front control must be in AUX position to enable adjustment of the temperature and fan speed on the rear control system. If it is not in AUX, pressing the fan or temperature button on the rear climate control will show a DISABLED message on the rear seat entertainment system display. q g (Decrease Setting): Press this button to decrease the fan or temperature setting when arrows are active in the display. r l (Increase Setting): Press this button to increase the fan or temperature setting when arrows are active in the display. 204 Rear Air Outlets The outlet behind the left rear seat is the cold air return outlet. Be sure to keep it free from obstructions. Also, keep the area around the base of the center instrument panel console, between and under the front seats, free of objects that could also obstruct airﬂow to the rear seating area. For more information on how to use the main climate control system, see Dual Climate Control System on page 197. For information on ventilation, see Outlet Adjustment on page 200.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2007 Buick Terraza Owners Manual